Skip to main content

Ethernet-based xDSL multi-pair bonding (G.Bond/Ethernet) MIB
draft-ietf-adslmib-gbond-eth-mib-07

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 6767.
Authors Edward Beili , Moti Morgenstern
Last updated 2012-07-16
RFC stream Internet Engineering Task Force (IETF)
Formats
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd (None)
IESG IESG state Became RFC 6767 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Needs a YES. Needs 10 more YES or NO OBJECTION positions to pass.
Responsible AD Benoît Claise
IESG note
Send notices to adslmib-chairs@tools.ietf.org, scott.baillie@nec.com.au, edward.beili@actelis.com, moti.Morgenstern@ecitele.com, umberto.bonollo@nec.com.au, draft-ietf-adslmib-gbond-eth-mib@tools.ietf.org
draft-ietf-adslmib-gbond-eth-mib-07
Network Working Group                                           E. Beili
Internet-Draft                                          Actelis Networks
Intended status: Standards Track                          M. Morgenstern
Expires: January 17, 2013                                    ECI Telecom
                                                           July 16, 2012

      Ethernet-based xDSL multi-pair bonding (G.Bond/Ethernet) MIB
                draft-ietf-adslmib-gbond-eth-mib-07.txt

Abstract

   This document defines Management Information Base (MIB) module for
   use with network management protocols in TCP/IP based internets.
   This document defines an extension to the GBOND-MIB module with a set
   of objects for managing Ethernet-based multi-pair bonded xDSL
   interfaces, defined in ITU-T recommendation G.998.2.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on January 17, 2013.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as

Beili & Morgenstern     Expires January 17, 2013                [Page 1]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  The Internet-Standard Management Framework . . . . . . . . . .  3
   3.  The Broadband Forum Management Framework for xDSL Bonding  . .  3
   4.  Relation to other MIB modules  . . . . . . . . . . . . . . . .  3
     4.1.  Relationship to Interfaces Group MIB module  . . . . . . .  4
     4.2.  Relationship to G.Bond MIB module  . . . . . . . . . . . .  4
       4.2.1.  BACP-based Discovery . . . . . . . . . . . . . . . . .  4
     4.3.  Relationship to EFM Copper MIB module  . . . . . . . . . .  6
   5.  MIB Structure  . . . . . . . . . . . . . . . . . . . . . . . .  7
     5.1.  Overview . . . . . . . . . . . . . . . . . . . . . . . . .  7
     5.2.  Performance Monitoring . . . . . . . . . . . . . . . . . .  7
     5.3.  Mapping of Broadband Forum TR-159 Managed Objects  . . . .  7
   6.  G.Bond/Ethernet MIB Definitions  . . . . . . . . . . . . . . .  9
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 48
   8.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 49
   9.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 49
   10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 49
     10.1. Normative References . . . . . . . . . . . . . . . . . . . 49
     10.2. Informative References . . . . . . . . . . . . . . . . . . 51

Beili & Morgenstern     Expires January 17, 2013                [Page 2]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

1.  Introduction

   The Ethernet-based xDSL Multi-Pair Bonding, a.k.a.  G.Bond/Ethernet,
   is specified in ITU-T G.998.2 recommendation [G.998.2], which defines
   a method for bonding (or aggregating) of multiple xDSL lines (or
   individual bearer channels in multiple xDSL lines) into a single bi-
   directional logical link, carrying an Ethernet traffic.

   The MIB module, defined in this document, provides G.Bond/Ethernet
   specific objects for the management of G.998.2 bonded interfaces,
   extending the common bonding objects specified in GBOND-MIB
   [I-D.ietf-adslmib-gbond-mib] module.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in RFC
   2119 [RFC2119].

3.  The Broadband Forum Management Framework for xDSL Bonding

   This document makes use of the Broadband Forum technical report
   Management Framework for xDSL Bonding [TR-159], defining a management
   model and a hierarchy of management objects for the bonded xDSL
   interfaces.

4.  Relation to other MIB modules

   This section outlines the relationship of the MIB modules defined in
   this document with other MIB modules described in the relevant RFCs.
   Specifically, the following MIB modules are discussed: Interfaces
   Group MIB (IF-MIB), G.Bond MIB (GBOND-MIB), and EFM Copper MIB (EFM-
   CU-MIB).

Beili & Morgenstern     Expires January 17, 2013                [Page 3]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

4.1.  Relationship to Interfaces Group MIB module

   A G.Bond/Ethernet port is a private case of a bonded multi-pair xDSL
   interface and as such is managed using generic interface management
   objects defined in the IF-MIB [RFC2863].  In particular, an interface
   index (ifIndex) is used to index instances of G.Bond/Ethernet ports,
   as well as xDSL lines/channels, in a managed system.

4.2.  Relationship to G.Bond MIB module

   GBOND-MIB [I-D.ietf-adslmib-gbond-mib] module defines management
   objects common for all bonded multi-pair xDSL interfaces.  In
   particular it describes the bonding management, bonded port and
   channel configuration, handshake-based discovery, initialization
   sequence etc.

   Both GBOND-MIB and G9982-MIB modules are REQUIRED to manage a G.Bond/
   Ethernet port.

4.2.1.  BACP-based Discovery

   All G.998 protocols share a remote Bonding Channel Entity (BCE)
   discovery, using the [G.994.1] handshake (G.hs).  The GBOND-MIB
   module provides an example of an automatic BCE connection to the
   corresponding Generic Bonding Sublayer (GBS) ports of a generic G.998
   multi-port Central Office (CO) device, using the G.hs-based BCE
   discovery.  Amendment 2 to the ITU-T G.998.2 specification
   [G.998.2-Amd2], provides an alternative optional Bonding Aggregation
   Control Protocol (BACP) for in-service discovery, aggregation and
   pair management.

   The following pseudo-code gives the same example of the discovery and
   automatic BCE assignment for a multi-GBS G.Bond/Eth CO device, using
   BACP objects defined in this MIB module, IF-CAP-STACK-MIB and IF-MIB
   modules [Note that automatic BCE assignment is only shown here for
   the purposes of the example.  Fixed BCE pre-assignment, manual
   assignment or auto-assignment using an alternative internal algorithm
   may be chosen by a particular implementation]:

Beili & Morgenstern     Expires January 17, 2013                [Page 4]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   // Go over all GBS ports in the CO device
   FOREACH gbs[i] IN CO_device
   { // Perform discovery and auto-assignment on GBS ports
     // with room for more Channels
     IF ( gbs[i].NumBCEs < gbs[i].BondCapacity )
     { IF ( gbs[i].g9982OperCp == cpBACP )
       { // Using BACP

         // Get Eligible Group ID and Remote Group ID
         // from a connected BCE (during BACP
         // initialization each BCE is connected to its own GBS)
         gid = ifStackTable[gbs[i]].bce[0].g9982BceEligibleGroupID;
         rgid =
           ifStackTable[gbs[i]].bce[0].g9982BcePeerEligibleGroupID;

         // Go over all disconnected Channels, which can
         // potentially be connected to the GBS
         FOREACH bce[j] IN ifCapStackTable[gbs[i]] AND
                      NOT IN ifStackTable[gbs[i]]  // not connected
         { // Read the Remote Group ID for the selected BCE
           // and compare it with the Remote Group ID of the connected
           // BCE.
           r = bce[j].g9982BcePeerEligibleGroupID;
           IF ( r == rgid AND gbs[i].NumBCEs < gbs[i].BondCapacity)
           { // Remote RT_device connected via BCE[j] is a peer
             // for GBS[i] and there room for another BCE in the
             // GBS[i] aggregation group (max. Bonding capacity is
             // not reached yet).
             // Connect this BCE to the GBS (via ifStackTable,
             // ifInvStackTable being inverse of ifStackTable is
             // updated automatically, i.e., gbs[i] is auto-added
             // to ifInvStackTable[bce[j]])
             ADD bce[j] TO ifStackTable[gbs[i]];
             gbs[i].NumBCEs = gbs[i].NumBCEs + 1;
           }
         }
         // At this point we have discovered all local BCEs which
         // are physically connected to the same remote RT_device
         // and connected them to GBS[i]. Go to the next GBS.
         BREAK;
       }
       ELSE
       { // Use default G.hs discovery protocol
         ...
       }
     }
   }

Beili & Morgenstern     Expires January 17, 2013                [Page 5]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   An SNMP Agent for a G.Bond device builds ifCapStackTable and its
   inverse ifInvCapStackTable on device initialization, according to the
   cross-connect capabilities of the device.  When BACP is used, the
   g9982BceConfEligibleGroupID object identifying bonding eligibility
   MUST be automatically updated, whenever the ifCapStackTable/
   ifInvCapStackTable are changed.

4.3.  Relationship to EFM Copper MIB module

   EFM-CU-MIB [RFC5066] module defines objects for managing Ethernet in
   the First Mile Copper (EFMCu) interfaces 10PASS-TS and 2BASE-TL,
   defined in IEEE Std 802.3-2005 [802.3].  These interfaces are based
   on Single-pair High-speed Digital Subscriber Line (SHDSL) [G.991.2]
   and Very High speed Digital Subscriber Line (VDSL) [G.993.1]
   technology respectively, and can be optionally aggregated (bonded).

   ITU-T G.998.2 specification extends the IEEE 802.3 Clause 61 bonding
   to work over any xDSL technology, providing the ability to bond
   individual channels as well as physical lines.  It also allows the
   use of alternative HDLC encapsulation instead of the default 64/
   65-octet encapsulation and adds a new optional Bonding Aggregation
   Control Protocol (BACP) for in-service discovery, aggregation and
   pair management instead of the default G.hs-based bonding protocol,
   which cannot be used in-service, while the link is up.

