LISP MIB
draft-ietf-lisp-mib-05
The information below is for an old version of the document.
| Document | Type | Active Internet-Draft (lisp WG) | |
|---|---|---|---|
| Authors | Gregg Schudel , Amit Jain , Victor Moreno | ||
| Last updated | 2012-06-29 | ||
| Replaces | draft-schudel-lisp-mib | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text xml htmlized pdfized bibtex | ||
| Reviews |
GENART Telechat review
(of
-11)
Ready with Nits
SECDIR Last Call review
(of
-08)
Has Nits
|
||
| Stream | WG state | WG Document | |
| Document shepherd | (None) | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-lisp-mib-05
Network Working Group G. Schudel
Internet-Draft A. Jain
Intended status: Experimental V. Moreno
Expires: December 30, 2012 cisco Systems
June 28, 2012
LISP MIB
draft-ietf-lisp-mib-05
Abstract
This document defines managed objects for the Locator/ID Separation
Protocol (LISP). These objects provide information useful for
monitoring LISP devices, including basic configuration information,
LISP status, and operational statistics.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 30, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Schudel, et al. Expires December 30, 2012 [Page 1]
Internet-Draft LISP MIB June 2012
Table of Contents
1. Requirements Notation . . . . . . . . . . . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. The Internet-Standard Management Framework . . . . . . . . . . 3
4. Definition of Terms . . . . . . . . . . . . . . . . . . . . . 4
5. LISP MIB Objectives . . . . . . . . . . . . . . . . . . . . . 6
6. Structure of LISP MIB Module . . . . . . . . . . . . . . . . . 6
6.1. Overview of Defined Notifications . . . . . . . . . . . . 6
6.2. Overview of Defined Tables . . . . . . . . . . . . . . . . 7
7. LISP MIB Definitions . . . . . . . . . . . . . . . . . . . . . 8
8. Relationship to Other MIB Modules . . . . . . . . . . . . . . 57
8.1. MIB modules required for IMPORTS . . . . . . . . . . . . . 57
9. Security Considerations . . . . . . . . . . . . . . . . . . . 57
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 58
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.1. Normative References . . . . . . . . . . . . . . . . . . . 58
11.2. Informative References . . . . . . . . . . . . . . . . . . 59
Appendix A. Open Issues . . . . . . . . . . . . . . . . . . . . . 59
Appendix B. Acknowledgments . . . . . . . . . . . . . . . . . . . 60
Schudel, et al. Expires December 30, 2012 [Page 2]
Internet-Draft LISP MIB June 2012
1. Requirements Notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. Introduction
This draft describes the Management Information Base (MIB) module for
use with network management protocols in the Internet community.
Specifically, the MIB for managing Locator/ID Separation Protocol
(LISP) devices is described.
LISP [LISP] specifies a network-based architecture and mechanisms
that implement a new semantic for IP addressing using two separate
name spaces: Endpoint Identifiers (EIDs), used within sites, and
Routing Locators (RLOCs), used on the transit networks that make up
the Internet infrastructure. To achieve this separation, LISP
defines protocol mechanisms for mapping from EIDs to RLOCs.
From a data plane perspective, LISP traffic is handled exclusively at
the network layer by devices performing Ingress Tunnel Router (ITR)
and Egress Tunnel Router (ETR) LISP functions. Data plane operations
performed by these devices are described in [LISP]. Additionally,
data plane interworking between legacy (Internet) and LISP sites is
implemented by devices performing Proxy ITR (PITR) and Proxy ETR
(PETR) functions. The data plane operations of these devices is
described in [INTERWORK].
From a control plane perspective, LISP employs mechanisms related to
creating, maintaining, and resolving mappings from EIDs to RLOCs.
LISP ITRs, ETRs, PITRs, and PETRs perform specific control plane
functions, and these control plane operations are described in
[LISP]. Additionally, LISP infrastructure devices supporting LISP
control plane functionality include Map-Servers and Map-Resolvers,
and the control plane operations of these devices are described in
[LISP-MS]. Finally, while not specifically required, this document
assumes the existence of a database to store and propagate those
mappings globally.
3. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
Schudel, et al. Expires December 30, 2012 [Page 3]
Internet-Draft LISP MIB June 2012
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
4. Definition of Terms
Endpoint ID (EID): a 32-bit (for IPv4) or 128-bit (for IPv6) value
used in the source and destination address fields of the first
(inner-most) IP header of a LISP packet. A source EID is
allocated to a host from an EID-prefix block associated with the
site where the host is located. A host determines a destination
address in the same way that it determines a destination address
today, for example through a DNS lookup or SIP exchange.
Routing Locator (RLOC): a 32-bit (for IPv4) or 128-bit (for IPv6)
value used in the source and destination address fields of the
second (outer-most) IP header of a LISP packet. RLOC addresses
are allocated to an egress tunnel router (ETR) and numbered from
topologically-aggregatable blocks assigned to a site at each point
to which it attaches to the global Internet.
EID-to-RLOC Map-Cache: a short-lived, on-demand table maintained
locally in an ITR or PITR that stores, tracks, and is responsible
for timing-out and otherwise validating EID-to-RLOC mappings.
This table is distinct from the full "database" of EID-to-RLOC
mappings in that it is dynamic and relatively small. At a given
moment in time, it consists only of entries for those sites to
which the ITR or PITR is currently communicating or has
communicated with within the configured TTL period.
EID-to-RLOC Mapping-Database: a global distributed database that
contains all known EID-to-RLOC mappings. Each potential ETR
typically contains a small piece of the database consisting of
only the EID-to-RLOC mappings for the EID prefix(es) for which the
ETR is "authoritative" and the RLOC(s) by which those EID
prefix(es) are reachable from the global Internet.
Ingress Tunnel Router (ITR): a router that accepts an IP packet with
a single IP header (more precisely, an IP packet that does not
contain a LISP header), treats this "inner" IP destination address
as an EID and performs an EID-to-RLOC mapping lookup, and then
prepends an "outer" IP header with one of its own globally-
routable RLOCs in the source address field and the RLOC resulting
from the mapping lookup in the destination address field. That
is, in general an ITR receives an IP packet from site end-systems
Schudel, et al. Expires December 30, 2012 [Page 4]
Internet-Draft LISP MIB June 2012
on one side and sends a LISP-encapsulated IP packet toward the
Internet on the other side.
Egress Tunnel Router (ETR): a router that accepts an IP packet where
the destination address in the "outer" IP header is one of its own
RLOCs, strips the "outer" header, and forwards the packet based on
the next IP header found. That is, in general an ETR receives
LISP-encapsulated IP packets from the Internet on one side and
sends decapsulated IP packets toward site end-systems on the other
side.
xTR: a term of general reference to an ITR or ETR when direction of
data flow is not part of the context description. xTR refers to
the router that is the tunnel endpoint and performs both ITR and
ETR functionality. For example, "An xTR can be located at the
Customer Edge (CE) router," meaning both ITR and ETR functionality
is activated at the CE router.
Proxy ITR (PITR): a router that acts like an ITR but does so on
behalf of non-LISP sites which send packets to destinations at
LISP sites. The PITR, also known as a PTR, is defined and
described in [INTERWORK].
Proxy ETR (PETR): a router that acts like an ETR but does so on
behalf of LISP sites which send packets to destinations at non-
LISP sites. The PETR is defined and described in [INTERWORK].
LISP Site: a set of routers in an edge network that are under a
single technical administration. LISP routers which reside in the
edge network are the demarcation points to separate the edge
network from the core network.
Map-Server: a LISP network infrastructure component which learns
EID-to-RLOC mapping entries from an authoritative source such as
an ETR though static configuration, or another out-of-band
mechanism. A Map-Server advertises these mappings into the
distributed mapping database.
Map-Resolver: a LISP network infrastructure component which accepts
LISP Encapsulated Map-Requests, typically from an ITR, and quickly
determines whether or not the destination IP address is part of
the EID namespace. If it is, the Map-Resolver finds the
appropriate EID-to-RLOC mapping by consulting the distributed
mapping database. If it is not, a Negative Map-Reply is
immediately returned.
Schudel, et al. Expires December 30, 2012 [Page 5]
Internet-Draft LISP MIB June 2012
Map-Request: a LISP Map-Request message type sent by an ITR or PITR
to a Map-Resolver when it needs a mapping for an EID, wants to
test an RLOC for reachability, or wants to refresh a mapping
before TTL expiration.
Map-Reply: a LISP Map-Reply message type returned in response to a
Map-Request for a destination EID that exists in the mapping
database and contains the locator-set and associated policy for
the queried EID. Information returned in a Map-Reply is stored in
the EID-to-RLOC Map-Cache.
Negative Map-Reply: a LISP Map-Reply message type that contains an
empty locator-set. Returned in response to a Map-Request if the
destination EID does not exist in the mapping database.
Typically, this means that the "EID" being requested is an IP
address connected to a non-LISP site. Information returned in a
Negative Map-Reply is stored in the EID-to-RLOC Map-Cache.
5. LISP MIB Objectives
The objectives for defining this LISP MIB module are as follows:
o Provide a means for obtaining a list of enabled LISP features and
the current status of configuration attributes related to those
features. As an example, LISP capabilities which could be enabled
include ITR, ETR, PITR, PETR, MS or MR support for IPv4 or IPv6
address families. Other examples include, indicating whether
rloc-probing is enabled, and indicating the configured map-cache
limit value.
o Provide a means for obtaining the current attributes of various
LISP tables, such as the EID-to-RLOC policy data contained in the
Map-Cache, or the local EID-to-RLOC policy data contained in the
Mapping-Database.
o Provide a means for obtaining the current operational statistics
of various LISP functions, such as the number of packets
encapsulated and decapsulated by the device. Other counters of
operational interest, depending on LISP function, include things
like the current number of map-cache entries, and the total number
and rate of map-requests received and sent.
6. Structure of LISP MIB Module
6.1. Overview of Defined Notifications
No LISP MIB notifications are defined.
Schudel, et al. Expires December 30, 2012 [Page 6]
Internet-Draft LISP MIB June 2012
6.2. Overview of Defined Tables
The LISP MIB module is composed of the following tables of objects:
lispFeatures - This table provides information representing the
various lisp features that can be enabled on LISP devices.
lispIidToVrf - This table provides information representing the
mapping of LISP instance ID to a VRF.
lispGlobalStats - This table provides global statistics for a given
Instance ID per address-family on a LISP device.
lispMappingDatabase - This table represents the EID-to-RLOC database
that contains the EID-prefix to RLOC mappings configured on an
ETR. In general, this table would be representative of all such
mappings for a given site that this device belongs to.
lispMappingDatabaseLocator - This table represents the set of
routing locators contained in the EID-to-RLOC database configured
on an ETR.
lispMapCache - This table represents the short-lived, on-demand
table on an ITR that stores, tracks, and is responsible for
timing-out and otherwise validating EID-to-RLOC mappings.
lispMapCacheLocator - This table represents the set of locators per
EID prefix contained in the map-cache table of an ITR.
lispConfiguredLocator - This table represents the set of routing
locators configured on a LISP device.
lispEidRegistration - This table provides the properties of each EID
prefix that is registered with this device when configured to be a
Map-Server.
lispEidRegistrationEtr - This table provides the properties of the
different ETRs that send registers, for a given EID prefix, to
this device when configured to be a Map-Server.
lispEidRegistrationLocator - This table provides the properties of
the different locators per EID prefix that is registered with this
device when configured to be a Map-Server.
lispUseMapServer - This table provides the properties of all Map-
Servers that this device is configured to use.
Schudel, et al. Expires December 30, 2012 [Page 7]
Internet-Draft LISP MIB June 2012
lispUseMapResolver - This table provides the properties of all Map-
Resolvers that this device is configured to use.
lispUseProxyEtr - This table provides the properties of all Proxy
ETRs that this device is configured to use.
7. LISP MIB Definitions
LISP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
mib-2, Unsigned32, Counter64,
Integer32, TimeTicks FROM SNMPv2-SMI -- [RFC 2578]
TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC -- [RFC 2579]
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC 2580]
VPNIdOrZero FROM VPN-TC-STD-MIB -- [RFC 4265]
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB; -- [IANA]
lispMIB MODULE-IDENTITY
LAST-UPDATED "201206280000Z" -- 28 June 2012
ORGANIZATION
"IETF Locator/ID Separation Protocol (LISP) Working Group"
CONTACT-INFO
"Email: lisp@ietf.org
WG charter:
http://www.ietf.org/html.charters/lisp-charter.html"
DESCRIPTION
"Locator/ID Separation Protocol (LISP) MIB Textual
Conventions module. The LISP MIB is intended for
management of LISP routers.
Copyright (C) The IETF Trust (2012)."
REVISION "201206280000Z" -- 28 June 2012
DESCRIPTION "Initial version of the IETF LISP-MIB module"
::= { mib-2 xxx }
--
-- Textual Conventions
--
LispAddressType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"LISP architecture can be applied to a wide variety of
address-families. This textual-convention is a
Schudel, et al. Expires December 30, 2012 [Page 8]
Internet-Draft LISP MIB June 2012
generalization for representing addresses that belong
to those address-families. For convenience, this
document refers to any such address as a LISP address.
LispAddressType textual-convention consists of
the following four-tuple:
1. IANA Address Family Number: A field of length
2-octets, whose value is of the form following the
assigned AddressFamilyNumbers textual-convention
described in [IANA]. The enumerations are listed
in [IANA]. Note that this list of address family
numbers is maintained by IANA.
2. Length of LISP address: A field of length 1-octet,
whose value indicates the octet-length of the next
(third) field of this LispAddressType four-tuple.
3. LISP address: A field of variable length as
indicated in the previous (second) field, whose
value is an address of the IANA Address Family
indicated in the first field of this LispAddressType
four-tuple. Note that any of the IANA Address
Families can be represented. Particularly when the
address family is LISP Canonical Address Format
(LCAF) [LCAF] with IANA assigned Address Family
Number 16387, then the first octet of this field
indicates the LCAF type, and the rest of this field
is same as the encoding format of the LISP Canonical
Address after the length field, as defined in [LCAF].
4. Mask-length of address: A variable-length field
comprised of the remaining octets of this
LispAddressType four-tuple, whose value is the
mask-length to be applied to the LISP address
specified in the previous (third) field.
To illustrate the use of this object, consider the
LISP MIB Object below entitled lispMapCacheEntry.
This object begins with the following entities:
lispMapCacheEntry ::= SEQUENCE {
lispMapCacheEidLength INTEGER,
lispMapCacheEid LispAddressType,
... [skip] ...
Example 1: Suppose that the IPv4 EID prefix stored is
10.10.10.0/24. In this case, the values within
lispMapCacheEntry would be:
lispMapCacheEidLength = 8
lispMapCacheEid = 1, 4, 10.10.10.0, 24
... [skip] ...
Schudel, et al. Expires December 30, 2012 [Page 9]
Internet-Draft LISP MIB June 2012
where 8 is the total length in octets of the next
object (lispMapCacheEID of type LispAddressType). Then,
the value 1 indicates the IPv4 AF (per [IANA]), the
value 4 indicates that the AF is 4-octets in length,
10.10.10.0 is the IPv4 address, and the value 24 is the
mask-length in bits. Note that the lispMapCacheEidLength
value of 8 is used to compute the length of the fourth
(last) field in lispMapCacheEid to be 1 octet - as
computed by 8 - (2 + 1 + 4) = 1.
Example 2: Suppose that the IPv6 EID prefix stored is
2001:db8:a::/48. In this case, the values within
lispMapCacheEntry would be:
lispMapCacheEidLength = 20
lispMapCacheEid = 2, 16, 2001:db8:a::, 48
... [skip] ...
where 20 is the total length in octets of the next
object (lispMapCacheEID of type LispAddressType). Then,
the value 2 indicates the IPv4 AF (per [IANA]), the
value 16 indicates that the AF is 16-octets in length,
2001:db8:a:: is the IPv6 address, and the value 48 is the
mask-length in bits. Note that the lispMapCacheEidLength
value of 20 is used to compute the length of the fourth
(last) field in lispMapCacheEid to be 1 octet - as
computed by 20 - (2 + 1 + 16) = 1.
Example 3: As an example where LCAF is used, suppose
that the IPv4 EID prefix stored is 10.10.10.0/24 and it
is part of LISP Instance ID 101. In this case, the values
within lispMapCacheEntry would be:
lispMapCacheEidLength = 11
lispMapCacheEid = 16387, 7, 2, 101, 1, 10.10.10.0, 24
... [skip] ...
where 11 is the total length in octets of the next object
(lispMapCacheEID of type LispAddressType). Then, the value
16387 indicates the LCAF AF (see [IANA]), the value 7
indicates that the LCAF AF is 7-octets in length in this
case, 2 indicates that LCAF Type 2 encoding is used (see
[LCAF]), 101 gives the Instance ID, 1 gives the AFI (per
[IANA]) for an IPv4 address, 10.10.10.0 is the IPv4
address, and 24 is the mask-length in bits. Note that the
lispMapCacheEidLength value of 11 octets is used to compute
the length of the last field in lispMapCacheEid to be 1 octet,
Schudel, et al. Expires December 30, 2012 [Page 10]
Internet-Draft LISP MIB June 2012
as computed by 11 - (2 + 1 + 1 + 1 + 1 + 1 + 4) = 1."
REFERENCE "[LISP]"
SYNTAX OCTET STRING (SIZE (0..1024))
--
-- Top level components of this MIB.
--
lispObjects OBJECT IDENTIFIER ::= { lispMIB 1 }
lispConformance OBJECT IDENTIFIER ::= { lispMIB 2 }
lispFeaturesTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispFeaturesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the various LISP features
that can be enabled on LISP devices."
REFERENCE "[LISP]"
::= { lispObjects 1 }
lispFeaturesEntry OBJECT-TYPE
SYNTAX LispFeaturesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispFeaturesTable."
INDEX { lispFeaturesInstanceID,
lispFeaturesAddressFamily }
::= { lispFeaturesTable 1 }
LispFeaturesEntry ::= SEQUENCE {
lispFeaturesInstanceID Unsigned32,
lispFeaturesAddressFamily AddressFamilyNumbers,
lispFeaturesItrEnabled TruthValue,
lispFeaturesEtrEnabled TruthValue,
lispFeaturesProxyItrEnabled TruthValue,
lispFeaturesProxyEtrEnabled TruthValue,
lispFeaturesMapServerEnabled TruthValue,
lispFeaturesMapResolverEnabled TruthValue,
lispFeaturesMapCacheSize Unsigned32,
lispFeaturesMapCacheLimit Unsigned32,
lispFeaturesEtrMapCacheTtl Unsigned32,
lispFeaturesRlocProbeEnabled TruthValue,
Schudel, et al. Expires December 30, 2012 [Page 11]
Internet-Draft LISP MIB June 2012
lispFeaturesEtrAcceptMapDataEnabled TruthValue,
lispFeaturesEtrAcceptMapDataVerifyEnabled TruthValue
}
lispFeaturesInstanceID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This represents the Instance ID of the LISP
header. An Instance ID in the LISP address
encoding helps uniquely identify the AFI-based
address space to which a given EID belongs.
It's default value is 0."
::= { lispFeaturesEntry 1 }
lispFeaturesAddressFamily OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address family number that the LISP device
is enabled to LISP process a packet for as a
destination address family."
::= { lispFeaturesEntry 2 }
lispFeaturesItrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of ITR role on this device. If
this object is TRUE, then ITR feature is enabled."
::= { lispFeaturesEntry 3 }
lispFeaturesEtrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of ETR role on this device. If
this object is TRUE, then ETR feature is enabled."
::= { lispFeaturesEntry 4 }
lispFeaturesProxyItrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
Schudel, et al. Expires December 30, 2012 [Page 12]
Internet-Draft LISP MIB June 2012
STATUS current
DESCRIPTION
"Indicates the status of Proxy-ITR role on this device.
If this object is TRUE, then Proxy-ITR feature is enabled."
::= { lispFeaturesEntry 5 }
lispFeaturesProxyEtrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Proxy-ETR role on this device.
If this object is TRUE, then Proxy-ETR feature is enabled."
::= { lispFeaturesEntry 6 }
lispFeaturesMapServerEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Map Server role on this device.
If this object is TRUE, then Map Server feature is enabled."
::= { lispFeaturesEntry 7 }
lispFeaturesMapResolverEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Map Resolver role on this device.
If this object is TRUE, then Map Resolver feature is enabled."
::= { lispFeaturesEntry 8 }
lispFeaturesMapCacheSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Size of EID-to-RLOC map cache on this device."
::= { lispFeaturesEntry 9 }
lispFeaturesMapCacheLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum permissible size of EID-to-RLOC map
Schudel, et al. Expires December 30, 2012 [Page 13]
Internet-Draft LISP MIB June 2012
cache on this device."
::= { lispFeaturesEntry 10 }
lispFeaturesEtrMapCacheTtl OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time in minutes this device will store the
EID-to-RLOC map record in the map cache."
::= { lispFeaturesEntry 11 }
lispFeaturesRlocProbeEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of rloc-probing feature
on this device, If this object is TRUE, then
this feature is enabled."
::= { lispFeaturesEntry 12 }
lispFeaturesEtrAcceptMapDataEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of accepting piggybacked
mapping data received in a map-request on
this device. If this object is TRUE, then this
device accepts piggybacked mapping data."
::= { lispFeaturesEntry 13 }
lispFeaturesEtrAcceptMapDataVerifyEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of verifying accepted
piggybacked mapping data received in a
map-request on this device. If this object is
TRUE, then this device verifies accepted
piggybacked mapping data."
::= { lispFeaturesEntry 14 }
Schudel, et al. Expires December 30, 2012 [Page 14]
Internet-Draft LISP MIB June 2012
lispIidToVrfTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispIidToVrfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the mapping of LISP Instance ID
to a VRF."
REFERENCE "[LISP]"
::= { lispObjects 2 }
lispIidToVrfEntry OBJECT-TYPE
SYNTAX LispIidToVrfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispIidToVrfTable."
INDEX { lispFeaturesInstanceID }
::= { lispIidToVrfTable 1 }
LispIidToVrfEntry ::= SEQUENCE {
lispIidToVrfVpnId VPNIdOrZero
}
lispIidToVrfVpnId OBJECT-TYPE
SYNTAX VPNIdOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The VPN ID, as specified in [RFC2685], that is mapped
to the given LISP Instance ID. If a VPN ID has not been
specified for this VRF, then this variable SHOULD be
set to a zero-length OCTET STRING."
::= { lispIidToVrfEntry 1 }
lispGlobalStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispGlobalStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides global statistics for a given
Instance ID per address-family on a LISP device."
REFERENCE "[LISP]"
::= { lispObjects 3 }
lispGlobalStatsEntry OBJECT-TYPE
Schudel, et al. Expires December 30, 2012 [Page 15]
Internet-Draft LISP MIB June 2012
SYNTAX LispGlobalStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispGlobalStatsTable."
INDEX { lispFeaturesInstanceID,
lispFeaturesAddressFamily }
::= { lispGlobalStatsTable 1 }
LispGlobalStatsEntry ::= SEQUENCE {
lispGlobalStatsMapRequestsIn Counter64,
lispGlobalStatsMapRequestsOut Counter64,
lispGlobalStatsMapRepliesIn Counter64,
lispGlobalStatsMapRepliesOut Counter64,
lispGlobalStatsMapRegistersIn Counter64,
lispGlobalStatsMapRegistersOut Counter64
}
lispGlobalStatsMapRequestsIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map requests received by this
device for any EID prefix of the given address
family and Instance ID."
::= { lispGlobalStatsEntry 1 }
lispGlobalStatsMapRequestsOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map requests sent by this
device for any EID prefix of the given
address family and Instance ID."
::= { lispGlobalStatsEntry 2 }
lispGlobalStatsMapRepliesIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map replies received by this
device for any EID prefix of the given
address family and Instance ID."
::= { lispGlobalStatsEntry 3 }
Schudel, et al. Expires December 30, 2012 [Page 16]
Internet-Draft LISP MIB June 2012
lispGlobalStatsMapRepliesOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map replies sent by this
device for any EID prefix of the given
address family and Instance ID."
::= { lispGlobalStatsEntry 4 }
lispGlobalStatsMapRegistersIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map registers received by this
device for any EID prefix of the given address
family and Instance ID."
::= { lispGlobalStatsEntry 5 }
lispGlobalStatsMapRegistersOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map registers sent by this
device for any EID prefix of the given
address family and Instance ID."
::= { lispGlobalStatsEntry 6 }
lispMappingDatabaseTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMappingDatabaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the EID-to-RLOC mapping
database that contains the EID-prefix to RLOC
mappings configured on an ETR. In general,
this table would be representative of all such
mappings for the given LISP site to which this
device belongs."
REFERENCE "[LISP]"
::= { lispObjects 4 }
lispMappingDatabaseEntry OBJECT-TYPE
SYNTAX LispMappingDatabaseEntry
Schudel, et al. Expires December 30, 2012 [Page 17]
Internet-Draft LISP MIB June 2012
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMappingDatabaseTable."
INDEX { lispMappingDatabaseEidLength,
lispMappingDatabaseEid }
::= { lispMappingDatabaseTable 1 }
LispMappingDatabaseEntry ::= SEQUENCE {
lispMappingDatabaseEidLength Integer32,
lispMappingDatabaseEid LispAddressType,
lispMappingDatabaseLsb Unsigned32,
lispMappingDatabaseEidPartitioned TruthValue,
lispMappingDatabaseDecapOctets Counter64,
lispMappingDatabaseDecapPackets Counter64,
lispMappingDatabaseEncapOctets Counter64,
lispMappingDatabaseEncapPackets Counter64
}
lispMappingDatabaseEidLength OBJECT-TYPE
SYNTAX Integer32 (0..1024)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object gives the octet-length of
lispMappingDatabaseEid."
::= { lispMappingDatabaseEntry 1 }
lispMappingDatabaseEid OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The EID prefix of the mapping database."
::= { lispMappingDatabaseEntry 2 }
lispMappingDatabaseLsb OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The locator status bits for this EID prefix."
::= { lispMappingDatabaseEntry 3 }
lispMappingDatabaseEidPartitioned OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
Schudel, et al. Expires December 30, 2012 [Page 18]
Internet-Draft LISP MIB June 2012
STATUS current
DESCRIPTION
"Indicates if this device is partitioned from
the site that contains this EID prefix. If this
object is TRUE, then it means this device is
partitioned from the site."
::= { lispMappingDatabaseEntry 4 }
lispMappingDatabaseDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that
were decapsulated by this device addressed
to a host within this EID-prefix."
::= { lispMappingDatabaseEntry 5 }
lispMappingDatabaseDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were
decapsulated by this device addressed to a
host within this EID-prefix."
::= { lispMappingDatabaseEntry 6 }
lispMappingDatabaseEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets, that
were encapsulated by this device, whose inner
header source address matched this EID prefix."
::= { lispMappingDatabaseEntry 7 }
lispMappingDatabaseEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were
encapsulated by this device that whose inner
header source address matched this EID prefix."
::= { lispMappingDatabaseEntry 8 }
Schudel, et al. Expires December 30, 2012 [Page 19]
Internet-Draft LISP MIB June 2012
lispMappingDatabaseLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMappingDatabaseLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the set of routing locators
per EID prefix contained in the EID-to-RLOC
database configured on this ETR."
REFERENCE "[LISP]"
::= { lispObjects 5 }
lispMappingDatabaseLocatorEntry OBJECT-TYPE
SYNTAX LispMappingDatabaseLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMappingDatabaseLocatorTable."
INDEX { lispMappingDatabaseEidLength,
lispMappingDatabaseEid,
lispMappingDatabaseLocatorRlocLength,
lispMappingDatabaseLocatorRloc }
::= { lispMappingDatabaseLocatorTable 1 }
LispMappingDatabaseLocatorEntry ::= SEQUENCE {
lispMappingDatabaseLocatorRlocLength Integer32,
lispMappingDatabaseLocatorRloc LispAddressType,
lispMappingDatabaseLocatorRlocPriority Integer32,
lispMappingDatabaseLocatorRlocWeight Integer32,
lispMappingDatabaseLocatorRlocMPriority Integer32,
lispMappingDatabaseLocatorRlocMWeight Integer32,
lispMappingDatabaseLocatorRlocState INTEGER,
lispMappingDatabaseLocatorRlocLocal INTEGER,
lispMappingDatabaseLocatorRlocDecapOctets Counter64,
lispMappingDatabaseLocatorRlocDecapPackets Counter64,
lispMappingDatabaseLocatorRlocEncapOctets Counter64,
lispMappingDatabaseLocatorRlocEncapPackets Counter64
}
lispMappingDatabaseLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispMappingDatabaseLocatorRloc, the next object."
::= { lispMappingDatabaseLocatorEntry 1 }
Schudel, et al. Expires December 30, 2012 [Page 20]
Internet-Draft LISP MIB June 2012
lispMappingDatabaseLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is a locator for the given EID prefix
in the mapping database."
::= { lispMappingDatabaseLocatorEntry 2 }
lispMappingDatabaseLocatorRlocPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the RLOC."
::= { lispMappingDatabaseLocatorEntry 3 }
lispMappingDatabaseLocatorRlocWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the RLOC."
::= { lispMappingDatabaseLocatorEntry 4 }
lispMappingDatabaseLocatorRlocMPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the RLOC."
::= { lispMappingDatabaseLocatorEntry 5 }
lispMappingDatabaseLocatorRlocMWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the RLOC."
::= { lispMappingDatabaseLocatorEntry 6 }
lispMappingDatabaseLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2),
unreachable (3)
}
MAX-ACCESS read-only
Schudel, et al. Expires December 30, 2012 [Page 21]
Internet-Draft LISP MIB June 2012
STATUS current
DESCRIPTION
"The state of this RLOC as per this device.
(1 = RLOC is up; 2 = RLOC is down;
3 = RLOC is unreachable)."
::= { lispMappingDatabaseLocatorEntry 7 }
lispMappingDatabaseLocatorRlocLocal OBJECT-TYPE
SYNTAX INTEGER {
siteself (1),
sitelocal (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the RLOC is local to this
device (or remote, meaning local to another
device in the same LISP site). (1 = RLOC is
an address on this device; 2 = RLOC is an
address on another device)."
::= { lispMappingDatabaseLocatorEntry 8 }
lispMappingDatabaseLocatorRlocDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
addressed to this RLOC of the EID-prefix and
were decapsulated."
::= { lispMappingDatabaseLocatorEntry 9 }
lispMappingDatabaseLocatorRlocDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were addressed
to this RLOC of the EID-prefix and were
decapsulated."
::= { lispMappingDatabaseLocatorEntry 10 }
lispMappingDatabaseLocatorRlocEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
Schudel, et al. Expires December 30, 2012 [Page 22]
Internet-Draft LISP MIB June 2012
encapsulated by this device using this RLOC
address as the source, and that were sourced
by an address of this EID-prefix."
::= { lispMappingDatabaseLocatorEntry 11 }
lispMappingDatabaseLocatorRlocEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were
encapsulated by this device using this RLOC
address as the source, and that were sourced
by an address of this EID-prefix."
::= { lispMappingDatabaseLocatorEntry 12 }
lispMapCacheTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMapCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the short-lived, on-demand
table on an ITR that stores, tracks, and is
responsible for timing-out and otherwise
validating EID-to-RLOC mappings."
REFERENCE "[LISP]"
::= { lispObjects 6 }
lispMapCacheEntry OBJECT-TYPE
SYNTAX LispMapCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMapCacheTable."
INDEX { lispMapCacheEidLength,
lispMapCacheEid }
::= { lispMapCacheTable 1 }
LispMapCacheEntry ::= SEQUENCE {
lispMapCacheEidLength Integer32,
lispMapCacheEid LispAddressType,
lispMapCacheEidUpTime TimeTicks,
lispMapCacheEidExpiryTime TimeTicks,
lispMapCacheEidState TruthValue,
lispMapCacheEidAuthoritative TruthValue,
lispMapCacheDecapOctets Counter64,
Schudel, et al. Expires December 30, 2012 [Page 23]
Internet-Draft LISP MIB June 2012
lispMapCacheDecapPackets Counter64,
lispMapCacheEncapOctets Counter64,
lispMapCacheEncapPackets Counter64
}
lispMapCacheEidLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispMapCacheEid, the next object."
::= { lispMapCacheEntry 1 }
lispMapCacheEid OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The EID prefix in the mapping cache."
::= { lispMapCacheEntry 2 }
lispMapCacheEidUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The up time of the EID prefix."
::= { lispMapCacheEntry 3 }
lispMapCacheEidExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the ITR times-out
this EID prefix."
::= { lispMapCacheEntry 4 }
lispMapCacheEidState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to indicate the activity
of this EID prefix. If this object is TRUE, then
it means this EID prefix is seeing activity."
::= { lispMapCacheEntry 5 }
Schudel, et al. Expires December 30, 2012 [Page 24]
Internet-Draft LISP MIB June 2012
lispMapCacheEidAuthoritative OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to indicate whether the EID
prefix was installed by an authoritative map-reply.
If this object is TRUE, then it means this EID
prefix was installed by an authoritative map-reply."
::= { lispMapCacheEntry 6 }
lispMapCacheDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
decapsulated by this device and were sourced
from a remote host within this EID-prefix."
::= { lispMapCacheEntry 7 }
lispMapCacheDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were
decapsulated by this device and were sourced
from a remote host within this EID-prefix."
::= { lispMapCacheEntry 8 }
lispMapCacheEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
encapsulated by this device using the given
EID-prefix in the map cache."
::= { lispMapCacheEntry 9 }
lispMapCacheEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were encapsulated
by this device using the given EID-prefix in the
Schudel, et al. Expires December 30, 2012 [Page 25]
Internet-Draft LISP MIB June 2012
map cache."
::= { lispMapCacheEntry 10 }
lispMapCacheLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMapCacheLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the set of locators per EID
prefix contained in the map-cache table of an ITR."
REFERENCE "[LISP]"
::= { lispObjects 7 }
lispMapCacheLocatorEntry OBJECT-TYPE
SYNTAX LispMapCacheLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMapCacheLocatorTable."
INDEX { lispMapCacheEidLength,
lispMapCacheEid,
lispMapCacheLocatorRlocLength,
lispMapCacheLocatorRloc }
::= { lispMapCacheLocatorTable 1 }
LispMapCacheLocatorEntry ::= SEQUENCE {
lispMapCacheLocatorRlocLength Integer32,
lispMapCacheLocatorRloc LispAddressType,
lispMapCacheLocatorRlocPriority Integer32,
lispMapCacheLocatorRlocWeight Integer32,
lispMapCacheLocatorRlocMPriority Integer32,
lispMapCacheLocatorRlocMWeight Integer32,
lispMapCacheLocatorRlocState INTEGER,
lispMapCacheLocatorRlocUpTime TimeTicks,
lispMapCacheLocatorRlocLastPriorityChange TimeTicks,
lispMapCacheLocatorRlocLastWeightChange TimeTicks,
lispMapCacheLocatorRlocLastMPriorityChange TimeTicks,
lispMapCacheLocatorRlocLastMWeightChange TimeTicks,
lispMapCacheLocatorRlocLastStateChange TimeTicks,
lispMapCacheLocatorRlocRtt TimeTicks,
lispMapCacheLocatorRlocDecapOctets Counter64,
lispMapCacheLocatorRlocDecapPackets Counter64,
lispMapCacheLocatorRlocEncapOctets Counter64,
lispMapCacheLocatorRlocEncapPackets Counter64
}
Schudel, et al. Expires December 30, 2012 [Page 26]
Internet-Draft LISP MIB June 2012
lispMapCacheLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispMapCacheLocatorRloc, the next object."
::= { lispMapCacheLocatorEntry 1 }
lispMapCacheLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locator for the EID prefix in the mapping cache."
::= { lispMapCacheLocatorEntry 2 }
lispMapCacheLocatorRlocPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the RLOC for this EID prefix
(0-255) lower more preferred. "
::= { lispMapCacheLocatorEntry 3 }
lispMapCacheLocatorRlocWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the RLOC for this EID prefix
(0 - 100) percentage. "
::= { lispMapCacheLocatorEntry 4 }
lispMapCacheLocatorRlocMPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the RLOC for this EID prefix."
::= { lispMapCacheLocatorEntry 5 }
lispMapCacheLocatorRlocMWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Schudel, et al. Expires December 30, 2012 [Page 27]
Internet-Draft LISP MIB June 2012
"The multicast weight of the RLOC for this EID prefix."
::= { lispMapCacheLocatorEntry 6 }
lispMapCacheLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this RLOC as per this device
(1 = RLOC is up; 2 = RLOC is down)."
::= { lispMapCacheLocatorEntry 7 }
lispMapCacheLocatorRlocUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The up-time of this RLOC."
::= { lispMapCacheLocatorEntry 8 }
lispMapCacheLocatorRlocLastPriorityChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the unicast priority
of the RLOC for this EID prefix."
::= { lispMapCacheLocatorEntry 9 }
lispMapCacheLocatorRlocLastWeightChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the unicast weight of
the RLOC for this EID prefix."
::= { lispMapCacheLocatorEntry 10 }
lispMapCacheLocatorRlocLastMPriorityChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the multicast
priority of the RLOC for this EID prefix."
Schudel, et al. Expires December 30, 2012 [Page 28]
Internet-Draft LISP MIB June 2012
::= { lispMapCacheLocatorEntry 11 }
lispMapCacheLocatorRlocLastMWeightChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the multicast weight
of the RLOC for this EID prefix."
::= { lispMapCacheLocatorEntry 12 }
lispMapCacheLocatorRlocLastStateChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the up/down state of
the RLOC for this EID prefix."
::= { lispMapCacheLocatorEntry 13 }
lispMapCacheLocatorRlocRtt OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Round trip time of RLOC probe and map-reply for
this RLOC address for this prefix."
::= { lispMapCacheLocatorEntry 14 }
lispMapCacheLocatorRlocDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
decapsulated by this device and were sourced
from a remote host within this EID-prefix and
were encapsulated for this RLOC."
::= { lispMapCacheLocatorEntry 15 }
lispMapCacheLocatorRlocDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were decapsulated
by this device and were sourced from a remote host
within this EID-prefix and were encapsulated for
Schudel, et al. Expires December 30, 2012 [Page 29]
Internet-Draft LISP MIB June 2012
this RLOC."
::= { lispMapCacheLocatorEntry 16 }
lispMapCacheLocatorRlocEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that matched
this EID-prefix and were encapsulated using this
RLOC address."
::= { lispMapCacheLocatorEntry 17 }
lispMapCacheLocatorRlocEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that matched this EID
prefix and were encapsulated using this RLOC address."
::= { lispMapCacheLocatorEntry 18 }
lispConfiguredLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispConfiguredLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the set of routing locators
configured on this device. Note that the Proxy-ITR
configured addresses are treated as routing locators
and therefore can be part of this table."
REFERENCE "[LISP]"
::= { lispObjects 8 }
lispConfiguredLocatorEntry OBJECT-TYPE
SYNTAX LispConfiguredLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispConfiguredLocatorTable."
INDEX { lispConfiguredLocatorRlocLength,
lispConfiguredLocatorRloc }
::= { lispConfiguredLocatorTable 1 }
LispConfiguredLocatorEntry ::= SEQUENCE {
Schudel, et al. Expires December 30, 2012 [Page 30]
Internet-Draft LISP MIB June 2012
lispConfiguredLocatorRlocLength Integer32,
lispConfiguredLocatorRloc LispAddressType,
lispConfiguredLocatorRlocState INTEGER,
lispConfiguredLocatorRlocLocal INTEGER,
lispConfiguredLocatorRlocDecapOctets Counter64,
lispConfiguredLocatorRlocDecapPackets Counter64,
lispConfiguredLocatorRlocEncapOctets Counter64,
lispConfiguredLocatorRlocEncapPackets Counter64
}
lispConfiguredLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispConfiguredLocatorRloc, the next object."
::= { lispConfiguredLocatorEntry 1 }
lispConfiguredLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is a RLOC address configured on this
device. It can be an RLOC that is local to this
device or can be an RLOC which belongs to another
ETR within the same site. Proxy-ITR address is
treated as an RLOC."
::= { lispConfiguredLocatorEntry 2 }
lispConfiguredLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2),
unreachable (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this RLOC as per this device.
(1 = RLOC is up; 2 = RLOC is down;
3 = RLOC is unreachable)."
::= { lispConfiguredLocatorEntry 3 }
lispConfiguredLocatorRlocLocal OBJECT-TYPE
SYNTAX INTEGER {
siteself (1),
Schudel, et al. Expires December 30, 2012 [Page 31]
Internet-Draft LISP MIB June 2012
sitelocal (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the RLOC is local to this
device (or remote, meaning local to another
device in the same LISP site). (1 = RLOC is
an address on this device; 2 = RLOC is an
address on another device)."
::= { lispConfiguredLocatorEntry 4 }
lispConfiguredLocatorRlocDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
addressed to this RLOC and were decapsulated."
::= { lispConfiguredLocatorEntry 5 }
lispConfiguredLocatorRlocDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were addressed
to this RLOC and were decapsulated."
::= { lispConfiguredLocatorEntry 6 }
lispConfiguredLocatorRlocEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
encapsulated by this device using this RLOC
address as the source."
::= { lispConfiguredLocatorEntry 7 }
lispConfiguredLocatorRlocEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were
encapsulated by this device using this RLOC
Schudel, et al. Expires December 30, 2012 [Page 32]
Internet-Draft LISP MIB June 2012
address as the source."
::= { lispConfiguredLocatorEntry 8 }
lispEidRegistrationTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispEidRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of each LISP EID
prefix that is registered with this device when
configured to be a Map-Server."
REFERENCE "[LISP]"
::= { lispObjects 9 }
lispEidRegistrationEntry OBJECT-TYPE
SYNTAX LispEidRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispEidRegistrationTable."
INDEX { lispEidRegistrationEidLength,
lispEidRegistrationEid }
::= { lispEidRegistrationTable 1 }
LispEidRegistrationEntry ::= SEQUENCE {
lispEidRegistrationEidLength Integer32,
lispEidRegistrationEid LispAddressType,
lispEidRegistrationSiteName OCTET STRING,
lispEidRegistrationSiteDescription OCTET STRING,
lispEidRegistrationIsRegistered TruthValue,
lispEidRegistrationFirstRegisterTime TimeTicks,
lispEidRegistrationLastRegisterTime TimeTicks,
lispEidRegistrationLastRegisterSenderLength Integer32,
lispEidRegistrationLastRegisterSender LispAddressType,
lispEidRegistrationRouteTag Unsigned32,
lispEidRegistrationAuthenticationErrors Counter64,
lispEidRegistrationRlocsMismatch Counter64
}
lispEidRegistrationEidLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispEidRegistrationEid, the next object."
::= { lispEidRegistrationEntry 1 }
Schudel, et al. Expires December 30, 2012 [Page 33]
Internet-Draft LISP MIB June 2012
lispEidRegistrationEid OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The EID prefix that is being registered."
::= { lispEidRegistrationEntry 2 }
lispEidRegistrationSiteName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..63))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Site name used by a Map-Server to distinguish
different LISP sites that are registering with it."
::= { lispEidRegistrationEntry 3 }
lispEidRegistrationSiteDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Description for a site name used by a Map-Server.
The EID prefix that is being registered belongs to
this site."
::= { lispEidRegistrationEntry 4 }
lispEidRegistrationIsRegistered OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the registration status of the given
EID prefix. If this object is TRUE, then it
means the EID prefix is registered."
::= { lispEidRegistrationEntry 5 }
lispEidRegistrationFirstRegisterTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since a first valid register message for
the given EID prefix was received by this device."
::= { lispEidRegistrationEntry 6 }
lispEidRegistrationLastRegisterTime OBJECT-TYPE
Schudel, et al. Expires December 30, 2012 [Page 34]
Internet-Draft LISP MIB June 2012
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last valid register message for
the given EID prefix was received by this device."
::= { lispEidRegistrationEntry 7 }
lispEidRegistrationLastRegisterSenderLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispEidRegistrationLastRegisterSender, the next object."
::= { lispEidRegistrationEntry 8 }
lispEidRegistrationLastRegisterSender OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Source address of the last valid register message
for the given EID prefix that was received by
this device."
::= { lispEidRegistrationEntry 9 }
lispEidRegistrationRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Value of the routing table tag assigned to the
given EID prefix."
::= { lispEidRegistrationEntry 10 }
lispEidRegistrationAuthenticationErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of total authentication errors of
map-registers received for the given EID
prefix."
::= { lispEidRegistrationEntry 11 }
lispEidRegistrationRlocsMismatch OBJECT-TYPE
Schudel, et al. Expires December 30, 2012 [Page 35]
Internet-Draft LISP MIB June 2012
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of total map-registers received that had at
least one RLOC that was not in the allowed list of
RLOCs for the given EID prefix."
::= { lispEidRegistrationEntry 12 }
lispEidRegistrationEtrTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispEidRegistrationEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of ETRs that register
the given EID prefix with this device when configured to
be a Map-Server."
REFERENCE "[LISP]"
::= { lispObjects 10 }
lispEidRegistrationEtrEntry OBJECT-TYPE
SYNTAX LispEidRegistrationEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispEidRegistrationEtrTable."
INDEX { lispEidRegistrationEidLength,
lispEidRegistrationEid,
lispEidRegistrationEtrSenderLength,
lispEidRegistrationEtrSender }
::= { lispEidRegistrationEtrTable 1 }
LispEidRegistrationEtrEntry ::= SEQUENCE {
lispEidRegistrationEtrSenderLength Integer32,
lispEidRegistrationEtrSender LispAddressType,
lispEidRegistrationEtrLastRegisterTime TimeTicks,
lispEidRegistrationEtrTtl TimeTicks,
lispEidRegistrationEtrProxyReply TruthValue,
lispEidRegistrationEtrWantsMapNotify TruthValue
}
lispEidRegistrationEtrSenderLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Schudel, et al. Expires December 30, 2012 [Page 36]
Internet-Draft LISP MIB June 2012
"This object is used to get the octet-length of
lispEidRegistrationEtrSender, the next object."
::= { lispEidRegistrationEtrEntry 1 }
lispEidRegistrationEtrSender OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Source address of the ETR that is sending valid register
messages for this EID prefix to this device."
::= { lispEidRegistrationEtrEntry 2 }
lispEidRegistrationEtrLastRegisterTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last valid register message from this ETR
for the given EID prefix was received by this device."
::= { lispEidRegistrationEtrEntry 3 }
lispEidRegistrationEtrTtl OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time in minutes of the Record TTL of the
registering ETR device for this EID prefix."
::= { lispEidRegistrationEtrEntry 4 }
lispEidRegistrationEtrProxyReply OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates proxy-replying status of the registering
ETR for this EID prefix. If this object is TRUE, then
it means the Map-Server can proxy-reply."
::= { lispEidRegistrationEtrEntry 5 }
lispEidRegistrationEtrWantsMapNotify OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the EID prefix wants
Schudel, et al. Expires December 30, 2012 [Page 37]
Internet-Draft LISP MIB June 2012
Map-Notifications. If this object is TRUE, then
it means the EID prefix wants Map-Notifications."
::= { lispEidRegistrationEtrEntry 6 }
lispEidRegistrationLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispEidRegistrationLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of all locators
per LISP site that are served by this device when
configured to be a Map-Server."
REFERENCE "[LISP]"
::= { lispObjects 11 }
lispEidRegistrationLocatorEntry OBJECT-TYPE
SYNTAX LispEidRegistrationLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispEidRegistrationLocatorTable."
INDEX { lispEidRegistrationEidLength,
lispEidRegistrationEid,
lispEidRegistrationEtrSenderLength,
lispEidRegistrationEtrSender,
lispEidRegistrationLocatorRlocLength,
lispEidRegistrationLocatorRloc }
::= { lispEidRegistrationLocatorTable 1 }
LispEidRegistrationLocatorEntry ::= SEQUENCE {
lispEidRegistrationLocatorRlocLength Integer32,
lispEidRegistrationLocatorRloc LispAddressType,
lispEidRegistrationLocatorRlocState INTEGER,
lispEidRegistrationLocatorIsLocal TruthValue,
lispEidRegistrationLocatorPriority Integer32,
lispEidRegistrationLocatorWeight Integer32,
lispEidRegistrationLocatorMPriority Integer32,
lispEidRegistrationLocatorMWeight Integer32
}
lispEidRegistrationLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Schudel, et al. Expires December 30, 2012 [Page 38]
Internet-Draft LISP MIB June 2012
"This object is used to get the octet-length of
lispEidRegistrationLocatorRloc, the next object."
::= { lispEidRegistrationLocatorEntry 1 }
lispEidRegistrationLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locator of the given EID prefix being registered
by the given ETR with this device."
::= { lispEidRegistrationLocatorEntry 2 }
lispEidRegistrationLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The cached state of this RLOC received in
map-register from the ETR by the device, in the
capacity of a Map-Server. Value 1 refers to up,
value 2 refers to down."
::= { lispEidRegistrationLocatorEntry 3 }
lispEidRegistrationLocatorIsLocal OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if the given locator is local to the
registering ETR. If this object is TRUE, then it
means the locator is local."
::= { lispEidRegistrationLocatorEntry 4 }
lispEidRegistrationLocatorPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the RLOC for this EID prefix
in the register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 5 }
lispEidRegistrationLocatorWeight OBJECT-TYPE
Schudel, et al. Expires December 30, 2012 [Page 39]
Internet-Draft LISP MIB June 2012
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the RLOC for this EID prefix
in the register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 6 }
lispEidRegistrationLocatorMPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the RLOC for this EID prefix
in the register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 7 }
lispEidRegistrationLocatorMWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the RLOC for this EID prefix
in the register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 8 }
lispUseMapServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispUseMapServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of the
map-server(s) with which this device is
configured to register."
REFERENCE "[LISP]"
::= { lispObjects 12 }
lispUseMapServerEntry OBJECT-TYPE
SYNTAX LispUseMapServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispUseMapServerTable."
INDEX { lispUseMapServerAddressLength,
lispUseMapServerAddress }
::= { lispUseMapServerTable 1 }
Schudel, et al. Expires December 30, 2012 [Page 40]
Internet-Draft LISP MIB June 2012
LispUseMapServerEntry ::= SEQUENCE {
lispUseMapServerAddressLength Integer32,
lispUseMapServerAddress LispAddressType,
lispUseMapServerState INTEGER
}
lispUseMapServerAddressLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispUseMapServerAddress, the next object."
::= { lispUseMapServerEntry 1 }
lispUseMapServerAddress OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of Map-Server configured on this device."
::= { lispUseMapServerEntry 2 }
lispUseMapServerState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of this Map-Server configured on this
device (1 = Map-Server is up; 2 = Map-Server
is down)."
::= { lispUseMapServerEntry 3 }
lispUseMapResolverTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispUseMapResolverEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of the
map-resolver(s) this device is configured to use."
REFERENCE "[LISP]"
::= { lispObjects 13 }
Schudel, et al. Expires December 30, 2012 [Page 41]
Internet-Draft LISP MIB June 2012
lispUseMapResolverEntry OBJECT-TYPE
SYNTAX LispUseMapResolverEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispUseMapResolverTable."
INDEX { lispUseMapResolverAddressLength,
lispUseMapResolverAddress }
::= { lispUseMapResolverTable 1 }
LispUseMapResolverEntry ::= SEQUENCE {
lispUseMapResolverAddressLength Integer32,
lispUseMapResolverAddress LispAddressType,
lispUseMapResolverState INTEGER
}
lispUseMapResolverAddressLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispUseMapResolverAddress, the next object."
::= { lispUseMapResolverEntry 1 }
lispUseMapResolverAddress OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of map-resolver configured on this device."
::= { lispUseMapResolverEntry 2 }
lispUseMapResolverState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of this Map-Resolver configured on this device
(1 = Map-Resolver is up; 2 = Map-Resolver is down)."
::= { lispUseMapResolverEntry 3 }
Schudel, et al. Expires December 30, 2012 [Page 42]
Internet-Draft LISP MIB June 2012
lispUseProxyEtrTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispUseProxyEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of all
Proxy ETRs that this device is configured
to use."
REFERENCE "[LISP]"
::= { lispObjects 14 }
lispUseProxyEtrEntry OBJECT-TYPE
SYNTAX LispUseProxyEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispUseProxyEtrTable."
INDEX { lispUseProxyEtrAddressLength,
lispUseProxyEtrAddress }
::= { lispUseProxyEtrTable 1 }
LispUseProxyEtrEntry ::= SEQUENCE {
lispUseProxyEtrAddressLength Integer32,
lispUseProxyEtrAddress LispAddressType,
lispUseProxyEtrPriority Integer32,
lispUseProxyEtrWeight Integer32,
lispUseProxyEtrMPriority Integer32,
lispUseProxyEtrMWeight Integer32,
lispUseProxyEtrState INTEGER
}
lispUseProxyEtrAddressLength OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispUseProxyEtrAddress, the next object."
::= { lispUseProxyEtrEntry 1 }
lispUseProxyEtrAddress OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of Proxy ETR configured on this device."
::= { lispUseProxyEtrEntry 2 }
Schudel, et al. Expires December 30, 2012 [Page 43]
Internet-Draft LISP MIB June 2012
lispUseProxyEtrPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the PETR locator."
::= { lispUseProxyEtrEntry 3 }
lispUseProxyEtrWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the PETR locator."
::= { lispUseProxyEtrEntry 4 }
lispUseProxyEtrMPriority OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the PETR locator."
::= { lispUseProxyEtrEntry 5 }
lispUseProxyEtrMWeight OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the PETR locator."
::= { lispUseProxyEtrEntry 6 }
lispUseProxyEtrState OBJECT-TYPE
SYNTAX INTEGER {
down (0),
up (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of this Proxy ETR configured on this device
(0 = Proxy ETR is down; 1 = Proxy ETR is up)."
::= { lispUseProxyEtrEntry 7 }
Schudel, et al. Expires December 30, 2012 [Page 44]
Internet-Draft LISP MIB June 2012
--
-- Conformance Information
--
lispCompliances OBJECT IDENTIFIER ::= { lispConformance 1 }
lispGroups OBJECT IDENTIFIER ::= { lispConformance 2 }
--
-- Compliance Statements
--
lispMIBComplianceEtr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP ETRs."
MODULE -- this module
MANDATORY-GROUPS { lispMIBEtrGroup }
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
Schudel, et al. Expires December 30, 2012 [Page 45]
Internet-Draft LISP MIB June 2012
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 1 }
lispMIBComplianceItr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP ITRs."
MODULE -- this module
MANDATORY-GROUPS { lispMIBItrGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Expires December 30, 2012 [Page 46]
Internet-Draft LISP MIB June 2012
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 2 }
lispMIBCompliancePetr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Proxy-ETRs."
MODULE -- this module
MANDATORY-GROUPS { lispMIBPetrGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Expires December 30, 2012 [Page 47]
Internet-Draft LISP MIB June 2012
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Expires December 30, 2012 [Page 48]
Internet-Draft LISP MIB June 2012
::= { lispCompliances 3 }
lispMIBCompliancePitr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Proxy-ITRs."
MODULE -- this module
MANDATORY-GROUPS { lispMIBPitrGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Expires December 30, 2012 [Page 49]
Internet-Draft LISP MIB June 2012
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 4 }
lispMIBComplianceMapServer MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Map Servers."
MODULE -- this module
MANDATORY-GROUPS { lispMIBMapServerGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Expires December 30, 2012 [Page 50]
Internet-Draft LISP MIB June 2012
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 5 }
lispMIBComplianceMapResolver MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Map Resolvers."
MODULE -- this module
MANDATORY-GROUPS { lispMIBMapResolverGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Expires December 30, 2012 [Page 51]
Internet-Draft LISP MIB June 2012
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 6 }
--
-- Units of Conformance
--
lispMIBEtrGroup OBJECT-GROUP
OBJECTS { lispFeaturesEtrEnabled,
lispMappingDatabaseLsb,
lispMappingDatabaseLocatorRlocPriority,
lispMappingDatabaseLocatorRlocWeight,
Schudel, et al. Expires December 30, 2012 [Page 52]
Internet-Draft LISP MIB June 2012
lispMappingDatabaseLocatorRlocMPriority,
lispMappingDatabaseLocatorRlocMWeight,
lispMappingDatabaseLocatorRlocState,
lispMappingDatabaseLocatorRlocLocal,
lispConfiguredLocatorRlocState,
lispConfiguredLocatorRlocLocal,
lispUseMapServerState
}
STATUS current
DESCRIPTION
"A collection of objects to support basic
management of LISP ETRs."
::= { lispGroups 1 }
lispMIBItrGroup OBJECT-GROUP
OBJECTS { lispFeaturesItrEnabled,
lispFeaturesMapCacheSize,
lispMappingDatabaseLsb,
lispMapCacheLocatorRlocPriority,
lispMapCacheLocatorRlocWeight,
lispMapCacheLocatorRlocMPriority,
lispMapCacheLocatorRlocMWeight,
lispMapCacheLocatorRlocState,
lispMapCacheEidUpTime,
lispMapCacheEidExpiryTime,
lispUseMapResolverState,
lispUseProxyEtrPriority,
lispUseProxyEtrWeight,
lispUseProxyEtrMPriority,
lispUseProxyEtrMWeight,
lispUseProxyEtrState
}
STATUS current
DESCRIPTION
"A collection of objects to support basic
management of LISP ITRs."
::= { lispGroups 2 }
lispMIBPetrGroup OBJECT-GROUP
OBJECTS { lispFeaturesProxyEtrEnabled
}
STATUS current
DESCRIPTION
"A collection of objects to support basic
management of LISP Proxy-ETRs."
::= { lispGroups 3 }
lispMIBPitrGroup OBJECT-GROUP
Schudel, et al. Expires December 30, 2012 [Page 53]
Internet-Draft LISP MIB June 2012
OBJECTS { lispFeaturesProxyItrEnabled,
lispConfiguredLocatorRlocState,
lispConfiguredLocatorRlocLocal
}
STATUS current
DESCRIPTION
"A collection of objects to support basic
management of LISP Proxy-ITRs."
::= { lispGroups 4 }
lispMIBMapServerGroup OBJECT-GROUP
OBJECTS { lispFeaturesMapServerEnabled,
lispEidRegistrationIsRegistered,
lispEidRegistrationLocatorRlocState
}
STATUS current
DESCRIPTION
"A collection of objects to support basic
management of LISP Map Servers."
::= { lispGroups 5 }
lispMIBMapResolverGroup OBJECT-GROUP
OBJECTS { lispFeaturesMapResolverEnabled
}
STATUS current
DESCRIPTION
"A collection of objects to support basic
management of LISP Map Resolvers."
::= { lispGroups 6 }
lispMIBEtrExtendedGroup OBJECT-GROUP
OBJECTS { lispFeaturesRlocProbeEnabled,
lispFeaturesEtrAcceptMapDataEnabled,
lispFeaturesEtrAcceptMapDataVerifyEnabled,
lispMappingDatabaseEidPartitioned
}
STATUS current
DESCRIPTION
"A collection of objects to support management
of LISP features and properties on ETRs."
