ForCES Inter-FE LFB
draft-ietf-forces-interfelfb-02
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 8013.
|
|
|---|---|---|---|
| Authors | Damascane M. Joachimpillai , Jamal Hadi Salim | ||
| Last updated | 2015-11-02 | ||
| Replaces | draft-joachimpillai-forces-interfelfb | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
GENART Last Call review
(of
-04)
by Russ Housley
Almost ready
OPSDIR Last Call review
by Will LIU
Has nits
|
||
| Stream | WG state | WG Document | |
| Document shepherd | Evangelos Haleplidis | ||
| Shepherd write-up | Show Last changed 2015-05-27 | ||
| IESG | IESG state | Became RFC 8013 (Proposed Standard) | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | Alia Atlas | ||
| IESG note | |||
| Send notices to | (None) |
draft-ietf-forces-interfelfb-02
Internet Engineering Task Force D. Joachimpillai
Internet-Draft Verizon
Intended status: Standards Track J. Hadi Salim
Expires: May 5, 2016 Mojatatu Networks
November 2, 2015
ForCES Inter-FE LFB
draft-ietf-forces-interfelfb-02
Abstract
This document describes how to extend the ForCES LFB topology across
FEs by defining the Inter-FE LFB Class. The Inter-FE LFB Class
provides the ability to pass data and metadata across FEs without
needing any changes to the ForCES specification. The document
focuses on Ethernet transport.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 5, 2016.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 1]
Internet-Draft ForCES Inter-FE LFB November 2015
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Terminology and Conventions . . . . . . . . . . . . . . . . . 3
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
1.2. Definitions . . . . . . . . . . . . . . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Problem Scope And Use Cases . . . . . . . . . . . . . . . . . 4
3.1. Assumptions . . . . . . . . . . . . . . . . . . . . . . . 4
3.2. Sample Use Cases . . . . . . . . . . . . . . . . . . . . 4
3.2.1. Basic IPv4 Router . . . . . . . . . . . . . . . . . . 4
3.2.1.1. Distributing The Basic IPv4 Router . . . . . . . 6
3.2.2. Arbitrary Network Function . . . . . . . . . . . . . 7
3.2.2.1. Distributing The Arbitrary Network Function . . . 7
4. Inter-FE LFB Overview . . . . . . . . . . . . . . . . . . . . 8
4.1. Inserting The Inter-FE LFB . . . . . . . . . . . . . . . 8
5. Inter-FE Ethernet Connectivity . . . . . . . . . . . . . . . 10
5.1. Inter-FE Ethernet Connectivity Issues . . . . . . . . . . 10
5.1.1. MTU Consideration . . . . . . . . . . . . . . . . . . 10
5.1.2. Quality Of Service Considerations . . . . . . . . . . 11
5.1.3. Congestion Considerations . . . . . . . . . . . . . . 11
5.1.4. Deployment Considerations . . . . . . . . . . . . . . 11
5.2. Inter-FE Ethernet Encapsulation . . . . . . . . . . . . . 12
6. Detailed Description of the Ethernet inter-FE LFB . . . . . . 13
6.1. Data Handling . . . . . . . . . . . . . . . . . . . . . . 13
6.1.1. Egress Processing . . . . . . . . . . . . . . . . . . 14
6.1.2. Ingress Processing . . . . . . . . . . . . . . . . . 15
6.2. Components . . . . . . . . . . . . . . . . . . . . . . . 16
6.3. Inter-FE LFB XML Model . . . . . . . . . . . . . . . . . 16
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 21
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 21
9. IEEE Assignment Considerations . . . . . . . . . . . . . . . 21
10. Security Considerations . . . . . . . . . . . . . . . . . . . 21
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 22
11.1. Normative References . . . . . . . . . . . . . . . . . . 22
11.2. Informative References . . . . . . . . . . . . . . . . . 23
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 24
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 2]
Internet-Draft ForCES Inter-FE LFB November 2015
1. Terminology and Conventions
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
1.2. Definitions
This document reiterates the terminology defined in several ForCES
documents [RFC3746], [RFC5810], [RFC5811], and [RFC5812] [RFC7391]
[RFC7408] for the sake of contextual clarity.
Control Engine (CE)
Forwarding Engine (FE)
FE Model
LFB (Logical Functional Block) Class (or type)
LFB Instance
LFB Model
LFB Metadata
ForCES Component
LFB Component
ForCES Protocol Layer (ForCES PL)
ForCES Protocol Transport Mapping Layer (ForCES TML)
2. Introduction
In the ForCES architecture, a packet service can be modelled by
composing a graph of one or more LFB instances. The reader is
referred to the details in the ForCES Model [RFC5812].
The current ForCES model describes the processing within a single
Forwarding Element (FE) in terms of logical forwarding blocks (LFB),
including provision for the Control Element (CE) to establish and
modify that processing sequence, and the parameters of the individual
LFBs.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 3]
Internet-Draft ForCES Inter-FE LFB November 2015
Under some circumstance, it would be beneficial to be able to extend
this view, and the resulting processing across more than one FE.
