Requirements for Interfaces of Network Digital Twin
draft-chen-nmrg-dtn-interface-01
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Active".
|
|
|---|---|---|---|
| Authors | Danyang Chen , Hongwei Yang , Cheng Zhou | ||
| Last updated | 2023-03-13 | ||
| RFC stream | (None) | ||
| Formats | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-chen-nmrg-dtn-interface-01
Internet Research Task Force D. Chen
Internet-Draft H. Yang
Intended status: Informational C. Zhou
Expires: 9 September 2023 China Mobile
8 March 2023
Requirements for Interfaces of Network Digital Twin
draft-chen-nmrg-dtn-interface-01
Abstract
The interfaces of Digital Twin Network can be divided as twin network
southbound interface, internal interface and northbound interface.
In order to build a digital twin network and realize its many
advantages, different interfaces should be able to meet different
requirements. And this memo introduces the requirements for the
interfaces of the Digital Twin Network.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 9 September 2023.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
Chen, et al. Expires 9 September 2023 [Page 1]
Internet-Draft Network Working Group March 2023
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Requirements for Different Interfaces . . . . . . . . . . . . 3
3. Suggestions on the applicability of common protocols . . . . 6
4. Security Considerations . . . . . . . . . . . . . . . . . . . 7
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
6. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1. Informative References . . . . . . . . . . . . . . . . . 7
6.2. Normative References . . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
As defined in the[I-D.irtf-nmrg-network-digital-twin-arch] , the
digital twin network is defined as "a network system with a physical
network entity and a virtual twin, and the two can interact with each
other in real time". It should have four core elements: data, model,
mapping and interaction. Accordingly, a "three-layer, three-domain
and double-closed loop" architecture is adopted.) and the network
telemetry technology
Based on the above architecture definition of three-layer, three-
domain and double-closed-loop, the interfaces of each layer and their
positions of the digital twin network are shown in Figure 1. The
network elements in the physical entity network exchange network data
and network control information with the twin network layer through
the twin southbound interface. The twin network layer contains three
key subsystems, which are data sharing warehouse, service mapping
model and digital twin management. Through the corresponding
interface protocol, the construction and interaction requirements of
the three key subsystems should be met. And through the internal
interface of the twin layer, the interaction between the three key
subsystems and the physical network layer and network application
layer is realized. Network applications input requirements to the
twin network layer through the twin northbound interface, and deploy
services in the twin network layer through the model example. To sum
up, there are differences in interface protocol requirements between
different layers of DTN and within twin layers.
Chen, et al. Expires 9 September 2023 [Page 2]
Internet-Draft Network Working Group March 2023
+---------------------------------------------------------------------+
| |
| Network Application Layer |
| |
+-------^-------------------------^----------------------^------------+
| | |
Twin
| | | Northbound
| | | Interface
+-------v-------------------------v----------------------v-----------+
| Twin Network Layer |
| |
| +------------+ +----------+ +---------------+ |
| | data | | service | | digital | |
| | sharing <-----------> mapping <----------> twin | |
| | warehouse | Twin | model | | management | |
| +------------+ Internal +----------+ +---------------+ |
| Interface |
+--------^------------------------^-----------------------^----------+
| | | Twin
| | | Southbound
| | | Interface
+--------v------------------------v-----------------------v-----------+
| |
| Physical Network Layer |
| |
+---------------------------------------------------------------------+
Figure 1: Schematic Representation of DTN Interface
2. Requirements for Different Interfaces
* Twin northbound interface
- The twin northbound interface is the interface between the
network application layer and the twin network layer. The
network application requirements are input from the twin
northbound interface to the twin network layer. The twin
northbound interface can support the rapid deployment of
network applications such as network operation and
optimization, network visualization, intent verification, and
network automatic driving with lower cost, higher efficiency,
and less impact on live network services. Therefore, the twin
northbound interface should have the characteristics of the
following 4 aspects.
