DetNet Data Plane: MPLS
draft-ietf-detnet-mpls-00
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 8964.
|
|
|---|---|---|---|
| Authors | Balazs Varga , János Farkas , Lou Berger , Don Fedyk , Andrew G. Malis , Stewart Bryant , Jouni Korhonen | ||
| Last updated | 2019-06-08 (Latest revision 2019-05-06) | ||
| Replaces | draft-ietf-detnet-dp-sol-mpls | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
TSVART Last Call review
(of
-05)
by Michael Tüxen
Ready w/issues
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Document | |
| Document shepherd | (None) | ||
| IESG | IESG state | Became RFC 8964 (Proposed Standard) | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-detnet-mpls-00
DetNet B. Varga, Ed.
Internet-Draft J. Farkas
Intended status: Standards Track Ericsson
Expires: November 6, 2019 L. Berger
D. Fedyk
LabN Consulting, L.L.C.
A. Malis
S. Bryant
Huawei Technologies
J. Korhonen
May 5, 2019
DetNet Data Plane: MPLS
draft-ietf-detnet-mpls-00
Abstract
This document specifies the Deterministic Networking data plane when
operating over an MPLS Packet Switched Networks.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 6, 2019.
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Varga, et al. Expires November 6, 2019 [Page 1]
Internet-Draft DetNet MPLS May 2019
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Terms Used in This Document . . . . . . . . . . . . . . . 3
2.2. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 4
3. Requirements Language . . . . . . . . . . . . . . . . . . . . 5
4. DetNet MPLS Data Plane Overview . . . . . . . . . . . . . . . 5
4.1. Layers of DetNet Data Plane . . . . . . . . . . . . . . . 5
4.2. DetNet MPLS Data Plane Scenarios . . . . . . . . . . . . 6
5. MPLS-Based DetNet Data Plane Solution . . . . . . . . . . . . 8
5.1. DetNet Over MPLS Encapsulation Components . . . . . . . . 8
5.2. MPLS Data Plane Encapsulation . . . . . . . . . . . . . . 9
5.2.1. DetNet Control Word and the DetNet Sequence Number . 10
5.2.2. S-Labels . . . . . . . . . . . . . . . . . . . . . . 12
5.2.3. F-Labels . . . . . . . . . . . . . . . . . . . . . . 14
5.3. OAM Indication . . . . . . . . . . . . . . . . . . . . . 17
5.4. Flow Aggregation . . . . . . . . . . . . . . . . . . . . 17
5.4.1. Aggregation at the LSP . . . . . . . . . . . . . . . 17
5.4.2. Aggregating DetNet Flows as a new DetNet flow . . . . 18
5.4.3. Simple Aggregation at the DetNet Layer . . . . . . . 19
5.5. Service Sub-Layer Considerations . . . . . . . . . . . . 19
5.5.1. Edge Node Processing . . . . . . . . . . . . . . . . 20
5.5.2. Relay Node Processing . . . . . . . . . . . . . . . . 20
5.6. Forwarding Sub-Layer Considerations . . . . . . . . . . . 20
5.6.1. Class of Service . . . . . . . . . . . . . . . . . . 20
5.6.2. Quality of Service . . . . . . . . . . . . . . . . . 21
6. Flow Identification Management and Control Information . . . 22
7. Security Considerations . . . . . . . . . . . . . . . . . . . 22
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22
9. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 22
10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 23
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 24
11.1. Normative References . . . . . . . . . . . . . . . . . . 24
11.2. Informative References . . . . . . . . . . . . . . . . . 26
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 28
1. Introduction
Deterministic Networking (DetNet) is a service that can be offered by
a network to DetNet flows. DetNet provides these flows extremely low
packet loss rates and assured maximum end-to-end delivery latency.
Varga, et al. Expires November 6, 2019 [Page 2]
Internet-Draft DetNet MPLS May 2019
General background and concepts of DetNet can be found in
[I-D.ietf-detnet-architecture].
The DetNet Architecture models the DetNet related data plane
functions decomposed into two sub-layers: a service sub-layer and a
forwarding sub-layer. The service sub-layer is used to provide
DetNet service functions such as protection and reordering. The
forwarding sub-layer is used to provide forwarding assurance (low
loss, assured latency, and limited reordering).
This document specifies the DetNet data plane operation and the on-
wire encapsulation of DetNet flows over an MPLS-based Packet Switched
Network (PSN) using the service sub-layer reference model. MPLS
encapsulation already provides a solid foundation of building blocks
to enable the DetNet service and forwarding sub-layer functions.
MPLS encapsulated DetNet can be carried over a variety of different
network technologies that can provide the DetNet required level of
service. However, the specific details of how DetNet MPLS is carried
over different network technologies is out of scope of this document.
MPLS encapsulated DetNet flows can carry different types of traffic.
The details of the types of traffic that are carried in DetNet are
also out of scope of this document. An example of IP using DetNet
MPLS sub-networks can be found in [I-D.ietf-detnet-ip]. DetNet MPLS
may use an associated controller and Operations, Administration, and
Maintenance (OAM) functions that are defined outside of this
document.
Important background information common to all data planes for DetNet
can be found in the DetNet Data Plane Framework
[I-D.ietf-detnet-data-plane-framework].
2. Terminology
2.1. Terms Used in This Document
This document uses the terminology established in the DetNet
architecture [I-D.ietf-detnet-architecture] and the the DetNet Data
Plane Framework [I-D.ietf-detnet-data-plane-framework]. The reader
is assumed to be familiar with these documents and any terminology
defined therein.
The following terminology is introduced in this document:
F-Label A Detnet "forwarding" label that identifies the LSP
used to forward a DetNet flow across an MPLS PSN, e.g.,
a hop-by-hop label used between label switching routers
(LSR).
Varga, et al. Expires November 6, 2019 [Page 3]
Internet-Draft DetNet MPLS May 2019
S-Label A DetNet "service" label that is used between DetNet
nodes that implement also the DetNet service sub-layer
functions. An S-Label is also used to identify a
DetNet flow at DetNet service sub-layer.
d-CW A DetNet Control Word (d-CW) is used for sequencing
information of a DetNet flow at the DetNet service sub-
layer.
2.2. Abbreviations
The following abbreviations are used in this document:
AC Attachment Circuit.
CE Customer Edge equipment.
CoS Class of Service.
CW Control Word.
DetNet Deterministic Networking.
DF DetNet Flow.
DN-IWF DetNet Inter-Working Function.
L2 Layer 2.
L2VPN Layer 2 Virtual Private Network.
