Skip to main content

Advertising Layer 2 Bundle Member Link Attributes in OSPF
draft-ietf-lsr-ospf-l2bundles-09

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 9356.
Authors Ketan Talaulikar , Peter Psenak
Last updated 2022-10-06
Replaces draft-ketant-lsr-ospf-l2bundles
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Submitted to IESG for Publication
Document shepherd Acee Lindem
Shepherd write-up Show Last changed 2022-05-29
IESG IESG state Became RFC 9356 (Proposed Standard)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD John Scudder
Send notices to chopps@chopps.org, acee@cisco.com
IANA IANA review state IANA OK - Actions Needed
draft-ietf-lsr-ospf-l2bundles-09
Link State Routing                                    K. Talaulikar, Ed.
Internet-Draft                                                 P. Psenak
Updates: 9085 (if approved)                                Cisco Systems
Intended status: Standards Track                          6 October 2022
Expires: 9 April 2023

       Advertising Layer 2 Bundle Member Link Attributes in OSPF
                    draft-ietf-lsr-ospf-l2bundles-09

Abstract

   There are deployments where the Layer 3 (L3) interface on which OSPF
   operates is a Layer 2 (L2) interface bundle.  Existing OSPF
   advertisements only support advertising link attributes of the Layer
   3 interface.  If entities external to OSPF wish to control traffic
   flows on the individual physical links which comprise the Layer 2
   interface bundle, link attribute information for the bundle members
   is required.

   This document defines the protocol extensions for OSPF to advertise
   the link attributes of L2 bundle members.  The document also
   specifies the advertisment of these OSPF extensions via BGP Link
   State protocol and thereby updates RFC9085.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 9 April 2023.

Copyright Notice

   Copyright (c) 2022 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

Talaulikar & Psenak       Expires 9 April 2023                  [Page 1]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  L2 Bundle Member Attributes . . . . . . . . . . . . . . . . .   4
   3.  BGP-LS Advertisement  . . . . . . . . . . . . . . . . . . . .   7
   4.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   7
   5.  Operational Considerations  . . . . . . . . . . . . . . . . .   7
   6.  Security Considerations . . . . . . . . . . . . . . . . . . .   8
   7.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .   8
   8.  References  . . . . . . . . . . . . . . . . . . . . . . . . .   8
     8.1.  Normative References  . . . . . . . . . . . . . . . . . .   8
     8.2.  Informational References  . . . . . . . . . . . . . . . .   9
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  11

1.  Introduction

   There are deployments where the Layer 3 interface on which an OSPF
   adjacency is established is a Layer 2 interface bundle, for instance
   a Link Aggregation Group (LAG) [IEEE802.1AX].  This reduces the
   number of adjacencies that need to be maintained by the OSPF protocol
   in cases where there are parallel links between the neighbors.
   Entities external to OSPF such as Path Computation Elements (PCE)
   [RFC4655] may wish to control traffic flows on individual Layer 2
   member links of the underlying bundle (e.g., LAG) interface.  To do
   so, link attribute information for individual bundle members is
   required.  The protocol extensions defined in this document provide
   the means to advertise this information.

   This document defines sub-TLVs to advertise link attribute
   information for each of the L2 bundle members which comprise the
   Layer 3 interface on which OSPF operates.  Similar capabilities were
   introduced in IS-IS via [RFC8668].

Talaulikar & Psenak       Expires 9 April 2023                  [Page 2]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   [RFC8665] and [RFC8666] introduced the adjacency segment identifier
   (Adj-SID) link attribute for OSPFv2 and OSPFv3 respectively which can
   be used as an instruction to forwarding to send traffic over a
   specific link [RFC8402].  This document enables the advertisement of
   the Adj-SIDs using the same Adjacency SID Sub-TLV at the granularity
   level of each L2 bundle member link so that traffic may be steered
   over that specific member link.