   EFM-CU-MIB can be used to manage all aspects of the EFMCu physical
   interfaces (PHYs), including a complete (within the scope of the
   802.3 standard) management of the SHDSL/VDSL lines.  GBOND-MIB and
   G9982-MIB modules on the other hand, provide management objects only
   for the bonding part, leaving the management of the individual xDSL
   interfaces (lines/channels) to the respective xDSL-LINE-MIB modules.

   Therefore an IEEE 802.3 2BASE-TL/10PASS-TS interface can be managed
   by either combination of the following MIB modules:

      IF-MIB + IF-CAP-STACK-MIB + EtherLike-MIB + MAU-MIB + EFM-CU-MIB

      IF-MIB + IF-CAP-STACK-MIB + GBOND-MIB + G9982-MIB + HDSL2-SHDSL-
      LINE-MIB/VDSL-LINE-MIB

   Note also that while EFM-CU-MIB relies on ifMauMediaAvailable object
   from MAU-MIB [RFC4836] for the additional bonded xDSL-specific
   operational states, GBOND-MIB provides these indication via
   gBondPortStatOperStatus object, complementing the ifOperStatus object
   from IF-MIB.

   Finally, EFM-CU-MIB does not include historical Performance
   Monitoring (PM), while GBOND-MIB/GBOND-MIB-ETH/xDSL-LINE-MIB

Beili & Morgenstern     Expires January 17, 2013                [Page 6]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   combination provides full PM functionality for a bonded link and
   individual xDSL lines.

5.  MIB Structure

5.1.  Overview

   The main management objects defined in the G9982-MIB module are split
   into 2 groups, structured as recommended by RFC 4181 [RFC4181]:

   o  g9982Port - containing objects for configuration, capabilities,
      status and PM of G.Bond/Eth ports.  Note that the rest of the
      objects for the Generic Bonded Sub-layer (GBS) port configuration,
      capabilities, status, notifications and PM, is located in the
      GBOND-MIB module.

   o  g9982Bce - containing objects representing OPTIONAL status
      information and BACP configuration for each Bonding Channel Entity
      (BCE).  Note that the rest of the objects for the BCE
      configuration, capabilities, status and notifications, is located
      in relevant xDSL line MIB modules as well as in the GBOND-MIB
      module.

5.2.  Performance Monitoring

   The OPTIONAL performance monitoring counters, thresholds and history
   buckets (interval-counters), similar to those defined in [TR-159] are
   implemented using the textual conventions defined in the HC-PerfHist-
   TC-MIB [RFC3705].  The HC-PerfHist-TC-MIB defines 64-bit versions of
   the textual conventions found in PerfHist-TC-MIB [RFC3593].

   The agent SHOULD align the beginning of each interval to a fifteen
   minute boundary of a wall clock.  Likewise, the beginning of each one
   day intervals SHOULD be aligned with the start of a day.

   Counters are not reset when a GBS is reinitialized, but rather only
   when the agent is reset or reinitialized.

5.3.  Mapping of Broadband Forum TR-159 Managed Objects

   This section contains the mapping between relevant managed objects
   (attributes) defined in [TR-159] and managed objects defined in this
   document.

Beili & Morgenstern     Expires January 17, 2013                [Page 7]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   +---------------------------------+---------------------------------+
   | TR-159 Managed Object           | Corresponding SNMP Object       |
   +---------------------------------+---------------------------------+
   | oBondEth - Basic Package        |                                 |
   | (Mandatory)                     |                                 |
   +---------------------------------+---------------------------------+
   | aEthBACPSupported               | g9982PortCapBacpSupported       |
   +---------------------------------+---------------------------------+
   | aEthTcAdminType                 | g9982PortConfTcAdminType        |
   +---------------------------------+---------------------------------+
   | aEthTcOperType                  | g9982PortStatTcOperType         |
   +---------------------------------+---------------------------------+
   | aEthTcTypesSupported            | g9982PortCapTcTypesSupported    |
   +---------------------------------+---------------------------------+
   | aEthRxErrors                    | g9982PortStatRxErrors           |
   +---------------------------------+---------------------------------+
   | aEthRxSmallFragments            | g9982PortStatRxSmallFragments   |
   +---------------------------------+---------------------------------+
   | aEthRxLargeFragments            | g9982PortStatRxLargeFragments   |
   +---------------------------------+---------------------------------+
   | aEthRxBadFragments              | g9982PortStatRxBadFragments     |
   +---------------------------------+---------------------------------+
   | aEthRxLostFragments             | g9982PortStatRxLostFragments    |
   +---------------------------------+---------------------------------+
   | aEthRxLostStarts                | g9982PortStatRxLostStarts       |
   +---------------------------------+---------------------------------+
   | aEthRxLostEnds                  | g9982PortStatRxLostEnds         |
   +---------------------------------+---------------------------------+
   | aEthRxOverflows                 | g9982PortStatRxOverflows        |
   +---------------------------------+---------------------------------+
   | oBondEth - BACP Package         |                                 |
   | (Optional)                      |                                 |
   +---------------------------------+---------------------------------+
   | aEthAdminCP                     | g9982PortConfAdminCp            |
   +---------------------------------+---------------------------------+
   | aEthOperCP                      | g9982PortStatOperCp             |
   +---------------------------------+---------------------------------+
   | oChannel - BACP package         |                                 |
   | (Optional)                      |                                 |
   +---------------------------------+---------------------------------+
   | aChannelEligibleGroupID         | g9982BceConfEligibleGroupID     |
   +---------------------------------+---------------------------------+
   | aChannelEligibleStreamID        | g9982BceConfPeerEligibleGroupID |
   +---------------------------------+---------------------------------+
   | oChannel - PM package           |                                 |
   | (Optional)                      |                                 |
   +---------------------------------+---------------------------------+
   | aChannelPtmTcRxCodingViolations | g9982BceStatTcInCodingErrors    |

Beili & Morgenstern     Expires January 17, 2013                [Page 8]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   | aChannelPtmTcRxCrcErrors        | g9982BceStatTcInCrcErrors       |
   +---------------------------------+---------------------------------+

                Table 1: Mapping of TR-159 Managed Objects

   Note that some of the mapping between the objects defined in TR-159
   and the ones defined in this MIB module is not one-to-one, for
   example, while TR-159 PM attributes aGroupPerf* map to the
   corresponding gBondPortPm* objects of the GBOND-MIB module, there are
   no dedicated PM attributes for the g9982PortPm* objects introduced in
   this MIB module.  However, since their definition is identical to the
   definition of gBondPortPm* objects of the GBOND-MIB module, we can
   map g9982PortPm* to the relevant aGroupPerf* attributes of TR-159 and
   use the term 'partial mapping' to denote the fact that this mapping
   is not one-to-one.

6.  G.Bond/Ethernet MIB Definitions

G9982-MIB DEFINITIONS ::= BEGIN

  IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    Counter32,
    mib-2,
    Unsigned32
      FROM SNMPv2-SMI         -- [RFC2578]
    TEXTUAL-CONVENTION,
    TruthValue,
    PhysAddress
      FROM SNMPv2-TC          -- [RFC2579]
    MODULE-COMPLIANCE,
    OBJECT-GROUP
      FROM SNMPv2-CONF        -- [RFC2580]
    ifIndex
      FROM IF-MIB             -- [RFC2863]
    HCPerfCurrentCount,
    HCPerfValidIntervals,
    HCPerfInvalidIntervals,
    HCPerfTimeElapsed
      FROM  HC-PerfHist-TC-MIB  -- [RFC3705]
    ;
------------------------------------------------------------------------
  g9982MIB MODULE-IDENTITY
    LAST-UPDATED "201203120000Z"  -- Mar 12, 2012
    ORGANIZATION "IETF ADSL MIB Working Group"
    CONTACT-INFO
      "WG charter:

Beili & Morgenstern     Expires January 17, 2013                [Page 9]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

        http://www.ietf.org/html.charters/adslmib-charter.html

      Mailing Lists:
        General Discussion: adslmib@ietf.org
        To Subscribe: adslmib-request@ietf.org
        In Body: subscribe your_email_address

       Chair: Menachem Dodge
      Postal: ECI Telecom, Ltd.
              30 Hasivim St.,
              Petach-Tikva 4951169
              Israel
       Phone: +972-3-926-8421
       EMail: menachem.dodge@ecitele.com

      Editor: Edward Beili
      Postal: Actelis Networks, Inc.
              25 Bazel St., P.O.B. 10173
              Petach-Tikva 49103
              Israel
       Phone: +972-3-924-3491
       EMail: edward.beili@actelis.com

      Editor: Moti Morgenstern
      Postal: ECI Telecom
              30 Hasivim St.
              Petach-Tikva 4951169
              Israel
       Phone: +972-3-926-6258
       EMail: moti.morgenstern@ecitele.com"

    DESCRIPTION
      "The objects in this MIB module are used to manage the
      Ethernet-based multi-pair bonded xDSL Interfaces, defined in
      ITU-T recommendation G.998.2 (G.Bond/Ethernet).

      This MIB module MUST be used in conjunction with GBOND-MIB
      module, common to all G.Bond technologies.

      The following references are used throughout this MIB module:

      [G.998.2] refers to:
        ITU-T Recommendation G.998.2: 'Ethernet-based multi-pair
        bonding', January 2005.

      [G.998.2-Amd2] refers to:
        ITU-T G.998.2 Amendment 2, December 2007

Beili & Morgenstern     Expires January 17, 2013               [Page 10]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

      [802.3] refers to:
        IEEE Std 802.3-2005: 'IEEE Standard for Information
        technology - Telecommunications and information exchange
        between systems - Local and metropolitan area networks -
        Specific requirements -
        Part 3: Carrier Sense Multiple Access with Collision
        Detection (CSMA/CD) Access Method and Physical Layer
        Specifications', December 2005.

