Common YANG Data Types for Layer 0 Networks
draft-ietf-ccamp-rfc9093-bis-15
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Active".
|
|
|---|---|---|---|
| Authors | Sergio Belotti , Italo Busi , Dieter Beller , Esther Le Rouzic , Aihua Guo | ||
| Last updated | 2025-07-10 (Latest revision 2025-06-17) | ||
| Replaces | draft-ietf-ccamp-layer0-types-ext | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
YANGDOCTORS Early review
(of
-13)
by Joe Clarke
Ready w/issues
YANGDOCTORS IETF Last Call review
(of
-04)
by Joe Clarke
Ready w/issues
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | Submitted to IESG for Publication | |
| Document shepherd | Daniele Ceccarelli | ||
| Shepherd write-up | Show Last changed 2025-04-09 | ||
| IESG | IESG state | IESG Evaluation::Revised I-D Needed | |
| Consensus boilerplate | Yes | ||
| Telechat date |
(None)
Has enough positions to pass. |
||
| Responsible AD | Ketan Talaulikar | ||
| Send notices to | dceccare@cisco.com | ||
| IANA | IANA review state | IANA OK - Actions Needed | |
| IANA expert review state | Expert Reviews OK |
draft-ietf-ccamp-rfc9093-bis-15
CCAMP Working Group S. Belotti, Ed.
Internet-Draft Nokia
Obsoletes: 9093 (if approved) I. Busi, Ed.
Intended status: Standards Track Huawei
Expires: 19 December 2025 D. Beller, Ed.
Nokia
E. Le Rouzic
Orange
A. Guo
Futurewei Technologies
17 June 2025
Common YANG Data Types for Layer 0 Networks
draft-ietf-ccamp-rfc9093-bis-15
Abstract
This document defines a collection of common data types, identities,
and groupings in the YANG data modeling language. These common types
and groupings, derived from the built-in YANG data types, identities,
and groupings are intended to be imported by modules that model
Optical Layer 0 configuration and state capabilities, such as
Wavelength Switched Optical Networks (WSONs) and flexi-grid Dense
Wavelength Division Multiplexing (DWDM) networks.
This document obsoletes RFC 9093 by replacing the YANG module it
contained with a new revision that includes additional YANG data
types, identities and groupings.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 19 December 2025.
Belotti, et al. Expires 19 December 2025 [Page 1]
Internet-Draft L0 Common YANG Types June 2025
Copyright Notice
Copyright (c) 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Terminology and Notations . . . . . . . . . . . . . . . . 3
1.2. Prefix in Data Node Names . . . . . . . . . . . . . . . . 3
2. Layer 0 Types Module Contents . . . . . . . . . . . . . . . . 4
2.1. WDM Label and Label Range . . . . . . . . . . . . . . . . 8
3. YANG Module for Layer 0 Types . . . . . . . . . . . . . . . . 11
4. Security Considerations . . . . . . . . . . . . . . . . . . . 58
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 59
6. References . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.1. Normative References . . . . . . . . . . . . . . . . . . 59
6.2. Informative References . . . . . . . . . . . . . . . . . 63
Appendix A. The Complete Schema Trees . . . . . . . . . . . . . 65
Appendix B. Changes from RFC 9093 . . . . . . . . . . . . . . . 70
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 74
Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 75
1. Introduction
YANG [RFC7950] is a data modeling language used to model
configuration data, state data, Remote Procedure Calls, and
notifications for network management protocols such as the Network
Configuration Protocol (NETCONF) [RFC6241]. The YANG language
supports a small set of built-in data types and provides mechanisms
to derive other types from the built-in types.
This document introduces a collection of common data types derived
from the built-in YANG data types. The derived types and groupings
are designed to be the common types applicable for modeling Traffic
Engineering (TE) features as well as non-TE features (e.g., physical
network configuration aspects) for Layer 0 optical networks in models
defined outside of this document. The applicability of Layer 0 types
Belotti, et al. Expires 19 December 2025 [Page 2]
Internet-Draft L0 Common YANG Types June 2025
specified in this document includes Wavelength Switched Optical
Networks (WSONs) [RFC6163] [ITU-T_G.694.1] and [ITU-T_G.694.2], and
flexi-grid Dense Wavelength Division Multiplexing (DWDM) networks
[RFC7698] [ITU-T_G.694.1].
This document adds new type definitions to the YANG modules and
obsoletes [RFC9093]. For further details, see the revision
statements of the YANG module in Section 3 or the summary in
Appendix B.
This document obsoletes [RFC9093] by replacing it in its entirety.
It provides a new revision of the YANG module contained in that RFC,
and retains the data types previously defined, but also adds new type
definitions to the YANG module. For further details, see Appendix B.
The YANG data model in this document conforms to the Network
Management Datastore Architecture defined in [RFC8342].
1.1. Terminology and Notations
In the context of this document, the term "layer 0" refers to the
photonic layer or WDM layer network in the architecture of the
optical transport network (OTN) as defined in [ITU-T_G.709],
[ITU-T_G.872], and [ITU-T_G.807] as opposed to the electrical
switching layers of the OTN, which are typically referred to as layer
1 (L1).
The term "layer 0" may also be used for other transport network
technologies (e.g., copper-based, radio-based, or free space optics-
based, etc.), which are outside the scope of this document.
Refer to [RFC7446] and [RFC7581] for other key terms used in this
document, and the terminology for describing YANG data models can be
found in [RFC7950].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
1.2. Prefix in Data Node Names
In this document, names of data nodes and other data model objects
are prefixed using the standard prefix associated with the
corresponding YANG imported module.
Belotti, et al. Expires 19 December 2025 [Page 3]
Internet-Draft L0 Common YANG Types June 2025
+==========+===================+===========+
| Prefix | YANG module | Reference |
+==========+===================+===========+
| te-types | ietf-te-types | [RFCYYYY] |
+----------+-------------------+-----------+
| l0-types | ietf-layer0-types | RFC XXXX |
+----------+-------------------+-----------+
Table 1: Prefixes and corresponding YANG
module
RFC Editor Note: Please replace XXXX with the RFC number assigned
to this document. Please replace YYYY with the RFC number
assigned to [I-D.ietf-teas-rfc8776-update]. Please remove this
note.
2. Layer 0 Types Module Contents
This document defines a YANG module for common Layer 0 types, ietf-
layer0-types. This module is used for WSON and flexi-grid DWDM
networks. The "ietf-layer0-types" module contains the following YANG
reusable YANG data types, identities and groupings:
l0-grid-type: A base YANG identity for the grid type as defined in
[RFC6205] and [RFC7699].
cwdm-ch-spc-type: A base YANG identity for the Coarse Wavelength
Division Multiplexing (CWDM) channel-spacing type as defined in
[RFC6205].
dwdm-ch-spc-type: A base YANG identity for the DWDM channel-spacing
type as defined in [RFC6205].
flexi-ncfg-type: A base YANG identity for the DWDM flexi-grid
Nominal Central Frequency Granularity (NCFG) type as defined in
[RFC7699].
Note that the only value for NCFG standardized in [ITU-T_G.694.1]
is 6.25GHz.
flexi-slot-width-granularity: A base YANG identity for the DWDM
flexi-grid Slot Width Granularity (SWG) type, as defined in
[RFC7699].
Note that the only value for SWG standardized in [ITU-T_G.694.1]
is 12.5GHz.
fec-type: A base YANG identity from which specific FEC (Forward
Belotti, et al. Expires 19 December 2025 [Page 4]
Internet-Draft L0 Common YANG Types June 2025
Error Correction) type identities are derived.
line-coding: A base YANG identity from which specific identities
defining the bit rate/line coding of optical tributary signals are
derived.
wavelength-assignment: A base YANG identity from which specific
identities defining the the Wavelength selection methods, as
defined in [RFC7689], are derived.
operational-mode: A YANG data type used to identify an organization
(e.g., vendor) specific mode for transceiver capability
description, as defined in Section 2.5.2 of
[I-D.ietf-ccamp-optical-impairment-topology-yang]
wson-label-start-end: The WSON label range was defined in [RFC6205],
and the generic topology model defines the label-start/label-end
in [RFC8795]. This grouping shows the WSON-specific label-start
and label-end information. See Section 2.1 for more details.
wson-label-hop: The WSON label range was defined in [RFC6205], and
the generic topology model defines the label-hop in [RFC8795].
This grouping shows the WSON-specific label-hop information. See
Section 2.1 for more details.
l0-label-range-info: A YANG grouping that defines the Layer 0 label
range information applicable for WSON as defined in [RFC6205].
The label range info is defined per priority [RFC4203].
This grouping is used in the flexi-grid DWDM by adding more flexi-
grid-specific parameters. See Section 2.1 for more details.
wson-label-step: A YANG grouping that defines label steps for WSON
as defined in [I-D.ietf-teas-rfc8776-update]. See Section 2.1 for
more details.
flexi-grid-label-start-end: The flexi-grid label range was defined
in [RFC7699], and the generic topology model defines the label-
start/label-end in [RFC8795].
This grouping shows the flexi-grid-specific label-start and label-
end information which is used to describe the range of available
nominal central frequencies. See Section 2.1 for more details.
As described in section 3.1 of [RFC8363], the range of available
nominal central frequencies is advertised for m=1, which means
that for an available central frequency n, the frequency slot from
central frequency n-1 to central frequency n+1 is available.
Belotti, et al. Expires 19 December 2025 [Page 5]
Internet-Draft L0 Common YANG Types June 2025
flexi-grid-label-hop: The flexi-grid label range was defined in
[RFC8363], and the generic topology model defines the label-hop in
[RFC8795].
This grouping shows the WSON-specific label-hop information. See
Section 2.1 for more details.
flexi-grid-label-range-info: A YANG grouping that defines flexi-grid
label range information as defined in [RFC8363]. See Section 2.1
for more details. See Section 2.1 for more details.
flexi-grid-label-step: A YANG grouping that defines flexi-grid label
steps as defined in [I-D.ietf-teas-rfc8776-update]. See
Section 2.1 for more details.
wdm-label-start-end: A YANG grouping that combines the definition of
label-start/label-end information that was defined separately in
wson-label-start-end and flexi-grid-label-start-end, to support
optical network scenarios that contain both fixed- and flexi-grid
links. See Section 2.1 for more details.
wdm-label-hop: A YANG grouping that combines the definition of label
hop information that was defined separately in wson-label-hop and
flexi-grid-label-hop, to support optical network scenarios that
contain both fixed- and flexi-grid links. See Section 2.1 for
more details.
wdm-label-range-info: A YANG grouping that combines the definition
of label range information that was defined separately in wson-
label-range-info and flexi-grid-label-range-info, to support
optical network scenarios that contain both fixed- and flexi-grid
links. See Section 2.1 for more details.
wdm-label-step: A YANG grouping that combines the definition of
label step information defined separately in wson-label-step and
flexi-grid-label-step, to support optical network scenarios that
contain both fixed- and flexi-grid links. See Section 2.1 for
more details.
transceiver-capabilities: A YANG grouping to define the transceiver
capabilities (also called "modes") needed to determine optical
signal compatibility.
When this grouping is used, the explicit-mode container shall be
augmented with a leafref to an explicit mode template with the
proper XPath, which depends from where this grouping is actually
used.
Belotti, et al. Expires 19 December 2025 [Page 6]
Internet-Draft L0 Common YANG Types June 2025
Examples of how the transceiver-capabilities grouping can be used
and augmented with a leafref to an explicit mode template are
provided in the YANG models defined in
[I-D.ietf-ccamp-optical-impairment-topology-yang] and
[I-D.ietf-ccamp-dwdm-if-param-yang].
standard-mode: A YANG grouping for the standard modes defined in
[ITU-T_G.698.2].
organizational-mode: A YANG grouping to define transponder
operational mode supported by organizations or vendors, as defined
in [I-D.ietf-ccamp-optical-impairment-topology-yang].
explicit-mode: A YANG grouping to define the list of attributes
related to the limits of the optical impairments, in case of
transceiver explicit mode, as defined in
[I-D.ietf-ccamp-optical-impairment-topology-yang].