   Note that the advertisements at the L2 bundle member link-level
   defined in this document are intended to be provided to external (to
   OSPF) entities and do not alter or change the OSPF route computation.
   The following items are intentionally not defined and are outside the
   scope of this document:

   *  What link attributes will be advertised.  This is determined by
      the needs of the external entities.

   *  A minimum or default set of link attributes.

   *  How these attributes are configured.

   *  How the advertisements are used.

   *  What impact the use of these advertisements may have on traffic
      flow in the network.

   *  How the advertisements are passed to external entities.

   The BGP Link State (BGP-LS) [RFC7752] was extended for the
   advertisement of Layer 2 bundle members and their attributes by
   [RFC9085] which covered only IS-IS.  This document updates [RFC9085]
   by specifying the advertisement from OSPF (refer Section 3).

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

Talaulikar & Psenak       Expires 9 April 2023                  [Page 3]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

2.  L2 Bundle Member Attributes

   A new L2 Bundle Member Attributes Sub-TLV is introduced to advertise
   L2 bundle member attributes in both OSPFv2 and OSPFv3.  In the case
   of OSPFv2, this sub-TLV is an optional sub-TLV of the OSPFv2 Extended
   Link TLV that is used to describe link attributes via the OSPFv2
   Extended Link Opaque LSA [RFC7684].  In the case of OSPFv3, this sub-
   TLV is an optional sub-TLV of the Router Link TLV of the OSPFv3 E-
   Router-LSA [RFC8362].

   When the OSPF adjacency is associated with an L2 bundle interface,
   this sub-TLV is used to advertise the underlying L2 bundle member
   links along with their respective link attributes.  The inclusion of
   this information implies that the identified link is a member of the
   L2 bundle associated with an OSPF L3 link and that the member link is
   operationally up.  Therefore, advertisements of member links MUST NOT
   be done when the member link becomes operationally down or it is no
   longer a member of the identified L2 bundle.

   The advertisement of the L2 Bundle Member Attributes Sub-TLV may be
   asymmetric for an OSPF link depending on the underlying layer 2
   connectivity i.e., advertised by the router on only one end.

   The L2 Bundle Member Attributes Sub-TLV has the following format:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |               Type            |          Length               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                   L2 Bundle Member Descriptor                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |           Member Link Attribute sub-TLVs (variable)          //
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

            Figure 1: L2 Bundle Member Attributes sub-TLV Format

   Where:

      Type: 24 for OSPFv2 and 29 for OSPFv3

      Length: The total length (in octets) of the value portion of the
      TLV including nested Sub-TLVs.

      L2 Bundle Member Descriptor: A 4 octet Link Local Identifier as
      described in [RFC4202] and used in [RFC8510] for the member link.

Talaulikar & Psenak       Expires 9 April 2023                  [Page 4]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   Link attributes for L2 bundle member links are advertised as sub-TLVs
   of the L2 Bundle Member Attribute Sub-TLV.

   In the case of OSPFv2, the L2 Bundle Member Attributes Sub-TLV shares
   the sub-TLV space of the Extended Link TLV and the sub-TLVs of the
   Extended Link TLV MAY be used to describe the attributes of the
   member link.  Figure 2 below lists sub-TLVs and their applicability
   for L2 bundle member links.  The sub-TLVs that are not applicable
   MUST NOT be used as sub-TLVs for the L2 Bundle Member Attributes Sub-
   TLV.  Specifications that introduce new sub-TLVs of the Extended Link
   TLV MUST indicate their applicability for the L2 Bundle Member
   Attributes Sub-TLV.  Typically, attributes that have Layer 3
   semantics would not be applicable while Layer 2 attributes would
   apply.  An implementation MUST ignore any sub-TLVs received that are
   not applicable in the context of the L2 Bundle Member Attribute Sub-
   TLV.

