Skip to main content

The Accumulated IGP Metric Attribute for BGP
draft-ietf-idr-aigp-12

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 7311.
Authors Prodosh Mohapatra , Rex Fernando , Eric C. Rosen , Jim Uttaro
Last updated 2013-11-22
Replaces draft-rosen-idr-aigp
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Waiting for WG Chair Go-Ahead
Revised I-D Needed - Issue raised by WGLC
Document shepherd Susan Hares
IESG IESG state Became RFC 7311 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-idr-aigp-12
Network Working Group                                  Pradosh Mohapatra
Internet Draft                                          Cumulus Networks
Intended Status: Proposed Standard
Expires: May 22, 2014                                       Rex Fernando
                                                           Eric C. Rosen
                                                     Cisco Systems, Inc.

                                                            James Uttaro
                                                                     ATT

                                                       November 22, 2013

              The Accumulated IGP Metric Attribute for BGP

                       draft-ietf-idr-aigp-12.txt

Abstract

   Routing protocols that have been designed to run within a single
   administrative domain ("IGPs") generally do so by assigning a metric
   to each link, and then choosing as the installed path between two
   nodes the path for which the total distance (sum of the metric of
   each link along the path) is minimized.  BGP, designed to provide
   routing over a large number of independent administrative domains
   ("autonomous systems"), does not make its path selection decisions
   through the use of a metric.  It is generally recognized that any
   attempt to do so would incur significant scalability problems, as
   well as inter-administration coordination problems.  However, there
   are deployments in which a single administration runs several
   contiguous BGP networks.  In such cases, it can be desirable, within
   that single administrative domain, for BGP to select paths based on a
   metric, just as an IGP would do.  The purpose of this document is to
   provide a specification for doing so.

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

Mohapatra, et al.                                               [Page 1]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

Copyright and License Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document. Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Mohapatra, et al.                                               [Page 2]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

Table of Contents

 1          Specification of requirements  .........................   3
 2          Introduction  ..........................................   3
 3          AIGP Attribute  ........................................   5
 3.1        Applicability Restrictions and Cautions  ...............   6
 3.2        Handling a Malformed AIGP Attribute  ...................   6
 3.3        Restrictions on Sending/Receiving  .....................   7
 3.4        Creating and Modifying the AIGP Attribute  .............   7
 3.4.1      Originating the AIGP Attribute  ........................   7
 3.4.2      Modifications by the Originator  .......................   9
 3.4.3      Modifications by a Non-Originator  .....................   9
 4          Decision Process  ......................................  11
 4.1        When a Route has an AIGP Attribute  ....................  11
 4.2        When the Route to the Next Hop has an AIGP attribute  ..  12
 5          Deployment Considerations  .............................  12
 6          IANA Considerations  ...................................  13
 7          Security Considerations  ...............................  13
 8          Acknowledgments  .......................................  13
 9          Authors' Addresses  ....................................  13
10          Normative References  ..................................  14
11          Informative References  ................................  14

1. Specification of requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2. Introduction

   There are many routing protocols that have been designed to run
   within a single administrative domain.  These are known collectively
   as "Interior Gateway Protocols" (IGPs).  Typically, each link is
   assigned a particular "metric" value.  The path between two nodes can
   then be assigned a "distance", which is the sum of the metrics of all
   the links that belong to that path.  An IGP selects the "shortest"
   (minimal distance) path between any two nodes, perhaps subject to the
   constraint that if the IGP provides multiple "areas", it may prefer
   the shortest path within an area to a path that traverses more than

Mohapatra, et al.                                               [Page 3]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

   one area.  Typically the administration of the network has some
   routing policy which can be approximated by selecting shortest paths
   in this way.

