Skip to main content

A Generic Autonomic Signaling Protocol (GRASP)
draft-ietf-anima-grasp-07

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8990.
Authors Carsten Bormann , Brian E. Carpenter , Bing Liu
Last updated 2016-09-29 (Latest revision 2016-09-12)
Replaces draft-carpenter-anima-gdn-protocol
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd Sheng Jiang
IESG IESG state Became RFC 8990 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to "Sheng Jiang" <jiangsheng@huawei.com>
draft-ietf-anima-grasp-07
Network Working Group                                         C. Bormann
Internet-Draft                                   Universitaet Bremen TZI
Intended status: Standards Track                       B. Carpenter, Ed.
Expires: March 17, 2017                                Univ. of Auckland
                                                             B. Liu, Ed.
                                            Huawei Technologies Co., Ltd
                                                      September 13, 2016

             A Generic Autonomic Signaling Protocol (GRASP)
                       draft-ietf-anima-grasp-07

Abstract

   This document establishes requirements for a signaling protocol that
   enables autonomic devices and autonomic service agents to dynamically
   discover peers, to synchronize state with them, and to negotiate
   parameter settings mutually with them.  The document then defines a
   general protocol for discovery, synchronization and negotiation,
   while the technical objectives for specific scenarios are to be
   described in separate documents.  An Appendix briefly discusses
   existing protocols with comparable features.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 17, 2017.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of

Bormann, et al.          Expires March 17, 2017                 [Page 1]
Internet-Draft                    GRASP                   September 2016

   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Requirement Analysis of Discovery, Synchronization and
       Negotiation . . . . . . . . . . . . . . . . . . . . . . . . .   4
     2.1.  Requirements for Discovery  . . . . . . . . . . . . . . .   5
     2.2.  Requirements for Synchronization and Negotiation
           Capability  . . . . . . . . . . . . . . . . . . . . . . .   6
     2.3.  Specific Technical Requirements . . . . . . . . . . . . .   8
   3.  GRASP Protocol Overview . . . . . . . . . . . . . . . . . . .  10
     3.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .  10
     3.2.  High-Level Design Choices . . . . . . . . . . . . . . . .  11
     3.3.  GRASP Protocol Basic Properties and Mechanisms  . . . . .  15
       3.3.1.  Required External Security Mechanism  . . . . . . . .  15
       3.3.2.  Limited Security Instances  . . . . . . . . . . . . .  15
       3.3.3.  Transport Layer Usage . . . . . . . . . . . . . . . .  17
       3.3.4.  Discovery Mechanism and Procedures  . . . . . . . . .  18
       3.3.5.  Negotiation Procedures  . . . . . . . . . . . . . . .  21
       3.3.6.  Synchronization and Flooding Procedure  . . . . . . .  22
     3.4.  High Level Deployment Model . . . . . . . . . . . . . . .  24
     3.5.  GRASP Constants . . . . . . . . . . . . . . . . . . . . .  25
     3.6.  Session Identifier (Session ID) . . . . . . . . . . . . .  26
     3.7.  GRASP Messages  . . . . . . . . . . . . . . . . . . . . .  26
       3.7.1.  Message Overview  . . . . . . . . . . . . . . . . . .  26
       3.7.2.  GRASP Message Format  . . . . . . . . . . . . . . . .  27
       3.7.3.  Discovery Message . . . . . . . . . . . . . . . . . .  27
       3.7.4.  Discovery Response Message  . . . . . . . . . . . . .  28
       3.7.5.  Request Messages  . . . . . . . . . . . . . . . . . .  29
       3.7.6.  Negotiation Message . . . . . . . . . . . . . . . . .  30
       3.7.7.  Negotiation End Message . . . . . . . . . . . . . . .  30
       3.7.8.  Confirm Waiting     Message . . . . . . . . . . . . .  31
       3.7.9.  Synchronization Message . . . . . . . . . . . . . . .  31
       3.7.10. Flood Synchronization Message . . . . . . . . . . . .  31
       3.7.11. No Operation Message  . . . . . . . . . . . . . . . .  32
     3.8.  GRASP Options . . . . . . . . . . . . . . . . . . . . . .  33
       3.8.1.  Format of GRASP Options . . . . . . . . . . . . . . .  33
       3.8.2.  Divert Option . . . . . . . . . . . . . . . . . . . .  33
       3.8.3.  Accept Option . . . . . . . . . . . . . . . . . . . .  33
       3.8.4.  Decline Option  . . . . . . . . . . . . . . . . . . .  34
       3.8.5.  Locator Options . . . . . . . . . . . . . . . . . . .  34
     3.9.  Objective Options . . . . . . . . . . . . . . . . . . . .  36

Bormann, et al.          Expires March 17, 2017                 [Page 2]
Internet-Draft                    GRASP                   September 2016

       3.9.1.  Format of Objective Options . . . . . . . . . . . . .  36
       3.9.2.  Objective flags . . . . . . . . . . . . . . . . . . .  37
       3.9.3.  General Considerations for Objective Options  . . . .  37
       3.9.4.  Organizing of Objective Options . . . . . . . . . . .  38
       3.9.5.  Experimental and Example Objective Options  . . . . .  39
   4.  Implementation Status [RFC Editor: please remove] . . . . . .  40
     4.1.  BUPT C++ Implementation . . . . . . . . . . . . . . . . .  40
     4.2.  Python Implementation . . . . . . . . . . . . . . . . . .  40
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  41
   6.  CDDL Specification of GRASP . . . . . . . . . . . . . . . . .  43
   7.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  45
   8.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  47
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  47
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  47
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  48
   Appendix A.  Open Issues  . . . . . . . . . . . . . . . . . . . .  51
   Appendix B.  Closed Issues [RFC Editor: Please remove]  . . . . .  52
   Appendix C.  Change log [RFC Editor: Please remove] . . . . . . .  59
   Appendix D.  Capability Analysis of Current Protocols . . . . . .  63
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  66

1.  Introduction

   The success of the Internet has made IP-based networks bigger and
   more complicated.  Large-scale ISP and enterprise networks have
   become more and more problematic for human based management.  Also,
   operational costs are growing quickly.  Consequently, there are
   increased requirements for autonomic behavior in the networks.
   General aspects of autonomic networks are discussed in [RFC7575] and
   [RFC7576].

   One approach is to largely decentralize the logic of network
   management by migrating it into network elements.  A reference model
   for autonomic networking on this basis is given in
   [I-D.ietf-anima-reference-model].  The reader should consult this
   document to understand how various autonomic components fit together.
   In order to fulfil autonomy, devices that embody Autonomic Service
   Agents (ASAs, [RFC7575]) have specific signaling requirements.  In
   particular they need to discover each other, to synchronize state
   with each other, and to negotiate parameters and resources directly
   with each other.  There is no limitation on the types of parameters
   and resources concerned, which can include very basic information
   needed for addressing and routing, as well as anything else that
   might be configured in a conventional non-autonomic network.  The
   atomic unit of discovery, synchronization or negotiation is referred
   to as a technical objective, i.e, a configurable parameter or set of
   parameters (defined more precisely in Section 3.1).

Bormann, et al.          Expires March 17, 2017                 [Page 3]
Internet-Draft                    GRASP                   September 2016

   Following this Introduction, Section 2 describes the requirements for
   discovery, synchronization and negotiation.  Negotiation is an
   iterative process, requiring multiple message exchanges forming a
   closed loop between the negotiating entities.  In fact, these
   entities are ASAs, normally but not necessarily in different network
   devices.  State synchronization, when needed, can be regarded as a
   special case of negotiation, without iteration.  Section 3.2
   describes a behavior model for a protocol intended to support
   discovery, synchronization and negotiation.  The design of GeneRic
   Autonomic Signaling Protocol (GRASP) in Section 3 of this document is
   mainly based on this behavior model.  The relevant capabilities of
   various existing protocols are reviewed in Appendix D.

   The proposed discovery mechanism is oriented towards synchronization
   and negotiation objectives.  It is based on a neighbor discovery
   process, but also supports diversion to off-link peers.  There is no
   assumption of any particular form of network topology.  When a device
   starts up with no pre-configuration, it has no knowledge of the
   topology.  The protocol itself is capable of being used in a small
   and/or flat network structure such as a small office or home network
   as well as a professionally managed network.  Therefore, the
   discovery mechanism needs to be able to allow a device to bootstrap
   itself without making any prior assumptions about network structure.

   Because GRASP can be used to perform a decision process among
   distributed devices or between networks, it must run in a secure and
   strongly authenticated environment.

   It is understood that in realistic deployments, not all devices will
   support GRASP.  It is expected that some autonomic service agents
   will directly manage a group of non-autonomic nodes, and that other
   non-autonomic nodes will be managed traditionally.  Such mixed
   scenarios are not discussed in this specification.

2.  Requirement Analysis of Discovery, Synchronization and Negotiation

   This section discusses the requirements for discovery, negotiation
   and synchronization capabilities.  The primary user of the protocol
   is an autonomic service agent (ASA), so the requirements are mainly
   expressed as the features needed by an ASA.  A single physical device
   might contain several ASAs, and a single ASA might manage several
   technical objectives.  If a technical objective is managed by several
   ASAs, any necessary coordination is outside the scope of the
   signaling protocol itself.

   Note that requirements for ASAs themselves, such as the processing of
   Intent [RFC7575] or interfaces for coordination between ASAs are out
   of scope for the present document.

Bormann, et al.          Expires March 17, 2017                 [Page 4]
Internet-Draft                    GRASP                   September 2016

2.1.  Requirements for Discovery

   D1.  ASAs may be designed to manage anything, as required in
   Section 2.2.  A basic requirement is therefore that the protocol can
   represent and discover any kind of technical objective among
   arbitrary subsets of participating nodes.

   In an autonomic network we must assume that when a device starts up
   it has no information about any peer devices, the network structure,
   or what specific role it must play.  The ASA(s) inside the device are
   in the same situation.  In some cases, when a new application session
   starts up within a device, the device or ASA may again lack
   information about relevant peers.  For example, it might be necessary
   to set up resources on multiple other devices, coordinated and
   matched to each other so that there is no wasted resource.  Security
   settings might also need updating to allow for the new device or
   user.  The relevant peers may be different for different technical
   objectives.  Therefore discovery needs to be repeated as often as
   necessary to find peers capable of acting as counterparts for each
   objective that a discovery initiator needs to handle.  From this
   background we derive the next three requirements:

   D2.  When an ASA first starts up, it has no knowledge of the specific
   network to which it is attached.  Therefore the discovery process
   must be able to support any network scenario, assuming only that the
   device concerned is bootstrapped from factory condition.

   D3.  When an ASA starts up, it must require no configured location
   information about any peers in order to discover them.

   D4.  If an ASA supports multiple technical objectives, relevant peers
   may be different for different discovery objectives, so discovery
   needs to be performed separately to find counterparts for each
   objective.  Thus, there must be a mechanism by which an ASA can
   separately discover peer ASAs for each of the technical objectives
   that it needs to manage, whenever necessary.

   D5.  Following discovery, an ASA will normally perform negotiation or
   synchronization for the corresponding objectives.  The design should
   allow for this by conveniently linking discovery to negotiation and
   synchronization.  It may provide an optional mechanism to combine
   discovery and negotiation/synchronization in a single call.

   D6.  Some objectives may only be significant on the local link, but
   others may be significant across the routed network and require off-
   link operations.  Thus, the relevant peers might be immediate
   neighbors on the same layer 2 link, or they might be more distant and
   only accessible via layer 3.  The mechanism must therefore provide

Bormann, et al.          Expires March 17, 2017                 [Page 5]
Internet-Draft                    GRASP                   September 2016

   both on-link and off-link discovery of ASAs supporting specific
   technical objectives.

   D7.  The discovery process should be flexible enough to allow for
   special cases, such as the following:

   o  During initialisation, a device must be able to establish mutual
      trust with the rest of the network and join an authentication
      mechanism.  Although this will inevitably start with a discovery
      action, it is a special case precisely because trust is not yet
      established.  This topic is the subject of
      [I-D.ietf-anima-bootstrapping-keyinfra].  We require that once
      trust has been established for a device, all ASAs within the
      device inherit the device's credentials and are also trusted.

   o  Depending on the type of network involved, discovery of other
      central functions might be needed, such as the Network Operations
      Center (NOC) [I-D.ietf-anima-stable-connectivity].  The protocol
      must be capable of supporting such discovery during
      initialisation, as well as discovery during ongoing operation.

   D8.  The discovery process must not generate excessive traffic and
   must take account of sleeping nodes in the case of a constrained-node
   network [RFC7228].

   D9.  There must be a mechanism for handling stale discovery results.

2.2.  Requirements for Synchronization and Negotiation Capability

   As background, consider the example of routing protocols, the closest
   approximation to autonomic networking already in widespread use.
   Routing protocols use a largely autonomic model based on distributed
   devices that communicate repeatedly with each other.  The focus is
   reachability, so current routing protocols mainly consider simple
   link status, i.e., up or down, and an underlying assumption is that
   all nodes need a consistent view of the network topology in order for
   the routing algorithm to converge.  Thus, routing is mainly based on
   information synchronization between peers, rather than on bi-
   directional negotiation.  Other information, such as latency,
   congestion, capacity, and particularly unused capacity, would be
   helpful to get better path selection and utilization rate, but is not
   normally used in distributed routing algorithms.  Additionally,
   autonomic networks need to be able to manage many more dimensions,
   such as security settings, power saving, load balancing, etc.  Status
   information and traffic metrics need to be shared between nodes for
   dynamic adjustment of resources and for monitoring purposes.  While
   this might be achieved by existing protocols when they are available,
   the new protocol needs to be able to support parameter exchange,

Bormann, et al.          Expires March 17, 2017                 [Page 6]
Internet-Draft                    GRASP                   September 2016

   including mutual synchronization, even when no negotiation as such is
   required.  In general, these parameters do not apply to all
   participating nodes, but only to a subset.

   SN1.  A basic requirement for the protocol is therefore the ability
   to represent, discover, synchronize and negotiate almost any kind of
   network parameter among selected subsets of participating nodes.

   SN2.  Negotiation is a request/response process that must be
   guaranteed to terminate (with success or failure) and if necessary it
   must contain tie-breaking rules for each technical objective that
   requires them.  While these must be defined specifically for each use
   case, the protocol should have some general mechanisms in support of
   loop and deadlock prevention, such as hop count limits or timeouts.

   SN3.  Synchronization might concern small groups of nodes or very
   large groups.  Different solutions might be needed at different
   scales.

   SN4.  To avoid "reinventing the wheel", the protocol should be able
   to encapsulate the data formats used by existing configuration
   protocols (such as NETCONF/YANG) in cases where that is convenient.

   SN5.  Human intervention in complex situations is costly and error-
   prone.  Therefore, synchronization or negotiation of parameters
   without human intervention is desirable whenever the coordination of
   multiple devices can improve overall network performance.  It
   therefore follows that the protocol, as part of the Autonomic
   Networking Infrastructure, should be capable of running in any device
   that would otherwise need human intervention.  The issue of running
   in constrained nodes is discussed in
   [I-D.ietf-anima-reference-model].

   SN6.  Human intervention in large networks is often replaced by use
   of a top-down network management system (NMS).  It therefore follows
   that the protocol, as part of the Autonomic Networking
   Infrastructure, should be capable of running in any device that would
   otherwise be managed by an NMS, and that it can co-exist with an NMS,
   and with protocols such as SNMP and NETCONF.

