Skip to main content

Client Subnet in DNS Queries

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 7871.
Authors Carlo Contavalli , Wilmer van der Gaast , David C Lawrence , Warren "Ace" Kumari
Last updated 2016-01-21 (Latest revision 2015-12-15)
Replaces draft-vandergaast-edns-client-subnet
RFC stream Internet Engineering Task Force (IETF)
Additional resources Mailing list discussion
Stream WG state Submitted to IESG for Publication
Document shepherd Suzanne Woolf
Shepherd write-up Show Last changed 2015-12-30
IESG IESG state IESG Evaluation::Revised I-D Needed
Consensus boilerplate Yes
Telechat date (None)
Needs a YES.
Responsible AD Joel Jaeggli
Send notices to "Suzanne Woolf" <>
IANA IANA review state IANA OK - Actions Needed
dnsop                                                      C. Contavalli
Internet-Draft                                          W. van der Gaast
Intended status: Informational                                    Google
Expires: June 17, 2016                                       D. Lawrence
                                                     Akamai Technologies
                                                               W. Kumari
                                                       December 15, 2015

                      Client Subnet in DNS Queries


   This document defines an EDNS0 extension to carry information about
   the network that originated a DNS query, and the network for which
   the subsequent response can be cached.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on June 17, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   ( in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of

Contavalli, et al.        Expires June 17, 2016                 [Page 1]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Privacy Note  . . . . . . . . . . . . . . . . . . . . . . . .   4
   3.  Requirements Notation . . . . . . . . . . . . . . . . . . . .   4
   4.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
   5.  Overview  . . . . . . . . . . . . . . . . . . . . . . . . . .   5
   6.  Option Format . . . . . . . . . . . . . . . . . . . . . . . .   6
   7.  Protocol Description  . . . . . . . . . . . . . . . . . . . .   8
     7.1.  Originating the Option  . . . . . . . . . . . . . . . . .   8
       7.1.1.  Recursive Resolvers . . . . . . . . . . . . . . . . .   8
       7.1.2.  Stub Resolvers  . . . . . . . . . . . . . . . . . . .   9
       7.1.3.  Forwarding Resolvers  . . . . . . . . . . . . . . . .   9
     7.2.  Generating a Response . . . . . . . . . . . . . . . . . .  10
       7.2.1.  Authoritative Nameserver  . . . . . . . . . . . . . .  10
       7.2.2.  Intermediate Nameserver . . . . . . . . . . . . . . .  12
     7.3.  Handling ECS Responses and Caching  . . . . . . . . . . .  12
       7.3.1.  Caching the Response  . . . . . . . . . . . . . . . .  13
       7.3.2.  Answering from Cache  . . . . . . . . . . . . . . . .  13
     7.4.  Delegations and Negative Answers  . . . . . . . . . . . .  14
     7.5.  Transitivity  . . . . . . . . . . . . . . . . . . . . . .  15
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  15
   9.  DNSSEC Considerations . . . . . . . . . . . . . . . . . . . .  16
   10. NAT Considerations  . . . . . . . . . . . . . . . . . . . . .  16
   11. Security Considerations . . . . . . . . . . . . . . . . . . .  17
     11.1.  Privacy  . . . . . . . . . . . . . . . . . . . . . . . .  17
     11.2.  Birthday Attacks . . . . . . . . . . . . . . . . . . . .  17
     11.3.  Cache Pollution  . . . . . . . . . . . . . . . . . . . .  18
   12. Sending the Option  . . . . . . . . . . . . . . . . . . . . .  19
     12.1.  Probing  . . . . . . . . . . . . . . . . . . . . . . . .  19
     12.2.  Whitelist  . . . . . . . . . . . . . . . . . . . . . . .  20
   13. Example . . . . . . . . . . . . . . . . . . . . . . . . . . .  21
   14. Contributing Authors  . . . . . . . . . . . . . . . . . . . .  22
   15. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  23
   16. References  . . . . . . . . . . . . . . . . . . . . . . . . .  23
     16.1.  Normative References . . . . . . . . . . . . . . . . . .  23
     16.2.  Informative References . . . . . . . . . . . . . . . . .  24
   Appendix A.  Document History . . . . . . . . . . . . . . . . . .  25
     A.1.  -00 . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
     A.2.  -01 . . . . . . . . . . . . . . . . . . . . . . . . . . .  28
     A.3.  -02 . . . . . . . . . . . . . . . . . . . . . . . . . . .  29
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  29

Contavalli, et al.        Expires June 17, 2016                 [Page 2]
Internet-Draft        Client Subnet in DNS Queries         December 2015

1.  Introduction

   Many Authoritative Nameservers today return different responses based
   on the perceived topological location of the user.  These servers use
   the IP address of the incoming query to identify that location.
   Since most queries come from intermediate Recursive Resolvers, the
   source address is that of the Recursive Resolver rather than of the
   query originator.

   Traditionally, and probably still in the majority of instances,
   Recursive Resolvers are reasonably close in the topological sense to
   the Stub Resolvers or Forwarding Resolvers that are the source of
   queries.  For these resolvers, using their own IP address is
   sufficient for authority servers that tailor responses based upon
   location of the querier.

   Increasingly, though, a class of Recursive Resolvers has arisen that
   handle query sources that are often not topologically close.  The
   motivation for a user to configure such a Centralized Resolver varies
   but is usually because of some enhanced experience, such as greater
   cache security or applying policies regarding where users may
   connect.  (Although political censorship usually comes to mind here,
   the same actions may be used by a parent when setting controls on
   where a minor may connect.)  Similarly, many ISPs and other
   organizations use a Centralized Resolver infrastructure that can be
   distant from the clients the resolvers serve.  These cases all lead
   to less than desirable responses from topology-sensitive
   Authoritative Nameservers.

   This document defines an EDNS0 [RFC6891] option to convey network
   information that is relevant to the DNS message.  It will carry
   sufficient network information about the originator for the
   Authoritative Nameserver to tailor responses.  It will also provide
   for the Authoritative Nameserver to indicate the scope of network
   addresses for which the tailored answer is intended.  This EDNS0
   option is intended for those recursive and authority servers that
   would benefit from the extension and not for general purpose
   deployment.  It is completely optional and can safely be ignored by
   servers that choose not to implement it or enable it.

   This document also includes guidelines on how to best cache those
   results and provides recommendations on when this protocol extension
   should be used.

   At least a dozen different client and server implementations have
   been written based on earlier versions of this specification.  The
   protocol is in active production use today.  While the
   implementations interoperate, there is varying behavior around edge

Contavalli, et al.        Expires June 17, 2016                 [Page 3]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   cases that were poorly specified.  Known incompatibilities are
   described in this document, and the authors believe that it is better
   to describe the system as it is working today, even if not everyone
   agrees with the details of the original specification (
   [I-D.vandergaast-edns-client-subnet]).  The alternative is an
   undocumented and proprietary system.

