Remote attestation over EDHOC
draft-ietf-lake-ra-00
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Active".
|
|
|---|---|---|---|
| Author | SONG Yuxuan | ||
| Last updated | 2025-02-11 | ||
| Replaces | draft-song-lake-ra | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Document | |
| Associated WG milestone |
|
||
| On agenda | lake at IETF-126 | ||
| Document shepherd | (None) | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-lake-ra-00
Lightweight Authenticated Key Exchange Y. Song
Internet-Draft Inria
Intended status: Standards Track 11 February 2025
Expires: 15 August 2025
Remote attestation over EDHOC
draft-ietf-lake-ra-00
Abstract
This document specifies how to perform remote attestation as part of
the lightweight authenticated Diffie-Hellman key exchange protocol
EDHOC (Ephemeral Diffie-Hellman Over COSE), based on the Remote
ATtestation procedureS (RATS) architecture.
About This Document
This note is to be removed before publishing as an RFC.
The latest revision of this draft can be found at https://lake-
wg.github.io/ra/draft-ietf-lake-ra.html. Status information for this
document may be found at https://datatracker.ietf.org/doc/draft-ietf-
lake-ra/.
Discussion of this document takes place on the Lightweight
Authenticated Key Exchange Working Group mailing list
(mailto:lake@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/browse/lake/. Subscribe at
https://www.ietf.org/mailman/listinfo/lake/.
Source for this draft and an issue tracker can be found at
https://github.com/lake-wg/ra.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
Song Expires 15 August 2025 [Page 1]
Internet-Draft RA-EDHOC February 2025
This Internet-Draft will expire on 15 August 2025.
Copyright Notice
Copyright (c) 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions and Definitions . . . . . . . . . . . . . . . . . 4
3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. Remote Attestation in EDHOC . . . . . . . . . . . . . . . . . 6
5.1. Target . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.1.1. IoT Device Attestation (IoT) . . . . . . . . . . . . 6
5.1.2. Network Service Attestation (Net) . . . . . . . . . . 6
5.2. Model . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.2.1. Background-check Model (BG) . . . . . . . . . . . . . 6
5.2.2. Passport Model (PP) . . . . . . . . . . . . . . . . . 9
5.3. EDHOC Message Flow . . . . . . . . . . . . . . . . . . . 12
5.3.1. EDHOC Forward Message Flow (Fwd) . . . . . . . . . . 12
5.3.2. EDHOC Reverse Message Flow (Rev) . . . . . . . . . . 12
6. Instantiation of Remote Attestation Protocol . . . . . . . . 12
6.1. (IoT, BG, Fwd): IoT Device Attestation . . . . . . . . . 12
6.2. (Net, PP, Fwd): Network Service Attestation . . . . . . . 14
7. Mutual Attestation in EDHOC . . . . . . . . . . . . . . . . . 15
7.1. (IoT, BG, Fwd) - (Net, PP, Fwd) . . . . . . . . . . . . . 16
8. Error Handling . . . . . . . . . . . . . . . . . . . . . . . 18
8.1. EDHOC Error "Attestation failed" . . . . . . . . . . . . 18
9. Security Considerations . . . . . . . . . . . . . . . . . . . 18
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
10.1. EDHOC External Authorization Data Registry . . . . . . . 19
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 20
11.1. Normative References . . . . . . . . . . . . . . . . . . 20
11.2. Informative References . . . . . . . . . . . . . . . . . 20
Appendix A. Example: Remote Attestation Flow . . . . . . . . . . 21
Appendix B. Remote attestation in parallel with enrollment
authorization . . . . . . . . . . . . . . . . . . . . . . 23
Song Expires 15 August 2025 [Page 2]
Internet-Draft RA-EDHOC February 2025
Appendix C. Example: Firmware Version . . . . . . . . . . . . . 23
Appendix D. Open discussion: remote attestation over EDHOC/ over
OSCORE . . . . . . . . . . . . . . . . . . . . . . . . . 25
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 25
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 25
1. Introduction
Remote attestation is a security process which verifies and confirms
the integrity and trustworthiness of a remote device or system in the
network. This process helps establish a level of trust in the remote
system before allowing the device to e.g. join the network or get
access to some sensitive information and resources. The use cases
that require remote attestation include secure boot and firmware
management, cloud computing, network access control, etc.
The IETF working group Remote ATtestation procedureS (RATS) has
defined an architecture [RFC9334] for remote attestation. The three
main roles in the RATS architecture are the Attester, the Verifier
and the Relying Party. The Attester generates the evidence
concerning its identity and integrity, which must be appraised by the
Verifier for its validity. Then, the Verifier produces the
attestation result, which is consequently used by the Relying Party
for the purposes of reliably applying application-specific actions.