   SN7.  Some features are expected to be implemented by individual
   ASAs, but the protocol must be general enough to allow them:

   o  Dependencies and conflicts: In order to decide a configuration on
      a given device, the device may need information from neighbors.
      This can be established through the negotiation procedure, or
      through synchronization if that is sufficient.  However, a given
      item in a neighbor may depend on other information from its own

Bormann, et al.          Expires March 17, 2017                 [Page 7]
Internet-Draft                    GRASP                   September 2016

      neighbors, which may need another negotiation or synchronization
      procedure to obtain or decide.  Therefore, there are potential
      dependencies and conflicts among negotiation or synchronization
      procedures.  Resolving dependencies and conflicts is a matter for
      the individual ASAs involved.  To allow this, there need to be
      clear boundaries and convergence mechanisms for negotiations.
      Also some mechanisms are needed to avoid loop dependencies.  In
      such a case, the protocol's role is limited to bilateral signaling
      between ASAs.

   o  Recovery from faults and identification of faulty devices should
      be as automatic as possible.  The protocol's role is limited to
      the ability to handle discovery, synchronization and negotiation
      at any time, in case an ASA detects an anomaly such as a
      negotiation counterpart failing.

   o  Since the goal is to minimize human intervention, it is necessary
      that the network can in effect "think ahead" before changing its
      parameters.  One aspect of this is an ASA that relies on a
      knowledge base to predict network behavior.  This is out of scope
      for the signaling protocol.  However, another aspect is
      forecasting the effect of a change by a "dry run" negotiation
      before actually installing the change.  This will be an
      application of the protocol rather than a feature of the protocol
      itself.

   o  Management logging, monitoring, alerts and tools for intervention
      are required.  However, these can only be features of individual
      ASAs.  Another document [I-D.ietf-anima-stable-connectivity]
      discusses how such agents may be linked into conventional OAM
      systems via an Autonomic Control Plane
      [I-D.ietf-anima-autonomic-control-plane].

   SN8.  The protocol will be able to deal with a wide variety of
   technical objectives, covering any type of network parameter.
   Therefore the protocol will need a flexible and easily extensible
   format for describing objectives.  At a later stage it may be
   desirable to adopt an explicit information model.  One consideration
   is whether to adopt an existing information model or to design a new
   one.

2.3.  Specific Technical Requirements

   T1.  It should be convenient for ASA designers to define new
   technical objectives and for programmers to express them, without
   excessive impact on run-time efficiency and footprint.  In
   particular, it should be possible for ASAs to be implemented
   independently of each other as user space programs rather than as

Bormann, et al.          Expires March 17, 2017                 [Page 8]
Internet-Draft                    GRASP                   September 2016

   kernel code.  The classes of device in which the protocol might run
   is discussed in [I-D.ietf-anima-reference-model].

   T2.  The protocol should be easily extensible in case the initially
   defined discovery, synchronization and negotiation mechanisms prove
   to be insufficient.

   T3.  To be a generic platform, the protocol payload format should be
   independent of the transport protocol or IP version.  In particular,
   it should be able to run over IPv6 or IPv4.  However, some functions,
   such as multicasting on a link, might need to be IP version
   dependent.  In case of doubt, IPv6 should be preferred.

   T4.  The protocol must be able to access off-link counterparts via
   routable addresses, i.e., must not be restricted to link-local
   operation.

   T5.  It must also be possible for an external discovery mechanism to
   be used, if appropriate for a given technical objective.  In other
   words, GRASP discovery must not be a prerequisite for GRASP
   negotiation or synchronization.

   T6.  The protocol must be capable of supporting multiple simultaneous
   operations, especially when wait states occur.

   T7.  Intent: There must be provision for general Intent rules to be
   applied by all devices in the network (e.g., security rules, prefix
   length, resource sharing rules).  However, Intent distribution might
   not use the signaling protocol itself, but its design should not
   exclude such use.

   T8.  Management monitoring, alerts and intervention: Devices should
   be able to report to a monitoring system.  Some events must be able
   to generate operator alerts and some provision for emergency
   intervention must be possible (e.g.  to freeze synchronization or
   negotiation in a mis-behaving device).  These features might not use
   the signaling protocol itself, but its design should not exclude such
   use.

   T9.  The protocol needs to be fully secured against forged messages
   and man-in-the middle attacks, and secured as much as reasonably
   possible against denial of service attacks.  It needs to be capable
   of encryption in order to resist unwanted monitoring.  However, it is
   not required that the protocol itself provides these security
   features; it may depend on an existing secure environment.

Bormann, et al.          Expires March 17, 2017                 [Page 9]
Internet-Draft                    GRASP                   September 2016

3.  GRASP Protocol Overview

3.1.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   [RFC2119] when they appear in ALL CAPS.  When these words are not in
   ALL CAPS (such as "should" or "Should"), they have their usual
   English meanings, and are not to be interpreted as [RFC2119] key
   words.

   This document uses terminology defined in [RFC7575].

   The following additional terms are used throughout this document:

   o  Autonomic Device: identical to Autonomic Node.

   o  Discovery: a process by which an ASA discovers peers according to
      a specific discovery objective.  The discovery results may be
      different according to the different discovery objectives.  The
      discovered peers may later be used as negotiation counterparts or
      as sources of synchronization data.

   o  Negotiation: a process by which two ASAs interact iteratively to
      agree on parameter settings that best satisfy the objectives of
      both ASAs.

   o  State Synchronization: a process by which ASAs interact to receive
      the current state of parameter values stored in other ASAs.  This
      is a special case of negotiation in which information is sent but
      the ASAs do not request their peers to change parameter settings.
      All other definitions apply to both negotiation and
      synchronization.

   o  Technical Objective (usually abbreviated as Objective): A
      technical objective is a configurable parameter or set of
      parameters of some kind, which occurs in three contexts:
      Discovery, Negotiation and Synchronization.  In the protocol, an
      objective is represented by an identifier and if relevant a value.
      Normally, a given objective will not occur in negotiation and
      synchronization contexts simultaneously.

      *  One ASA may support multiple independent objectives.

      *  The parameter described by a given objective is naturally based
         on a specific service or function or action.  It may in
         principle be anything that can be set to a specific logical,

Bormann, et al.          Expires March 17, 2017                [Page 10]
Internet-Draft                    GRASP                   September 2016

         numerical or string value, or a more complex data structure, by
         a network node.  That node is generally expected to contain an
         ASA which may itself manage subsidiary non-autonomic nodes.

      *  Discovery Objective: if a node needs to synchronize or
         negotiate a specific objective but does not know a peer that
         supports this objective, it starts a discovery process.  The
         objective is called a Discovery Objective during this process.

      *  Synchronization Objective: an objective whose specific
         technical content needs to be synchronized among two or more
         ASAs.

      *  Negotiation Objective: an objective whose specific technical
         content needs to be decided in coordination with another ASA.

   o  Discovery Initiator: an ASA that spontaneously starts discovery by
      sending a discovery message referring to a specific discovery
      objective.

   o  Discovery Responder: a peer that either contains an ASA supporting
      the discovery objective indicated by the discovery initiator, or
      caches the locator(s) of the ASA(s) supporting the objective.  The
      locator(s) are indicated in a Discovery Response, which is
      normally sent by the protocol kernel, as described later.

   o  Synchronization Initiator: an ASA that spontaneously starts
      synchronization by sending a request message referring to a
      specific synchronization objective.

   o  Synchronization Responder: a peer ASA which responds with the
      value of a synchronization objective.

   o  Negotiation Initiator: an ASA that spontaneously starts
      negotiation by sending a request message referring to a specific
      negotiation objective.

   o  Negotiation Counterpart: a peer with which the Negotiation
      Initiator negotiates a specific negotiation objective.

3.2.  High-Level Design Choices

   This section describes a behavior model and some considerations for
   designing a generic signaling protocol initially supporting
   discovery, synchronization and negotiation, which can act as a
   platform for different technical objectives.

   o  A generic platform

Bormann, et al.          Expires March 17, 2017                [Page 11]
Internet-Draft                    GRASP                   September 2016

      The protocol is designed as a generic platform, which is
      independent from the synchronization or negotiation contents.  It
      takes care of the general intercommunication between counterparts.
      The technical contents will vary according to the various
      technical objectives and the different pairs of counterparts.

   o  The protocol is expected to form part of an Autonomic Networking
      Infrastructure [I-D.ietf-anima-reference-model].  It will provide
      services to ASAs via a suitable application programming interface
      (API), which will reflect the protocol elements but will not
      necessarily be in one-to-one correspondence to them.  This API is
      out of scope for the present document.

   o  It is normally expected that a single main instance of GRASP will
      exist in an autonomic node, and that the protocol engine and each
      ASA will run as independent asynchronous processes.  However,
      separate GRASP instances may exist for security reasons
      (Section 3.3.2).

   o  Security infrastructure and trust relationship

      Because this negotiation protocol may directly cause changes to
      device configurations and bring significant impacts to a running
      network, this protocol is assumed to run within an existing secure
      environment with strong authentication.  As a design choice, the
      protocol itself is not provided with built-in security
      functionality.

      On the other hand, a limited negotiation model might be deployed
      based on a limited trust relationship.  For example, between two
      administrative domains, ASAs might also exchange limited
      information and negotiate some particular configurations based on
      a limited conventional or contractual trust relationship.

   o  Discovery, synchronization and negotiation are designed together.

      The discovery method and the synchronization and negotiation
      methods are designed in the same way and can be combined when this
      is useful.  These processes can also be performed independently
      when appropriate.

      *  GRASP discovery is always available for efficient discovery of
         GRASP peers and allows a rapid mode of operation described in
         Section 3.3.4.  For some objectives, especially those concerned

Bormann, et al.          Expires March 17, 2017                [Page 12]
Internet-Draft                    GRASP                   September 2016

         with application layer services, another discovery mechanism
         such as the future DNS Service Discovery [RFC7558] or Service
         Location Protocol [RFC2608] MAY be used.  The choice is left to
         the designers of individual ASAs.

   o  A uniform pattern for technical contents

      The synchronization and negotiation contents are defined according
      to a uniform pattern.  They could be carried either in simple
      binary format or in payloads described by a flexible language.
      The basic protocol design uses the Concise Binary Object
      Representation (CBOR) [RFC7049].  The format is extensible for
      unknown future requirements.

   o  A flexible model for synchronization

      GRASP supports bilateral synchronization, which could be used to
      perform synchronization among a small number of nodes.  It also
      supports an unsolicited flooding mode when large groups of nodes,
      possibly including all autonomic nodes, need data for the same
      technical objective.

      *  There may be some network parameters for which a more
         traditional flooding mechanism such as DNCP [RFC7787] is
         considered more appropriate.  GRASP can coexist with DNCP.

   o  A simple initiator/responder model for negotiation

      Multi-party negotiations are too complicated to be modeled and
      there might be too many dependencies among the parties to converge
      efficiently.  A simple initiator/responder model is more feasible
      and can complete multi-party negotiations by indirect steps.

   o  Organizing of synchronization or negotiation content

      Naturally, the technical content will be organized according to
      the relevant function or service.  The content from different
      functions or services is kept independent from each other.  They
      are not combined into a single option or single session because
      these contents may be negotiated or synchronized with different
      counterparts or may be different in response time.  Thus a normal
      arrangement would be a single ASA managing a small set of closely
      related objectives, with a version of that ASA in each relevant

Bormann, et al.          Expires March 17, 2017                [Page 13]
Internet-Draft                    GRASP                   September 2016

      autonomic node.  Further discussion of this aspect is out of scope
      for the current document.

   o  Requests and responses in negotiation procedures

      The initiator can negotiate with its relevant negotiation
      counterpart ASAs, which may be different according to the specific
      negotiation objective.  It can request relevant information from
      the negotiation counterpart so that it can decide its local
      configuration to give the most coordinated performance.  It can
      request the negotiation counterpart to make a matching
      configuration in order to set up a successful communication with
      it.  It can request certain simulation or forecast results by
      sending some dry run conditions.

      Beyond the traditional yes/no answer, the responder can reply with
      a suggested alternative value for the objective concerned.  This
      would start a bi-directional negotiation ending in a compromise
      between the two ASAs.

   o  Convergence of negotiation procedures

      To enable convergence, when a responder makes a suggestion of a
      changed condition in a negative reply, it should be as close as
      possible to the original request or previous suggestion.  The
      suggested value of the third or later negotiation steps should be
      chosen between the suggested values from the last two negotiation
      steps.  In any case there must be a mechanism to guarantee
      convergence (or failure) in a small number of steps, such as a
      timeout or maximum number of iterations.

      *  End of negotiation

         A limited number of rounds, for example three, or a timeout, is
         needed on each ASA for each negotiation objective.  It may be
         an implementation choice, a pre-configurable parameter, or
         network Intent.  These choices might vary between different
         types of ASA.  Therefore, the definition of each negotiation
         objective MUST clearly specify this, so that the negotiation
         can always be terminated properly.

      *  Failed negotiation

Bormann, et al.          Expires March 17, 2017                [Page 14]
Internet-Draft                    GRASP                   September 2016

         There must be a well-defined procedure for concluding that a
         negotiation cannot succeed, and if so deciding what happens
         next (deadlock resolution, tie-breaking, or revert to best-
         effort service).  Again, this MUST be specified for individual
         negotiation objectives, as an implementation choice, a pre-
         configurable parameter, or network Intent.

3.3.  GRASP Protocol Basic Properties and Mechanisms

3.3.1.  Required External Security Mechanism

   The protocol SHOULD run within a secure Autonomic Control Plane (ACP)
   [I-D.ietf-anima-autonomic-control-plane].  The ACP is assumed to
   carry all messages securely, including link-local multicast if
   possible.  A GRASP implementation MUST verify whether the ACP is
   operational.

   If there is no ACP, the protocol MUST use another form of strong
   authentication and SHOULD use a form of strong encryption.  TLS
   [RFC5246] is RECOMMENDED for this purpose, based on a local Public
   Key Infrastructure (PKI) [RFC5280] managed within the autonomic
   network itself.  The details of such a PKI and how its boundary is
   established are out of scope for this document.  DTLS [RFC6347] MAY
   be used but since GRASP operations usually involve several messages
   this is not expected to be advantageous.

   The ACP, or in its absence the local PKI, sets the boundary within
   which nodes are trusted as GRASP peers.  A GRASP implementation MUST
   refuse to execute GRASP synchronization and negotiation functions if
   there is neither an operational ACP nor an operational TLS or DTLS
   environment.

   Link-local multicast is used for discovery messages.  Responses to
   discovery messages MUST be secured, with one exception mentioned in
   the next section.

3.3.2.  Limited Security Instances

   This section describes three cases where additional instances of
   GRASP are appropriate.

   1) As mentioned in Section 3.2, some GRASP operations might be
   performed across an administrative domain boundary by mutual
   agreement.  Such operations MUST be confined to a separate instance
   of GRASP with its own copy of all GRASP data structures.  Messages
   MUST be authenticated and SHOULD be encrypted.  TLS is RECOMMENDED
   for this purpose.

Bormann, et al.          Expires March 17, 2017                [Page 15]
Internet-Draft                    GRASP                   September 2016

   2) During initialisation, before a node has joined the applicable
   trust infrastructure, [I-D.ietf-anima-bootstrapping-keyinfra], it is
   impossible to secure messages.  Thus, the security bootstrap process
   needs to use insecure GRASP discovery, response and flood messages.
   Such usage MUST be limited to link-local operations and MUST be
   confined to a separate insecure instance of GRASP with its own copy
   of all GRASP data structures.  This instance is nicknamed DULL -
   Discovery Unsolicited Link Local.

