Skip to main content

Transmission of IPv6 Packets over Near Field Communication
draft-ietf-6lo-nfc-02

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 9428.
Authors Joo-Sang Youn , Yong-Geun Hong
Last updated 2015-10-17
Replaces draft-hong-6lo-ipv6-over-nfc
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd james woodyatt
IESG IESG state Became RFC 9428 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-6lo-nfc-02
6Lo Working Group                                              Y-G. Hong
Internet-Draft                                                 Y-H. Choi
Intended status: Standards Track                                    ETRI
Expires: April 19, 2016                                        J-S. Youn
                                                           DONG-EUI Univ
                                                                D-K. Kim
                                                                     KNU
                                                               J-H. Choi
                                                Samsung Electronics Co.,
                                                        October 17, 2015

       Transmission of IPv6 Packets over Near Field Communication
                         draft-ietf-6lo-nfc-02

Abstract

   Near field communication (NFC) is a set of standards for smartphones
   and portable devices to establish radio communication with each other
   by touching them together or bringing them into proximity, usually no
   more than 10 cm.  NFC standards cover communications protocols and
   data exchange formats, and are based on existing radio-frequency
   identification (RFID) standards including ISO/IEC 14443 and FeliCa.
   The standards include ISO/IEC 18092 and those defined by the NFC
   Forum.  The NFC technology has been widely implemented and available
   in mobile phones, laptop computers, and many other devices.  This
   document describes how IPv6 is transmitted over NFC using 6LowPAN
   techniques.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 19, 2016.

Hong, et al.             Expires April 19, 2016                 [Page 1]
Internet-Draft                IPv6 over NFC                 October 2015

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Conventions and Terminology . . . . . . . . . . . . . . . . .   4
   3.  Overview of Near Field Communication Technology . . . . . . .   4
     3.1.  Peer-to-peer Mode of NFC  . . . . . . . . . . . . . . . .   4
     3.2.  Protocol Stacks of NFC  . . . . . . . . . . . . . . . . .   5
     3.3.  NFC-enabled Device Addressing . . . . . . . . . . . . . .   6
     3.4.  NFC MAC PDU Size and MTU  . . . . . . . . . . . . . . . .   6
   4.  Specification of IPv6 over NFC  . . . . . . . . . . . . . . .   8
     4.1.  Protocol Stacks . . . . . . . . . . . . . . . . . . . . .   8
     4.2.  Link Model  . . . . . . . . . . . . . . . . . . . . . . .   9
     4.3.  Stateless Address Autoconfiguration . . . . . . . . . . .  10
     4.4.  IPv6 Link Local Address . . . . . . . . . . . . . . . . .  10
     4.5.  Neighbor Discovery  . . . . . . . . . . . . . . . . . . .  11
     4.6.  Dispatch Header . . . . . . . . . . . . . . . . . . . . .  11
     4.7.  Header Compression  . . . . . . . . . . . . . . . . . . .  12
     4.8.  Fragmentation and Reassembly  . . . . . . . . . . . . . .  12
     4.9.  Unicast Address Mapping . . . . . . . . . . . . . . . . .  13
     4.10. Multicast Address Mapping . . . . . . . . . . . . . . . .  13
   5.  Internet Connectivity Scenarios . . . . . . . . . . . . . . .  14
     5.1.  NFC-enabled Device Connected to the Internet  . . . . . .  14
     5.2.  Isolated NFC-enabled Device Network . . . . . . . . . . .  15
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  15
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  15
   8.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  15
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  15
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  15
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  17
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  17

Hong, et al.             Expires April 19, 2016                 [Page 2]
Internet-Draft                IPv6 over NFC                 October 2015

1.  Introduction

   NFC is a set of short-range wireless technologies, typically
   requiring a distance of 10 cm or less.  NFC operates at 13.56 MHz on
   ISO/IEC 18000-3 air interface and at rates ranging from 106 kbit/s to
   424 kbit/s.  NFC always involves an initiator and a target; the
   initiator actively generates an RF field that can power a passive
   target.  This enables NFC targets to take very simple form factors
   such as tags, stickers, key fobs, or cards that do not require
   batteries.  NFC peer-to-peer communication is possible, provided both
   devices are powered.  NFC builds upon RFID systems by allowing two-
   way communication between endpoints, where earlier systems such as
   contactless smart cards were one-way only.  It has been used in
   devices such as mobile phones, running Android operating system,
   named with a feature called "Android Beam".  In addition, it is
   expected for the other mobile phones, running the other operating
   systems (e.g., iOS, etc.) to be equipped with NFC technology in the
   near future.