L3 Layer 3.
LSR Label Switching Router.
MPLS Multiprotocol Label Switching.
MPLS-TE Multiprotocol Label Switching - Traffic Engineering.
MPLS-TP Multiprotocol Label Switching - Transport Profile.
MS-PW Multi-Segment PseudoWire (MS-PW).
NSP Native Service Processing.
OAM Operations, Administration, and Maintenance.
PE Provider Edge.
Varga, et al. Expires November 6, 2019 [Page 4]
Internet-Draft DetNet MPLS May 2019
PEF Packet Elimination Function.
PRF Packet Replication Function.
PREOF Packet Replication, Elimination and Ordering Functions.
POF Packet Ordering Function.
PSN Packet Switched Network.
PW PseudoWire.
QoS Quality of Service.
S-PE Switching Provider Edge.
T-PE Terminating Provider Edge.
TSN Time-Sensitive Network.
3. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
4. DetNet MPLS Data Plane Overview
4.1. Layers of DetNet Data Plane
MPLS provides a wide range of capabilities that can be utilised by
DetNet. A straight forward approach utilizing MPLS for a DetNet
service sub-layer is based on the existing pseudowire (PW)
encapsulations and by utilizing existing MPLS Traffic Engineering
encapsulations and mechanisms. Background on PWs can be found in
[RFC3985] and [RFC3031]. Background on MPLS Traffic Engineering can
be found in [RFC3272] and [RFC3209].
Varga, et al. Expires November 6, 2019 [Page 5]
Internet-Draft DetNet MPLS May 2019
DetNet MPLS
.
Bottom of Stack .
(inner label) +------------+
| Service | d-CW, S-Label
+------------+
| Forwarding | F-Label(s)
+------------+
Top of Stack .
(outer label) .
Figure 1: DetNet Adaptation to MPLS Data Plane
The DetNet MPLS data plane representation is illustrated in Figure 1.
The service sub-layer includes a DetNet control word (d-CW) and a
identifying service label (S-Label). The DetNet control word (d-CW)
conforms to the Generic PW MPLS Control Word (PWMCW) defined in
[RFC4385].
A node operating on a DetNet flow in the Detnet service sub-
layer,uses the local context associated with that S-Label, provided
by a received F-Label, to determine what local DetNet operation(s)
are applied to that packet. An S-Label may be taken from the
platform label space [RFC3031], making it unique, enabling DetNet
flow identification regardless of which input interface or LSP the
packet arrives on.
The DetNet forwarding sub-layer is supported by one or more
forwarding labels (F-Labels). MPLS Traffic Engineering
encapsulations and mechanisms can be utilized to provide a forwarding
sub-layer that is responsible for providing resource allocation and
explicit routes.
4.2. DetNet MPLS Data Plane Scenarios
Varga, et al. Expires November 6, 2019 [Page 6]
Internet-Draft DetNet MPLS May 2019
DetNet MPLS Relay Transit Relay DetNet MPLS
End System Node Node Node End System
(T-PE) (S-PE) (LSR) (S-PE) (T-PE)
+----------+ +----------+
| Appl. |<------------ End to End Service ----------->| Appl. |
+----------+ +---------+ +---------+ +----------+
| Service |<--| Service |-- DetNet flow --| Service |-->| Service |
+----------+ +---------+ +----------+ +---------+ +----------+
|Forwarding| |Fwd| |Fwd| |Forwarding| |Fwd| |Fwd| |Forwarding|
+-------.--+ +-.-+ +-.-+ +----.---.-+ +-.-+ +-.-+ +---.------+
: Link : / ,-----. \ : Link : / ,-----. \
+........+ +-[ Sub ]-+ +......+ +-[ Sub ]-+
[Network] [Network]
`-----' `-----'
|<- LSP -->| |<-------- LSP -----------| |<--- LSP -->|
|<----------------- DetNet MPLS --------------------->|
Figure 2: A DetNet MPLS Network
Figure 2 illustrates a hypothetical DetNet MPLS-only network composed
of DetNet aware MPLS enabled end systems, operating over a DetNet
aware MPLS network. In this figure, the relay nodes are PE devices
that define the MPLS LSP boundaries and the transit nodes are LSRs.
DetNet end system and relay nodes understand the particular needs of
DetNet flows and provide both DetNet service and forwarding sub-layer
functions. In the case of MPLS, DetNet nodes add, remove and process
d-CWs, S-Labels and F-labels as needed. DetNet MPLS nodes provide
functionality analogous to T-PEs when they sit at the edge of an MPLS
domain, and S-PEs when they are in the middle of an MPLS domain, see
[RFC6073].
In a DetNet MPLS network, transit nodes may be DetNet service aware
or may be DetNet unaware MPLS Label Switching Routers (LSRs). In
this latter case, such LSRs would be unaware of the special
requirements of the DetNet service sub-layer, but would still provide
traffic engineering functions and the QoS capabilities needed to
ensure that the (TE) LSPs meet the service requirements of the
carried DetNet flows.
The application of DetNet using MPLS supports a number of control
plane/management plane types. These types support certain MPLS data
plane deployments. For example RSVP-TE, MPLS-TP, or MPLS Segment
Routing (when extended to support resource allocation) are all valid
MPLS deployment cases.
Varga, et al. Expires November 6, 2019 [Page 7]
Internet-Draft DetNet MPLS May 2019
Figure 3 illustrates how an end-to-end MPLS-based DetNet service is
provided in a more detail. In this figure, the customer end systems,
CE1 and CE2, are able to send and receive MPLS encapsulated DetNet
flows, and R1, R2 and R3 are relay nodes in the middle of a DetNet
network. The 'X' in the end systems, and relay nodes represents
potential DetNet compound flow packet replication and elimination
points. In this example, service protection is supported utilizing
least two DetNet member flows and TE LSPs. For a unidirectional
flow, R1 supports PRF and R3 supports PEF and POF. Note that the
relay nodes may change the underlying forwarding sub-layer, for
example tunneling MPLS over IEEE 802.1 TSN
[I-D.ietf-detnet-mpls-over-tsn], or simply over interconnect network
links.