   The detailed rules for the DULL instance of GRASP are as follows:

   o  An initiator MUST only send Discovery or Flood Synchronization
      link-local multicast messages with a loop count of 1.  A responder
      MAY send a Discovery Response message.  Other GRASP message types
      MUST NOT be sent.

   o  A responder MUST silently discard any message whose loop count is
      not 1.

   o  A responder MUST silently discard any message referring to a GRASP
      Objective that is not directly part of the bootstrap creation
      process.

   o  A responder MUST NOT relay any multicast messages.

   o  A Discovery Response MUST indicate a link-local address.

   o  A Discovery Response MUST NOT include a Divert option.

   o  A node MUST silently discard any message whose source address is
      not link-local.

   3) During ACP formation [I-D.ietf-anima-autonomic-control-plane], a
   separate instance of GRASP is used, with unicast messages secured by
   TLS, and with its own copy of all GRASP data structures.  This
   instance is nicknamed SONN - Secure Only Neighbor Negotiation.

   The detailed rules for the SONN instance of GRASP are as follows:

   o  Any type of GRASP message MAY be sent.

   o  An initiator MUST send any Discovery or Flood Synchronization
      link-local multicast messages with a loop count of 1.

   o  A responder MUST silently discard any Discovery or Flood
      Synchronization message whose loop count is not 1.

Bormann, et al.          Expires March 17, 2017                [Page 16]
Internet-Draft                    GRASP                   September 2016

   o  A responder MUST silently discard any message referring to a GRASP
      Objective that is not directly part of the ACP creation process.

   o  A responder MUST NOT relay any multicast messages.

   o  A Discovery Response MUST indicate a link-local address.

   o  A Discovery Response MUST NOT include a Divert option.

   o  A node MUST silently discard any message whose source address is
      not link-local.

3.3.3.  Transport Layer Usage

   GRASP discovery and flooding messages are designed for use over link-
   local multicast UDP.  They MUST NOT be fragmented, and therefore MUST
   NOT exceed the link MTU size.  Nothing in principle prevents them
   from working over some other method of sending packets to all on-link
   neighbors, but this is out of scope for the present specification.

   All other GRASP messages are unicast and could in principle run over
   any transport protocol.  An implementation MUST support use of TCP.
   It MAY support use of another transport protocol.  However, GRASP
   itself does not provide for error detection or retransmission.  Use
   of an unreliable transport protocol is therefore NOT RECOMMENDED.

   Nevertheless, when running within a secure ACP on reliable
   infrastructure, UDP MAY be used for unicast messages not exceeding
   the minimum IPv6 path MTU; however, TCP MUST be used for longer
   messages.  In other words, IPv6 fragmentation is avoided.  If a node
   receives a UDP message but the reply is too long, it MUST open a TCP
   connection to the peer for the reply.  Note that when the network is
   under heavy load or in a fault condition, UDP might become
   unreliable.  Since this is when autonomic functions are most
   necessary, automatic fallback to TCP MUST be implemented.  The
   simplest implementation is therefore to use only TCP.  In particular,
   to guarantee interoperability during bootstrap and startup, using TCP
   for discovery responses is strongly advised.

   When running without an ACP, TLS MUST be supported and used by
   default, except for link-local multicast messages.  DTLS MAY be
   supported as an alternative but the details are out of scope for this
   document.  Transport protocols other than TCP and UDP are also out of
   scope for this document.

   For link-local multicast, the GRASP protocol listens to the well-
   known GRASP Listen Port (Section 3.5).  For unicast transport
   sessions used for discovery responses, synchronization and

Bormann, et al.          Expires March 17, 2017                [Page 17]
Internet-Draft                    GRASP                   September 2016

   negotiation, the ASA concerned normally listens on its own
   dynamically assigned ports, which are communicated to its peers
   during discovery.  However, a minimal implementation MAY use the
   GRASP Listen Port for this purpose.

3.3.4.  Discovery Mechanism and Procedures

   o  Separated discovery and negotiation mechanisms

         Although discovery and negotiation or synchronization are
         defined together in the GRASP, they are separated mechanisms.
         The discovery process could run independently from the
         negotiation or synchronization process.  Upon receiving a
         Discovery (Section 3.7.3) message, the recipient node should
         return a response message in which it either indicates itself
         as a discovery responder or diverts the initiator towards
         another more suitable ASA.

         The discovery action will normally be followed by a negotiation
         or synchronization action.  The discovery results could be
         utilized by the negotiation protocol to decide which ASA the
         initiator will negotiate with.

         The initiator of a discovery action for a given objective need
         not be capable of responding to that objective as a Negotiation
         Counterpart, as a Synchronization Responder or as source for
         flooding.  For example, an ASA might perform discovery even if
         it only wishes to act a Synchronization Initiator or
         Negotiation Initiator.  Such an ASA does not itself need to
         respond to discovery messages.

         It is also entirely possible to use GRASP discovery without any
         subsequent negotiation or synchronization action.  In this
         case, the discovered objective is simply used as a name during
         the discovery process and any subsequent operations between the
         peers are outside the scope of GRASP.

   o  Discovery Procedures

         Discovery starts as an on-link operation.  The Divert option
         can tell the discovery initiator to contact an off-link ASA for
         that discovery objective.  Every Discovery message is sent by a
         discovery initiator via UDP to the ALL_GRASP_NEIGHBOR link-
         local multicast address (Section 3.5).  Every network device
         that supports GRASP always listens to a well-known UDP port to
         capture the discovery messages.  Because this port is unique in
         a device, this is a function of the GRASP kernel and not of an

Bormann, et al.          Expires March 17, 2017                [Page 18]
Internet-Draft                    GRASP                   September 2016

         individual ASA.  As a result, each ASA will need to register
         the objectives that it supports with the GRASP kernel.

         If an ASA in a neighbor device supports the requested discovery
         objective, the device SHOULD respond to the link-local
         multicast with a unicast Discovery Response message
         (Section 3.7.4) with locator option(s), unless it is
         temporarily unavailable.  Otherwise, if the neighbor has cached
         information about an ASA that supports the requested discovery
         objective (usually because it discovered the same objective
         before), it SHOULD respond with a Discovery Response message
         with a Divert option pointing to the appropriate Discovery
         Responder.

         If a device has no information about the requested discovery
         objective, and is not acting as a discovery relay (see below)
         it MUST silently discard the Discovery message.

         If no discovery response is received within a reasonable
         timeout (default GRASP_DEF_TIMEOUT milliseconds, Section 3.5),
         the Discovery message MAY be repeated, with a newly generated
         Session ID (Section 3.6).  An exponential backoff SHOULD be
         used for subsequent repetitions, in order to mitigate possible
         denial of service attacks.

         After a GRASP device successfully discovers a locator for a
         Discovery Responder supporting a specific objective, it MUST
         cache this information, including the interface identifier via
         which it was discovered.  This cache record MAY be used for
         future negotiation or synchronization, and the locator SHOULD
         be passed on when appropriate as a Divert option to another
         Discovery Initiator.

         The cache mechanism MUST include a lifetime for each entry.
         The lifetime is derived from a time-to-live (ttl) parameter in
         each Discovery Response message.  Cached entries MUST be
         ignored or deleted after their lifetime expires.  In some
         environments, unplanned address renumbering might occur.  In
         such cases, the lifetime SHOULD be short compared to the
         typical address lifetime and a mechanism to flush the discovery
         cache SHOULD be implemented.  The discovery mechanism needs to
         track the node's current address to ensure that Discovery
         Responses always indicate the correct address.

         If multiple Discovery Responders are found for the same
         objective, they SHOULD all be cached, unless this creates a
         resource shortage.  The method of choosing between multiple
         responders is an implementation choice.  This choice MUST be

Bormann, et al.          Expires March 17, 2017                [Page 19]
Internet-Draft                    GRASP                   September 2016

         available to each ASA but the GRASP implementation SHOULD
         provide a default choice.

         Because Discovery Responders will be cached in a finite cache,
         they might be deleted at any time.  In this case, discovery
         will need to be repeated.  If an ASA exits for any reason, its
         locator might still be cached for some time, and attempts to
         connect to it will fail.  ASAs need to be robust in these
         circumstances.

         A GRASP device with multiple link-layer interfaces (typically a
         router) MUST support discovery on all interfaces.  If it
         receives a Discovery message on a given interface for a
         specific objective that it does not support and for which it
         has not previously cached a Discovery Responder, it MUST relay
         the query by re-issuing a Discovery message as a link-local
         multicast on its other interfaces.  The relayed discovery
         message MUST have the same Session ID as the incoming discovery
         message and MUST be tagged with the IP address of its original
         initiator.  Since the relay device is unaware of the timeout
         set by the original initiator it SHOULD set a timeout at least
         equal to GRASP_DEF_TIMEOUT milliseconds.

         The relaying device MUST decrement the loop count within the
         objective, and MUST NOT relay the Discovery message if the
         result is zero.  Also, it MUST limit the total rate at which it
         relays discovery messages to a reasonable value, in order to
         mitigate possible denial of service attacks.  It MUST cache the
         Session ID value and initiator address of each relayed
         Discovery message until any Discovery Responses have arrived or
         the discovery process has timed out.  To prevent loops, it MUST
         NOT relay a Discovery message which carries a given cached
         Session ID and initiator address more than once.  These
         precautions avoid discovery loops and mitigate potential
         overload.

         The discovery results received by the relaying device MUST in
         turn be sent as a Discovery Response message to the Discovery
         message that caused the relay action.

         This relayed discovery mechanism, with caching of the results,
         should be sufficient to support most network bootstrapping
         scenarios.

   o  A complete discovery process will start with a multicast on the
      local link.  On-link neighbors supporting the discovery objective
      will respond directly.  A neighbor with multiple interfaces will
      respond with a cached discovery response if any.  If not, it will

Bormann, et al.          Expires March 17, 2017                [Page 20]
Internet-Draft                    GRASP                   September 2016

      relay the discovery on its other interfaces, for example reaching
      a higher-level gateway in a hierarchical network.  If a node
      receiving the relayed discovery supports the discovery objective,
      it will respond to the relayed discovery.  If it has a cached
      response, it will respond with that.  If not, it will repeat the
      discovery process, which thereby becomes recursive.  The loop
      count and timeout will ensure that the process ends.

   o  Rapid Mode (Discovery/Negotiation binding)

         A Discovery message MAY include a Negotiation Objective option.
         This allows a rapid mode of negotiation described in
         Section 3.3.5.  A similar mechanism is defined for
         synchronization in Section 3.3.6.

         Note that rapid mode is currently limited to a single objective
         for simplicity of design and implementation.  A possible future
         extension is to allow multiple objectives in rapid mode for
         greater efficiency.

3.3.5.  Negotiation Procedures

   A negotiation initiator sends a negotiation request to a counterpart
   ASA, including a specific negotiation objective.  It may request the
   negotiation counterpart to make a specific configuration.
   Alternatively, it may request a certain simulation or forecast result
   by sending a dry run configuration.  The details, including the
   distinction between dry run and an actual configuration change, will
   be defined separately for each type of negotiation objective.

   If no reply message of any kind is received within a reasonable
   timeout (default GRASP_DEF_TIMEOUT milliseconds, Section 3.5), the
   negotiation request MAY be repeated, with a newly generated Session
   ID (Section 3.6).  An exponential backoff SHOULD be used for
   subsequent repetitions.

   If the counterpart can immediately apply the requested configuration,
   it will give an immediate positive (accept) answer.  This will end
   the negotiation phase immediately.  Otherwise, it will negotiate.  It
   will reply with a proposed alternative configuration that it can
   apply (typically, a configuration that uses fewer resources than
   requested by the negotiation initiator).  This will start a bi-
   directional negotiation to reach a compromise between the two ASAs.

   The negotiation procedure is ended when one of the negotiation peers
   sends a Negotiation Ending message, which contains an accept or
   decline option and does not need a response from the negotiation

Bormann, et al.          Expires March 17, 2017                [Page 21]
Internet-Draft                    GRASP                   September 2016

   peer.  Negotiation may also end in failure (equivalent to a decline)
   if a timeout is exceeded or a loop count is exceeded.

   A negotiation procedure concerns one objective and one counterpart.
   Both the initiator and the counterpart may take part in simultaneous
   negotiations with various other ASAs, or in simultaneous negotiations
   about different objectives.  Thus, GRASP is expected to be used in a
   multi-threaded mode.  Certain negotiation objectives may have
   restrictions on multi-threading, for example to avoid over-allocating
   resources.

   Some configuration actions, for example wavelength switching in
   optical networks, might take considerable time to execute.  The ASA
   concerned needs to allow for this by design, but GRASP does allow for
   a peer to insert latency in a negotiation process if necessary
   (Section 3.7.8).

3.3.5.1.  Rapid Mode (Discovery/Negotiation Linkage)

   A Discovery message MAY include a Negotiation Objective option.  In
   this case the Discovery message also acts as a Request Negotiation
   message to indicate to the Discovery Responder that it could directly
   reply to the Discovery Initiator with a Negotiation message for rapid
   processing, if it could act as the corresponding negotiation
   counterpart.  However, the indication is only advisory not
   prescriptive.

   It is possible that a Discovery Response will arrive from a responder
   that does not support rapid mode, before such a Negotiation message
   arrives.  In this case, rapid mode will not occur.

   This rapid mode could reduce the interactions between nodes so that a
   higher efficiency could be achieved.  However, a network in which
   some nodes support rapid mode and others do not will have complex
   timing-dependent behaviors.  Therefore, the rapid negotiation
   function SHOULD be configured off by default and MAY be configured on
   or off by Intent.

3.3.6.  Synchronization and Flooding Procedure

   A synchronization initiator sends a synchronization request to a
   counterpart, including a specific synchronization objective.  The
   counterpart responds with a Synchronization message (Section 3.7.9)
   containing the current value of the requested synchronization
   objective.  No further messages are needed.

   If no reply message of any kind is received within a reasonable
   timeout (default GRASP_DEF_TIMEOUT milliseconds, Section 3.5), the

Bormann, et al.          Expires March 17, 2017                [Page 22]
Internet-Draft                    GRASP                   September 2016

   synchronization request MAY be repeated, with a newly generated
   Session ID (Section 3.6).  An exponential backoff SHOULD be used for
   subsequent repetitions.

3.3.6.1.  Flooding

   In the case just described, the message exchange is unicast and
   concerns only one synchronization objective.  For large groups of
   nodes requiring the same data, synchronization flooding is available.
   For this, a flooding initiator MAY send an unsolicited Flood
   Synchronization message containing one or more Synchronization
   Objective option(s), if and only if the specification of those
   objectives permits it.  This is sent as a multicast message to the
   ALL_GRASP_NEIGHBOR multicast address (Section 3.5).

   Every network device that supports GRASP always listens to a well-
   known UDP port to capture flooding messages.  Because this port is
   unique in a device, this is a function of the GRASP kernel.

   To ensure that flooding does not result in a loop, the originator of
   the Flood Synchronization message MUST set the loop count in the
   objectives to a suitable value (the default is GRASP_DEF_LOOPCT).
   Also, a suitable mechanism is needed to avoid excessive multicast
   traffic.  This mechanism MUST be defined as part of the specification
   of the synchronization objective(s) concerned.  It might be a simple
   rate limit or a more complex mechanism such as the Trickle algorithm
   [RFC6206].

   A GRASP device with multiple link-layer interfaces (typically a
   router) MUST support synchronization flooding on all interfaces.  If
   it receives a multicast Flood Synchronization message on a given
   interface, it MUST relay it by re-issuing a Flood Synchronization
   message on its other interfaces.  The relayed message MUST have the
   same Session ID as the incoming message and MUST be tagged with the
   IP address of its original initiator.

   The relaying device MUST decrement the loop count within the first
   objective, and MUST NOT relay the Flood Synchronization message if
   the result is zero.  Also, it MUST limit the total rate at which it
   relays Flood Synchronization messages to a reasonable value, in order
   to mitigate possible denial of service attacks.  It MUST cache the
   Session ID value and initiator address of each relayed Flood
   Synchronization message for a finite time not less than twice
   GRASP_DEF_TIMEOUT milliseconds.  To prevent loops, it MUST NOT relay
   a Flood Synchronization message which carries a given cached Session
   ID and initiator address more than once.  These precautions avoid
   synchronization loops and mitigate potential overload.

Bormann, et al.          Expires March 17, 2017                [Page 23]
Internet-Draft                    GRASP                   September 2016

   Note that this mechanism is unreliable in the case of sleeping nodes,
   or new nodes that join the network, or nodes that rejoin the network
   after a fault.  An ASA that initiates a flood SHOULD repeat the flood
   at a suitable frequency and SHOULD also act as a synchronization
   responder for the objective(s) concerned.  Thus nodes that require an
   objective subject to flooding can either wait for the next flood or
   request unicast synchronization for that objective.

   The multicast messages for synchronization flooding are subject to
   the security rules in Section 3.3.1.  In practice this means that
   they MUST NOT be transmitted and MUST be ignored on receipt unless
   there is an operational ACP or equivalent strong security in place.
   However, because of the security weakness of link-local multicast
   (Section 5), synchronization objectives that are flooded SHOULD NOT
   contain unencrypted private information and SHOULD be validated by
   the recipient ASA.

3.3.6.2.  Rapid Mode (Discovery/Synchronization Linkage)

   A Discovery message MAY include a Synchronization Objective option.
   In this case the Discovery message also acts as a Request
   Synchronization message to indicate to the Discovery Responder that
   it could directly reply to the Discovery Initiator with a
   Synchronization message Section 3.7.9 with synchronization data for
   rapid processing, if the discovery target supports the corresponding
   synchronization objective.  However, the indication is only advisory
   not prescriptive.

   It is possible that a Discovery Response will arrive from a responder
   that does not support rapid mode, before such a Synchronization
   message arrives.  In this case, rapid mode will not occur.

   This rapid mode could reduce the interactions between nodes so that a
   higher efficiency could be achieved.  However, a network in which
   some nodes support rapid mode and others do not will have complex
   timing-dependent behaviors.  Therefore, the rapid synchronization
   function SHOULD be configured off by default and MAY be configured on
   or off by Intent.

3.4.  High Level Deployment Model

   It is expected that a GRASP implementation will reside in an
   autonomic node that also contains both the appropriate security
   environment (preferably the ACP) and one or more Autonomic Service
   Agents (ASAs).  In the minimal case of a single-purpose device, these
   three components might be fully integrated.  A more common model is
   expected to be a multi-purpose device capable of containing several
   ASAs.  In this case it is expected that the ACP, GRASP and the ASAs

Bormann, et al.          Expires March 17, 2017                [Page 24]
Internet-Draft                    GRASP                   September 2016

   will be implemented as separate processes, which are probably multi-
   threaded to support asynchronous and simultaneous operations.  It is
   expected that GRASP will access the ACP by using a typical socket
   interface.  A well defined Application Programming Interface (API)
   will be needed between GRASP and the ASAs.  In some implementations,
   ASAs would run in user space with a GRASP library providing the API,
   and this library would in turn communicate via system calls with core
   GRASP functions running in kernel mode.  For further details of
   possible deployment models, see [I-D.ietf-anima-reference-model].

   Because GRASP needs to work whatever happens, especially during
   bootstrapping and during fault conditions, it is essential that every
   implementation is as robust as possible.  For example, discovery
   failures, or any kind of socket error at any time, must not cause
   irrecoverable failures in GRASP itself, and must return suitable
   error codes through the API so that ASAs can also recover.

   GRASP must always start up correctly after a system restart.  All run
   time error conditions, and events such as address renumbering,
   network interface failures, and CPU sleep/wake cycles, must be
   handled in such a way that GRASP will still operate correctly and
   securely (Section 3.3.1) afterwards.

   An autonomic node will normally run a single instance of GRASP, used
   by multiple ASAs.  However, scenarios where multiple instances of
   GRASP run in a single node, perhaps with different security
   properties, are not excluded.  In this case, each instance MUST
   listen independently for GRASP link-local muticasts in order for
   discovery and flooding to work correctly.

3.5.  GRASP Constants

   o  ALL_GRASP_NEIGHBOR

      A link-local scope multicast address used by a GRASP-enabled
      device to discover GRASP-enabled neighbor (i.e., on-link) devices
      . All devices that support GRASP are members of this multicast
      group.

      *  IPv6 multicast address: TBD1

      *  IPv4 multicast address: TBD2

   o  GRASP_LISTEN_PORT (TBD3)

      A well-known UDP user port that every GRASP-enabled network device
      MUST always listen to for link-local multicasts.  Additionally,

Bormann, et al.          Expires March 17, 2017                [Page 25]
Internet-Draft                    GRASP                   September 2016

      this user port MAY be used to listen for TCP or UDP unicast
      messages in a simple implementation of GRASP (Section 3.3.3).

   o  GRASP_DEF_TIMEOUT (60000 milliseconds)

      The default timeout used to determine that a discovery etc. has
      failed to complete.

   o  GRASP_DEF_LOOPCT (6)

      The default loop count used to determine that a negotiation has
      failed to complete, and to avoid looping messages.

3.6.  Session Identifier (Session ID)

   This is an up to 24-bit opaque value used to distinguish multiple
   sessions between the same two devices.  A new Session ID MUST be
   generated by the initiator for every new Discovery, Flood
   Synchronization or Request message.  All responses and follow-up
   messages in the same discovery, synchronization or negotiation
   procedure MUST carry the same Session ID.

   The Session ID SHOULD have a very low collision rate locally.  It
   MUST be generated by a pseudo-random algorithm using a locally
   generated seed which is unlikely to be used by any other device in
   the same network [RFC4086].

   However, there is a finite probability that two nodes might generate
   the same Session ID value.  For that reason, when a Session ID is
   communicated via GRASP, the receiving node MUST tag it with the
   initiator's IP address to allow disambiguation.  Multicast GRASP
   messages and their responses, which may be relayed between links,
   therefore include a field that carries the initiator's global IP
   address.

3.7.  GRASP Messages

3.7.1.  Message Overview

   This section defines the GRASP message format and message types.
   Message types not listed here are reserved for future use.

   The messages currently defined are:

      Discovery and Discovery Response.

      Request Negotiation, Negotiation, Confirm Waiting and Negotiation
      End.

Bormann, et al.          Expires March 17, 2017                [Page 26]
Internet-Draft                    GRASP                   September 2016

      Request Synchronization, Synchronization, and Flood
      Synchronization.

      No Operation.

3.7.2.  GRASP Message Format

   GRASP messages share an identical header format and a variable format
   area for options.  GRASP message headers and options are transmitted
   in Concise Binary Object Representation (CBOR) [RFC7049].  In this
   specification, they are described using CBOR data definition language
   (CDDL) [I-D.greevenbosch-appsawg-cbor-cddl].  Fragmentary CDDL is
   used to describe each item in this section.  A complete and normative
   CDDL specification of GRASP is given in Section 6, including
   constants such as message types.

   Every GRASP message, except the No Operation message, carries a
   Session ID (Section 3.6).  Options are then presented serially in the
   options field.

   In fragmentary CDDL, every GRASP message follows the pattern:

     grasp-message = (message .within message-structure) / noop-message

     message-structure = [MESSAGE_TYPE, session-id, ?initiator,
                          *grasp-option]

     MESSAGE_TYPE = 1..255
     session-id = 0..16777215 ;up to 24 bits
     grasp-option = any

   The MESSAGE_TYPE indicates the type of the message and thus defines
   the expected options.  Any options received that are not consistent
   with the MESSAGE_TYPE SHOULD be silently discarded.

   The No Operation (noop) message is described in Section 3.7.11.

   The various MESSAGE_TYPE values are defined in Section 6.

   All other message elements are described below and formally defined
   in Section 6.

3.7.3.  Discovery Message

   In fragmentary CDDL, a Discovery message follows the pattern:

     discovery-message = [M_DISCOVERY, session-id, initiator, objective]

Bormann, et al.          Expires March 17, 2017                [Page 27]
Internet-Draft                    GRASP                   September 2016

   A discovery initiator sends a Discovery message to initiate a
   discovery process for a particular objective option.

   The discovery initiator sends the Discovery messages via UDP to port
   GRASP_LISTEN_PORT at the link-local ALL_GRASP_NEIGHBOR multicast
   address.  It then listens for unicast TCP responses on the same port,
   and stores the discovery results (including responding discovery
   objectives and corresponding unicast locators).

   The 'initiator' field in the message is a globally unique IP address
   of the initiator, for the sole purpose of disambiguating the Session
   ID in other nodes.  If for some reason the initiator does not have a
   globally unique IP address, it MUST use a link-local address for this
   purpose that is highly likely to be unique, for example using
   [RFC7217].

   A Discovery message MUST include exactly one of the following:

   o  a discovery objective option (Section 3.9.1).  Its loop count MUST
      be set to a suitable value to prevent discovery loops (default
      value is GRASP_DEF_LOOPCT).  If the discovery initiator requires
      only on-link responses, the loop count MUST be set to 1.

   o  a negotiation objective option (Section 3.9.1).  This is used both
      for the purpose of discovery and to indicate to the discovery
      target that it MAY directly reply to the discovery initiatior with
      a Negotiation message for rapid processing, if it could act as the
      corresponding negotiation counterpart.  The sender of such a
      Discovery message MUST initialize a negotiation timer and loop
      count in the same way as a Request Negotiation message
      (Section 3.7.5).

   o  a synchronization objective option (Section 3.9.1).  This is used
      both for the purpose of discovery and to indicate to the discovery
      target that it MAY directly reply to the discovery initiator with
      a Synchronization message for rapid processing, if it could act as
      the corresponding synchronization counterpart.  Its loop count
      MUST be set to a suitable value to prevent discovery loops
      (default value is GRASP_DEF_LOOPCT).

3.7.4.  Discovery Response Message

   In fragmentary CDDL, a Discovery Response message follows the
   pattern:

Bormann, et al.          Expires March 17, 2017                [Page 28]
Internet-Draft                    GRASP                   September 2016

     response-message = [M_RESPONSE, session-id, initiator, ttl,
                        (+locator-option // divert-option), ?objective)]

     ttl = 0..4294967295 ; in milliseconds

   A node which receives a Discovery message SHOULD send a Discovery
   Response message if and only if it can respond to the discovery.

      It MUST contain the same Session ID and initiator as the Discovery
      message.

      It MUST contain a time-to-live (ttl) for the validity of the
      response, given as a positive integer value in milliseconds.  Zero
      is treated as the default value GRASP_DEF_TIMEOUT (Section 3.5).

      It MAY include a copy of the discovery objective from the
      Discovery message.

   It is sent to the sender of the Discovery message via TCP at the port
   used to send the Discovery message.

   If the responding node supports the discovery objective of the
   discovery, it MUST include at least one kind of locator option
   (Section 3.8.5) to indicate its own location.  A sequence of multiple
   kinds of locator options (e.g.  IP address option and FQDN option) is
   also valid.

   If the responding node itself does not support the discovery
   objective, but it knows the locator of the discovery objective, then
   it SHOULD respond to the discovery message with a divert option
   (Section 3.8.2) embedding a locator option or a combination of
   multiple kinds of locator options which indicate the locator(s) of
   the discovery objective.

   More details on the processing of Discovery Responses are given in
   Section 3.3.4.

3.7.5.  Request Messages

   In fragmentary CDDL, Request Negotiation and Request Synchronization
   messages follow the patterns:

   request-negotiation-message = [M_REQ_NEG, session-id, objective]

   request-synchronization-message = [M_REQ_SYN, session-id, objective]

Bormann, et al.          Expires March 17, 2017                [Page 29]
Internet-Draft                    GRASP                   September 2016

   A negotiation or synchronization requesting node sends the
   appropriate Request message to the unicast address (directly stored
   or resolved from an FQDN or URI) of the negotiation or
   synchronization counterpart, using the appropriate protocol and port
   numbers (selected from the discovery results).

   A Request message MUST include the relevant objective option.  In the
   case of Request Negotiation, the objective option MUST include the
   requested value.

   When an initiator sends a Request Negotiation message, it MUST
   initialize a negotiation timer for the new negotiation thread with
   the value GRASP_DEF_TIMEOUT milliseconds.  Unless this timeout is
   modified by a Confirm Waiting message (Section 3.7.8), the initiator
   will consider that the negotiation has failed when the timer expires.

   When an initiator sends a Request message, it MUST initialize the
   loop count of the objective option with a value defined in the
   specification of the option or, if no such value is specified, with
   GRASP_DEF_LOOPCT.

   If a node receives a Request message for an objective for which no
   ASA is currently listening, it MUST immediately close the relevant
   socket to indicate this to the initiator.

3.7.6.  Negotiation Message

   In fragmentary CDDL, a Negotiation message follows the pattern:

     discovery-message = [M_NEGOTIATE, session-id, objective]

   A negotiation counterpart sends a Negotiation message in response to
   a Request Negotiation message, a Negotiation message, or a Discovery
   message in Rapid Mode.  A negotiation process MAY include multiple
   steps.

   The Negotiation message MUST include the relevant Negotiation
   Objective option, with its value updated according to progress in the
   negotiation.  The sender MUST decrement the loop count by 1.  If the
   loop count becomes zero the message MUST NOT be sent.  In this case
   the negotiation session has failed and will time out.

3.7.7.  Negotiation End Message

   In fragmentary CDDL, a Negotiation End message follows the pattern:

     end-message = [M_END, session-id, accept-option / decline-option]

Bormann, et al.          Expires March 17, 2017                [Page 30]
Internet-Draft                    GRASP                   September 2016

   A negotiation counterpart sends an Negotiation End message to close
   the negotiation.  It MUST contain either an accept or a decline
   option, defined in Section 3.8.3 and Section 3.8.4.  It could be sent
   either by the requesting node or the responding node.

3.7.8.  Confirm Waiting Message

   In fragmentary CDDL, a Confirm Waiting message follows the pattern:

     wait-message = [M_WAIT, session-id, waiting-time]
     waiting-time =        0..4294967295 ; in milliseconds

   A responding node sends a Confirm Waiting message to ask the
   requesting node to wait for a further negotiation response.  It might
   be that the local process needs more time or that the negotiation
   depends on another triggered negotiation.  This message MUST NOT
   include any other options.  When received, the waiting time value
   overwrites and restarts the current negotiation timer
   (Section 3.7.5).

   The responding node SHOULD send a Negotiation, Negotiation End or
   another Confirm Waiting message before the negotiation timer expires.
   If not, the initiator MUST abandon or restart the negotiation
   procedure, to avoid an indefinite wait.

3.7.9.  Synchronization Message

   In fragmentary CDDL, a Synchronization message follows the pattern:

     synch-message = [M_SYNCH, session-id, objective]

   A node which receives a Request Synchronization, or a Discovery
   message in Rapid Mode, sends back a unicast Synchronization message
   with the synchronization data, in the form of a GRASP Option for the
   specific synchronization objective present in the Request
   Synchronization.

3.7.10.  Flood Synchronization Message

   In fragmentary CDDL, a Flood Synchronization message follows the
   pattern:

     flood-message = [M_FLOOD, session-id, initiator, ttl,
                     (locator-option / []), +objective]

     ttl = 0..4294967295 ; in milliseconds

Bormann, et al.          Expires March 17, 2017                [Page 31]
Internet-Draft                    GRASP                   September 2016

   A node MAY initiate flooding by sending an unsolicited Flood
   Synchronization Message with synchronization data.  This MAY be sent
   to the link-local ALL_GRASP_NEIGHBOR multicast address, in accordance
   with the rules in Section 3.3.6.