   Considering the potential for exponential growth in the number of
   heterogeneous air interface technologies, NFC would be widely used as
   one of the other air interface technologies, such as Bluetooth Low
   Energy (BT-LE), Wi-Fi, and so on.  Each of the heterogeneous air
   interface technologies has its own characteristics, which cannot be
   covered by the other technologies, so various kinds of air interface
   technologies would be existing together.  Therefore, it is required
   for them to communicate each other.  NFC also has the strongest point
   (e.g., secure communication distance of 10 cm) to prevent the third
   party from attacking privacy.

   When the number of devices and things having different air interface
   technologies communicate each other, IPv6 is an ideal internet
   protocols owing to its large address space.  Also, NFC would be one
   of the endpoints using IPv6.  Therefore, This document describes how
   IPv6 is transmitted over NFC using 6LoWPAN techiques with following
   scopes.

   o  Overview of NFC technologies;

   o  Specifications for IPv6 over NFC;

      *  Neighbor Discovery;

      *  Addressing and Configuration;

      *  Header Compression;

      *  Fragmentation & Reassembly for a IPv6 datagram;

Hong, et al.             Expires April 19, 2016                 [Page 3]
Internet-Draft                IPv6 over NFC                 October 2015

   RFC4944 [1] specifies the transmission of IPv6 over IEEE 802.15.4.
   The NFC link also has similar characteristics to that of IEEE
   802.15.4.  Many of the mechanisms defined in the RFC4944 [1] can be
   applied to the transmission of IPv6 on NFC links.  This document
   specifies the details of IPv6 transmission over NFC links.

2.  Conventions and Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [2].

3.  Overview of Near Field Communication Technology

   NFC technology enables simple and safe two-way interactions between
   electronic devices, allowing consumers to perform contactless
   transactions, access digital content, and connect electronic devices
   with a single touch.  NFC complements many popular consumer level
   wireless technologies, by utilizing the key elements in existing
   standards for contactless card technology (ISO/IEC 14443 A&B and
   JIS-X 6319-4).  NFC can be compatible with existing contactless card
   infrastructure and it enables a consumer to utilize one device across
   different systems.

   Extending the capability of contactless card technology, NFC also
   enables devices to share information at a distance that is less than
   10 cm with a maximum communication speed of 424 kbps.  Users can
   share business cards, make transactions, access information from a
   smart poster or provide credentials for access control systems with a
   simple touch.

   NFC's bidirectional communication ability is ideal for establishing
   connections with other technologies by the simplicity of touch.  In
   addition to the easy connection and quick transactions, simple data
   sharing is also available.

3.1.  Peer-to-peer Mode of NFC

   NFC-enabled devices are unique in that they can support three modes
   of operation: card emulation, peer-to-peer, and reader/writer.  Peer-
   to-peer mode enables two NFC-enabled devices to communicate with each
   other to exchange information and share files, so that users of NFC-
   enabled devices can quickly share contact information and other files
   with a touch.  Therefore, a NFC-enabled device can securely send IPv6
   packets to any corresponding node on the Internet when a NFC-enabled
   gateway is linked to the Internet.

Hong, et al.             Expires April 19, 2016                 [Page 4]
Internet-Draft                IPv6 over NFC                 October 2015

3.2.  Protocol Stacks of NFC

   The IP protocol can use the services provided by Logical Link Control
   Protocol (LLCP) in the NFC stack to provide reliable, two-way
   transport of information between the peer devices.  Figure 1 depicts
   the NFC P2P protocol stack with IPv6 bindings to the LLCP.