Note that the actual portion of the spectrum occupied by an OTSi
is not explicitly reported within the explicit-mode parameters
because it can be calculated using the available-baud-rate, the
roll-off and the min-carrier-spacing attributes.
transceiver-tuning-range: A YANG grouping that defines the
transceiver tuning range, which includes the minimum and maximum
tuning frequency, as well as the frequency tuning granularity.
common-all-modes: A YANG grouping used to define the common
attributes used by all transceiver's modes.
modulation: A base YANG identity to define the different modulation
types, as defined in [ITU-T_G.Sup39]
snr: A YANG data type used to represent an (Optical) Signal-to-noise
ratio measured over 0.1 nm resolution bandwidth, as defined in
[ITU-T_G.977.1]
psd: A YANG data type used to represent a Power Spectral Density
(PSD), as defined in [ITU-T_G.9700]
penalty-value: A YANG grouping to define the penalty value for
multiple penalty types, such as Chromatic Dispersion (CD),
Polarization Mode Dispersion (PMD), as defined in [ITU-T_G.666] or
Polarization Dependent Loss(PDL)
switching-wson-lsc: A YANG identity for the Wavelength Switched
Optical Network Lambda-Switch Capable (WSON-LSC) interface
switching capability as defined in [RFC7688].
Belotti, et al. Expires 19 December 2025 [Page 7]
Internet-Draft L0 Common YANG Types June 2025
switching-flexi-grid-lsc: A YANG identity for the Flexi-Grid Lambda-
Switch Capable (Flexi-Grid-LSC) interface switching capability as
defined in [RFC8363].
It is worth noting that there is an inheritance relationship between
the Lambda-Switch Capable (LSC) switching capability, defined in
[RFC3471], and the WSON-LSC and Flexi-Grid-LSC, defined respectively
in [RFC7688] and [RFC8363]. As a consequence, the 'switching-wson-
lsc' and 'switching-flexi-grid-lsc' YANG identities are defined as
derived identities from the 'switching-lsc', defined in
[I-D.ietf-teas-rfc8776-update].
2.1. WDM Label and Label Range
As described in [RFC6205] and [RFC7699], the WDM label represents the
frequency slots assigned to a WDM Label Switched Path (LSP) on a
given WDM Link, which models an Optical Multiplex Section (OMS) Media
Channel Group (MCG) as described in
[I-D.ietf-ccamp-optical-impairment-topology-yang].
The same WDM label (which represents the frequency slots associated
with the WDM LSP) will be assigned on all the WDM Links along a
regen-free LSP path or path segment (i.e., an LSP path or path
segment which does not include any 3R regenerator). Depending on the
3R capabilities, the WDM label may or may not change at a 3R
regenerator: see Section 2.7 of
[I-D.ietf-ccamp-optical-impairment-topology-yang] for more details on
3R regenerators.
A frequency slot is defined in [ITU-T_G.694.1] as a contiguous
frequency range characterized by its nominal central frequency and
slot width. The frequency range allocated to a frequency slot is
unavailable to other frequency slots.
The definition of the frequency slot depends on the WDM grid type:
* In case of CWDM fixed-grid, defined in [ITU-T_G.694.2], the
frequency slot is defined by a fixed CWDM channel spacing (cwdm-
ch-spc-type) and by the nominal central wavelength which is
computed as described in [RFC6205]. The formula in [RFC6205] is
copied here for reader convenience:
lambda = 1471 nm + n * channel spacing (measured in nm)
where 'n' is defined in [RFC6205] as integer (positive, negative,
or 0)
Belotti, et al. Expires 19 December 2025 [Page 8]
Internet-Draft L0 Common YANG Types June 2025
* In case of DWDM fixed-grid, defined in [ITU-T_G.694.1], the
frequency slot is defined by a fixed DWDM channel spacing (dwdm-
ch-spc-type) and by the nominal central frequency, which is
computed as described in [RFC6205]. The formula in [RFC6205] is
copied here for reader convenience:
f = 193100.000 GHz + n * channel spacing (measured in GHz)
where 'n' is defined in [RFC6205] as integer (positive, negative,
or 0)
* In case of DWDM flexible-grid, defined in [ITU-T_G.694.1], the
frequency slot is defined by the slot width and by the nominal
central frequency, which are computed, based on the slot width
granularity (SWG, fixed at 12.5GHz in [ITU-T_G.694.1]), and of the
nominal central frequency granularity (NCFG, fixed at 6.25GHz in
[ITU-T_G.694.1]) respectively, as described in [RFC7698] and
[RFC7699]. The formulas in [RFC7699] can be generalized as
follows:
SW = m * SWG (measured in GHz)
f = 193100.000 GHz + N * NCFG (measured in GHz)
where 'n' is defined in [RFC7699] as integer (positive, negative,
or 0) and 'm' is defined in [RFC7698] as an integer greater than
or equal to 1.
The definition of the channel spacing, NCFG and SWG in the YANG model
have been generalized to support modelling of vendor-specific values
(e.g., finer vendor-specific granularity for NCFG and SWG).
The WDM Label Range represents the frequency slots that are available
for WDM LSPs to be set up over a given WDM Link.
The WDM Label Range is defined by augmenting the label-restriction
list, defined in [I-D.ietf-teas-rfc8776-update], with WDM technology-
specific attributes, using the l0-label-range-info grouping (for WSON
only models) or the flexi-grid-label-range-info grouping (for DWDM
flexible-grid only models) or the wdm-label-range-info grouping (for
models that support both WSON and DWDM flexible-grid).
Each entry in the label-restriction list represents either the range
of the available central wavelength values (in case of CWDM fixed-
grid) or the range of the available nominal central frequencies
values (in case of DWDM fixed or flexible grids): the grid-type
attribute defines the type of grid for each entry of the list.
Belotti, et al. Expires 19 December 2025 [Page 9]
Internet-Draft L0 Common YANG Types June 2025
In case of DWDM flexible grid, each entry in the label-restriction
list also represents the range of the supported slot width values
based on the following attributes, defined based on concepts used in
[RFC7699]:
* slot-width-granularity, which represents the minimum space between
slot widths;
* min-slot-width-factor: a multiplier of the slot width granularity,
indicating the minimum slot width supported by each entry in the
label-restriction list;
* max-slot-width-factor: a multiplier of the slot width granularity,
indicating the maximum slot width supported by each entry in the
label-restriction list.
Each entry of the label-restriction list, as defined in
[I-D.ietf-teas-rfc8776-update], defines a label-start, a label-end, a
label-step and a range-bitmap.
The label-start and label-end definitions, when used for representing
WDM label range, are augmented with WDM technology-specific
attributes, using the wson-label-start-end grouping (for WSON only
models) or the flexi-grid-label-start-end grouping (for DWDM
flexible-grid only models) or the wdm-label-start-end grouping (for
models that support both WSON and DWDM flexible-grid).
The label-step definition, when used for representing WDM label
range, is augmented with WDM technology-specific attributes, using
the wson-label-step grouping (for WSON only models) or the flexi-
grid-label-step grouping (for DWDM flexible-grid only models) or the
wdm-label-step grouping (for models that support both WSON and DWDM
flexible-grid). The label-step definition for WDM depends on the WDM
grid type:
* For CWDM and DWDM fixed grids, it describes the channel spacing,
as defined in [RFC6205];
* For DWDM flexible grids, it describes the nominal central
frequency granularity (e.g., 6,25 GHz) as well as the multiplier
for the supported values of n, as defined in [RFC7699].
Belotti, et al. Expires 19 December 2025 [Page 10]
Internet-Draft L0 Common YANG Types June 2025
3. YANG Module for Layer 0 Types
This YANG module references [RFC6205], [RFC7689], [RFC7699],
[RFC8363], [RFC9093], [ITU-T_G.666], [ITU-T_G.694.1],
[ITU-T_G.694.2], [ITU-T_G.698.2], [ITU-T_G.709], [ITU-T_G.709.2],
[ITU-T_G.709.3], [ITU-T_G.959.1] [ITU-T_G.975], [ITU-T_G.975.1],
[ITU-T_G.977.1], [ITU-T_G.9700] and [OIF_400ZR].
<CODE BEGINS> file "ietf-layer0-types@2025-02-25.yang"
module ietf-layer0-types {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-layer0-types";
prefix l0-types;
import ietf-te-types {
prefix te-types;
reference
"RFC YYYY: Common YANG Data Types for Traffic Engineering";
}
// RFC Editor: replace YYYY with actual RFC number assigned to
// [I-D.ietf-teas-rfc8776-update] and remove this note
organization
"IETF CCAMP Working Group";
contact
"WG Web: <https://datatracker.ietf.org/wg/ccamp/>
WG List: <mailto:ccamp@ietf.org>
Editor: Dieter Beller
<mailto:Dieter.Beller@nokia.com>
Editor: Sergio Belotti
<mailto:Sergio.Belotti@nokia.com>
Editor: Italo Busi
<mailto:Italo.Busi@huawei.com>
Editor: Haomian Zheng
<mailto:zhenghaomian@huawei.com>";
description
"This module defines Optical Layer 0 types. This module
provides groupings that can be applicable to Layer 0
Fixed Optical Networks (e.g., CWDM (Coarse Wavelength
Division Multiplexing) and DWDM (Dense Wavelength Division
Multiplexing)) and flexi-grid optical networks.
Copyright (c) 2025 IETF Trust and the persons identified
as authors of the code. All rights reserved.
Belotti, et al. Expires 19 December 2025 [Page 11]
Internet-Draft L0 Common YANG Types June 2025
Redistribution and use in source and binary forms, with
or without modification, is permitted pursuant to, and
subject to the license terms contained in, the Revised
BSD License set forth in Section 4.c of the IETF Trust's
Legal Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.