DetNet DetNet
MPLS Service Transit Transit Service MPLS
DetNet | |<-Tnl->| |<-Tnl->| | DetNet
End | V 1 V V 2 V | End
System | +--------+ +--------+ +--------+ | System
+---+ | | R1 |=======| R2 |=======| R3 | | +---+
| X...DFa...|._X_....|..DF1..|.__ ___.|..DF3..|...._X_.|.DFa..|.X |
|CE1|========| \ | | X | | / |======|CE2|
| | | | \_.|..DF2..|._/ \__.|..DF4..|._/ | | | |
+---+ | |=======| |=======| | +---+
^ +--------+ +--------+ +--------+ ^
| Relay Node Relay Node Relay Node |
| (S-PE) (S-PE) (S-PE) |
| |
|<---------------------- DetNet MPLS --------------------->|
| |
|<--------------- End to End DetNet Service -------------->|
-------------------------- Data Flow ------------------------->
X = Optional service protection (none, PRF, PREOF, PEF/POF)
DFx = DetNet member flow x over a TE LSP
Figure 3: MPLS-Based Native DetNet
5. MPLS-Based DetNet Data Plane Solution
5.1. DetNet Over MPLS Encapsulation Components
To carry DetNet over MPLS the following is required:
1. A method of identifying the MPLS payload type.
Varga, et al. Expires November 6, 2019 [Page 8]
Internet-Draft DetNet MPLS May 2019
2. A method of identifying the DetNet flow group to the processing
element.
3. A method of distinguishing DetNet OAM packets from DetNet data
packets.
4. A method of carrying the DetNet sequence number.
5. A suitable LSP to deliver the packet to the egress PE.
6. A method of carrying queuing and forwarding indication.
In this design an MPLS service label (the S-Label), similar to a
pseudowire (PW) label [RFC3985], is used to identify both the DetNet
flow identity and the payload MPLS payload type satisfying (1) and
(2) in the list above. OAM traffic discrimination happens through
the use of the Associated Channel method described in [RFC4385]. The
DetNet sequence number is carried in the DetNet Control word which
carries the Data/OAM discriminator. To simplify implementation and
to maximize interoperability two sequence number sizes are supported:
a 16 bit sequence number and a 28 bit sequence number. The 16 bit
sequence number is needed to support some types of legacy clients.
The 28 bit sequence number is used in situations where it is
necessary ensure that in high speed networks the sequence number
space does not wrap whilst packets are in flight.
The LSP used to forward the DetNet packet may be of any type (MPLS-
LDP, MPLS-TE, MPLS-TP [RFC5921], or MPLS-SR
[I-D.ietf-spring-segment-routing-mpls]). The LSP (F-Label) label
and/or the S-Label may be used to indicate the queue processing as
well as the forwarding parameters. Note that the possible use of
Penultimate Hop Popping (PHP) means that the S-Label may be the only
label received at the terminating DetNet service.
5.2. MPLS Data Plane Encapsulation
Figure 4 illustrates a DetNet data plane MPLS encapsulation. The
MPLS-based encapsulation of the DetNet flows is well suited for the
scenarios described in [I-D.ietf-detnet-data-plane-framework].
Furthermore, an end to end DetNet service i.e., native DetNet
deployment (see Section 4.2) is also possible if DetNet end systems
are capable of initiating and termination MPLS encapsulated packets.
The MPLS-based DetNet data plane encapsulation consists of:
o DetNet control word (d-CW) containing sequencing information for
packet replication and duplicate elimination purposes, and the OAM
indicator.
Varga, et al. Expires November 6, 2019 [Page 9]
Internet-Draft DetNet MPLS May 2019
o DetNet service Label (S-Label) that identifies a DetNet flow at
the receiving DetNet service sub-layer processing node.
o Zero or more Detnet MPLS Forwarding label(s) (F-Label) used to
direct the packet along the label switched path (LSP) to the next
service sub-layer processing node along the path. When
Penultimate Hop Popping is in use there may be no label F-Label in
the protocol stack on the final hop.
o The necessary data-link encapsulation is then applied prior to
transmission over the physical media.
DetNet MPLS-based encapsulation
+---------------------------------+
| |
| DetNet App-Flow |
| Payload Packet |
| |
+---------------------------------+ <--\
| DetNet Control Word | |
+---------------------------------+ +--> DetNet data plane
| S-Label | | MPLS encapsulation
+---------------------------------+ |
| F-Label(s) | |
+---------------------------------+ <--/
| Data-Link |
+---------------------------------+
| Physical |
+---------------------------------+
Figure 4: Encapsulation of a DetNet App-Flow in an MPLS(-TP) PSN
5.2.1. DetNet Control Word and the DetNet Sequence Number
A DetNet control word (d-CW) conforms to the Generic PW MPLS Control
Word (PWMCW) defined in [RFC4385]. The d-CW formatted as shown in
Figure 5 MUST be present in all DetNet packets containing app-flow
data.
Varga, et al. Expires November 6, 2019 [Page 10]
Internet-Draft DetNet MPLS May 2019
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 0| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: DetNet Control Word
(bits 0 to 3)
Per [RFC4385], MUST be set to zero (0).
Sequence Number (bits 4 to 31)
An unsigned value implementing the DetNet sequence number.
A separate sequence number space MUST be maintained by the node that
adds the d-CW for each DetNet app-flow. The following sequence
number field lengths MUST be supported:
0 bits
16 bits
28 bits
The sequence number length MUST be provisioned (configured) on a per
app-flow basis via configuration, e.g., the controller plane
described in [I-D.ietf-detnet-data-plane-framework].
A 0 bit sequence number field length indicates that there is no
DetNet sequence number used for the flow. When the length is zero,
the sequence number field MUST be set to zero (0) on all packets sent
for the flow.
When the sequence number field length is 16 or 28 bits for a flow,
the sequence number MUST be incremented by one for each new app-flow
packet sent. When the field length is 16 bits, d-CW bits 4 to 15
MUST be set to zero (0). This values carried in this field can wrap
and it is important to note that zero (0) is a valid field value.
For example, were the sequence number size is 16 bits, the sequence
will contain: 65535, 0, 1. In this case, zero (0) is an ordinary
sequence number. This differs from [RFC4448] where a sequence number
of zero (0) does not indicate that no sequence number field value is
in use.
Varga, et al. Expires November 6, 2019 [Page 11]
Internet-Draft DetNet MPLS May 2019
The sequence number is optionally used during receive processing as
described below in Section 5.2.2.1 and Section 5.2.2.2.
5.2.2. S-Labels
App-flow identification at a DetNet service sub-layer is realized by
an S-Label. Each app-flow MUST be sent by the node that adds a d-CW
with a single specific S-Label value. MPLS-aware DetNet end systems
and edge nodes, which are by definition MPLS ingress and egress
nodes, MUST add and remove the d-CW and S-Label. Relay nodes MAY
swap S-Label values when processing an app-flow.