One type of interaction model defined in the RATS architecture is
called the background-check model. It resembles the procedure of how
employers perform background checks to determine the prospective
employee's trustworthiness, by contacting the respective organization
that issues a report. In this case, the employer acts as the Relying
Party, the employee acts as the Attester and the organization acts as
the Verifier. The Attester conveys evidence directly to the Relying
Party and the Relying Party forwards the evidence to the Verifier for
appraisal. Once the attestation result is computed by the Verifier,
it is sent back to the Relying Party to decide what action to take
based on the attestation result. Another model is called passport
model, where the Attester communicates directly with the Verifier.
The Attester presents the evidence to the Verifier and gets an
attestation result from the Verifier. Then the Attester conveys the
attestation result to the Relying Party. This specification employs
both the RATS background-check model and the passport model.
Song Expires 15 August 2025 [Page 3]
Internet-Draft RA-EDHOC February 2025
This document specifies the protocol between the Attester and the
Relying Party. The details of the protocol between the Relying Party
and the Verifier in the background-check model, and the protocol
between the Attester and the Verifier in the passport model are out
of the scope. This communication may be secured through protocols
such as EDHOC, TLS or other security protocols that support the
secure transmission to and from the Verifier.
One way of conveying attestation evidence or the attestation result
is the Entity Attestation Token (EAT) [I-D.ietf-rats-eat]. It
provides an attested claims set which can be used to determine a
level of trustworthiness. This specification relies on the EAT as
the format for attestation evidence and the attestation result.
Ephemeral Diffie-Hellman over COSE (EDHOC) [RFC9528] is a lightweight
authenticated key exchange protocol for highly constrained networks.
In EDHOC, the two parties involved in the key exchange are referred
to as the Initiator (I) and the Responder (R). EDHOC supports the
transport of external authorization data, through the dedicated EAD
fields. This specification delivers EAT through EDHOC.
Specifically, EAT is transported as an EAD item. This specification
also defines new EAD items needed to perform remote attesation over
EDHOC in Section 5.2.1.1 and Section 5.2.2.1.
For the generation of evidence, the Attester incorporates an internal
attestation service, including a specific trusted element known as
the "root of trust". Root of trust serves as the starting point for
establishing and validating the trustworthiness appraisals of other
components on the system. The measurements signed by the attestation
service are referred to as the Evidence. The signing is requested
through an attestation API. How the components are separated between
the secure and non-secure worlds on a device is out of scope of this
specification.
2. Conventions and Definitions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
The reader is assumed to be familiar with the terms and concepts
defined in EDHOC [RFC9528] and RATS architecture [RFC9334].
Song Expires 15 August 2025 [Page 4]
Internet-Draft RA-EDHOC February 2025
3. Overview
This specification describes how to perform remote attestation over
the EDHOC protocol, following the RATS architecture. EDHOC provides
the benefit of minimal message overhead and reduced round trips for a
lightweight authentication. More importantly, by integrating remote
attestation with EDHOC, attestation can be run in parallel with
authentication, improving the efficiency and maintaining lightweight
properties.
Remote attestation protocol elements are carried within EDHOC's
External Authorization Data (EAD) fields. EDHOC [RFC9528] supports
one or more EAD items in each EAD field.
In Section 5, this document defines three independent dimensions for
performing remote attestation over EDHOC:
1. Target (see Section 5.1) defining the entity that undergoes the
attestation process (IoT device or network service).
2. Model (see Section 5.2) defining the attestation model in use
based on the RATS architecture (background-check model or
passport model).
3. Message Flow (see Section 5.3) defining the EDHOC message flow in
use (forward message flow or reverse message flow).
This document specifies the cases that are suited for constrained IoT
environments.
EDITOR NOTE: add an overview figure
4. Assumptions
In background-check model, one assumption is that the Verifier
outputs a fresh nonce and that same nonce is passed on to the EDHOC
session. The Verifier is assumed to know how to verify multiple
formats of the evidence type. This specification assumes that the
Relying Party also has knowledge about the Attester, so it can narrow
down the evidence type selection and send to the Attester only one
format of the evidence type. The Attester should have an explicit
relation with the Verifier, such as from device manufacturing, so
that the Verifier can evaluate the Evidence that is produced by the
Attester.
Song Expires 15 August 2025 [Page 5]
Internet-Draft RA-EDHOC February 2025
In the passport model, the credential identity of the Verifier is
assumed to be stored at the Attester and the Relying Party, which
means the Verifier is trusted by the Attester and the Relying Party
to obtain the attestation result.
EDITOR NOTE: add attestation public key stored in Verifier
5. Remote Attestation in EDHOC
This section specifies three independent dimensions that characterize
the remote attestation process over EDHOC.
5.1. Target
Defines the entity that undergoes the attestation process.
5.1.1. IoT Device Attestation (IoT)
The IoT device acts as the Attester.
5.1.2. Network Service Attestation (Net)
The network service acts as the Attester.
Unlike IoT devices, network services typically have more
computational power and capabilities, enabling them to handle complex
attestation processes when more demanding tasks are required of the
Attester.
5.2. Model
Defines the attestation models based on RATS architecture. This
specification supports both the RATS background-check model (see
Section 5.2.1) and the passport model (see Section 5.2.2). The
corresponding EAD items for background-check model and the passport
model are independent of each other. The EAD items are specified in
Section 5.2.1.1 for the background-check model and in Section 5.2.2.1
for the passport model.