   BGP, as distinguished from the IGPs, was designed to run over an
   arbitrarily large number of administrative domains ("autonomous
   systems", or "ASes") with limited coordination among the various
   administrations.  BGP does not make its path selection decisions
   based on a metric; there is no such thing as an "inter-AS metric".
   There are two fundamental reasons for this:

     - The distance between two nodes in a common administrative domain
       may change at any time due to events occurring in that domain.
       These changes are not propagated around the Internet unless they
       actually cause the border routers of the domain to select routes
       with different BGP attributes for some set of address prefixes.
       This accords with a fundamental principle of scaling, viz., that
       changes with only local significance must not have global
       effects.  If local changes in distance were always propagated
       around the Internet, this principle would be violated.

     - A basic principle of inter-domain routing is that the different
       administrative domains may have their own policies, which do not
       have to be revealed to other domains, and which certainly do not
       have to be agreed to by other domains.  Yet the use of inter-AS
       metric in the Internet would have exactly these effects.

   There are, however, deployments in which a single administration runs
   a network which has been sub-divided into multiple, contiguous ASes,
   each running BGP.  There are several reasons why a single
   administrative domain may be broken into several ASes (which, in this
   case, are not really "autonomous".)  It may be that the existing IGPs
   do not scale well in the particular environment; it may be that a
   more generalized topology is desired than could be obtained by use of
   a single IGP domain; it may be that a more finely grained routing
   policy is desired than can be supported by an IGP.  In such
   deployments, it can be useful to allow BGP to make its routing
   decisions based on the IGP metric, so that BGP chooses the "shortest"
   path between two nodes, even if the nodes are in two different ASes
   within that same administrative domain.  We will refer to the set of
   ASes in a common administrative domain as an "AIGP Administrative
   Domain".

   There are in fact some implementations that already do something like
   this, using BGP's MULTI_EXIT_DISC (MED) attribute to carry a value
   based on IGP metrics.  However, that doesn't really provide IGP-like
   "shortest path" routing, as the BGP decision process gives priority
   to other factors, such as the AS_PATH length.  Also, the standard

Mohapatra, et al.                                               [Page 4]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

   procedures for use of the MED do not ensure that the IGP metric is
   properly accumulated so that it covers all the links along the path.

   In this document, we define a new optional, non-transitive BGP
   attribute, called the "Accumulated IGP Metric Attribute", or "AIGP
   attribute", and specify the procedures for using it.

   The specified procedures prevent the AIGP attribute from "leaking
   out" past an AIGP administrative domain boundary into the Internet.

   The specified procedures also ensure that the value in the AIGP
   attribute has been accumulated all along the path from the
   destination, i.e., that the AIGP attribute does not appear when there
   are "gaps" along the path where the IGP metric is unknown.

3. AIGP Attribute

   The AIGP Attribute is an optional non-transitive BGP Path Attribute.
   The attribute type code for the AIGP Attribute is 26.

   The value field of the AIGP Attribute is defined here to be a set of
   elements encoded as "Type/Length/Value" (i.e., a set of "TLVs").
   Each such TLV is encoded as shown in Figure 1.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     Type      |         Length                |               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+               |
       ~                                                               ~
       |                           Value                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+..........................

                                 AIGP TLV
                                 Figure 1

    - Type: A single octet encoding the TLV Type.  Only type 1, "AIGP
      TLV", is defined in this document.  Use of other TLV types is
      outside the scope of this document.

    - Length: Two octets encoding the length in octets of the TLV,
      including the type and length fields.  The length is encoded as an
      unsigned binary integer.  (Note that the minimum length is 3,
      indicating that no value field is present.)

Mohapatra, et al.                                               [Page 5]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

    - A value field containing zero or more octets.

  This document defines only a single such TLV, the "AIGP TLV".  The
  AIGP TLV is encoded as follows:

    - Type: 1

    - Length: 11

    - Accumulated IGP Metric.

      The value field of the AIGP TLV is always 8 bytes long.  IGP
      metrics are frequently expressed as 4-octet values, and this
      ensures that the AIGP attribute can be used to hold the sum of an
      arbitrary number of 4-octet values.

  When an AIGP attribute is created, it SHOULD contain no more than one
  AIGP TLV.  However, if it contains more than one AIGP TLV, only the
  first one is is used as described in Section 3.4 and Section 4.  In
  the remainder of this document, we will use the term "value of the
  AIGP TLV" to mean the value of the first AIGP TLV in the AIGP
  attribute.  Any other AIGP TLVs in the AIGP attribute MUST be passed
  along unchanged if the AIGP attribute is passed along.

3.1. Applicability Restrictions and Cautions

   This document only considers the use of the AIGP attribute in
   networks where each router uses tunneling of some sort to deliver a
   packet to its BGP next hop.  Use of the AIGP attribute in networks
   that do not use tunneling is outside the scope of this document.

   If a Route Reflector supports the AIGP attribute, but some of its
   clients do not, then the routing choices that result may not all
   reflect the intended routing policy.

3.2. Handling a Malformed AIGP Attribute

   When receiving a BGP Update message containing a malformed AIGP
   attribute, the attribute MUST be treated exactly as if it were an
   unrecognized non-transitive attribute.  That is, "it MUST be quietly
   ignored and not passed along to other BGP peers".  This is equivalent
   to the "attribute discard" action specified in [BGP-ERROR].

   Note that an AIGP attribute MUST NOT be considered to be malformed
   because it contains more than one TLV of a given type, or because it

Mohapatra, et al.                                               [Page 6]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

   contains TLVs of unknown types.

   If a BGP Path Attribute is received that has the AIGP attribute
   codepoint, but also has the transitive bit set, the attribute MUST be
   considered to be a malformed AIGP attribute, and MUST be discarded as
   specified in this section.

   If an AIGP attribute is received, and its first AIGP TLV contains the
   maximum value 0xffffffffffffffff, the attribute SHOULD be considered
   to be malformed, and discarded as specified in this section.  (Since
   the TLV value cannot be increased any further, it is not useful for
   metric-based path selection.)

3.3. Restrictions on Sending/Receiving

   An implementation that supports the AIGP attribute MUST support a
   per-session configuration item, AIGP_SESSION, that indicates whether
   the attribute is enabled or disabled for use on that session.

     - The default value of AIGP_SESSION, for EBGP sessions, MUST be
       "disabled".

     - The default value of AIGP_SESSION, for IBGP and confederation-
       EBGP sessions, SHOULD be "enabled."

   The AIGP attribute MUST NOT be sent on any BGP session for which
   AIGP_SESSION is disabled.

   If an AIGP attribute is received on a BGP session for which
   AIGP_SESSION is disabled, the attribute MUST be treated exactly as if
   it were an unrecognized non-transitive attribute.  That is, "it MUST
   be quietly ignored and not passed along to other BGP peers" (see
   [BGP], section 5).

3.4. Creating and Modifying the AIGP Attribute

3.4.1. Originating the AIGP Attribute

   An implementation that supports the AIGP attribute MUST support a
   configuration item, AIGP_ORIGINATE, that enables or disables its
   creation and attachment to routes.  The default value of
   AIGP_ORIGINATE MUST be "disabled".

   A BGP speaker MUST NOT add the AIGP attribute to any route whose path
   leads outside the "AIGP administrative domain" to which the BGP
   speaker belongs.  It may be added only to routes that satisfy one of

Mohapatra, et al.                                               [Page 7]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

   the following conditions:

     - The route is a static route that is being redistributed into BGP

     - The route is an IGP route that is being redistributed into BGP

     - The route is an IBGP-learned route whose AS_PATH attribute is
       empty.

     - The route is an EBGP-learned route whose AS_PATH contains only
       ASes that are in the same AIGP Administrative Domain as the BGP
       speaker.

   A BGP speaker R MUST NOT add the AIGP attribute to any route for
   which R does not set itself as the next hop.

   It SHOULD be possible to set AIGP_ORIGINATE to "enabled for the
   routes of a particular IGP that are redistributed into BGP" (where "a
   particular IGP" might be "OSPF" or "ISIS").  Other policies
   determining when and whether to originate an AIGP attribute are also
   possible, depending on the needs of a particular deployment scenario.