   A revised proposal to improve upon the minor flaws in this protocol
   will be forthcoming to the IETF.

2.  Privacy Note

   If we were just beginning to design this mechanism, and not
   documenting existing protocol, it is unlikely that we would have done
   things exactly this way.

   The IETF is actively working on enhancing DNS privacy
   [DPRIVE_Working_Group], and the re-injection of metadata has been
   identified as a problematic design pattern

   As noted above, however, this document primarily describes existing
   behavior of a deployed method, to further the understanding of the
   Internet community.

   We encourage the deployment of means to allow users to make use of
   the opt-out provided.  We also recommend that others avoid techniques
   that may introduce additional metadata in future work, as it may
   damage user trust.

3.  Requirements Notation

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   document are to be interpreted as described in [RFC2119].

4.  Terminology

   ECS:  EDNS Client Subnet.

   Client:  A Stub Resolver, Forwarding Resolver, or Recursive Resolver.
      A client to a Recursive Resolver or a Forwarding Resolver.

   Server:  A Forwarding Resolver, Recursive Resolver or Authoritative

Contavalli, et al.        Expires June 17, 2016                 [Page 4]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   Stub Resolver:  A simple DNS protocol implementation on the client
      side as described in [RFC1034] section 5.3.1.  A client to a
      Recursive Resolver or a Forwarding Resolver.

   Authoritative Nameserver:  A nameserver that has authority over one
      or more DNS zones.  These are normally not contacted by Stub
      Resolver or end user clients directly but by Recursive Resolvers.
      Described in [RFC1035] Section 6.

   Recursive Resolver:  A nameserver that is responsible for resolving
      domain names for clients by following the domain's delegation
      chain.  Recursive Resolvers frequently use caches to be able to
      respond to client queries quickly.  Described in [RFC1035]
      Section 7.

   Forwarding Resolver:  A nameserver that does not do iterative
      resolution itself, but instead passes that responsibility to
      another Recursive Resolver, called a "Forwarder" in [RFC2308]
      section 1.

   Intermediate Nameserver:  Any nameserver in between the Stub Resolver
      and the Authoritative Nameserver, such as a Recursive Resolver or
      a Forwarding Resolver.

   Centralized Resolvers:  Intermediate Nameservers that serve a
      topologically diverse network address space.

   Tailored Response:  A response from a nameserver that is customized
      for the node that sent the query, often based on performance (i.e.
      lowest latency, least number of hops, topological distance, ...).

   Topologically Close:  Refers to two hosts being close in terms of
      number of hops or time it takes for a packet to travel from one
      host to the other.  The concept of topological distance is only
      loosely related to the concept of geographical distance: two
      geographically close hosts can still be very distant from a
      topological perspective, and two geographically distant hosts can
      be quite close on the network.

5.  Overview

   The general idea of this document is to provide an EDNS0 option to
   allow Recursive Resolvers, if they are willing, to forward details
   about the origin network from which a query is coming when talking to
   other Nameservers.

   The format of this option is described in Section 6, and is meant to
   be added in queries sent by Intermediate Nameservers in a way

Contavalli, et al.        Expires June 17, 2016                 [Page 5]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   transparent to Stub Resolvers and end users, as described in
   Section 7.1.  ECS is only defined for the Internet (IN) DNS class.

   As described in Section 7.2, an Authoritative Nameserver could use
   this EDNS0 option as a hint to better locate the network of the end
   user and provide a better answer.

   Its response would contain an edns-client-subnet (ECS) option,
   clearly indicating that the server made use of this information, and
   that the answer is tied to the network of the client.

   As described in Section 7.3, Intermediate Nameservers would use this
   information to cache the response.

   Some Intermediate Nameservers may also have to be able to forward ECS
   queries they receive.  This is described in Section 7.5.

   The mechanisms provided by ECS raise various security related
   concerns related to cache growth, the ability to spoof EDNS0 options,
   and privacy.  Section 11 explores various mitigation techniques.

   The expectation, however, is that this option will primarily be used
   between Recursive Resolvers and Authoritative Nameservers that are
   sensitive to network location issues.  Most Recursive Resolvers,
   Authoritative Nameservers and Stub Resolvers will never need to know
   about this option, and will continue working as they had been.

   Failure to support this option or its improper handling will, at
   worst, cause suboptimal identification of client location, which is a
   common occurrence in current content delivery network (CDN) setups.

   Section 7.1 also provides a mechanism for Stub Resolvers to signal
   Recursive Resolvers that they do not want ECS treatment for specific

   Additionally, operators of Intermediate Nameservers with ECS enabled
   are allowed to choose how many bits of the address of received
   queries to forward, or to reduce the number of bits forwarded for
   queries already including an ECS option.

6.  Option Format

   This protocol uses an EDNS0 [RFC6891]) option to include client
   address information in DNS messages.  The option is structured as

Contavalli, et al.        Expires June 17, 2016                 [Page 6]
Internet-Draft        Client Subnet in DNS Queries         December 2015

                +0 (MSB)                            +1 (LSB)
   0: |                          OPTION-CODE                          |
   2: |                         OPTION-LENGTH                         |
   4: |                            FAMILY                             |
   6: |     SOURCE PREFIX-LENGTH      |     SCOPE PREFIX-LENGTH       |
   8: |                           ADDRESS...                          /

   o  (Defined in [RFC6891]) OPTION-CODE, 2 octets, for ECS is 8 (0x00

   o  (Defined in [RFC6891]) OPTION-LENGTH, 2 octets, contains the
      length of the payload (everything after OPTION-LENGTH) in octets.

   o  FAMILY, 2 octets, indicates the family of the address contained in
      the option, using address family codes as assigned by IANA in
      Address Family Numbers [Address_Family_Numbers].

   The format of the address part depends on the value of FAMILY.  This
   document only defines the format for FAMILY 1 (IP version 4) and 2
   (IP version 6), which are as follows:

   o  SOURCE PREFIX-LENGTH, an unsigned octet representing the leftmost
      number of significant bits of ADDRESS to be used for the lookup.
      In responses, it mirrors the same value as in the queries.

   o  SCOPE PREFIX-LENGTH, an unsigned octet representing the leftmost
      number of significant bits of ADDRESS that the response covers.
      In queries, it MUST be set to 0.

   o  ADDRESS, variable number of octets, contains either an IPv4 or
      IPv6 address, depending on FAMILY, which MUST be truncated to the
      number of bits indicated by the SOURCE PREFIX-LENGTH field,
      padding with 0 bits to pad to the end of the last octet needed.

   o  A server receiving an ECS option that uses more ADDRESS octets
      than are needed, or that has non-zero bits set beyond SOURCE
      PREFIX-LENGTH, SHOULD return REFUSED to reject the packet, as a
      signal to the developer of the software making the request to fix
      their implementation.

   All fields are in network byte order ("big-endian", per [RFC1700],
   Data Notation).

Contavalli, et al.        Expires June 17, 2016                 [Page 7]
Internet-Draft        Client Subnet in DNS Queries         December 2015

7.  Protocol Description

7.1.  Originating the Option

   The ECS option should generally be added by Recursive Resolvers when
   querying Authoritative Nameservers, as described in Section 12.  The
   option can also be initialized by a Stub Resolver or Forwarding

7.1.1.  Recursive Resolvers

   The setup of the ECS option in a Recursive Resolver depends on the
   client query that triggered the resolution process.

   In the usual case, where no ECS option was present in the client
   query, the Recursive Resolver initializes the option by setting the
   FAMILY of the client's address.  It then uses the value of its
   maximum cacheable prefix length to set SOURCE PREFIX-LENGTH.  For
   privacy reasons, and because the whole IP address is rarely required
   to determine a tailored response, this length SHOULD be shorter than
   the full address, as described in Section 11.

   If the triggering query included an ECS option itself, it MUST be
   examined for its SOURCE PREFIX-LENGTH.  The Recursive Resolver's
   outgoing query MUST then set SOURCE PREFIX-LENGTH to the shorter of
   the incoming query's SOURCE PREFIX-LENGTH or the server's maximum
   cacheable prefix length.

   Finally, in both cases, SCOPE PREFIX-LENGTH is set to 0 and the
   ADDRESS is then added up to the SOURCE PREFIX-LENGTH number of bits,
   with trailing 0 bits added, if needed, to fill the final octet.  The
   total number of octets used MUST only be enough to cover SOURCE
   PREFIX-LENGTH bits, rather than the full width that would normally be
   used by addresses in FAMILY.

   FAMILY and ADDRESS information MAY be used from the ECS option in the
   incoming query.  Passing the existing address data is supportive of
   the Recursive Resolver being used as the target of a Forwarding
   Resolver, but could possibly run into policy problems with regard to
   usage agreements between the Recursive Resolver and Authoritative
   Nameserver.  See Section 12.2 for more discussion on this point.  If
   the Recursive Resolver will not forward the FAMILY and ADDRESS data
   from the incoming ECS option, it SHOULD return a REFUSED response.

   Subsequent queries to refresh the data MUST, if unrestricted by an
   incoming SOURCE PREFIX-LENGTH, specify the longest SOURCE PREFIX-
   LENGTH that the Recursive Resolver is willing to cache, even if a

Contavalli, et al.        Expires June 17, 2016                 [Page 8]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   previous response indicated that a shorter prefix length was

7.1.2.  Stub Resolvers

   A Stub Resolver MAY generate DNS queries with an ECS option set to
   indicate its own level of privacy via SOURCE PREFIX-LENGTH.  An
   Intermediate Nameserver that receives such a query MUST NOT make
   queries that include more bits of client address than in the
   originating query.

   A SOURCE PREFIX-LENGTH of 0 means the Recursive Resolver MUST NOT add
   address information of the client to its queries.  The subsequent
   Recursive Resolver query to the Authoritative Nameserver will then
   either not include an ECS option or MAY optionally include its own
   address information, which is what the Authoritative Nameserver will
   almost certainly use to generate any Tailored Response in lieu of an
   option.  This allows the answer to be handled by the same caching
   mechanism as other queries, with an explicit indicator of the
   applicable scope.  Subsequent Stub Resolver queries for /0 can then
   be answered from this cached response.

   A Stub Resolver MUST set SCOPE PREFIX-LENGTH to 0.  It MAY include
   FAMILY and ADDRESS data, but should be prepared to handle a REFUSED
   response if the Intermediate Nameserver that it queries has a policy
   that denies forwarding of the ADDRESS.  If there is no ADDRESS set,
   i.e. SOURCE PREFIX-LENGTH is set to 0, FAMILY MUST be set to 0.

7.1.3.  Forwarding Resolvers

   Forwarding Resolvers essentially appear to be Stub Resolvers to
   whatever Recursive Resolver is ultimately handling the query, but
   look like a Recursive Resolver to their client.  A Forwarding
   Resolver using this option MUST prepare it as described in the
   Section 7.1.1 section above.  In particular, a Forwarding Resolver
   that implements this protocol MUST honor SOURCE PREFIX-LENGTH
   restrictions indicated in the incoming query from its client.  See
   also Section 7.5.

   Since the Recursive Resolver it contacts will treat it like a Stub
   Resolver, the Recursive Resolver's policies regarding incoming
   ADDRESS information will apply in the same way.  If the Forwarding
   Resolver receives a REFUSED response when it sends a query which
   includes a non-zero ADDRESS, it MUST retry with FAMILY and ADDRESS
   set to 0.

Contavalli, et al.        Expires June 17, 2016                 [Page 9]
Internet-Draft        Client Subnet in DNS Queries         December 2015

7.2.  Generating a Response

7.2.1.  Authoritative Nameserver

   When a query containing an ECS option is received, an Authoritative
   Nameserver supporting ECS MAY use the address information specified
   in the option in order to generate a tailored response.

   Authoritative Nameservers that have not implemented or enabled
   support for the ECS option ought to safely ignore it within incoming
   queries, per [RFC6891] section 6.1.2.  Such a server MUST NOT include
   an ECS option within replies, to indicate lack of support for it.
   Implementers of Intermediate Nameservers should be aware, however,
   that some nameservers incorrectly echo back unknown EDNS0 options.
   In this protocol that should be mostly harmless, as SCOPE PREFIX-
   LENGTH should come back as 0, thus marking the response as covering
   all networks.

   A query with a wrongly formatted option (e.g., an unknown FAMILY)
   MUST be rejected and a FORMERR response MUST be returned to the
   sender, as described by [RFC6891], Transport Considerations.

   An Authoritative Nameserver that implements this protocol and
   receives an ECS option MUST include an ECS option in its response to
   indicate that it SHOULD be cached accordingly, regardless of whether
   the client information was needed to formulate an answer.  (Note that
   the [RFC6891] requirement to reserve space for the OPT record could
   mean that the answer section of the response will be truncated and
   fallback to TCP indicated accordingly.)  If an ECS option was not
   included in a query, one MUST NOT be included in the response even if
   the server is providing a Tailored Response -- presumably based on
   the address from which it received the query.

   match those in the query, unless the query specified only the SOURCE
   PREFIX-LENGTH for privacy (with FAMILY and ADDRESS set to 0).
   Echoing back these values helps to mitigate certain attack vectors,
   as described in Section 11.

   The SCOPE PREFIX-LENGTH in the response indicates the network for
   which the answer is intended.

   indicates that the provided prefix length was not specific enough to
   select the most appropriate Tailored Response.  Future queries for
   the name within the specified network SHOULD use the longer SCOPE

Contavalli, et al.        Expires June 17, 2016                [Page 10]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   Conversely, a shorter SCOPE PREFIX-LENGTH indicates that more bits
   than necessary were provided, and the answer is suitable for a
   broader range of addresses.  This could be as short as 0, to indicate
   that the answer is suitable for all addresses in FAMILY.

   As the logical topology of any part of the network with regard to the
   tailored response can vary, an Authoritative Nameserver may return
   different values of SCOPE PREFIX-LENGTH for different networks.

   Since some queries can result in multiple RRsets being added to the
   response, there is an unfortunate ambiguity from the original
   specification as to how SCOPE PREFIX-LENGTH would apply to each
   individual RRset.  For example, multiple types in response to an ANY
   metaquery could all have different applicable SCOPE PREFIX-LENGTH
   values, but this protocol only has the ability to signal one.  The
   response SHOULD therefore include the longest relevant PREFIX-LENGTH
   of any RRset in the answer, which could have the unfortunate side-
   effect of redundantly caching some data that could be cached more
   broadly.  For the specific case of a CNAME chain, the Authoritative
   Nameserver SHOULD only place the CNAME to have it cached
   unambiguously appropriately.  Most modern Recursive Resolvers restart
   the query with the canonical name, so the remainder of the chain is
   typically ignored anyway.  For message-focused resolvers, rather than
   RRset-focused ones, this will mean caching the entire CNAME chain at
   the longest PREFIX-LENGTH of any RRset in the chain.

   The specific logic that an Authoritative Nameserver uses to choose a
   tailored response is not in the scope of this document.  Implementers
   are encouraged, however, to consider carefully their selection of
   SCOPE PREFIX-LENGTH for the response in the event that the best
   tailored response cannot be determined, and what the implications
   would be over the life of the TTL.

   If the Authoritative Nameserver operator configures a more specific
   (longer prefix length) Tailored Response within a configured less
   specific (shorter prefix length) Tailored Response, then
   implementations can either:

   1.  Deaggregate the shorter prefix response into multiple longer
       prefix responses, or,

   2.  Alert the operator that the order of queries will determine which
       answers get cached, and either warn and continue or treat this as
       an error and refuse to load the configuration.

   This choice should be documented for the operator, for example in the
   user manual.

Contavalli, et al.        Expires June 17, 2016                [Page 11]
Internet-Draft        Client Subnet in DNS Queries         December 2015

7.2.2.  Intermediate Nameserver

   When an Intermediate Nameserver uses ECS, whether it passes an ECS
   option in its own response to its client is predicated on whether the
   client originally included the option.  Because a client that did not
   use an ECS option might not be able to understand it, the server MUST
   NOT provide one in its response.  If the client query did include the
   option, the server MUST include one in its response, especially as it
   could be talking to a Forwarding Resolver which would need the
   information for its own caching.

   If an Intermediate Nameserver receives a response which has a longer
   SCOPE PREFIX-LENGTH than the SOURCE PREFIX-LENGTH that it provided in
   its query, it SHOULD still provide the result as the answer to the
   triggering client request even if the client is in a different
   address range.  The Intermediate Nameserver MAY instead opt to retry
   with a longer SOURCE PREFIX-LENGTH to get a better reply before
   responding to its client, as long as it does not exceed a SOURCE
   PREFIX-LENGTH specified in the query that triggered resolution, but
   this obviously has implications for the latency of the overall

   The logic for using the cache to determine whether the Intermediate
   Nameserver already knows the response to provide to its client is
   covered in the next section.

7.3.  Handling ECS Responses and Caching

   When an Intermediate Nameserver receives a response containing an ECS
   option and without the TC bit set, it SHOULD cache the result based
   on the data in the option.  If the TC bit was set, the Intermediate
   Resolver SHOULD retry the query over TCP to get the complete answer
   section for caching.

   ADDRESS in the response don't match the non-zero fields in the
   corresponding query, the full response MUST be dropped, as described
   in Section 11.  For a response to a query which specified only the
   SOURCE PREFIX-LENGTH for privacy masking, the FAMILY and ADDRESS
   fields should contain the appropriate non-zero information for

   If no ECS option is contained in the response, the Intermediate
   Nameserver SHOULD treat this as being equivalent to having received a
   SCOPE PREFIX-LENGTH of 0, which is an answer suitable for all client
   addresses.  See further discussion on the security implications of
   this in Section 11.

Contavalli, et al.        Expires June 17, 2016                [Page 12]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   If a REFUSED response is received from an Authoritative Nameserver,
   an ECS-aware resolver MUST retry the query without ECS to distinguish
   the response from one where the Authoritative Nameserver is not
   responsible for the name, which is a common convention for the
   REFUSED status.  Similarly, a client of a Recursive Resolver should
   retry for REFUSED because it is not sufficiently clear whether the
   REFUSED was because of the ECS option or some other reason.

7.3.1.  Caching the Response

   In the cache, all resource records in the answer section MUST be tied
   to the network specified by the FAMILY, ADDRESS and SCOPE PREFIX-
   LENGTH fields, as limited by the Intermediate Nameserver's own
   configuration for maximum cacheable prefix length.  Note that the
   additional and authority sections from a DNS response message are
   specifically excluded here.  Any records from these sections MUST NOT
   be tied to a network.  See more at Section 7.4.

   Records that are cached as /0 because of a query's SOURCE PREFIX-
   LENGTH of 0 MUST be distinguished from those that are cached as /0
   because of a response's SCOPE PREFIX-LENGTH of 0.  The former should
   only be used for other /0 queries that the Intermediate Resolver
   receives, but the latter is suitable as a response for all networks.

   Although omitting network-specific caching will significantly
   simplify an implementation, the resulting drop in cache hits is very
   likely to defeat most latency benefits provided by ECS.  Therefore,
   when implementing this option for latency purposes, implementing full
   caching support as described in this section is strongly recommended.

   Enabling support for ECS in an Intermediate Nameserver will
   significantly increase the size of the cache, reduce the number of
   results that can be served from cache, and increase the load on the
   server.  Implementing the mitigation techniques described in
   Section 11 is strongly recommended.

7.3.2.  Answering from Cache

   Cache lookups are first done as usual for a DNS query, using the
   query tuple of <name, type, class>.  Then the appropriate RRset MUST
   be chosen based on longest prefix matching.  The client address to
   use for comparison will depend on whether the Intermediate Nameserver
   received an ECS option in its client query.

   o  If no ECS option was provided, the client's address is used.

   o  If there was an ECS option, the ADDRESS from it MAY be used if
      local policy allows.  Policy can vary depending on the agreements

Contavalli, et al.        Expires June 17, 2016                [Page 13]
Internet-Draft        Client Subnet in DNS Queries         December 2015

      the operator of the Intermediate Nameserver has with Authoritative
      Nameserver operators; see Section 12.2.  If policy does not allow,
      a REFUSED response must be sent.

   If a matching network is found and the relevant data is unexpired,
   the response is generated as per Section 7.2.

   If no matching network is found, the Intermediate Nameserver MUST
   perform resolution as usual.  This is necessary to avoid Tailored
   Responses in the cache from being returned to the wrong clients, and
   to avoid a single query coming from a client on a different network
   from polluting the cache with a Tailored Response for all the users
   of that resolver.

7.4.  Delegations and Negative Answers

   The prohibition against tying ECS data to records from the Authority
   and Additional section left an unfortunate ambiguity in the original
   specification, primarily with regard to negative answers.  The
   expectation of the original authors was that ECS would only really be
   used for address requests and the positive result in the response's
   answer section, the use case that was driving the definition of the

   The delegations case is a bit easier to tease out.  In operational
   practice, if an authoritative server is using address information to
   provide customized delegations, it is the resolver that will be using
   the answer for its next iterative query.  Addresses in the Additional
   section SHOULD therefore ignore ECS data, and the authority SHOULD
   return a zero SCOPE PREFIX-LENGTH on delegations.  A recursive
   resolver SHOULD treat a non-zero SCOPE PREFIX LENGTH in a delegation
   as though it were zero.

   For negative answers, some independent implementations of both
   resolvers and authorities did not see the section restriction as
   necessarily meaning that a given name and type must only have either
   positive ECS-tagged answers or a negative answer.  They support being
   able to tell one part of the network that the data does not exist,
   while telling another part of the network that it does.

   Several other implementations, however, do not support being able to
   mix positive and negative answers, and thus interoperability is a
   problem.  It is recommended that no specific behaviour regarding
   negative answers be relied upon.

   This issue is expected to be revisited in a future revision of the
   protocol, possibly blessing the mixing of positive and negative

Contavalli, et al.        Expires June 17, 2016                [Page 14]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   answers.  There are implications for cache data structures that
   developers should consider when writing new ECS code.

7.5.  Transitivity

   Generally, ECS options will only be present in DNS messages between a
   Recursive Resolver and an Authoritative Nameserver, i.e., one hop.
   In certain configurations however, for example multi-tier nameserver
   setups, it may be necessary to implement transitive behaviour on
   Intermediate Nameservers.

   Any Intermediate Nameserver that forwards ECS options received from
   their clients MUST fully implement the caching behaviour described in
   Section 7.3.

   An Intermediate Nameserver MAY forward ECS options with address
   information.  This information MAY match the source IP address of the
   incoming query, and MAY have more or fewer address bits than the
   Nameserver would normally include in a locally originated ECS option.
   If an Intermediate Nameservers receives a query with SOURCE PREFIX-
   LENGTH set to 0 it MUST forward the query as-is and MUST NOT replace
   it with more accurate address information.

   If for any reason the Intermediate Nameserver does not want to use
   the information in an ECS option it receives (too little address
   information, network address from a range not authorized to use the
   server, private/unroutable address space, etc), it SHOULD drop the
   query and return a REFUSED response.  Note again that a query MUST
   NOT be refused solely because it provides 0 address bits.

   Be aware that at least one major existing implementation does not
   return REFUSED and instead just process the query as though the
   problematic information were not present.  This can lead to anomalous
   situations, such as a response from the Intermediate Nameserver that
   indicates it is tailored for one network (the one passed in the
   original query, since ADDRESS must match) when actually it is for
   another network (the one which contains the address that the
   Intermediate Nameserver saw as making the query).

8.  IANA Considerations

   IANA has already assigned option code 8 in the "DNS EDNS0 Option
   Codes (OPT)" registry to ECS.

   The IANA is requested to update the reference ("draft-vandergaast-
   edns-client-subnet") to refer to this RFC when published.

Contavalli, et al.        Expires June 17, 2016                [Page 15]
Internet-Draft        Client Subnet in DNS Queries         December 2015

9.  DNSSEC Considerations

   The presence or absence of an [RFC6891] EDNS0 OPT resource record
   containing an ECS option in a DNS query does not change the usage of
   the resource records and mechanisms used to provide data origin
   authentication and data integrity to the DNS, as described in
   [RFC4033], [RFC4034] and [RFC4035].  OPT records are not signed.

   Use of this option, however, does imply increased DNS traffic between
   any given Recursive Resolver and Authoritative Nameserver, which
   could be another barrier to further DNSSEC adoption in this area.

10.  NAT Considerations

   Special awareness of ECS in devices that perform Network Address
   Translation (NAT) as described in [RFC2663] is not required; queries
   can be passed through as-is.  The client's network address SHOULD NOT
   be added, and existing ECS options, if present, SHOULD NOT be
   modified by NAT devices.

   In large-scale global networks behind a NAT device (but for example
   with Centralized Resolver infrastructure), an internal Intermediate
   Nameserver might have detailed network layout information, and may
   know which external subnets are used for egress traffic by each
   internal network.  In such cases, the Intermediate Nameserver MAY use
   that information when originating ECS options.

   In other cases, if a Recursive Resolvers knows it is sited behind a
   NAT device, it SHOULD NOT originate ECS options with their external
   IP address, and instead rely on downstream Intermediate Nameservers
   to do so.  They MAY, however, choose to include the option with their
   internal address for the purposes of signaling a shorter, more

   If an Authoritative Nameserver on the publicly routed Internet
   receives a query that specifies an ADDRESS in [RFC1918] or [RFC4193]
   private address space, it SHOULD ignore ADDRESS and look up its
   answer based on the address of the Recursive Resolver.  In the
   response it SHOULD set SCOPE PREFIX-LENGTH to cover all of the
   relevant private space.  For example, a query for ADDRESS
   with a SOURCE PREFIX-LENGTH of 24 would get a returned SCOPE PREFIX-
   LENGTH of 8.  The Intermediate Nameserver MAY elect to cache the
   answer under one entry for special-purpose addresses [RFC6890]; see
   Section 11.3.

Contavalli, et al.        Expires June 17, 2016                [Page 16]
Internet-Draft        Client Subnet in DNS Queries         December 2015

11.  Security Considerations

11.1.  Privacy

   With the ECS option, the network address of the client that initiated
   the resolution becomes visible to all servers involved in the
   resolution process.  Additionally, it will be visible from any
   network traversed by the DNS packets.

   To protect users' privacy, Recursive Resolvers are strongly
   encouraged to conceal part of the IP address of the user by
   truncating IPv4 addresses to 24 bits. 56 bits are recommended for
   IPv6, based on [RFC6177].

   ISPs should have more detailed knowledge of their own networks.  That
   is, they might know that all 24-bit prefixes in a /20 are in the same
   area.  In those cases, for optimal cache utilization and improved
   privacy, the ISP's Recursive Resolver SHOULD truncate IP addresses in
   this /20 to just 20 bits, instead of 24 as recommended above.

   Users who wish their full IP address to be hidden can include an ECS
   option specifying the wildcard address (i.e.  SOURCE PREFIX-LENGTH of
   0).  As described in previous sections, this option will be forwarded
   across all the Recursive Resolvers supporting ECS, which MUST NOT
   modify it to include the network address of the client.

   Note that even without an ECS option, any server queried directly by
   the user will be able to see the full client IP address.  Recursive
   Resolvers or Authoritative Nameservers MAY use the source IP address
   of queries to return a cached entry or to generate a Tailored
   Response that best matches the query.

11.2.  Birthday Attacks

   ECS adds information to the DNS query tupe (q-tuple).  This allows an
   attacker to send a caching Intermediate Nameserver multiple queries
   with spoofed IP addresses either in the ECS option or as the source
   IP.  These queries will trigger multiple outgoing queries with the
   same name, type and class, just different address information in the
   ECS option.

   With multiple queries for the same name in flight, the attacker has a
   higher chance of success to send a matching response with the SCOPE
   PREFIX-LENGTH set to 0 to get it cached for all hosts.

   To counter this, the ECS option in a response packet MUST contain the
   full FAMILY, ADDRESS and SOURCE PREFIX-LENGTH fields from the
   corresponding query.  Intermediate Nameservers processing a response

Contavalli, et al.        Expires June 17, 2016                [Page 17]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   MUST verify that these match, and SHOULD discard the entire response
   if they do not.

   That requirement to discard is "SHOULD" instead of "MUST" because it
   stands in opposition to the instruction in Section 7.3 which states
   that a response lacking an ECS option should be treated as though it
   had one of SCOPE PREFIX-LENGTH of 0.  If that is always true, then an
   attacker does not need to worry about matching the original ECS
   option data and just needs to flood back responses that have no ECS
   option at all.

   This type of attack could be detected in ongoing operations by
   marking whether the responding nameserver had previously been sending
   ECS option, and/or by taking note of an incoming flood of bogus
   responses and flagging the relevant query for re-resolution.  This is
   more complex than existing nameserver responses to spoof floods, and
   would also need to be sensitive to a nameserver legitimately stopping
   ECS replies even though it had previously given them.

11.3.  Cache Pollution

   It is simple for an arbitrary resolver or client to provide false
   information in the ECS option, or to send UDP packets with forged
   source IP addresses.

   This could be used to:

   o  pollute the cache of intermediate resolvers, by filling it with
      results that will rarely (if ever) be used.

   o  reverse engineer the algorithms (or data) used by the
      Authoritative Nameserver to calculate Tailored Responses.

   o  mount a denial-of-service attack against an Intermediate
      Nameserver, by forcing it to perform many more recursive queries
      than it would normally do, due to how caching is handled for
      queries containing the ECS option.

   Even without malicious intent, Centralized Resolvers providing
   answers to clients in multiple networks will need to cache different
   responses for different networks, putting more memory pressure on the

   To mitigate those problems:

   o  Recursive Resolvers implementing ECS should only enable it in
      deployments where it is expected to bring clear advantages to the
      end users.  For example, when expecting clients from a variety of

Contavalli, et al.        Expires June 17, 2016                [Page 18]
Internet-Draft        Client Subnet in DNS Queries         December 2015

      networks or from a wide geographical area.  Due to the high cache
      pressure introduced by ECS, the feature SHOULD be disabled in all
      default configurations.

   o  Recursive Resolvers SHOULD limit the number of networks and
      answers they keep in the cache for any given query.

   o  Recursive Resolvers SHOULD limit the number of total different
      networks that they keep in cache.

   o  Recursive Resolvers MUST NOT send an ECS option with a SOURCE
      PREFIX-LENGTH providing more bits in the ADDRESS than they are
      willing to cache responses for.

   o  Recursive Resolvers should implement algorithms to improve the
      cache hit rate, given the size constraints indicated above.
      Recursive Resolvers MAY, for example, decide to discard more
      specific cache entries first.

   o  Authoritative Nameservers and Recursive Resolvers should discard
      ECS options that are either obviously forged or otherwise known to
      be wrong.  They SHOULD at least treat unroutable addresses, such
      as some of the address blocks defined in [RFC6890], as equivalent
      to the Recursive Resolver's own identity.  They SHOULD ignore and
      never forward ECS options specifying other routable addresses that
      are known not to be served by the query source.

   o  Authoritative Nameservers consider the ECS option just as a hint
      to provide better results.  They can decide to ignore the content
      of the ECS option based on black or white lists, rate limiting
      mechanisms, or any other logic implemented in the software.

12.  Sending the Option

   When implementing a Recursive Resolver, there are two strategies on
   deciding when to include an ECS option in a query.  At this stage,
   it's not clear which strategy is best.

12.1.  Probing

   A Recursive Resolver can send the ECS option with every outgoing
   query.  However, it is RECOMMENDED that Resolvers remember which
   Authoritative Nameservers did not return the option with their
   response, and omit client address information from subsequent queries
   to those Nameservers.

   Additionally, Recursive Resolvers SHOULD be configured to never send
   the option when querying root, top-level, and effective top-level

Contavalli, et al.        Expires June 17, 2016                [Page 19]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   (ie, ("public suffix") [Public_Suffix_List] domain servers.  These
   domains are delegation-centric and are very unlikely to generate
   different responses based on the address of the client.

   When probing, it is important that several things are probed: support
   for ECS, support for EDNS0, support for EDNS0 options, or possibly an
   unreachable Nameserver.  Various implementations are known to drop
   DNS packets with OPT RRs (with or without options), thus several
   probes are required to discover what is supported.

   Probing, if implemented, MUST be repeated periodically, e.g., daily.
   If an Authoritative Nameserver indicates ECS support for one zone, it
   is to be expected that the Nameserver supports ECS for all of its
   zones.  Likewise, an Authoritative Nameserver that uses ECS
   information for one of its zones, MUST indicate support for the
   option in all of its responses to ECS queries.  If the option is
   supported but not actually used for generating a response, its SCOPE
   PREFIX-LENGTH MUST be set to 0.

12.2.  Whitelist

   As described previously, it is expected that only a few Recursive
   Resolvers will need to use ECS, and that it will generally be enabled
   only if it offers a clear benefit to the users.

   To avoid the complexity of implementing a probing and detection
   mechanism (and the possible query loss/delay that may come with it),
   an implementation could use a whitelist of Authoritative Nameservers
   to send the option to, likely specified by their domain name.
   Implementations MAY also allow additionally configuring this based on
   other criteria, such as zone or query type.  As of the time of this
   writing, at least one implementation makes use of a whitelist.

   An advantage of using a whitelist is that partial client address
   information is only disclosed to Nameservers that are known to use
   the information, improving privacy.

   A drawback is saleability.  The operator needs to track which
   Authoritative Nameservers support ECS, making it harder for new
   Authoritative Nameservers to start using the option.

   Similarly, Authoritative Nameservers can also use whitelists to limit
   the feature to only certain clients.  For example, a CDN that does
   not want all of their mapping trivially walked might require a legal
   agreement with the Recursive Resolver operator, to clearly describe
   the acceptable use of the feature.

Contavalli, et al.        Expires June 17, 2016                [Page 20]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   The maintenance of access control mechanisms is out of scope for this
   protocol definition.

13.  Example

   1.   A stub resolver, SR, with IP address tries to resolve, by forwarding the query to the Recursive
        Resolver, RNS, from IP address IP, asking for recursion.

   2.   RNS, supporting ECS, looks up in its cache.  An
        entry is found neither for, nor for

   3.   RNS builds a query to send to the root and .com servers.  The
        implementation of RNS provides facilities so an administrator
        can configure it not to forward ECS in certain cases.  In
        particular, RNS is configured to not include an ECS option when
        talking to TLD or root nameservers, as described in Section 7.1.
        Thus, no ECS option is added, and resolution is performed as

   4.   RNS now knows the next server to query: the Authoritative
        Nameserver, ANS, responsible for

   5.   RNS prepares a new query for, including an ECS
        option with:

        *  OPTION-CODE, set to 8.

        *  OPTION-LENGTH, set to 0x00 0x07 for the following fixed 4
           octets plus the 3 octets that will be used for ADDRESS.

        *  FAMILY, set to 0x00 0x01 as IP is an IPv4 address.

        *  SOURCE PREFIX-LENGTH, set to 0x18, as RNS is configured to
           conceal the last 8 bits of every IPv4 address.

        *  SCOPE PREFIX-LENGTH, set to 0x00, as specified by this
           document for all queries.

        *  ADDRESS, set to 0xC0 0x00 0x02, providing only the first 24
           bits of the IPv4 address.

   6.   The query is sent.  ANS understands and uses ECS.  It parses the
        ECS option, and generates a Tailored Response.

   7.   Due its internal implementation, ANS finds a response that is
        tailored for the whole /16 of the client that performed the

Contavalli, et al.        Expires June 17, 2016                [Page 21]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   8.   ANS adds an ECS option in the response, containing:

        *  OPTION-CODE, set to 8.

        *  OPTION-LENGTH, set to 0x00 0x07.

        *  FAMILY, set to 0x00 0x01.

        *  SOURCE PREFIX-LENGTH, set to 0x18, copied from the query.

        *  SCOPE PREFIX-LENGTH, set to 0x10, indicating a /16 network.

        *  ADDRESS, set to 0xC0 0x00 0x02, copied from the query.

   9.   RNS receives the response containing an ECS option.  It verifies
        that FAMILY, SOURCE PREFIX-LENGTH, and ADDRESS match the query.
        If not, the message is discarded.

   10.  The response is interpreted as usual.  Since the response
        contains an ECS option, the ADDRESS, SCOPE PREFIX-LENGTH, and
        FAMILY in the response are used to cache the entry.

   11.  RNS sends a response to stub resolver SR, without including an
        ECS option.

   12.  RNS receives another query to resolve  This
        time, a response is cached.  The response, however, is tied to a
        particular network.  If the address of the client matches any
        network in the cache, then the response is returned from the
        cache.  Otherwise, another query is performed.  If multiple
        results match, the one with the longest SCOPE PREFIX-LENGTH is
        chosen, as per common best-network match algorithms.

14.  Contributing Authors

   The below individuals contributed significantly to the document.  The
   RFC Editor prefers a maximum of 5 names on the front page, and so we
   have listed additional authors in this section

   Edward Lewis
   12025 Waterfront Drive, Suite 300
   Los Angeles CA 90094-2536

Contavalli, et al.        Expires June 17, 2016                [Page 22]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   Sean Leach
   POBox 78266
   San Francisco CA 94107

   Jason Moreau
   Akamai Technologies
   8 Cambridge Ctr
   Cambridge MA 02142-1413

15.  Acknowledgements

   The authors wish to thank Darryl Rodden for his work as a co-author
   on previous versions, and the following people for reviewing early
   drafts of this document and for providing useful feedback: Paul S.
   R.  Chisholm, B.  Narendran, Leonidas Kontothanassis, David Presotto,
   Philip Rowlands, Chris Morrow, Kara Moscoe, Alex Nizhner, Warren
   Kumari, and Richard Rabbat from Google; Terry Farmer, Mark Teodoro,
   Edward Lewis, and Eric Burger from Neustar; David Ulevitch and
   Matthew Dempsky from OpenDNS; Patrick W.  Gilmore and Steve Hill from
   Akamai; Colm MacCarthaigh and Richard Sheehan from Amazon; Tatuya
   Jinmei from Infoblox; Andrew Sullivan from Dyn; John Dickinson from
   Sinodun; Mark Delany from Apple; Yuri Schaeffer from NLnet Labs;
   Duane Wessels from from Verisign; Antonio Querubin; Daniel Kahn
   Gillmor from the ACLU, Russ Housley and all of the other people that
   replied to our emails on various mailing lists.

16.  References

16.1.  Normative References

   [RFC1034]  Mockapetris, P., "Domain names - concepts and facilities",
              STD 13, RFC 1034, DOI 10.17487/RFC1034, November 1987,

   [RFC1035]  Mockapetris, P., "Domain names - implementation and
              specification", STD 13, RFC 1035, DOI 10.17487/RFC1035,
              November 1987, <>.

   [RFC1700]  Reynolds, J. and J. Postel, "Assigned Numbers", RFC 1700,
              DOI 10.17487/RFC1700, October 1994,

   [RFC1918]  Rekhter, Y., Moskowitz, B., Karrenberg, D., de Groot, G.,
              and E. Lear, "Address Allocation for Private Internets",
              BCP 5, RFC 1918, DOI 10.17487/RFC1918, February 1996,

Contavalli, et al.        Expires June 17, 2016                [Page 23]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
              RFC2119, March 1997,

   [RFC4033]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "DNS Security Introduction and Requirements", RFC
              4033, DOI 10.17487/RFC4033, March 2005,

   [RFC4034]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "Resource Records for the DNS Security Extensions",
              RFC 4034, DOI 10.17487/RFC4034, March 2005,

   [RFC4035]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "Protocol Modifications for the DNS Security
              Extensions", RFC 4035, DOI 10.17487/RFC4035, March 2005,

   [RFC4193]  Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast
              Addresses", RFC 4193, DOI 10.17487/RFC4193, October 2005,

   [RFC6177]  Narten, T., Huston, G., and L. Roberts, "IPv6 Address
              Assignment to End Sites", BCP 157, RFC 6177, DOI 10.17487/
              RFC6177, March 2011,

   [RFC6890]  Cotton, M., Vegoda, L., Bonica, R., Ed., and B. Haberman,
              "Special-Purpose IP Address Registries", BCP 153, RFC
              6890, DOI 10.17487/RFC6890, April 2013,

   [RFC6891]  Damas, J., Graff, M., and P. Vixie, "Extension Mechanisms
              for DNS (EDNS(0))", STD 75, RFC 6891, DOI 10.17487/
              RFC6891, April 2013,

16.2.  Informative References

              "Address Family Numbers",

Contavalli, et al.        Expires June 17, 2016                [Page 24]
Internet-Draft        Client Subnet in DNS Queries         December 2015

              "DPRIVE Working Group",

              Hardie, T., "Design considerations for Metadata
              Insertion", draft-hardie-privsec-metadata-insertion-00
              (work in progress), October 2015.

              Contavalli, C., Gaast, W., Leach, S., and E. Lewis,
              "Client Subnet in DNS Requests", draft-vandergaast-edns-
              client-subnet-02 (work in progress), July 2013.

              "Public Suffix List", <>.

   [RFC2308]  Andrews, M., "Negative Caching of DNS Queries (DNS
              NCACHE)", RFC 2308, DOI 10.17487/RFC2308, March 1998,

   [RFC2663]  Srisuresh, P. and M. Holdrege, "IP Network Address
              Translator (NAT) Terminology and Considerations", RFC
              2663, DOI 10.17487/RFC2663, August 1999,

Appendix A.  Document History

   [RFC Editor: Please delete this section before publication.]

   -05 to -06:

   o  Integrated David Lawrence comments.

   o  Ran spellcheck again.  One ady I';; laern to tyoe/

   -04 to -05:

   o  Moved comment about retrying for REFUSED to section on "Handling
      ECS Responses".  (Jinmei)

   o  Clarify that a new proposal for an improved ECS protool is

   o  "Forwarders" had been used as though they were the source of a
      forwarded query rather than the targeted of one; clarified and
      defined as "Forwarding Resolver".  (Jinmei)

Contavalli, et al.        Expires June 17, 2016                [Page 25]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   o  "representing the leftmost significant bits" => "representing the
      leftmost number of significant bits".  (Jinmei)

   o  Minor other clarifying text.  (Jinmei)

   o  Jinmei's affiliation.

   o  Minor wording clarifications.  (David Kahn Gillmor)

   o  Russ Housely's GenART review.

   -03 to -04:

   o  Privacy note per Ted Hardie's suggestion.

   o  MUST use minimum octet length to cover PREFIX bits.

   o  Expose note about documenting deployed, if flawed, protocol.

   -02 to -03:

   o  Some cleanup of the whitelist text.

   -01 to -02 (IETF)

   o  Clean up the open issues, mostly by saying that they were out of
      scope for this document.

   o  How in the world did no reviewers note that "Queries" had been
      spelled as "Querys" in the title?  (Aaron Falk did.)

   -00 to -01 (IETF)

   o  Note ambiguity with multiple RRsets appearing in reply, eg, for an
      ANY query or CNAME chain.  (Duane Wessels)

   o  Open issue questioning the guidance about resolvers behind a NAT.
      How do they know they are?  What real requirement is this
      imposing?  (Duane Wessels)

   o  Some other wording changes based on Duane's review of an earlier

   -IND to -00 (IETF)

   o  <David> Made the document describe how things are actually
      implmented now.  This makes the document be more of a "this is how

Contavalli, et al.        Expires June 17, 2016                [Page 26]
Internet-Draft        Client Subnet in DNS Queries         December 2015

      we are doing things, this provides information on that".  There
      may be a future document that describes additional funcationality.

   o  NETMASK was not a good desription, changed to PREFIX-LENGTH
      (Jinmei, others).  Stole most of the definition for prefix length
      from RFC4291.

   o  Fixed the "SOURCE PREFIX-LENGTH set to 0" definition to include
      IPv6 (Tatuya Jinmei)

   o  Comment that ECS cannot be used to hand NXDOMAIN to some clients
      and not others, primarily because of interoperability issues.
      (Tatuya Jinmei)

   o  Added text explaining that implmentations need to document thier
      behavior with overlapping networks.

   o  Soften "optimized reply" language.  (Andrew Sullivan).

   o  Fixed some of legacy IPv4 cruft (things like

   o  Some more grammar / working cleanups.

   o  Replaced a whole heap of occurances of "edns-client-subnet" with
      "ECS" for readability.  (John Dickinson)

   o  More clearly describe the process from the point of view of each
      type of nameserver.  (John Dickinson)

   o  Birthday attack still possible if attacker floods with ECS-less
      responses.  (Yuri Schaeffer)

   o  Added some open issues directly to the text.

A.1.  -00

   o  Document moved to experimental track, added experiment description
      in header with details in a new section.

   o  Specifically note that ECS applies to the answer section only.

   o  Warn that caching based on ECS is optional but very important for
      performance reasons.

   o  Updated NAT section.

Contavalli, et al.        Expires June 17, 2016                [Page 27]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   o  Added recommendation to not use the default /24 recommendation for
      the source prefix-length field if more detailed information about
      the network is available.

   o  Rewritten problem statement to be more clear about the goal of ECS
      and the fact that it's entirely optional.

   o  Wire format changed to include the original address and prefix
      length in responses in defence against birthday attacks.

   o  Security considerations now includes a section about birthday

   o  Renamed edns-client-ip in ECS, following suggestions on the
      mailing list.

   o  Clarified behavior of resolvers when presented with an invalid ECS

   o  Fully take multi-tier DNS setups in mind and be more clear about
      where the option should be originated.

   o  A note on Authoritative Nameservers receiving queries that specify
      private address space.

   o  A note to always ask for the longest acceptable SOURCE prefix
      length, even if a prior answer indicated that a shorter prefix
      length was suitable.

   o  Marked up a few more references.

   o  Added a few definitions in the Terminology section, and a few more
      aesthetic changes in the rest of the document.

A.2.  -01

   o  Document version number reset from -02 to -00 due to the rename of
      base document.

   o  Clarified example (dealing with TLDs, and various minor errors).

   o  Referencing RFC5035 instead of RFC1918.

   o  Added a section on probing (and how it should be done) vs.

   o  Moved description on how to forward ECS option in dedicated

Contavalli, et al.        Expires June 17, 2016                [Page 28]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   o  Queries with wrongly formatted ECS options should now be rejected
      with FORMERR.

   o  Added an "Overview" section, providing an introduction to the

   o  Intermediate Nameservers can now remove an ECS option, or reduce
      the SOURCE PREFIX-LENGTH to increase privacy.

   o  Added a reference to DoS attacks in the Security section.

   o  Don't use "network range", as it seems to have different meaning
      in other contexts, and turned out to be confusing.

   o  Use shorter and longer prefix lengths, rather than higher or
      lower.  Add a better explanation in the format section.

   o  Minor corrections in various other sections.

A.3.  -02

   o  Added IANA-assigned option code.

Authors' Addresses

   Carlo Contavalli
   1600 Amphitheater Parkway
   Mountain View, CA  94043


   Wilmer van der Gaast
   Belgrave House, 76 Buckingham Palace Road
   London  SW1W 9TQ


Contavalli, et al.        Expires June 17, 2016                [Page 29]
Internet-Draft        Client Subnet in DNS Queries         December 2015

   David C Lawrence
   Akamai Technologies
   8 Cambridge Center
   Cambridge, MA  02142


   Warren Kumari
   1600 Amphitheatre Parkway
   Mountain View, CA  94043


Contavalli, et al.        Expires June 17, 2016                [Page 30]