This may be in order to achieve scale by splitting the processing
across elements, or to utilize specialized hardware available on
specific FEs.
Given that the ForCES inter-LFB architecture calls out for the
ability to pass metadata between LFBs, it is imperative therefore to
define mechanisms to extend that existing feature and allow passing
the metadata between LFBs across FEs.
This document describes how to extend the LFB topology across FEs i.e
inter-FE connectivity without needing any changes to the ForCES
definitions. It focuses on using Ethernet as the interconnection
between FEs.
3. Problem Scope And Use Cases
The scope of this document is to solve the challenge of passing
ForCES defined metadata alongside packet data across FEs (be they
physical or virtual) for the purpose of distributing the LFB
processing.
3.1. Assumptions
o The FEs involved in the Inter-FE LFB belong to the same Network
Element(NE) and are within a single administrative private network
which is in close proximity.
o The FEs are already interconnected using Ethernet. We focus on
Ethernet because it is a very common setup as an FE interconnect.
While other higher transports (such as UDP over IP) or lower
transports could be defined to carry the data and metadata it is
simpler to use Ethernet (for the functional scope of a single
distributed device already interconnected with ethernet).
3.2. Sample Use Cases
To illustrate the problem scope we present two use cases where we
start with a single FE running all the LFBs functionality then split
it into multiple FEs achieving the same end goals.
3.2.1. Basic IPv4 Router
A sample LFB topology depicted in Figure 1 demonstrates a service
graph for delivering basic IPV4 forwarding service within one FE.
For the purpose of illustration, the diagram shows LFB classes as
graph nodes instead of multiple LFB class instances.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 4]
Internet-Draft ForCES Inter-FE LFB November 2015
Since the illustration on Figure 1 is meant only as an exercise to
showcase how data and metadata are sent down or upstream on a graph
of LFB instances, it abstracts out any ports in both directions and
talks about a generic ingress and egress LFB. Again, for
illustration purposes, the diagram does not show exception or error
paths. Also left out are details on Reverse Path Filtering, ECMP,
multicast handling etc. In other words, this is not meant to be a
complete description of an IPV4 forwarding application; for a more
complete example, please refer the LFBlib document [RFC6956].
The output of the ingress LFB(s) coming into the IPv4 Validator LFB
will have both the IPV4 packets and, depending on the implementation,
a variety of ingress metadata such as offsets into the different
headers, any classification metadata, physical and virtual ports
encountered, tunnelling information etc. These metadata are lumped
together as "ingress metadata".
Once the IPV4 validator vets the packet (example ensures that no
expired TTL etc), it feeds the packet and inherited metadata into the
IPV4 unicast LPM LFB.
+----+
| |
IPV4 pkt | | IPV4 pkt +-----+ +---+
+------------->| +------------->| | | |
| + ingress | | + ingress |IPv4 | IPV4 pkt | |
| metadata | | metadata |Ucast+------------>| +--+
| +----+ |LPM | + ingress | | |
+-+-+ IPv4 +-----+ + NHinfo +---+ |
| | Validator metadata IPv4 |
| | LFB NextHop|
| | LFB |
| | |
| | IPV4 pkt |
| | + {ingress |
+---+ + NHdetails}
Ingress metadata |
LFB +--------+ |
| Egress | |
<--+ |<-----------------+
| LFB |
+--------+
Figure 1: Basic IPV4 packet service LFB topology
The IPV4 unicast LPM LFB does a longest prefix match lookup on the
IPV4 FIB using the destination IP address as a search key. The
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 5]
Internet-Draft ForCES Inter-FE LFB November 2015
result is typically a next hop selector which is passed downstream as
metadata.
The Nexthop LFB receives the IPv4 packet with an associated next hop
info metadata. The NextHop LFB consumes the NH info metadata and
derives from it a table index to look up the next hop table in order
to find the appropriate egress information. The lookup result is
used to build the next hop details to be used downstream on the
egress. This information may include any source and destination
information (for our purposes, MAC addresses to use) as well as
egress ports. [Note: It is also at this LFB where typically the
forwarding TTL decrementing and IP checksum recalculation occurs.]
The details of the egress LFB are considered out of scope for this
discussion. Suffice it is to say that somewhere within or beyond the
Egress LFB the IPV4 packet will be sent out a port (Ethernet, virtual
or physical etc).
3.2.1.1. Distributing The Basic IPv4 Router
Figure 2 demonstrates one way the router LFB topology in Figure 1 may
be split across two FEs (eg two ASICs). Figure 2 shows the LFB
topology split across FEs after the IPV4 unicast LPM LFB.