      [TR-159] refers to:
        Broadband Forum Technical Report: 'Management Framework for
        xDSL Bonding', December 2008.

      Naming Conventions:
        BACP   - Bonding Aggregation Control Protocol
        BCE    - Bonding Channel Entity
        BTU    - Bonding Transmission Unit
        BTU-C  - Bonding Transmission Unit, CO side
        BTU-R  - Bonding Transmission Unit, Remote Terminal (CPE) side
        CO     - Central Office
        CPE    - Customer Premises Equipment
        GBS    - Generic Bonding Sublayer
        HDLC   - High-level Data Link Control
        PTM-TC - Packet Transfer Mode Transmission Convergence
                 (sub-layer)
        SNR    - Signal to Noise Ratio
        TC     - Transmission Convergence (sub-layer)
        UAS    - Unavailable Seconds

      Copyright (C) The IETF Trust (2012).
      This version of this MIB module is part of RFC YYYY;
      see the RFC itself for full legal notices."

    REVISION    "201203120000Z"  -- Mar 12, 2012
    DESCRIPTION "Initial version, published as RFC YYYY."

      -- EdNote: Replace YYYY with the actual RFC number &
      -- remove this note.

    ::= { mib-2 ZZZ }

      -- EdNote: Replace ZZZ with a real OID once it is
      -- allocated & remove this note.

   -- Sections of the module
   -- Structured as recommended by [RFC4181], Appendix D

   g9982Objects     OBJECT IDENTIFIER ::= { g9982MIB 1 }

Beili & Morgenstern     Expires January 17, 2013               [Page 11]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   g9982Conformance OBJECT IDENTIFIER ::= { g9982MIB 2 }

   -- Groups in the module

   g9982Port        OBJECT IDENTIFIER ::= { g9982Objects 1 }

   g9982Bce         OBJECT IDENTIFIER ::= { g9982Objects 2 }

   -------------------------------
   -- Textual Conventions
   -------------------------------

   G9982PtmTcType ::= TEXTUAL-CONVENTION
     STATUS       current
     DESCRIPTION
       "This textual convention represents possible PTM-TC types in
       G.bond/Eth ports. The following values are defined:
         tc6465         - 64/65-octet encapsulation, as defined in
                          [802.3] Clause 61.3.3
         tcHDLC         - HDLC encapsulation, as defined in [G.998.2]
                          Annex B"
     SYNTAX      INTEGER {
       tc6465(1),
       tcHDLC(2)
     }

   G9982CpType ::= TEXTUAL-CONVENTION
     STATUS       current
     DESCRIPTION
       "This textual convention represents possible Control Protocol
       types in G.bond/Eth ports. The following values are defined:
         unknown      - the Control Protocol cannot be determined.
         cpHS         - G.hs-based discovery and aggregation,
                        as specified in [G.998.2]
         cpBACP       - Bonding Aggregation Control Protocol (BACP) -
                        a frame-based discovery, aggregation and link
                        management protocol, as specified in
                        [G.998.2-Amd2] Annex C."
     SYNTAX      INTEGER {
       unknown(0),
       cpHS(1),
       cpBACP(2)
     }

   -------------------------------
   -- GBS Notifications group
   -------------------------------

Beili & Morgenstern     Expires January 17, 2013               [Page 12]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     -- empty --

   -------------------------------
   -- GBS group
   -------------------------------

   g9982PortConfTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982PortConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Configuration of G.Bond/Eth GBS ports. Entries in
       this table MUST be maintained in a persistent manner"
     ::= { g9982Port 1 }

   g9982PortConfEntry OBJECT-TYPE
     SYNTAX      G9982PortConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth Port Configuration table.
       Each entry represents a G.Bond Ethernet port indexed by the
       ifIndex.
       Note that a G.Bond/Eth GBS port runs on top of a single
       or multiple BCE port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { g9982PortConfTable 1 }

   G9982PortConfEntry ::=
     SEQUENCE {
       g9982PortConfTcAdminType         G9982PtmTcType,
       g9982PortConfAdminCp             G9982CpType
     }

   g9982PortConfTcAdminType  OBJECT-TYPE
     SYNTAX      G9982PtmTcType
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Administrative (desired) PTM-TC encapsulation type of
       G.Bond/Eth port (GBS).
       Possible values are:
         tc6465(1)  - 64/65-octet encapsulation
         tcHDLC(2)  - HDLC encapsulation
       Attempts to set a port to a non-supported PTM-TC encapsulation
       type (see g9982PortCapTcTypesSupported) SHALL be rejected
       (with the error inconsistentValue).

Beili & Morgenstern     Expires January 17, 2013               [Page 13]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       Changing g9982PortConfTcAdminType is a traffic disruptive
       operation and as such SHALL be done when the link (GBS) is
       administratively 'down', as indicated by the ifAdminStatus object
       in IF-MIB.
       Attempts to change this object SHALL be rejected (with the error
       inconsistentValue) if the link is Up or Initializing.

       This object maps to the TR-159 attribute aEthTcAdminType."
     REFERENCE
       "[TR-159] 5.5.3.4; IF-MIB, ifAdminStatus"
     ::= { g9982PortConfEntry 1 }

   g9982PortConfAdminCp  OBJECT-TYPE
     SYNTAX      G9982CpType
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Administrative (desired) bonding control protocol of
       G.Bond/Eth port (GBS). Possible values are:
         cpHS(1)    - use G.hs-based protocol (default)
         cpBACP(2)  - use frame-based BACP
       Note G.hs-based protocol support is mandatory, according to
       [G.998.2]. Attempts to set a port to a non-supported bonding
       control protocol (e.g. BACP if the value of
       g9982PortCapBacpSupported is false) SHALL be rejected
       (with the error inconsistentValue).

       Changing g9982PortConfAdminCp is a traffic disruptive
       operation and as such SHALL be done when the link (GBS) is
       administratively 'down', as indicated by the ifAdminStatus
       object in IF-MIB.
       Attempts to change this object SHALL be rejected (with the error
       inconsistentValue) if the link is Up or Initializing.

       This object maps to the TR-159 attribute aEthAdminCP."
     REFERENCE
       "[TR-159] 5.5.3.2; IF-MIB, ifAdminStatus"
     DEFVAL { cpHS }
     ::= { g9982PortConfEntry 2 }

   g9982PortCapTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982PortCapEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Capabilities of G.Bond/Eth Ports. Entries in this
       table MUST be maintained in a persistent manner"

Beili & Morgenstern     Expires January 17, 2013               [Page 14]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     ::= { g9982Port 2 }

   g9982PortCapEntry OBJECT-TYPE
     SYNTAX      G9982PortCapEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth Port Capability table.
       Each entry represents a G.Bond port indexed by the ifIndex.
       Note that a G.Bond GBS port runs on top of a single
       or multiple BCE port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { g9982PortCapTable 1 }

   G9982PortCapEntry ::=
     SEQUENCE {
       g9982PortCapTcTypesSupported         BITS,
       g9982PortCapBacpSupported            TruthValue
     }

   g9982PortCapTcTypesSupported  OBJECT-TYPE
     SYNTAX      BITS {
       tc6465(0),
       tcHDLC(1)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "PTM-TC Encapsulation types supported by the G.Bond/Eth port.
       This is a bitmap of possible encapsulation types. The various
       bit positions are:
         tc6465   - GBS is capable of 64/65-octet encapsulation
         tcHDLC   - GBS is capable of HDLC encapsulation

       A desired encapsulation is determined by
       g9982PortConfTcAdminType, while g9982PortStatTcOperType
       reflects the current operating mode.

       This object maps to the TR-159 attribute aEthTcTypesSupported."
     REFERENCE
       "[TR-159] 5.5.3.6"
     ::= { g9982PortCapEntry 1 }

   g9982PortCapBacpSupported  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION

Beili & Morgenstern     Expires January 17, 2013               [Page 15]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       "Indicates whether Bonding Aggregation Control Protocol
       (BACP) - frame-based discovery, aggregation and link management
       protocol specified in [G.998.2-Amd2]) is supported by the
       G.Bond/Ethernet port.
       A value of true(1) indicates that the BACP is supported.
       A value of false(2) indicates that the BACP is unsupported.

       The BACP functionality, if supported, can be enabled or
       disabled via g9982AdminCP, while g9982OperCP
       reflects the current BACP operating mode.

       This object maps to the TR-159 attribute aEthBACPSupported."
     REFERENCE
       "[TR-159] 5.5.3.1, [G.998.2-Amd2] Annex C"
     ::= { g9982PortCapEntry 2 }

   g9982PortStatTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982PortStatEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table provides overall status information of G.Bond
       ports, complementing the generic status information from the
       ifTable of IF-MIB. Additional status information about
       connected BCEs is available from the relevant line MIBs

       This table contains live data from the equipment. As such,
       it is NOT persistent."
     ::= { g9982Port 3 }

   g9982PortStatEntry OBJECT-TYPE
     SYNTAX      G9982PortStatEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth Port Status table.
       Each entry represents a G.Bond/Eth port indexed by the
       ifIndex.
       Note that a G.Bond GBS port runs on top of a single
       or multiple BCE port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { g9982PortStatTable 1 }

   G9982PortStatEntry ::=
     SEQUENCE {
       g9982PortStatTcOperType            G9982PtmTcType,
       g9982PortStatOperCp                G9982CpType,

Beili & Morgenstern     Expires January 17, 2013               [Page 16]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982PortStatRxErrors              Counter32,
       g9982PortStatRxSmallFragments      Counter32,
       g9982PortStatRxLargeFragments      Counter32,
       g9982PortStatRxBadFragments        Counter32,
       g9982PortStatRxLostFragments       Counter32,
       g9982PortStatRxLostStarts          Counter32,
       g9982PortStatRxLostEnds            Counter32,
       g9982PortStatRxOverflows           Counter32
     }

   g9982PortStatTcOperType  OBJECT-TYPE
     SYNTAX      G9982PtmTcType
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Current operational encapsulation type of the G.Bond/Eth
       port.
       Possible values are:
         tc6465(1)   - GBS uses 64/65-octet encapsulation
         tcHDLC(2)   - GBS uses HDLC encapsulation

       The operational PTM-TC encapsulation type can be configured
       via g9982PortConfTcAdminType.

