Skip to main content

Additional Diffie-Hellman Tests for the Internet Key Exchange Protocol Version 2 (IKEv2)
draft-ietf-ipsecme-dh-checks-05

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 6989.
Authors Yaron Sheffer , Scott Fluhrer
Last updated 2015-10-14 (Latest revision 2013-06-04)
Replaces draft-sheffer-ipsecme-dh-checks
RFC stream Internet Engineering Task Force (IETF)
Intended RFC status Proposed Standard
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd Paul E. Hoffman
Shepherd write-up Show Last changed 2013-04-24
IESG IESG state Became RFC 6989 (Proposed Standard)
Action Holders
(None)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD Sean Turner
IESG note
Send notices to (None)
IANA IANA review state Version Changed - Review Needed
IANA action state RFC-Ed-Ack
draft-ietf-ipsecme-dh-checks-05
ipsecme                                                       Y. Sheffer
Internet-Draft                                                  Porticor
Updates: 5996 (if approved)                                   S. Fluhrer
Intended status: Standards Track                                   Cisco
Expires: December 6, 2013                                   June 4, 2013

               Additional Diffie-Hellman Tests for IKEv2
                    draft-ietf-ipsecme-dh-checks-05

Abstract

   This document adds a small number of mandatory tests required for the
   secure operation of IKEv2 with elliptic curve groups.  No change is
   required to IKE implementations that use modular exponential groups,
   other than a few rarely used so-called DSA groups.  This document
   updates the IKEv2 protocol, RFC 5996.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on December 6, 2013.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as

Sheffer & Fluhrer       Expires December 6, 2013                [Page 1]
Internet-Draft                  DH Tests                       June 2013

   described in the Simplified BSD License.

Table of Contents

   1.          Introduction . . . . . . . . . . . . . . . . . . . . .  3
   1.1.        Conventions used in this document  . . . . . . . . . .  3
   2.          Group Membership Tests . . . . . . . . . . . . . . . .  3
   2.1.        Sophie Germain Prime MODP Groups . . . . . . . . . . .  3
   2.2.        MODP Groups with Small Subgroups . . . . . . . . . . .  4
   2.3.        Elliptic Curve Groups  . . . . . . . . . . . . . . . .  4
   2.4.        Transition . . . . . . . . . . . . . . . . . . . . . .  5
   2.5.        Protocol Behavior  . . . . . . . . . . . . . . . . . .  5
   3.          Side-Channel Attacks . . . . . . . . . . . . . . . . .  6
   4.          Security Considerations  . . . . . . . . . . . . . . .  6
   4.1.        DH Key Reuse and Multiple Peers  . . . . . . . . . . .  7
   4.2.        DH Key Reuse: Variants . . . . . . . . . . . . . . . .  7
   4.3.        Groups not covered by this RFC . . . . . . . . . . . .  7
   4.4.        Behavior Upon Test Failure . . . . . . . . . . . . . .  8
   5.          IANA Considerations  . . . . . . . . . . . . . . . . .  8
   6.          Acknowledgements . . . . . . . . . . . . . . . . . . .  9
   7.          References . . . . . . . . . . . . . . . . . . . . . .  9
   7.1.        Normative References . . . . . . . . . . . . . . . . .  9
   7.2.        Informative References . . . . . . . . . . . . . . . .  9
   Appendix A. Appendix: Change Log . . . . . . . . . . . . . . . . . 10
   A.1.        -05  . . . . . . . . . . . . . . . . . . . . . . . . . 10
   A.2.        -04  . . . . . . . . . . . . . . . . . . . . . . . . . 10
   A.3.        -03  . . . . . . . . . . . . . . . . . . . . . . . . . 10
   A.4.        -02  . . . . . . . . . . . . . . . . . . . . . . . . . 10
   A.5.        -01  . . . . . . . . . . . . . . . . . . . . . . . . . 10
   A.6.        -00  . . . . . . . . . . . . . . . . . . . . . . . . . 11
               Authors' Addresses . . . . . . . . . . . . . . . . . . 11

Sheffer & Fluhrer       Expires December 6, 2013                [Page 2]
Internet-Draft                  DH Tests                       June 2013

1.  Introduction

   IKEv2 [RFC5996] consists of the establishment of a shared secret
   using the Diffie-Hellman (DH) protocol, followed by authentication of
   the two peers.  Existing implementations typically use modular
   exponential (MODP) DH groups, such as those defined in [RFC3526].