   For data communication in IPv6 over NFC, an IPv6 packet SHALL be
   received at LLCP of NFC and transported to an Information Field in
   Protocol Data Unit (I PDU) of LLCP of the NFC-enabled peer device.
   Since LLCP does not support fragmentation and reassembly, upper
   layers SHOULD support fragmentation and reassembly.  For IPv6
   addressing or address configuration, LLCP SHALL provide related
   information, such as link layer addresses, to its upper layer.  LLCP
   to IPv6 protocol Binding SHALL transfer the SSAP and DSAP value to
   the IPv6 over NFC protocol.  SSAP stands for Source Service Access
   Point, which is 6-bit value meaning a kind of Logical Link Control
   (LLC) address, while DSAP means a LLC address of destination NFC-
   enabled device.

      |                                        |
      |                                        |  Application Layer
      |         Upper Layer Protocols          |   Transport Layer
      |                                        |    Network Layer
      |                                        |         |
      +----------------------------------------+ <------------------
      |            IPv6-LLCP Binding           |         |
      +----------------------------------------+        NFC
      |                                        |    Logical Link
      |      Logical Link Control Protocol     |       Layer
      |                 (LLCP)                 |         |
      +----------------------------------------+ <------------------
      |                                        |         |
      |               Activities               |         |
      |            Digital Protocol            |        NFC
      |                                        |      Physical
      +----------------------------------------+       Layer
      |                                        |         |
      |               RF Analog                |         |
      |                                        |         |
      +----------------------------------------+ <------------------

                     Figure 1: Protocol Stacks of NFC

   The LLCP consists of Logical Link Control (LLC) and MAC Mapping.  The
   MAC Mapping integrates an existing RF protocol into the LLCP
   architecture.  The LLC contains three components, such as Link
   Management, Connection-oriented Transport, and Connection-less

Hong, et al.             Expires April 19, 2016                 [Page 5]
Internet-Draft                IPv6 over NFC                 October 2015

   Transport.  The Link Management component is responsible for
   serializing all connection-oriented and connectionless LLC PDU
   (Protocol Data Unit) exchanges and for aggregation and disaggregation
   of small PDUs.  This component also guarantees asynchronous balanced
   mode communication and provides link status supervision by performing
   the symmetry procedure.  The Connection-oriented Transport component
   is responsible for maintaining all connection-oriented data exchanges
   including connection set-up and termination.  The Connectionless
   Transport component is responsible for handling unacknowledged data
   exchanges.

3.3.  NFC-enabled Device Addressing

   NFC-enabled devices are identified by 6-bit LLC address.  In other
   words, Any address SHALL be usable as both an SSAP and a DSAP
   address.  According to NFCForum-TS-LLCP_1.1 [3], address values
   between 0 and 31 (00h - 1Fh) SHALL be reserved for well-known service
   access points for Service Discovery Protocol (SDP).  Address values
   between 32 and 63 (20h - 3Fh) inclusively, SHALL be assigned by the
   local LLC as the result of an upper layer service request.

3.4.  NFC MAC PDU Size and MTU

   As mentioned in Section 3.2, an IPv6 packet SHALL be received at LLCP
   of NFC and transported to an Unnumbered Information Protocol Data
   Unit (UI PDU) and an Information Field in Protocol Data Unit (I PDU)
   of LLCP of the NFC-enabled peer device.  The format of the UI PDU and
   I PDU SHALL be as shown in Figure 2 and Figure 3.

      0      0    1      1
      0      6    0      6
     +------+----+------+-------------------------------------------+
     |DDDDDD|1100|SSSSSS|             Service Data Unit             |
     +------+----+------+-------------------------------------------+
     | <-- 2 bytes ---> |                                           |
     | <------------------- 128 ~ 2176 bytes ---------------------> |
     |                                                              |

                   Figure 2: Format of the UI PDU in NFC

Hong, et al.             Expires April 19, 2016                 [Page 6]
Internet-Draft                IPv6 over NFC                 October 2015

      0      0    1      1    2    2
      0      6    0      6    0    4
     +------+----+------+----+----+---------------------------------+
     |DDDDDD|1100|SSSSSS|N(S)|N(R)|       Service Data Unit         |
     +------+----+------+----+----+---------------------------------+
     | <------- 3 bytes --------> |                                 |
     | <------------------- 128 ~ 2176 bytes ---------------------> |
     |                                                              |