       This objects maps to the TR-159 attribute aEthTcOperType."
     REFERENCE
       "[TR-159] 5.5.3.5"
     ::= { g9982PortStatEntry 1 }

   g9982PortStatOperCp  OBJECT-TYPE
     SYNTAX      G9982CpType
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Current operational bonding discovery and aggregation control
       protocol of the G.Bond/Eth port.
       Possible values are:
         unknown(0)  - the protocol cannot be determined, e.g. when
                       the GBS is down
         cpHS(1)     - GBS uses G.hs-based protocol
         cpBACP(2)   - GBS uses frame-based BACP

       The operational discovery and aggregation control protocol can
       be configured via g9982PortConfAdminCp variable.

       This objects maps to the TR-159 attribute aEthOperCP."
     REFERENCE
       "[TR-159] 5.5.3.3"

Beili & Morgenstern     Expires January 17, 2013               [Page 17]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     ::= { g9982PortStatEntry 2 }

   g9982PortStatRxErrors OBJECT-TYPE
     SYNTAX      Counter32
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of Ethernet frame fragments that have been received
       by the bonding finction and discarded due to various errors.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxErrors."
     REFERENCE
       "[TR-159] 5.5.3.7"
     ::= { g9982PortStatEntry 3 }

   g9982PortStatRxSmallFragments OBJECT-TYPE
     SYNTAX      Counter32
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of fragments smaller than minFragmentSize (64 Bytes),
       that have been received by the bonding function and discarded.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxSmallFragments."
     REFERENCE
       "[TR-159] 5.5.3.8"
     ::= { g9982PortStatEntry 4 }

   g9982PortStatRxLargeFragments OBJECT-TYPE
     SYNTAX      Counter32
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of fragments larger than maxFragmentSize (512 Bytes),
       which have been received by the bonding function and discarded.

Beili & Morgenstern     Expires January 17, 2013               [Page 18]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxLargeFragments."
     REFERENCE
       "[TR-159] 5.5.3.9"
     ::= { g9982PortStatEntry 5 }

   g9982PortStatRxBadFragments OBJECT-TYPE
     SYNTAX      Counter32
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of fragments which do not fit into the sequence
       expected by the frame assembly function, that have been
       received and discarded by the bonding function (the frame buffer
       is flushed to the next valid frame start).

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxBadFragments."
     REFERENCE
       "[TR-159] 5.5.3.10"
     ::= { g9982PortStatEntry 6 }

   g9982PortStatRxLostFragments OBJECT-TYPE
     SYNTAX      Counter32
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of gaps in the sequence of fragments, which have
       been received by the bonding function (the frame buffer is
       flushed to the next valid frame start, when fragment/fragments
       expected by the frame assembly function is/are not received).

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxLostFragments."

Beili & Morgenstern     Expires January 17, 2013               [Page 19]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     REFERENCE
       "[TR-159] 5.5.3.11"
     ::= { g9982PortStatEntry 7 }

   g9982PortStatRxLostStarts OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of missing StartOfPacket indicators expected by the
       frame assembly function.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxLostStarts."
     REFERENCE
       "[TR-159] 5.5.3.12"
     ::= { g9982PortStatEntry 8 }

   g9982PortStatRxLostEnds OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of missing EndOfPacket indicators expected by the
       frame assembly function.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxLostEnds."
     REFERENCE
       "[TR-159] 5.5.3.13"
     ::= { g9982PortStatEntry 9 }

   g9982PortStatRxOverflows OBJECT-TYPE
     SYNTAX      Counter32
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of fragments, received and discarded by the bonding
       function, which would have caused the frame assembly buffer to

Beili & Morgenstern     Expires January 17, 2013               [Page 20]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       overflow.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to the TR-159 attribute aEthRxOverflows."
     REFERENCE
       "[TR-159] 5.5.3.14"
     ::= { g9982PortStatEntry 10 }

   -------------------------------
   -- GBS Performance Monitoring group
   -------------------------------

   g9982PM   OBJECT IDENTIFIER ::= { g9982Port 4 }

   g9982PortPmCurTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982PortPmCurEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains current Performance Monitoring information
       for a G.Bond/ETth port. This table contains live data from the
       equipment and as such is NOT persistent."
     ::= { g9982PM 1 }

   g9982PortPmCurEntry OBJECT-TYPE
     SYNTAX      G9982PortPmCurEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth Port PM table.
       Each entry represents a G.Bond/Eth port indexed by the
       ifIndex."
     INDEX  { ifIndex }
     ::= { g9982PortPmCurTable 1 }

   G9982PortPmCurEntry ::=
     SEQUENCE {
       g9982PortPm15MinValidIntervals      HCPerfValidIntervals,
       g9982PortPm15MinInvalidIntervals    HCPerfInvalidIntervals,
       g9982PortPmCur15MinTimeElapsed      HCPerfTimeElapsed,
       g9982PortPmCur15MinRxErrors         HCPerfCurrentCount,
       g9982PortPmCur15MinRxSmallFragments HCPerfCurrentCount,
       g9982PortPmCur15MinRxLargeFragments HCPerfCurrentCount,
       g9982PortPmCur15MinRxBadFragments   HCPerfCurrentCount,

Beili & Morgenstern     Expires January 17, 2013               [Page 21]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982PortPmCur15MinRxLostFragments  HCPerfCurrentCount,
       g9982PortPmCur15MinRxLostStarts     HCPerfCurrentCount,
       g9982PortPmCur15MinRxLostEnds       HCPerfCurrentCount,
       g9982PortPmCur15MinRxOverflows      HCPerfCurrentCount,
       g9982PortPm1DayValidIntervals       Unsigned32,
       g9982PortPm1DayInvalidIntervals     Unsigned32,
       g9982PortPmCur1DayTimeElapsed       HCPerfTimeElapsed,
       g9982PortPmCur1DayRxErrors          HCPerfCurrentCount,
       g9982PortPmCur1DayRxSmallFragments  HCPerfCurrentCount,
       g9982PortPmCur1DayRxLargeFragments  HCPerfCurrentCount,
       g9982PortPmCur1DayRxBadFragments    HCPerfCurrentCount,
       g9982PortPmCur1DayRxLostFragments   HCPerfCurrentCount,
       g9982PortPmCur1DayRxLostStarts      HCPerfCurrentCount,
       g9982PortPmCur1DayRxLostEnds        HCPerfCurrentCount,
       g9982PortPmCur1DayRxOverflows       HCPerfCurrentCount
     }

   g9982PortPm15MinValidIntervals  OBJECT-TYPE
     SYNTAX      HCPerfValidIntervals
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 15-minute intervals for which the
       performance data was collected. The value of this object will
       be 96 or the maximum number of 15-minute history intervals
       collected by the implementation unless the measurement was
       (re-)started recently, in which case the value will be the
       number of complete 15 minutes intervals for which there are at
       least some data.
       In certain cases it is possible that some intervals are
       unavailable. In this case, this object reports the maximum
       interval number for which data is available.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinValidIntervals."
     REFERENCE
       "[TR-159] 5.5.1.32"
     ::= { g9982PortPmCurEntry 1 }

   g9982PortPm15MinInvalidIntervals  OBJECT-TYPE
     SYNTAX      HCPerfInvalidIntervals
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 15-minute intervals for which the
       performance data was not always available. The value will
       typically be zero except in cases where the data for some
       intervals are not available.

Beili & Morgenstern     Expires January 17, 2013               [Page 22]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinInvalidIntervals."
     REFERENCE
       "[TR-159] 5.5.1.33"
     ::= { g9982PortPmCurEntry 2 }

   g9982PortPmCur15MinTimeElapsed  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds that have elapsed since the
       beginning of the current 15-minute performance interval.

       This object partially maps to the TR-159 attribute
       aGroupPerfCurr15MinTimeElapsed."
     REFERENCE
       "[TR-159] 5.5.1.34"
     ::= { g9982PortPmCurEntry 3 }

   g9982PortPmCur15MinRxErrors  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of errored fragments received and discarded
       by a G.Bond/Eth port, during the current 15-minute performance
       interval.

       Note that the total number of errored fragments is indicated by
       the g9982PortStatRxErrors object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.7"
     ::= { g9982PortPmCurEntry 4}

   g9982PortPmCur15MinRxSmallFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments smaller than minFragmentSize
       (64 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the current 15-minute performance

Beili & Morgenstern     Expires January 17, 2013               [Page 23]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxSmallFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.8"
     ::= { g9982PortPmCurEntry 5}

   g9982PortPmCur15MinRxLargeFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments larger than maxFragmentSize
       (512 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the current 15-minute performance
       interval.

       Note that the total number of large fragments is indicated by
       the g9982PortStatRxLargeFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.9"
     ::= { g9982PortPmCurEntry 6}

   g9982PortPmCur15MinRxBadFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments which do not fit into the
       sequence expected by the frame assembly function, that have been
       received and discarded by a G.Bond/Eth port, during the current
       15-minute performance interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxBadFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.10"
     ::= { g9982PortPmCurEntry 7}

Beili & Morgenstern     Expires January 17, 2013               [Page 24]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   g9982PortPmCur15MinRxLostFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of gaps in the sequence of fragments,
       expected by the frame assembly function of a G.Bond/Eth port,
       during the current 15-minute performance interval.

       Note that the total number of the lost fragments is indicated by
       the g9982PortStatRxLostFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.11"
     ::= { g9982PortPmCurEntry 8}

   g9982PortPmCur15MinRxLostStarts  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing StartOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       current 15-minute performance interval.

       Note that the total number of missing StartOfPacket indicators
       is indicated by the g9982PortStatRxLostStarts object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.12"
     ::= { g9982PortPmCurEntry 9}

   g9982PortPmCur15MinRxLostEnds  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing EndOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       current 15-minute performance interval.

       Note that the total number of missing EndOfPacket indicators
       is indicated by the g9982PortStatRxLostEnds object.

       This object is inhibited during Unavailable Seconds (UAS)."

Beili & Morgenstern     Expires January 17, 2013               [Page 25]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     REFERENCE
       "[TR-159] 5.5.3.13"
     ::= { g9982PortPmCurEntry 10}

   g9982PortPmCur15MinRxOverflows  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments that have been received and
       discarded by a G.Bond/Eth port, which would have caused the
       frame assembly buffer to overflow, during the current 15-minute
       performance interval.

       Note that the total number of fragments which would have caused
       the frame assembly buffer to overflow is indicated by the
       g9982PortStatRxOverflows object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.14"
     ::= { g9982PortPmCurEntry 11}

   g9982PortPm1DayValidIntervals  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..7)
     UNITS       "days"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 1-day intervals for which data was
       collected. The value of this object will be 7 or the maximum
       number of 1-day history intervals collected by the
       implementation unless the measurement was (re-)started recently,
       in which case the value will be the number of complete 1-day
       intervals for which there are at least some data.
       In certain cases it is possible that some intervals are
       unavailable. In this case, this object reports the maximum
       interval number for which data is available."
     REFERENCE
       "[TR-159] 5.5.1.45"
     ::= { g9982PortPmCurEntry 12 }

   g9982PortPm1DayInvalidIntervals  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..7)
     UNITS       "days"
     MAX-ACCESS  read-only
     STATUS      current

Beili & Morgenstern     Expires January 17, 2013               [Page 26]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     DESCRIPTION
       "A read-only number of 1-day intervals for which data was
       not always available. The value will typically be zero except in
       cases where the data for some intervals are not available."
     REFERENCE
       "[TR-159] 5.5.1.46"
     ::= { g9982PortPmCurEntry 13 }

   g9982PortPmCur1DayTimeElapsed  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds that have elapsed since the
       beginning of the current 1-day performance interval."
     REFERENCE
       "[TR-159] 5.5.1.47"
     ::= { g9982PortPmCurEntry 14 }

   g9982PortPmCur1DayRxErrors  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of errored fragments received and discarded
       by a G.Bond/Eth port, during the current 1-day performance
       interval.

       Note that the total number of errored fragments is indicated by
       the g9982PortStatRxErrors object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.7"
     ::= { g9982PortPmCurEntry 15 }

   g9982PortPmCur1DayRxSmallFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments smaller than minFragmentSize
       (64 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the current 1-day performance interval.

Beili & Morgenstern     Expires January 17, 2013               [Page 27]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxSmallFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.8"
     ::= { g9982PortPmCurEntry 16}

   g9982PortPmCur1DayRxLargeFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments larger than maxFragmentSize
       (512 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the current 1-day performance interval.

       Note that the total number of large fragments is indicated by
       the g9982PortStatRxLargeFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.9"
     ::= { g9982PortPmCurEntry 17}

   g9982PortPmCur1DayRxBadFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments which do not fit into the
       sequence expected by the frame assembly function, that have been
       received and discarded by a G.Bond/Eth port, during the current
       1-day performance interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxBadFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.10"
     ::= { g9982PortPmCurEntry 18}

   g9982PortPmCur1DayRxLostFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"

Beili & Morgenstern     Expires January 17, 2013               [Page 28]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of gaps in the sequence of fragments,
       expected by the frame assembly function of a G.Bond/Eth port,
       during the current 1-day performance interval.

       Note that the total number of the lost fragments is indicated by
       the g9982PortStatRxLostFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.11"
     ::= { g9982PortPmCurEntry 19}

   g9982PortPmCur1DayRxLostStarts  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing StartOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       current 1-day performance interval.

       Note that the total number of missing StartOfPacket indicators
       is indicated by the g9982PortStatRxLostStarts object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.12"
     ::= { g9982PortPmCurEntry 20}

   g9982PortPmCur1DayRxLostEnds  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing EndOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       current 1-day performance interval.

       Note that the total number of missing EndOfPacket indicators
       is indicated by the g9982PortStatRxLostEnds object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.13"
     ::= { g9982PortPmCurEntry 21}

Beili & Morgenstern     Expires January 17, 2013               [Page 29]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   g9982PortPmCur1DayRxOverflows  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments that have been received and
       discarded by a G.Bond/Eth port, which would have caused the
       frame assembly buffer to overflow, during the current 1-day
       performance interval.

       Note that the total number of fragments which would have caused
       the frame assembly buffer to overflow is indicated by the
       g9982PortStatRxOverflows object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.14"
     ::= { g9982PortPmCurEntry 22}

   -- Port PM history: 15-min buckets

   g9982PortPm15MinTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982PortPm15MinEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains historical 15-minute buckets of Performance
       Monitoring information for a G.Bond/Eth port (a row for each
       15-minute interval, up to 96 intervals).
       Entries in this table MUST be maintained in a persistent manner."
     ::= { g9982PM 2 }

   g9982PortPm15MinEntry OBJECT-TYPE
     SYNTAX      G9982PortPm15MinEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth Port historical 15-minute PM table.
       Each entry represents performance monitoring data for a
       G.Bond/Eth port, indexed by ifIndex, collected during a
       particular 15-minute interval, indexed by
       g9982PortPm15MinIntervalIndex."
     INDEX  { ifIndex, g9982PortPm15MinIntervalIndex }
     ::= { g9982PortPm15MinTable 1 }

   G9982PortPm15MinEntry ::=
     SEQUENCE {

Beili & Morgenstern     Expires January 17, 2013               [Page 30]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982PortPm15MinIntervalIndex            Unsigned32,
       g9982PortPm15MinIntervalMoniTime         HCPerfTimeElapsed,
       g9982PortPm15MinIntervalRxErrors         HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxSmallFragments HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxLargeFragments HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxBadFragments   HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxLostFragments  HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxLostStarts     HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxLostEnds       HCPerfCurrentCount,
       g9982PortPm15MinIntervalRxOverflows      HCPerfCurrentCount,
       g9982PortPm15MinIntervalValid            TruthValue
     }

   g9982PortPm15MinIntervalIndex  OBJECT-TYPE
     SYNTAX      Unsigned32 (1..96)
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Performance Data Interval number. 1 is the most recent previous
       interval; interval 96 is 24 hours ago.
       Intervals 2..96 are OPTIONAL.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinIntervalNumber."
     REFERENCE
       "[TR-159] 5.5.1.57"
     ::= { g9982PortPm15MinEntry 1 }

   g9982PortPm15MinIntervalMoniTime  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds over which the performance data
       was actually monitored. This value will be the same as the
       interval duration (900 seconds), except in a situation where
       performance data could not be collected for any reason."
     ::= { g9982PortPm15MinEntry 2 }

   g9982PortPm15MinIntervalRxErrors  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of errored fragments received and discarded
       by a G.Bond/Eth port, during the 15-minute performance history

Beili & Morgenstern     Expires January 17, 2013               [Page 31]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       interval.

       Note that the total number of errored fragments is indicated by
       the g9982PortStatRxErrors object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.7"
     ::= { g9982PortPm15MinEntry 3}

   g9982PortPm15MinIntervalRxSmallFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments smaller than minFragmentSize
       (64 Bytes), that have been received and discarded by a
        G.Bond/Eth port, during the 15-minute performance history
        interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxSmallFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.8"
     ::= { g9982PortPm15MinEntry 4}

   g9982PortPm15MinIntervalRxLargeFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments larger than maxFragmentSize
       (512 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the 15-minute performance history
       interval.

       Note that the total number of large fragments is indicated by
       the g9982PortStatRxLargeFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.9"
     ::= { g9982PortPm15MinEntry 5}

Beili & Morgenstern     Expires January 17, 2013               [Page 32]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   g9982PortPm15MinIntervalRxBadFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments which do not fit into the
       sequence expected by the frame assembly function, that have been
       received and discarded by a G.Bond/Eth port, during the 15-minute
       performance history interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxBadFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.10"
     ::= { g9982PortPm15MinEntry 6}

   g9982PortPm15MinIntervalRxLostFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of gaps in the sequence of fragments,
       expected by the frame assembly function of a G.Bond/Eth port,
       during the 15-minute performance history interval.

       Note that the total number of the lost fragments is indicated by
       the g9982PortStatRxLostFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.11"
     ::= { g9982PortPm15MinEntry 7}

   g9982PortPm15MinIntervalRxLostStarts  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing StartOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       15-minute performance history interval.

       Note that the total number of missing StartOfPacket indicators
       is indicated by the g9982PortStatRxLostStarts object.

Beili & Morgenstern     Expires January 17, 2013               [Page 33]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.12"
     ::= { g9982PortPm15MinEntry 8}

   g9982PortPm15MinIntervalRxLostEnds  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing EndOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       15-minute performance history interval.