   IKEv2 does not require that any tests be performed by a peer
   receiving a public Diffie-Hellman key from the other peer.  This is
   fine for the common case of MODP groups.  For other DH groups, when
   peers reuse DH values across multiple IKE sessions, the lack of tests
   by the recipient results in a potential vulnerability (see
   Section 4.1 for more details).  In particular, this is true for
   Elliptic Curve (EC) groups whose use is becoming ever more popular.
   This document defines such tests for several types of DH groups.

   In addition, this document describes another potential attack related
   to reuse of DH keys: a timing attack.  This additional material is
   taken from [RFC2412].

   This document updates [RFC5996] by adding security requirements that
   apply to many of the protocol's implementations.

1.1.  Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2.  Group Membership Tests

   This section describes the tests that need to be performed by IKE
   peers receiving a Key Exchange (KE) payload.  The tests are
   RECOMMENDED for all implementations, but only REQUIRED for those that
   reuse DH private keys (as defined in [RFC5996], Sec. 2.12).  The
   tests apply to the recipient of a KE payload, and describe how it
   should check the received payload.  They are listed here according to
   the DH group being used.

2.1.  Sophie Germain Prime MODP Groups

   These are currently the most commonly used groups; all these groups
   have the property that (p-1)/2 is also prime; this section applies to
   any such MODP group.  Each recipient MUST verify that the peer's
   public value r is in the legal range (1 < r < p-1).  According to
   [Menezes], Sec 2.2, even with this check there remains the
   possibility of leaking a single bit of the secret exponent when DH

Sheffer & Fluhrer       Expires December 6, 2013                [Page 3]
Internet-Draft                  DH Tests                       June 2013

   keys are reused; this amount of leakage is insignificant.

   See Section 5 for the specific groups covered by this section.

2.2.  MODP Groups with Small Subgroups

   [RFC5114] defines modular exponential groups with small subgroups;
   these are modular exponential groups with comparatively small
   subgroups, and all have (p-1)/2 composite.  Sec. 2.1 of [Menezes]
   describes some informational leakage from a small subgroup attack on
   these groups, if the DH private value is reused.

   This leakage can be prevented if the recipient performs a test on the
   peer's public value, however this test is expensive (approximately as
   expensive as what reusing DH private values saves).  In addition, the
   NIST standard [NIST-800-56A] requires that test (see section
   5.6.2.4), hence anyone needing to conform to that standard will need
   to implement the test anyway.

   Because of the above, the IKE implementation MUST choose between one
   of the following two options:

   o  It MUST check both that the peer's public value is in range (1 < r
      < p-1) and that r^q = 1 mod p (where q is the size of the
      subgroup, as listed in the RFC).  DH private values MAY then be
      reused.  This option is appropriate if conformance to
      [NIST-800-56A] is required.
   o  It MUST NOT reuse DH private values (that is, the DH private value
      for each DH exchange MUST be generated from a fresh output of a
      cryptographically secure random number generator), and it MUST
      check that the peer's public value is in range (1 < r < p-1).
      This option is more appropriate if conformance to [NIST-800-56A]
      is not required.

   See Section 5 for the specific groups covered by this section.

2.3.  Elliptic Curve Groups

   IKEv2 can be used with elliptic curve groups defined over a field
   GF(p) [RFC5903] [RFC5114].  According to [Menezes], Sec. 2.3, there
   is some informational leakage possible.  A receiving peer MUST check
   that its peer's public value is valid; that is, the x and y
   parameters from the peer's public value satisfy the curve equation,
   y^2 = x^3 + ax + b mod p (where for groups 19, 20, 21, a=-3 (mod p),
   and all other values of a, b and p for the group are listed in the
   RFC).