                   Figure 3: Format of the I PDU in NFC

   The I PDU sequence field SHALL contain two sequence numbers: The send
   sequence number N(S) and the receive sequence number N(R).  The send
   sequence number N(S) SHALL indicate the sequence number associated
   with this I PDU.  The receive sequence number N(R) value SHALL
   indicate that I PDUs numbered up through N(R) - 1 have been received
   correctly by the sender of this I PDU and successfully passed to the
   senders SAP identified in the SSAP field.  These I PDUs SHALL be
   considered as acknowledged.

   The information field of an I PDU SHALL contain a single service data
   unit.  The maximum number of octets in the information field SHALL be
   determined by the Maximum Information Unit (MIU) for the data link
   connection.  The default value of the MIU for I PDUs SHALL be 128
   octets.  The local and remote LLCs each establish and maintain
   distinct MIU values for each data link connection endpoint.  Also, An
   LLC MAY announce a larger MIU for a data link connection by
   transmitting an MIUX extension parameter within the information
   field.  If no MIUX parameter is transmitted, the default MIU value of
   128 SHALL be used.  Otherwise, the MTU size in NFC LLCP SHALL
   calculate the MIU value as follows:

                             MIU = 128 + MIUX.

   According to NFCForum-TS-LLCP_1.1 [3], format of the MIUX parameter
   TLV is as shown in Figure 4.

                    0        0        1    2          3
                    0        8        6    2          1
                   +--------+--------+----------------+
                   |  Type  | Length |     Value      |
                   +--------+--------+----+-----------+
                   |00000010|00000010|1011|    MIUX   |
                   +--------+--------+----+-----------+
                                          | <-------> |
                                          0x000 ~ 0x7FF

                Figure 4: Format of the MIUX Parameter TLV

Hong, et al.             Expires April 19, 2016                 [Page 7]
Internet-Draft                IPv6 over NFC                 October 2015

   When the MIUX parameter is encoded as a TLV, the TLV Type field SHALL
   be 0x02 and the TLV Length field SHALL be 0x02.  The MIUX parameter
   SHALL be encoded into the least significant 11 bits of the TLV Value
   field.  The unused bits in the TLV Value field SHALL be set to zero
   by the sender and SHALL be ignored by the receiver.  However, a
   maximun value of the TLV Value field can be 0x7FF, and a maximum size
   of the MTU in NFC LLCP SHALL calculate 2176 bytes.

4.  Specification of IPv6 over NFC

   NFC technology sets also has considerations and requirements owing to
   low power consumption and allowed protocol overhead. 6LoWPAN
   standards RFC4944 [1], RFC6775 [4], and RFC6282 [5] provide useful
   functionality for reducing overhead which can be applied to BT-LE.
   This functionality comprises of link-local IPv6 addresses and
   stateless IPv6 address auto-configuration (see Section 4.3), Neighbor
   Discovery (see Section 4.5) and header compression (see Section 4.7).

   One of the differences between IEEE 802.15.4 and NFC is that the
   former supports both star and mesh topology (and requires a routing
   protocol), whereas NFC can support direct peer-to-peer connection and
   simple mesh-like topology depending on NFC application scenarios
   because of very short RF distance of 10 cm or less.

4.1.  Protocol Stacks

   Figure 5 illustrates IPv6 over NFC.  Upper layer protocols can be
   transport protocols (TCP and UDP), application layer, and the others
   capable running on the top of IPv6.