      The initiator address is provided as described for Discovery
      messages.

      The message MUST contain a time-to-live (ttl) for the validity of
      the response, given as a positive integer value in milliseconds.
      There is no default; zero indicates an indefinite lifetime.

      The message MAY contain a locator option indicating the ASA that
      initiated the flooded data.  In its absence, an empty option MUST
      be included.

      The synchronization data are in the form of GRASP Option(s) for
      specific synchronization objective(s).  The loop count(s) MUST be
      set to a suitable value to prevent flood loops (default value is
      GRASP_DEF_LOOPCT).

   A node that receives a Flood Synchronization message MUST cache the
   received objectives for use by local ASAs.  Each cached objective
   MUST be tagged with the locator option sent with it, or with a null
   tag if an empty locator option was sent.  If a subsequent Flood
   Synchronization message carrying the same objective arrives with the
   same tag, the corresponding cached copy of the objective MUST be
   overwritten.  If a subsequent Flood Synchronization message carrying
   the same objective arrives with a different tag, a new cached entry
   MUST be created.

   Note: the purpose of this mechanism is to allow the recipient of
   flooded values to distinguish between different senders of the same
   objective, and if necessary communicate with them using the locator,
   protocol and port included in the locator option.  Many objectives
   will not need this mechanism, so they will be flooded with a null
   locator.

   Cached entries MUST be ignored or deleted after their lifetime
   expires.

3.7.11.  No Operation Message

   In fragmentary CDDL, a No Operation message follows the pattern:

     noop-message = [M_NOOP]

Bormann, et al.          Expires March 17, 2017                [Page 32]
Internet-Draft                    GRASP                   September 2016

   This message MAY be sent by an implementation that for practical
   reasons needs to activate a socket.  It MUST be silently ignored by a
   recipient.

3.8.  GRASP Options

   This section defines the GRASP options for the negotiation and
   synchronization protocol signaling.  Additional options may be
   defined in the future.

3.8.1.  Format of GRASP Options

   GRASP options are CBOR objects that MUST start with an unsigned
   integer identifying the specific option type carried in this option.
   These option types are formally defined in Section 6.  Apart from
   that the only format requirement is that each option MUST be a well-
   formed CBOR object.  In general a CBOR array format is RECOMMENDED to
   limit overhead.

   GRASP options are usually scoped by using encapsulation.  However,
   this is not a requirement

3.8.2.  Divert Option

   The Divert option is used to redirect a GRASP request to another
   node, which may be more appropriate for the intended negotiation or
   synchronization.  It may redirect to an entity that is known as a
   specific negotiation or synchronization counterpart (on-link or off-
   link) or a default gateway.  The divert option MUST only be
   encapsulated in Discovery Response messages.  If found elsewhere, it
   SHOULD be silently ignored.

   A discovery initiator MAY ignore a Divert option if it only requires
   direct discovery responses.

   In fragmentary CDDL, the Divert option follows the pattern:

     divert-option = [O_DIVERT, +locator-option]

   The embedded Locator Option(s) (Section 3.8.5) point to diverted
   destination target(s) in response to a Discovery message.

3.8.3.  Accept Option

   The accept option is used to indicate to the negotiation counterpart
   that the proposed negotiation content is accepted.

Bormann, et al.          Expires March 17, 2017                [Page 33]
Internet-Draft                    GRASP                   September 2016

   The accept option MUST only be encapsulated in Negotiation End
   messages.  If found elsewhere, it SHOULD be silently ignored.

   In fragmentary CDDL, the Accept option follows the pattern:

     accept-option = [O_ACCEPT]

3.8.4.  Decline Option

   The decline option is used to indicate to the negotiation counterpart
   the proposed negotiation content is declined and end the negotiation
   process.

   The decline option MUST only be encapsulated in Negotiation End
   messages.  If found elsewhere, it SHOULD be silently ignored.

   In fragmentary CDDL, the Decline option follows the pattern:

     decline-option = [O_DECLINE, ?reason]
     reason = text  ;optional error message

   Note: there are scenarios where a negotiation counterpart wants to
   decline the proposed negotiation content and continue the negotiation
   process.  For these scenarios, the negotiation counterpart SHOULD use
   a Negotiate message, with either an objective option that contains a
   data field set to indicate a meaningless initial value, or a specific
   objective option that provides further conditions for convergence.

3.8.5.  Locator Options

   These locator options are used to present reachability information
   for an ASA, a device or an interface.  They are Locator IPv6 Address
   Option, Locator IPv4 Address Option, Locator FQDN (Fully Qualified
   Domain Name) Option and URI (Uniform Resource Identifier) Option.

   Since ASAs will normally run as independent user programs, locator
   options need to indicate the network layer locator plus the transport
   protocol and port number for reaching the target.  For this reason,
   the Locator Options for IP addresses and FQDNs include this
   information explicitly.  In the case of the URI Option, this
   information can be encoded in the URI itself.

   Note: It is assumed that all locators are in scope throughout the
   GRASP domain.  GRASP is not intended to work across disjoint
   addressing or naming realms.

Bormann, et al.          Expires March 17, 2017                [Page 34]
Internet-Draft                    GRASP                   September 2016

3.8.5.1.  Locator IPv6 address option

   In fragmentary CDDL, the IPv6 address option follows the pattern:

     ipv6-locator-option = [O_IPv6_LOCATOR, ipv6-address,
                            transport-proto, port-number]
     ipv6-address = bytes .size 16

     transport-proto = IPPROTO_TCP / IPPROTO_UDP
     IPPROTO_TCP = 6
     IPPROTO_UDP = 17
     port-number = 0..65535

   The content of this option is a binary IPv6 address followed by the
   protocol number and port number to be used.

   Note 1: The IPv6 address MUST normally have global scope.
   Exceptionally, during node bootstrap, a link-local address MAY be
   used for specific objectives only.

   Note 2: A link-local IPv6 address MUST NOT be used when this option
   is included in a Divert option.

3.8.5.2.  Locator IPv4 address option

   In fragmentary CDDL, the IPv4 address option follows the pattern:

     ipv4-locator-option = [O_IPv4_LOCATOR, ipv4-address,
                            transport-proto, port-number]
     ipv4-address = bytes .size 4

   The content of this option is a binary IPv4 address followed by the
   protocol number and port number to be used.

   Note: If an operator has internal network address translation for
   IPv4, this option MUST NOT be used within the Divert option.

3.8.5.3.  Locator FQDN option

   In fragmentary CDDL, the FQDN option follows the pattern:

     fqdn-locator-option = [O_FQDN_LOCATOR, text,
                            transport-proto, port-number]

   The content of this option is the Fully Qualified Domain Name of the
   target followed by the protocol number and port number to be used.

Bormann, et al.          Expires March 17, 2017                [Page 35]
Internet-Draft                    GRASP                   September 2016

   Note 1: Any FQDN which might not be valid throughout the network in
   question, such as a Multicast DNS name [RFC6762], MUST NOT be used
   when this option is used within the Divert option.

   Note 2: Normal GRASP operations are not expected to use this option.
   It is intended for special purposes such as discovering external
   services.

3.8.5.4.  Locator URI option

   In fragmentary CDDL, the URI option follows the pattern:

     uri-locator = [O_URI_LOCATOR, text]

   The content of this option is the Uniform Resource Identifier of the
   target [RFC3986].

   Note 1: Any URI which might not be valid throughout the network in
   question, such as one based on a Multicast DNS name [RFC6762], MUST
   NOT be used when this option is used within the Divert option.

   Note 2: Normal GRASP operations are not expected to use this option.
   It is intended for special purposes such as discovering external
   services.

3.9.  Objective Options

3.9.1.  Format of Objective Options

   An objective option is used to identify objectives for the purposes
   of discovery, negotiation or synchronization.  All objectives MUST be
   in the following format, described in fragmentary CDDL:

     objective = [objective-name, objective-flags, loop-count, ?any]

     objective-name = text
     loop-count = 0..255

   All objectives are identified by a unique name which is a case-
   sensitive UTF-8 string.

   The names of generic objectives MUST NOT include a colon (":") and
   MUST be registered with IANA (Section 7).

   The names of privately defined objectives MUST include at least one
   colon (":").  The string preceding the last colon in the name MUST be
   globally unique and in some way identify the entity or person

Bormann, et al.          Expires March 17, 2017                [Page 36]
Internet-Draft                    GRASP                   September 2016

   defining the objective.  The following three methods MAY be used to
   create such a globally unique string:

   1.  The unique string is a decimal number representing a registered
       32 bit Private Enterprise Number (PEN) [I-D.liang-iana-pen] that
       uniquely identifies the enterprise defining the objective.

   2.  The unique string is a fully qualified domain name that uniquely
       identifies the entity or person defining the objective.

   3.  The unique string is an email address that uniquely identifies
       the entity or person defining the objective.

   The GRASP protocol treats the objective name as an opaque string.
   For example, "EX1", "411:EX1", "example.com:EX1", "example.org:EX1
   and "user@example.org:EX1" would be five different objectives.

   The 'objective-flags' field is described below.

   The 'loop-count' field is used for terminating negotiation as
   described in Section 3.7.6.  It is also used for terminating
   discovery as described in Section 3.3.4, and for terminating flooding
   as described in Section 3.3.6.1.

   The 'any' field is to express the actual value of a negotiation or
   synchronization objective.  Its format is defined in the
   specification of the objective and may be a single value or a data
   structure of any kind.  It is optional because it is optional in a
   Discovery or Discovery Response message.

3.9.2.  Objective flags

   An objective may be relevant for discovery only, for discovery and
   negotiation, or for discovery and synchronization.  This is expressed
   in the objective by logical flags:

     objective-flags = uint .bits objective-flag
     objective-flag = &(
     F_DISC: 0   ; valid for discovery only
     F_NEG: 1    ; valid for discovery and negotiation
     F_SYNCH: 2  ; valid for discovery and synchronization
     )

3.9.3.  General Considerations for Objective Options

   As mentioned above, Objective Options MUST be assigned a unique name.
   As long as privately defined Objective Options obey the rules above,

Bormann, et al.          Expires March 17, 2017                [Page 37]
Internet-Draft                    GRASP                   September 2016

   this document does not restrict their choice of name, but the entity
   or person concerned SHOULD publish the names in use.

   All Objective Options MUST respect the CBOR patterns defined above as
   "objective" and MUST replace the "any" field with a valid CBOR data
   definition for the relevant use case and application.

   An Objective Option that contains no additional fields beyond its
   "loop-count" can only be a discovery objective and MUST only be used
   in Discovery and Discovery Response messages.

   The Negotiation Objective Options contain negotiation objectives,
   which vary according to different functions/services.  They MUST be
   carried by Discovery, Request Negotiation or Negotiation messages
   only.  The negotiation initiator MUST set the initial "loop-count" to
   a value specified in the specification of the objective or, if no
   such value is specified, to GRASP_DEF_LOOPCT.

   For most scenarios, there should be initial values in the negotiation
   requests.  Consequently, the Negotiation Objective options MUST
   always be completely presented in a Request Negotiation message, or
   in a Discovery message in rapid mode.  If there is no initial value,
   the bits in the value field SHOULD all be set to indicate a
   meaningless value, unless this is inappropriate for the specific
   negotiation objective.

   Synchronization Objective Options are similar, but MUST be carried by
   Discovery, Discovery Response, Request Synchronization, or Flood
   Synchronization messages only.  They include value fields only in
   Synchronization or Flood Synchronization messages.

3.9.4.  Organizing of Objective Options

   Generic objective options MUST be specified in documents available to
   the public and SHOULD be designed to use either the negotiation or
   the synchronization mechanism described above.

   As noted earlier, one negotiation objective is handled by each GRASP
   negotiation thread.  Therefore, a negotiation objective, which is
   based on a specific function or action, SHOULD be organized as a
   single GRASP option.  It is NOT RECOMMENDED to organize multiple
   negotiation objectives into a single option, nor to split a single
   function or action into multiple negotiation objectives.

   It is important to understand that GRASP negotiation does not support
   transactional integrity.  If transactional integrity is needed for a
   specific objective, this must be ensured by the ASA.  For example, an
   ASA might need to ensure that it only participates in one negotiation

Bormann, et al.          Expires March 17, 2017                [Page 38]
Internet-Draft                    GRASP                   September 2016

   thread at the same time.  Such an ASA would need to stop listening
   for incoming negotiation requests before generating an outgoing
   negotiation request.

   A synchronization objective SHOULD be organized as a single GRASP
   option.

   Some objectives will support more than one operational mode.  An
   example is a negotiation objective with both a "dry run" mode (where
   the negotiation is to find out whether the other end can in fact make
   the requested change without problems) and a "live" mode.  Such modes
   will be defined in the specification of such an objective.  These
   objectives SHOULD include flags indicating the applicable mode(s).

   An objective may have multiple parameters.  Parameters can be
   categorized into two classes: the obligatory ones presented as fixed
   fields; and the optional ones presented in CBOR sub-options or some
   other form of data structure embedded in CBOR.  The format might be
   inherited from an existing management or configuration protocol, the
   objective option acting as a carrier for that format.  The data
   structure might be defined in a formal language, but that is a matter
   for the specifications of individual objectives.  There are many
   candidates, according to the context, such as ABNF, RBNF, XML Schema,
   possibly YANG, etc.  The GRASP protocol itself is agnostic on these
   questions.

   It is NOT RECOMMENDED to split parameters in a single objective into
   multiple options, unless they have different response periods.  An
   exception scenario may also be described by split objectives.

   All objectives MUST support GRASP discovery.  However, as mentioned
   in Section 3.2, it is acceptable for an ASA to use an alternative
   method of discovery.

   Normally, a GRASP objective will refer to specific technical
   parameters as explained in Section 3.1.  However, it is acceptable to
   define an abstract objective for the purpose of managing or
   coordinating ASAs.  It is also acceptable to define a special-purpose
   objective for purposes such as trust bootstrapping or formation of
   the ACP.

3.9.5.  Experimental and Example Objective Options

   The names "EX0" through "EX9" have been reserved for experimental
   options.  Multiple names have been assigned because a single
   experiment may use multiple options simultaneously.  These
   experimental options are highly likely to have different meanings
   when used for different experiments.  Therefore, they SHOULD NOT be

Bormann, et al.          Expires March 17, 2017                [Page 39]
Internet-Draft                    GRASP                   September 2016

   used without an explicit human decision and SHOULD NOT be used in
   unmanaged networks such as home networks.

   These names are also RECOMMENDED for use in documentation examples.

4.  Implementation Status [RFC Editor: please remove]

   Two prototype implementations of GRASP have been made.

4.1.  BUPT C++ Implementation

   o  Name: BaseNegotiator.cpp, msg.cpp, Client.cpp, Server.cpp

   o  Description: C++ implementation of GRASP kernel and API

   o  Maturity: Prototype code, interoperable between Ubuntu.

   o  Coverage: Corresponds to draft-carpenter-anima-gdn-protocol-03.
      Since it was implemented based on the old version draft, the most
      significant limitations comparing to current protocol design
      include:

      *  Not support CBOR

      *  Not support Flooding

      *  Not support loop avoidance

      *  only coded for IPv6, any IPv4 is accidental

   o  Licensing: Huawei License.

   o  Experience: https://github.com/liubingpang/IETF-Anima-Signaling-
      Protocol/blob/master/README.md

   o  Contact: https://github.com/liubingpang/IETF-Anima-Signaling-
      Protocol

4.2.  Python Implementation

   o  Name: graspy

   o  Description: Python 3 implementation of GRASP kernel and API.

   o  Maturity: Prototype code, interoperable between Windows 7 and
      Debian.