FE1
+-------------------------------------------------------------+
| +----+ |
| +----------+ | | |
| | Ingress | IPV4 pkt | | IPV4 pkt +-----+ |
| | LFB +-------------->| +------------->| | |
| | | + ingress | | + ingress |IPv4 | |
| +----------+ metadata | | metadata |Ucast| |
| ^ +----+ |LPM | |
| | IPv4 +--+--+ |
| | Validator | |
| LFB | |
+---------------------------------------------------|---------+
|
IPv4 packet +
{ingress + NHinfo}
metadata
FE2 |
+---------------------------------------------------|---------+
| V |
| +--------+ +--------+ |
| | Egress | IPV4 packet | IPV4 | |
| <-----+ LFB |<----------------------+NextHop | |
| | |{ingress + NHdetails} | LFB | |
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 6]
Internet-Draft ForCES Inter-FE LFB November 2015
| +--------+ metadata +--------+ |
+-------------------------------------------------------------+
Figure 2: Split IPV4 packet service LFB topology
Some proprietary inter-connect (example Broadcom HiGig over XAUI
[brcm-higig]) are known to exist to carry both the IPV4 packet and
the related metadata between the IPV4 Unicast LFB and IPV4 NextHop
LFB across the two FEs.
This document defines the inter-FE LFB, a standard mechanism for
encapsulating, generating, receiving and decapsulating packets and
associated metadata FEs over Ethernet.
3.2.2. Arbitrary Network Function
In this section we show an example of an arbitrary Network Function
which is more coarse grained in terms of functionality. Each Network
Function may constitute more than one LFB.
FE1
+-------------------------------------------------------------+
| +----+ |
| +----------+ | | |
| | Network | pkt |NF2 | pkt +-----+ |
| | Function +-------------->| +------------->| | |
| | 1 | + NF1 | | + NF1/2 |NF3 | |
| +----------+ metadata | | metadata | | |
| ^ +----+ | | |
| | +--+--+ |
| | | |
| | |
+---------------------------------------------------|---------+
V
Figure 3: A Network Function Service Chain within one FE
The setup in Figure 3 is a typical of most packet processing boxes
where we have functions like DPI, NAT, Routing, etc connected in such
a topology to deliver a packet processing service to flows.
3.2.2.1. Distributing The Arbitrary Network Function
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 7]
Internet-Draft ForCES Inter-FE LFB November 2015
The setup in Figure 3 can be split out across 3 FEs instead of as
demonstrated in Figure 4. This could be motivated by scale out
reasons or because different vendors provide different functionality
which is plugged-in to provide such functionality. The end result is
to have the same packet service delivered to the different flows
passing through.
FE1 FE2
+----------+ +----+ FE3
| Network | pkt |NF2 | pkt +-----+
| Function +-------------->| +------------->| |
| 1 | + NF1 | | + NF1/2 |NF3 |
+----------+ metadata | | metadata | |
^ +----+ | |
| +--+--+
|
V
Figure 4: A Network Function Service Chain Distributed Across
Multiple FEs
4. Inter-FE LFB Overview
We address the inter-FE connectivity requirements by defining the
inter-FE LFB class. Using a standard LFB class definition implies no
change to the basic ForCES architecture in the form of the core LFBs
(FE Protocol or Object LFBs). This design choice was made after
considering an alternative approach that would have required changes
to both the FE Object capabilities (SupportedLFBs) as well
LFBTopology component to describe the inter-FE connectivity
capabilities as well as runtime topology of the LFB instances.
4.1. Inserting The Inter-FE LFB
The distributed LFB topology described in Figure 2 is re-illustrated
in Figure 5 to show the topology location where the inter-FE LFB
would fit in.
As can be observed in Figure 5, the same details passed between IPV4
unicast LPM LFB and the IPV4 NH LFB are passed to the egress side of
the Inter-FE LFB. This information is illustrated as multiplicity of
inputs into the egress InterFE LFB instance. Each input represents a
unique set of selection information.
FE1
+-------------------------------------------------------------+
| +----------+ +----+ |
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 8]
Internet-Draft ForCES Inter-FE LFB November 2015
| | Ingress | IPV4 pkt | | IPV4 pkt +-----+ |
| | LFB +-------------->| +------------->| | |
| | | + ingress | | + ingress |IPv4 | |
| +----------+ metadata | | metadata |Ucast| |
| ^ +----+ |LPM | |
| | IPv4 +--+--+ |
| | Validator | |
| | LFB | |
| | IPv4 pkt + metadata |
| | {ingress + NHinfo} |
| | | |
| | +..--+..+ |
| | |..| | | |
| +-V--V-V--V-+ |
| | Egress | |
| | InterFE | |
| | LFB | |
| +------+----+ |
+---------------------------------------------------|---------+
|
Ethernet Frame with: |
IPv4 packet data and metadata
{ingress + NHinfo + Inter FE info}
FE2 |
+---------------------------------------------------|---------+
| +..+.+..+ |
| |..|.|..| |
| +-V--V-V--V-+ |
| | Ingress | |
| | InterFE | |
| | LFB | |
| +----+------+ |
| | |
| IPv4 pkt + metadata |
| {ingress + NHinfo} |
| | |
| +--------+ +----V---+ |
| | Egress | IPV4 packet | IPV4 | |
| <-----+ LFB |<----------------------+NextHop | |
| | |{ingress + NHdetails} | LFB | |
| +--------+ metadata +--------+ |
+-------------------------------------------------------------+
Figure 5: Split IPV4 forwarding service with Inter-FE LFB
The egress of the inter-FE LFB uses the received packet and metadata
to select details for encapsulation when sending messages towards the
selected neighboring FE. These details include what to communicate
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 9]
Internet-Draft ForCES Inter-FE LFB November 2015
as the source and destination FEs (abstracted as MAC addresses as
described in Section 5.2); in addition the original metadata may be
passed along with the original IPV4 packet.