The S-Label value MUST be provisioned per app-flow via configuration,
e.g., via the controller plane described in
[I-D.ietf-detnet-data-plane-framework]. Note that S-Labels provide
app-flow identification at the downstream DetNet service sub-layer
receiver, not the sender. As such, S-Labels MUST be allocated by the
entity that controls the service sub-layer receiving node's label
space, and MAY be allocated from the platform label space [RFC3031].
The S-Label will normally be at the bottom of the label stack once
the last F-Label is removed, immediately preceding the d-CW. To
support service sub-layer level OAM, an OAM Associated Channel Header
(ACH) [RFC4385] together with a Generic Associated Channel Label
(GAL) [RFC5586] MAY be used in place of a d-CW.
Similarly, an Entropy Label Indicator/Entropy Label (ELI/EL)
[RFC6790] MAY be carried below the S-Label in the label stack in
networks where DetNet flows would otherwise received ECMP treatment.
When ELs are used, the same EL value SHOULD be used for all of the
packets sent using a specific S-Label to force the flow to follow the
same path. However, as outlines in
[I-D.ietf-detnet-data-plane-framework] the use of ECMP for DetNet
flows is NOT RECOMMENDED. ECMP MAY be used for non-DetNet flows
within a DetNet domain.
When receiving a DetNet MPLS flow, an implementation MUST identify
the app-flow associated with the incoming packet based on the
S-Label. When a node is using platform labels for S-Labels, no
additional information is needed as the S-label uniquely identifies
the app-flow. In the case where platform labels are not used, one or
more F-Labels proceeding the S-Label MUST be used together with the
S-Label to uniquely identify the incoming app-flows. When PHP is
used, the incoming interface MAY also be used to together with any
present F-Label(s) and the S-Label to uniquely identify an incoming
app-flows. Note that choice to use platform label space for S-Label
or S-Label plus one or more F-Labels to identify app flows is a local
implementation choice, with one caveat. When one or more F-labels,
Varga, et al. Expires November 6, 2019 [Page 12]
Internet-Draft DetNet MPLS May 2019
or incoming interface, is needed together with an S-Label to uniquely
identify, the controller plane MUST ensure that incoming DetNet MPLS
packets arrive with the needed information (F-label(s) and/or
incoming interface); the details of such are outside the scope of
this document.
The use of platform labels for S-Labels matches other pseudowire
encapsulations for consistency but there is no hard requirement in
this regard.
5.2.2.1. Packet Elimination Function Processing
Implementations MAY support the Packet Elimination Function (PEF) for
received DetNet MPLS flows. When supported, use of the PEF for a
particular app-flow MUST be provisioned via configuration, e.g., via
the controller plane described in
[I-D.ietf-detnet-data-plane-framework].
After an app-flow is identified for a received DetNet MPLS packet, as
described above, an implementation MUST check if PEF is configured
for that app-flow. When configured the implementation MUST track the
sequence number contained in received d-CWs and MUST ensure that
duplicate (replicated) instances of a particular sequence number are
discarded. The specific mechanisms used for an implementation to
identify which received packets are duplicates and which are new is
an implementation choice. Note that per Section 5.2.1 the sequence
number field length may be 16 or 28 bits, and the field value can
wrap.
Note that an implementation MAY wish to constrain the maximum number
sequence numbers that are tracked, on platform-wide or per flow
basis. Some implementations MAY support the provisioning of the
maximum number sequence numbers that are tracked number on either a
platform-wide or per flow basis.
5.2.2.2. Packet Ordering Function Processing
A function that is related to PEF is the Packet Ordering Function
(POF). Implementations MAY support POF. When supported, use of the
POF for a particular app-flow MUST be provisioned via configuration,
e.g., via the controller plane described by
[I-D.ietf-detnet-data-plane-framework]. Implementations MAY required
that PEF and POF be used in combination. There is no requirement
related to the order of execution of the Packet Elimination and
Ordering Functions in an implementation.
After an app-flow is identified for a received DetNet MPLS packet, as
described above, an implementation MUST check if POF is configured
Varga, et al. Expires November 6, 2019 [Page 13]
Internet-Draft DetNet MPLS May 2019
for that app-flow. When configured the implementation MUST track the
sequence number contained in received d-CWs and MUST ensure that
packets are processed in the order indicated in the received d-CW
sequence number field, which may not be in the order the packets are
received. As defined in Section 5.2.1 the sequence number field
length may be 16 or 28 bits, is incremented by one (1) for each new
app-flow packet sent, and the field value can wrap. The specific
mechanisms used for an implementation to identify the order of
received packets is an implementation choice.
Note that an implementation MAY wish to constrain the maximum number
of out of order packets that can be processed, on platform-wide or
per flow basis. Some implementations MAY support the provisioning of
this number on either a platform-wide or per flow basis. The number
of out of order packets that can be processed also impacts the
latency of a flow.
5.2.3. F-Labels
F-Labels are supported the DetNet forwarding sub-layer. F-Labels are
used to provide LSP-based connectivity between DetNet service sub-
layer processing nodes.
5.2.3.1. Service Sub-Layer and Packet Replication Function Processing
DetNet MPLS end systems, edge nodes and relay nodes may operate at
the DetNet service sub-layer with understand of app-flows and their
requirements. As mentioned earlier, when operating at this layer
such nodes can push, pop or swap (pop then push) S-Labels. In all
cases, the F-Labels used for the app-flow are always replaced and the
following procedures apply.
When sending a DetNet flow, Zero or more F-Labels MAY be added on top
of an S-Label by the node pushing an S-Label. The F-Labels to be
pushed when sending a particular app-flow MUST be provisioned per
app-flow via configuration, e.g., via the controller plane discussed
in [I-D.ietf-detnet-data-plane-framework]. To allow for the omission
of F-Labels, an implementation SHOULD also allow an outgoing
interface to be provisioned.
The Packet Replication Function (PRF) function MAY be supported by an
implementation for outgoing DetNet flows. When replication is
supported, the same app-flow data will be sent over multiple outgoing
forwarding sub-layer LSPs. To support PRF an implementation MUST
support the setting of different sets of F-Labels. Therefore, to
allow for the omission of F-Labels, an implementation SHOULD also
allow multiple outgoing interfaces to be provisioned. PRF MUST NOT
Varga, et al. Expires November 6, 2019 [Page 14]
Internet-Draft DetNet MPLS May 2019
be used with app-flows configured with a d-CW sequence number field
length of 0 bits.
