Skip to main content

DHCPv6 Options for Network Boot
draft-ietf-dhc-dhcpv6-opt-netboot-10

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 5970.
Authors Dave Thaler , Thomas Huth , Jens Freimann , Vincent Zimmer
Last updated 2015-10-14 (Latest revision 2010-07-26)
RFC stream Internet Engineering Task Force (IETF)
Intended RFC status Proposed Standard
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state (None)
Document shepherd (None)
IESG IESG state Became RFC 5970 (Proposed Standard)
Action Holders
(None)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD Ralph Droms
Send notices to (None)
draft-ietf-dhc-dhcpv6-opt-netboot-10
DHC                                                              T. Huth
Internet-Draft                                               J. Freimann
Intended status: Standards Track                  IBM Germany Research &
Expires: January 27, 2011                               Development GmbH
                                                               V. Zimmer
                                                                   Intel
                                                               D. Thaler
                                                               Microsoft
                                                           July 26, 2010

                    DHCPv6 options for network boot
                  draft-ietf-dhc-dhcpv6-opt-netboot-10

Abstract

   The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) provides a
   framework for passing configuration information to nodes on a
   network.  This document describes new options for DHCPv6 which SHOULD
   be used for booting a node from the network.

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on January 27, 2011.

Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

Huth, et al.            Expires January 27, 2011                [Page 1]
Internet-Draft       DHCPv6 options for network boot           July 2010

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Conventions  . . . . . . . . . . . . . . . . . . . . . . . . .  4
   3.  Options  . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
     3.1.  Boot File Uniform Resource Locator (URL) Option  . . . . .  4
     3.2.  Boot File Parameters Option  . . . . . . . . . . . . . . .  5
     3.3.  Client System Architecture Type Option . . . . . . . . . .  6
     3.4.  Client Network Interface Identifier Option . . . . . . . .  7
   4.  Appearance of the options  . . . . . . . . . . . . . . . . . .  7
   5.  Download protocol considerations . . . . . . . . . . . . . . .  7
   6.  IANA considerations  . . . . . . . . . . . . . . . . . . . . .  8
   7.  Security considerations  . . . . . . . . . . . . . . . . . . .  8
   8.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . .  9
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . .  9
     9.1.  Normative References . . . . . . . . . . . . . . . . . . .  9
     9.2.  Informative References . . . . . . . . . . . . . . . . . . 10
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 10

Huth, et al.            Expires January 27, 2011                [Page 2]
Internet-Draft       DHCPv6 options for network boot           July 2010

1.  Introduction

   This draft describes DHCPv6 options that SHOULD be used to provide
   configuration information for a node that must be booted using the
   network, rather than from local storage.

   Network booting is used, for example, in some environments where
   administrators have to maintain a large number of nodes.  By serving
   all boot and configuration files from a central server, the effort
   required to maintain these nodes is greatly reduced.

   A typical boot file would be, for example, an operating system kernel
   or a boot loader program.  To be able to execute such a file, the
   firmware running on the client node must perform the following two
   steps (see Figure 1): First get all information which is required for
   downloading and executing the boot file.  Second, download the boot
   file and execute it.

                                            +------+
                    _______________________\| DHCP |
                   / 1 Get boot file info  /|Server|
           +------+                         +------+
           | Host |
           +------+                         +------+
                   \_______________________\| File |
                     2 Download boot file  /|Server|
                                            +------+

                      Figure 1: Network Boot Sequence

   The information which is required for booting over the network MUST
   include at least the details about the server on which the boot files
   can be found, the protocol to be used for the download (for example
   HTTP [RFC2616] or TFTP [RFC1350]) and the path and name of the boot
   file on the server.  Additionally, the server and client MAY exchange
   information about the parameters which should be passed to the OS
   kernel or boot loader program respectively, or information about the
   supported boot environment.

   DHCPv6 allows client nodes to ask a DHCPv6 server for configuration
   parameters.  This document provides new options which a client can
   request from the DHCPv6 server to satisfy its requirements for
   booting.  It also introduces a new IANA registry for processor
   architecture types which are used by the OPTION_CLIENT_ARCH_TYPE
   option (see Section 3.3).

Huth, et al.            Expires January 27, 2011                [Page 3]
Internet-Draft       DHCPv6 options for network boot           July 2010

2.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

   Terminology specific to IPv6 and DHCPv6 are used in the same way as
   defined in the "Terminology" sections of [RFC3315].

3.  Options

   Option formats comply with DHCPv6 options per [RFC3315] (section 6).
   The boot-file-url option (see Section 3.1) is mandatory for booting,
   all other options are optional.

3.1.  Boot File Uniform Resource Locator (URL) Option

   The server sends this option to inform the client about an URL to a
   boot file.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       OPT_BOOTFILE_URL        |            option-len         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   .                  boot-file-url (variable length)              .
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Format description:

   option-code       OPT_BOOTFILE_URL (TBD1).

   option-len        Length of the boot-file-url in octets.

   boot-file-url     This string is the URL for the boot file.  It MUST
                     comply with STD 66 [RFC3986].  The string is not
                     NUL-terminated.

   If the host in the URL is expressed using an IPv6 address rather than
   a domain name, the address in the URL then MUST be enclosed in "["
   and "]" characters, conforming to [RFC3986].  Clients that have DNS
   implementations SHOULD support the use of domain names in the URL.

Huth, et al.            Expires January 27, 2011                [Page 4]
Internet-Draft       DHCPv6 options for network boot           July 2010

3.2.  Boot File Parameters Option

   This option is sent by the server to the client.  It consists of
   multiple UTF-8 ([RFC3629]) strings.  They are used to specify
   parameters for the boot file (similar to the command line arguments
   in most modern operating systems).  For example, these parameters
   could be used to specify the root file system of the OS kernel, or
   where a second stage boot loader can download its configuration file
   from.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       OPT_BOOTFILE_PARAM      |            option-len         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | param-len 1                   |                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+           parameter 1         .
   .                                        (variable length)      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   .                                                               .
   .                       <multiple Parameters>                   .
   .                                                               .
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | param-len n                   |                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+           parameter n         .
   .                                        (variable length)      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Format description:

   option-code       OPT_BOOTFILE_PARAM (TBD2).

   option-len        Length of the Boot File Parameters option in octets
                     (not including the size of the option-code and
                     option-len fields).

   param-len 1...n   This is a 16-bit integer which specifies the length
                     of the following parameter in octets (not including
                     the parameter-length field).

   parameter 1...n   These UTF-8 strings are parameters needed for
                     booting, e.g. kernel parameters.  The strings are
                     not NUL-terminated.

   When the boot firmware executes the boot file which has been
   specified in the OPT_BOOTFILE_URL option, it MUST pass these
   parameters, if present, in the order that they appear in the

Huth, et al.            Expires January 27, 2011                [Page 5]
Internet-Draft       DHCPv6 options for network boot           July 2010

   OPT_BOOTFILE_PARAM option.

3.3.  Client System Architecture Type Option

   This option provides parity with the Client System Architecture Type
   Option defined for DHCPv4 in section 2.1 of [RFC4578].

   The format of the option is:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    OPTION_CLIENT_ARCH_TYPE    |         option-len            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   .                                                               .
   .             architecture-types (variable length)              .
   .                                                               .
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   option-code         OPTION_CLIENT_ARCH_TYPE (TBD3).

   option-len          Length of the "architecture-types" field in
                       octets.  It MUST be an even number greater than
                       zero.  See section 2.1 of [RFC4578] for details.

   architecture-types  A list of one or more architecture types, as
                       specified in section 2.1 of [RFC4578].  Each
                       architecture type identifier in this list is a
                       16-bit value which describes the pre-boot runtime
                       environment of the client machine.  A list of
                       valid values is maintained by the IANA (see
                       Section 6).

   The client MAY use this option to send a list of supported
   architecture types to the server, so the server can decide which boot
   file should be provided to the client.  If a client supports more
   than one pre-boot environment (for example both, 32-bit and 64-bit
   executables), the most preferred architecture type MUST be listed as
   first item, followed by the others with descending priority.

   If the client used this option in the request, the server SHOULD
   include this option to inform the client about the pre-boot
   environments which are supported by the boot file.  The list MUST
   only contain architecture types which have initially been queried by
   the client.  The items MUST also be listed in order of descending
   priority.

Huth, et al.            Expires January 27, 2011                [Page 6]
Internet-Draft       DHCPv6 options for network boot           July 2010

3.4.  Client Network Interface Identifier Option

   If the client supports the Universal Network Device Interface (UNDI)
   (see [PXE21] and [UEFI23]), it may send the Client Network Interface
   Identifier option to a DHCP server to provide information about its
   level of UNDI support.

   This option provides parity with the Client Network Interface
   Identifier Option defined for DHCPv4 in section 2.2 of [RFC4578].

   The format of the option is:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           OPTION_NII          |          option-len           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |     Major     |      Minor      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   option-code       OPTION_NII (TBD4).

   option-len        3

   Type              As specified in section 2.2 of [RFC4578].

   Major             As specified in section 2.2 of [RFC4578].

   Minor             As specified in section 2.2 of [RFC4578].

   The list of valid Type, Major and Minor values is maintained in the
   Unified Extensible Firmware Interface specification [UEFI23].

4.  Appearance of the options

   These options MUST NOT appear in DHCPv6 messages other than the types
   Solicit, Advertise, Request, Renew, Rebind, Information-Request and
   Reply.

   The option-codes of these options MAY appear in the Option Request
   Option in the DHCPv6 message types Solicit, Request, Renew, Rebind,
   Information-Request and Reconfigure.

5.  Download protocol considerations

   The Boot File URL option does not place any constraints on the

Huth, et al.            Expires January 27, 2011                [Page 7]
Internet-Draft       DHCPv6 options for network boot           July 2010

   protocol used for downloading the boot file, other than that it MUST
   be possible to specify it in a URL.  For the sake of administrative
   simplicity, we strongly recommend that, at a mininum, implementors of
   network boot loaders implement the well-known and established
   hypertext transfer protocol [RFC2616] for downloading.  Please note
   that for IPv6, this supersedes [RFC906] which recommended to use TFTP
   for downloading (see [RFC3617] for the 'tftp' URL definition).

   When using iSCSI for booting, the 'iscsi' URI is formed as defined in
   [RFC4173].  The functionality attributed in RFC4173 to a root path
   option is provided for IPv6 by the Boot File URL option instead.

6.  IANA considerations

   The following options need to be assigned by the IANA from the option
   number space defined in the chapter 24 of the DHCPv6 RFC [RFC3315].

            +-------------------------+-------+--------------+
            |       Option name       | Value | Specified in |
            +-------------------------+-------+--------------+
            |     OPT_BOOTFILE_URL    |  TBD1 |  Section 3.1 |
            |    OPT_BOOTFILE_PARAM   |  TBD2 |  Section 3.2 |
            | OPTION_CLIENT_ARCH_TYPE |  TBD3 |  Section 3.3 |
            |        OPTION_NII       |  TBD4 |  Section 3.4 |
            +-------------------------+-------+--------------+

   This document also introduces a new IANA registry for processor
   architecture types.  The name of this registry shall be "Processor
   Architecture Type".  Registry entries consist of a 16-bit integer
   recorded in decimal format, and a descriptive name.  The initial
   values of this registry can be found in [RFC4578] section 2.1.

   The assignment policy for values shall be Expert Review (see
   [RFC5226]), and any requests for values must supply the descriptive
   name for the processor architecture type.

7.  Security considerations

   In untrusted networks, a rogue DHCPv6 server could send the new
   DHCPv6 options described in this document.  The booting clients could
   then be provided with a wrong URL so that either the boot fails, or
   even worse, the client boots the wrong operating system which has
   been provided by a malicious file server.  To prevent this kind of
   attack, clients SHOULD use authentication of DHCPv6 messages (see
   chapter 21. in [RFC3315]).

Huth, et al.            Expires January 27, 2011                [Page 8]
Internet-Draft       DHCPv6 options for network boot           July 2010

   Note also that DHCPv6 messages are sent unencrypted by default.  So
   the boot file URL options are sent unencrypted over the network, too.
   This can become a security risk since the URLs can contain sensitive
   information like user names and passwords (for example a URL like
   "ftp://username:password@servername/path/file").  At the current
   point in time, there is no possibility to send encrypted DHCPv6
   messages, so it is strongly RECOMMENDED not to use sensitive
   information in the URLs in untrusted networks (using passwords in
   URLs is deprecated anyway according to [RFC3986]).