       Note that the total number of missing EndOfPacket indicators
       is indicated by the g9982PortStatRxLostEnds object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.13"
     ::= { g9982PortPm15MinEntry 9}

   g9982PortPm15MinIntervalRxOverflows  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments that have been received and
       discarded by a G.Bond/Eth port, which would have caused the
       frame assembly buffer to overflow, during the 15-minute
       performance history interval.

       Note that the total number of fragments which would have caused
       the frame assembly buffer to overflow is indicated by the
       g9982PortStatRxOverflows object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.14"
     ::= { g9982PortPm15MinEntry 10}

   g9982PortPm15MinIntervalValid  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only object indicating whether or not this history

Beili & Morgenstern     Expires January 17, 2013               [Page 34]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       bucket contains valid data. Valid bucket is reported as true(1)
       and invalid bucket as false(2).
       If this history bucket is invalid the BTU MUST NOT produce
       notifications based upon the value of the counters in this
       bucket.
       Note that an implementation may decide not to store invalid
       history buckets in its data base. In such case this object is
       not required as only valid history buckets are available while
       invalid history buckets are simply not in the data base.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinIntervalValid."
     REFERENCE
       "[TR-159] 5.5.1.58"
     ::= { g9982PortPm15MinEntry 11 }

   -- Port PM history: 1-day buckets

   g9982PortPm1DayTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982PortPm1DayEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains historical 1-day buckets of Performance
       Monitoring information for a G.Bond/Eth port (a row for each
       1-day interval, up to 7 intervals).
       Entries in this table MUST be maintained in a persistent manner."
     ::= { g9982PM 3 }

   g9982PortPm1DayEntry OBJECT-TYPE
     SYNTAX      G9982PortPm1DayEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth port historical 1-day PM table.
       Each entry represents performance monitoring data for such port,
       indexed by ifIndex, collected during a particular 1-day
       interval, indexed by g9982PortPm1DayIntervalIndex."
     INDEX  { ifIndex, g9982PortPm1DayIntervalIndex }
     ::= { g9982PortPm1DayTable 1 }

   G9982PortPm1DayEntry ::=
     SEQUENCE {
       g9982PortPm1DayIntervalIndex             Unsigned32,
       g9982PortPm1DayIntervalMoniTime          HCPerfTimeElapsed,
       g9982PortPm1DayIntervalRxErrors          HCPerfCurrentCount,
       g9982PortPm1DayIntervalRxSmallFragments  HCPerfCurrentCount,
       g9982PortPm1DayIntervalRxLargeFragments  HCPerfCurrentCount,

Beili & Morgenstern     Expires January 17, 2013               [Page 35]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982PortPm1DayIntervalRxBadFragments    HCPerfCurrentCount,
       g9982PortPm1DayIntervalRxLostFragments   HCPerfCurrentCount,
       g9982PortPm1DayIntervalRxLostStarts      HCPerfCurrentCount,
       g9982PortPm1DayIntervalRxLostEnds        HCPerfCurrentCount,
       g9982PortPm1DayIntervalRxOverflows       HCPerfCurrentCount,
       g9982PortPm1DayIntervalValid             TruthValue
     }

   g9982PortPm1DayIntervalIndex  OBJECT-TYPE
     SYNTAX      Unsigned32 (1..7)
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Performance Data Interval number. 1 is the most recent previous
       interval; interval 7 is 7 days ago.
       Intervals 2..7 are OPTIONAL.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalNumber."
     REFERENCE
       "[TR-159] 5.5.1.62"
     ::= { g9982PortPm1DayEntry 1 }

   g9982PortPm1DayIntervalMoniTime  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds over which the performance data
       was actually monitored. This value will be the same as the
       interval duration (86400 seconds), except in a situation where
       performance data could not be collected for any reason.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalMoniSecs."
     REFERENCE
       "[TR-159] 5.5.1.64"
     ::= { g9982PortPm1DayEntry 2 }

   g9982PortPm1DayIntervalRxErrors  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of errored fragments received and discarded
       by a G.Bond/Eth port, during the 1-day performance history

Beili & Morgenstern     Expires January 17, 2013               [Page 36]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       interval.

       Note that the total number of errored fragments is indicated by
       the g9982PortStatRxErrors object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.7"
     ::= { g9982PortPm1DayEntry 3 }

   g9982PortPm1DayIntervalRxSmallFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments smaller than minFragmentSize
       (64 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the 1-day performance history interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxSmallFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.8"
     ::= { g9982PortPm1DayEntry 4}

   g9982PortPm1DayIntervalRxLargeFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments larger than maxFragmentSize
       (512 Bytes), that have been received and discarded by a
       G.Bond/Eth port, during the 1-day performance history interval.

       Note that the total number of large fragments is indicated by
       the g9982PortStatRxLargeFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.9"
     ::= { g9982PortPm1DayEntry 5}

   g9982PortPm1DayIntervalRxBadFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount

Beili & Morgenstern     Expires January 17, 2013               [Page 37]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments which do not fit into the
       sequence expected by the frame assembly function, that have been
       received and discarded by a G.Bond/Eth port, during the 1-day
       performance history interval.

       Note that the total number of small fragments is indicated by
       the g9982PortStatRxBadFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.10"
     ::= { g9982PortPm1DayEntry 6}

   g9982PortPm1DayIntervalRxLostFragments  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of gaps in the sequence of fragments,
       expected by the frame assembly function of a G.Bond/Eth port,
       during the 1-day performance history interval.

       Note that the total number of the lost fragments is indicated by
       the g9982PortStatRxLostFragments object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.11"
     ::= { g9982PortPm1DayEntry 7}

   g9982PortPm1DayIntervalRxLostStarts  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing StartOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       1-day performance history interval.

       Note that the total number of missing StartOfPacket indicators
       is indicated by the g9982PortStatRxLostStarts object.

       This object is inhibited during Unavailable Seconds (UAS)."

Beili & Morgenstern     Expires January 17, 2013               [Page 38]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     REFERENCE
       "[TR-159] 5.5.3.12"
     ::= { g9982PortPm1DayEntry 8}

   g9982PortPm1DayIntervalRxLostEnds  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of missing EndOfPacket indicators expected
       by the frame assembly function of a G.Bond/Eth port, during the
       1-day performance history interval.

       Note that the total number of missing EndOfPacket indicators
       is indicated by the g9982PortStatRxLostEnds object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.13"
     ::= { g9982PortPm1DayEntry 9}

   g9982PortPm1DayIntervalRxOverflows  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "fragments"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of fragments that have been received and
       discarded by a G.Bond/Eth port, which would have caused the
       frame assembly buffer to overflow, during the 1-day performance
       history interval.

       Note that the total number of fragments which would have caused
       the frame assembly buffer to overflow is indicated by the
       g9982PortStatRxOverflows object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.3.14"
     ::= { g9982PortPm1DayEntry 10}

   g9982PortPm1DayIntervalValid  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only object indicating whether or not this history
       bucket contains valid data. Valid bucket is reported as true(1)

Beili & Morgenstern     Expires January 17, 2013               [Page 39]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       and invalid bucket as false(2).
       If this history bucket is invalid the BTU MUST NOT produce
       notifications based upon the value of the counters in this
       bucket.
       Note that an implementation may decide not to store invalid
       history buckets in its data base. In such case this object is
       not required as only valid history buckets are available while
       invalid history buckets are simply not in the data base.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalValid."
     REFERENCE
       "[TR-159] 5.5.1.63"
     ::= { g9982PortPm1DayEntry 11 }

   -------------------------------
   -- BCE group
   -------------------------------

   g9982BceConfTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982BceConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Configuration of G.Bond/Eth specific aspects for the
       Bonding Channel Entity (BCE) ports (modems/channels).

       Entries in this table MUST be maintained in a persistent
       manner."
     ::= { g9982Bce 1 }

   g9982BceConfEntry OBJECT-TYPE
     SYNTAX      G9982BceConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth BCE Configuration table.
       Each entry represents G.998.2-specific aspects of a BCE port
       indexed by the ifIndex. Note that a G.Bond/Eth BCE port can be
       stacked below a single GBS port, also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { g9982BceConfTable 1 }

   G9982BceConfEntry ::=
     SEQUENCE {
       g9982BceConfEligibleGroupID      PhysAddress,
       g9982BceConfPeerEligibleGroupID  PhysAddress
     }

Beili & Morgenstern     Expires January 17, 2013               [Page 40]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   g9982BceConfEligibleGroupID  OBJECT-TYPE
     SYNTAX      PhysAddress (SIZE(0|6))
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "BACP Eligible Group ID of a G.Bond/ETH BCE port.
       A universally unique 6-octet long identifier, used by the
       OPTIONAL BACP, to determine bonding eligibility. When two BCEs
       have the same g9982BceConfEligibleGroupID on a system, they
       are eligible to be aggregated on that system. Typically, all
       BCEs on a BTU-R device would be assigned the same
       g9982BceConfEligibleGroupID, to assert that all of the BCEs
       should be in the same bonded group. BCEs with different
       g9982BceConfEligibleGroupID values MUST NOT be connected to
       the same GBS.
       BCEs with the same g9982BceConfEligibleGroupID MAY be
       connected to different GBS ports.
       This object MUST be instantiated during BACP initialization,
       when every BCE belongs to its own GBS. Attempts to change this
       object MUST be rejected (with the error inconsistentValue),
       if the BCE is aggregated with other BCEs, i.e. more than one BCE
       is connected to the same GBS, or if the BCE in question is not
       eligible to be bonded with other BCEs having the same value
       (e.g. the bonding is limited to a single Line Card and BCEs are
       located on the different Line Cards, or BCEs are the channels of
       the same line).