Chen, et al. Expires 9 September 2023 [Page 3]
Internet-Draft Network Working Group March 2023
o Openness: The twin northbound interface must meet the
business requirements of different network applications and
can be input to the twin network layer, so it needs to have
good openness and compatibility;
o Scalability: There are a variety of network applications in
the network application layer, which will inevitably lead to
the generation of network applications. At the same time,
the continuous development of the network is bound to
introduce new network applications. With the upgrade of
network applications and the generation of new applications,
the twin northbound interface should be able to expand in
time to meet the needs of new network applications;
o Portability: There are twins with different sizes and
functions in the twin network layer. The same or similar
requirements of various applications in the network
application layer may be deployed on different twins.
Therefore, the twin northbound interface should be easily
transplanted and deployed on different twins;
o Flexible deployment: To reduce deployment time and cost,
twin northbound interfaces must be flexibly deployed.
* Twin Internal interface
- As shown in the "three-layer, three-domain, double-closed loop"
of DTN architecture, the twin network layer contains three key
subsystems, namely, data sharing warehouse, service mapping
model and digital twin management, which is the most critical
part of the digital twin network. The internal interface of
the twin layer refers to the interface within and between the
three subsystems: data sharing warehouse, service mapping model
and digital Twin management. In order to support the functions
of the three subsystems in the twin network layer and the
interaction between the three subsystems, the internal
interface of the twin layer should have the following four
functions.
o Unity: Each subsystem in the twin network layer should be
able to provide the same data format and data service for
other subsystems through the internal interface of the twin
layer, that is, the interface should have unity.
Chen, et al. Expires 9 September 2023 [Page 4]
Internet-Draft Network Working Group March 2023
o Adaptability: The twin network layer must interact with the
network application layer and the physical network layer,
and should be well adapted to various network devices and
interfaces. Therefore, the internal interfaces of the twin
layer also need to be adaptive.
o Portability: The data model instances provided by the
service mapping model subsystem for different applications
may have a high degree of similarity. In order to improve
efficiency, the data model instances must be able to be
provided and deployed through different internal interfaces
of twin layers.
o Flexible and extensible: The twin network layer must be able
to verify different new network services. In order to
shorten the implementation time of functions, the
implementation of functions inside the twin layer should be
simplified as far as possible. Therefore, the internal
interface of the twin network layer must be flexible and
extensible.
* Twin southbound interface
- The twin southbound interface is the interface between the twin
network layer and the physical entity network. Control updates
are delivered from the twin southbound interface to the
physical entity network, and various nes in the physical entity
network exchange network data and network control information
with the twin network layer through the twin southbound
interface. Therefore, the southbound twin interface should
have three functions.
o Information interaction capability: the twin southbound
interface should be able to collect the information of
different physical nes or network devices, and send the
configuration information of the twin network to the
physical network for execution, that is, it can realize the
information interaction between the twin network layer and
the physical entity network.
o Real-time: The realization of twin network configuration
verification and other functions must have certain real-
time, so the information collected and uploaded from the
physical entity network and the configuration information
sent from the twin network to the physical network must have
certain real-time, in order to meet the real-time
requirements of the digital twin network.
Chen, et al. Expires 9 September 2023 [Page 5]
Internet-Draft Network Working Group March 2023
o Compatibility: Network devices and nes from different
manufacturers use different interfaces and protocols. The
southbound interfaces must be compatible to ensure the
reliability of information collection and configuration
delivery.
3. Suggestions on the applicability of common protocols
With the development of communication networks, many North-South and
intra-network communication protocols have been formed in the
network, such as RESTCONFRFC 8527 [RFC8527], NETCONFRFC 8526
[RFC8526], OpenFlow, XMPPRFC 7622 [RFC7622], East-West Bridge, etc..
Because different communication protocols have different
characteristics, the existing protocols are suitable for different
twin network interfaces. In this draft, we attempt to give some
suggestions about the applicability of some existing general
protocols suitable for DTN construction.