   When originating an AIGP attribute for a BGP route to address prefix
   P, the value of the AIGP TLV is set according to policy.  There are a
   number of useful policies, some of which are in the following list:

     - When a BGP speaker R is redistributing into BGP an IGP route to
       address prefix P, the IGP will have computed a "distance" from R
       to P.  This distance MAY be assigned as the value of the AIGP
       TLV.

     - A BGP speaker R may be redistributing into BGP a static route to
       address prefix P, for which a "distance" from R to P has been
       configured.  This distance MAY be assigned as the value of the
       AIGP TLV.

     - A BGP speaker R may have received and installed a BGP-learned
       route to prefix P, with next hop N.  Or it may be redistributing
       a static route to P, with next hop N.  Then:

         * If R has an IGP route to N, the IGP-computed distance from R
           to N MAY be used as the value of the AIGP TLV of the route to
           P.

         * If R has a BGP route to N, and an AIGP TLV attribute value
           has been computed for that route (see section 3.4.3), that
           value MAY be used as the AIGP TLV value of the route to P.

Mohapatra, et al.                                               [Page 8]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

3.4.2. Modifications by the Originator

   If BGP speaker R is the originator of the AIGP attribute of prefix P,
   and at some point the "distance" from R to P changes, R SHOULD issue
   a new BGP update containing the new value of the AIGP TLV of the AIGP
   attribute.  (Here we use the term "distance" to refer to whatever
   value the originator assigns to the AIGP TLV, however it is computed;
   see section 3.4.1.) However, if the difference between the new
   distance and the distance advertised in the AIGP TLV is less than a
   configurable threshold, the update MAY be suppressed.

3.4.3. Modifications by a Non-Originator

   Suppose a BGP speaker R1 receives a route with an AIGP attribute
   whose value is A, and a Next Hop whose value is R2.  Suppose also
   that R1 is about to redistribute that route on a BGP session that is
   enabled for sending/receiving the attribute.

   If R1 does not change the Next Hop of the route, then R1 MUST NOT
   change the AIGP attribute value of the route.

   In all the computations discussed in this section, the AIGP value
   MUST be capped at its maximum unsigned value 0xffffffffffffffff.
   Increasing the AIGP value MUST NOT cause the value to wrap around.

   If R1 changes the Next Hop of the route from R2 to R1, and if R1's
   route to R2 is an IGP-learned route, or a static route that does not
   require recursive next hop resolution, then R1 MUST increase the
   value of the AIGP TLV by adding to A the distance from R1 to R2.
   This distance is either the IGP-computed distance from R1 to R2, or
   some value determined by policy.  However, A MUST be increased by a
   non-zero amount.

   Note that if R1 and R2 above are EBGP neighbors, and there is a
   direct link between them on which no IGP is running, then when R1
   changes the next hop of a route from R2 to R1, the AIGP TLV value
   MUST be increased by a non-zero amount.  The amount of the increase
   SHOULD be such that it is properly comparable to the IGP metrics.
   E.g., if the IGP metric is a function of latency, then the amount of
   the increase should be a function of the latency from R1 to R2.

   If R1 changes the Next Hop of the route from R2 to R1, and if R1's
   route to R2 is a BGP-learned route, or a static route that requires
   recursive next hop resolution, then the AIGP TLV value needs to be
   increased in several steps, according to the following procedure.
   (Note that this procedure is ONLY used when recursive next hop
   resolution is needed.)

Mohapatra, et al.                                               [Page 9]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

      1. Let Xattr be the new AIGP TLV value.

      2. Initialize Xattr to A.

      3. Set the XNH to R2.

      4. Find the route to XNH.

      5. If the route to XNH does not require recursive next hop
         resolution, get the distance D from R1 to XNH.  (Note that this
         condition cannot be satisfied the first time through this
         procedure.)  If D is above a configurable threshold, set the
         AIGP TLV value to Xattr+D.  If D is below a configurable
         threshold, set the AIGP TLV value to Xattr.  In either case,
         exit this procedure.