The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
'MAY', and 'OPTIONAL' in this document are to be interpreted as
described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
they appear in all capitals, as shown here.";
// RFC Ed.: replace XXXX with actual RFC number and remove
// this note
// replace the revision date with the module publication date
// the format is (year-month-day)
revision 2025-06-06 {
description
"To be updated";
reference
"RFC XXXX: A YANG Data Model for Layer 0 Types";
}
revision 2021-08-13 {
description
"Initial version";
reference
"RFC 9093: A YANG Data Model for Layer 0 Types";
}
/*
* Identities
*/
identity l0-grid-type {
description
"Layer 0 grid type";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC), Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
CWDM wavelength grid";
Belotti, et al. Expires 19 December 2025 [Page 12]
Internet-Draft L0 Common YANG Types June 2025
}
identity wson-grid-cwdm {
base l0-grid-type;
description
"CWDM grid";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
CWDM wavelength grid";
}
identity wson-grid-dwdm {
base l0-grid-type;
description
"DWDM grid";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC), Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity flexi-grid-dwdm {
base l0-grid-type;
description
"Flexi-grid";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity cwdm-ch-spc-type {
description
"CWDM channel-spacing type";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
CWDM wavelength grid";
}
Belotti, et al. Expires 19 December 2025 [Page 13]
Internet-Draft L0 Common YANG Types June 2025
identity cwdm-20nm {
base cwdm-ch-spc-type;
description
"20nm channel spacing";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
CWDM wavelength grid";
}
identity dwdm-ch-spc-type {
description
"DWDM channel-spacing type";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity dwdm-100ghz {
base dwdm-ch-spc-type;
description
"100 GHz channel spacing";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity dwdm-50ghz {
base dwdm-ch-spc-type;
description
"50 GHz channel spacing";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity dwdm-25ghz {
Belotti, et al. Expires 19 December 2025 [Page 14]
Internet-Draft L0 Common YANG Types June 2025
base dwdm-ch-spc-type;
description
"25 GHz channel spacing";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity dwdm-12p5ghz {
base dwdm-ch-spc-type;
description
"12.5 GHz channel spacing";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity flexi-ch-spc-type {
status deprecated;
description
"Flexi-grid channel-spacing type";
}
identity flexi-ch-spc-6p25ghz {
base flexi-ch-spc-type;
status deprecated;
description
"6.25 GHz channel spacing";
}
identity flexi-ncfg-type {
description
"Flexi-grid Nominal Central Frequency Granularity (NCFG)
type";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
Belotti, et al. Expires 19 December 2025 [Page 15]
Internet-Draft L0 Common YANG Types June 2025
identity flexi-ncfg-6p25ghz {
base flexi-ncfg-type;
description
"6.25 GHz Nominal Central Frequency Granularity (NCFG)";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity flexi-slot-width-granularity {
description
"Flexi-grid slot width granularity";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity flexi-swg-12p5ghz {
base flexi-slot-width-granularity;
description
"12.5 GHz slot width granularity";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
identity modulation {
description "base identity for modulation type";
}
identity DPSK {
base modulation;
description
"DPSK (Differential Phase Shift Keying) modulation";
}
identity QPSK {
base modulation;
description
Belotti, et al. Expires 19 December 2025 [Page 16]
Internet-Draft L0 Common YANG Types June 2025
"QPSK (Quadrature Phase Shift Keying) modulation";
}
identity DP-QPSK {
base modulation;
description
"DP-QPSK (Dual Polarization Quadrature
Phase Shift Keying) modulation";
}
identity QAM8 {
base modulation;
description
"8QAM (8 symbols Quadrature Amplitude Modulation)";
}
identity DP-QAM8 {
base modulation;
description
"DP-QAM8 (8 symbols Dual Polarization Quadrature Amplitude
Modulation)";
}
identity QAM16 {
base modulation;
description
"QAM16 (16 symbols Quadrature Amplitude Modulation)";
}
identity DP-QAM16 {
base modulation;
description
"DP-QAM16 (16 symbols Dual Polarization Quadrature Amplitude
Modulation)";
}
identity QAM32 {
base modulation;
description
"QAM32 (32 symbols Quadrature Amplitude Modulation)";
}
identity DP-QAM32 {
base modulation;
description
"DP-QAM32 (32 symbols Dual Polarization Quadrature Amplitude
Modulation)";
}
Belotti, et al. Expires 19 December 2025 [Page 17]
Internet-Draft L0 Common YANG Types June 2025
identity QAM64 {
base modulation;
description
"QAM64 (64 symbols Quadrature Amplitude Modulation)";
}
identity DP-QAM64 {
base modulation;
description
"DP-QAM64 (64 symbols Dual Polarization Quadrature Amplitude
Modulation)";
}
identity fec-type {
description
"Base identity from which specific FEC
(Forward Error Correction) type identities are derived.";
}
identity g-fec {
base fec-type;
description
"Generic Forward Error Correction (G-FEC).";
reference
"ITU-T G.975 v2.0 (10/2000): Forward error correction for
submarine systems.";
}
identity super-fec {
base fec-type;
description
"Super Forward Error Correction (S-FEC).";
reference
"ITU-T G.975.1 v1.2 (07/2013): Forward error correction for
high bit-rate DWDM submarine systems.";
}
identity no-fec {
base fec-type;
description
"No FEC";
}
identity sc-fec {
base fec-type;
description
"Staircase Forward Error Correction (SC-FEC).";
reference
Belotti, et al. Expires 19 December 2025 [Page 18]
Internet-Draft L0 Common YANG Types June 2025
"Annex A of ITU-T G.709.2 v1.1 (09/2020):OTU4 long-reach
interface.";
}
identity o-fec {
base fec-type;
description
"Open Forward Error Correction (O-FEC) which reuses the
Bose, Chaudhuri and Hocquenghem (BCH) FEC.";
reference
"Clause 16.4.4 of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
long-reach interfaces;
Annex E of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
long-reach interfaces.";
}
identity c-fec {
base fec-type;
description
"Concatenated FEC (C-FEC) that combines an outer Staircase
Forward Error Correction (SC-FEC) code and an inner
double-extended SD-FEC (128,119) Hamming code.
More details are provided in clause 15/G.709.3 where it is
called DSH instead of concatenated FEC.";
reference
"Annex A of ITU-T G.709.2 v1.1 (09/2020):OTU4 long-reach
interface;
Annex D of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
long-reach interfaces;
Clause 15 of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
long-reach interfaces.";
}
identity line-coding {
description
"Base identity to defined the bit rate/line coding of optical
tributary signals.";
reference
"Section 7.1.2 of ITU-T G.698.2 v3.0 (11/2018).";
}
identity line-coding-NRZ-2p5G {
base line-coding;
description
Belotti, et al. Expires 19 December 2025 [Page 19]
Internet-Draft L0 Common YANG Types June 2025
"The non return to zero (NRZ) bit rate/line coding used by
the optical tributary signal class NRZ 2.5G";
reference
"Section 3.2.6 of ITU-T G.959.1 v8.0 (07/2018).";
}
identity line-coding-NRZ-OTU1 {
base line-coding;
description
"The non return to zero (NRZ) bit rate/line coding used by
the Optical channel Transport Unit order 1 (OTU1) optical
tributary signals";
reference
"Section 7.2.1.2 of ITU-T G.959.1 v8.0 (07/2018).";
}
identity line-coding-NRZ-10G {
description
"The non return to zero (NRZ) bit rate/line coding used by
the optical tributary signal class NRZ 10G";
reference
"Section 3.2.7 of ITU-T G.959.1 v8.0 (07/2018).";
}
identity line-coding-NRZ-OTU2 {
base line-coding;
description
"The non return to zero (NRZ) bit rate/line coding used by
the Optical channel Transport Unit order 2 (OTU2) optical
tributary signals";
reference
"Section 7.2.1.2 of ITU-T G.959.1 v8.0 (07/2018).";
}
identity line-coding-OTL4.4-SC {
base line-coding;
description
"The bit rate/line coding used by optical tributary
signals carrying a 100G Optical Transport Unit order 4
(OTU4) with Staircase Forward Error Correction (SC FEC)
from a group of four Optical Transport Lanes (OTL).";
reference
"Section 3.2.1 of ITU-T G.698.2 v3.0 (11/2018).";
}
identity line-coding-FOIC1.4-SC {
base line-coding;
description
Belotti, et al. Expires 19 December 2025 [Page 20]
Internet-Draft L0 Common YANG Types June 2025
"The bit rate/line coding used by optical tributary signals
carrying a FlexO Interface of order C1 with 4 lanes
(FOIC1.1) with Staircase Forward Error Correction
(SC FEC).";
reference
"Section 3.2.1 of ITU-T G.698.2 v3.0 (11/2018).";
}
identity wavelength-assignment {
description
"Wavelength selection base";
reference
"RFC 7689: Signaling Extensions for Wavelength Switched
Optical Networks";
}
identity first-fit-wavelength-assignment {
base wavelength-assignment;
description
"All the available wavelengths are numbered,
and this WA (Wavelength Assignment) method chooses
the available wavelength with the lowest index";
reference
"RFC 7689: Signaling Extensions for Wavelength Switched
Optical Networks";
}
identity random-wavelength-assignment {
base wavelength-assignment;
description
"This WA method chooses an available
wavelength randomly";
reference
"RFC 7689: Signaling Extensions for Wavelength Switched
Optical Networks";
}
identity least-loaded-wavelength-assignment {
base wavelength-assignment;
description
"This WA method selects the wavelength that
has the largest residual capacity on the most loaded
link along the route (in multi-fiber networks)";
reference
"RFC 7689: Signaling Extensions for Wavelength Switched
Optical Networks";
}
Belotti, et al. Expires 19 December 2025 [Page 21]
Internet-Draft L0 Common YANG Types June 2025
identity lower-first-wavelength-assignment {
base wavelength-assignment;
description
"Allocate wavelengths in ascending order, beginning from the
lowest frequency and progressing toward the highest frequency
within the permissible frequency range.";
}
identity upper-first-wavelength-assignment {
base wavelength-assignment;
description
"Allocate wavelengths in decending order, beginning from the
highest frequency and progressing toward the lowest frequency
within the permissible frequency range.";
}
identity type-power-mode {
description
"power equalization mode used within the
OMS and its elements";
}
identity power-spectral-density {
base type-power-mode;
description
"all elements must use power spectral density (W/Hz)";
}
identity carrier-power {
base type-power-mode;
description
"all elements must use power (dBm)";
}
identity switching-wson-lsc {
base te-types:switching-lsc;
description
"Wavelength Switched Optical Network Lambda-Switch Capable
(WSON-LSC).";
reference
"Section 3 of RFC 7688: GMPLS OSPF Enhancement for Signal and
Network Element Compatibility for Wavelength Switched Optical
Networks";
}
identity switching-flexi-grid-lsc {
base te-types:switching-lsc;
description
Belotti, et al. Expires 19 December 2025 [Page 22]
Internet-Draft L0 Common YANG Types June 2025
"Flexi-grid Lambda-Switch Capable (Flexi-Grid-LSC).";
reference
"Section 4.1 of RFC 8363: GMPLS OSPF-TE Extensions in Support
of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
}
/*
* Typedefs
*/
typedef dwdm-n {
type int16;
description
"The given value 'N' is used to determine the nominal central
frequency.
The nominal central frequency, 'f', is defined by:
f = 193100.000 GHz + N x channel spacing (measured in GHz),
where 193100.000 GHz (193.100000 THz) is the ITU-T 'anchor
frequency' for transmission over the DWDM grid, and where
'channel spacing' is defined by the dwdm-ch-spc-type.";
reference
"RFC6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
typedef cwdm-n {
type int16;
description
"The given value 'N' is used to determine the nominal central
wavelength.
The nominal central wavelength is defined by:
Wavelength = 1471 nm + N x channel spacing (measured in nm)
where 1471 nm is the conventional 'anchor wavelength' for
transmission over the CWDM grid, and where 'channel spacing'
is defined by the cwdm-ch-spc-type.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
Belotti, et al. Expires 19 December 2025 [Page 23]
Internet-Draft L0 Common YANG Types June 2025
CWDM wavelength grid";
}
typedef flexi-n {
type int16;
description
"The given value 'N' is used to determine the nominal central
frequency.
The nominal central frequency, 'f', is defined by:
f = 193100.000 GHz + N x NCFG (measured in GHz),
where 193100.000 GHz (193.100000 THz) is the ITU-T 'anchor
frequency' for transmission over the DWDM grid, and where
NCFG is defined by the flexi-ncfg-type, or by the deprecated
flexi-ch-spc-type.";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
typedef flexi-m {
type uint16;
description
"The given value 'M' is used to determine the slot width.
A slot width is defined by:
slot width = M x SWG (measured in GHz),
where SWG is defined by the flexi-slot-width-granularity.";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
DWDM frequency grid";
}
typedef standard-mode {
type string;
description
"Identifies an ITU-T G.698.2 standard application code.
It MUST be a string with a format that follows the
nomenclature defined in section 5.3 of ITU-T G.698.2.";
Belotti, et al. Expires 19 December 2025 [Page 24]
Internet-Draft L0 Common YANG Types June 2025
reference
"ITU-T G.698.2 (11/2018)";
}
typedef organization-identifier {
type string;
description
"vendor/organization identifier that uses a private mode
out of already defined in G.698.2 ITU-T application-code";
reference
"Section 2.5.2 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
typedef operational-mode {
type string;
description
"Identifies an organization (e.g., vendor) specific mode.