     Y - applicable
     N - not-applicable

      1  SID/Label (N)
      2  Adj-SID (Y)
      3  LAN Adj-SID/Label (Y)
      4  Network-to-Router Metric (N)
      5  RTM Capability (N)
      6  OSPFv2 Link MSD (N)
      7  Graceful-Link-Shutdown (N)
      8  Remote IPv4 Address (N)
      9  Local/Remote Interface ID (N)
     10  Application Specific Link Attributes (Y)
     11  Shared Risk Link Group (Y)
     12  Unidirectional Link Delay (Y)
     13  Min/Max Unidirectional Link Delay (Y)
     14  Unidirectional Delay Variation (Y)
     15  Unidirectional Link Loss (Y)
     16  Unidirectional Residual Bandwidth (Y)
     17  Unidirectional Available Bandwidth (Y)
     18  Unidirectional Utilized Bandwidth (Y)
     19  Administrative Group (Y)
     20  Extended Administrative Group (Y)
     21  OSPFv2 Link Attributes Bits (N)
     22  TE Metric (Y)
     23  Maximum Link Bandwidth (Y)
     24  L2 Bundle Member Attributes (N)

      Figure 2: Applicability of OSPFv2 Link Attribute Sub-TLVs for L2
                               Bundle Members

Talaulikar & Psenak       Expires 9 April 2023                  [Page 5]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   In the case of OSPFv3, the L2 Bundle Member Attributes Sub-TLV shares
   the sub-TLV space of the Router Link TLV and the sub-TLVs of the
   Router Link TLV MAY be used to describe the attributes of the member
   link.  Figure 3 below lists sub-TLVs that are applicable to the
   Router Link TLV and their applicability for L2 bundle member links.
   The sub-TLVs that are not applicable MUST NOT be used as sub-TLVs for
   the L2 Bundle Member Attributes Sub-TLV.  Specifications that
   introduce new sub-TLVs of the Router Link TLV MUST indicate their
   applicability for the L2 Bundle Member Attributes Sub-TLV.  An
   implementation MUST ignore any sub-TLVs received that are not
   applicable in the context of the L2 Bundle Member Attribute Sub-TLV.

      Y - applicable
      N - not-applicable
      X - not Router Link Sub-TLV

      1  IPv6-Forwarding-Address (X)
      2  IPv4-Forwarding-Address (X)
      3  Route-Tag (X)
      4  Prefix SID (X)
      5  Adj-SID (Y)
      6  LAN Adj-SID (Y)
      7  SID/Label (N)
      8  Graceful-Link-Shutdown (N)
      9  OSPFv3 Link MSD (N)
     10  OSPFv3 Link Attribute Bits (N)
     11  Application Specific Link Attributes (Y)
     12  Shared Risk Link Group (Y)
     13  Unidirectional Link Delay (Y)
     14  Min/Max Unidirectional Link Delay (Y)
     15  Unidirectional Delay Variation (Y)
     16  Unidirectional Link Loss (Y)
     17  Unidirectional Residual Bandwidth (Y)
     18  Unidirectional Available Bandwidth (Y)
     19  Unidirectional Utilized Bandwidth (Y)
     20  Administrative Group (Y)
     21  Extended Administrative Group (Y)
     22  Traffic Engineering Metric (Y)
     23  Maximum Link Bandwidth (Y)
     24  Local Interface IPv6 Address (N)
     25  Remote Interface IPv6 Address (N)
     26  Flex-Algorithm Prefix Metric (X)
     27  Prefix Source OSPF Router-ID (X)
     28  Prefix Source Router Address (X)
     29  L2 Bundle Member Attributes (N)
     30  SRv6 SID Structure (Y)
     31  SRv6 End.X SID Structure (Y)
     32  SRv6 End.X SID Structure (Y)

Talaulikar & Psenak       Expires 9 April 2023                  [Page 6]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

      Figure 3: Applicability of OSPFv3 Link Attribute Sub-TLVs for L2
                               Bundle Members

3.  BGP-LS Advertisement

   The BGP-LS extensions for the advertisment of Layer 2 bundle members
   and their attributes was specified in [RFC9085].  Using the OSPF L2
   Bundle Member Attributes sub-TLV defined in this document, the L2
   bundle member information can now be advertised from OSPF into BGP-LS
   on the same lines as discussed for IS-IS in section 2.2.3 of
   [RFC9085].