RESTCONF uses the Hypertext Transfer Protocol (HTTP) as the
transport protocol and XML/JSON as the message exchange format,
allowing WEB applications to access configuration and operation
data of network devices in a modular and extensible manner. It
applies to twin northbound interfaces.
NETCONF uses remote procedure call ( RPC) based mechanism to
provide a set of framework mechanism to add, modify, delete
network device configuration, query configuration, status and
statistics between the client and the server, and can be used as a
network administrator or network configuration application and
network device logical connection. NETCONF can transmit
configuration data and status data. So it can be used for twin
northbound interfaces and twin southbound interfaces.
OpenFlow are used for information exchange between OpenFlow
switches and controllers, so it appllies to twin southbound
interfaces.
Extensible Message Processing Thread Protocol (XMPP) is an open
technology for instant messaging, multi-party chat, voice and
video calling, collaboration, content syndication, and generic XML
data routing, so it is suitable for twin southbound interfaces and
twin internal interfaces.
Routing system interface protocols (I2RS) dynamically deliver
routing status and policies based on topology changes and traffic
statistics, enabling external applications or controlling entities
to read router information and it can also be used for twin
southbound interfaces and twin internal interfaces.
Chen, et al. Expires 9 September 2023 [Page 6]
Internet-Draft Network Working Group March 2023
East-West Bridge is an application-layer protocol based on
Transmission Control Protocol/Secure Socket Protocol (TCP/SSL),
which has good portability and scalability. NEs can be abstracted
into concepts such as nodes, links, ports, and flows. The
extended link layer discovery protocol is used to obtain the ID,
capacity, and status of each NE in the domain. So it applies for
twin internal interfaces.
Simple Network Management Protocol (SNMP) is a standard protocol
specifically designed to manage network nodes over IP networks.
Network administrators can use SNMP to manage network performance,
identify and resolve network problems, and plan network growth.
It can be used for twin northbound interfaces and twin internal
interfaces.
4. Security Considerations
TBD
5. IANA Considerations
This document has no requests to IANA.
6. References
6.1. Informative References
[I-D.irtf-nmrg-network-digital-twin-arch]
Zhou, C., Yang, H., Duan, X., Lopez, D., Pastor, A., Wu,
Q., Boucadair, M., and C. Jacquenet, "Digital Twin
Network: Concepts and Reference Architecture", Work in
Progress, Internet-Draft, draft-irtf-nmrg-network-digital-
twin-arch-02, 24 October 2022,
<https://datatracker.ietf.org/doc/html/draft-irtf-nmrg-
network-digital-twin-arch-02>.
6.2. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7622] Saint-Andre, P., "Extensible Messaging and Presence
Protocol (XMPP): Address Format", RFC 7622,
DOI 10.17487/RFC7622, September 2015,
<https://www.rfc-editor.org/info/rfc7622>.
Chen, et al. Expires 9 September 2023 [Page 7]
Internet-Draft Network Working Group March 2023
[RFC8526] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "NETCONF Extensions to Support the Network
Management Datastore Architecture", RFC 8526,
DOI 10.17487/RFC8526, March 2019,
<https://www.rfc-editor.org/info/rfc8526>.
[RFC8527] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "RESTCONF Extensions to Support the Network
Management Datastore Architecture", RFC 8527,
DOI 10.17487/RFC8527, March 2019,
<https://www.rfc-editor.org/info/rfc8527>.
Authors' Addresses
Danyang Chen
China Mobile
Beijing
100053
China
Email: chendanyang@chinamobile.com
Hongwei Yang
China Mobile
Beijing
100053
China
Email: yanghongwei@chinamobile.com
Cheng Zhou
China Mobile
Beijing
100053
China
Email: zhouchengyjy@chinamobile.com
Chen, et al. Expires 9 September 2023 [Page 8]