The format of the string has to be defined by the
organization which is responsible for defining the
corresponding optical interface specification.";
reference
"Section 2.5.2 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
typedef frequency-thz {
type decimal64 {
fraction-digits 9;
}
units "THz";
description
"The DWDM frequency in THz, e.g., 193.112500000";
}
typedef frequency-ghz {
type decimal64 {
fraction-digits 6;
}
units "GHz";
description
Belotti, et al. Expires 19 December 2025 [Page 25]
Internet-Draft L0 Common YANG Types June 2025
"The DWDM frequency in GHz, e.g., 193112.500000";
}
typedef snr {
type decimal-2;
units "dB@0.1nm";
description
"(Optical) Signal to Noise Ratio measured over 0.1 nm
resolution bandwidth";
reference
"ITU-T G.977.1 (02/2021): Transverse compatible dense
wavelength division multiplexing applications for repeatered
optical fibre submarine cable systems";
}
typedef snr-or-null {
type union {
type snr;
type empty;
}
description
"(Optical) Signal to Noise Ratio measured over 0.1 nm
resolution bandwidth, when known, or an empty value when
unknown.";
}
typedef fiber-type {
type enumeration {
enum G.652 {
description
"G.652 Standard Singlemode Fiber";
}
enum G.654 {
description
"G.654 Cutoff Shifted Fiber";
}
enum G.653 {
description "G.653 Dispersion Shifted Fiber";
}
enum G.655 {
description "G.655 Non-Zero Dispersion Shifted Fiber";
}
enum G.656 {
description
"G.656 Non-Zero Dispersion for Wideband Optical Transport";
}
enum G.657 {
description
Belotti, et al. Expires 19 December 2025 [Page 26]
Internet-Draft L0 Common YANG Types June 2025
"G.657 Bend-Insensitive Fiber";
}
}
description
"ITU-T based fiber-types";
}
typedef decimal-2 {
type decimal64 {
fraction-digits 2;
}
description
"A decimal64 value with two digits.";
}
typedef decimal-2-or-null {
type union {
type decimal-2;
type empty;
}
description
"A decimal64 value with two digits, when the value is known or
an empty value when the value is not known.";
}
typedef power-gain {
type decimal-2 {
range "0..max";
}
units "dB";
description
"The gain in dB.";
}
typedef power-gain-or-null {
type union {
type power-gain;
type empty;
}
description
"The gain in dB, when it is known or an empty
value when the power gain/loss is not known.";
}
typedef power-loss {
type decimal-2 {
range "0..max";
}
Belotti, et al. Expires 19 December 2025 [Page 27]
Internet-Draft L0 Common YANG Types June 2025
units "dB";
description
"The power attenuation in dB.";
}
typedef power-loss-or-null {
type union {
type power-loss;
type empty;
}
description
"The power attenuation in dB, when it is known or an empty
value when the loss is not known.";
}
typedef power-ratio {
type decimal-2;
units "dB";
description
"The power difference in dB.";
}
typedef power-ratio-or-null {
type union {
type power-ratio;
type empty;
}
description
"The power difference in dB, when it is known or an empty
value when the difference is not known.";
}
typedef power-dbm {
type decimal-2;
units "dBm";
description
"The power in dBm.";
}
typedef power-dbm-or-null {
type union {
type power-dbm;
type empty;
}
description
"The power in dBm, when it is known or an empty value when the
power is not known.";
}
Belotti, et al. Expires 19 December 2025 [Page 28]
Internet-Draft L0 Common YANG Types June 2025
typedef decimal-5 {
type decimal64 {
fraction-digits 5;
}
description
"A decimal64 value with five digits.";
}
typedef decimal-5-or-null {
type union {
type decimal-5;
type empty;
}
description
"A decimal64 value with five digits, when the value is known
or an empty value when the value is not known.";
}
typedef psd {
type decimal64 {
fraction-digits 16;
}
units "W/Hz";
description
"The power spectral density (PSD).
Typical value : 3.9 E-14, resolution 0.1nW/MHz.";
reference
"ITU-T G.9700 (07/2019): Fast access to subscriber terminals
(G.fast) - Power spectral density specification";
}
typedef psd-or-null {
type union {
type psd;
type empty;
}
description
"The power spectral density (PSD), when it is known or an
empty value when the PSD is not known.";
}
typedef decimal-18 {
type decimal64 {
fraction-digits 18;
}
description
"A decimal64 value with eighteen digits.";
Belotti, et al. Expires 19 December 2025 [Page 29]
Internet-Draft L0 Common YANG Types June 2025
}
typedef decimal-18-or-null {
type union {
type decimal-18;
type empty;
}
description
"A decimal64 value with eighteen digits, when the value is
known or an empty value when the value is not known.";
}
/*
* Groupings
*/
grouping wdm-label-start-end {
description
"The WDM label-start or label-end used to specify DWDM and
CWDM label range.";
choice grid-type {
description
"Label for fixed & flexi-DWDM or CWDM grid";
case fixed-dwdm {
leaf dwdm-n {
when "derived-from-or-self(../../../grid-type,
\"wson-grid-dwdm\")" {
description
"Valid only when grid type is DWDM.";
}
type dwdm-n;
description
"The given value 'N' is used to determine the
nominal central frequency.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
case cwdm {
leaf cwdm-n {
when "derived-from-or-self(../../../grid-type,
\"wson-grid-cwdm\")" {
description
"Valid only when grid type is CWDM.";
}
type cwdm-n;
Belotti, et al. Expires 19 December 2025 [Page 30]
Internet-Draft L0 Common YANG Types June 2025
description
"The given value 'N' is used to determine the nominal
central wavelength.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
case flexi-grid {
uses flexi-grid-label-start-end;
}
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers";
}
grouping wdm-label-step {
description
"Label step information for fixed & flexi-DWDM or CWDM grid";
choice l0-grid-type {
description
"Grid type: DWDM, CWDM, etc.";
case fixed-dwdm {
leaf wson-dwdm-channel-spacing {
when "derived-from-or-self(../../grid-type,
\"wson-grid-dwdm\")" {
description
"Valid only when grid type is DWDM.";
}
type identityref {
base dwdm-ch-spc-type;
}
description
"Label-step is the channel spacing (GHz), e.g., 100.000,
50.000, 25.000, or 12.500 GHz for DWDM.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
case cwdm {
leaf wson-cwdm-channel-spacing {
when "derived-from-or-self(../../grid-type,
\"wson-grid-cwdm\")" {
description
"Valid only when grid type is CWDM.";
}
Belotti, et al. Expires 19 December 2025 [Page 31]
Internet-Draft L0 Common YANG Types June 2025
type identityref {
base cwdm-ch-spc-type;
}
description
"Label-step is the channel spacing (nm), i.e., 20 nm
for CWDM, which is the only value defined for CWDM.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
case flexi-grid {
uses flexi-grid-label-step;
}
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
CWDM wavelength grid,
RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
Dense Wavelength Division Multiplexing (DWDM) Networks";
}
grouping wdm-label-hop {
description
"Generic label-hop information for fixed & flexi-DWDM or
CWDM grid";
choice grid-type {
description
"Label for DWDM or CWDM grid";
case fixed-dwdm {
choice fixed-single-or-super-channel {
description
"single or super channel";
case single {
leaf dwdm-n {
type dwdm-n;
description
"The given value 'N' is used to determine the
nominal central frequency.";
}
}
case multi {
leaf-list subcarrier-dwdm-n {
type dwdm-n;
min-elements 2;
description
Belotti, et al. Expires 19 December 2025 [Page 32]
Internet-Draft L0 Common YANG Types June 2025
"The given values 'N' are used to determine the
nominal central frequency for each subcarrier
channel.";
reference
"ITU-T G.694.1 (10/2020): Spectral grids for WDM
applications: DWDM frequency grid";
}
}
}
}
case cwdm {
leaf cwdm-n {
type cwdm-n;
description
"The given value 'N' is used to determine the nominal
central wavelength.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
case flexi-grid {
uses flexi-grid-label-hop;
}
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers";
}
grouping wdm-label-range-info {
description
"WDM label range related information";
uses l0-label-range-info;
container flexi-grid {
when "derived-from-or-self(../grid-type,
\"flexi-grid-dwdm\")" {
description
"Applicable only when the grid type is flexi-grid-dwdm.";
}
description
"flexi-grid definition";
leaf slot-width-granularity {
type identityref {
base flexi-slot-width-granularity;
}
default "flexi-swg-12p5ghz";
description
Belotti, et al. Expires 19 December 2025 [Page 33]
Internet-Draft L0 Common YANG Types June 2025
"Minimum space between slot widths. Default is 12.500
GHz.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
}
leaf min-slot-width-factor {
type uint16 {
range "1..max";
}
default "1";
description
"A multiplier of the slot width granularity, indicating
the minimum slot width supported by an optical port.
Minimum slot width is calculated by:
Minimum slot width (GHz) =
min-slot-width-factor * slot-width-granularity.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
}
leaf max-slot-width-factor {
type uint16 {
range "1..max";
}
must '. >= ../min-slot-width-factor' {
error-message
"Maximum slot width must be greater than or equal to
minimum slot width.";
}
description
"A multiplier of the slot width granularity, indicating
the maximum slot width supported by an optical port.
Maximum slot width is calculated by:
Maximum slot width (GHz) =
max-slot-width-factor * slot-width-granularity
If specified, maximum slot width must be greater than or
equal to minimum slot width. If not specified, maximum
slot width is equal to minimum slot width.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
Belotti, et al. Expires 19 December 2025 [Page 34]
Internet-Draft L0 Common YANG Types June 2025
}
}
}
grouping wson-label-start-end {
description
"The WSON label-start or label-end used to specify WSON label
range.";
choice grid-type {
description
"Label for DWDM or CWDM grid";
case dwdm {
leaf dwdm-n {
when "derived-from-or-self(../../../grid-type,
\"wson-grid-dwdm\")" {
description
"Valid only when grid type is DWDM.";
}
type dwdm-n;
description
"The central frequency of DWDM.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
case cwdm {
leaf cwdm-n {
when "derived-from-or-self(../../../grid-type,
\"wson-grid-cwdm\")" {
description
"Valid only when grid type is CWDM.";
}
type cwdm-n;
description
"Channel wavelength computing input.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers";
}
grouping wson-label-hop {
Belotti, et al. Expires 19 December 2025 [Page 35]
Internet-Draft L0 Common YANG Types June 2025
description
"Generic label-hop information for WSON";
choice grid-type {
description
"Label for DWDM or CWDM grid";
case dwdm {
choice single-or-super-channel {
description
"single or super channel";
case single {
leaf dwdm-n {
type dwdm-n;
description
"The given value 'N' is used to determine the
nominal central frequency.";
}
}
case super {
leaf-list subcarrier-dwdm-n {
type dwdm-n;
description
"The given values 'N' are used to determine the
nominal central frequency for each subcarrier
channel.";
reference
"ITU-T G.694.1 (10/2020): Spectral grids for WDM
applications: DWDM frequency grid";
}
}
}
}
case cwdm {
leaf cwdm-n {
type cwdm-n;
description
"The given value 'N' is used to determine the nominal
central wavelength.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers";
}
Belotti, et al. Expires 19 December 2025 [Page 36]
Internet-Draft L0 Common YANG Types June 2025
grouping l0-label-range-info {
description
"Information about Layer 0 label range.";
leaf grid-type {
type identityref {
base l0-grid-type;
}
description
"Grid type";
}
leaf priority {
type uint8;
description
"Priority in Interface Switching Capability Descriptor
(ISCD).";
reference
"RFC 4203: OSPF Extensions in Support of Generalized
Multi-Protocol Label Switching (GMPLS)";
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers";
}
grouping wson-label-step {
description
"Label step information for WSON";
choice l0-grid-type {
description
"Grid type: DWDM, CWDM, etc.";
case dwdm {
leaf wson-dwdm-channel-spacing {
when "derived-from-or-self(../../grid-type,
\"wson-grid-dwdm\")" {
description
"Valid only when grid type is DWDM.";
}
type identityref {
base dwdm-ch-spc-type;
}
description
"Label-step is the channel spacing (GHz), e.g., 100.000,
50.000, 25.000, or 12.500 GHz for DWDM.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
Belotti, et al. Expires 19 December 2025 [Page 37]
Internet-Draft L0 Common YANG Types June 2025
case cwdm {
leaf wson-cwdm-channel-spacing {
when "derived-from-or-self(../../grid-type,
\"wson-grid-cwdm\")" {
description
"Valid only when grid type is CWDM.";
}
type identityref {
base cwdm-ch-spc-type;
}
description
"Label-step is the channel spacing (nm), i.e., 20 nm
for CWDM, which is the only value defined for CWDM.";
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable
(LSC) Label Switching Routers";
}
}
}
reference
"RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
Label Switching Routers,
ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
CWDM wavelength grid";
}
grouping flexi-grid-label-start-end {
description
"The flexi-grid label-start or label-end used to specify
flexi-grid label range.";
leaf flexi-n {
type flexi-n;
description
"The given value 'N' is used to determine the nominal
central frequency.
As described in section 3.1 of RFC 8363, the range of
available nominal central frequencies are advertised for
m=1, which means that for an available central frequency n,
the frequency slot from central frequency n-1 to central
frequency n+1 is available.";
}
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers,
RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
Belotti, et al. Expires 19 December 2025 [Page 38]
Internet-Draft L0 Common YANG Types June 2025
Dense Wavelength Division Multiplexing (DWDM) Networks";
}
grouping flexi-grid-frequency-slot {
description
"Flexi-grid frequency slot grouping.";
uses flexi-grid-label-start-end;
leaf flexi-m {
type flexi-m;
description
"The given value 'M' is used to determine the slot width.";
}
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers";
}
grouping flexi-grid-label-hop {
description
"Generic label-hop information for flexi-grid";
choice single-or-super-channel {
description
"single or super channel";
case single {
uses flexi-grid-frequency-slot;
}
case super {
status deprecated;
list subcarrier-flexi-n {
key "flexi-n";
status deprecated;
uses flexi-grid-frequency-slot {
status deprecated;
}
description
"List of subcarrier channels for flexi-grid super
channel.";
}
}
case multi {
container frequency-slots {
description
"The top level container for the list of frequency
slots used for flexi-grid super channel.";
list frequency-slot {
key "flexi-n";
min-elements 2;
uses flexi-grid-frequency-slot;
Belotti, et al. Expires 19 December 2025 [Page 39]
Internet-Draft L0 Common YANG Types June 2025
description
"List of frequency slots used for flexi-grid super
channel.";
}
}
}
}
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
Dense Wavelength Division Multiplexing (DWDM) Networks";
}
grouping flexi-grid-label-range-info {
description
"Flexi-grid-specific label range related information";
uses l0-label-range-info;
container flexi-grid {
description
"flexi-grid definition";
leaf slot-width-granularity {
type identityref {
base flexi-slot-width-granularity;
}
default "flexi-swg-12p5ghz";
description
"Minimum space between slot widths. Default is 12.500
GHz.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of
Flexi-Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
}
leaf min-slot-width-factor {
type uint16 {
range "1..max";
}
default "1";
description
"A multiplier of the slot width granularity, indicating
the minimum slot width supported by an optical port.
Minimum slot width is calculated by:
Minimum slot width (GHz) =
min-slot-width-factor * slot-width-granularity.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
Belotti, et al. Expires 19 December 2025 [Page 40]
Internet-Draft L0 Common YANG Types June 2025
}
leaf max-slot-width-factor {
type uint16 {
range "1..max";
}
must '. >= ../min-slot-width-factor' {
error-message
"Maximum slot width must be greater than or equal to
minimum slot width.";
}
description
"A multiplier of the slot width granularity, indicating
the maximum slot width supported by an optical port.
Maximum slot width is calculated by:
Maximum slot width (GHz) =
max-slot-width-factor * slot-width-granularity
If specified, maximum slot width must be greater than or
equal to minimum slot width. If not specified, maximum
slot width is equal to minimum slot width.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
Grid Dense Wavelength Division Multiplexing (DWDM)
Networks";
}
}
}
grouping flexi-grid-label-step {
description
"Label step information for flexi-grid";
leaf flexi-grid-channel-spacing {
type identityref {
base flexi-ch-spc-type;
}
default "flexi-ch-spc-6p25ghz";
status deprecated;
description
"Label-step is the nominal central frequency granularity
(GHz), e.g., 6.25 GHz.";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers";
}
leaf flexi-ncfg {
type identityref {
base flexi-ncfg-type;
Belotti, et al. Expires 19 December 2025 [Page 41]
Internet-Draft L0 Common YANG Types June 2025
}
default "flexi-ncfg-6p25ghz";
description
"Label-step is the nominal central frequency granularity
(GHz), e.g., 6.25 GHz.";
reference
"RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
Switch Capable (LSC) Label Switching Routers";
}
leaf flexi-n-step {
type uint8;
description
"This attribute defines the multiplier for the supported
values of 'N'.
For example, given a grid with a nominal central frequency
granularity of 6.25 GHz, the granularity of the supported
values of the nominal central frequency could be 12.5 GHz.
In this case, the values of flexi-n should be even and this
constraint is reported by setting the flexi-n-step to 2.
This attribute is also known as central frequency
granularity in RFC 8363.";
reference
"RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
Dense Wavelength Division Multiplexing (DWDM) Networks";
}
}
grouping transceiver-capabilities {
description
"This grouping is intended to be used for reporting the
capabilities of a transceiver.
When this grouping is used, the explicit-mode container shall
be augmented with a leafref to an explicit mode template with
the proper XPath which depends from where this grouping is
actually used.
See for example the ietf-optical-impairment-topology YANG
module in RFC YYYY.";
reference
"RFC YYYY: A YANG Data Model for Optical Impairment-aware
Topology.";
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
container supported-modes {
Belotti, et al. Expires 19 December 2025 [Page 42]
Internet-Draft L0 Common YANG Types June 2025
presence
"When present, it indicates that the modes supported by a
transceiver are reported.";
config false;
description
"The top level container for the list supported
transceiver's modes.";
list supported-mode {
key "mode-id";
config false;
min-elements 1;
description "The list of supported transceiver's modes.";
leaf mode-id {
type string {
length "1..255";
}
description "ID for the supported transceiver's mode.";
}
choice mode {
config false;
mandatory true;
description
"Indicates whether the transceiver's mode is a standard
mode, an organizational mode or an explicit mode.";
case G.698.2 {
uses standard-mode;
uses common-standard-organizational-mode;
uses common-all-modes;
}
case organizational-mode {
container organizational-mode {
config false;
description
"The set of attributes for an organizational mode";
uses organizational-mode;
uses common-standard-organizational-mode;
uses common-all-modes;
} // container organizational-mode
}
case explicit-mode {
container explicit-mode {
config false;
description
"The set of attributes for an explicit mode.";
uses common-all-modes;
container compatible-modes {
description
"Container for all the standard and organizational
Belotti, et al. Expires 19 December 2025 [Page 43]
Internet-Draft L0 Common YANG Types June 2025
modes supported by the transceiver's explicit
mode.";
leaf-list supported-application-code {
type leafref {
path "../../../../supported-mode/mode-id";
}
must "../../../../"
+ "supported-mode[mode-id=current()]/"
+ "standard-mode" {
description
"The pointer is only for application codes
supported by transceiver.";
}
description
"List of pointers to the application codes
supported by the transceiver's explicit mode.";
}
leaf-list supported-organizational-mode {
type leafref {
path "../../../../supported-mode/mode-id";
}
must "../../../../"
+ "supported-mode[mode-id=current()]/"
+ "organizational-mode" {
description
"The pointer is only for organizational modes
supported by transceiver.";
}
description
"List of pointers to the organizational modes
supported by the transceiver's explicit mode.";
}
} // container compatible-modes
} // container explicit-mode
} // end of case explicit-mode
} // end of choice
} // list supported-mode
} // container supported-modes
} // grouping transceiver-capabilities
grouping standard-mode {
description
"ITU-T G.698.2 standard mode that guarantees interoperability.
It must be an string with the following format:
B-DScW-ytz(v) where all these attributes are conformant
to the ITU-T recomendation";
leaf standard-mode {
Belotti, et al. Expires 19 December 2025 [Page 44]
Internet-Draft L0 Common YANG Types June 2025
type standard-mode;
config false;
description
"G.698.2 standard mode";
}
}
grouping organizational-mode {
description
"Transponder operational mode supported by organizations or
vendor";
leaf operational-mode {
type operational-mode;
config false;
description
"configured organization- or vendor-specific
application identifiers (AI) supported by the transponder";
}
leaf organization-identifier {
type organization-identifier;
config false;
description
"organization identifier that uses organizational
mode";
}
}
grouping penalty-value {
description
"A common definition of the OSNR penalty value used for
describing multiple penalty types (.e.g, CD, PMD, PDL).";
leaf penalty-value {
type union {
type decimal-2 {
range "0..max";
}
type empty;
}
units "dB";
config false;
mandatory true;
description
"The OSNR penalty associated with the related optical
impairment at the receiver, when the value is known or an
empty value when the value is not known.";
}
Belotti, et al. Expires 19 December 2025 [Page 45]
Internet-Draft L0 Common YANG Types June 2025
}
grouping explicit-mode {
description
"Attributes capabilities related to explicit transceiver's
mode.
This grouping also contains the list of attributes related to
optical impairment limits for explicit mode (min OSNR, max PMD,
max CD, max PDL, Q-factor limit, etc.).
In case of standard and operational mode the attributes are
implicit.";
leaf line-coding-bitrate {
type identityref {
base line-coding;
}
config false;
description
"Bit rate/line coding of the optical tributary signal.";
reference
"ITU-T G.698.2 section 7.1.2";
}
leaf bitrate {
type uint16;
units "Gbit/sec";
config false;
description
"The gross bitrate (e.g., 100, 200) of the optical tributary
signal.";
}
leaf max-diff-group-delay {
type decimal-2;
units "ps";
config false;
description
"Maximum Differential group delay of this mode for this
lane";
}
leaf max-chromatic-dispersion {
type decimal-2 {
range "0..max";
}
units "ps/nm";
config false;
description
"Maximum acceptable accumulated chromatic dispersion (CD)
on the receiver at Rx-power reference point
Belotti, et al. Expires 19 December 2025 [Page 46]
Internet-Draft L0 Common YANG Types June 2025
(rx-ref-channel-power) and in absence of other impairments";
reference
"Section 2.6.4 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
list cd-penalty {
key cd-value;
config false;
description
"Optional penalty associated with a given accumulated
chromatic dispersion (CD) value measured in
absence of other impairments.
This list of pair CD and OSNR penalty can be used to
sample the function OSNR penalty = f(CD).";
leaf cd-value {
type decimal-2;
units "ps/nm";
config false;
mandatory true;
description
"The Chromatic Dispersion (CD).";
}
uses penalty-value;
reference
"Section 2.6.4 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
leaf max-polarization-mode-dispersion {
type decimal-2 {
range "0..max";
}
units "ps";
config false;
description
"Maximum acceptable accumulated polarization mode
dispersion (PMD) on the receiver at Rx-power reference point
(rx-ref-channel-power) and in absence of other impairments";
reference
"ITU-T G.666 (02/2011): Characteristics of polarization
mode dispersion compensators and of receivers that
compensate for polarization mode dispersion
Belotti, et al. Expires 19 December 2025 [Page 47]
Internet-Draft L0 Common YANG Types June 2025
Section 2.6.4 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
list pmd-penalty {
key pmd-value;
config false;
description
"Optional penalty associated with a given accumulated
polarization mode dispersion (PMD) value measured in
absence of other impairments.
This list of pair PMD and OSNR penalty can be used to
sample the function OSNR penalty = f(PMD).";
leaf pmd-value {
type decimal-2 {
range "0..max";
}
units "ps";
config false;
mandatory true;
description
"The Polarization Mode Dispersion (PMD).";
}
uses penalty-value;
reference
"Section 2.6.4 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
leaf max-polarization-dependent-loss {
type power-loss-or-null;
config false;
mandatory true;
description
"Maximum acceptable accumulated polarization dependent
loss (PDL) on the receiver at Rx-power reference point
(rx-ref-channel-power) and in absence of other impairments";
reference
"Section 2.6.4 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
Belotti, et al. Expires 19 December 2025 [Page 48]
Internet-Draft L0 Common YANG Types June 2025
// is published as an RFC
list pdl-penalty {
key pdl-value;
config false;
description
"Optional penalty associated with a given accumulated
polarization dependent loss (PDL) value, measured in
absence of other impairments.
This list of pair PDL and OSNR penalty can be used to
sample the function OSNR penalty = f(PDL).";
leaf pdl-value {
type power-loss;
config false;
mandatory true;
description
"Maximum acceptable accumulated polarization dependent
loss (PDL).";
}
uses penalty-value;
reference
"Section 2.6.4 of RFC YYYY: A YANG Data Model for Optical
Impairment-aware Topology.";
}
// RFC Ed.: replace YYYY with actual RFC number and remove
// this note after draft-ietf-ccamp-optical-impairment-topology-yang
// is published as an RFC
leaf available-modulation-type {
type identityref {
base modulation;
}
config false;
description
"Modulation type the specific transceiver in the list
can support";
}
leaf min-OSNR {
type snr;
units "dBm";
config false;
description
"min OSNR measured over 0.1 nm resolution bandwidth:
if received OSNR at Rx-power reference point
(rx-ref-channel-power) is lower than MIN-OSNR, an increased
level of bit-errors post-FEC needs to be expected";
}
leaf rx-ref-channel-power {
type power-dbm;
Belotti, et al. Expires 19 December 2025 [Page 49]
Internet-Draft L0 Common YANG Types June 2025
config false;
description
"The channel power used as reference for defining penalties
and min-OSNR";
}
list rx-channel-power-penalty {
key rx-channel-power-value;
config false;
description
"Optional penalty associated with a received power
lower than rx-ref-channel-power.
This list of pair power and OSNR penalty can be used to
sample the function OSNR penalty = f(rx-channel-power).";
leaf rx-channel-power-value {
type power-dbm;
units "dBm";
config false;
mandatory true;
description
"The Received Power.";
}
uses penalty-value;
}
leaf min-Q-factor {
type decimal-2;
units "dB";
config false;
description "min Qfactor at FEC threshold";
}
leaf available-baud-rate {
type decimal64 {
fraction-digits 1;
}
units "Bd";
config false;
description
"Baud-rate the specific transceiver in
the list can support.
Baud-rate is the unit for
symbol rate or modulation rate
in symbols per second or
pulses per second.
It is the number of distinct symbol
changes (signal events) made to the
transmission medium
per second in a digitally
modulated signal or a line code";
Belotti, et al. Expires 19 December 2025 [Page 50]
Internet-Draft L0 Common YANG Types June 2025
}
leaf roll-off {
type decimal64 {
fraction-digits 4;
range "0..1";
}
config false;
description
"the roll-off factor (beta with values from 0 to 1)
identifies how the real signal shape exceed
the baud rate. If=0 it is exactly matching
the baud rate.If=1 the signal exceeds the
50% of the baud rate at each side.";
}
leaf min-carrier-spacing {
type frequency-ghz;
config false;
description
"This attribute specifies the minimum nominal difference
between the carrier frequencies of two homogeneous OTSis
(which have the same optical characteristics but the central
frequencies) such that if they are placed next to each other
the interference due to spectrum overlap between them can be
considered negligible.
In case of heterogeneous OTSi it is up to path computation
engine to determine the minimum distance between the carrier
frequency of the two adjacent OTSi.";
}
leaf available-fec-type {
type identityref {
base fec-type;
}
config false;
description "Available FEC";
}
leaf fec-code-rate {
type decimal64 {
fraction-digits 8;
range "0..max";
}
config false;
description "FEC-code-rate";
}
leaf fec-threshold {
type decimal64 {
fraction-digits 8;
range "0..max";
Belotti, et al. Expires 19 December 2025 [Page 51]
Internet-Draft L0 Common YANG Types June 2025
}
config false;
description
"Threshold on the BER, for which FEC
is able to correct errors";
}
leaf in-band-osnr {
type snr;
config false;
description
"The OSNR defined within the bandwidth of the transmit
spectral excursion (i.e., between the nominal central
frequency of the channel and the -3.0dB points of the
transmitter spectrum furthest from the nominal central
frequency) measured at reference point Ss.
The in-band OSNR is referenced to an optical bandwidth of
0.1nm @ 193.7 THz or 12.5 GHz.";
reference
"OIF-400ZR-01.0: Implementation Agreement 400ZR";
}
leaf out-of-band-osnr {
type snr;
config false;
description
"The ratio of the peak transmitter power to the integrated
power outside the transmitter spectral excursion.
The spectral resolution of the measurement shall be better
than the maximum spectral width of the peak.
The out-of-band OSNR is referenced to an optical bandwidth
of 0.1nm @ 193.7 THz or 12.5 GHz";
reference
"OIF-400ZR-01.0: Implementation Agreement 400ZR";
}
leaf tx-polarization-power-difference {
type power-ratio;
config false;
description
"The transmitter polarization dependent power difference
defined as the power difference between X and Y
polarizations";
reference
"OIF-400ZR-01.0: Implementation Agreement 400ZR";
}
leaf polarization-skew {
type decimal-2;
Belotti, et al. Expires 19 December 2025 [Page 52]
Internet-Draft L0 Common YANG Types June 2025
units "ps";
config false;
description
"The X-Y skew, included as a fixed value in the receiver
polarization mode dispersion (PMD) tolerance limits.";
reference
"OIF-400ZR-01.0: Implementation Agreement 400ZR";
}
} // grouping explicit-mode
grouping common-standard-organizational-mode {
description
"Common attributes used by standard and organizational
transceiver's modes.";
leaf-list line-coding-bitrate {
type identityref {
base line-coding;
}
config false;
description
"The list of the bit rate/line coding of the optical
tributary signal supported by the transceiver.
Reporting this list is optional when the standard or
organization mode supports only one bit rate/line coding.";
reference
"ITU-T G.698.2 section 7.1.2";
}
} // grouping common-standard-organizational-mode
grouping transceiver-tuning-range {
description
"Transceiver tuning range (f-min, f-max, f-granularity)";
leaf min-central-frequency {
type frequency-thz;
description
"This parameter indicates the minimum frequency for the
transceiver tuning range.";
}
leaf max-central-frequency {
type frequency-thz;
description
"This parameter indicates the maximum frequency for the
transceiver tuning range.";
}
Belotti, et al. Expires 19 December 2025 [Page 53]
Internet-Draft L0 Common YANG Types June 2025
leaf transceiver-tunability-granularity {
type frequency-ghz;
description
"This parameter indicates the transceiver frequency fine
tuning granularity e.g 3.125GHz or 0.001GHz.";
}
} // grouping transceiver-tuning-range
grouping common-all-modes {
description
"Common attributes used by all transceiver's modes.";
container transceiver-tuning-range {
config false;
description
"Transceiver tuning range (f-min, f-max, f-granularity)";
uses transceiver-tuning-range;
}
leaf tx-channel-power-min {
type power-dbm;
config false;
description "The minimum output power of this interface";
}
leaf tx-channel-power-max {
type power-dbm;
config false;
description "The maximum output power of this interface";
}
leaf rx-channel-power-min {
type power-dbm;
config false;
description "The minimum input power of this interface";
}
leaf rx-channel-power-max {
type power-dbm;
config false;
description "The maximum input power of this interface";
}
leaf rx-total-power-max {
type power-dbm;
config false;
description
"Maximum rx optical power for all the channels.
It is applicable only to multi-channel modes.";
}
} // grouping common-all-modes
Belotti, et al. Expires 19 December 2025 [Page 54]
Internet-Draft L0 Common YANG Types June 2025
grouping common-transceiver-param {
description
"The common parameters of an optical transceiver,
that supplement the configured mode.";
uses common-transceiver-configured-param;
uses common-transceiver-readonly-param;
}
grouping common-transceiver-configured-param {
description
"The configured parameters of an optical transceiver,
that supplement the configured mode.";
leaf line-coding-bitrate {
type identityref {
base line-coding;
}
description
"Bit rate/line coding of the optical tributary signal.
Support of this attribute is optional when the configured
mode supports only one bit rate/line coding.";
reference
"ITU-T G.698.2 section 7.1.2";
}
leaf tx-channel-power {
type power-dbm-or-null;
description
"The current channel transmit power, when the value is
known or an empty value when the value is not known.
The empty value MUST NOT be used when this attribute is
configured.";
}
} // grouping for configured transceiver attributes out of mode
grouping common-transceiver-readonly-param {
description
"The common read-only parameters of an optical transceiver,
that supplement the configured mode.";
leaf rx-channel-power {
type power-dbm-or-null;
config false;
description
"The current channel received power, when the value is
known or an empty value when the value is not known.";
Belotti, et al. Expires 19 December 2025 [Page 55]
Internet-Draft L0 Common YANG Types June 2025
}
leaf rx-total-power {
type power-dbm-or-null;
config false;
description
"The current total received power, when the value is known
or an empty value when the value is not known.";
}
} // grouping for read-only transceiver attributes out of mode
grouping tunnel-attributes {
description
"Parameters for Layer0 (WSON or Flexi-Grid) Tunnels.";
leaf wavelength-assignment {
type identityref {
base wavelength-assignment;
}
description "Wavelength Allocation Method";
}
}
grouping frequency-range {
description
"This grouping defines the lower and upper bounds of a
frequency range (e.g., a band).
This grouping SHOULD NOT be used to define a frequency slot,
which SHOULD be defined using the n and m values instead.";
leaf lower-frequency {
type frequency-thz;
mandatory true;
description
"The lower frequency boundary of the
frequency range.";
}
leaf upper-frequency {
type frequency-thz;
must '. > ../lower-frequency' {
error-message
"The upper frequency must be greater than the lower
frequency.";
}
mandatory true;
description
"The upper frequency boundary of the
frequency range.";
}
Belotti, et al. Expires 19 December 2025 [Page 56]
Internet-Draft L0 Common YANG Types June 2025
}
grouping frequency-range-with-identifier {
description
"This grouping extends the frequency-range defined in
ietf-layer0-types with an identifier, which used as a key when
it is needed to define different properties (e.g., optical
impairments) for different frequency ranges.";
leaf frequency-range-id {
type uint16;
description
"The identifier of the frequency range.";
}
container frequency-range {
description
"The frequency range for which these optical
impairments apply.";
uses frequency-range;
}
}
grouping path-constraints {
description
"Common attribute for Layer 0 path constraints to be used by
Layer 0 computation.";
leaf gsnr-extra-margin {
type snr {
range 0..max;
}
default 0;
description
"An additional margin to be added to the OSNR-min of the
transceiver when checking the estimated received Generalized
SNR (GSNR).";
}
}
grouping path-properties {
description
"Common attribute for reporting the Layer 0 computed path
properties.";
leaf estimated-gsnr {
type snr;
config false;
description
"The estimate received GSNR for the computed path.";
}
leaf estimated-eol-gsnr {
Belotti, et al. Expires 19 December 2025 [Page 57]
Internet-Draft L0 Common YANG Types June 2025
type snr;
config false;
description
"The estimate received GSNR for the computed path
degraded at the end of life.";
}
leaf estimated-lowest-gsnr {
type snr;
config false;
description
"The estimate lowest received GSNR for the computed path
among all possible wavelength channels along the same
path.";
}
}
}
<CODE ENDS>
Figure 1: Layer 0 Types YANG module
4. Security Considerations
This section is modeled after the template described in Section 3.7
of [I-D.ietf-netmod-rfc8407bis].
The "ietf-layer0-types" YANG module defines a data model that is
designed to be accessed via YANG-based management protocols, such as
NETCONF [RFC6241] and RESTCONF [RFC8040]. These YANG-based
management protocols (1) have to use a secure transport layer (e.g.,
SSH [RFC4252], TLS [RFC8446], and QUIC [RFC9000]) and (2) have to use
mutual authentication.
The Network Configuration Access Control Model (NACM) [RFC8341]
provides the means to restrict access for particular NETCONF or
RESTCONF users to a preconfigured subset of all available NETCONF or
RESTCONF protocol operations and content.
The YANG module defines a set of identities, types, and groupings.
These nodes are intended to be reused by other YANG modules. The
module by itself does not expose any data nodes that are writable,
data nodes that contain read-only state, or RPCs. As such, there are
no additional security issues related to the YANG module that need to
be considered.
Modules that use the groupings that are defined in this document
should identify the corresponding security considerations.
Belotti, et al. Expires 19 December 2025 [Page 58]
Internet-Draft L0 Common YANG Types June 2025
5. IANA Considerations
IANA is requested to update the following registration in the "ns"
registry within the "IETF XML Registry" group [RFC3688] to reference
this document:
URI: urn:ietf:params:xml:ns:yang:ietf-layer0-types
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
IANA is requested to register the following YANG module in the "YANG
Module Names" registry [RFC6020] within the "YANG Parameters"
registry group.
Name: ietf-layer0-types
Maintained by IANA? N
Namespace: urn:ietf:params:xml:ns:yang:ietf-layer0-types
Prefix: l0-types
Reference: RFC XXXX
RFC Editor Note: Please replace XXXX with the RFC number assigned
to this document and remove this note.
6. References
6.1. Normative References
[I-D.ietf-ccamp-optical-impairment-topology-yang]
Beller, D., Le Rouzic, E., Belotti, S., Galimberti, G.,
and I. Busi, "A YANG Data Model for Optical Impairment-
aware Topology", Work in Progress, Internet-Draft, draft-
ietf-ccamp-optical-impairment-topology-yang-18, 11 April
2025, <https://datatracker.ietf.org/doc/html/draft-ietf-
ccamp-optical-impairment-topology-yang-18>.
[I-D.ietf-teas-rfc8776-update]
Busi, I., Guo, A., Liu, X., Saad, T., and I. Bryskin,
"Common YANG Data Types for Traffic Engineering", Work in
Progress, Internet-Draft, draft-ietf-teas-rfc8776-update-
17, 21 February 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-teas-
rfc8776-update-17>.
Belotti, et al. Expires 19 December 2025 [Page 59]
Internet-Draft L0 Common YANG Types June 2025
[ITU-T_G.666]
International Telecommunication Union, "Characteristics of
polarization mode dispersion compensators and of receivers
that compensate for polarization mode dispersion"", ITU-T
Recommendation G.666 , February 2011,
<https://www.itu.int/rec/T-REC-G.666>.
[ITU-T_G.694.1]
International Telecommunication Union, "Spectral grids for
WDM applications: DWDM frequency grid", ITU-T
Recommendation G.694.1 , October 2020,
<https://www.itu.int/rec/T-REC-G.694.1>.
[ITU-T_G.694.2]
International Telecommunication Union, "Spectral grids for
WDM applications: CWDM wavelength grid", ITU-T
Recommendation G.694.2 , December 2003,
<https://www.itu.int/rec/T-REC-G.694.2>.
[ITU-T_G.698.2]
International Telecommunication Union, "Amplified
multichannel dense wavelength division multiplexing
applications with single channel optical interfaces",
ITU-T Recommendation G.698.2 , November 2018,
<https://www.itu.int/rec/T-REC-G.698.2>.
[ITU-T_G.709]
International Telecommunication Union, "Interfaces for the
optical transport network", ITU-T Recommendation G.709 ,
June 2020, <https://www.itu.int/rec/T-REC-G.709>.
[ITU-T_G.709.2]
International Telecommunication Union, "OTU4 long-reach
interface", ITU-T Recommendation G.709.2, Corrigendum 1 ,
September 2020, <https://www.itu.int/rec/T-REC-G.709.2>.
[ITU-T_G.709.3]
International Telecommunication Union, "Flexible OTN B100G
long-reach interfaces", ITU-T Recommendation G.709.3,
Amendment 1 , November 2022,
<https://www.itu.int/rec/T-REC-G.709.3>.
[ITU-T_G.959.1]
International Telecommunication Union, "Optical transport
network physical layer interfaces", ITU-T Recommendation
G.959.1 , July 2018,
<https://www.itu.int/rec/T-REC-G.959.1>.
Belotti, et al. Expires 19 December 2025 [Page 60]
Internet-Draft L0 Common YANG Types June 2025
[ITU-T_G.9700]
International Telecommunication Union, "Fast access to
subscriber terminals (G.fast) - Power spectral density
specification", ITU-T Recommendation G.9700 , July 2019,
<https://www.itu.int/rec/T-REC-G.9700>.
[ITU-T_G.975]
International Telecommunication Union, "Forward error
correction for submarine systems", ITU-T Recommendation
G.975 , October 2000,
<https://www.itu.int/rec/T-REC-G.975>.
[ITU-T_G.975.1]
International Telecommunication Union, "Forward error
correction for high bit-rate DWDM submarine systems",
ITU-T Recommendation G.975.1, Corrigendum 2 , July 2013,
<https://www.itu.int/rec/T-REC-G.975.1>.
[ITU-T_G.977.1]
International Telecommunication Union, "Transverse
compatible dense wavelength division multiplexing
applications for repeatered optical fibre submarine cable
systems", ITU-T Recommendation G.977.1 , February 2021,
<https://www.itu.int/rec/T-REC-G.977.1>.
[OIF_400ZR]
Optical Internetworking Forum, "Implementation Agreement
400ZR", OIF-400ZR-01.0 Implementation Agreement , March
2020, <https://www.oiforum.com/wp-content/uploads/OIF-
400ZR-01.0_reduced2.pdf>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/rfc/rfc2119>.
[RFC3471] Berger, L., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Functional Description",
RFC 3471, DOI 10.17487/RFC3471, January 2003,
<https://www.rfc-editor.org/rfc/rfc3471>.
[RFC4203] Kompella, K., Ed. and Y. Rekhter, Ed., "OSPF Extensions in
Support of Generalized Multi-Protocol Label Switching
(GMPLS)", RFC 4203, DOI 10.17487/RFC4203, October 2005,
<https://www.rfc-editor.org/rfc/rfc4203>.
Belotti, et al. Expires 19 December 2025 [Page 61]
Internet-Draft L0 Common YANG Types June 2025
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<https://www.rfc-editor.org/rfc/rfc6020>.
[RFC6205] Otani, T., Ed. and D. Li, Ed., "Generalized Labels for
Lambda-Switch-Capable (LSC) Label Switching Routers",
RFC 6205, DOI 10.17487/RFC6205, March 2011,
<https://www.rfc-editor.org/rfc/rfc6205>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/rfc/rfc6241>.
[RFC7688] Lee, Y., Ed. and G. Bernstein, Ed., "GMPLS OSPF
Enhancement for Signal and Network Element Compatibility
for Wavelength Switched Optical Networks", RFC 7688,
DOI 10.17487/RFC7688, November 2015,
<https://www.rfc-editor.org/rfc/rfc7688>.
[RFC7689] Bernstein, G., Ed., Xu, S., Lee, Y., Ed., Martinelli, G.,
and H. Harai, "Signaling Extensions for Wavelength
Switched Optical Networks", RFC 7689,
DOI 10.17487/RFC7689, November 2015,
<https://www.rfc-editor.org/rfc/rfc7689>.
[RFC7699] Farrel, A., King, D., Li, Y., and F. Zhang, "Generalized
Labels for the Flexi-Grid in Lambda Switch Capable (LSC)
Label Switching Routers", RFC 7699, DOI 10.17487/RFC7699,
November 2015, <https://www.rfc-editor.org/rfc/rfc7699>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/rfc/rfc7950>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.
[RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC8341, March 2018,
<https://www.rfc-editor.org/rfc/rfc8341>.
Belotti, et al. Expires 19 December 2025 [Page 62]
Internet-Draft L0 Common YANG Types June 2025
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/rfc/rfc8342>.
[RFC8363] Zhang, X., Zheng, H., Casellas, R., Gonzalez de Dios, O.,
and D. Ceccarelli, "GMPLS OSPF-TE Extensions in Support of
Flexi-Grid Dense Wavelength Division Multiplexing (DWDM)
Networks", RFC 8363, DOI 10.17487/RFC8363, May 2018,
<https://www.rfc-editor.org/rfc/rfc8363>.
[RFC8795] Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H., and
O. Gonzalez de Dios, "YANG Data Model for Traffic
Engineering (TE) Topologies", RFC 8795,
DOI 10.17487/RFC8795, August 2020,
<https://www.rfc-editor.org/rfc/rfc8795>.
[RFC9093] Zheng, H., Lee, Y., Guo, A., Lopez, V., and D. King, "A
YANG Data Model for Layer 0 Types", RFC 9093,
DOI 10.17487/RFC9093, August 2021,
<https://www.rfc-editor.org/rfc/rfc9093>.
6.2. Informative References
[I-D.ietf-ccamp-dwdm-if-param-yang]
Galimberti, G., Hiremagalur, D., Grammel, G., Manzotti,
R., and D. Breuer, "A YANG data model to manage
configurable DWDM optical interfaces", Work in Progress,
Internet-Draft, draft-ietf-ccamp-dwdm-if-param-yang-12, 12
February 2025, <https://datatracker.ietf.org/doc/html/
draft-ietf-ccamp-dwdm-if-param-yang-12>.
[I-D.ietf-netmod-rfc8407bis]
Bierman, A., Boucadair, M., and Q. Wu, "Guidelines for
Authors and Reviewers of Documents Containing YANG Data
Models", Work in Progress, Internet-Draft, draft-ietf-
netmod-rfc8407bis-28, 5 June 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-netmod-
rfc8407bis-28>.
[ITU-T_G.807]
International Telecommunication Union, "Generic functional
architecture of the optical media network", ITU-T
Supplement G.807, Amendment 1 , January 2021.
Belotti, et al. Expires 19 December 2025 [Page 63]
Internet-Draft L0 Common YANG Types June 2025
[ITU-T_G.872]
International Telecommunication Union, "Architecture of
optical transport networks", ITU-T Supplement G.872,
Amendment 1 , January 2021.
[ITU-T_G.Sup39]
International Telecommunication Union, "Optical system
design and engineering considerations", ITU-T Supplement
G.Sup39 , February 2016.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/rfc/rfc3688>.
[RFC4252] Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH)
Authentication Protocol", RFC 4252, DOI 10.17487/RFC4252,
January 2006, <https://www.rfc-editor.org/rfc/rfc4252>.
[RFC6163] Lee, Y., Ed., Bernstein, G., Ed., and W. Imajuku,
"Framework for GMPLS and Path Computation Element (PCE)
Control of Wavelength Switched Optical Networks (WSONs)",
RFC 6163, DOI 10.17487/RFC6163, April 2011,
<https://www.rfc-editor.org/rfc/rfc6163>.
[RFC7446] Lee, Y., Ed., Bernstein, G., Ed., Li, D., and W. Imajuku,
"Routing and Wavelength Assignment Information Model for
Wavelength Switched Optical Networks", RFC 7446,
DOI 10.17487/RFC7446, February 2015,
<https://www.rfc-editor.org/rfc/rfc7446>.
[RFC7581] Bernstein, G., Ed., Lee, Y., Ed., Li, D., Imajuku, W., and
J. Han, "Routing and Wavelength Assignment Information
Encoding for Wavelength Switched Optical Networks",
RFC 7581, DOI 10.17487/RFC7581, June 2015,
<https://www.rfc-editor.org/rfc/rfc7581>.
[RFC7698] Gonzalez de Dios, O., Ed., Casellas, R., Ed., Zhang, F.,
Fu, X., Ceccarelli, D., and I. Hussain, "Framework and
Requirements for GMPLS-Based Control of Flexi-Grid Dense
Wavelength Division Multiplexing (DWDM) Networks",
RFC 7698, DOI 10.17487/RFC7698, November 2015,
<https://www.rfc-editor.org/rfc/rfc7698>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/rfc/rfc8040>.
Belotti, et al. Expires 19 December 2025 [Page 64]
Internet-Draft L0 Common YANG Types June 2025
[RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
<https://www.rfc-editor.org/rfc/rfc8340>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/rfc/rfc8446>.
[RFC9000] Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
Multiplexed and Secure Transport", RFC 9000,
DOI 10.17487/RFC9000, May 2021,
<https://www.rfc-editor.org/rfc/rfc9000>.
Appendix A. The Complete Schema Trees
This appendix presents the complete tree of the Layer 0 Types data
model. See [RFC8340] for an explanation of the symbols used. The
data type of every leaf node is shown near the right end of the
corresponding line.
module: ietf-layer0-types
grouping wdm-label-start-end:
+-- (grid-type)?
+--:(fixed-dwdm)
| +-- dwdm-n? dwdm-n
+--:(cwdm)
| +-- cwdm-n? cwdm-n
+--:(flexi-grid)
+-- flexi-n? flexi-n
grouping wdm-label-step:
+-- (l0-grid-type)?
+--:(fixed-dwdm)
| +-- wson-dwdm-channel-spacing? identityref
+--:(cwdm)
| +-- wson-cwdm-channel-spacing? identityref
+--:(flexi-grid)
x-- flexi-grid-channel-spacing? identityref
+-- flexi-ncfg? identityref
+-- flexi-n-step? uint8
grouping wdm-label-hop:
+-- (grid-type)?
+--:(fixed-dwdm)
| +-- (fixed-single-or-super-channel)?
| +--:(single)
| | +-- dwdm-n? dwdm-n
| +--:(multi)
| +-- subcarrier-dwdm-n* dwdm-n
Belotti, et al. Expires 19 December 2025 [Page 65]
Internet-Draft L0 Common YANG Types June 2025
+--:(cwdm)
| +-- cwdm-n? cwdm-n
+--:(flexi-grid)
+-- (single-or-super-channel)?
+--:(single)
| +-- flexi-n? flexi-n
| +-- flexi-m? flexi-m
x--:(super)
| x-- subcarrier-flexi-n* [flexi-n]
| +-- flexi-n? flexi-n
| +-- flexi-m? flexi-m
+--:(multi)
+-- frequency-slots
+-- frequency-slot* [flexi-n]
+-- flexi-n? flexi-n
+-- flexi-m? flexi-m
grouping wdm-label-range-info:
+-- grid-type? identityref
+-- priority? uint8
+-- flexi-grid
+-- slot-width-granularity? identityref
+-- min-slot-width-factor? uint16
+-- max-slot-width-factor? uint16
grouping wson-label-start-end:
+-- (grid-type)?
+--:(dwdm)
| +-- dwdm-n? dwdm-n
+--:(cwdm)
+-- cwdm-n? cwdm-n
grouping wson-label-hop:
+-- (grid-type)?
+--:(dwdm)
| +-- (single-or-super-channel)?
| +--:(single)
| | +-- dwdm-n? dwdm-n
| +--:(super)
| +-- subcarrier-dwdm-n* dwdm-n
+--:(cwdm)
+-- cwdm-n? cwdm-n
grouping l0-label-range-info:
+-- grid-type? identityref
+-- priority? uint8
grouping wson-label-step:
+-- (l0-grid-type)?
+--:(dwdm)
| +-- wson-dwdm-channel-spacing? identityref
+--:(cwdm)
+-- wson-cwdm-channel-spacing? identityref
Belotti, et al. Expires 19 December 2025 [Page 66]
Internet-Draft L0 Common YANG Types June 2025
grouping flexi-grid-label-start-end:
+-- flexi-n? flexi-n
grouping flexi-grid-frequency-slot:
+-- flexi-n? flexi-n
+-- flexi-m? flexi-m
grouping flexi-grid-label-hop:
+-- (single-or-super-channel)?
+--:(single)
| +-- flexi-n? flexi-n
| +-- flexi-m? flexi-m
x--:(super)
| x-- subcarrier-flexi-n* [flexi-n]
| +-- flexi-n? flexi-n
| +-- flexi-m? flexi-m
+--:(multi)
+-- frequency-slots
+-- frequency-slot* [flexi-n]
+-- flexi-n? flexi-n
+-- flexi-m? flexi-m
grouping flexi-grid-label-range-info:
+-- grid-type? identityref
+-- priority? uint8
+-- flexi-grid
+-- slot-width-granularity? identityref
+-- min-slot-width-factor? uint16
+-- max-slot-width-factor? uint16
grouping flexi-grid-label-step:
x-- flexi-grid-channel-spacing? identityref
+-- flexi-ncfg? identityref
+-- flexi-n-step? uint8
grouping transceiver-capabilities:
+--ro supported-modes!
+--ro supported-mode* [mode-id]
+--ro mode-id? string
+--ro (mode)
+--:(G.698.2)
| +--ro standard-mode? standard-mode
| +--ro line-coding-bitrate* identityref
| +--ro transceiver-tuning-range
| | +--ro min-central-frequency?
| | | frequency-thz
| | +--ro max-central-frequency?
| | | frequency-thz
| | +--ro transceiver-tunability-granularity?
| | frequency-ghz
| +--ro tx-channel-power-min? power-dbm
| +--ro tx-channel-power-max? power-dbm
| +--ro rx-channel-power-min? power-dbm
Belotti, et al. Expires 19 December 2025 [Page 67]
Internet-Draft L0 Common YANG Types June 2025
| +--ro rx-channel-power-max? power-dbm
| +--ro rx-total-power-max? power-dbm
+--:(organizational-mode)
| +--ro organizational-mode
| +--ro operational-mode? operational-mode
| +--ro organization-identifier?
| | organization-identifier
| +--ro line-coding-bitrate* identityref
| +--ro transceiver-tuning-range
| | +--ro min-central-frequency?
| | | frequency-thz
| | +--ro max-central-frequency?
| | | frequency-thz
| | +--ro transceiver-tunability-granularity?
| | frequency-ghz
| +--ro tx-channel-power-min? power-dbm
| +--ro tx-channel-power-max? power-dbm
| +--ro rx-channel-power-min? power-dbm
| +--ro rx-channel-power-max? power-dbm
| +--ro rx-total-power-max? power-dbm
+--:(explicit-mode)
+--ro explicit-mode
+--ro transceiver-tuning-range
| +--ro min-central-frequency?
| | frequency-thz
| +--ro max-central-frequency?
| | frequency-thz
| +--ro transceiver-tunability-granularity?
| frequency-ghz
+--ro tx-channel-power-min? power-dbm
+--ro tx-channel-power-max? power-dbm
+--ro rx-channel-power-min? power-dbm
+--ro rx-channel-power-max? power-dbm
+--ro rx-total-power-max? power-dbm
+--ro compatible-modes
+--ro supported-application-code*
| -> ../../../../supported-mode/mode-id
+--ro supported-organizational-mode*
-> ../../../../supported-mode/mode-id
grouping standard-mode:
+--ro standard-mode? standard-mode
grouping organizational-mode:
+--ro operational-mode? operational-mode
+--ro organization-identifier? organization-identifier
grouping penalty-value:
+--ro penalty-value union
grouping explicit-mode:
+--ro line-coding-bitrate? identityref
Belotti, et al. Expires 19 December 2025 [Page 68]
Internet-Draft L0 Common YANG Types June 2025
+--ro bitrate? uint16
+--ro max-diff-group-delay? decimal-2
+--ro max-chromatic-dispersion? decimal-2
+--ro cd-penalty* [cd-value]
| +--ro cd-value decimal-2
| +--ro penalty-value union
+--ro max-polarization-mode-dispersion? decimal-2
+--ro pmd-penalty* [pmd-value]
| +--ro pmd-value decimal-2
| +--ro penalty-value union
+--ro max-polarization-dependent-loss power-loss-or-null
+--ro pdl-penalty* [pdl-value]
| +--ro pdl-value power-loss
| +--ro penalty-value union
+--ro available-modulation-type? identityref
+--ro min-OSNR? snr
+--ro rx-ref-channel-power? power-dbm
+--ro rx-channel-power-penalty* [rx-channel-power-value]
| +--ro rx-channel-power-value power-dbm
| +--ro penalty-value union
+--ro min-Q-factor? decimal-2
+--ro available-baud-rate? decimal64
+--ro roll-off? decimal64
+--ro min-carrier-spacing? frequency-ghz
+--ro available-fec-type? identityref
+--ro fec-code-rate? decimal64
+--ro fec-threshold? decimal64
+--ro in-band-osnr? snr
+--ro out-of-band-osnr? snr
+--ro tx-polarization-power-difference? power-ratio
+--ro polarization-skew? decimal-2
grouping common-standard-organizational-mode:
+--ro line-coding-bitrate* identityref
grouping transceiver-tuning-range:
+-- min-central-frequency? frequency-thz
+-- max-central-frequency? frequency-thz
+-- transceiver-tunability-granularity? frequency-ghz
grouping common-all-modes:
+--ro transceiver-tuning-range
| +--ro min-central-frequency? frequency-thz
| +--ro max-central-frequency? frequency-thz
| +--ro transceiver-tunability-granularity? frequency-ghz
+--ro tx-channel-power-min? power-dbm
+--ro tx-channel-power-max? power-dbm
+--ro rx-channel-power-min? power-dbm
+--ro rx-channel-power-max? power-dbm
+--ro rx-total-power-max? power-dbm
grouping common-transceiver-param:
Belotti, et al. Expires 19 December 2025 [Page 69]
Internet-Draft L0 Common YANG Types June 2025
+-- line-coding-bitrate? identityref
+-- tx-channel-power? power-dbm-or-null
+--ro rx-channel-power? power-dbm-or-null
+--ro rx-total-power? power-dbm-or-null
grouping common-transceiver-configured-param:
+-- line-coding-bitrate? identityref
+-- tx-channel-power? power-dbm-or-null
grouping common-transceiver-readonly-param:
+--ro rx-channel-power? power-dbm-or-null
+--ro rx-total-power? power-dbm-or-null
grouping tunnel-attributes:
+-- wavelength-assignment? identityref
grouping frequency-range:
+-- lower-frequency frequency-thz
+-- upper-frequency frequency-thz
grouping frequency-range-with-identifier:
+-- frequency-range-id? uint16
+-- frequency-range
+-- lower-frequency frequency-thz
+-- upper-frequency frequency-thz
grouping path-constraints:
+-- gsnr-extra-margin? snr
grouping path-properties:
+--ro estimated-gsnr? snr
+--ro estimated-eol-gsnr? snr
+--ro estimated-lowest-gsnr? snr
Figure 2
Appendix B. Changes from RFC 9093
This version adds new identities, data types, and groupings to the
'ietf-layer0-types' YANG module.
The following new YANG identities have been added to the 'ietf-
layer0-types' module:
* cwdm-ch-spc-type
* flexi-ncfg-type
* flexi-ncfg-6p25gh
* modulation
* DPSK
* QPSK
Belotti, et al. Expires 19 December 2025 [Page 70]
Internet-Draft L0 Common YANG Types June 2025
* DP-QPSK
* QAM8
* DP-QAM8
* QAM16
* DP-QAM16
* QAM32
* DP-QAM32
* QAM64
* DP-QAM64
* fec-type
* g-fec
* super-fec
* no-fec
* sc-fec
* o-fec
* c-fec
* line-coding
* line-coding-NRZ-2p5G
* line-coding-NRZ-OTU1
* line-coding-NRZ-10G
* line-coding-NRZ-OTU2
* line-coding-OTL4.4-SC
* line-coding-FOIC1.4-SC
* wavelength-assignment
Belotti, et al. Expires 19 December 2025 [Page 71]
Internet-Draft L0 Common YANG Types June 2025
* first-fit-wavelength-assignment
* random-wavelength-assignment
* least-loaded-wavelength-assignment
* lower-first-wavelength-assignment
* upper-first-wavelength-assignment
* type-power-mode
* power-spectral-density
* carrier-power
* switching-wson-lsc
* switching-flexi-grid-lsc
The following new YANG data types have been added to the 'ietf-
layer0-types' module:
* Standard-mode
* Organization-identifier
* Operational-mode
* frequency-thz
* frequency-ghz
* snr
* snr-or-null
* fiber-type
* decimal-2
* decimal-2-or-null
* power-gain
* power-gain-or-null
* power-loss
Belotti, et al. Expires 19 December 2025 [Page 72]
Internet-Draft L0 Common YANG Types June 2025
* power-loss-or-null
* power-ratio
* power-ratio-or-null
* power-dbm
* power-dbm-or-null
* decimal-5
* decimal-5-or-null
* psd
* psd-or-null
The following new YANG groupings have been added to the 'ietf-
layer0-types' module:
* wdm-label-start-end
* wdm-label-step
* wdm-label-hop
* wdm-label-range-info
* transceiver-capabilities
* standard-mode
* organizational-mode
* penalty-value
* explicit-mode
* common-standard-organizational-mode
* transceiver-tuning-range
* common-all-mode
* common-transceiver-param
* common-transceiver-configured-param
Belotti, et al. Expires 19 December 2025 [Page 73]
Internet-Draft L0 Common YANG Types June 2025
* common-transceiver-readonly-param
* tunnel-attributes
* frequency-range
* frequency-range-with-identifier
* path-constraints
* path-properties
Acknowledgments
The authors and the working group give their sincere thanks to Robert
Wilton for the YANG doctor review and to Adrian Farrel and Tom Petch
for their comments during the model and document development.
This document was prepared using kramdown.
Contributors
Haomian Zheng
Huawei
Email: zhenghaomian@huawei.com
Daniel King
University of Lancaster
Email: d.king@lancaster.ac.uk
Gabriele Galimberti
Nokia
Email: gabriele.galimberti@nokia.com
Enrico Griseri
Nokia
Email: Enrico.Griseri@nokia.com
Dhruv Dhody
Huawei
Email: dhruv.ietf@gmail.com
Belotti, et al. Expires 19 December 2025 [Page 74]
Internet-Draft L0 Common YANG Types June 2025
Bin Yeong Yoon
ETRI
Email: byyun@etri.re.kr
Ricard Vilalta
CTTC
Email: ricard.vilalta@cttc.es
Young Lee
Samsung
Email: younglee.tx@gmail.com
Victor Lopez
Nokia
Email: victor.lopez@nokia.com
Roberto Manzotti
Cisco
Email: rmanzott@cisco.com
Gert Grammel
Juniper
Email: ggrammel@juniper.net
Authors' Addresses
Sergio Belotti (editor)
Nokia
Email: sergio.belotti@nokia.com
Italo Busi (editor)
Huawei
Email: italo.busi@huawei.com
Dieter Beller (editor)
Nokia
Email: dieter.beller@nokia.com
Belotti, et al. Expires 19 December 2025 [Page 75]
Internet-Draft L0 Common YANG Types June 2025
Esther Le Rouzic
Orange
Email: esther.lerouzic@orange.com
Aihua Guo
Futurewei Technologies
Email: aihuaguo.ietf@gmail.com
Belotti, et al. Expires 19 December 2025 [Page 76]