When a single set of F-Labels is provisioned for a particular
outgoing app-flow, that set of F-labels MUST be pushed after the
S-Label is pushed. The outgoing packet is then forwarded as
described below in Section 5.2.3.2. When a single outgoing interface
is provisioned, the outgoing packet is then forwarded as described
below in Section 5.2.3.2.
When multiple sets of F-Labels or interfaces are provisioned for a
particular outgoing app-flow, a copy of the outgoing packet,
including the pushed S-Label, MUST be made per F-label set and
outgoing interface. Each set of provisioned F-Labels are then pushed
onto a copy of the packet. Each copy is then forwarded as described
below in Section 5.2.3.2.
As described in the previous section, when receiving a DetNet MPLS
flow, an implementation identifies the app-flow associated with the
incoming packet based on the S-Label. When a node is using platform
labels for S-Labels, any F-Labels can be popped and the S-label
uniquely identifies the app-flow. In the case where platform labels
are not used, F-Label(s) MUST also be provisioned for incoming app-
flows. When PHP is used, incoming interface MUST be provisioned.
The provisioned information MUST then be used to identify incoming
app-flows based on the combination of S-Label and F-Label(s) or
incoming interface.
5.2.3.2. Common F-Label Processing
All DetNet aware MPLS nodes process F-Labels as needed to meet the
service requirements of the DetNet flow or flows carried in the LSPs
represented by the F-Labels. This includes normal push, pop and swap
operations. Such processing is essentially the same type of
processing enabled for TE LSPs, although the specific service
parameters, or traffic specification, can differ. When the DetNet
service parameters of the app-flow or flows carried in an LSP
represented by an F-Label can be met by an exiting TE mechanism, the
forwarding sub-layer processing node MAY be a DetNet unaware, i.e.,
standard, MPLS LSR. Such TE LSPs may provide LSP forwarding service
as defined in, but not limited to, [RFC3209], [RFC3270], [RFC3272],
[RFC3473], [RFC4875], [RFC5440], and [RFC6006].
More specifically, as mentioned above, the DetNet forwarding sub-
layer provides explicit routes and allocated resources, and F-Labels
are used to map to each. Explicit routes are supported based on the
topmost (outermost) F-Label that is pushed or swapped and the LSP
that corresponds to this label. This topmost (outgoing) label MUST
Varga, et al. Expires November 6, 2019 [Page 15]
Internet-Draft DetNet MPLS May 2019
be associated with a provisioned outgoing interface and, for non-
point-to-point outgoing interfaces, a next hop LSR. Note that this
information MUST be provisioned via configuration or the controller
plane. In the previously mentioned special case where there is no
added F-labels and the outgoing interface is not a point-to-point
interface, the outgoing interface MUST also be associated with a next
hop LSR.
Resources may be allocated in a hierarchical fashion per LSP that is
represented by each F-Label. Each LSP MAY be provisioned with a
service parameters that dictates the specific traffic treatment to be
received by the traffic carried over that LSP. Implementations of
this document MUST ensure that traffic carried over each LSP
represented by an F-Label receives the traffic treatment provisioned
for that LSP. Typical mechanisms used to provide different treatment
to different flows includes the allocation of system resources (such
as queues and buffers) and provisioning or related parameters (such
as shaping, and policing). Support can also be provided via an
underlying network technology such IEEE802.1 TSN
[I-D.ietf-detnet-mpls-over-tsn]. Other than in the TSN case, the
specific mechanisms used by a DetNet node to ensure DetNet service
delivery requirements are met for supported DetNet flows is outside
the scope of this document.
Packets that are marked in a way that does not correspond to
allocated resources, e.g., lack a provisioned F-Label, can disrupt
the QoS offered to properly reserved DetNet flows by using resources
allocated to the reserved flows. Therefore, the network nodes of a
DetNet network:
o MUST defend the DetNet QoS by discarding or remarking (to an
allocated DetNet flow or non-competing non-DetNet flow) packets
received that are not associated with a completed resource
allocation.
o MUST NOT use a DetNet allocated resource, e.g. a queue or shaper
reserved for DetNet flows, for any packet that does match the
corresponding DetNet flow.
o MUST ensure a QoS flow does not exceed its allocated resources or
provisioned service level,
o MUST ensure a CoS flow or service class does not impact the
service delivered to other flows. This requirement is similar to
requirement for MPLS LSRs to that CoS LSPs do not impact the
resources allocated to TE LSPs, e.g., via [RFC3473].
Varga, et al. Expires November 6, 2019 [Page 16]
Internet-Draft DetNet MPLS May 2019
Subsequent sections provide additional considerations related to CoS
(Section 5.6.1), QoS (Section 5.6.2) and aggregation (Section 5.4).
5.3. OAM Indication
OAM follows the procedures set out in [RFC5085] with the restriction
that only Virtual Circuit Connectivity Verification (VCCV) type 1 is
supported.
As shown in Figure 3 of [RFC5085] when the first nibble of the d-CW
is 0x0 the payload following the d-CW is normal user data. However,
when the first nibble of the d-CW is 0X1, the payload that follows
the d-DW is an OAM payload with the OAM type indicated by the value
in the d-CW Channel Type field.
The reader is referred to [RFC5085] for a more detailed description
of the Associated Channel mechanism, and to the DetNet work on OAM
for more information DetNet OAM.
5.4. Flow Aggregation
[Author's note: need to revisit this section and ensure that we cover
(and fully specify) desired types of aggregation.]
1. Aggregate at the LSP (Forwarding)
2. Aggregating DetNet flows as a new DetNet flow
3. Simple Aggregation at the DetNet layer
The resource control and management aspects of aggregation (including
the queuing/shaping/ policing implications) will be covered in other
documents.
The ability to aggregate individual flows, and their associated
resource control, into a larger aggregate is an important technique
for improving scaling of control in the data, management and control
planes. The DetNet data plane allows for the aggregation of DetNet
flows, to improved scaling. There are three methods of introducing
flow aggregation:
5.4.1. Aggregation at the LSP
DetNet flows forwarded via MPLS can leverage MPLS-TE's existing
support for hierarchical LSPs (H-LSPs), see [RFC4206]. H-LSPs are
typically used to aggregate control and resources, they may also be
used to provide OAM or protection for the aggregated LSPs. Arbitrary
levels of aggregation naturally falls out of the definition for
Varga, et al. Expires November 6, 2019 [Page 17]
Internet-Draft DetNet MPLS May 2019
hierarchy and the MPLS label stack [RFC3032]. DetNet nodes which
support aggregation (LSP hierarchy) map one or more LSPs (labels)
into and from an H-LSP. Both carried LSPs and H-LSPs may or may not
use the TC field, i.e., L-LSPs or E-LSPs. Such nodes will need to
ensure that traffic from aggregated LSPs are placed (shaped/policed/
enqueued) onto the H-LSPs in a fashion that ensures the required
DetNet service is preserved.