On the ingress side of the inter-FE LFB the received packet and its
associated metadata are used to decide the packet graph continuation.
This includes which of the original metadata and which next LFB class
instance to continue processing on. In the illustrated Figure 5, an
IPV4 Nexthop LFB instance is selected and appropriate metadata is
passed on to it.
The ingress side of the inter-FE LFB consumes some of the information
passed and passes on the IPV4 packet alongside with the ingress and
NHinfo metadata to the IPV4 NextHop LFB as was done earlier in both
Figure 1 and Figure 2.
5. Inter-FE Ethernet Connectivity
Section 5.1 describes some of the issues related to using Ethernet as
the transport and how we mitigate them.
Section 5.2 defines a payload format that is to be used over
Ethernet. An existing implementation of this specification on top of
Linux Traffic Control [linux-tc] is described in [tc-ife].
5.1. Inter-FE Ethernet Connectivity Issues
There are several issues that may occur due to using direct Ethernet
encapsulation that need consideration.
5.1.1. MTU Consideration
Because we are adding data to existing Ethernet frames, MTU issues
may arise. We recommend:
o To use large MTUs when possible (example with jumbo frames).
o Limit the amount of metadata that could be transmitted; our
definition allows for filtering of select metadata to be
encapsulated in the frame as described in Section 6. We recommend
sizing the egress port MTU so as to allow space for maximum size
of the metadata total size to allow between FEs. In such a setup,
the port is configured to "lie" to the upper layers by claiming to
have a lower MTU than it is capable of. MTU setting can be
achieved by ForCES control of the port LFB(or other config). In
essence, the control plane when explicitly making a decision for
the MTU settings of the egress port is implicitly deciding how
much metadata will be allowed.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 10]
Internet-Draft ForCES Inter-FE LFB November 2015
5.1.2. Quality Of Service Considerations
A raw packet arriving at the Inter-FE LFB (from upstream LFB Class
instances) may have COS metadatum indicating how it should be treated
from a Quality of Service perspective.
The resulting Ethernet frame will be eventually (preferentially)
treated by a downstream LFB(typically a port LFB instance) and their
COS marks will be honored in terms of priority. In other words the
presence of the Inter-FE LFB does not change the COS semantics
5.1.3. Congestion Considerations
The addition of the Inter-FE encapsulation adds overhead to the
packets and therefore bandwidth consumption on the wire. In cases
where Inter-FE encapsulated traffic shares wire resources with other
traffic, the new dynamics could potentially lead to congestion. In
such a case, given that the Inter-FE LFB is deployed within a single
administrative domain, the operator may need to enforce usage
restrictions. These restrictions may take the form of approriate
provisioning; example by rate limiting at an upstream LFB all Inter-
FE LFB traffic; or prioritizing non Inter-FE LFB traffic or other
techniques such as managed circuit breaking[circuit-b].
It is noted that a lot of the traffic passing through an FE that
utilizes the Inter-FE LFB is expected to be IP based which is
generally assumed to be congestion controlled and therefore does not
need addtional congestion control mechanisms[RFC5405].
5.1.4. Deployment Considerations
While we expect to use a unique IEEE-issued ethertype for the inter-
FE traffic, we use lessons learned from VXLAN deployment to be more
flexible on the settings of the ethertype value used. We make the
ether type an LFB read-write component. Linux VXLAN implementation
uses UDP port 8472 because the deployment happened much earlier than
the point of RFC publication where the IANA assigned udp port issued
was 4789 [vxlan-udp]. For this reason we make it possible to define
at control time what ethertype to use and default to the IEEE issued
ethertype. We justify this by assuming that a given ForCES NE is
likely to be owned by a single organization and that the
organization's CE(or CE cluster) could program all participating FEs
via the inter-FE LFB (described in this document) to recognize a
private Ethernet type used for inter-LFB traffic (possibly those
defined as available for private use by the IEEE, namely: IDs 0x88B5
and 0x88B6).