Hong, et al.             Expires April 19, 2016                 [Page 8]
Internet-Draft                IPv6 over NFC                 October 2015

      |                                        |     Transport &
      |         Upper Layer Protocols          |  Application Layer
      +----------------------------------------+ <------------------
      |                                        |         |
      |                 IPv6                   |         |
      |                                        |      Network
      +----------------------------------------+       Layer
      |   Adaptation Layer for IPv6 over NFC   |         |
      +----------------------------------------+ <------------------
      |            IPv6-LLCP Binding                     |
      |      Logical Link Control Protocol     |   NFC Link Layer
      |                 (LLCP)                 |         |
      +----------------------------------------+ <------------------
      |                                        |         |
      |               Activities               |        NFC
      |            Digital Protocol            |   Physical Layer
      |               RF Analog                |         |
      |                                        |         |
      +----------------------------------------+ <------------------

                Figure 5: Protocol Stacks for IPv6 over NFC

   Adaptation layer for IPv6 over NFC SHALL support neighbor discovery,
   address auto-configuration, header compression, and fragmentation &
   reassembly.

4.2.  Link Model

   In the case of BT-LE, Logical Link Control and Adaptation Protocol
   (L2CAP) supports fragmentation and reassembly (FAR) functionality;
   therefore, adaptation layer for IPv6 over BT-LE does not have to
   conduct the FAR procedure.  The NFC LLCP, by contrast, does not
   support the FAR functionality, so IPv6 over NFC needs to consider the
   FAR functionality, defined in RFC4944 [1].  However, MTU on NFC link
   can be configured in a connection procedure and extended enough to
   fit the MTU of IPv6 packet.

   The NFC link between two communicating devices is considered to be a
   point-to-point link only.  Unlike in BT-LE, NFC link does not
   consider star topology and mesh network topology but peer-to-peer
   topology and simple multi-hop topology.  Due to this characteristics,
   6LoWPAN functionality, such as addressing and auto-configuration, and
   header compression, is specialized into NFC.

Hong, et al.             Expires April 19, 2016                 [Page 9]
Internet-Draft                IPv6 over NFC                 October 2015

4.3.  Stateless Address Autoconfiguration

   A NFC-enabled device (i.e., 6LN) performs stateless address
   autoconfiguration as per RFC4862 [6].  A 64-bit Interface identifier
   (IID) for a NFC interface MAY be formed by utilizing the 6-bit NFC
   LLCP address (i.e., SSAP or DSAP) (see Section 3.3).  In the
   viewpoint of address configuration, such an IID MAY guarantee a
   stable IPv6 address because each data link connection is uniquely
   identified by the pair of DSAP and SSAP included in the header of
   each LLC PDU in NFC.

   Following the guidance of RFC7136 [10], interface Identifiers of all
   unicast addresses for NFC-enabled devices are formed on the basis of
   64 bits long and constructed in a modified EUI-64 format as shown in
   Figure 6.

   0                1                3                4          5    6
   0                6                2                8          8    3
  +----------------+----------------+----------------+----------+------+
  |0000000000000000|0000000011111111|1111111000000000|0000000000| SSAP |
  +----------------+----------------+----------------+----------+------+

        Figure 6: Formation of IID from NFC-enabled device adddress

   In addition, the "Universal/Local" bit in the case of NFC-enabled
   device address MUST be set to 0 RFC4291 [7].

4.4.  IPv6 Link Local Address

   Only if the NFC-enabled device address is known to be a public
   address the "Universal/Local" bit can be set to 1.  The IPv6 link-
   local address for a NFC-enabled device is formed by appending the
   IID, to the prefix FE80::/64, as depicted in Figure 7.

        0          0                  0                          1
        0          1                  6                          2
        0          0                  4                          7
       +----------+------------------+----------------------------+
       |1111111010|       zeros      |    Interface Identifier    |
       +----------+------------------+----------------------------+
       |                                                          |
       | <---------------------- 128 bits ----------------------> |
       |                                                          |

                 Figure 7: IPv6 link-local address in NFC

Hong, et al.             Expires April 19, 2016                [Page 10]
Internet-Draft                IPv6 over NFC                 October 2015

   The tool for a 6LBR to obtain an IPv6 prefix for numbering the NFC
   network is can be accomplished via DHCPv6 Prefix Delegation (RFC3633
   [8]).

4.5.  Neighbor Discovery

   Neighbor Discovery Optimization for 6LoWPANs (RFC6775 [4]) describes
   the neighbor discovery approach in several 6LoWPAN topologies, such
   as mesh topology.  NFC does not consider complicated mesh topology
   but simple multi-hop network topology or directly connected peer-to-
   peer network.  Therefore, the following aspects of RFC6775 are
   applicable to NFC:

   1.  In a case that a NFC-enabled device (6LN) is directly connected
       to 6LBR, A NFC 6LN MUST register its address with the 6LBR by
       sending a Neighbor Solicitation (NS) message with the Address
       Registration Option (ARO) and process the Neighbor Advertisement
       (NA) accordingly.  In addition, DHCPv6 is used to assigned an
       address, Duplicate Address Detection (DAD) is not required.

   2.  For sending Router Solicitations and processing Router
       Advertisements the NFC 6LNs MUST follow Sections 5.3 and 5.4 of
       the RFC6775.

4.6.  Dispatch Header

   All IPv6-over-NFC encapsulated datagrams transmitted over NFC are
   prefixed by an encapsulation header stack consisting of a Dispatch
   value followed by zero or more header fields.  The only sequence
   currently defined for IPv6-over-NFC is the LOWPAN_IPHC header
   followed by payload, as depicted in Figure 8.

             +---------------+---------------+--------------+
             | IPHC Dispatch |  IPHC Header  |    Payload   |
             +---------------+---------------+--------------+

    Figure 8: A IPv6-over-NFC Encapsulated 6LOWPAN_IPHC Compressed IPv6
                                 Datagram

   The dispatch value may be treated as an unstructured namespace.  Only
   a single pattern is used to represent current LoBAC functionality.

Hong, et al.             Expires April 19, 2016                [Page 11]
Internet-Draft                IPv6 over NFC                 October 2015

              +------------+--------------------+-----------+
              |  Pattern   | Header Type        | Reference |
              +------------+--------------------+-----------+
              | 01  1xxxxx | 6LOWPAN_IPHC       | [RFC6282] |
              +------------+--------------------+-----------+

                         Figure 9: Dispatch Values

   Other IANA-assigned 6LoWPAN Dispatch values do not apply to this
   specification.

4.7.  Header Compression

   Header compression as defined in RFC6282 [5] , which specifies the
   compression format for IPv6 datagrams on top of IEEE 802.15.4, is
   REQUIRED in this document as the basis for IPv6 header compression on
   top of NFC.  All headers MUST be compressed according to RFC6282
   encoding formats.

   Therefore, IPv6 header compression in RFC6282 [5] MUST be
   implemented.  Further, implementations MAY also support Generic
   Header Compression (GHC) of RFC7400 [11].  A node implementing GHC
   MUST probe its peers for GHC support before applying GHC.

   If a 16-bit address is required as a short address of IEEE 802.15.4,
   it MUST be formed by padding the 6-bit NFC link-layer (node) address
   to the left with zeros as shown in Figure 10.

                      0                   1
                      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                     | Padding(all zeros)| NFC Addr. |
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 10: NFC short adress format

4.8.  Fragmentation and Reassembly

   NFC provides fragmentation and reassembly (FAR) for payloads from 128
   bytes up to 2176 bytes as mention in Section 3.4.  The MTU of a
   general IPv6 packet can fit into a sigle NFC link frame.  Therefore,
   the FAR functionality as defined in RFC4944, which specifies the
   fragmentation methods for IPv6 datagrams on top of IEEE 802.15.4, is
   NOT REQUIRED in this document as the basis for IPv6 datagram FAR on
   top of NFC.  The NFC link connection for IPv6 over NFC MUST be
   configured with an equivalent MIU size to fit the MTU of IPv6 Packet.
   However, the default configuration of MIUX value is 0x480 in order to
   fit the MTU (1280 bytes) of a IPv6 packet.

Hong, et al.             Expires April 19, 2016                [Page 12]
Internet-Draft                IPv6 over NFC                 October 2015

4.9.  Unicast Address Mapping

   The address resolution procedure for mapping IPv6 non-multicast
   addresses into NFC link-layer addresses follows the general
   description in Section 7.2 of RFC4861 [9], unless otherwise
   specified.

   The Source/Target link-layer Address option has the following form
   when the addresses are 6-bit NFC link-layer (node) addresses.

                      0                   1
                      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                     |      Type     |   Length=1    |
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                     |                               |
                     +-     Padding (all zeros)     -+
                     |                               |
                     +-                  +-+-+-+-+-+-+
                     |                   | NFC Addr. |
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 11: Unicast address mapping

   Option fields:

      Type:

         1: for Source Link-layer address.

         2: for Target Link-layer address.

      Length:

         This is the length of this option (including the type and
         length fields) in units of 8 octets.  The value of this field
         is 1 for 6-bit NFC node addresses.

      NFC address:

         The 6-bit address in canonical bit order.  This is the unicast
         address the interface currently responds to.

4.10.  Multicast Address Mapping

   All IPv6 multicast packets MUST be sent to NFC Destination Address,
   0x3F (broadcast) and filtered at the IPv6 layer.  When represented as
   a 16-bit address in a compressed header, it MUST be formed by padding

Hong, et al.             Expires April 19, 2016                [Page 13]
Internet-Draft                IPv6 over NFC                 October 2015

   on the left with a zero.  In addition, the NFC Destination Address,
   0x3F, MUST not be used as a unicast NFC address of SSAP or DSAP.

                      0                   1
                      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                     | Padding(all zeros)|1 1 1 1 1 1|
                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                   Figure 12: Multicast address mapping

5.  Internet Connectivity Scenarios

   As two typical scenarios, the NFC network can be isolated and
   connected to the Internet.

5.1.  NFC-enabled Device Connected to the Internet

   One of the key applications by using adaptation technology of IPv6
   over NFC is the most securely transmitting IPv6 packets because RF
   distance between 6LN and 6LBR SHOULD be within 10 cm.  If any third
   party wants to hack into the RF between them, it MUST come to nearly
   touch them.  Applications can choose which kinds of air interfaces
   (e.g., BT-LE, Wi-Fi, NFC, etc.) to send data depending
   characteristics of data.  NFC SHALL be the best solution for secured
   and private information.

   Figure 13 illustrates an example of NFC-enabled device network
   connected to the Internet.  Distance between 6LN and 6LBR SHOULD be
   10 cm or less.  If there is any of close laptop computers to a user,
   it SHALL becomes the 6LBR.  Additionally, When the user mounts a NFC-
   enabled air interface adapter (e.g., portable small NFC dongle) on
   the close laptop PC, the user's NFC-enabled device (6LN) can
   communicate the laptop PC (6LBR) within 10 cm distance.

                                           ************
         6LN ------------------- 6LBR -----* Internet *------- CN
          |  (dis. 10 cm or less)  |       ************         |
          |                        |                            |
          | <-------- NFC -------> | <----- IPv6 packet ------> |
          | (IPv6 over NFC packet) |                            |

      Figure 13: NFC-enabled device network connected to the Internet

Hong, et al.             Expires April 19, 2016                [Page 14]
Internet-Draft                IPv6 over NFC                 October 2015

5.2.  Isolated NFC-enabled Device Network

   In some scenarios, the NFC-enabled device network may transiently be
   a simple isolated network as shown in the Figure 14.

         6LN ---------------------- 6LR ---------------------- 6LN
          |     (10 cm or less)      |     (10 cm or less)      |
          |                          |                          |
          | <--------- NFC --------> | <--------- NFC --------> |
          |   (IPv6 over NFC packet) |  (IPv6 over NFC packet)  |

              Figure 14: Isolated NFC-enabled device network

   In mobile phone markets, applications are designed and made by user
   developers.  They may image interesting applications, where three or
   more mobile phones touch or attach each other to accomplish
   outstanding performance.  For instance, three or more mobile phones
   can play multi-channel sound of music together.  In addition,
   attached three or more mobile phones can make an extended banner to
   show longer sentences in a concert hall.

6.  IANA Considerations

   There are no IANA considerations related to this document.

7.  Security Considerations

   The method of deriving Interface Identifiers from 6-bit NFC Link
   layer addresses is intended to preserve global uniqueness when it is
   possible.  Therefore, it is to required to protect from duplication
   through accident or forgery.

8.  Acknowledgements

   We are grateful to the members of the IETF 6lo working group.

   Michael Richardson, Suresh Krishnan, Pascal Thubert, Carsten Bormann,
   and Alexandru Petrescu have provided valuable feedback for this
   draft.

9.  References

9.1.  Normative References

   [1]        Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler,
              "Transmission of IPv6 Packets over IEEE 802.15.4
              Networks", RFC 4944, DOI 10.17487/RFC4944, September 2007,
              <http://www.rfc-editor.org/info/rfc4944>.

Hong, et al.             Expires April 19, 2016                [Page 15]
Internet-Draft                IPv6 over NFC                 October 2015

   [2]        Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [3]        "Logical Link Control Protocol version 1.1", NFC Forum
              Technical Specification , June 2011.

   [4]        Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C.
              Bormann, "Neighbor Discovery Optimization for IPv6 over
              Low-Power Wireless Personal Area Networks (6LoWPANs)",
              RFC 6775, DOI 10.17487/RFC6775, November 2012,
              <http://www.rfc-editor.org/info/rfc6775>.

   [5]        Hui, J., Ed. and P. Thubert, "Compression Format for IPv6
              Datagrams over IEEE 802.15.4-Based Networks", RFC 6282,
              DOI 10.17487/RFC6282, September 2011,
              <http://www.rfc-editor.org/info/rfc6282>.

   [6]        Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862,
              DOI 10.17487/RFC4862, September 2007,
              <http://www.rfc-editor.org/info/rfc4862>.

   [7]        Hinden, R. and S. Deering, "IP Version 6 Addressing
              Architecture", RFC 4291, DOI 10.17487/RFC4291, February
              2006, <http://www.rfc-editor.org/info/rfc4291>.

   [8]        Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic
              Host Configuration Protocol (DHCP) version 6", RFC 3633,
              DOI 10.17487/RFC3633, December 2003,
              <http://www.rfc-editor.org/info/rfc3633>.

   [9]        Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              DOI 10.17487/RFC4861, September 2007,
              <http://www.rfc-editor.org/info/rfc4861>.

   [10]       Carpenter, B. and S. Jiang, "Significance of IPv6
              Interface Identifiers", RFC 7136, DOI 10.17487/RFC7136,
              February 2014, <http://www.rfc-editor.org/info/rfc7136>.

   [11]       Bormann, C., "6LoWPAN-GHC: Generic Header Compression for
              IPv6 over Low-Power Wireless Personal Area Networks
              (6LoWPANs)", RFC 7400, DOI 10.17487/RFC7400, November
              2014, <http://www.rfc-editor.org/info/rfc7400>.

Hong, et al.             Expires April 19, 2016                [Page 16]
Internet-Draft                IPv6 over NFC                 October 2015

9.2.  Informative References

   [12]       "Near Field Communication - Interface and Protocol (NFCIP-
              1) 3rd Ed.", ECMA-340 , June 2013.

Authors' Addresses

   Yong-Geun Hong
   ETRI
   161 Gajeong-Dong Yuseung-Gu
   Daejeon  305-700
   Korea

   Phone: +82 42 860 6557
   Email: yghong@etri.re.kr

   Younghwan Choi
   ETRI
   218 Gajeongno, Yuseong
   Daejeon  305-700
   Korea

   Phone: +82 42 860 1429
   Email: yhc@etri.re.kr

   Joo-Sang Youn
   DONG-EUI University
   176 Eomgwangno Busan_jin_gu
   Busan  614-714
   Korea

   Phone: +82 51 890 1993
   Email: joosang.youn@gmail.com

   Dongkyun Kim
   Kyungpook National University
   80 Daehak-ro, Buk-gu
   Daegu  702-701
   Korea

   Phone: +82 53 950 7571
   Email: dongkyun@knu.ac.kr

Hong, et al.             Expires April 19, 2016                [Page 17]
Internet-Draft                IPv6 over NFC                 October 2015

   JinHyouk Choi
   Samsung Electronics Co.,
   129 Samsung-ro, Youngdong-gu
   Suwon  447-712
   Korea

   Phone: +82 2 2254 0114
   Email: jinchoe@samsung.com

Hong, et al.             Expires April 19, 2016                [Page 18]