Bormann, et al.          Expires March 17, 2017                [Page 40]
Internet-Draft                    GRASP                   September 2016

   o  Coverage: Corresponds to draft-ietf-anima-grasp-07.  Limitations
      include:

      *  insecure: uses a dummy ACP module and does not implement TLS

      *  only coded for IPv6, any IPv4 is accidental

      *  FQDN and URI locators incompletely supported

      *  no code for rapid mode

      *  relay code is lazy (no rate control)

      *  all unicast transactions use TCP (no unicast UDP).
         Experimental code for unicast UDP proved to be complex and
         brittle.

      *  optional Objective option in Response messages not implemented

      *  workarounds for defects in Python socket module and Windows
         socket peculiarities

   o  Licensing: Simplified BSD

   o  Experience: https://www.cs.auckland.ac.nz/~brian/graspy/graspy.pdf

   o  Contact: https://www.cs.auckland.ac.nz/~brian/graspy/

5.  Security Considerations

   It is obvious that a successful attack on negotiation-enabled nodes
   would be extremely harmful, as such nodes might end up with a
   completely undesirable configuration that would also adversely affect
   their peers.  GRASP nodes and messages therefore require full
   protection.

   - Authentication

      A cryptographically authenticated identity for each device is
      needed in an autonomic network.  It is not safe to assume that a
      large network is physically secured against interference or that
      all personnel are trustworthy.  Each autonomic node MUST be
      capable of proving its identity and authenticating its messages.
      GRASP relies on a separate external certificate-based security
      mechanism to support authentication, data integrity protection,
      and anti-replay protection.

Bormann, et al.          Expires March 17, 2017                [Page 41]
Internet-Draft                    GRASP                   September 2016

      Since GRASP is intended to be deployed in a single administrative
      domain operating its own trust anchor and CA, there is no need for
      a trusted public third party.  In a network requiring "air gap"
      security, such a dependency would be unacceptable.

      If GRASP is used temporarily without an external security
      mechanism, for example during system bootstrap (Section 3.3.1),
      the Session ID (Section 3.6) will act as a nonce to provide
      limited protection against third parties injecting responses.  A
      full analysis of the secure bootstrap process is out of scope for
      the present document.

   - Authorization and Roles

      The GRASP protocol is agnostic about the role of individual ASAs
      and about which objectives a particular ASA is authorized to
      support.  An implementation might support precautions such as
      allowing only one ASA in a given node to modify a given objective,
      but this may not be appropriate in all cases.  For example, it
      might be operationally useful to allow an old and a new version of
      the same ASA to run simultaneously during an overlap period.
      These questions are out of scope for the present specification.

   - Privacy and confidentiality

      Generally speaking, no personal information is expected to be
      involved in the signaling protocol, so there should be no direct
      impact on personal privacy.  Nevertheless, traffic flow paths,
      VPNs, etc. could be negotiated, which could be of interest for
      traffic analysis.  Also, operators generally want to conceal
      details of their network topology and traffic density from
      outsiders.  Therefore, since insider attacks cannot be excluded in
      a large network, the security mechanism for the protocol MUST
      provide message confidentiality.  This is why Section 3.3.1
      requires either an ACP or the use of TLS.

   - Link-local multicast security

      GRASP has no reasonable alternative to using link-local multicast
      for Discovery or Flood Synchronization messages and these messages
      are sent in clear and with no authentication.  They are therefore
      available to on-link eavesdroppers, and could be forged by on-link
      attackers.  In the case of Discovery, the Discovery Responses are
      unicast and will therefore be protected (Section 3.3.1), and an
      untrusted forger will not be able to receive responses.  In the
      case of Flood Synchronization, an on-link eavesdropper will be
      able to receive the flooded objectives but there is no response

Bormann, et al.          Expires March 17, 2017                [Page 42]
Internet-Draft                    GRASP                   September 2016

      message to consider.  Some precautions for Flood Synchronization
      messages are suggested in Section 3.3.6.1.

   - DoS Attack Protection

      GRASP discovery partly relies on insecure link-local multicast.
      Since routers participating in GRASP sometimes relay discovery
      messages from one link to another, this could be a vector for
      denial of service attacks.  Relevant mitigations are specified in
      Section 3.3.4.  Additionally, it is of great importance that
      firewalls prevent any GRASP messages from entering the domain from
      an untrusted source.

   - Security during bootstrap and discovery

      A node cannot authenticate GRASP traffic from other nodes until it
      has identified the trust anchor and can validate certificates for
      other nodes.  Also, until it has succesfully enrolled
      [I-D.ietf-anima-bootstrapping-keyinfra] it cannot assume that
      other nodes are able to authenticate its own traffic.  Therefore,
      GRASP discovery during the bootstrap phase for a new device will
      inevitably be insecure and GRASP synchronization and negotiation
      will be impossible until enrollment is complete.  Further details
      are given in Section 3.3.2.

   - Security of discovered locators

      When GRASP discovery returns an IP address, it MUST be that of a
      node within the secure environment (Section 3.3.1).  If it returns
      an FQDN or a URI, the ASA that receives it MUST NOT assume that
      the target of the locator is within the secure environment.

6.  CDDL Specification of GRASP

  <CODE BEGINS>
  grasp-message = (message .within message-structure) / noop-message

  message-structure = [MESSAGE_TYPE, session-id, ?initiator,
                       *grasp-option]

  MESSAGE_TYPE = 0..255
  session-id = 0..16777215 ;up to 24 bits
  grasp-option = any

  message /= discovery-message
  discovery-message = [M_DISCOVERY, session-id, initiator, objective]

  message /= response-message ;response to Discovery

Bormann, et al.          Expires March 17, 2017                [Page 43]
Internet-Draft                    GRASP                   September 2016

  response-message = [M_RESPONSE, session-id, initiator, ttl,
                     (+locator-option // divert-option), ?objective]

  message /= synch-message ;response to Synchronization request
  synch-message = [M_SYNCH, session-id, objective]

  message /= flood-message
  flood-message = [M_FLOOD, session-id, initiator, ttl,
                  (locator-option / []), +objective]

  message /= request-negotiation-message
  request-negotiation-message = [M_REQ_NEG, session-id, objective]

  message /= request-synchronization-message
  request-synchronization-message = [M_REQ_SYN, session-id, objective]

  message /= negotiation-message
  negotiation-message = [M_NEGOTIATE, session-id, objective]

  message /= end-message
  end-message = [M_END, session-id, accept-option / decline-option ]

  message /= wait-message
  wait-message = [M_WAIT, session-id, waiting-time]

  noop-message = [M_NOOP]

  divert-option = [O_DIVERT, +locator-option]

  accept-option = [O_ACCEPT]

  decline-option = [O_DECLINE, ?reason]
  reason = text  ;optional error message

  waiting-time = 0..4294967295 ; in milliseconds
  ttl = 0..4294967295 ; in milliseconds

  locator-option /= [O_IPv4_LOCATOR, ipv4-address,
                     transport-proto, port-number]
  ipv4-address = bytes .size 4

  locator-option /= [O_IPv6_LOCATOR, ipv6-address,
                     transport-proto, port-number]
  ipv6-address = bytes .size 16

  locator-option /= [O_FQDN_LOCATOR, text, transport-proto, port-number]

  transport-proto = IPPROTO_TCP / IPPROTO_UDP

Bormann, et al.          Expires March 17, 2017                [Page 44]
Internet-Draft                    GRASP                   September 2016

  IPPROTO_TCP = 6
  IPPROTO_UDP = 17
  port-number = 0..65535

  locator-option /= [O_URI_LOCATOR, text]

  initiator = ipv4-address / ipv6-address

  objective-flags = uint .bits objective-flag

  objective-flag = &(
   F_DISC: 0 ; valid for discovery only
   F_NEG: 1 ; valid for discovery and negotiation
   F_SYNCH: 2) ; valid for discovery and synchronization

  objective = [objective-name, objective-flags, loop-count, ?any]

  objective-name = text ;see specification for uniqueness rules

  loop-count = 0..255

  ; Constants for message types and option types

  M_NOOP = 0
  M_DISCOVERY = 1
  M_RESPONSE = 2
  M_REQ_NEG = 3
  M_REQ_SYN = 4
  M_NEGOTIATE = 5
  M_END = 6
  M_WAIT = 7
  M_SYNCH = 8
  M_FLOOD = 9

  O_DIVERT = 100
  O_ACCEPT = 101
  O_DECLINE = 102
  O_IPv6_LOCATOR = 103
  O_IPv4_LOCATOR = 104
  O_FQDN_LOCATOR = 105
  O_URI_LOCATOR = 106
  <CODE ENDS>

7.  IANA Considerations

   This document defines the Generic Autonomic Signaling Protocol
   (GRASP).

Bormann, et al.          Expires March 17, 2017                [Page 45]
Internet-Draft                    GRASP                   September 2016

   Section 3.5 explains the following link-local multicast addresses,
   which IANA is requested to assign for use by GRASP:

   ALL_GRASP_NEIGHBOR multicast address  (IPv6): (TBD1).  Assigned in
      the IPv6 Link-Local Scope Multicast Addresses registry.

   ALL_GRASP_NEIGHBOR multicast address  (IPv4): (TBD2).  Assigned in
      the IPv4 Multicast Local Network Control Block.

   Section 3.5 explains the following User Port, which IANA is requested
   to assign for use by GRASP for both UDP and TCP:

   GRASP_LISTEN_PORT: (TBD3)
   Service Name: Generic Autonomic Signaling Protocol (GRASP)
   Transport Protocols: UDP, TCP
   Assignee: iesg@ietf.org
   Contact: chair@ietf.org
   Description: See Section 3.5
   Reference: RFC XXXX (this document)

   The IANA is requested to create a GRASP Parameter Registry including
   two registry tables.  These are the GRASP Messages and Options
   Table and the GRASP Objective Names Table.

   GRASP Messages and Options Table.  The values in this table are names
   paired with decimal integers.  Future values MUST be assigned using
   the Standards Action policy defined by [RFC5226].  The following
   initial values are assigned by this document:

   M_NOOP = 0
   M_DISCOVERY = 1
   M_RESPONSE = 2
   M_REQ_NEG = 3
   M_REQ_SYN = 4
   M_NEGOTIATE = 5
   M_END = 6
   M_WAIT = 7
   M_SYNCH = 8
   M_FLOOD = 9

   O_DIVERT = 100
   O_ACCEPT = 101
   O_DECLINE = 102
   O_IPv6_LOCATOR = 103
   O_IPv4_LOCATOR = 104
   O_FQDN_LOCATOR = 105
   O_URI_LOCATOR = 106

Bormann, et al.          Expires March 17, 2017                [Page 46]
Internet-Draft                    GRASP                   September 2016

   GRASP Objective Names Table.  The values in this table are UTF-8
   strings.  Future values MUST be assigned using the Specification
   Required policy defined by [RFC5226].  The following initial values
   are assigned by this document:

    EX0
    EX1
    EX2
    EX3
    EX4
    EX5
    EX6
    EX7
    EX8
    EX9

8.  Acknowledgements

   A major contribution to the original version of this document was
   made by Sheng Jiang.

   Valuable comments were received from Michael Behringer, Jeferson
   Campos Nobre, Laurent Ciavaglia, Zongpeng Du, Toerless Eckert, Yu Fu,
   Joel Halpern, Zhenbin Li, Dimitri Papadimitriou, Pierre Peloso,
   Reshad Rahman, Michael Richardson, Markus Stenberg, Rene Struik,
   Dacheng Zhang, and other participants in the NMRG research group and
   the ANIMA working group.

9.  References

9.1.  Normative References

   [I-D.greevenbosch-appsawg-cbor-cddl]
              Vigano, C. and H. Birkholz, "CBOR data definition language
              (CDDL): a notational convention to express CBOR data
              structures", draft-greevenbosch-appsawg-cbor-cddl-08 (work
              in progress), March 2016.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC3986]  Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
              Resource Identifier (URI): Generic Syntax", STD 66,
              RFC 3986, DOI 10.17487/RFC3986, January 2005,
              <http://www.rfc-editor.org/info/rfc3986>.

Bormann, et al.          Expires March 17, 2017                [Page 47]
Internet-Draft                    GRASP                   September 2016

   [RFC4086]  Eastlake 3rd, D., Schiller, J., and S. Crocker,
              "Randomness Requirements for Security", BCP 106, RFC 4086,
              DOI 10.17487/RFC4086, June 2005,
              <http://www.rfc-editor.org/info/rfc4086>.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <http://www.rfc-editor.org/info/rfc5246>.

   [RFC5280]  Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
              Housley, R., and W. Polk, "Internet X.509 Public Key
              Infrastructure Certificate and Certificate Revocation List
              (CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
              <http://www.rfc-editor.org/info/rfc5280>.

   [RFC6347]  Rescorla, E. and N. Modadugu, "Datagram Transport Layer
              Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347,
              January 2012, <http://www.rfc-editor.org/info/rfc6347>.

   [RFC7049]  Bormann, C. and P. Hoffman, "Concise Binary Object
              Representation (CBOR)", RFC 7049, DOI 10.17487/RFC7049,
              October 2013, <http://www.rfc-editor.org/info/rfc7049>.

   [RFC7217]  Gont, F., "A Method for Generating Semantically Opaque
              Interface Identifiers with IPv6 Stateless Address
              Autoconfiguration (SLAAC)", RFC 7217,
              DOI 10.17487/RFC7217, April 2014,
              <http://www.rfc-editor.org/info/rfc7217>.

9.2.  Informative References

   [I-D.chaparadza-intarea-igcp]
              Behringer, M., Chaparadza, R., Petre, R., Li, X., and H.
              Mahkonen, "IP based Generic Control Protocol (IGCP)",
              draft-chaparadza-intarea-igcp-00 (work in progress), July
              2011.

   [I-D.ietf-anima-autonomic-control-plane]
              Behringer, M., Eckert, T., and S. Bjarnason, "An Autonomic
              Control Plane", draft-ietf-anima-autonomic-control-
              plane-03 (work in progress), July 2016.

   [I-D.ietf-anima-bootstrapping-keyinfra]
              Pritikin, M., Richardson, M., Behringer, M., and S.
              Bjarnason, "Bootstrapping Remote Secure Key
              Infrastructures (BRSKI)", draft-ietf-anima-bootstrapping-
              keyinfra-03 (work in progress), June 2016.

Bormann, et al.          Expires March 17, 2017                [Page 48]
Internet-Draft                    GRASP                   September 2016

   [I-D.ietf-anima-reference-model]
              Behringer, M., Carpenter, B., Eckert, T., Ciavaglia, L.,
              Pierre, P., Liu, B., Nobre, J., and J. Strassner, "A
              Reference Model for Autonomic Networking", draft-ietf-
              anima-reference-model-02 (work in progress), July 2016.

   [I-D.ietf-anima-stable-connectivity]
              Eckert, T. and M. Behringer, "Using Autonomic Control
              Plane for Stable Connectivity of Network OAM", draft-ietf-
              anima-stable-connectivity-01 (work in progress), July
              2016.

   [I-D.ietf-netconf-restconf]
              Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", draft-ietf-netconf-restconf-16 (work in
              progress), August 2016.

   [I-D.liang-iana-pen]
              Liang, P., Melnikov, A., and D. Conrad, "Private
              Enterprise Number (PEN) practices and Internet Assigned
              Numbers Authority (IANA) registration considerations",
              draft-liang-iana-pen-06 (work in progress), July 2015.