4.  IANA Considerations

   IANA has allocated the following code point via early allocation in
   the "OSPFv2 Extended Link TLV Sub-TLVs" registry under the "OSPFv2
   Parameters" registry that needs to be made permanent:

   Value: 24

   Name: L2 Bundle Member Attributes

   IANA has allocated the following code point via early allocation in
   the "OSPFv3 Extended LSA Sub-TLVs" registry under the "OSPFv3
   Parameters" registry that needs to be made permanent:

   Value: 29

   Name: L2 Bundle Member Attributes

   IANA is requested to introduce a column "Applicability to L2 Bundle
   Member TLV" in the registry tables for the "OSPFv2 Extended Link TLV
   Sub-TLVs" registry with the initial updates (Y/N) against allocations
   as indicated in Figure 2.  Similarly, IANA is requested to introduce
   a column "Applicability to L2 Bundle Member TLV" in the registry
   tables for the "OSPFv3 Extended LSA Sub-TLVs" registry with the
   initial updates (Y/N/X) against allocations as indicated in Figure 3.
   Further allocations from these two registries are expected to
   indicate the applicability of the introduced sub-TLV to the L2 Bundle
   Member TLV that would get updated in these registries.

5.  Operational Considerations

   Implementations MUST NOT enable the advertisement of Layer 2 bundle
   member links and their attributes in OSPF LSAs by default and MUST
   provide a configuration option to enable their advertisement on
   specific links.

Talaulikar & Psenak       Expires 9 April 2023                  [Page 7]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   [I-D.ietf-ospf-yang] specifies the base OSPF YANG model.  The
   required configuration and operational elements for this feature are
   expected to be introduce as augmentation to this base OSPF YANG
   model.

6.  Security Considerations

   The OSPF protocol has supported the advertisement of link attribute
   information, including link identifiers, for many years.  The
   advertisements defined in this document are identical to existing
   advertisements defined in [RFC3630], [RFC4203], [RFC5329], [RFC7471],
   [RFC8665], and [RFC8666] - but are associated with L2 links which are
   part of a bundle interface on which the OSPF protocol operates.
   Therefore, the security considerations of these documents are
   applicable and there are no new security issues introduced by the
   extensions in this document.

   As always, if the protocol is used in an environment where
   unauthorized access to the physical links on which OSPF packets are
   sent occurs then attacks are possible.  The use of authentication as
   defined in [RFC5709], [RFC7474], [RFC4552], and [RFC7166] is
   recommended for preventing such attacks.

7.  Acknowledgements

   This document leverages the similar work done for IS-IS and the
   authors of this document would like to acknowledge the contributions
   of the authors of [RFC8668].

   The authors would like to thank Anoop Ghanwani, Paul Kyzivat, Dan
   Romascanu, and Russ Mundy for their review and feedback on this
   document.  The authors would also like to thank Acee Lindem for his
   detailed shepherd review of this document.  The authors would also
   like to thank John Scudder for his AD review and the discussion
   related to the applicability of TLVs/sub-TLVs to the L2 Bundle Member
   TLV.

8.  References

8.1.  Normative References

   [IEEE802.1AX]
              IEEE, "IEEE Standard for Local and Metropolitan Area
              Networks - Link Aggregation IEEE Std 802.1AX-2020
              (Revision of IEEE Std 802.1AX-2014)", 30 January 2020.

Talaulikar & Psenak       Expires 9 April 2023                  [Page 8]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC4202]  Kompella, K., Ed. and Y. Rekhter, Ed., "Routing Extensions
              in Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 4202, DOI 10.17487/RFC4202, October 2005,
              <https://www.rfc-editor.org/info/rfc4202>.