       Note that bonding eligibility is reflected in the
       ifCapStackTable and its inverse ifInvCapStackTable, and as such
       any modification of g9982BceConfEligibleGroupID MUST be
       reflected in these tables.

       A zero-length octet string SHALL be returned on an attempt to
       read this object on systems not supporting BACP (the value of
       g9982PortCapBacpSupported for the connected GBS is false).

       This object maps to the TR-159 attribute
       aChannelEligibleGroupID."
     REFERENCE
       "[TR-159] 5.5.7.3"
     ::= { g9982BceConfEntry 1 }

   g9982BceConfPeerEligibleGroupID  OBJECT-TYPE
     SYNTAX      PhysAddress (SIZE(0|6))
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "BACP Eligible Group ID of a peer G.Bond/ETH BCE port, most

Beili & Morgenstern     Expires January 17, 2013               [Page 41]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       recently received by the local BCE via Local info TLV BACPDU
       message from the peer BCE.
       A universally unique 6-octet long identifier, used by the
       OPTIONAL BACP, to determine bonding eligibility.
       BCEs with different g9982BceConfPeerEligibleGroupID values
       MUST NOT be connected to the same GBS.
       BCEs with the same g9982BceConfPeerEligibleGroupID MAY be
       connected to different GBS ports.

       A zero-length octet string SHALL be returned on an attempt to
       read this object on systems not supporting BACP (the value of
       g9982PortCapBacpSupported for the connected GBS is false)
       or when no BACPPDUs has been received from the peer BCE.

       This object maps to the G.998.2-Amd2 attribute
       Remote Group ID."
     REFERENCE
       "[G.998.2-Amd2] C.3.1.6"
     ::= { g9982BceConfEntry 2 }

   g9982BceStatTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9982BceStatEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table provides common status information of G.Bond/Eth
       BCE ports.

       This table contains live data from the equipment. As such,
       it is NOT persistent."
     ::= { g9982Bce 2 }

   g9982BceStatEntry OBJECT-TYPE
     SYNTAX      G9982BceStatEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/Eth BCE Status table.
       Each entry represents common aspects of a G.Bond/Eth BCE port
       indexed by the ifIndex. Note that a BCE port can be stacked
       below a single GBS port, also indexed by ifIndex,
       possibly together with other BCE ports."
     INDEX  { ifIndex }
     ::= { g9982BceStatTable 1 }

   G9982BceStatEntry ::=
     SEQUENCE {

Beili & Morgenstern     Expires January 17, 2013               [Page 42]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982BceStatTcInCodingErrors        Counter32,
       g9982BceStatTcInCrcErrors           Counter32
     }

   g9982BceStatTcInCodingErrors OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of PTM-TC encapsulation errors. This counter is
       incremented for each encapsulation error detected by the
       PTM-TC receive function.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to TR-159 attribute
       aChannelPtmTcRxCodingViolations."
     REFERENCE
       "[TR-159] 5.5.7.8"
     ::= { g9982BceStatEntry 1 }

   g9982BceStatTcInCrcErrors OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A number of PTM-TC CRC errors. This counter is incremented
       for each CRC error detected by the PTM-TC receive function.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to TR-159 attribute aChannelPtmTcRxCrcErrors."
     REFERENCE
       "[TR-159] 5.5.7.9"
     ::= { g9982BceStatEntry 2 }

  -------------------------------
  -- Conformance Statements
  -------------------------------

   g9982Groups      OBJECT IDENTIFIER

Beili & Morgenstern     Expires January 17, 2013               [Page 43]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     ::= { g9982Conformance 1 }

   g9982Compliances OBJECT IDENTIFIER
     ::= { g9982Conformance 2 }

   -- Object Groups

   g9982BasicGroup OBJECT-GROUP
     OBJECTS {
       g9982PortCapTcTypesSupported,
       g9982PortCapBacpSupported,
       g9982PortConfTcAdminType,
       g9982PortStatTcOperType,
       g9982PortStatRxErrors,
       g9982PortStatRxSmallFragments,
       g9982PortStatRxLargeFragments,
       g9982PortStatRxBadFragments,
       g9982PortStatRxLostFragments,
       g9982PortStatRxLostStarts,
       g9982PortStatRxLostEnds,
       g9982PortStatRxOverflows,
       g9982BceStatTcInCodingErrors,
       g9982BceStatTcInCrcErrors
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects representing management information
       for G.Bond/Eth GBS ports."
     ::= { g9982Groups 1 }

   g9982BacpGroup OBJECT-GROUP
     OBJECTS {
       g9982PortConfAdminCp,
       g9982PortStatOperCp,
       g9982BceConfEligibleGroupID,
       g9982BceConfPeerEligibleGroupID

     }
     STATUS      current
     DESCRIPTION
       "A collection of objects representing management information
       for the OPTIONAL frame-based Bonding Aggregation Control
       Protocol (BACP) used by G.Bond/Eth GBS ports instead of the
       mandatory G.hs-based discovery and aggregation protocol."
     ::= { g9982Groups 2 }

   g9982BceGroup OBJECT-GROUP
     OBJECTS {

Beili & Morgenstern     Expires January 17, 2013               [Page 44]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982BceStatTcInCodingErrors,
       g9982BceStatTcInCrcErrors
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects representing OPTIONAL management
       information for G.Bond/Eth BCE ports."
     ::= { g9982Groups 3 }

   g9982PerfCurrGroup OBJECT-GROUP
     OBJECTS {
       g9982PortPm15MinValidIntervals,
       g9982PortPm15MinInvalidIntervals,
       g9982PortPmCur15MinTimeElapsed,
       g9982PortPmCur15MinRxErrors,
       g9982PortPmCur15MinRxSmallFragments,
       g9982PortPmCur15MinRxLargeFragments,
       g9982PortPmCur15MinRxBadFragments,
       g9982PortPmCur15MinRxLostFragments,
       g9982PortPmCur15MinRxLostStarts,
       g9982PortPmCur15MinRxLostEnds,
       g9982PortPmCur15MinRxOverflows,
       g9982PortPm1DayValidIntervals,
       g9982PortPm1DayInvalidIntervals,
       g9982PortPmCur1DayTimeElapsed,
       g9982PortPmCur1DayRxErrors,
       g9982PortPmCur1DayRxSmallFragments,
       g9982PortPmCur1DayRxLargeFragments,
       g9982PortPmCur1DayRxBadFragments,
       g9982PortPmCur1DayRxLostFragments,
       g9982PortPmCur1DayRxLostStarts,
       g9982PortPmCur1DayRxLostEnds,
       g9982PortPmCur1DayRxOverflows
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL current Performance
       Monitoring information for G.Bond/Eth ports."
     ::= { g9982Groups 4 }

   g9982Perf15MinGroup OBJECT-GROUP
     OBJECTS {
       g9982PortPm15MinIntervalMoniTime,
       g9982PortPm15MinIntervalRxErrors,
       g9982PortPm15MinIntervalRxSmallFragments,
       g9982PortPm15MinIntervalRxLargeFragments,
       g9982PortPm15MinIntervalRxBadFragments,
       g9982PortPm15MinIntervalRxLostFragments,

Beili & Morgenstern     Expires January 17, 2013               [Page 45]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

       g9982PortPm15MinIntervalRxLostStarts,
       g9982PortPm15MinIntervalRxLostEnds,
       g9982PortPm15MinIntervalRxOverflows,
       g9982PortPm15MinIntervalValid
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL historical
       Performance Monitoring information for G.Bond/Eth ports, during
       previous 15-minute intervals ."
     ::= { g9982Groups 5 }

   g9982Perf1DayGroup OBJECT-GROUP
     OBJECTS {
       g9982PortPm1DayIntervalMoniTime,
       g9982PortPm1DayIntervalRxErrors,
       g9982PortPm1DayIntervalRxSmallFragments,
       g9982PortPm1DayIntervalRxLargeFragments,
       g9982PortPm1DayIntervalRxBadFragments,
       g9982PortPm1DayIntervalRxLostFragments,
       g9982PortPm1DayIntervalRxLostStarts,
       g9982PortPm1DayIntervalRxLostEnds,
       g9982PortPm1DayIntervalRxOverflows,
       g9982PortPm1DayIntervalValid
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL historical
       Performance Monitoring information for G.Bond/Eth ports, during
       previous 1-day intervals ."
     ::= { g9982Groups 6 }

  -------------------------------
  -- Compliance Statements
  -------------------------------

   g9982Compliance MODULE-COMPLIANCE
     STATUS      current
     DESCRIPTION
       "The compliance statement for G.Bond Ethernet interfaces.
       Compliance with the following external compliance statements
       is REQUIRED:

       MIB Module             Compliance Statement
       ----------             --------------------
       IF-MIB                 ifCompliance3
       GBOND-MIB              gBondCompliance"

Beili & Morgenstern     Expires January 17, 2013               [Page 46]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

     MODULE  -- this module
       MANDATORY-GROUPS {
         g9982BasicGroup
       }

       GROUP       g9982BceGroup
       DESCRIPTION
         "Support for this group is OPTIONAL"

       GROUP       g9982BacpGroup
       DESCRIPTION
         "Support for this group is OPTIONAL and only required for
         implementations supporting BACP."

       GROUP       g9982PerfCurrGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting Performance Monitoring."

       GROUP       g9982Perf15MinGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting historical Performance Monitoring."

       GROUP       g9982Perf1DayGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting 1-day historical Performance Monitoring."