   [I-D.stenberg-anima-adncp]
              Stenberg, M., "Autonomic Distributed Node Consensus
              Protocol", draft-stenberg-anima-adncp-00 (work in
              progress), March 2015.

   [RFC2205]  Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S.
              Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
              Functional Specification", RFC 2205, DOI 10.17487/RFC2205,
              September 1997, <http://www.rfc-editor.org/info/rfc2205>.

   [RFC2334]  Luciani, J., Armitage, G., Halpern, J., and N. Doraswamy,
              "Server Cache Synchronization Protocol (SCSP)", RFC 2334,
              DOI 10.17487/RFC2334, April 1998,
              <http://www.rfc-editor.org/info/rfc2334>.

   [RFC2608]  Guttman, E., Perkins, C., Veizades, J., and M. Day,
              "Service Location Protocol, Version 2", RFC 2608,
              DOI 10.17487/RFC2608, June 1999,
              <http://www.rfc-editor.org/info/rfc2608>.

   [RFC2865]  Rigney, C., Willens, S., Rubens, A., and W. Simpson,
              "Remote Authentication Dial In User Service (RADIUS)",
              RFC 2865, DOI 10.17487/RFC2865, June 2000,
              <http://www.rfc-editor.org/info/rfc2865>.

Bormann, et al.          Expires March 17, 2017                [Page 49]
Internet-Draft                    GRASP                   September 2016

   [RFC3209]  Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
              and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
              Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
              <http://www.rfc-editor.org/info/rfc3209>.

   [RFC3315]  Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
              C., and M. Carney, "Dynamic Host Configuration Protocol
              for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July
              2003, <http://www.rfc-editor.org/info/rfc3315>.

   [RFC3416]  Presuhn, R., Ed., "Version 2 of the Protocol Operations
              for the Simple Network Management Protocol (SNMP)",
              STD 62, RFC 3416, DOI 10.17487/RFC3416, December 2002,
              <http://www.rfc-editor.org/info/rfc3416>.

   [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              DOI 10.17487/RFC4861, September 2007,
              <http://www.rfc-editor.org/info/rfc4861>.

   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              DOI 10.17487/RFC5226, May 2008,
              <http://www.rfc-editor.org/info/rfc5226>.

   [RFC5971]  Schulzrinne, H. and R. Hancock, "GIST: General Internet
              Signalling Transport", RFC 5971, DOI 10.17487/RFC5971,
              October 2010, <http://www.rfc-editor.org/info/rfc5971>.

   [RFC6206]  Levis, P., Clausen, T., Hui, J., Gnawali, O., and J. Ko,
              "The Trickle Algorithm", RFC 6206, DOI 10.17487/RFC6206,
              March 2011, <http://www.rfc-editor.org/info/rfc6206>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <http://www.rfc-editor.org/info/rfc6241>.

   [RFC6733]  Fajardo, V., Ed., Arkko, J., Loughney, J., and G. Zorn,
              Ed., "Diameter Base Protocol", RFC 6733,
              DOI 10.17487/RFC6733, October 2012,
              <http://www.rfc-editor.org/info/rfc6733>.

   [RFC6762]  Cheshire, S. and M. Krochmal, "Multicast DNS", RFC 6762,
              DOI 10.17487/RFC6762, February 2013,
              <http://www.rfc-editor.org/info/rfc6762>.

Bormann, et al.          Expires March 17, 2017                [Page 50]
Internet-Draft                    GRASP                   September 2016

   [RFC6763]  Cheshire, S. and M. Krochmal, "DNS-Based Service
              Discovery", RFC 6763, DOI 10.17487/RFC6763, February 2013,
              <http://www.rfc-editor.org/info/rfc6763>.

   [RFC6887]  Wing, D., Ed., Cheshire, S., Boucadair, M., Penno, R., and
              P. Selkirk, "Port Control Protocol (PCP)", RFC 6887,
              DOI 10.17487/RFC6887, April 2013,
              <http://www.rfc-editor.org/info/rfc6887>.

   [RFC7228]  Bormann, C., Ersue, M., and A. Keranen, "Terminology for
              Constrained-Node Networks", RFC 7228,
              DOI 10.17487/RFC7228, May 2014,
              <http://www.rfc-editor.org/info/rfc7228>.

   [RFC7558]  Lynn, K., Cheshire, S., Blanchet, M., and D. Migault,
              "Requirements for Scalable DNS-Based Service Discovery
              (DNS-SD) / Multicast DNS (mDNS) Extensions", RFC 7558,
              DOI 10.17487/RFC7558, July 2015,
              <http://www.rfc-editor.org/info/rfc7558>.

   [RFC7575]  Behringer, M., Pritikin, M., Bjarnason, S., Clemm, A.,
              Carpenter, B., Jiang, S., and L. Ciavaglia, "Autonomic
              Networking: Definitions and Design Goals", RFC 7575,
              DOI 10.17487/RFC7575, June 2015,
              <http://www.rfc-editor.org/info/rfc7575>.

   [RFC7576]  Jiang, S., Carpenter, B., and M. Behringer, "General Gap
              Analysis for Autonomic Networking", RFC 7576,
              DOI 10.17487/RFC7576, June 2015,
              <http://www.rfc-editor.org/info/rfc7576>.

   [RFC7787]  Stenberg, M. and S. Barth, "Distributed Node Consensus
              Protocol", RFC 7787, DOI 10.17487/RFC7787, April 2016,
              <http://www.rfc-editor.org/info/rfc7787>.

   [RFC7788]  Stenberg, M., Barth, S., and P. Pfister, "Home Networking
              Control Protocol", RFC 7788, DOI 10.17487/RFC7788, April
              2016, <http://www.rfc-editor.org/info/rfc7788>.

Appendix A.  Open Issues

   o  7.  Cross-check against other ANIMA WG documents for consistency
      and gaps.

Bormann, et al.          Expires March 17, 2017                [Page 51]
Internet-Draft                    GRASP                   September 2016

Appendix B.  Closed Issues [RFC Editor: Please remove]

   o  1.  UDP vs TCP: For now, this specification suggests UDP and TCP
      as message transport mechanisms.  This is not clarified yet.  UDP
      is good for short conversations, is necessary for multicast
      discovery, and generally fits the discovery and divert scenarios
      well.  However, it will cause problems with large messages.  TCP
      is good for stable and long sessions, with a little bit of time
      consumption during the session establishment stage.  If messages
      exceed a reasonable MTU, a TCP mode will be required in any case.
      This question may be affected by the security discussion.

      RESOLVED by specifying UDP for short message and TCP for longer
      one.

   o  2.  DTLS or TLS vs built-in security mechanism.  For now, this
      specification has chosen a PKI based built-in security mechanism
      based on asymmetric cryptography.  However, (D)TLS might be chosen
      as security solution to avoid duplication of effort.  It also
      allows essentially similar security for short messages over UDP
      and longer ones over TCP.  The implementation trade-offs are
      different.  The current approach requires expensive asymmetric
      cryptographic calculations for every message.  (D)TLS has startup
      overheads but cheaper crypto per message.  DTLS is less mature
      than TLS.

      RESOLVED by specifying external security (ACP or (D)TLS).

   o  The following open issues applied only if the original security
      model was retained:

      *  2.1.  For replay protection, GRASP currently requires every
         participant to have an NTP-synchronized clock.  Is this OK for
         low-end devices, and how does it work during device
         bootstrapping?  We could take the Timestamp out of signature
         option, to become an independent and OPTIONAL (or RECOMMENDED)
         option.

      *  2.2.  The Signature Option states that this option could be any
         place in a message.  Wouldn't it be better to specify a
         position (such as the end)?  That would be much simpler to
         implement.

      RESOLVED by changing security model.

   o  3.  DoS Attack Protection needs work.

      RESOLVED by adding text.

Bormann, et al.          Expires March 17, 2017                [Page 52]
Internet-Draft                    GRASP                   September 2016

   o  4.  Should we consider preferring a text-based approach to
      discovery (after the initial discovery needed for bootstrapping)?
      This could be a complementary mechanism for multicast based
      discovery, especially for a very large autonomic network.
      Centralized registration could be automatically deployed
      incrementally.  At the very first stage, the repository could be
      empty; then it could be filled in by the objectives discovered by
      different devices (for example using Dynamic DNS Update).  The
      more records are stored in the repository, the less the multicast-
      based discovery is needed.  However, if we adopt such a mechanism,
      there would be challenges: stateful solution, and security.

      RESOLVED for now by adding optional use of DNS-SD by ASAs.
      Subsequently removed by editors as irrelevant to GRASP istelf.

   o  5.  Need to expand description of the minimum requirements for the
      specification of an individual discovery, synchronization or
      negotiation objective.

      RESOLVED for now by extra wording.

   o  6.  Use case and protocol walkthrough.  A description of how a
      node starts up, performs discovery, and conducts negotiation and
      synchronisation for a sample use case would help readers to
      understand the applicability of this specification.  Maybe it
      should be an artificial use case or maybe a simple real one, based
      on a conceptual API.  However, the authors have not yet decided
      whether to have a separate document or have it in the protocol
      document.

      RESOLVED: recommend a separate document.

   o  8.  Consideration of ADNCP proposal.

      RESOLVED by adding optional use of DNCP for flooding-type
      synchronization.

   o  9.  Clarify how a GDNP instance knows whether it is running inside
      the ACP.  (Sheng)

      RESOLVED by improved text.

   o  10.  Clarify how a non-ACP GDNP instance initiates (D)TLS.
      (Sheng)

      RESOLVED by improved text and declaring DTLS out of scope for this
      draft.

Bormann, et al.          Expires March 17, 2017                [Page 53]
Internet-Draft                    GRASP                   September 2016

   o  11.  Clarify how UDP/TCP choice is made.  (Sheng) [Like DNS? -
      Brian]

      RESOLVED by improved text.

   o  12.  Justify that IP address within ACP or (D)TLS environment is
      sufficient to prove AN identity; or explain how Device Identity
      Option is used.  (Sheng)

      RESOLVED for now: we assume that all ASAs in a device are trusted
      as soon as the device is trusted, so they share credentials.  In
      that case the Device Identity Option is useless.  This needs to be
      reviewed later.

   o  13.  Emphasise that negotiation/synchronization are independent
      from discovery, although the rapid discovery mode includes the
      first step of a negotiation/synchronization.  (Sheng)

      RESOLVED by improved text.

   o  14.  Do we need an unsolicited flooding mechanism for discovery
      (for discovery results that everyone needs), to reduce scaling
      impact of flooding discovery messages?  (Toerless)

      RESOLVED: Yes, added to requirements and solution.

   o  15.  Do we need flag bits in Objective Options to distinguish
      distinguish Synchronization and Negotiation "Request" or rapid
      mode "Discovery" messages?  (Bing)

      RESOLVED: yes, work on the API showed that these flags are
      essential.

   o  16.  (Related to issue 14).  Should we revive the "unsolicited
      Response" for flooding synchronisation data?  This has to be done
      carefully due to the well-known issues with flooding, but it could
      be useful, e.g. for Intent distribution, where DNCP doesn't seem
      applicable.

      RESOLVED: Yes, see #14.

   o  17.  Ensure that the discovery mechanism is completely proof
      against loops and protected against duplicate responses.

      RESOLVED: Added loop count mechanism.

   o  18.  Discuss the handling of multiple valid discovery responses.

Bormann, et al.          Expires March 17, 2017                [Page 54]
Internet-Draft                    GRASP                   September 2016

      RESOLVED: Stated that the choice must be available to the ASA but
      GRASP implementation should pick a default.

   o  19.  Should we use a text-oriented format such as JSON/CBOR
      instead of native binary TLV format?

      RESOLVED: Yes, changed to CBOR.

   o  20.  Is the Divert option needed?  If a discovery response
      provides a valid IP address or FQDN, the recipient doesn't gain
      any extra knowledge from the Divert.  On the other hand, the
      presence of Divert informs the receiver that the target is off-
      link, which might be useful sometimes.

      RESOLVED: Decided to keep Divert option.

   o  21.  Rename the protocol as GRASP (GeneRic Autonomic Signaling
      Protocol)?

      RESOLVED: Yes, name changed.

   o  22.  Does discovery mechanism scale robustly as needed?  Need hop
      limit on relaying?

      RESOLVED: Added hop limit.

   o  23.  Need more details on TTL for caching discovery responses.

      RESOLVED: Done.

   o  24.  Do we need "fast withdrawal" of discovery responses?

      RESOLVED: This doesn't seem necessary.  If an ASA exits or stops
      supporting a given objective, peers will fail to start future
      sessions and will simply repeat discovery.

   o  25.  Does GDNP discovery meet the needs of multi-hop DNS-SD?

      RESOLVED: Decided not to consider this further as a GRASP protocol
      issue.  GRASP objectives could embed DNS-SD formats if needed.

   o  26.  Add a URL type to the locator options (for security bootstrap
      etc.)

      RESOLVED: Done, later renamed as URI.

   o  27.  Security of Flood multicasts (Section 3.3.6.1).

Bormann, et al.          Expires March 17, 2017                [Page 55]
Internet-Draft                    GRASP                   September 2016

      RESOLVED: added text.

   o  28.  Does ACP support secure link-local multicast?

      RESOLVED by new text in the Security Considerations.

   o  29.  PEN is used to distinguish vendor options.  Would it be
      better to use a domain name?  Anything unique will do.

      RESOLVED: Simplified this by removing PEN field and changing
      naming rules for objectives.

   o  30.  Does response to discovery require randomized delays to
      mitigate amplification attacks?

      RESOLVED: WG feedback is that it's unnecessary.

   o  31.  We have specified repeats for failed discovery etc.  Is that
      sufficient to deal with sleeping nodes?

      RESOLVED: WG feedback is that it's unnecessary to say more.

   o  32.  We have one-to-one synchronization and flooding
      synchronization.  Do we also need selective flooding to a subset
      of nodes?

      RESOLVED: This will be discussed as a protocol extension in a
      separate draft (draft-liu-anima-grasp-distribution).

   o  33.  Clarify if/when discovery needs to be repeated.

      RESOLVED: Done.

   o  34.  Clarify what is mandatory for running in ACP, expand
      discussion of security boundary when running with no ACP - might
      rely on the local PKI infrastructure.

      RESOLVED: Done.

   o  35.  State that role-based authorization of ASAs is out of scope
      for GRASP.  GRASP doesn't recognize/handle any "roles".

      RESOLVED: Done.

   o  36.  Reconsider CBOR definition for PEN syntax.  ( objective-name
      = text / [pen, text] ; pen = uint )

      RESOLVED: See issue 29.

Bormann, et al.          Expires March 17, 2017                [Page 56]
Internet-Draft                    GRASP                   September 2016

   o  37.  Are URI locators really needed?

      RESOLVED: Yes, e.g. for security bootstrap discovery, but added
      note that addresses are the normal case (same for FQDN locators).

   o  38.  Is Session ID sufficient to identify relayed responses?
      Isn't the originator's address needed too?

      RESOLVED: Yes, this is needed for multicast messages and their
      responses.

   o  39.  Clarify that a node will contain one GRASP instance
      supporting multiple ASAs.

      RESOLVED: Done.

   o  40.  Add a "reason" code to the DECLINE option?

      RESOLVED: Done.

   o  41.  What happens if an ASA cannot conveniently use one of the
      GRASP mechanisms?  Do we (a) add a message type to GRASP, or (b)
      simply pass the discovery results to the ASA so that it can open
      its own socket?