   We note that an additional check to ensure that the public value is

Sheffer & Fluhrer       Expires December 6, 2013                [Page 4]
Internet-Draft                  DH Tests                       June 2013

   not the point at infinity is not needed, because IKE (in Sec. 7 of
   [RFC5903]) does not allow for encoding this value.

   See Section 5 for the specific groups covered by this section.

2.4.  Transition

   Existing implementations of IKEv2 with ECDH groups may be modified to
   include the tests described in the current document, even if they do
   not reuse DH keys.  The tests can be considered as sanity checks, and
   will prevent the code having to handle inputs that it may not have
   been designed to handle.

   ECDH implementations that do reuse DH keys MUST be enhanced to
   include the above tests.

2.5.  Protocol Behavior

   The recipient of a DH public key that fails one of the above tests
   must assume that the sender is either truly malicious or else it has
   a bug in its implementation.  The behavior defined below attempts to
   balance resistance to attackers that are trying to disrupt the IKE
   exchange, against the need to help a badly implemented peer by
   providing useful error indications.

   If this error happens during the IKE_SA_INIT exchange, then the
   recipient MUST drop the message that contains an invalid KE payload,
   and MUST NOT use that message when creating the IKE SA.

   If the implementation implements the DoS-resistant behavior proposed
   in Sec. 2.4 of [RFC5996], it may simply ignore the erroneous request
   or response message, and continue waiting for a later message
   containing a legitimate KE payload.

   If DoS-resistant behavior is not implemented, and the invalid KE
   payload was in the IKE_SA_INIT request, the implementation MAY send
   an INVALID_SYNTAX error notification back, and remove the in-progress
   IKE SA; if the invalid KE payload was in the IKE_SA_INIT response,
   then the implementation MAY simply delete the half created IKE SA,
   and re-initiate the exchange.

   If the invalid KE payload is received during the CREATE_CHILD_SA
   exchange (or any other exchange after the IKE SA has been
   established) and the invalid KE payload is in the request message,
   the Responder MUST reply with an INVALID_SYNTAX error notification
   and drop the IKE SA.  If the invalid KE payload is in a response, the
   Initiator getting this reply MUST immediately delete the IKE SA by
   sending an IKE SA Delete notification as a new exchange.  In this

Sheffer & Fluhrer       Expires December 6, 2013                [Page 5]
Internet-Draft                  DH Tests                       June 2013

   case the sender evidently has an implementation bug, and dropping the
   IKE SA makes it easier to detect.

3.  Side-Channel Attacks

   In addition to the small-subgroup attack, there is also a potential
   timing attack on IKE peers when they are reusing Diffie-Hellman
   secret values.  This is a side-channel attack, which means that it
   may or may not be a vulnerability in certain cases, depending on
   implementation details and the threat model.

   The remainder of this section is quoted from [RFC2412], Sec. 5, with
   a few minor clarifications.  This attack still applies to IKEv2
   implementations, and both to MODP groups and ECDH groups.  We also
   note that more efficient countermeasures are available for EC groups
   represented in projective form, but these are outside the scope of
   the current document.

   Timing attacks that are capable of recovering the exponent value used
   in Diffie-Hellman calculations have been described by Paul Kocher
   [Kocher].  In order to nullify the attack, implementors must take
   pains to obscure the sequence of operations involved in carrying out
   modular exponentiations.

   One potential method to foil these timing attacks is to use a
   "blinding factor".  In this method, a group element, r, is chosen at
   random, and its multiplicative inverse modulo p is computed, which
   we'll call r_inv. r_inv can be computed by the Extended Euclidean
   Method, using r and p as inputs.  When an exponent x is chosen, the
   value r_inv^x is also calculated.  Then, when calculating (g^y)^x,
   the implementation will calculate this sequence:

      A = r*g^y
      B = A^x = (r*g^y)^x = (r^x)(g^(xy))
      C = B*r_inv^x = (r^x)(r^(-1*x))(g^(xy)) = g^(xy)

   The blinding factor is only necessary if the exponent x is used more
   than 100 times (estimate by Richard Schroeppel).

4.  Security Considerations

   This entire document is concerned with the IKEv2 security protocol
   and the need to harden it in some cases.

Sheffer & Fluhrer       Expires December 6, 2013                [Page 6]
Internet-Draft                  DH Tests                       June 2013

4.1.  DH Key Reuse and Multiple Peers

   This section describes one variant of the attack prevented by the
   tests defined above.

   Suppose that IKE peer Alice maintains IKE security associations with
   peers Bob and Eve. Alice uses the same secret ECDH key for both SAs,
   which is allowed with some restrictions.  If Alice does not implement
   these tests, Eve will be able to send a malformed public key, which
   would allow her to efficiently determine Alice's private key (as
   described in Sec. 2 of [Menezes]).  Since the key is shared, Eve will
   be able to obtain Alice's shared IKE SA key with Bob.

4.2.  DH Key Reuse: Variants

   Private DH keys can be reused in different ways, with subtly
   different security implications.  For example:

   1.  DH keys are reused for multiple connections (IKE SAs) to the same
       peer, and for connections to different peers.
   2.  DH keys are reused for multiple connections to the same peer
       (e.g. when the peer is identified by its IP address) but not for
       different peers.
   3.  DH keys are reused only when they had not been used to complete
       an exchange, e.g. when the peer replies with an
       INVALID_KE_PAYLOAD notification.

   Both the small subgroup attack and the timing attack described in
   this document apply at least to options #1 and #2.

4.3.  Groups not covered by this RFC

   There are a number of group types that are not specifically addressed
   by this RFC.  A document that defines such a group MUST describe the
   tests required by that group.

   One specific type of group would be an even-characteristic elliptic
   curve group.  Now, these curves have cofactors greater than 1; this
   leads to a possibility of some information leakage.  There are
   several ways to address this information leakage, such as performing
   a test analogous to the test in section 2.2, or adjusting the ECDH
   operation to avoid this leakage (such as "ECC CDH", where the shared
   secret really is hxyG).  Because the appropriate test depends on how
   the group is defined, we cannot document it in advance.

Sheffer & Fluhrer       Expires December 6, 2013                [Page 7]
Internet-Draft                  DH Tests                       June 2013

4.4.  Behavior Upon Test Failure

   The behavior recommended in Section 2.5 is in line with generic error
   treatment during the IKE_SA_INIT exchange, Sec. 2.21.1 of [RFC5996].
   The sender is not required to send back an error notification, and
   the recipient cannot depend on this notification because it is
   unauthenticated, and may in fact have been sent by an attacker trying
   to DoS the connection.  Thus, the notification is only useful to
   debug implementation errors.

   On the other hand, the error notification is secure in the sense that
   no secret information is leaked.  All IKEv2 Diffie-Hellman groups are
   publicly known, and none of the tests defined here depend on any
   private key.  In fact the tests can all be performed by an
   eavesdropper.

   The situation when the failure occurs in the Create Child SA exchange
   is different, since everything is protected by an IKE SA.  The peers
   are authenticated, and error notifications can be relied on.  See
   Sec. 2.21.3 of [RFC5996] for more details on error handling in this
   case.

5.  IANA Considerations

   This document requests that IANA should add a column named "Recipient
   Tests" to the IKEv2 DH Group Transform IDs Registry
   [IANA-DH-Registry].

   This column should initially be populated as per the following table.

       +------------------------------------+---------------------+
       |               Number               |   Recipient Tests   |
       +------------------------------------+---------------------+
       |     1, 2, 5, 14, 15, 16, 17, 18    | [current], Sec. 2.1 |
       |             22, 23, 24             | [current], Sec. 2.2 |
       | 19, 20, 21, 25, 26, 27, 28, 29, 30 | [current], Sec. 2.3 |
       +------------------------------------+---------------------+

   Note to RFC Editor: please replace [current] by the RFC number
   assigned to this document.

   Groups 27-30 have been recently defined in
   [I-D.merkle-ikev2-ke-brainpool].

   Future documents that define new DH groups for IKEv2 are REQUIRED to
   provide this information for each new group, possibly by referring to
   the current document.

Sheffer & Fluhrer       Expires December 6, 2013                [Page 8]
Internet-Draft                  DH Tests                       June 2013

6.  Acknowledgements

   We would like to thank Dan Harkins who initially raised this issue on
   the ipsec mailing list.  Thanks to Tero Kivinen and Rene Struik for
   their useful comments.  Much of the text in Section 3 is taken from
   [RFC2412] and we would like to thank its author, Hilarie Orman.

   The document was prepared using the lyx2rfc tool, created by Nico
   Williams.

7.  References

7.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC5996]  Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen,
              "Internet Key Exchange Protocol Version 2 (IKEv2)",
              RFC 5996, September 2010.

7.2.  Informative References

   [RFC2412]  Orman, H., "The OAKLEY Key Determination Protocol",
              RFC 2412, November 1998.

   [RFC3526]  Kivinen, T. and M. Kojo, "More Modular Exponential (MODP)
              Diffie-Hellman groups for Internet Key Exchange (IKE)",
              RFC 3526, May 2003.

   [RFC5114]  Lepinski, M. and S. Kent, "Additional Diffie-Hellman
              Groups for Use with IETF Standards", RFC 5114,
              January 2008.

   [RFC5903]  Fu, D. and J. Solinas, "Elliptic Curve Groups modulo a
              Prime (ECP Groups) for IKE and IKEv2", RFC 5903,
              June 2010.

   [I-D.merkle-ikev2-ke-brainpool]
              Merkle, J. and M. Lochter, "Using the ECC Brainpool Curves
              for IKEv2 Key Exchange",
              draft-merkle-ikev2-ke-brainpool-06 (work in progress),
              April 2013.

   [NIST-800-56A]
              National Institute of Standards and Technology (NIST),
              "Recommendation for Pair-Wise Key Establishment Schemes

Sheffer & Fluhrer       Expires December 6, 2013                [Page 9]
Internet-Draft                  DH Tests                       June 2013

              Using Discrete Logarithm Cryptography (Revised)", NIST PUB
              800-56A, March 2007.

   [Kocher]   Kocher, P., "Timing Attacks on Implementations of Diffie-
              Hellman, RSA, DSS, and Other Systems", December 1996,
              <http://www.cryptography.com/timingattack/paper.html>.

   [Menezes]  Menezes, A. and B. Ustaoglu, "On Reusing Ephemeral Keys In
              Diffie-Hellman Key Agreement Protocols", December 2008, <h
              ttp://www.cacr.math.uwaterloo.ca/techreports/2008/
              cacr2008-24.pdf>.

   [IANA-DH-Registry]
              IANA, "Internet Key Exchange Version 2 (IKEv2) Parameters,
              Transform Type 4 - Diffie-Hellman Group Transform IDs",
              Jan. 2005, <http://www.iana.org/assignments/
              ikev2-parameters/ikev2-parameters.xml#ikev2-parameters-8>.

Appendix A.  Appendix: Change Log

   Note to RFC Editor: please remove this section before publication.

A.1.  -05

   o  Resolved IESG members' comments.

A.2.  -04

   o  Implemented Sean's AD review, and removed the inapplicable
      requirement on the point at infinity.

A.3.  -03

   o  Added the Brainpool curves to the IANA registration table.

A.4.  -02

   o  Based on Tero's review: Improved the protocol behavior, and
      mentioned that these checks apply to Create Child SA.  Added a
      discussion of DH timing attacks, stolen from RFC 2412.

A.5.  -01

   o  Corrected an author's name that was misspelled.
   o  Added recipient behavior if a test fails, and the related security
      considerations.

Sheffer & Fluhrer       Expires December 6, 2013               [Page 10]
Internet-Draft                  DH Tests                       June 2013

A.6.  -00

   o  First WG document.
   o  Clarified IANA actions.
   o  Discussion of potential future groups not covered here.
   o  Clarification re: practicality of recipient tests for DSA groups.

Authors' Addresses

   Yaron Sheffer
   Porticor
   10 Yirmiyahu St.
   Ramat HaSharon  47298
   Israel

   Email: yaronf.ietf@gmail.com

   Scott Fluhrer
   Cisco Systems
   1414 Massachusetts Ave.
   Boxborough, MA  01719
   USA

   Email: sfluhrer@cisco.com

Sheffer & Fluhrer       Expires December 6, 2013               [Page 11]