Additional details of the traffic control capabilities needed at a
DetNet-aware node may be covered in the new service descriptions
mentioned above or in separate future documents. Controller plane
mechanisms will also need to ensure that the service required on the
aggregate flow (H-LSP or DSCP) are provided, which may include the
discarding or remarking mentioned in the previous sections.
5.4.2. Aggregating DetNet Flows as a new DetNet flow
An aggregate can be built by layering DetNet flows as shown below:
+---------------------------------+
| |
| DetNet Flow |
| Payload Packet |
| |
+---------------------------------+ <--\
| DetNet Control Word | |
+=================================+ |
| S-Label | |
+---------------------------------+ +----DetNet data plane
| DetNet Control Word | | MPLS encapsulation
+=================================+ |
| A-Label | |
+---------------------------------+ |
| F-Label(s) | <--/
+---------------------------------+
| Data-Link |
+---------------------------------+
| Physical |
+---------------------------------+
Figure 6: DetNet Aggregation as a new DetNet Flow
Both the Aggregation (A) label and the S-Label have their MPLS S bit
set indicating bottom of stack, and the d-CW allows the PREOF to
work.
It is a property of the A-label that what follows is d-CW followed by
an S-Label. A relay node processing the A-label would not know the
Varga, et al. Expires November 6, 2019 [Page 18]
Internet-Draft DetNet MPLS May 2019
underlying payload type. This would only be known to a node that was
a peer of the node imposing the S-Label. However there is no real
need for it to know the payload type during aggregation processing.
5.4.3. Simple Aggregation at the DetNet Layer
Another approach would be not to include a d-CW for the aggregated
flow. This would be functionally similar to aggregation at the
forwarding sub-layer using H-LSPs, but would confine knowledge of the
aggregation to the DetNet layer. Such an approach shares the
disadvantage that PREOF operations would not be possible. OAM
operation in this mode is for further study.
+---------------------------------+
| |
| DetNet Flow |
| Payload Packet |
| |
+---------------------------------+ <--\
| DetNet Control Word | |
+=================================+ |
| S-Label | +----DetNet data plane
+---------------------------------+ | MPLS encapsulation
| A-Label | |
+---------------------------------+ |
| F-Label(s) | <--/
+---------------------------------+
| Data-Link |
+---------------------------------+
| Physical |
+---------------------------------+
Figure 7: Simple DetNet Aggregation
5.5. Service Sub-Layer Considerations
The edge and relay node internal procedures related to PREOF are
implementation specific. The order of a packet elimination or
replication is out of scope in this specification.
It is important that the DetNet layer is configured such that a
DetNet node never receives its own replicated packets. If it were to
receive such packets the replication function would make the loop
more destructive of bandwidth than a conventional unicast loop.
Ultimately the TTL in the S-Label will cause the packet to die during
a transient loop, but given the sensitivity of applications to packet
latency the impact on the DetNet application would be severe.
Varga, et al. Expires November 6, 2019 [Page 19]
Internet-Draft DetNet MPLS May 2019
5.5.1. Edge Node Processing
An edge node is responsible for matching ingress packets to the
service they require and encapsulating them accordingly. An edge
node may participate in the packet replication and duplicate packet
elimination.
The DetNet-aware forwarder selects the egress DetNet member flow
segment based on the flow identification. The mapping of ingress
DetNet member flow segment to egress DetNet member flow segment may
be statically or dynamically configured. Additionally the DetNet-
aware forwarder does duplicate frame elimination based on the flow
identification and the sequence number combination. The packet
replication is also done within the DetNet-aware forwarder. During
elimination and the replication process the sequence number of the
DetNet member flow MUST be preserved and copied to the egress DetNet
member flow.
The internal design of a relay node is out of scope of this document.
However the reader's attention is drawn to the need to make any PREOF
state available to the packet processor(s) dealing with packets to
which the PREOF functions must be applied, and to maintain that state
is such as way that it is available to the packet processor operation
on the next packet in the DetNet flow (which may be a duplicate, a
late packet, or the next packet in sequence.
5.5.2. Relay Node Processing
A DetNet Relay node operates in the DetNet forwarding sub-layer .
For DetNet using MPLS this processing is performed on the F-Label.
This processing is done within an extended forwarder function.
Whether an ingress DetNet member flow receives DetNet specific
processing depends on how the forwarding is programmed. Some relay
nodes may be DetNet service aware, while others may be unmodified
LSRs that only understand how to swicth MPLS-TE LSPs.
It is also possible to treat the relay node as a transit node, see
Section 5.4. Again, this is entirely up to how the forwarding has
been programmed.
5.6. Forwarding Sub-Layer Considerations
5.6.1. Class of Service
Class and quality of service, i.e., CoS and QoS, are terms that are
often used interchangeably and confused with each other. In the
context of DetNet, CoS is used to refer to mechanisms that provide
traffic forwarding treatment based on aggregate group basis and QoS
Varga, et al. Expires November 6, 2019 [Page 20]
Internet-Draft DetNet MPLS May 2019
is used to refer to mechanisms that provide traffic forwarding
treatment based on a specific DetNet flow basis. Examples of
existing network level CoS mechanisms include DiffServ which is
enabled by IP header differentiated services code point (DSCP) field
[RFC2474] and MPLS label traffic class field [RFC5462], and at Layer-
2, by IEEE 802.1p priority code point (PCP).
CoS for DetNet flows carried in PWs and MPLS is provided using the
existing MPLS Differentiated Services (DiffServ) architecture
[RFC3270]. Both E-LSP and L-LSP MPLS DiffServ modes MAY be used to
support DetNet flows. The Traffic Class field (formerly the EXP
field) of an MPLS label follows the definition of [RFC5462] and
[RFC3270]. The Uniform, Pipe, and Short Pipe DiffServ tunneling and
TTL processing models are described in [RFC3270] and [RFC3443] and
MAY be used for MPLS LSPs supporting DetNet flows. MPLS ECN MAY also
be used as defined in ECN [RFC5129] and updated by [RFC5462].
5.6.2. Quality of Service
In addition to explicit routes, and packet replication and
elimination, described in Section 5 above, DetNet provides zero
congestion loss and bounded latency and jitter. As described in
[I-D.ietf-detnet-architecture], there are different mechanisms that
maybe used separately or in combination to deliver a zero congestion
loss service. This includes Quality of Service (QoS) mechanisms at
the MPLS layer, that may be combined with the mechanisms defined by
the underlying network layer such as 802.1TSN.
Quality of Service (QoS) mechanisms for flow specific traffic
treatment typically includes a guarantee/agreement for the service,
and allocation of resources to support the service. Example QoS
mechanisms include discrete resource allocation, admission control,
flow identification and isolation, and sometimes path control,
traffic protection, shaping, policing and remarking. Example
protocols that support QoS control include Resource ReSerVation
Protocol (RSVP) [RFC2205] (RSVP) and RSVP-TE [RFC3209] and [RFC3473].
The existing MPLS mechanisms defined to support CoS [RFC3270] can
also be used to reserve resources for specific traffic classes.
A baseline set of QoS capabilities for DetNet flows carried in PWs
and MPLS can provided by MPLS with Traffic Engineering (MPLS-TE)
[RFC3209] and [RFC3473]. TE LSPs can also support explicit routes
(path pinning). Current service definitions for packet TE LSPs can
be found in "Specification of the Controlled Load Quality of
Service", [RFC2211], "Specification of Guaranteed Quality of
Service", [RFC2212], and "Ethernet Traffic Parameters", [RFC6003].
Additional service definitions are expected in future documents to
support the full range of DetNet services. In all cases, the
Varga, et al. Expires November 6, 2019 [Page 21]
Internet-Draft DetNet MPLS May 2019
existing label-based marking mechanisms defined for TE-LSPs and even
E-LSPs are use to support the identification of flows requiring
DetNet QoS.
6. Flow Identification Management and Control Information
[Editor's Note] The following will summarize the set of information
that is needed to support the MPLS DetNet data plane.
7. Security Considerations
The security considerations of DetNet in general are discussed in
[I-D.ietf-detnet-architecture] and [I-D.sdt-detnet-security]. Other
security considerations will be added in a future version of this
draft.
8. IANA Considerations
This document makes no IANA requests.
9. Contributors
RFC7322 limits the number of authors listed on the front page of a
draft to a maximum of 5, far fewer than the many individuals below
who made important contributions to this draft. The editor wishes to
thank and acknowledge each of the following authors for contributing
text to this draft. See also Section 10.
Loa Andersson
Huawei
Email: loa@pi.nu
Yuanlong Jiang
Huawei
Email: jiangyuanlong@huawei.com
Norman Finn
Huawei
3101 Rio Way
Spring Valley, CA 91977
USA
Email: norman.finn@mail01.huawei.com
Janos Farkas
Ericsson
Magyar Tudosok krt. 11.
Budapest 1117
Hungary
Varga, et al. Expires November 6, 2019 [Page 22]
Internet-Draft DetNet MPLS May 2019
Email: janos.farkas@ericsson.com
Carlos J. Bernardos
Universidad Carlos III de Madrid
Av. Universidad, 30
Leganes, Madrid 28911
Spain
Email: cjbc@it.uc3m.es
Tal Mizrahi
Marvell
6 Hamada st.
Yokneam
Israel
Email: talmi@marvell.com
Lou Berger
LabN Consulting, L.L.C.
Email: lberger@labn.net
Stewart Bryant
Huawei Technologies
Email: stewart.bryant@gmail.com
Mach Chen
Huawei Technologies
Email: mach.chen@huawei.com
Andrew G. Malis
Huawei Technologies
Email: agmalis@gmail.com
Don Fedyk
LabN Consulting, L.L.C.
Email: dfedyk@labn.net
10. Acknowledgements
The author(s) ACK and NACK.
The following people were part of the DetNet Data Plane Solution
Design Team:
Jouni Korhonen
Janos Farkas
Norman Finn
Varga, et al. Expires November 6, 2019 [Page 23]
Internet-Draft DetNet MPLS May 2019
Balazs Varga
Loa Andersson
Tal Mizrahi
David Mozes
Yuanlong Jiang
Andrew Malis
Carlos J. Bernardos
The DetNet chairs serving during the DetNet Data Plane Solution
Design Team:
Lou Berger
Pat Thaler
Thanks for Stewart Bryant for his extensive review of the previous
versions of the document.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2211] Wroclawski, J., "Specification of the Controlled-Load
Network Element Service", RFC 2211, DOI 10.17487/RFC2211,
September 1997, <https://www.rfc-editor.org/info/rfc2211>.
[RFC2212] Shenker, S., Partridge, C., and R. Guerin, "Specification
of Guaranteed Quality of Service", RFC 2212,
DOI 10.17487/RFC2212, September 1997,
<https://www.rfc-editor.org/info/rfc2212>.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031,
DOI 10.17487/RFC3031, January 2001,
<https://www.rfc-editor.org/info/rfc3031>.
Varga, et al. Expires November 6, 2019 [Page 24]
Internet-Draft DetNet MPLS May 2019
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001,
<https://www.rfc-editor.org/info/rfc3032>.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
<https://www.rfc-editor.org/info/rfc3209>.
[RFC3270] Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen,
P., Krishnan, R., Cheval, P., and J. Heinanen, "Multi-
Protocol Label Switching (MPLS) Support of Differentiated
Services", RFC 3270, DOI 10.17487/RFC3270, May 2002,
<https://www.rfc-editor.org/info/rfc3270>.
[RFC3443] Agarwal, P. and B. Akyol, "Time To Live (TTL) Processing
in Multi-Protocol Label Switching (MPLS) Networks",
RFC 3443, DOI 10.17487/RFC3443, January 2003,
<https://www.rfc-editor.org/info/rfc3443>.
[RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Resource ReserVation Protocol-
Traffic Engineering (RSVP-TE) Extensions", RFC 3473,
DOI 10.17487/RFC3473, January 2003,
<https://www.rfc-editor.org/info/rfc3473>.
[RFC4206] Kompella, K. and Y. Rekhter, "Label Switched Paths (LSP)
Hierarchy with Generalized Multi-Protocol Label Switching
(GMPLS) Traffic Engineering (TE)", RFC 4206,
DOI 10.17487/RFC4206, October 2005,
<https://www.rfc-editor.org/info/rfc4206>.
[RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson,
"Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for
Use over an MPLS PSN", RFC 4385, DOI 10.17487/RFC4385,
February 2006, <https://www.rfc-editor.org/info/rfc4385>.
[RFC5085] Nadeau, T., Ed. and C. Pignataro, Ed., "Pseudowire Virtual
Circuit Connectivity Verification (VCCV): A Control
Channel for Pseudowires", RFC 5085, DOI 10.17487/RFC5085,
December 2007, <https://www.rfc-editor.org/info/rfc5085>.