   Even if the DHCPv6 transaction is secured, this does not protect
   against attacks on the boot file download channel.  Consequently, we
   recommend that either protocols like HTTPS [RFC2818] or TLS within
   HTTP [RFC2817] are used to prevent spoofing, or that the boot loader
   software implements a mechanism for signing boot images and a
   configurable signing key in memory, so that if a malicious image is
   provided, it can be detected and rejected.

8.  Acknowledgements

   The authors would like to thank Ruth Li, Dong Wei, Kathryn Hampton,
   Phil Dorah, Richard Chan, and Fiona Jensen for discussions that led
   to this document.

   The authors would also like to thank Ketan P. Pancholi, Alfred
   Hoenes, Gabriel Montenegro and Ted Lemon for corrections and
   suggestions.

9.  References

9.1.  Normative References

   [PXE21]    Johnston, M., "Preboot Execution Environment (PXE)
              Specification", September 1999,
              <http://www.pix.net/software/pxeboot/archive/pxespec.pdf>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3315]  Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
              and M. Carney, "Dynamic Host Configuration Protocol for
              IPv6 (DHCPv6)", RFC 3315, July 2003.

   [RFC3629]  Yergeau, F., "UTF-8, a transformation format of ISO
              10646", STD 63, RFC 3629, November 2003.

Huth, et al.            Expires January 27, 2011                [Page 9]
Internet-Draft       DHCPv6 options for network boot           July 2010

   [RFC3986]  Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
              Resource Identifier (URI): Generic Syntax", STD 66,
              RFC 3986, January 2005.

   [RFC4173]  Sarkar, P., Missimer, D., and C. Sapuntzakis,
              "Bootstrapping Clients using the Internet Small Computer
              System Interface (iSCSI) Protocol", RFC 4173,
              September 2005.

   [RFC4578]  Johnston, M. and S. Venaas, "Dynamic Host Configuration
              Protocol (DHCP) Options for the Intel Preboot eXecution
              Environment (PXE)", RFC 4578, November 2006.

   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              May 2008.

   [UEFI23]   UEFI Forum, "Unified Extensible Firmware Interface
              Specification, Version 2.3", May 2009,
              <http://www.uefi.org/>.

9.2.  Informative References

   [RFC1350]  Sollins, K., "The TFTP Protocol (Revision 2)", STD 33,
              RFC 1350, July 1992.

   [RFC2616]  Fielding, R., Gettys, J., Mogul, J., Frystyk, H.,
              Masinter, L., Leach, P., and T. Berners-Lee, "Hypertext
              Transfer Protocol -- HTTP/1.1", RFC 2616, June 1999.

   [RFC2817]  Khare, R. and S. Lawrence, "Upgrading to TLS Within
              HTTP/1.1", RFC 2817, May 2000.

   [RFC2818]  Rescorla, E., "HTTP Over TLS", RFC 2818, May 2000.

   [RFC3617]  Lear, E., "Uniform Resource Identifier (URI) Scheme and
              Applicability Statement for the Trivial File Transfer
              Protocol (TFTP)", RFC 3617, October 2003.

   [RFC906]   Finlayson, R., "Bootstrap Loading using TFTP", RFC 906,
              June 1984.

Huth, et al.            Expires January 27, 2011               [Page 10]
Internet-Draft       DHCPv6 options for network boot           July 2010

Authors' Addresses

   Thomas H. Huth
   IBM Germany Research & Development GmbH
   Schoenaicher Strasse 220
   Boeblingen  71032
   Germany

   Phone: +49-7031-16-2183
   Email: thuth@de.ibm.com

   Jens T. Freimann
   IBM Germany Research & Development GmbH
   Schoenaicher Strasse 220
   Boeblingen  71032
   Germany

   Phone: +49-7031-16-1122
   Email: jfrei@de.ibm.com

   Vincent Zimmer
   Intel
   2800 Center Drive
   DuPont  WA 98327
   USA

   Phone: +1 253 371 5667
   Email: vincent.zimmer@intel.com

   Dave Thaler
   Microsoft
   One Microsoft Way
   Redmond  WA 98052
   USA

   Phone: +1 425 703-8835
   Email: dthaler@microsoft.com

Huth, et al.            Expires January 27, 2011               [Page 11]