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 11]
Internet-Draft ForCES Inter-FE LFB November 2015
5.2. Inter-FE Ethernet Encapsulation
The Ethernet wire encapsulation is illustrated in Figure 6. The
process that leads to this encapsulation is described in Section 6.
The resulting frame is 32 bit aligned.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination MAC Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination MAC Address | Source MAC Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source MAC Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Inter-FE ethertype | Metadata length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV encoded Metadata ~~~..............~~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV encoded Metadata ~~~..............~~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Original packet data ~~................~~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: Packet format suggestion
The Ethernet header illustrated in Figure 6) has the following
semantics:
o The Destination MAC Address is used to identify the Destination
FEID by the CE policy (as described in Section 6).
o The Source MAC Address is used to identify the Source FEID by the
CE policy (as described in Section 6).
o The Ethernet type is used to identify the frame as inter-FE LFB
type. Ethertype 0xFEFE is to be used (XXX: Note to editor, likely
we wont get that value - update when available).
o The 16-bit metadata length is used to described the total encoded
metadata length (including the 16 bits used to encode the metadata
length).
o One or more 16-bit TLV encoded Metadatum follows the metadata
length field. The TLV type identifies the Metadata id. ForCES
IANA-defined Metadata ids will be used. All TLVs will be 32 bit
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 12]
Internet-Draft ForCES Inter-FE LFB November 2015
aligned. We recognize that using a 16 bit TLV restricts the
metadata id to 16 bits instead of ForCES-defined component ID
space of 32 bits. However, at the time of publication we believe
this is sufficient to carry all the info we need and approach
taken would save us 4 bytes per Metadatum transferred.
o The original packet data payload is appended at the end of the
metadata as shown.
6. Detailed Description of the Ethernet inter-FE LFB
The Ethernet inter-FE LFB has two LFB input port groups and three LFB
output ports as shown in Figure 7.
The inter-FE LFB defines two components used in aiding processing
described in Section 6.2.
+-----------------+
Inter-FE LFB | |
Encapsulated | OUT2+--> decapsulated Packet
-------------->|IngressInGroup | + metadata
Ethernet Frame | |
| |
raw Packet + | OUT1+--> Encapsulated Ethernet
-------------->|EgressInGroup | Frame
Metadata | |
| EXCEPTIONOUT +--> ExceptionID, packet
| | + metadata
+-----------------+
Figure 7: Inter-FE LFB
6.1. Data Handling
The Inter-FE LFB (instance) can be positioned at the egress of a
source FE. Figure 5 illustrates an example source FE in the form of
FE1. In such a case an Inter-FE LFB instance receives, via port
group EgressInGroup, a raw packet and associated metadata from the
preceding LFB instances. The input information is used to produce a
selection of how to generate and encapsulate the new frame. The set
of all selections is stored in the LFB component IFETable described
further below. The processed encapsulated Ethernet Frame will go out
on OUT1 to a downstream LFB instance when processing succeeds or to
the EXCEPTIONOUT port in the case of a failure.
The Inter-FE LFB (instance) can be positioned at the ingress of a
receiving FE. Figure 5 illustrates an example destination FE in the
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 13]
Internet-Draft ForCES Inter-FE LFB November 2015
form of FE1. In such a case an Inter-FE LFB receives, via an LFB
port in the IngressInGroup, an encapsulated Ethernet frame.
Successful processing of the packet will result in a raw packet with
associated metadata IDs going downstream to an LFB connected on OUT2.
On failure the data is sent out EXCEPTIONOUT.
6.1.1. Egress Processing
The egress Inter-FE LFB receives packet data and any accompanying
Metadatum at an LFB port of the LFB instance's input port group
labelled EgressInGroup.
The LFB implementation may use the incoming LFB port (within LFB port
group EgressInGroup) to map to a table index used to lookup the
IFETable table.
If lookup is successful, a matched table row which has the
InterFEinfo details is retrieved with the tuple {optional IFEtype,
optional StatId, Destination MAC address(DSTFE), Source MAC
address(SRCFE), optional metafilters}. The metafilters lists define
a whitelist of which Metadatum are to be passed to the neighboring
FE. The inter-FE LFB will perform the following actions using the
resulting tuple:
o Increment statistics for packet and byte count observed at
corresponding IFEStats entry.
o When MetaFilterList is present, then walk each received Metadatum
and apply against the MetaFilterList. If no legitimate metadata
is found that needs to be passed downstream then the processing
stops and send the packet and metadata out the EXCEPTIONOUT port
with exceptionID of EncapTableLookupFailed [RFC6956].
o Check that the additional overhead of the Ethernet header and
encapsulated metadata will not exceed MTU. If it does, increment
the error packet count statistics and send the packet and metadata
out the EXCEPTIONOUT port with exceptionID of FragRequired
[RFC6956].
o Create the Ethernet header
o Set the Destination MAC address of the Ethernet header with value
found in the DSTFE field.
o Set the Source MAC address of the Ethernet header with value found
in the SRCFE field.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 14]
Internet-Draft ForCES Inter-FE LFB November 2015
o If the optional IFETYPE is present, set the Ethernet type to the
value found in IFETYPE. If IFETYPE is absent then the standard
Inter-FE LFB Ethernet type is used (XXX: Note to editor, to be
updated).
o Encapsulate each allowed Metadatum in a TLV. Use the Metaid as
the "type" field in the TLV header. The TLV should be aligned to
32 bits. This means you may need to add padding of zeroes to
ensure alignment.
o Update the Metadata length to the sum of each TLV's space plus 2
bytes (for the Metadata length field 16 bit space).
The resulting packet is sent to the next LFB instance connected to
the OUT1 LFB-port; typically a port LFB.
In the case of a failed lookup the original packet and associated
metadata is sent out the EXCEPTIONOUT port with exceptionID of
EncapTableLookupFailed [RFC6956]. Note that the EXCEPTIONOUT LFB
port is merely an abstraction and implementation may in fact drop
packets as described above.
6.1.2. Ingress Processing
An ingressing inter-FE LFB packet is recognized by inspecting the
ethertype, and optionally the destination and source MAC addresses.
A matching packet is mapped to an LFB instance port in the
IngressInGroup. The IFETable table row entry matching the LFB
instance port may have optionally programmed metadata filters. In
such a case the ingress processing should use the metadata filters as
a whitelist of what metadatum is to be allowed.
o Increment statistics for packet and byte count observed.
o Look at the metadata length field and walk the packet data
extracting from the TLVs the metadata values. For each Metadatum
extracted, in the presence of metadata filters the metaid is
compared against the relevant IFETable row metafilter list. If
the Metadatum is recognized, and is allowed by the filter the
corresponding implementation Metadatum field is set. If an
unknown Metadatum id is encountered, or if the metaid is not in
the allowed filter list the implementation is expected to ignore
it, increment the packet error statistic and proceed processing
other Metadatum.
o Upon completion of processing all the metadata, the inter-FE LFB
instance resets the data point to the original payload i.e skips
the IFE header information. At this point the original packet
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 15]
Internet-Draft ForCES Inter-FE LFB November 2015
that was passed to the egress Inter-FE LFB at the source FE is
reconstructed. This data is then passed along with the
reconstructed metadata downstream to the next LFB instance in the
graph.
In the case of processing failure of either ingress or egress
positioning of the LFB, the packet and metadata are sent out the
EXCEPTIONOUT LFB port with appropriate error id. Note that the
EXCEPTIONOUT LFB port is merely an abstraction and implementation may
in fact drop packets as described above.
6.2. Components
There are two LFB components accessed by the CE. The reader is asked
to refer to the definitions in Figure 8.
The first component, populated by the CE, is an array known as the
IFETable table. The array rows are made up of IFEInfo structure.
The IFEInfo structure constitutes: optional IFETYPE, optionally
present StatId, Destination MAC address(DSTFE), Source MAC
address(SRCFE), optionally present array of allowed Metaids
(MetaFilterList).
The second component(ID 2), populated by the FE and read by the CE,
is an indexed array known as the IFEStats table. Each IFEStats row
which carries statistics information in the structure bstats.
A note about the StatId relationship between the IFETable table and
IFEStats table: An implementation may choose to map between an
IFETable row and IFEStats table row using the StatId entry in the
matching IFETable row. In that case the IFETable StatId must be
present. Alternative implementation may map at provisioning time an
IFETable row to IFEStats table row. Yet another alternative
implementation may choose not to use the IFETable row StatId and
instead use the IFETable row index as the IFEStats index. For these
reasons the StatId component is optional.
6.3. Inter-FE LFB XML Model
<LFBLibrary xmlns="urn:ietf:params:xml:ns:forces:lfbmodel:1.1"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
provides="IFE">
<frameDefs>
<frameDef>
<name>PacketAny</name>
<synopsis>Arbitrary Packet</synopsis>
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 16]
Internet-Draft ForCES Inter-FE LFB November 2015
</frameDef>
<frameDef>
<name>InterFEFrame</name>
<synopsis>
Ethernet Frame with encapsulate IFE information
</synopsis>
</frameDef>
</frameDefs>
<dataTypeDefs>
<dataTypeDef>
<name>bstats</name>
<synopsis>Basic stats</synopsis>
<struct>
<component componentID="1">
<name>bytes</name>
<synopsis>The total number of bytes seen</synopsis>
<typeRef>uint64</typeRef>
</component>
<component componentID="2">
<name>packets</name>
<synopsis>The total number of packets seen</synopsis>
<typeRef>uint32</typeRef>
</component>
<component componentID="3">
<name>errors</name>
<synopsis>The total number of packets with errors</synopsis>
<typeRef>uint32</typeRef>
</component>
</struct>
</dataTypeDef>
<dataTypeDef>
<name>IFEInfo</name>
<synopsis>Describing IFE table row Information</synopsis>
<struct>
<component componentID="1">
<name>IFETYPE</name>
<synopsis>
the ethernet type to be used for outgoing IFE frame
</synopsis>
<optional/>
<typeRef>uint16</typeRef>
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 17]
Internet-Draft ForCES Inter-FE LFB November 2015
</component>
<component componentID="2">
<name>StatId</name>
<synopsis>
the Index into the stats table
</synopsis>
<optional/>
<typeRef>uint32</typeRef>
</component>
<component componentID="3">
<name>DSTFE</name>
<synopsis>
the destination MAC address of destination FE
</synopsis>
<typeRef>byte[6]</typeRef>
</component>
<component componentID="4">
<name>SRCFE</name>
<synopsis>
the source MAC address used for the source FE
</synopsis>
<typeRef>byte[6]</typeRef>
</component>
<component componentID="5">
<name>MetaFilterList</name>
<synopsis>
the allowed metadata filter table
</synopsis>
<optional/>
<array type="variable-size">
<typeRef>uint32</typeRef>
</array>
</component>
</struct>
</dataTypeDef>
</dataTypeDefs>
<LFBClassDefs>
<LFBClassDef LFBClassID="18">
<name>IFE</name>
<synopsis>
This LFB describes IFE connectivity parameterization
</synopsis>
<version>1.0</version>
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 18]
Internet-Draft ForCES Inter-FE LFB November 2015
<inputPorts>
<inputPort group="true">
<name>EgressInGroup</name>
<synopsis>
The input port group of the egress side.
It expects any type of Ethernet frame.
</synopsis>
<expectation>
<frameExpected>
<ref>PacketAny</ref>
</frameExpected>
</expectation>
</inputPort>
<inputPort group="true">
<name>IngressInGroup</name>
<synopsis>
The input port group of the ingress side.
It expects an interFE encapsulated Ethernet frame.
</synopsis>
<expectation>
<frameExpected>
<ref>InterFEFrame</ref>
</frameExpected>
</expectation>
</inputPort>
</inputPorts>
<outputPorts>
<outputPort>
<name>OUT1</name>
<synopsis>
The output port of the egress side.
</synopsis>
<product>
<frameProduced>
<ref>InterFEFrame</ref>
</frameProduced>
</product>
</outputPort>
<outputPort>
<name>OUT2</name>
<synopsis>
The output port of the Ingress side.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 19]
Internet-Draft ForCES Inter-FE LFB November 2015
</synopsis>
<product>
<frameProduced>
<ref>PacketAny</ref>
</frameProduced>
</product>
</outputPort>
<outputPort>
<name>EXCEPTIONOUT</name>
<synopsis>
The exception handling path
</synopsis>
<product>
<frameProduced>
<ref>PacketAny</ref>
</frameProduced>
<metadataProduced>
<ref>ExceptionID</ref>
</metadataProduced>
</product>
</outputPort>
</outputPorts>
<components>
<component componentID="1" access="read-write">
<name>IFETable</name>
<synopsis>
the table of all InterFE relations
</synopsis>
<array type="variable-size">
<typeRef>IFEInfo</typeRef>
</array>
</component>
<component componentID="2" access="read-only">
<name>IFEStats</name>
<synopsis>
the stats corresponding to the IFETable table
</synopsis>
<typeRef>bstats</typeRef>
</component>
</components>
</LFBClassDef>
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 20]
Internet-Draft ForCES Inter-FE LFB November 2015
</LFBClassDefs>
</LFBLibrary>
Figure 8: Inter-FE LFB XML
7. Acknowledgements
The authors would like to thank Joel Halpern and Dave Hood for the
stimulating discussions. Evangelos Haleplidis shepherded and
contributed to improving this document. Alia Atlas was the AD
sponsor of this document and did a tremendous job of critiquing it.
The authors are grateful to Joel Halpern in his role as the Routing
Area reviewer in shaping the content of this document.
8. IANA Considerations
This memo includes one IANA requests within the registry https://
www.iana.org/assignments/forces
The request is for the sub-registry "Logical Functional Block (LFB)
Class Names and Class Identifiers" to request for the reservation of
LFB class name IFE with LFB classid 18 with version 1.0.
+--------------+---------+---------+-------------------+------------+
| LFB Class | LFB | LFB | Description | Reference |
| Identifier | Class | Version | | |
| | Name | | | |
+--------------+---------+---------+-------------------+------------+
| 18 | IFE | 1.0 | An IFE LFB to | This |
| | | | standardize | document |
| | | | inter-FE LFB for | |
| | | | ForCES Network | |
| | | | Elements | |
+--------------+---------+---------+-------------------+------------+
Logical Functional Block (LFB) Class Names and Class Identifiers
9. IEEE Assignment Considerations
This memo includes a request for a new ethernet protocol type as
described in Section 5.2.
10. Security Considerations
The FEs involved in the Inter-FE LFB belong to the same Network
Device (NE) and are within the scope of a single administrative
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 21]
Internet-Draft ForCES Inter-FE LFB November 2015
Ethernet LAN private network. Trust of policy in the control and its
treatment in the datapath exists already.
This document does not alter [RFC5812] or the ForCES
Protocol[RFC5810]. As such, it has no impact on their security
considerations. This document simply defines the operational
parameters and capabilities of an LFB that performs LFB class
instance extensions across nodes under a single administrative
control. This document does not attempt to analyze the presence or
possibility of security interactions created by allowing LFB graph
extension on packets. Any such issues, if they exist should be
resolved by the designers of the particular data path i.e they are
not the responsibility of general mechanism outlined in this
document; one such option for protecting Ethernet is the use of IEEE
802.1AE Media Access Control Security [ieee8021ae] which provides
encryption and authentication.
11. References
11.1. Normative References
[RFC5810] Doria, A., Ed., Hadi Salim, J., Ed., Haas, R., Ed.,
Khosravi, H., Ed., Wang, W., Ed., Dong, L., Gopal, R., and
J. Halpern, "Forwarding and Control Element Separation
(ForCES) Protocol Specification", RFC 5810, DOI 10.17487/
RFC5810, March 2010,
<http://www.rfc-editor.org/info/rfc5810>.
[RFC5811] Hadi Salim, J. and K. Ogawa, "SCTP-Based Transport Mapping
Layer (TML) for the Forwarding and Control Element
Separation (ForCES) Protocol", RFC 5811, DOI 10.17487/
RFC5811, March 2010,
<http://www.rfc-editor.org/info/rfc5811>.
[RFC5812] Halpern, J. and J. Hadi Salim, "Forwarding and Control
Element Separation (ForCES) Forwarding Element Model", RFC
5812, DOI 10.17487/RFC5812, March 2010,
<http://www.rfc-editor.org/info/rfc5812>.
[RFC7391] Hadi Salim, J., "Forwarding and Control Element Separation
(ForCES) Protocol Extensions", RFC 7391, DOI 10.17487/
RFC7391, October 2014,
<http://www.rfc-editor.org/info/rfc7391>.
[RFC7408] Haleplidis, E., "Forwarding and Control Element Separation
(ForCES) Model Extension", RFC 7408, DOI 10.17487/RFC7408,
November 2014, <http://www.rfc-editor.org/info/rfc7408>.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 22]
Internet-Draft ForCES Inter-FE LFB November 2015
11.2. Informative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC3746] Yang, L., Dantu, R., Anderson, T., and R. Gopal,
"Forwarding and Control Element Separation (ForCES)
Framework", RFC 3746, DOI 10.17487/RFC3746, April 2004,
<http://www.rfc-editor.org/info/rfc3746>.
[RFC5405] Eggert, L. and G. Fairhurst, "Unicast UDP Usage Guidelines
for Application Designers", BCP 145, RFC 5405, DOI
10.17487/RFC5405, November 2008,
<http://www.rfc-editor.org/info/rfc5405>.
[RFC6956] Wang, W., Haleplidis, E., Ogawa, K., Li, C., and J.
Halpern, "Forwarding and Control Element Separation
(ForCES) Logical Function Block (LFB) Library", RFC 6956,
DOI 10.17487/RFC6956, June 2013,
<http://www.rfc-editor.org/info/rfc6956>.
[brcm-higig]
, "HiGig",
<http://www.broadcom.com/products/brands/HiGig>.
[circuit-b]
Fairhurst, G., "Network Transport Circuit Breakers", Sep
2015, <https://tools.ietf.org/html/draft-fairhurst-tsvwg-
circuit-breaker-04>.
[ieee8021ae]
, "IEEE Standard for Local and metropolitan area networks
Media Access Control (MAC) Security", IEEE 802.1AE-2006,
Aug 2006.
[linux-tc]
Hadi Salim, J., "Linux Traffic Control Classifier-Action
Subsystem Architecture", netdev 01, Feb 2015.
[tc-ife] Hadi Salim, J. and D. Joachimpillai, "Distributing Linux
Traffic Control Classifier-Action Subsystem", netdev 01,
Feb 2015.
[vxlan-udp]
, "iproute2 and kernel code (drivers/net/vxlan.c)",
<https://www.kernel.org/pub/linux/utils/net/iproute2/>.
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 23]
Internet-Draft ForCES Inter-FE LFB November 2015
Authors' Addresses
Damascane M. Joachimpillai
Verizon
60 Sylvan Rd
Waltham, Mass. 02451
USA
Email: damascene.joachimpillai@verizon.com
Jamal Hadi Salim
Mojatatu Networks
Suite 200, 15 Fitzgerald Rd.
Ottawa, Ontario K2H 9G1
Canada
Email: hadi@mojatatu.com
Joachimpillai & Hadi Salim Expires May 5, 2016 [Page 24]