[RFC5129] Davie, B., Briscoe, B., and J. Tay, "Explicit Congestion
Marking in MPLS", RFC 5129, DOI 10.17487/RFC5129, January
2008, <https://www.rfc-editor.org/info/rfc5129>.
Varga, et al. Expires November 6, 2019 [Page 25]
Internet-Draft DetNet MPLS May 2019
[RFC5462] Andersson, L. and R. Asati, "Multiprotocol Label Switching
(MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic
Class" Field", RFC 5462, DOI 10.17487/RFC5462, February
2009, <https://www.rfc-editor.org/info/rfc5462>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
11.2. Informative References
[I-D.ietf-detnet-architecture]
Finn, N., Thubert, P., Varga, B., and J. Farkas,
"Deterministic Networking Architecture", draft-ietf-
detnet-architecture-12 (work in progress), March 2019.
[I-D.ietf-detnet-data-plane-framework]
Korhonen, J., Varga, B., "DetNet Data Plane Framework",
2019.
[I-D.ietf-detnet-mpls-over-tsn]
Korhonen, J., Varga, B., "DetNet MPLS over IEEE 802.1 TSN
Sub-Networks", 2019.
[I-D.ietf-spring-segment-routing-mpls]
Bashandy, A., Filsfils, C., Previdi, S., Decraene, B.,
Litkowski, S., and R. Shakir, "Segment Routing with MPLS
data plane", draft-ietf-spring-segment-routing-mpls-22
(work in progress), May 2019.
[I-D.sdt-detnet-security]
Mizrahi, T., Grossman, E., Hacker, A., Das, S.,
"Deterministic Networking (DetNet) Security
Considerations, draft-sdt-detnet-security, work in
progress", 2017.
[RFC2205] Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S.
Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
Functional Specification", RFC 2205, DOI 10.17487/RFC2205,
September 1997, <https://www.rfc-editor.org/info/rfc2205>.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
DOI 10.17487/RFC2474, December 1998,
<https://www.rfc-editor.org/info/rfc2474>.
Varga, et al. Expires November 6, 2019 [Page 26]
Internet-Draft DetNet MPLS May 2019
[RFC3272] Awduche, D., Chiu, A., Elwalid, A., Widjaja, I., and X.
Xiao, "Overview and Principles of Internet Traffic
Engineering", RFC 3272, DOI 10.17487/RFC3272, May 2002,
<https://www.rfc-editor.org/info/rfc3272>.
[RFC3985] Bryant, S., Ed. and P. Pate, Ed., "Pseudo Wire Emulation
Edge-to-Edge (PWE3) Architecture", RFC 3985,
DOI 10.17487/RFC3985, March 2005,
<https://www.rfc-editor.org/info/rfc3985>.
[RFC4448] Martini, L., Ed., Rosen, E., El-Aawar, N., and G. Heron,
"Encapsulation Methods for Transport of Ethernet over MPLS
Networks", RFC 4448, DOI 10.17487/RFC4448, April 2006,
<https://www.rfc-editor.org/info/rfc4448>.
[RFC4875] Aggarwal, R., Ed., Papadimitriou, D., Ed., and S.
Yasukawa, Ed., "Extensions to Resource Reservation
Protocol - Traffic Engineering (RSVP-TE) for Point-to-
Multipoint TE Label Switched Paths (LSPs)", RFC 4875,
DOI 10.17487/RFC4875, May 2007,
<https://www.rfc-editor.org/info/rfc4875>.
[RFC5440] Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
Element (PCE) Communication Protocol (PCEP)", RFC 5440,
DOI 10.17487/RFC5440, March 2009,
<https://www.rfc-editor.org/info/rfc5440>.
[RFC5586] Bocci, M., Ed., Vigoureux, M., Ed., and S. Bryant, Ed.,
"MPLS Generic Associated Channel", RFC 5586,
DOI 10.17487/RFC5586, June 2009,
<https://www.rfc-editor.org/info/rfc5586>.
[RFC5921] Bocci, M., Ed., Bryant, S., Ed., Frost, D., Ed., Levrau,
L., and L. Berger, "A Framework for MPLS in Transport
Networks", RFC 5921, DOI 10.17487/RFC5921, July 2010,
<https://www.rfc-editor.org/info/rfc5921>.
[RFC6003] Papadimitriou, D., "Ethernet Traffic Parameters",
RFC 6003, DOI 10.17487/RFC6003, October 2010,
<https://www.rfc-editor.org/info/rfc6003>.
[RFC6006] Zhao, Q., Ed., King, D., Ed., Verhaeghe, F., Takeda, T.,
Ali, Z., and J. Meuric, "Extensions to the Path
Computation Element Communication Protocol (PCEP) for
Point-to-Multipoint Traffic Engineering Label Switched
Paths", RFC 6006, DOI 10.17487/RFC6006, September 2010,
<https://www.rfc-editor.org/info/rfc6006>.
Varga, et al. Expires November 6, 2019 [Page 27]
Internet-Draft DetNet MPLS May 2019
[RFC6073] Martini, L., Metz, C., Nadeau, T., Bocci, M., and M.
Aissaoui, "Segmented Pseudowire", RFC 6073,
DOI 10.17487/RFC6073, January 2011,
<https://www.rfc-editor.org/info/rfc6073>.
[RFC6790] Kompella, K., Drake, J., Amante, S., Henderickx, W., and
L. Yong, "The Use of Entropy Labels in MPLS Forwarding",
RFC 6790, DOI 10.17487/RFC6790, November 2012,
<https://www.rfc-editor.org/info/rfc6790>.
Authors' Addresses
Balazs Varga (editor)
Ericsson
Magyar Tudosok krt. 11.
Budapest 1117
Hungary
Email: balazs.a.varga@ericsson.com
Janos Farkas
Ericsson
Magyar Tudosok krt. 11.
Budapest 1117
Hungary
Email: janos.farkas@ericsson.com
Lou Berger
LabN Consulting, L.L.C.
Email: lberger@labn.net
Don Fedyk
LabN Consulting, L.L.C.
Email: dfedyk@labn.net
Andrew G. Malis
Huawei Technologies
Email: agmalis@gmail.com
Varga, et al. Expires November 6, 2019 [Page 28]
Internet-Draft DetNet MPLS May 2019
Stewart Bryant
Huawei Technologies
Email: stewart.bryant@gmail.com
Jouni Korhonen
Email: jouni.nospam@gmail.com
Varga, et al. Expires November 6, 2019 [Page 29]