::= { lispGroups 7 }
lispMIBItrExtendedGroup OBJECT-GROUP
OBJECTS { lispFeaturesRlocProbeEnabled,
lispMapCacheEidState,
lispMapCacheEidAuthoritative,
lispMapCacheLocatorRlocUpTime,
Schudel, et al. Expires December 30, 2012 [Page 54]
Internet-Draft LISP MIB June 2012
lispMapCacheLocatorRlocLastPriorityChange,
lispMapCacheLocatorRlocLastWeightChange,
lispMapCacheLocatorRlocLastMPriorityChange,
lispMapCacheLocatorRlocLastMWeightChange,
lispMapCacheLocatorRlocLastStateChange,
lispMapCacheLocatorRlocRtt
}
STATUS current
DESCRIPTION
"A collection of objects to support management
of LISP features and properties on ITRs."
::= { lispGroups 8 }
lispMIBMapServerExtendedGroup OBJECT-GROUP
OBJECTS { lispEidRegistrationSiteName,
lispEidRegistrationSiteDescription,
lispEidRegistrationIsRegistered,
lispEidRegistrationFirstRegisterTime,
lispEidRegistrationLastRegisterTime,
lispEidRegistrationLastRegisterSenderLength,
lispEidRegistrationLastRegisterSender,
lispEidRegistrationRouteTag,
lispEidRegistrationEtrLastRegisterTime,
lispEidRegistrationEtrTtl,
lispEidRegistrationEtrProxyReply,
lispEidRegistrationEtrWantsMapNotify,
lispEidRegistrationLocatorIsLocal,
lispEidRegistrationLocatorPriority,
lispEidRegistrationLocatorWeight,
lispEidRegistrationLocatorMPriority,
lispEidRegistrationLocatorMWeight
}
STATUS current
DESCRIPTION
"A collection of objects to support management
of LISP features and properties on Map Servers."
::= { lispGroups 9 }
lispMIBTuningParametersGroup OBJECT-GROUP
OBJECTS { lispFeaturesMapCacheLimit,
lispFeaturesEtrMapCacheTtl
}
STATUS current
DESCRIPTION
"A collection of writeable objects used to
configure LISP behavior and to tune performance."
::= { lispGroups 10 }
Schudel, et al. Expires December 30, 2012 [Page 55]
Internet-Draft LISP MIB June 2012
lispMIBEncapStatisticsGroup OBJECT-GROUP
OBJECTS { lispMappingDatabaseEncapOctets,
lispMappingDatabaseEncapPackets,
lispMappingDatabaseLocatorRlocEncapOctets,
lispMappingDatabaseLocatorRlocEncapPackets,
lispMapCacheEncapOctets,
lispMapCacheEncapPackets,
lispMapCacheLocatorRlocEncapOctets,
lispMapCacheLocatorRlocEncapPackets,
lispConfiguredLocatorRlocEncapOctets,
lispConfiguredLocatorRlocEncapPackets
}
STATUS current
DESCRIPTION
"A collection of LISP encapsulation statistics
by the device."
::= { lispGroups 11 }
lispMIBDecapStatisticsGroup OBJECT-GROUP
OBJECTS { lispMappingDatabaseDecapOctets,
lispMappingDatabaseDecapPackets,
lispMappingDatabaseLocatorRlocDecapOctets,
lispMappingDatabaseLocatorRlocDecapPackets,
lispMapCacheDecapOctets,
lispMapCacheDecapPackets,
lispMapCacheLocatorRlocDecapOctets,
lispMapCacheLocatorRlocDecapPackets,
lispConfiguredLocatorRlocDecapOctets,
lispConfiguredLocatorRlocDecapPackets
}
STATUS current
DESCRIPTION
"A collection of LISP decapsulation statistics
by the device."
::= { lispGroups 12 }
lispMIBDiagnosticsGroup OBJECT-GROUP
OBJECTS { lispGlobalStatsMapRequestsIn,
lispGlobalStatsMapRequestsOut,
lispGlobalStatsMapRepliesIn,
lispGlobalStatsMapRepliesOut,
lispGlobalStatsMapRegistersIn,
lispGlobalStatsMapRegistersOut,
lispEidRegistrationAuthenticationErrors,
lispEidRegistrationRlocsMismatch
}
STATUS current
DESCRIPTION
Schudel, et al. Expires December 30, 2012 [Page 56]
Internet-Draft LISP MIB June 2012
"Objects providing additional diagnostics related
to a LISP router."
::= { lispGroups 13 }
lispMIBVrfGroup OBJECT-GROUP
OBJECTS { lispIidToVrfVpnId
}
STATUS current
DESCRIPTION
"Objects providing information related to VRF
configurations on a LISP router."
::= { lispGroups 14 }
END
8. Relationship to Other MIB Modules
8.1. MIB modules required for IMPORTS
The LISP MIB imports the textual-convention AddressFamilyNumbers from
the IANA-ADDRESS-FAMILY-NUMBERS-MIB [IANA].
9. Security Considerations
There are no management objects defined in this MIB module that have
a MAX-ACCESS clause of read-write and/or read-create. As long as
these MIB modules are implemented correctly, there are no risks that
any management objects of this MIB module can modify device settings
via direct SNMP SET operations.
There are no readable objects in this MIB module (i.e., objects with
a MAX-ACCESS other than not-accessible) that are considered
sensitive.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
there is no control as to who on the secure network is allowed to
access and GET/SET (read/change/create/delete) the objects in this
MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
Schudel, et al. Expires December 30, 2012 [Page 57]
Internet-Draft LISP MIB June 2012
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of these MIB modules is properly configured to give access
to the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
10. IANA Considerations
LISP is an experimental protocol and the LISP MIB is an experimental
MIB. No IANA actions are required by this document.
11. References
11.1. Normative References
[IANA] "IANA-ADDRESS-FAMILY-NUMBERS-MIB DEFINITIONS", <http://
www.iana.org/assignments/ianaaddressfamilynumbers-mib>.
[INTERWORK] Lewis, D., Meyer, D., Farinacci, D., and V. Fuller,
"Interworking LISP with IPv4 and IPv6",
draft-ietf-lisp-interworking-06.txt (work in progress),
March 2012.
[LISP] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis,
"Locator/ID Separation Protocol (LISP)",
draft-ietf-lisp-23.txt (work in progress), May 2012.
[LISP-MS] Farinacci, D. and V. Fuller, "LISP Map Server",
draft-ietf-lisp-ms-16.txt (work in progress),
March 2012.
[RFC1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035, November 1987.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2404] Madson, C. and R. Glenn, "The Use of HMAC-SHA-1-96
within ESP and AH", RFC 2404, November 1998.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578,
April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
Schudel, et al. Expires December 30, 2012 [Page 58]
Internet-Draft LISP MIB June 2012
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC4634] Eastlake, D. and T. Hansen, "US Secure Hash Algorithms
(SHA and HMAC-SHA)", RFC 4634, July 2006.
11.2. Informative References
[LCAF] Farinacci, D., Meyer, D., and J. Snijders, "LISP
Canonical Address Format",
draft-farinacci-lisp-lcaf-07.txt (work in progress),
March 2012.
[LISP-MCAST] Farinacci, D., Meyer, D., Zwiebel, J., and S. Venaas,
"LISP for Multicast Environments",
draft-ietf-lisp-multicast-14.txt (work in progress),
February 2012.
[LISP-MN] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis,
"LISP Mobile Node Architecture",
draft-meyer-lisp-mn-07.txt (work in progress),
April 2012.
[RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
Traina, "Generic Routing Encapsulation (GRE)",
RFC 2784, March 2000.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
Protocol 4 (BGP-4)", RFC 4271, January 2006.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
January 2007.
Appendix A. Open Issues
Open issues for the LISP MIB include the following:
1. This LISP MIB draft does not include LISP Multicast
considerations. Multicast considerations will be added in a
separate LISP Multicast MIB draft.
Schudel, et al. Expires December 30, 2012 [Page 59]
Internet-Draft LISP MIB June 2012
Appendix B. Acknowledgments
A thank you is owed to Dino Farinacci for his inputs and review
comments on the initial versions of this draft. In addition, the
authors would like to gratefully acknowledge several others who have
reviewed and commented on this draft. They include: Darrel Lewis,
Isidor Kouvelas, Jesper Skriver, Selina Heimlich, and Parna Agrawal.
Authors' Addresses
Gregg Schudel
cisco Systems
Tasman Drive
San Jose, CA 95134
USA
EMail: gschudel@cisco.com
Amit Jain
cisco Systems
Tasman Drive
San Jose, CA 95134
USA
EMail: amijain@cisco.com
Victor Moreno
cisco Systems
Tasman Drive
San Jose, CA 95134
USA
EMail: vimoreno@cisco.com
Schudel, et al. Expires December 30, 2012 [Page 60]