       OBJECT      g9982PortCapTcTypesSupported
       SYNTAX      BITS {
         tc6465(0),
         tcHDLC(1)
       }
       DESCRIPTION
         "Support for all TC types is not required. However at least
         one value SHALL be supported"

       OBJECT      g9982PortCapBacpSupported
       SYNTAX      TruthValue
       DESCRIPTION
         "Support for BACP is OPTIONAL, therefore a value of false(2)
         SHALL be supported."

       OBJECT      g9982PortConfTcAdminType
       MIN-ACCESS  read-only
       DESCRIPTION
         "Write access is not required (needed only for GBS

Beili & Morgenstern     Expires January 17, 2013               [Page 47]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

         supporting more than a single TC encapsulation type, i.e.
         tc6465 and tcHDLC."

       OBJECT      g9982PortConfAdminCp
       MIN-ACCESS  read-only
       DESCRIPTION
         "Write access is not required (needed only for GBS
         supporting BACP in addition to mandatory G.hs-based bonding
         discovery and aggregation protocol."

     ::= { g9982Compliances 1 }
END

7.  Security Considerations

   There is a number of managed objects defined in this MIB module with
   a MAX-ACCESS clause of read-write and/or read-create.  Such objects
   may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  Changing of g9982PortConfTable configuration parameters (e.g.
      g9982PortConfTcAdminType) may lead to a complete service
      interruption, in case the specified PTM-TC encapsulation type is
      not supported by the remote end.

   o  Changing of g9982BceConfTable configuration parameters (e.g.
      g9982BceConfEligibleGroupID) may lead to preventing a non-bonded
      BCE from being bonded in any bonding group or false advertisement
      of bonding eligibility (e.g. between BCEs residing on different
      line cards in an application which does not support cross-card
      bonding).

   Some of the readable objects in this MIB module (i.e., those with
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments since, collectively, they
   provide information about the performance of network interfaces and
   can reveal some aspects of their configuration.

   It is thus important to control even GET and/or NOTIFY access to
   these objects and possibly even encrypt the values of these objects
   when sending them over the network via SNMP.  These are the tables
   and objects and their sensitivity/vulnerability:

   o  g9982PortStatTable - objects in this table (e.g.
      g9982PortStatTcOperType) provide status information for the G.Bond

Beili & Morgenstern     Expires January 17, 2013               [Page 48]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

      port, which may aid in deciphering of the G.Bond/ETH
      transmissions.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB module.

   Implementations MUST provide the security features described by the
   SNMPv3 framework (see [RFC3410]), including full support for
   authentication and privacy via the User-based Security Model (USM)
   [RFC3414] with the AES cipher algorithm [RFC3826].  Implementations
   MAY also provide support for the Transport Security Model (TSM)
   [RFC5591] in combination with a secure transport such as SSH
   [RFC5592] or TLS/DTLS [RFC6353].

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

8.  IANA Considerations

   An object identifier for g9982MIB MODULE-IDENTITY SHALL be allocated
   by IANA [1] in the MIB-2 transmission sub-tree, before this document
   is published as an RFC.

9.  Acknowledgments

   This document was produced by the [ADSLMIB] working group.

   Special thanks to Dan Romascanu for his meticulous review of this
   text.

10.  References

10.1.  Normative References

   [802.3]                       IEEE, "IEEE Standard for Information
                                 technology - Telecommunications and
                                 information exchange between systems -
                                 Local and metropolitan area networks -
                                 Specific requirements - Part 3: Carrier
                                 Sense Multiple Access with Collision

Beili & Morgenstern     Expires January 17, 2013               [Page 49]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

                                 Detection (CSMA/CD) Access Method and
                                 Physical Layer Specifications", IEEE
                                 Std 802.3-2005, December 2005.

   [G.998.2]                     ITU-T, "Ethernet-based multi-pair
                                 bonding", ITU-T Recommendation G.998.2,
                                 January 2005, <http://www.itu.int/rec/
                                 T-REC-G.998.2/en>.

   [G.998.2-Amd2]                ITU-T, "Ethernet-based multi-pair
                                 bonding Amendment 2", ITU-T
                                 Recommendation G.998.2/Amd.2,
                                 December 2007, <http://www.itu.int/rec/
                                 T-REC-G.998.2-200712-I!Amd2/en>.

   [I-D.ietf-adslmib-gbond-mib]  Beili, E. and M. Morgenstern, "xDSL
                                 multi-pair bonding (G.Bond) MIB",
                                 draft-ietf-adslmib-gbond-mib-11 (work
                                 in progress), July 2012.

   [RFC2119]                     Bradner, S., "Key words for use in RFCs
                                 to Indicate Requirement Levels",
                                 BCP 14, RFC 2119, March 1997.

   [RFC2578]                     McCloghrie, K., Ed., Perkins, D., Ed.,
                                 and J. Schoenwaelder, Ed., "Structure
                                 of Management Information Version 2
                                 (SMIv2)", STD 58, RFC 2578, April 1999.

   [RFC2579]                     McCloghrie, K., Ed., Perkins, D., Ed.,
                                 and J. Schoenwaelder, Ed., "Textual
                                 Conventions for SMIv2", STD 58,
                                 RFC 2579, April 1999.

   [RFC2580]                     McCloghrie, K., Perkins, D., and J.
                                 Schoenwaelder, "Conformance Statements
                                 for SMIv2", STD 58, RFC 2580,
                                 April 1999.

   [RFC2863]                     McCloghrie, K. and F. Kastenholz, "The
                                 Interfaces Group MIB", RFC 2863,
                                 June 2000.

   [RFC3414]                     Blumenthal, U. and B. Wijnen, "User-
                                 based Security Model (USM) for version
                                 3 of the Simple Network Management
                                 Protocol (SNMPv3)", STD 62, RFC 3414,
                                 December 2002.

Beili & Morgenstern     Expires January 17, 2013               [Page 50]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   [RFC3705]                     Ray, B. and R. Abbi, "High Capacity
                                 Textual Conventions for MIB Modules
                                 Using Performance History Based on 15
                                 Minute Intervals", RFC 3705,
                                 February 2004.

   [RFC3826]                     Blumenthal, U., Maino, F., and K.
                                 McCloghrie, "The Advanced Encryption
                                 Standard (AES) Cipher Algorithm in the
                                 SNMP User-based Security Model",
                                 RFC 3826, June 2004.

   [TR-159]                      Beili, E. and M. Morgenstern,
                                 "Management Framework for xDSL
                                 Bonding", Broadband Forum technical
                                 report TR-159, December 2008.

10.2.  Informative References

   [ADSLMIB]                     IETF, "ADSL MIB (adslmib) Charter", <ht
                                 tp://www.ietf.org/html.charters/
                                 adslmib-charter.html>.

   [G.991.2]                     ITU-T, "Single-pair High-speed Digital
                                 Subscriber Line (SHDSL) transceivers",
                                 ITU-T Recommendation G.991.2,
                                 December 2003, <http://www.itu.int/rec/
                                 T-REC-G.991.2/en>.

   [G.993.1]                     ITU-T, "Very High speed Digital
                                 Subscriber Line transceivers", ITU-T
                                 Recommendation G.993.1, June 2004, <htt
                                 p://www.itu.int/rec/T-REC-G.993.1/en>.

   [G.994.1]                     ITU-T, "Handshake procedures for
                                 digital subscriber line (DSL)
                                 transceivers", ITU-T
                                 Recommendation G.994.1, February 2007,
                                 <http://www.itu.int/rec/T-REC-
                                 G.994.1/en>.

   [RFC3410]                     Case, J., Mundy, R., Partain, D., and
                                 B. Stewart, "Introduction and
                                 Applicability Statements for Internet-
                                 Standard Management Framework",
                                 RFC 3410, December 2002.

   [RFC3593]                     Tesink, K., "Textual Conventions for

Beili & Morgenstern     Expires January 17, 2013               [Page 51]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

                                 MIB Modules Using Performance History
                                 Based on 15 Minute Intervals",
                                 RFC 3593, September 2003.

   [RFC4181]                     Heard, C., "Guidelines for Authors and
                                 Reviewers of MIB Documents", BCP 111,
                                 RFC 4181, September 2005.

   [RFC4836]                     Beili, E., "Definitions of Managed
                                 Objects for IEEE 802.3 Medium
                                 Attachment Units (MAUs)", RFC 4836,
                                 April 2007.

   [RFC5066]                     Beili, E., "Ethernet in the First Mile
                                 Copper (EFMCu) Interfaces MIB",
                                 RFC 5066, November 2007.

   [RFC5591]                     Harrington, D. and W. Hardaker,
                                 "Transport Security Model for the
                                 Simple Network Management Protocol
                                 (SNMP)", RFC 5591, June 2009.

   [RFC5592]                     Harrington, D., Salowey, J., and W.
                                 Hardaker, "Secure Shell Transport Model
                                 for the Simple Network Management
                                 Protocol (SNMP)", RFC 5592, June 2009.

   [RFC6353]                     Hardaker, W., "Transport Layer Security
                                 (TLS) Transport Model for the Simple
                                 Network Management Protocol (SNMP)",
                                 RFC 6353, July 2011.

URIs

   [1]  <http://www.iana.org/>

Authors' Addresses

   Edward Beili
   Actelis Networks
   25 Bazel St.
   Petach-Tikva  49103
   Israel

   Phone: +972-3-924-3491
   EMail: edward.beili@actelis.com

Beili & Morgenstern     Expires January 17, 2013               [Page 52]
Internet-Draft             G.Bond/Ethernet MIB                 July 2012

   Moti Morgenstern
   ECI Telecom
   30 Hasivim St.
   Petach-Tikva  4951169
   Israel

   Phone: +972-3-926-6258
   EMail: moti.morgenstern@ecitele.com

Beili & Morgenstern     Expires January 17, 2013               [Page 53]