   [RFC7684]  Psenak, P., Gredler, H., Shakir, R., Henderickx, W.,
              Tantsura, J., and A. Lindem, "OSPFv2 Prefix/Link Attribute
              Advertisement", RFC 7684, DOI 10.17487/RFC7684, November
              2015, <https://www.rfc-editor.org/info/rfc7684>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8362]  Lindem, A., Roy, A., Goethals, D., Reddy Vallem, V., and
              F. Baker, "OSPFv3 Link State Advertisement (LSA)
              Extensibility", RFC 8362, DOI 10.17487/RFC8362, April
              2018, <https://www.rfc-editor.org/info/rfc8362>.

   [RFC8665]  Psenak, P., Ed., Previdi, S., Ed., Filsfils, C., Gredler,
              H., Shakir, R., Henderickx, W., and J. Tantsura, "OSPF
              Extensions for Segment Routing", RFC 8665,
              DOI 10.17487/RFC8665, December 2019,
              <https://www.rfc-editor.org/info/rfc8665>.

   [RFC8666]  Psenak, P., Ed. and S. Previdi, Ed., "OSPFv3 Extensions
              for Segment Routing", RFC 8666, DOI 10.17487/RFC8666,
              December 2019, <https://www.rfc-editor.org/info/rfc8666>.

   [RFC9085]  Previdi, S., Talaulikar, K., Ed., Filsfils, C., Gredler,
              H., and M. Chen, "Border Gateway Protocol - Link State
              (BGP-LS) Extensions for Segment Routing", RFC 9085,
              DOI 10.17487/RFC9085, August 2021,
              <https://www.rfc-editor.org/info/rfc9085>.

8.2.  Informational References

   [I-D.ietf-ospf-yang]
              Yeung, D., Qu, Y., Zhang, J., Chen, I., and A. Lindem,
              "YANG Data Model for OSPF Protocol", Work in Progress,
              Internet-Draft, draft-ietf-ospf-yang-29, 17 October 2019,
              <https://www.ietf.org/archive/id/draft-ietf-ospf-yang-
              29.txt>.

Talaulikar & Psenak       Expires 9 April 2023                  [Page 9]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   [RFC3630]  Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering
              (TE) Extensions to OSPF Version 2", RFC 3630,
              DOI 10.17487/RFC3630, September 2003,
              <https://www.rfc-editor.org/info/rfc3630>.

   [RFC4203]  Kompella, K., Ed. and Y. Rekhter, Ed., "OSPF Extensions in
              Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 4203, DOI 10.17487/RFC4203, October 2005,
              <https://www.rfc-editor.org/info/rfc4203>.

   [RFC4552]  Gupta, M. and N. Melam, "Authentication/Confidentiality
              for OSPFv3", RFC 4552, DOI 10.17487/RFC4552, June 2006,
              <https://www.rfc-editor.org/info/rfc4552>.

   [RFC4655]  Farrel, A., Vasseur, J.-P., and J. Ash, "A Path
              Computation Element (PCE)-Based Architecture", RFC 4655,
              DOI 10.17487/RFC4655, August 2006,
              <https://www.rfc-editor.org/info/rfc4655>.

   [RFC5329]  Ishiguro, K., Manral, V., Davey, A., and A. Lindem, Ed.,
              "Traffic Engineering Extensions to OSPF Version 3",
              RFC 5329, DOI 10.17487/RFC5329, September 2008,
              <https://www.rfc-editor.org/info/rfc5329>.

   [RFC5709]  Bhatia, M., Manral, V., Fanto, M., White, R., Barnes, M.,
              Li, T., and R. Atkinson, "OSPFv2 HMAC-SHA Cryptographic
              Authentication", RFC 5709, DOI 10.17487/RFC5709, October
              2009, <https://www.rfc-editor.org/info/rfc5709>.

   [RFC7166]  Bhatia, M., