Skip to main content

The Use of Entropy Labels in MPLS Forwarding
draft-ietf-mpls-entropy-label-02

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 6790.
Authors Kireeti Kompella , John Drake , Shane Amante , Wim Henderickx , Lucy Yong
Last updated 2012-05-07
Replaces draft-kompella-mpls-entropy-label
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd (None)
IESG IESG state Became RFC 6790 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-mpls-entropy-label-02
Network Working Group                                        K. Kompella
Internet-Draft                                                  J. Drake
Updates: 3031 (if approved)                             Juniper Networks
Intended status: Standards Track                               S. Amante
Expires: November 8, 2012                    Level 3 Communications, LLC
                                                           W. Henderickx
                                                          Alcatel-Lucent
                                                                 L. Yong
                                                              Huawei USA
                                                             May 7, 2012

              The Use of Entropy Labels in MPLS Forwarding
                    draft-ietf-mpls-entropy-label-02

Abstract

   Load balancing is a powerful tool for engineering traffic across a
   network.  This memo suggests ways of improving load balancing across
   MPLS networks using the concept of "entropy labels".  It defines the
   concept, describes why entropy labels are useful, enumerates
   properties of entropy labels that allow maximal benefit, and shows
   how they can be signaled and used for various applications.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on November 8, 2012.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents

Kompella, et al.        Expires November 8, 2012                [Page 1]
Internet-Draft             MPLS Entropy Labels                  May 2012

   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  Conventions used . . . . . . . . . . . . . . . . . . . . .  4
     1.2.  Motivation . . . . . . . . . . . . . . . . . . . . . . . .  6
   2.  Approaches . . . . . . . . . . . . . . . . . . . . . . . . . .  7
   3.  Entropy Labels and Their Structure . . . . . . . . . . . . . .  8
   4.  Data Plane Processing of Entropy Labels  . . . . . . . . . . .  9
     4.1.  Egress LSR . . . . . . . . . . . . . . . . . . . . . . . .  9
     4.2.  Ingress LSR  . . . . . . . . . . . . . . . . . . . . . . . 10
     4.3.  Transit LSR  . . . . . . . . . . . . . . . . . . . . . . . 11
     4.4.  Penultimate Hop LSR  . . . . . . . . . . . . . . . . . . . 11
   5.  Signaling for Entropy Labels . . . . . . . . . . . . . . . . . 11
     5.1.  LDP Signaling  . . . . . . . . . . . . . . . . . . . . . . 12
     5.2.  BGP Signaling  . . . . . . . . . . . . . . . . . . . . . . 12
     5.3.  RSVP-TE Signaling  . . . . . . . . . . . . . . . . . . . . 13
   6.  Operations, Administration, and Maintenance (OAM) and
       Entropy Labels . . . . . . . . . . . . . . . . . . . . . . . . 13
   7.  MPLS-TP and Entropy Labels . . . . . . . . . . . . . . . . . . 14
   8.  Point-to-Multipoint LSPs and Entropy Labels  . . . . . . . . . 15
   9.  Entropy Labels in Various Scenarios  . . . . . . . . . . . . . 15
     9.1.  LDP Tunnel . . . . . . . . . . . . . . . . . . . . . . . . 16
     9.2.  LDP Over RSVP-TE . . . . . . . . . . . . . . . . . . . . . 18
     9.3.  MPLS Applications  . . . . . . . . . . . . . . . . . . . . 18
   10. Security Considerations  . . . . . . . . . . . . . . . . . . . 18
   11. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 19
     11.1. Reserved Label for ELI . . . . . . . . . . . . . . . . . . 19
     11.2. LDP Entropy Label Capability TLV . . . . . . . . . . . . . 19
     11.3. BGP Entropy Label Capability Attribute . . . . . . . . . . 19
     11.4. RSVP-TE Entropy Label Capability flag  . . . . . . . . . . 19
   12. Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 20
   13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 20
     13.1. Normative References . . . . . . . . . . . . . . . . . . . 20
     13.2. Informative References . . . . . . . . . . . . . . . . . . 20
   Appendix A.  Applicability of LDP Entropy Label Capability TLV . . 21
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 22

Kompella, et al.        Expires November 8, 2012                [Page 2]
Internet-Draft             MPLS Entropy Labels                  May 2012

1.  Introduction

   Load balancing, or multi-pathing, is an attempt to balance traffic
   across a network by allowing the traffic to use multiple paths.  Load
   balancing has several benefits: it eases capacity planning; it can
   help absorb traffic surges by spreading them across multiple paths;
   it allows better resilience by offering alternate paths in the event
   of a link or node failure.

   As providers scale their networks, they use several techniques to
   achieve greater bandwidth between nodes.  Two widely used techniques
   are: Link Aggregation Group (LAG) and Equal-Cost Multi-Path (ECMP).
   LAG is used to bond together several physical circuits between two
   adjacent nodes so they appear to higher-layer protocols as a single,
   higher bandwidth 'virtual' pipe.  ECMP is used between two nodes
   separated by one or more hops, to allow load balancing over several
   shortest paths in the network.  This is typically obtained by
   arranging IGP metrics such that there are several equal cost paths
   between source-destination pairs.  Both of these techniques may, and
   often do, co-exist in various parts of a given provider's network,
   depending on various choices made by the provider.

   A very important requirement when load balancing is that packets
   belonging to a given 'flow' must be mapped to the same path, i.e.,
   the same exact sequence of links across the network.  This is to
   avoid jitter, latency and re-ordering issues for the flow.  What
   constitutes a flow varies considerably.  A common example of a flow
   is a TCP session.  Other examples are an L2TP session corresponding
   to a given broadband user, or traffic within an ATM virtual circuit.

   To meet this requirement, a node uses certain fields, termed 'keys',
   within a packet's header as input to a load balancing function
   (typically a hash function) that selects the path for all packets in
   a given flow.  The keys chosen for the load balancing function depend
   on the packet type; a typical set (for IP packets) is the IP source
   and destination addresses, the protocol type, and (for TCP and UDP
   traffic) the source and destination port numbers.  An overly
   conservative choice of fields may lead to many flows mapping to the
   same hash value (and consequently poorer load balancing); an overly
   aggressive choice may map a flow to multiple values, potentially
   violating the above requirement.

   For MPLS networks, most of the same principles (and benefits) apply.
   However, finding useful keys in a packet for the purpose of load
   balancing can be more of a challenge.  In many cases, MPLS
   encapsulation may require fairly deep inspection of packets to find
   these keys at transit LSRs.

Kompella, et al.        Expires November 8, 2012                [Page 3]
Internet-Draft             MPLS Entropy Labels                  May 2012

   One way to eliminate the need for this deep inspection is to have the
   ingress LSR of an MPLS Label Switched Path extract the appropriate
   keys from a given packet, input them to its load balancing function,
   and place the result in an additional label, termed the 'entropy
   label', as part of the MPLS label stack it pushes onto that packet.

   The packet's MPLS entire label stack can then be used by transit LSRs
   to perform load balancing, as the entropy label introduces the right
   level of "entropy" into the label stack.

   There are five key reasons why this is beneficial:

   1.  at the ingress LSR, MPLS encapsulation hasn't yet occurred, so
       deep inspection is not necessary;

   2.  the ingress LSR has more context and information about incoming
       packets than transit LSRs;

   3.  ingress LSRs usually operate at lower bandwidths than transit
       LSRs, allowing them to do more work per packet;

   4.  transit LSRs do not need to perform deep packet inspection and
       can load balance effectively using only a packet's MPLS label
       stack; and

   5.  transit LSRs, not having the full context that an ingress LSR
       does, have the hard choice between potentially misinterpreting
       fields in a packet as valid keys for load balancing (causing
       packet ordering problems) or adopting a conservative approach
       (giving rise to sub-optimal load balancing).  Entropy labels
       relieves them of making this choice.

   This memo describes why entropy labels are needed and defines the
   properties of entropy labels; in particular how they are generated
   and received, and the expected behavior of transit LSRs.  Finally, it
   describes in general how signaling works and what needs to be
   signaled, as well as specifics for the signaling of entropy labels
   for LDP ([RFC5036]), BGP ([RFC3107]), and RSVP-TE ([RFC3209]).

1.1.  Conventions used

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   The following acronyms are used:

Kompella, et al.        Expires November 8, 2012                [Page 4]
Internet-Draft             MPLS Entropy Labels                  May 2012

      BoS: Bottom of Stack

      CE: Customer Edge device

      ECMP: Equal Cost Multi-Path

      EL: Entropy Label

      ELC: Entropy Label Capability

      ELI: Entropy Label Indicator

      FEC: Forwarding Equivalence Class

      LAG: Link Aggregation Group

      LER: Label Edge Router

      LSR: Label Switching Router

      PE: Provider Edge Router

      PHP: Penultimate Hop Popping

      TC: Traffic Class

      TTL: Time-to-Live

      UHP: Ultimate Hop Popping

      VPLS: Virtual Private LAN (Local Area Network) Service

      VPN: Virtual Private Network

   The term ingress (or egress) LSR is used interchangeably with ingress
   (or egress) LER.  The term application throughout the text refers to
   an MPLS application (such as a VPN or VPLS).

   A label stack (say of three labels) is denoted by <L1, L2, L3>, where
   L1 is the "outermost" label and L3 the innermost (closest to the
   payload).  Packet flows are depicted left to right, and signaling is
   shown right to left (unless otherwise indicated).

   The term 'label' is used both for the entire 32-bit label and the 20-
   bit label field within a label.  It should be clear from the context
   which is meant.

Kompella, et al.        Expires November 8, 2012                [Page 5]
Internet-Draft             MPLS Entropy Labels                  May 2012

1.2.  Motivation

   MPLS is very successful generic forwarding substrate that transports
   several dozen types of protocols, most notably: IP, PWE3, VPLS and IP
   VPNs.  Within each type of protocol, there typically exist several
   variants, each with a different set of load balancing keys, e.g., for
   IP: IPv4, IPv6, IPv6 in IPv4, etc.; for PWE3: Ethernet, ATM, Frame-
   Relay, etc.  There are also several different types of Ethernet over
   PW encapsulation, ATM over PW encapsulation, etc. as well.  Finally,
   given the popularity of MPLS, it is likely that it will continue to
   be extended to transport new protocols.

   Currently, each transit LSR along the path of a given LSP has to try
   to infer the underlying protocol within an MPLS packet in order to
   extract appropriate keys for load balancing.  Unfortunately, if the
   transit LSR is unable to infer the MPLS packet's protocol (as is
   often the case), it will typically use the topmost (or all) MPLS
   labels in the label stack as keys for the load balancing function.
   The result may be an extremely inequitable distribution of traffic
   across equal-cost paths exiting that LSR.  This is because MPLS
   labels are generally fairly coarse-grained forwarding labels that
   typically describe a next-hop, or provide some of demultiplexing
   and/or forwarding function, and do not describe the packet's
   underlying protocol.

   On the other hand, an ingress LSR (e.g., a PE router) has detailed
   knowledge of an packet's contents, typically through a priori
   configuration of the encapsulation(s) that are expected at a given
   PE-CE interface, (e.g., IPv4, IPv6, VPLS, etc.).  They also have more
   flexible forwarding hardware.  PE routers need this information and
   these capabilities to:

      a) apply the required services for the CE;

      b) discern the packet's CoS forwarding treatment;

      c) apply filters to forward or block traffic to/from the CE;

      d) to forward routing/control traffic to an onboard management
      processor; and,

      e) load-balance the traffic on its uplinks to transit LSRs (e.g.,
      P routers).

   By knowing the expected encapsulation types, an ingress LSR router
   can apply a more specific set of payload parsing routines to extract
   the keys appropriate for a given protocol.  This allows for
   significantly improved accuracy in determining the appropriate load

Kompella, et al.        Expires November 8, 2012                [Page 6]
Internet-Draft             MPLS Entropy Labels                  May 2012

   balancing behavior for each protocol.

   If the ingress LSR were to capture the flow information so gathered
   in a convenient form for downstream transit LSRs, transit LSRs could
   remain completely oblivious to the contents of each MPLS packet, and
   use only the captured flow information to perform load balancing.  In
   particular, there will be no reason to duplicate an ingress LSR's
   complex packet/payload parsing functionality in a transit LSR.  This
   will result in less complex transit LSRs, enabling them to more
   easily scale to higher forwarding rates, larger port density, lower
   power consumption, etc.  The idea in this memo is to capture this
   flow information as a label, the so-called entropy label.

   Ingress LSRs can also adapt more readily to new protocols and extract
   the appropriate keys to use for load balancing packets of those
   protocols.  This means that deploying new protocols or services in
   edge devices requires fewer concomitant changes in the core,
   resulting in higher edge service velocity and at the same time more
   stable core networks.

2.  Approaches

   There are two main approaches to encoding load balancing information
   in the label stack.  The first allocates multiple labels for a
   particular Forwarding Equivalence Class (FEC).  These labels are
   equivalent in terms of forwarding semantics, but having multiple
   labels allows flexibility in assigning labels to flows belonging to
   the same FEC.  This approach has the advantage that the label stack
   has the same depth whether or not one uses label-based load
   balancing; and so, consequently, there is no change to forwarding
   operations on transit and egress LSRs.  However, it has a major
   drawback in that there is a significant increase in both signaling
   and forwarding state.

   The other approach encodes the load balancing information as an
   additional label in the label stack, thus increasing the depth of the
   label stack by one.  With this approach, there is minimal change to
   signaling state for a FEC; also, there is no change in forwarding
   operations in transit LSRs, and no increase of forwarding state in
   any LSR.  The only purpose of the additional label is to increase the
   entropy in the label stack, so this is called an "entropy label".
   This memo focuses solely on this approach.

   This latter approach uses upstream generated entropy labels, which
   may conflict with downstream allocated application labels.  There are
   a few approaches to deal with this: 1) allocate a pair of labels for
   each FEC, one that must have an entropy label below it, and one that

Kompella, et al.        Expires November 8, 2012                [Page 7]
Internet-Draft             MPLS Entropy Labels                  May 2012

   must not; 2) use a label (the "Entropy Label Indicator") to indicate
   that the next label is an entropy label; and 3) allow entropy labels
   only where there is no possible confusion.  The first doubles control
   and data plane state in the network; the last is too restrictive.
   The approach taken here is the second.  In making both the above
   choices, the trade-off is to increase label stack depth rather than
   control and data plane state in the network.

   Finally, one may choose to associate ELs with MPLS tunnels (LSPs), or
   with MPLS applications (e.g., VPNs).  (What this entails is described
   in later sections.)  We take the former approach, for the following
   reasons:

   1.  There are a small number of tunneling protocols for MPLS, but a
       large and growing number of applications.  Defining ELs on a
       tunnel basis means simpler standards, lower development,
       interoperability and testing efforts.

   2.  As a consequence, there will be much less churn in the network as
       new applications (services) are defined and deployed.

   3.  Processing application labels in the data plane is more complex
       than processing tunnel labels.  Thus, it is preferable to burden
       the latter rather than the former with EL processing.

   4.  Associating ELs with tunnels makes it simpler to deal with
       hierarchy, be it LDP-over-RSVP-TE or Carrier's Carrier VPNs.
       Each layer in the hierarchy can choose independently whether or
       not they want ELs.

   The cost of this approach is that ELIs will be mandatory; again, the
   trade-off is the size of the label stack.  To summarize, the net
   increase in the label stack to use entropy labels is two: one
   reserved label for the ELI, and the entropy label itself.

3.  Entropy Labels and Their Structure

   An entropy label (as used here) is a label:

   1.  that is not used for forwarding;

   2.  that is not signaled; and

   3.  whose only purpose in the label stack is to provide 'entropy' to
       improve load balancing.

   Entropy labels are generated by an ingress LSR, based entirely on

Kompella, et al.        Expires November 8, 2012                [Page 8]
Internet-Draft             MPLS Entropy Labels                  May 2012

   load balancing information.  However, they MUST NOT have values in
   the reserved label space (0-15) [IANA MPLS Label Values].  To ensure
   that they are not used inadvertently for forwarding, entropy labels
   SHOULD have a TTL of 0.  The CoS field of an entropy label can be set
   to any value deemed appropriate.

   Since entropy labels are generated by an ingress LSR, an egress LSR
   MUST be able to distinguish unambiguously between entropy labels and
   application labels.  This is accomplished by REQUIRING that the label
   immediately preceding an entropy label (EL) in the MPLS label stack
   be an 'entropy label indicator' (ELI).  The ELI is a reserved label
   with value (TBD by IANA).  An ELI MUST have 'Bottom of Stack' (BoS)
   bit = 0 ([RFC3032]).  The TTL SHOULD be set to whatever value the
   label above it in the stack has.  The CoS field can be set to any
   value deemed appropriate; typically, this will be the value in the
   label above the ELI in the label stack.

   Entropy labels are useful for pseudowires ([RFC4447]).
   [I-D.ietf-pwe3-fat-pw] explains how entropy labels can be used for
   RFC 4447-style pseudowires, and thus is complementary to this memo,
   which focuses on how entropy labels can be used for tunnels, and thus
   for all other MPLS applications.

4.  Data Plane Processing of Entropy Labels

4.1.  Egress LSR

   Suppose egress LSR Y is capable of processing entropy labels for a
   tunnel.  Y indicates this to all ingresses via signaling (see
   Section 5).  Y MUST be prepared to deal both with packets with an
   imposed EL and those without; the ELI will distinguish these cases.
   If a particular ingress chooses not to impose an EL, Y's processing
   of the received label stack (which might be empty) is as if Y chose
   not to accept ELs.

   If an ingress X chooses to impose an EL, then Y will receive a tunnel
   termination packet with label stack <TL, ELI, EL> <remaining packet
   header>.  Y recognizes TL as the label it distributed to its
   upstreams for the tunnel, and pops it.  (Note that TL may be the
   implicit null label, in which case it doesn't appear in the label
   stack.)  Y then recognizes the ELI and pops two labels: the ELI and
   the EL.  Y then processes the remaining packet header as normal; this
   may require further processing of tunnel termination, perhaps with
   further ELI+EL pairs.  When processing the final tunnel termination,
   Y MAY enqueue the packet based on that tunnel TL's or ELI's TC value,
   and MAY use the tunnel TL's or ELI's TTL to compute the TTL of the
   remaining packet header.  The EL's TTL MUST be ignored.

Kompella, et al.        Expires November 8, 2012                [Page 9]
Internet-Draft             MPLS Entropy Labels                  May 2012

   If any ELI processed by Y has BoS bit set, Y MUST discard the packet,
   and MAY log an error.  The EL's BoS bit will indicate whether or not
   there are more labels in the stack.

4.2.  Ingress LSR

   If an egress LSR Y indicates via signaling that it can process ELs on
   a particular tunnel, an ingress LSR X can choose whether or not to
   insert ELs for packets going into that tunnel.  Y MUST handle both
   cases.

   The steps that X performs to insert ELs are as follows:

   1.  On an incoming packet, identify the application to which the
       packet belongs, and thereby pick the fields to input to the load
       balancing function; call the output LB.

   2.  Determine the application label AL (if any).  Push <AL> onto the
       packet.

   3.  Based on the application, the load balancing output LB and other
       factors, determine the egress LSR Y, the tunnel to Y, the
       specific interface to the next hop, and thus the tunnel label TL.
       Use LB to generate the entropy label EL.

   4.  If, for the chosen tunnel, Y has not indicated that it can
       process ELs, push <TL> onto the packet.  If Y has indicated that
       it can process ELs for the tunnel, push <TL, ELI, EL> onto the
       packet.  X SHOULD put the same TTL and TC fields for the ELI as
       it does for TL.  The TTL for the EL MUST be zero.  The TC for the
       EL may be any value.

   5.  X then determines whether further tunnel hierarchy is needed; if
       so, X goes back to step 3, possibly with a new egress Y for the
       new tunnel.  Otherwise, X is done, and sends out the packet.

   Notes:

   a.  X computes load balancing information and generates the EL based
       on the incoming application packet, even though the signaling of
       EL capability is associated with tunnels.

   b.  X MAY insert several entropy labels in the stack (each, of
       course, preceded by an ELI), potentially one for each
       hierarchical tunnel, provided that the egress for that tunnel has
       indicated that it can process ELs for that tunnel.

Kompella, et al.        Expires November 8, 2012               [Page 10]
Internet-Draft             MPLS Entropy Labels                  May 2012

   c.  X MUST NOT include an entropy label for a given tunnel unless the
       egress LSR Y has indicated that it can process entropy labels for
       that tunnel.

   d.  The signaling and use of entropy labels in one direction
       (signaling from Y to X, and data path from X to Y) is completely
       independent of the signaling and use of entropy labels in the
       reverse direction (signaling from X to Y, and data path from Y to
       X).

4.3.  Transit LSR

   Transit LSRs MAY operate with no change in forwarding behavior.  The
   following are suggestions for optimizations that improve load
   balancing, reduce the amount of packet data processed, and/or enhance
   backward compatibility.

   If a transit LSR recognizes the ELI, it MAY choose to load balance
   solely on the following label (the EL); otherwise, it SHOULD use as
   much of the whole label stack as feasible as keys for the load
   balancing function, with the exception that reserved labels MUST NOT
   be used.

   Some transit LSRs look beyond the label stack for better load
   balancing information.  This is a simple, backward compatible
   approach in networks where some ingress LSRs impose ELs and others
   don't.  However, this is of limited incremental value if an EL is
   indeed present, and requires more packet processing from the LSR.  A
   transit LSR MAY choose to parse the label stack for the presence of
   the ELI, and look beyond the label stack only if it does not find it,
   thus retaining the old behavior when needed, yet avoided unnecessary
   work if not.

4.4.  Penultimate Hop LSR

   No change is needed at penultimate hop LSRs.

5.  Signaling for Entropy Labels

   An egress LSR Y can signal to ingress LSR(s) its ability to process
   entropy labels (henceforth called "Entropy Label Capability" or ELC)
   on a given tunnel.  Note that Entropy Label Capability may be
   asymmetric: if LSRs X and Y are at opposite ends of a tunnel, X may
   be able to process entropy labels, whereas Y may not.  The signaling
   extensions below allow for this asymmetry.

   For an illustration of signaling and forwarding with entropy labels,

Kompella, et al.        Expires November 8, 2012               [Page 11]
Internet-Draft             MPLS Entropy Labels                  May 2012

   see Section 9.

5.1.  LDP Signaling

   A new LDP TLV ([RFC5036]) is defined to signal an egress's ability to
   process entropy labels.  This is called the ELC TLV, and may appear
   as an Optional Parameter of the Label Mapping Message TLV.

   The presence of the ELC TLV in a Label Mapping Message indicates to
   ingress LSRs that the egress LSR can process entropy labels for the
   associated LDP tunnel.  The ELC TLV has Type (TBD by IANA) and Length
   0.

   The structure of the ELC TLV is shown below.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |U|F|        Type (TBD)         |           Length (0)          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                  Figure 1: Entropy Label Capability TLV

   where:

      U: Unknown bit.  This bit MUST be set to 1.  If the Entropy Label
      Capability TLV is not understood, then the TLV is not known to the
      receiver and MUST be ignored.

      F: Forward bit.  This bit MUST be set be set to 1.  Since this
      Capability TLV is going to be propagated hop-by-hop, the TLV
      should be forwarded even by nodes that may not understand it.

      Type: Type field.  To be assigned by IANA.

      Length: Length field.  This field specifies the total length in
      octets of the ELC TLV, and is currently defined to be 0.

5.2.  BGP Signaling

   When BGP [RFC4271] is used for distributing Network Layer
   Reachability Information (NLRI) as described in, for example,
   [RFC3107], the BGP UPDATE message may include the ELC attribute as
   part of the Path Attributes.  This is an optional, transitive BGP
   attribute of type (to be assigned by IANA).  The inclusion of this
   attribute with an NLRI indicates that the advertising BGP router can
   process entropy labels as an egress LSR for all routes in that NLRI.

Kompella, et al.        Expires November 8, 2012               [Page 12]
Internet-Draft             MPLS Entropy Labels                  May 2012

   A BGP speaker S that originates an UPDATE should include the ELC
   attribute only if both of the following are true:

   A1:  S sets the BGP NEXT_HOP attribute to itself; AND

   A2:  S can process entropy labels.

   Suppose a BGP speaker T receives an UPDATE U with the ELC attribute.
   T has two choices.  T can simply re-advertise U with the ELC
   attribute if either of the following is true:

   B1:  T does not change the NEXT_HOP attribute; OR

   B2:  T simply swaps labels without popping the entire label stack and
        processing the payload below.

   An example of the use of B1 is Route Reflectors.

   However, if T changes the NEXT_HOP attribute for U and in the data
   plane pops the entire label stack to process the payload, T MAY
   include an ELC attribute for UPDATE U' if both of the following are
   true:

   C1:  T sets the NEXT_HOP attribute of U' to itself; AND

   C2:  T can process entropy labels.

   Otherwise, T MUST remove the ELC attribute.

5.3.  RSVP-TE Signaling

   Entropy Label support is signaled in RSVP-TE [RFC3209] using the
   Entropy Label Capability (ELC) flag in the Attribute Flags TLV of the
   LSP_ATTRIBUTES object [RFC5420].  The presence of the ELC flag in a
   Path message indicates that the ingress can process entropy labels in
   the upstream direction; this only makes sense for a bidirectional LSP
   and MUST be ignored otherwise.  The presence of the ELC flag in a
   Resv message indicates that the egress can process entropy labels in
   the downstream direction.

   The bit number for the ELC flag is to be assigned by IANA.

6.  Operations, Administration, and Maintenance (OAM) and Entropy Labels

   Generally OAM comprises a set of functions operating in the data
   plane to allow a network operator to monitor its network
   infrastructure and to implement mechanisms in order to enhance the

Kompella, et al.        Expires November 8, 2012               [Page 13]
Internet-Draft             MPLS Entropy Labels                  May 2012

   general behavior and the level of performance of its network, e.g.,
   the efficient and automatic detection, localization, diagnosis and
   handling of defects.

   Currently defined OAM mechanisms for MPLS include LSP Ping/Traceroute
   [RFC4379] and Bidirectional Failure Detection (BFD) for MPLS
   [RFC5884].  The latter provides connectivity verification between the
   endpoints of an LSP, and recommends establishing a separate BFD
   session for every path between the endpoints.

   The LSP traceroute procedures of [RFC4379] allow an ingress LSR to
   obtain label ranges that can be used to send packets on every path to
   the egress LSR.  It works by having ingress LSR sequentially ask the
   transit LSRs along a particular path to a given egress LSR to return
   a label range such that the inclusion of a label in that range in a
   packet will cause the replying transit LSR to send that packet out
   the egress interface for that path.  The ingress provides the label
   range returned by transit LSR N to transit LSR N + 1, which returns a
   label range which is less than or equal in span to the range provided
   to it.  This process iterates until the penultimate transit LSR
   replies to the ingress LSR with a label range that is acceptable to
   it and to all LSRs along path preceding it for forwarding a packet
   along the path.

   However, the LSP traceroute procedures do not specify where in the
   label stack the value from the label range is to be placed, whether
   deep packet inspection is allowed and if so, which keys and key
   values are to be used.

   This memo updates LSP traceroute by specifying that the value from
   the label range is to be placed in the entropy label.  Deep packet
   inspection is thus not necessary, although an LSR may use it,
   provided it do so consistently, i.e., if the label range to go to a
   given downstream LSR is computed with deep packet inspection, then
   the data path should use the same approach and the same keys.

   In order to have a BFD session on a given path, a value from the
   label range for that path should be used as the EL value for BFD
   packets sent on that path.

7.  MPLS-TP and Entropy Labels

   Since MPLS-TP does not use ECMP, entropy labels are not applicable to
   an MPLS-TP deployment.

Kompella, et al.        Expires November 8, 2012               [Page 14]
Internet-Draft             MPLS Entropy Labels                  May 2012

8.  Point-to-Multipoint LSPs and Entropy Labels

   Point-to-Multipoint (P2MP) LSPs [RFC4875] typically do not use ECMP
   for load balancing, as the combination of replication and
   multipathing can lead to duplicate traffic delivery.  However, P2MP
   LSPs can traverse bundled links [RFC4201] and LAGs.  In both these
   cases, load balancing is useful, and hence entropy labels can be of
   value for P2MP LSPs.

   There is a potential complication with the use of entropy labels in
   the context of P2MP LSPs, a consequence of the fact that the entire
   label stack below the P2MP label must be the same for all egress
   LSRs.  This is that all egress LSRs must be willing to receive
   entropy labels; if even one egress LSR is not willing, then entropy
   labels MUST NOT be used for this P2MP LSP.

   In this regard, the ingress LSR MUST keep track of the ability of
   each egress LSR to process entropy labels, especially since the set
   of egress LSRs of a given P2MP LSP may change over time.  Whenever an
   existing egress LSR leaves, or a new egress LSR joins the P2MP LSP,
   the ingress MUST re-evaluate whether or not to include entropy labels
   for the P2MP LSP.

   In some cases, it may be feasible to deploy two P2MP LSPs, one to ELC
   egress LSRs, and the other to the remaining non-ELC egress LSRs.
   However, this requires more state in the network, more bandwidth, and
   more operational overhead (tracking ELC LSRs, and provisioning P2MP
   LSPs accordingly).  Alternatively, an ingress LSR may choose to
   signal two separate P2MP LSPs, one to ELC egresses, the other to non-
   ELC egresses, trading off implementation complexity for operational
   complexity.

9.  Entropy Labels in Various Scenarios

   This section describes the use of entropy labels in various
   scenarios.

   In the figures below, the following conventions used to depict
   processing between X and Y. Note that control plane signaling goes
   right to left, whereas data plane processing goes left to right.

   Protocols
   Y:        <--- [L, E]                         Y signals L to X
       X ------------- Y
   LS:   <L, ELI, EL>                            Label stack
   X:  +<L, ELI, EL>                             X pushes <L, ELI, EL>
   Y:                  -<L, ELI, EL>             Y pops <L, ELI, EL>

Kompella, et al.        Expires November 8, 2012               [Page 15]
Internet-Draft             MPLS Entropy Labels                  May 2012

   This means that Y signals to X label L for an LDP tunnel.  E can be
   one of:

      0: meaning egress is NOT entropy label capable, or

      1: meaning egress is entropy label capable.

   The line with LS: shows the label stack on the wire.  Below that is
   the operation that each LSR does in the data plane, where + means
   push the following label stack, - means pop the following label
   stack, L~L' means swap L with L', and * means that the operation is
   not depicted.

9.1.  LDP Tunnel

   The following illustrates several simple intra-AS LDP tunnels.  The
   first diagram shows ultimate hop popping (UHP) with ingress inserting
   an EL, the second UHP with no ELs, the third PHP with ELs, and
   finally, PHP with no ELs, but also with an application label AL
   (which could, for example, be a VPN label).

   Note that, in all the cases below, the MPLS application does not
   matter; it may be that X pushes some more labels (perhaps for a VPN
   or VPLS) below the ones shown, and Y pops them.

   A:        <--- [TL4, 1]
   B:                     <-- [TL3, 1]
   ...
   W:                           <-- [TL1, 1]
   Y:                                        <-- [TL0, 1]
       X --------------- A --------- B ... W ---------- Y
   LS:    <TL4, ELI, EL>   <TL3,ELI,EL>      <TL0,ELI,EL>
   X:  +<TL4, ELI, EL>
   A:                    TL4~TL3
   B:                                TL3~TL2
   ...
   W:                                      TL1~TL0
   Y:                                                   -<TL0, ELI, EL>

                     LDP with UHP; ingress inserts ELs

Kompella, et al.        Expires November 8, 2012               [Page 16]
Internet-Draft             MPLS Entropy Labels                  May 2012

   A:        <--- [TL4, 1]
   B:                     <-- [TL3, 1]
   ...
   W:                           <-- [TL1, 1]
   Y:                                        <-- [TL0, 1]
       X --------------- A --------- B ... W ---------- Y
   LS:        <TL4>          <TL3>              <TL0>
   X:  +<TL4>
   A:                    TL4~TL3
   B:                                TL3~TL2
   ...
   W:                                      TL1~TL0
   Y:                                                   -<TL0>

                 LDP with UHP; ingress does not insert ELs

   A:        <--- [TL4, 1]
   B:                     <-- [TL3, 1]
   ...
   W:                           <-- [TL1, 1]
   Y:                                          <-- [3, 1]
       X --------------- A --------- B ... W ---------- Y
   X:  +<TL4, ELI, EL>
   A:                    TL4~TL3
   B:                                TL3~TL2
   ...
   W:                                      -TL1
   Y:                                                   -<ELI, EL>

                     LDP with PHP; ingress inserts ELs

   A:        <--- [TL4, 1]
   B:                     <-- [TL3, 1]
   ...
   W:                           <-- [TL1, 1]
   Y:                                          <-- [3, 1]
   VPN:  <------------------------------------------ [AL]
       X --------------- A --------- B ... W ---------- Y
   LS:      <TL4, AL>      <TL3, AL>             <AL>
   X:  +<TL4, AL>
   A:                    TL4~TL3
   B:                                TL3~TL2
   ...
   W:                                      -TL1
   Y:                                                   -<AL>

Kompella, et al.        Expires November 8, 2012               [Page 17]
Internet-Draft             MPLS Entropy Labels                  May 2012

              LDP with PHP + VPN; ingress does not insert ELs

9.2.  LDP Over RSVP-TE

   The following illustrates "LDP over RSVP-TE" tunnels.  X and Y are
   the ingress and egress (respectively) of the LDP tunnel; A and W are
   the ingress and egress of the RSVP-TE tunnel.  It is assumed that
   both the LDP and RSVP-TE tunnels have PHP.

   LDP with ELs, RSVP-TE without ELs
   LDP:       <--- [L4, 1]  <------- [L3, 1]  <--- [3, 1]
   RSVP-TE:                <-- [Rn, 0]
                                  <-- [3, 0]
       X --------------- A --------- B ... W ---------- Y
   LS:    <L4, ELI, EL>   <Rn,L3,ELI,EL> ...  <ELI, EL>
   DP: +<L4, ELI, EL>    L4~<Rn, L3> *     -L1          -<ELI, EL>

                    Figure 2: LDP over RSVP-TE Tunnels

9.3.  MPLS Applications

   An ingress LSR X must keep state per unicast tunnel as to whether the
   egress for that tunnel can process entropy labels.  X does not have
   to keep state per application running over that tunnel.  However, an
   ingress PE can choose on a per-application basis whether or not to
   insert ELs.  For example, X may have an application for which it does
   not wish to use ECMP (e.g., circuit emulation), or for which it does
   not know which keys to use for load balancing (e.g., Appletalk over a
   pseudowire).  In either of those cases, X may choose not to insert
   entropy labels, but may choose to insert entropy labels for an IP VPN
   over the same tunnel.

10.  Security Considerations

   This document describes advertisement of the capability to support
   receipt of entropy labels which an ingress LSR may insert in MPLS
   packets in order to allow transit LSRs to attain better load
   balancing across LAG and/or ECMP paths in the network.

   This document does not introduce new security vulnerabilities to LDP,
   BGP or RSVP-TE.  Please refer to the Security Considerations section
   of these protocols ([RFC5036], [RFC4271] and [RFC3209]) for security
   mechanisms applicable to each.

   Given that there is no end-user control over the values used for
   entropy labels, there is little risk of Entropy Label forgery which
   could cause uneven load-balancing in the network.

Kompella, et al.        Expires November 8, 2012               [Page 18]
Internet-Draft             MPLS Entropy Labels                  May 2012

   If Entropy Label Capability is not signaled from an egress PE to an
   ingress PE, due to, for example, malicious configuration activity on
   the egress PE, then the PE will fall back to not using entropy labels
   for load-balancing traffic over LAG or ECMP paths which is in general
   no worse than the behavior observed in current production networks.
   That said, it is recommended that operators monitor changes to PE
   configurations and, more importantly, the fairness of load
   distribution over LAG or ECMP paths.  If the fairness of load
   distribution over a set of paths changes that could indicate a
   misconfiguration, bug or other non-optimal behavior on their PEs and
   they should take corrective action.

11.  IANA Considerations

11.1.  Reserved Label for ELI

   IANA is requested to allocate a reserved label for the Entropy Label
   Indicator (ELI) from the "Multiprotocol Label Switching Architecture
   (MPLS) Label Values" Registry.

11.2.  LDP Entropy Label Capability TLV

   IANA is requested to allocate the next available value from the IETF
   Consensus range in the LDP TLV Type Name Space Registry as the
   "Entropy Label Capability TLV".

11.3.  BGP Entropy Label Capability Attribute

   IANA is requested to allocate the next available Path Attribute Type
   Code from the "BGP Path Attributes" registry as the "BGP Entropy
   Label Capability Attribute".

11.4.  RSVP-TE Entropy Label Capability flag

   IANA is requested to allocate a new bit from the "Attribute Flags"
   sub-registry of the "RSVP TE Parameters" registry.

   Bit | Name                     | Attribute  | Attribute  | RRO
   No  |                          | Flags Path | Flags Resv |
   ----+--------------------------+------------+------------+-----
   TBD   Entropy Label Capability       Yes          Yes       No

Kompella, et al.        Expires November 8, 2012               [Page 19]
Internet-Draft             MPLS Entropy Labels                  May 2012

12.  Acknowledgments

   We wish to thank Ulrich Drafz for his contributions, as well as the
   entire 'hash label' team for their valuable comments and discussion.

   Sincere thanks to Nischal Sheth for his many suggestions and
   comments, and his careful reading of the document, especially with
   regard to data plane processing of entropy labels.

13.  References

13.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3032]  Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
              Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
              Encoding", RFC 3032, January 2001.

   [RFC3107]  Rekhter, Y. and E. Rosen, "Carrying Label Information in
              BGP-4", RFC 3107, May 2001.

   [RFC3209]  Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
              and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
              Tunnels", RFC 3209, December 2001.

   [RFC5420]  Farrel, A., Papadimitriou, D., Vasseur, JP., and A.
              Ayyangarps, "Encoding of Attributes for MPLS LSP
              Establishment Using Resource Reservation Protocol Traffic
              Engineering (RSVP-TE)", RFC 5420, February 2009.

13.2.  Informative References

   [I-D.ietf-pwe3-fat-pw]
              Bryant, S., Filsfils, C., Drafz, U., Kompella, V., Regan,
              J., and S. Amante, "Flow Aware Transport of Pseudowires
              over an MPLS Packet Switched Network",
              draft-ietf-pwe3-fat-pw-07 (work in progress), July 2011.

   [RFC4201]  Kompella, K., Rekhter, Y., and L. Berger, "Link Bundling
              in MPLS Traffic Engineering (TE)", RFC 4201, October 2005.

   [RFC4271]  Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
              Protocol 4 (BGP-4)", RFC 4271, January 2006.

   [RFC4364]  Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private

Kompella, et al.        Expires November 8, 2012               [Page 20]
Internet-Draft             MPLS Entropy Labels                  May 2012

              Networks (VPNs)", RFC 4364, February 2006.

   [RFC4379]  Kompella, K. and G. Swallow, "Detecting Multi-Protocol
              Label Switched (MPLS) Data Plane Failures", RFC 4379,
              February 2006.

   [RFC4447]  Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G.
              Heron, "Pseudowire Setup and Maintenance Using the Label
              Distribution Protocol (LDP)", RFC 4447, April 2006.

   [RFC4761]  Kompella, K. and Y. Rekhter, "Virtual Private LAN Service
              (VPLS) Using BGP for Auto-Discovery and Signaling",
              RFC 4761, January 2007.

   [RFC4762]  Lasserre, M. and V. Kompella, "Virtual Private LAN Service
              (VPLS) Using Label Distribution Protocol (LDP) Signaling",
              RFC 4762, January 2007.

   [RFC4875]  Aggarwal, R., Papadimitriou, D., and S. Yasukawa,
              "Extensions to Resource Reservation Protocol - Traffic
              Engineering (RSVP-TE) for Point-to-Multipoint TE Label
              Switched Paths (LSPs)", RFC 4875, May 2007.

   [RFC5036]  Andersson, L., Minei, I., and B. Thomas, "LDP
              Specification", RFC 5036, October 2007.

   [RFC5586]  Bocci, M., Vigoureux, M., and S. Bryant, "MPLS Generic
              Associated Channel", RFC 5586, June 2009.

   [RFC5884]  Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow,
              "Bidirectional Forwarding Detection (BFD) for MPLS Label
              Switched Paths (LSPs)", RFC 5884, June 2010.

Appendix A.  Applicability of LDP Entropy Label Capability TLV

   In the case of unlabeled IPv4 (Internet) traffic, the Best Current
   Practice is for an egress LSR to propagate eBGP learned routes within
   a SP's Autonomous System after resetting the BGP next-hop attribute
   to one of its Loopback IP addresses.  That Loopback IP address is
   injected into the Service Provider's IGP and, concurrently, a label
   assigned to it via LDP.  Thus, when an ingress LSR is performing a
   forwarding lookup for a BGP destination it recursively resolves the
   associated next-hop to a Loopback IP address and associated LDP label
   of the egress LSR.

   Thus, in the context of unlabeled IPv4 traffic, the LDP Entropy Label
   Capability TLV will typically be applied only to the FEC for the

Kompella, et al.        Expires November 8, 2012               [Page 21]
Internet-Draft             MPLS Entropy Labels                  May 2012

   Loopback IP address of the egress LSR and the egress LSR need not
   announce an entropy label capability for the eBGP learned route.

Authors' Addresses

   Kireeti Kompella
   Juniper Networks
   1194 N. Mathilda Ave.
   Sunnyvale, CA  94089
   US

   Email: kireeti@juniper.net

   John Drake
   Juniper Networks
   1194 N. Mathilda Ave.
   Sunnyvale, CA  94089
   US

   Email: jdrake@juniper.net

   Shane Amante
   Level 3 Communications, LLC
   1025 Eldorado Blvd
   Broomfield, CO  80021
   US

   Email: shane@level3.net

   Wim Henderickx
   Alcatel-Lucent
   Copernicuslaan 50
   2018 Antwerp
   Belgium

   Email: wim.henderickx@alcatel-lucent.com

Kompella, et al.        Expires November 8, 2012               [Page 22]
Internet-Draft             MPLS Entropy Labels                  May 2012

   Lucy Yong
   Huawei USA
   5340 Legacy Dr.
   Plano, TX  75024
   US

   Email: lucy.yong@huawei.com

Kompella, et al.        Expires November 8, 2012               [Page 23]