      6. If the route to XNH is a BGP-learned route, and the route does
         NOT have an AIGP attribute, then exit this procedure and do not
         pass on any AIGP attribute.  If the route has an AIGP attribute
         without an AIGP TLV, then the AIGP attribute MAY be passed
         along unchanged.

      7. If the route to XNH is a BGP-learned route, and the route has
         an AIGP TLV value of Y, then set Xattr=Xattr+Y, and set XNH to
         the next hop of this route.  (The intention here is that Y is
         the AIGP TLV value of the route as it was received by R1,
         without having been modified by R1.)

      8. Go to step 4.

   The AIGP TLV value of a given route depends on (a) the AIGP TLV
   values of all the next hops that are recursively resolved during this
   procedure, and (b) the IGP distance to any next hop that is not
   recursively resolved.  Any change due to (a) in any of these values
   MUST trigger a new AIGP computation for that route.  Whether a change
   due to (b) triggers a new AIGP computation depends upon whether the
   change in IGP distance exceeds a configurable threshold.

   If the AIGP attribute is carried across several ASes, each with its
   own IGP domain, it is clear that these procedures are unlikely to
   give a sensible result if the IGPs are different (e.g., some OSPF and
   some IS-IS), or if the meaning of the metrics is different in the
   different IGPs (e.g., if the metric represents bandwidth in some IGP
   domains but represents latency in others). These procedures also are
   unlikely to give a sensible result if the metric assigned to inter-AS
   BGP links (on which no IGP is running) or to static routes is not
   comparable to the IGP metrics.  All such cases are outside the scope
   of the current document.

Mohapatra, et al.                                              [Page 10]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

4. Decision Process

   Support for the AIGP attribute involves several modifications to the
   tie breaking procedures of the BGP "phase 2" decision described in
   [BGP], section 9.1.2.2.  These modifications are described below in
   sections 4.1 and 4.2.

   In some cases, the BGP decision process may install a route without
   executing any tie breaking procedures.  This may happen, e.g., if
   only one route to a given prefix has the highest degree of preference
   (as defined in [BGP] section 9.1.1).  In this case, the AIGP
   attribute is not considered.

   In other cases, some routes may be eliminated before the tie breaking
   procedures are invoked, e.g., routes with AS-PATH attributes
   indicating a loop, or routes with unresolvable next hops.  In these
   cases, the AIGP attributes of the eliminated routes are not
   considered.

4.1. When a Route has an AIGP Attribute

   Assuming that the BGP decision process invokes the tie breaking
   procedures, the procedures in this section MUST be executed BEFORE
   any of the tie breaking procedures described in [BGP] section 9.1.2.2
   are executed.

   If any routes have an AIGP attribute containing an AIGP TLV, remove
   from consideration all routes that do not have an AIGP attribute
   containing an AIGP TLV.

   If router R is considering route T, where T has an AIGP attribute
   with an AIGP TLV,

     - then R must compute the value A, defined as follows: set A to the
       sum of (a) T's AIGP TLV value and (b) the IGP distance from R to
       T's next hop.

     - remove from consideration all routes that are not tied for the
       lowest value of A.

Mohapatra, et al.                                              [Page 11]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

4.2. When the Route to the Next Hop has an AIGP attribute

   Suppose that a given router R1 is comparing two BGP-learned routes,
   such that either:

     - the two routes have equal AIGP TLV values, or else

     - neither of the two routes has an AIGP attribute containing an
       AIGP TLV.

   The BGP decision process as specified in [BGP] makes use, in its tie
   breaker procedures, of "interior cost", defined as follows:

       "interior cost of a route is determined by calculating the metric
       to the NEXT_HOP for the route using the Routing Table."

   Suppose route T has a next hop of N.  We modify the notion of the
   "interior cost" from node R1 to node N as follows:

     - Let R2 be the BGP next hop of the route to N, after all recursive
       resolution of the next hop is done.  Let m be the IGP distance
       (or in the case of a static route, the configured distance) from
       R1 to R2.

     - If the installed route to N has an AIGP attribute with an AIGP
       TLV, set A to the AIGP value of the route to N, computing the
       AIGP value of the route according to the procedure of section
       3.4.3.

     - If the installed route to N does not have an AIGP value, set A to
       0.

     - The "interior cost" of route T is the quantity A+m.

5. Deployment Considerations

   Using the AIGP attribute to achieve a desired routing policy will be
   more effective if each BGP speaker can use it to choose from among
   multiple routes. Thus is it highly recommended that the procedures of
   [BESTEXT] and [CONN-REST] be used in conjunction with the AIGP
   Attribute.

   If a Route Reflector does not pass all paths to its clients, then it
   will tend to pass the paths for which the IGP distance from the Route
   Reflector itself to the next hop is smallest.  This may result in a
   non-optimal choice by the clients.

Mohapatra, et al.                                              [Page 12]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

6. IANA Considerations

   IANA has assigned the codepoint 26 in the "BGP Path Attributes"
   registry to the AIGP attribute.

   IANA shall create a registry for "BGP AIGP Attribute Types".  The
   type field consists of a single octet, with possible values from 0 to
   255.  The allocation policy for this field is to be "Standards Action
   with Early Allocation".  Type 1 should be defined as "AIGP", and
   should refer to this document.

7. Security Considerations

   The spurious introduction, though error or malfeasance, of an AIGP
   attribute, could result in the selection of paths other than those
   desired.

   Improper configuration on both ends of an EBGP connection could
   result in an AIGP attribute being passed from one service provider to
   another.  This would likely result in an unsound selection of paths.

8. Acknowledgments

   The authors would like to thank Waqas Alam, Rajiv Asati, Brian
   Dickson, Clarence Filsfils, Anoop Kapoor, Pratima Kini, Thomas
   Mangin, Robert Raszuk, Yakov Rekhter, Eric Rosenberg, Samir Saad,
   John Scudder, Shyam Sethuram, and Ilya Varlashkin for their input.

9. Authors' Addresses

   Rex Fernando
   Cisco Systems, Inc.
   170 Tasman Drive
   San Jose, CA  95134
   Email: rex@cisco.com

   Pradosh Mohapatra
   Cumulus Networks
   Email: pmohapat@cumulusnetworks.com

Mohapatra, et al.                                              [Page 13]



Internet Draft         draft-ietf-idr-aigp-12.txt          November 2013

   Eric C. Rosen
   Cisco Systems, Inc.
   1414 Massachusetts Avenue
   Boxborough, MA, 01719
   Email: erosen@cisco.com

   James Uttaro
   AT&T
   200 S. Laurel Avenue
   Middletown, NJ 07748
   Email: uttaro@att.com

10. Normative References

   [BGP], "A Border Gateway Protocol 4 (BGP-4)", Y. Rekhter, T. Li, S.
   Hares, RFC 4271, January 2006.

11. Informative References

   [CONN-REST] "Fast Connectivity Restoration Using BGP Add-Path", P.
   Mohapatra, R. Fernando, C. Filsfils, R. Raszuk, draft-pmohapat-idr-
   fast-conn-restore-03.txt, January 2013.

   [BESTEXT], "Advertisement of the Best External Route in BGP", P.
   Marques, R. Fernando, E. Chen, P. Mohapatra, H. Gredler, draft-ietf-
   idr-best-external-05.txt, January 2012.

   [BGP-ERROR] "Revised Error Handling for BGP UPDATE Messages", J.
   Scudder, E. Chen, P. Mohapatra, K. Patel, draft-ietf-idr-error-
   handling-04.txt, June 2013.

   [RFC2119] "Key words for use in RFCs to Indicate Requirement
   Levels.", S. Bradner, March 1997.

Mohapatra, et al.                                              [Page 14]