5.2.1. Background-check Model (BG)
In the background-check model, the Attester sends the evidence to the
Relying Party. The Relying Party transfers the evidence to the
Verifier and gets back the attestation result from the Verifier.
Song Expires 15 August 2025 [Page 6]
Internet-Draft RA-EDHOC February 2025
An EDHOC session is established between the Attester and the Relying
Party. A negotiation of the evidence type is required before the
Attester sends the evidence. All three parties must agree on a
selected evidence type.
The Attester first sends a list of the proposed evidence types to the
Relying Party. The list is formatted as an Attestation proposal in
an EDHOC EAD item. The Relying Party relays the list to the Verifier
and receives at least one supported evidence type from the Verifier
in return. If the Relying Party receives more than one evidence
type, a single evidence type should be selected by the Relying Party
based on its knowledge of the Attester. The Relying Party then sends
it back within the Attestation request to the Attester.
A nonce, at least 8-bytes long [I-D.ietf-rats-eat]), guarantees the
freshness of the attestation session. The nonce is generated by the
Verifier and sent to the Relying Party. The Relying Party puts the
nonce and the selected evidence type together in a tuple to generate
an Attestation request.
Once the Attester receives the Attestation request, it can call its
attestation service to generate the evidence, with the nonce value as
one of the inputs.
5.2.1.1. External Authorization Data (EAD) Items for background-check
model
EAD items that are used for the background-check model are defined in
this section.
5.2.1.1.1. Attestation_proposal
To propose a list of provided evidence types in background-check
model, the Attester transports the Proposed_EvidenceType object. It
signals to the Relying Party the proposal to do remote attestation,
as well as which types of the attestation claims the Attester
supports. The Proposed_EvidenceType is encoded in CBOR in the form
of a sequence.
The EAD item for an attestation proposal is:
* ead_label = TBD1
* ead_value = Attestation_proposal, which is a CBOR byte string:
Song Expires 15 August 2025 [Page 7]
Internet-Draft RA-EDHOC February 2025
Attestation_proposal = bstr .cbor Proposed_EvidenceType
Proposed_EvidenceType = [ + content-format ]
content-format = uint
where
* Proposed_EvidenceType is an array that contains all the supported
evidence types by the Attester.
* There MUST be at least one item in the array.
* content-format is an indicator of the format type (e.g.,
application/eat+cwt with an appropriate eat_profile parameter
set), from [IANA-CoAP-Content-Formats].
The sign of ead_label TBD1 MUST be negative to indicate that the EAD
item is critical. If the receiver cannot recognize the critical EAD
item, or cannot process the information in the critical EAD item,
then the receiver MUST send an EDHOC error message back as defined in
Section 6 of [RFC9528].
5.2.1.1.2. Attestation_request
As a response to the attestation proposal, the Relying Party signals
to the Attester the supported and requested evidence type. In case
none of the evidence types is supported, the Relying Party rejects
the first message_1 with an error indicating support for another
evidence type.
The EAD item for an attestation request is:
* ead_label = TBD1
* ead_value = Attestation_request, which is a CBOR byte string:
Attestation_request = bstr .cbor Selected_EvidenceType
Selected_EvidenceType = (
content-format: uint,
nonce: bstr .size 8..64
)
where
* content-format is the selected evidence type by the Relying Party
and supported by the Verifier.
Song Expires 15 August 2025 [Page 8]
Internet-Draft RA-EDHOC February 2025
* nonce is generated by the Verifier and forwarded by the Relying
Party.
The sign of ead_label TBD2 MUST be negative to indicate that the EAD
item is critical. If the receiver cannot recognize the critical EAD
item, or cannot process the information in the critical EAD item,
then the receiver MUST send an EDHOC error message back as defined in
Section 6 of [RFC9528].
5.2.1.1.3. Evidence
As a response to the attestation request, the Attester calls its
local attestation service to generate and return the serialized EAT
[I-D.ietf-rats-eat] as Evidence.
The EAD item is:
* ead_label = TBD1
* ead_value is a serialized EAT.
EAT is specified in [I-D.ietf-rats-eat].
5.2.1.1.4. trigger_bg
The EAD item trigger_bg is used when the sender triggers the receiver
to start a remote attestation in the background-check model. The
receiver MUST reply with an EAD item corresponding to the background-
check model. The ead_value can be empty, as the ead_label serves as
the trigger.
The EAD item is:
* ead_label = TBD2
* ead_value = null
5.2.2. Passport Model (PP)
In the passport model, the Attester sends the evidence to the
Verifier. After the Attester receives the attestation result from
the Verifier, the Attester sends the attestation result to the
Relying Party.
An EDHOC session is established between the Attester and the Relying
Party. The Attester and the Relying Party should decide from which
Verifier the Attester obtains the attestation result and transfers it
to the Relying Party. The Attester first sends a list of the
Song Expires 15 August 2025 [Page 9]
Internet-Draft RA-EDHOC February 2025
Verifier identities that it can get the attestation result. The
Relying Party selects one trusted Verifier identity and sends it back
as a Result request.
Regarding the freshness in passport model, the Attester could either
establish a real-time connection with the selected Verifier, or use a
pre-stored attestation result from the selected Verifier. If the
attestation result is not obtained via a real-time connection, it
should include a time stamp and/or expiry time to indicate its
validity. Time synchronization is out of scope of this
specification.
Once the Attester obtains the attestation result from the selected
Verifier, it sends the attestation result to the Relying Party.
5.2.2.1. External Authorization Data (EAD) Items for passport model
EAD items that are used for the passport model are defined in this
section.
5.2.2.1.1. Result_proposal
An attestation result proposal contains the identification of the
credentials of the Verifiers to indicate Verifiers' indentities. The
identification of credentials relies on COSE header parameters
[IANA-COSE-Header-Parameters], with a header label and credential
value.
The EAD item for the attestation result proposal is:
* ead_label = TBD3
* ead_value = Result_proposal, which is a CBOR byte string:
Result_proposal = bstr .cbor Proposed_VerifierIdentity
Proposed_VerifierIdentity = [ + VerifierIdentity ]
VerifierIdentity = {
label => values
}
where
* Proposed_VerifierIdentity is defined as a list of one or more
VerifierIdentity elements.
* Each VerifierIdentity within the list is a map defined in
[IANA-COSE-Header-Parameters] that:
Song Expires 15 August 2025 [Page 10]
Internet-Draft RA-EDHOC February 2025
- label = int / tstr
- values = any
5.2.2.1.2. Result_request
As a response to the attestation result proposal, the Relying Party
signals to the Attester the trusted Verifier. In case none of the
Verifiers can be trusted by the Relying Party, the session is
aborted. Relying Party generates a nonce to ensure the freshness of
the attestation result from the Verifier.
The EAD item for an attestation result request is:
* ead_label = TBD3
* ead_value = Result_request, which is a CBOR byte string:
Result_request = bstr .cbor Request_structure
Request_structure = {
selected_verifier: VerfierIdentity
}
5.2.2.1.3. Result
The attestation result is generated and signed by the Verifier as a
serialized EAT [I-D.ietf-rats-eat]. The Relying Party can decide
what action to take with regards to the Attester based on the
information elements in attetation result.
The EAD item is:
* ead_label = TBD3
* ead_value is a serialized EAT.
5.2.2.1.4. trigger_pp
The EAD item trigger_pp is used when the sender triggers the receiver
to start a remote attestation in the passport model. The receiver
MUST reply with an EAD item correspondign to the passport model. The
ead_value can be empty, as the ead_label serves as the trigger.
The EAD item is:
* ead_label = TBD4
Song Expires 15 August 2025 [Page 11]
Internet-Draft RA-EDHOC February 2025
* ead_value = null
5.3. EDHOC Message Flow
The EDHOC protocol defines two possible message flows, namely the
EDHOC forward message flow and the EDHOC reverse message flow (see
Appendix A.2.2 of [RFC9528]). In this specification, both flows can
be used to perform remote attestation.
5.3.1. EDHOC Forward Message Flow (Fwd)
In forward message flow, EDHOC may run with the Initiator as a CoAP/
HTTP client. Remote attestation over EDHOC starts with a POST
requests to the Uri-Path: "/.well-known/lake-ra".
5.3.2. EDHOC Reverse Message Flow (Rev)
In the reverse message flow, the CoAP/HTTP client is the Responder
and the server is the Initiator. A new EDHOC session begins with an
empty POST request to the server's resource for EDHOC.
6. Instantiation of Remote Attestation Protocol
We use the format (Target, Model, Message Flow) to denote
instantiations. For example, (IoT, BG, Fwd) represents IoT device
attestation using the background-check model with forward EDHOC
message flow.
Although there are 8 cases (IoT/Net, BG/PP, Fwd/Rev), this document
specifies the most relevant instantiations for constrained IoT
environments.
6.1. (IoT, BG, Fwd): IoT Device Attestation
A common use case for (IoT, BG, Fwd) is to attest an IoT device to a
network server. For example, doing remote attestation to verify that
the latest version of firmware is running on the IoT device before
the network server allows it to join the network (see Appendix C).
An overview of doing IoT device attestation in background-check model
and EDHOC forward message flow is established in Figure 1. EDHOC
Initiator plays the role of the RATS Attester (A). EDHOC Responder
plays the role of the RATS Relying Party (RP). The Attester and the
Relying Party communicate by transporting messages within EDHOC's
External Authorization Data (EAD) fields. An external entity, out of
scope of this specification, plays the role of the RATS Verifier (V).
The EAD items specific to the background-check model are defined in
Section 5.2.1.1.
Song Expires 15 August 2025 [Page 12]
Internet-Draft RA-EDHOC February 2025
The Attester starts the attestation by sending an Attestation
proposal in EDHOC message_1. The Relying Party generates EAD_2 with
the received evidence type and nonce from the Verifier, and sends it
to the Attester. The Attester sends the Evidence to the Relying
Party in EAD_3. The Verifier evaluates the Evidence and sends the
Attestation result to the Relying Party.
+-----------------+ +-----------------+
| IoT device | | Network service |
+-----------------+ +-----------------+
| EDHOC Initiator | | EDHOC Responder |
+-----------------+ +-----------------+ +----------+
| Attester | | Relying Party | | Verifier |
+--------+--------+ +--------+--------+ +-----+----+
| | |
| EAD_1 = Attestation proposal | |
+------------------------------->| |
| | |
| | Attestation proposal, C_R |
| +-------------------------->|
| |<--------------------------+
| | EvidenceType(s), Nonce |
| | |
| EAD_2 = Attestation request | |
|<-------------------------------+ |
| | |
| EAD_3 = Evidence | |
+------------------------------->| |
| | Evidence, C_R |
| +-------------------------->|
| |<--------------------------+
| | Attestation result |
| | |
| | |
| | |
| <----------------------------> | |
| EDHOC session | |
Figure 1: Overview of IoT device attestation in background-check
model and EDHOC forward message flow. EDHOC is used between A
and RP.
Song Expires 15 August 2025 [Page 13]
Internet-Draft RA-EDHOC February 2025
6.2. (Net, PP, Fwd): Network Service Attestation
One use case for (Net, PP, Fwd) is when a network server needs to
attest itself to a client (e.g., an IoT device). For example, the
client needs to send some sensitive data to the network server, which
requires the network server to be attested first. In (Net, PP, Fwd),
the network server acts as an Attester and the client acts as a
Relying Party.
An overview of the message flow is illustrated in Figure 2. EDHOC
Initiator plays the role of the RATS Relying Party. EDHOC Responder
plays the role of the RATS Attester. An external entity, out of
scope of this specification, plays the role of the RATS Verifier.
The EAD items specific to the passport model are defined in
Section 5.2.2.1.
The Relying Party asks the Attester to do a remote attestation by
sending a trigger_pp (see Section 5.2.2.1.4) in EDHOC message_1. The
Attester replies to the Relying Party with a Result proposal in
EAD_2. Then the Relying Party selects a trusted Verifier identity
and sends it as a Result request. How the Attester negotiates with
the selected Verifier to get the attestation result is out of scope
of this specification. A fourth EDHOC message is required to send
the Result from the Attester to the Relying Party.
Song Expires 15 August 2025 [Page 14]
Internet-Draft RA-EDHOC February 2025
+-----------------+ +-----------------+
| IoT device | | Network service |
+-----------------+ +-----------------+
| EDHOC Initiator | | EDHOC Responder |
+-----------------+ +-----------------+ +----------+
| Relying Party | | Attester | | Verifier |
+--------+--------+ +--------+--------+ +-----+----+
| | |
| EAD_1 = trigger_PP | |
+--------------------------->| |
| | |
| EAD_2 = Result proposal | |
|<---------------------------+ |
| | |
| EAD_3 = Result request | |
+--------------------------->| (request) |
| +--- --- --- --- --- -->|
| |<--- --- --- --- --- --+
| | Result |
| EAD_4 = Result | |
|<---------------------------+ |
| | |
| | |
| | |
| <------------------------> | |
| EDHOC session | |
Figure 2: Overview of network service attestation in passport
model and EDHOC forward message flow. EDHOC is used between RP
and A. The dashed line illustrates a logical connection that
does not need to occur in real time.
7. Mutual Attestation in EDHOC
Mutual attestation over EDHOC combines the cases where one of the
EDHOC parties uses the IoT device attestation and the other uses the
Network service attestation. Performing mutual attestation to a
single EDHOC message flow acheives a lightweight use with reduced
message overhead. Note that the message flow for the two parties in
mutual attestation needs to be the same.
In this specification, we list the most relevant mutual attestation
example for constrained IoT environments.
Song Expires 15 August 2025 [Page 15]
Internet-Draft RA-EDHOC February 2025
7.1. (IoT, BG, Fwd) - (Net, PP, Fwd)
In this example, the mutual attestation is performed in EDHOC forward
message flow, by one IoT device attestation in background-check model
and another network service attestation in passport model. The
process is illustrated in Figure 3. How the Network service connects
with the Verifier_1 and potential Verifier_2 is out of scope in this
specification.
The first remote attestation is initiated by the IoT device (A_1) in
background-check model. In parallel, the IoT device (A_1) requests
the network service (A_2) to perform a remote attestation in passport
model. EAD_2 carries the EAD items Attestation request and Result
proposal. EAD_3 carries the EAD items Evidence and Result request.
EAD_4 carries the EAD item Result for the passport model.
Song Expires 15 August 2025 [Page 16]
Internet-Draft RA-EDHOC February 2025
+-----------------+ +-----------------+
| IoT device | | Network service |
+-----------------+ +-----------------+
| EDHOC Initiator | | EDHOC Responder |
+-----------------+ +-----------------+ +------------+ +------------+
| A_1/RP_2 | | RP_1/A_2 | | Verifier_1 | | Verifier_2 |
+--------+--------+ +--------+--------+ +------+-----+ +------+-----+
| | | |
| EAD_1 = Attestation proposal, | | |
| trigger_PP | | |
+-------------------------------->| | |
| | | |
| | | |
| | Attestation proposal, C_R | |
| +--------------------------->| |
| |<---------------------------+ |
| | EvidenceType(s), Nonce | |
| EAD_2 = Attestation request, | | |
| Result proposal | | |
|<--------------------------------+ | |
| | | |
| | | |
| EAD_3 = Evidence, | | |
| Result request | | |
+-------------------------------->| | |
| | | |
| | Evidence, C_R | |
| +--------------------------->| (Request) |
| +--- --- --- --- --- --- ---+ --- --- --- --- --- --->|
| | | |
| | | |
| | Attestation result | |
| |<---------------------------+ |
| | | |
| |<--- --- --- --- --- --+ --- --- --- --- --- ---+
| | Result | |
| EAD_4 = Result | | |
|<--------------------------------+ | |
| | | |
| | | |
| | | |
| | | |
| <-----------------------------> | | |
| EDHOC session | | |
Song Expires 15 August 2025 [Page 17]
Internet-Draft RA-EDHOC February 2025
Figure 3: Overview of mutual attestation of (IoT, BG, Fwd) -
(Net, PP, Fwd). EDHOC is used between A and RP. The dashed line
illustrates a logical connection that does not need to occur in
real time.
8. Error Handling
This section specifies a new EDHOC error code and how it is used in
the proposed protocol.
8.1. EDHOC Error "Attestation failed"
This section specifies a new EDHOC error "Attestation failed". The
format of the error message follows the one in EDHOC protocol(see
Section 6 of [RFC9528]).
+----------+----------------+----------------------------------------+
| ERR_CODE | ERR_INFO Type | Description |
+==========+================+========================================+
| TBD5 | attestation | Attestation failed |
+----------+----------------+----------------------------------------+
Figure 4: EDHOC error code and error information for Attestation
failed.
Error code TBD5 indicates to the receiver that the remote attestation
is failed after the evidence is sent. This can occur in two cases:
1. The Verifier evaluates the attestation evidence and returns a
negative result based on the Verifier's appraisal policy.
2. The Verifier provides a positive attestation result to the
Relying Party, but the Relying Party can not establish a
sufficient level of trust to proceed decision-specific actions
based on its appraisal policy.
In case 1, the Verifier signals the error to the Relying Party, which
then generates an EDHOC "Attestation failed" error and send it to the
Attester. In case 2, the Relying Party directly generates and sends
the "Attestation failed" error to the Attester. The application
decides how to handle the error message.
9. Security Considerations
This specification is performed over EDHOC [RFC9528] by using EDHOC's
EAD fields. The privacy considerations of EADs in EDHOC apply to
this specification.
Song Expires 15 August 2025 [Page 18]
Internet-Draft RA-EDHOC February 2025
EAD_1 is not resistant to either active attackers or passive
attackers, because neither the Initiator nor the Responder has been
authenticated.
Although EAD_2 is encrypted, the Initiator has not been
authenticated, rendering EAD_2 vulnerable against the active
attackers.
The ead items in EAD_1 and EAD_2 MAY be very specific and potentially
reveal sensitive information about the device. The leaking of the
data in EAD_1 and/or EAD_2 MAY risk to be used by the attackers for
malicious purposes. Data in EAD_3 and EAD_4 are protected between
the Initiator and the Responder in EDHOC.
Mutual attestation carries a lower risk for EAD items when the
Responder is the Attester. For the mutual attestation at the EDHOC
Responder, only the Attestation_proposal/Result_proposal in EAD_2 is
not protected to active attackers. Both the Attestation_request/
Result_request in EAD_3 and the Evidence/Result in EAD_4 are
protected.
10. IANA Considerations
10.1. EDHOC External Authorization Data Registry
IANA is requested to register the following entry in the "EDHOC
External Authorization Data" registry under the group name "Ephemeral
Diffie-Hellman Over Cose (EDHOC)".
* The ead_label = TBD1 corresponds to the ead_value
Attestation_proposal in Section 5.2.1.1.1, Attestation_request in
Section 5.2.1.1.2 and Evidence in Section 5.2.1.1.3.
* The ead_label = TBD2 corresponds to the EAT item trigger_bg as
specified in Section 5.2.1.1.4.
* The ead_label = TBD3 corresponds to the ead_value Result_proposal
in Section 5.2.2.1.1, Result_request in Section 5.2.2.1.2 and the
Result in Section 5.2.2.1.3.
* The ead_label = TBD4 corresponds to the EAT item trigger_pp as
specified in Section 5.2.2.1.4.
Song Expires 15 August 2025 [Page 19]
Internet-Draft RA-EDHOC February 2025
+-----------+-------+------------------------+-------------------+
| Name | Label | Description | Reference |
+===========+=======+========================+===================+
| TBD | TBD1 | BG model | |
| | | related information | Section 5.2.1.1 |
+-----------+-------+------------------------+-------------------+
| TBD | TBD2 | trigger to start | |
| | | attestation in BG | Secion 5.2.1.1 |
+-----------+-------+------------------------+-------------------+
| TBD | TBD3 | PP model | |
| | | related information | Section 5.2.2.1 |
+-----------+-------+------------------------+-------------------+
| TBD | TBD4 | trigger to start | |
| | | attestation in PP | Secion 5.2.2.1 |
+-----------+-------+------------------------+-------------------+
Figure 5: EAD labels.
11. References
11.1. Normative References
[I-D.ietf-rats-eat]
Lundblade, L., Mandyam, G., O'Donoghue, J., and C.
Wallace, "The Entity Attestation Token (EAT)", Work in
Progress, Internet-Draft, draft-ietf-rats-eat-31, 6
September 2024, <https://datatracker.ietf.org/doc/html/
draft-ietf-rats-eat-31>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/rfc/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.
[RFC9528] Selander, G., Preuß Mattsson, J., and F. Palombini,
"Ephemeral Diffie-Hellman Over COSE (EDHOC)", RFC 9528,
DOI 10.17487/RFC9528, March 2024,
<https://www.rfc-editor.org/rfc/rfc9528>.
11.2. Informative References
[I-D.ietf-lake-authz]
Selander, G., Mattsson, J. P., Vučinić, M., Fedrecheski,
G., and M. Richardson, "Lightweight Authorization using
Song Expires 15 August 2025 [Page 20]
Internet-Draft RA-EDHOC February 2025
Ephemeral Diffie-Hellman Over COSE (ELA)", Work in
Progress, Internet-Draft, draft-ietf-lake-authz-03, 21
October 2024, <https://datatracker.ietf.org/doc/html/
draft-ietf-lake-authz-03>.
[IANA-CoAP-Content-Formats]
"CoAP Content-Formats", n.d.,
<https://www.iana.org/assignments/core-parameters>.
[IANA-COSE-Header-Parameters]
"COSE Header Parameters", n.d.,
<https://www.iana.org/cose/header-parameters>.
[IANA.CWT.Claims]
IANA, "CBOR Web Token (CWT) Claims",
<https://www.iana.org/assignments/cwt>.
[RFC8392] Jones, M., Wahlstroem, E., Erdtman, S., and H. Tschofenig,
"CBOR Web Token (CWT)", RFC 8392, DOI 10.17487/RFC8392,
May 2018, <https://www.rfc-editor.org/rfc/rfc8392>.
[RFC8949] Bormann, C. and P. Hoffman, "Concise Binary Object
Representation (CBOR)", STD 94, RFC 8949,
DOI 10.17487/RFC8949, December 2020,
<https://www.rfc-editor.org/rfc/rfc8949>.
[RFC9334] Birkholz, H., Thaler, D., Richardson, M., Smith, N., and
W. Pan, "Remote ATtestation procedureS (RATS)
Architecture", RFC 9334, DOI 10.17487/RFC9334, January
2023, <https://www.rfc-editor.org/rfc/rfc9334>.
[RFC9393] Birkholz, H., Fitzgerald-McKay, J., Schmidt, C., and D.
Waltermire, "Concise Software Identification Tags",
RFC 9393, DOI 10.17487/RFC9393, June 2023,
<https://www.rfc-editor.org/rfc/rfc9393>.
Appendix A. Example: Remote Attestation Flow
.--------------------------.
| EDHOC Initiator | .-------------------.
+--------------------------+ | EDHOC Responder |
| Attestation | Attester | +-------------------+ .----------.
| Service | | | Relying Party | | Verifier |
'--+----------------+------' '---------+---------' '-----+----'
| | | |
| | | |
| |EDHOC message_1 | |
| | {...} | |
Song Expires 15 August 2025 [Page 21]
Internet-Draft RA-EDHOC February 2025
| | EAD_1( | |
| | types(a,b,c) | |
| | ) | |
| +----------------------->| |
| | | |
| | | types(a,b,c), C_R |
| | +------------------>|
| | | |
| | | |
| | | Body: { |
| | | nonce, |
| | EDHOC message_2 | types(a,b) |
| | {...} | } |
| | EAD_2( |<------------------+
| | nonce, | |
| | type(a) | |
| | ) | |
| | Auth_CRED(Sig/MAC) | |
| |<-----------------------+ |
| Body:{ | | |
| nonce, | | |
| type(a) | | |
| } | | |
|<---------------+ | |
| Body:{ | | |
| Evidence | | |
| } | | |
+--------------->| | |
| | EDHOC message_3 | |
| | {...} | |
| | Evidence(EAT) | |
| | Auth_CRED(sig/MAC) | |
| +----------------------->| |
| | | |
| | | |
| | | |
| | | Body: { |
| | | EAT, C_R} |
| | +------------------>|
| | | Body: { |
| | | att-result: AR{} |
| | | } |
| | |<------------------+
| | +---. |
| | | | verify AR{} |
| | |<--' |
| | | |
| | application data | |
Song Expires 15 August 2025 [Page 22]
Internet-Draft RA-EDHOC February 2025
| |<---------------------->| |
| | | |
Figure 6: Example of remote attestation.
Appendix B. Remote attestation in parallel with enrollment
authorization
This section discusses the possibility of doing remote attestation in
parallel with the enrollment authorization procedure defined in
[I-D.ietf-lake-authz]. In this case, the message count is much
decreased.
The detailed procedure is TBD.
Appendix C. Example: Firmware Version
The goal in this example is to verify that the firmware running on
the device is the latest version, and is neither tampered or
compromised. A device acts as the Attester, currently in an
untrusted state. The Attester needs to generate the evidence to
attest itself. A gateway that can communicate with the Attester and
can control its access to the network acts as the Relying Party. The
gateway will finally decide whether the device can join the network
or not depending on the attestation result. The attestation result
is produced by the Verifier, which is a web server that can be seen
as the manufacturer of the device. Therefore it can appraise the
evidence that is sent by the Attester. The remote attestation
session starts with the Attester sending EAD_1 in EDHOC message 1.
An example of the EAD_1 in EDHOC message_1 could be:
[60,61,258]
If the Verifier and the Relying Party can support at least one
evidence type that is proposed by the Attester, the Relying Party
will include in the EAD_2 field the same evidence type, alongside a
nonce for message freshness.
(258, h'a29f62a4c6cdaae5')
The Evidence in EAD_3 field is an Entity Attestation Token (EAT)
[I-D.ietf-rats-eat], with the measurements claim formatted in
CoSWID[RFC9393]. The components of the Evidence should at least be:
Song Expires 15 August 2025 [Page 23]
Internet-Draft RA-EDHOC February 2025
{
/eat-nonce/ 10: h'a29f62a4c6cdaae5',
/ueid/ 256: 'aaabbcc',
/measurements/ 273: [
/CoAP Content-Format ID/ [ 258,
/evidence in CoSWID/ {
0: 'tagID' /tag-id/
12: 0 /tag-version/
1: "DotBot firmware" /software-name/
2: { /entity/
31: "Attester" /entity-name/
33: 1 /role, must be "tag-creator" which is 1/
},
3: { /evidence/
17: [ /file/
{
24: "partition0-nrf52840dk.bin", /fs-name/
7: [ /hash of file/
1, /alg SHA-256/
h'06294f6806b9c685eea795048579cfd02a0c025bc8b5abca42a19ea0ec23e81a'
] /hash value/
}
]
}
}
]
]
}
The infomation above serves as the payload of the COSE object. The
complete resulting COSE object is:
Song Expires 15 August 2025 [Page 24]
Internet-Draft RA-EDHOC February 2025
18([
/*protected header*/
h'a10127',
/*unprotected header*/
{},
/*payload*/
h'A30A48A29F62A4C6CDAAE519010047616161626263631901118182190102A50045746
16749440C00016F446F74426F74206669726D7761726502A2181F684174746573746572
18210103A11181A218187819706172746974696F6E302D6E72663532383430646B2E626
96E078201582006294F6806B9C685EEA795048579CFD02A0C025BC8B5ABCA42A19EA0EC
23E81A',
/*signature*/
h'd4100901f4c3e51312c3110c6ddc8dcf7f68d8f5d3791c19133f2f0ac158c1f5ee6ed
afe9d7c3d6eb3d2d197f82e733d375fdda9fb258b304961dfc38558950d'
])
which has the following base16 encoding:
D28443A10127A05890A30A48A29F62A4C6CDAAE51901004761616162626363190111818
2190102A5004574616749440C00016F446F74426F74206669726D7761726502A2181F68
417474657374657218210103A11181A218187819706172746974696F6E302D6E7266353
2383430646B2E62696E078201582006294F6806B9C685EEA795048579CFD02A0C025BC8
B5ABCA42A19EA0EC23E81A5840D4100901F4C3E51312C3110C6DDC8DCF7F68D8F5D3791
C19133F2F0AC158C1F5EE6EDAFE9D7C3D6EB3D2D197F82E733D375FDDA9FB258B304961
DFC38558950D
The Relying Party (co-located with the gateway) then treats the
Evidence as opaque and sends it to the Verifier. Once the Verifier
sends back the Attestation Result, the Relying Party can be assured
on the version of the firmware that the device is running.
Appendix D. Open discussion: remote attestation over EDHOC/ over OSCORE
TBD
Acknowledgments
The author would like to thank Thomas Fossati, Goran Selander, Malisa
Vucinic, Ionut Mihalcea, Muhammad Usama Sardar, Michael Richardson
and Geovane Fedrecheski for the provided ideas and feedback.
Author's Address
Yuxuan Song
Inria
Song Expires 15 August 2025 [Page 25]
Internet-Draft RA-EDHOC February 2025
Email: yuxuan.song@inria.fr
Song Expires 15 August 2025 [Page 26]