      RESOLVED: Both would be possible, but (b) is preferred.

   o  42.  Do we need a feature whereby an ASA can bypass the ACP and
      use the data plane for efficiency/throughput?  This would require
      discovery to return non-ACP addresses and would evade ACP
      security.

      RESOLVED: This is considered out of scope for GRASP, but a comment
      has been added in security considerations.

   o  43.  Rapid mode synchronization and negotiation is currently
      limited to a single objective for simplicity of design and
      implementation.  A future consideration is to allow multiple
      objectives in rapid mode for greater efficiency.

      RESOLVED: This is considered out of scope for this version.

   o  44.  In requirement T9, the words that encryption "may not be
      required in all deployments" were removed.  Is that OK?.

      RESOLVED: No objections.

Bormann, et al.          Expires March 17, 2017                [Page 57]
Internet-Draft                    GRASP                   September 2016

   o  45.  Device Identity Option is unused.  Can we remove it
      completely?.

      RESOLVED: No objections.  Done.

   o  46.  The 'initiator' field in DISCOVER, RESPONSE and FLOOD
      messages is intended to assist in loop prevention.  However, we
      also have the loop count for that.  Also, if we create a new
      Session ID each time a DISCOVER or FLOOD is relayed, that ID can
      be disambiguated by recipients.  It would be simpler to remove the
      initiator from the messages, making parsing more uniform.  Is that
      OK?

      RESOLVED: Yes. Done.

   o  47.  REQUEST is a dual purpose message (request negotiation or
      request synchronization).  Would it be better to split this into
      two different messages (and adjust various message names
      accordingly)?

      RESOLVED: Yes. Done.

   o  48.  Should the Appendix "Capability Analysis of Current
      Protocols" be deleted before RFC publication?

      RESOLVED: No (per WG meeting at IETF 96).

   o  49.  Section 3.3.1 Should say more about signaling between two
      autonomic networks/domains.

      RESOLVED: Description of separate GRASP instance added.

   o  50.  Is Rapid mode limited to on-link only?  What happens if first
      discovery responder does not support Rapid Mode?  Section 3.3.5,
      Section 3.3.6)

      RESOLVED: Not limited to on-link.  First responder wins.

   o  51.  Should flooded objectives have a time-to-live before they are
      deleted from the flood cache?  And should they be tagged in the
      cache with their source locator?

      RESOLVED: TTL added to Flood (and Discovery Response) messages.
      Cached flooded objectives must be tagged with their originating
      ASA locator, and multiple copies must be kept if necessary.

   o  52.  Describe in detail what is allowed and disallowed in an
      insecure instance of GRASP.

Bormann, et al.          Expires March 17, 2017                [Page 58]
Internet-Draft                    GRASP                   September 2016

      RESOLVED: Done.

   o  53.  Tune IANA Considerations to support early assignment request.

      RESOLVED: Done.

Appendix C.  Change log [RFC Editor: Please remove]

   draft-ietf-anima-grasp-07, 2016-09-13:

   Protocol change: Added TTL field to Flood message (issue 51).

   Protocol change: Added Locator option to Flood message (issue 51).

   Protocol change: Added TTL field to Discovery Response message
   (corrollary to issue 51).

   Clarified details of rapid mode (issues 43 and 50).

   Description of inter-domain GRASP instance added (issue 49).

   Description of limited security GRASP instances added (issue 52).

   Strengthened advice to use TCP rather than UDP.

   Updated IANA considerations and text about well-known port usage
   (issue 53).

   Amended text about ASA authorization and roles to allow for
   overlapping ASAs.

   Added text recommending that Flood should be repeated periodically.

   Editorial fixes.

   draft-ietf-anima-grasp-06, 2016-06-27:

   Added text on discovery cache timeouts.

   Noted that ASAs that are only initiators do not need to respond to
   discovery message.

   Added text on unexpected address changes.

   Added text on robust implementation.

   Clarifications and editorial fixes for numerous review comments

Bormann, et al.          Expires March 17, 2017                [Page 59]
Internet-Draft                    GRASP                   September 2016

   Added open issues for some review comments.

   draft-ietf-anima-grasp-05, 2016-05-13:

   Noted in requirement T1 that it should be possible to implement ASAs
   independently as user space programs.

   Protocol change: Added protocol number and port to discovery
   response.  Updated protocol description, CDDL and IANA considerations
   accordingly.

   Clarified that discovery and flood multicasts are handled by the
   GRASP kernel, not directly by ASAs.

   Clarified that a node may discover an objective without supporting it
   for synchronization or negotiation.

   Added Implementation Status section.

   Added reference to SCSP.

   Editorial fixes.

   draft-ietf-anima-grasp-04, 2016-03-11:

   Protocol change: Restored initiator field in certain messages and
   adjusted relaying rules to provide complete loop detection.

   Updated IANA Considerations.

   draft-ietf-anima-grasp-03, 2016-02-24:

   Protocol change: Removed initiator field from certain messages and
   adjusted relaying requirement to simplify loop detection.  Also
   clarified narrative explanation of discovery relaying.

   Protocol change: Split Request message into two (Request Negotiation
   and Request Synchronization) and updated other message names for
   clarity.

   Protocol change: Dropped unused Device ID option.

   Further clarified text on transport layer usage.

   New text about multicast insecurity in Security Considerations.

   Various other clarifications and editorial fixes, including moving
   some material to Appendix.

Bormann, et al.          Expires March 17, 2017                [Page 60]
Internet-Draft                    GRASP                   September 2016

   draft-ietf-anima-grasp-02, 2016-01-13:

   Resolved numerous issues according to WG discussions.

   Renumbered requirements, added D9.

   Protocol change: only allow one objective in rapid mode.

   Protocol change: added optional error string to DECLINE option.

   Protocol change: removed statement that seemed to say that a Request
   not preceded by a Discovery should cause a Discovery response.  That
   made no sense, because there is no way the initiator would know where
   to send the Request.

   Protocol change: Removed PEN option from vendor objectives, changed
   naming rule accordingly.

   Protocol change: Added FLOOD message to simplify coding.

   Protocol change: Added SYNCH message to simplify coding.

   Protocol change: Added initiator id to DISCOVER, RESPONSE and FLOOD
   messages.  But also allowed the relay process for DISCOVER and FLOOD
   to regenerate a Session ID.

   Protocol change: Require that discovered addresses must be global
   (except during bootstrap).

   Protocol change: Receiver of REQUEST message must close socket if no
   ASA is listening for the objective.

   Protocol change: Simplified Waiting message.

   Protocol change: Added No Operation message.

   Renamed URL locator type as URI locator type.

   Updated CDDL definition.

   Various other clarifications and editorial fixes.

   draft-ietf-anima-grasp-01, 2015-10-09:

   Updated requirements after list discussion.

   Changed from TLV to CBOR format - many detailed changes, added co-
   author.

Bormann, et al.          Expires March 17, 2017                [Page 61]
Internet-Draft                    GRASP                   September 2016

   Tightened up loop count and timeouts for various cases.

   Noted that GRASP does not provide transactional integrity.

   Various other clarifications and editorial fixes.

   draft-ietf-anima-grasp-00, 2015-08-14:

   File name and protocol name changed following WG adoption.

   Added URL locator type.

   draft-carpenter-anima-gdn-protocol-04, 2015-06-21:

   Tuned wording around hierarchical structure.

   Changed "device" to "ASA" in many places.

   Reformulated requirements to be clear that the ASA is the main
   customer for signaling.

   Added requirement for flooding unsolicited synch, and added it to
   protocol spec.  Recognized DNCP as alternative for flooding synch
   data.

   Requirements clarified, expanded and rearranged following design team
   discussion.

   Clarified that GDNP discovery must not be a prerequisite for GDNP
   negotiation or synchronization (resolved issue 13).

   Specified flag bits for objective options (resolved issue 15).

   Clarified usage of ACP vs TLS/DTLS and TCP vs UDP (resolved issues
   9,10,11).

   Updated DNCP description from latest DNCP draft.

   Editorial improvements.

   draft-carpenter-anima-gdn-protocol-03, 2015-04-20:

   Removed intrinsic security, required external security

   Format changes to allow DNCP co-existence

   Recognized DNS-SD as alternative discovery method.

Bormann, et al.          Expires March 17, 2017                [Page 62]
Internet-Draft                    GRASP                   September 2016

   Editorial improvements

   draft-carpenter-anima-gdn-protocol-02, 2015-02-19:

   Tuned requirements to clarify scope,

   Clarified relationship between types of objective,

   Clarified that objectives may be simple values or complex data
   structures,

   Improved description of objective options,

   Added loop-avoidance mechanisms (loop count and default timeout,
   limitations on discovery relaying and on unsolicited responses),

   Allow multiple discovery objectives in one response,

   Provided for missing or multiple discovery responses,

   Indicated how modes such as "dry run" should be supported,

   Minor editorial and technical corrections and clarifications,

   Reorganized future work list.

   draft-carpenter-anima-gdn-protocol-01, restructured the logical flow
   of the document, updated to describe synchronization completely, add
   unsolicited responses, numerous corrections and clarifications,
   expanded future work list, 2015-01-06.

   draft-carpenter-anima-gdn-protocol-00, combination of draft-jiang-
   config-negotiation-ps-03 and draft-jiang-config-negotiation-protocol-
   02, 2014-10-08.

Appendix D.  Capability Analysis of Current Protocols

   This appendix discusses various existing protocols with properties
   related to the requirements described in Section 2.  The purpose is
   to evaluate whether any existing protocol, or a simple combination of
   existing protocols, can meet those requirements.

   Numerous protocols include some form of discovery, but these all
   appear to be very specific in their applicability.  Service Location
   Protocol (SLP) [RFC2608] provides service discovery for managed
   networks, but requires configuration of its own servers.  DNS-SD
   [RFC6763] combined with mDNS [RFC6762] provides service discovery for
   small networks with a single link layer.  [RFC7558] aims to extend

Bormann, et al.          Expires March 17, 2017                [Page 63]
Internet-Draft                    GRASP                   September 2016

   this to larger autonomous networks but this is not yet standardized.
   However, both SLP and DNS-SD appear to target primarily application
   layer services, not the layer 2 and 3 objectives relevant to basic
   network configuration.  Both SLP and DNS-SD are text-based protocols.

   Routing protocols are mainly one-way information announcements.  The
   receiver makes independent decisions based on the received
   information and there is no direct feedback information to the
   announcing peer.  This remains true even though the protocol is used
   in both directions between peer routers; there is state
   synchronization, but no negotiation, and each peer runs its route
   calculations independently.

   Simple Network Management Protocol (SNMP) [RFC3416] uses a command/
   response model not well suited for peer negotiation.  Network
   Configuration Protocol (NETCONF) [RFC6241] uses an RPC model that
   does allow positive or negative responses from the target system, but
   this is still not adequate for negotiation.

   There are various existing protocols that have elementary negotiation
   abilities, such as Dynamic Host Configuration Protocol for IPv6
   (DHCPv6) [RFC3315], Neighbor Discovery (ND) [RFC4861], Port Control
   Protocol (PCP) [RFC6887], Remote Authentication Dial In User Service
   (RADIUS) [RFC2865], Diameter [RFC6733], etc.  Most of them are
   configuration or management protocols.  However, they either provide
   only a simple request/response model in a master/slave context or
   very limited negotiation abilities.

   There are some signaling protocols with an element of negotiation.
   For example Resource ReSerVation Protocol (RSVP) [RFC2205] was
   designed for negotiating quality of service parameters along the path
   of a unicast or multicast flow.  RSVP is a very specialised protocol
   aimed at end-to-end flows.  However, it has some flexibility, having
   been extended for MPLS label distribution [RFC3209].  A more generic
   design is General Internet Signalling Transport (GIST) [RFC5971], but
   it is complex, tries to solve many problems, and is also aimed at
   per-flow signaling across many hops rather than at device-to-device
   signaling.  However, we cannot completely exclude extended RSVP or
   GIST as a synchronization and negotiation protocol.  They do not
   appear to be directly useable for peer discovery.

   We now consider two protocols that are works in progress at the time
   of this writing.  Firstly, RESTCONF [I-D.ietf-netconf-restconf] is a
   protocol intended to convey NETCONF information expressed in the YANG
   language via HTTP, including the ability to transit HTML
   intermediaries.  While this is a powerful approach in the context of
   centralised configuration of a complex network, it is not well
   adapted to efficient interactive negotiation between peer devices,

Bormann, et al.          Expires March 17, 2017                [Page 64]
Internet-Draft                    GRASP                   September 2016

   especially simple ones that might not include YANG processing
   already.

   Secondly, we consider Distributed Node Consensus Protocol (DNCP)
   [RFC7787].  This is defined as a generic form of state
   synchronization protocol, with a proposed usage profile being the
   Home Networking Control Protocol (HNCP) [RFC7788] for configuring
   Homenet routers.  A specific application of DNCP for autonomic
   networking was proposed in [I-D.stenberg-anima-adncp].

   DNCP "is designed to provide a way for each participating node to
   publish a set of TLV (Type-Length-Value) tuples, and to provide a
   shared and common view about the data published... DNCP is most
   suitable for data that changes only infrequently... If constant rapid
   state changes are needed, the preferable choice is to use an
   additional point-to-point channel..."

   Specific features of DNCP include:

   o  Every participating node has a unique node identifier.

   o  DNCP messages are encoded as a sequence of TLV objects, sent over
      unicast UDP or TCP, with or without (D)TLS security.

   o  Multicast is used only for discovery of DNCP neighbors when lower
      security is acceptable.

   o  Synchronization of state is maintained by a flooding process using
      the Trickle algorithm.  There is no bilateral synchronization or
      negotiation capability.

   o  The HNCP profile of DNCP is designed to operate between directly
      connected neighbors on a shared link using UDP and link-local IPv6
      addresses.

   DNCP does not meet the needs of a general negotiation protocol,
   because it is designed specifically for flooding synchronization.
   Also, in its HNCP profile it is limited to link-local messages and to
   IPv6.  However, at the minimum it is a very interesting test case for
   this style of interaction between devices without needing a central
   authority, and it is a proven method of network-wide state
   synchronization by flooding.

   The Server Cache Synchronization Protocol (SCSP) [RFC2334] also
   describes a method for cache synchronization and cache replication
   among a group of nodes.

Bormann, et al.          Expires March 17, 2017                [Page 65]
Internet-Draft                    GRASP                   September 2016

   A proposal was made some years ago for an IP based Generic Control
   Protocol (IGCP) [I-D.chaparadza-intarea-igcp].  This was aimed at
   information exchange and negotiation but not directly at peer
   discovery.  However, it has many points in common with the present
   work.

   None of the above solutions appears to completely meet the needs of
   generic discovery, state synchronization and negotiation in a single
   solution.  Many of the protocols assume that they are working in a
   traditional top-down or north-south scenario, rather than a fluid
   peer-to-peer scenario.  Most of them are specialized in one way or
   another.  As a result, we have not identified a combination of
   existing protocols that meets the requirements in Section 2.  Also,
   we have not identified a path by which one of the existing protocols
   could be extended to meet the requirements.

Authors' Addresses

   Carsten Bormann
   Universitaet Bremen TZI
   Postfach 330440
   D-28359 Bremen
   Germany

   Email: cabo@tzi.org

   Brian Carpenter (editor)
   Department of Computer Science
   University of Auckland
   PB 92019
   Auckland  1142
   New Zealand

   Email: brian.e.carpenter@gmail.com

   Bing Liu (editor)
   Huawei Technologies Co., Ltd
   Q14, Huawei Campus
   No.156 Beiqing Road
   Hai-Dian District, Beijing  100095
   P.R. China

   Email: leo.liubing@huawei.com

Bormann, et al.          Expires March 17, 2017                [Page 66]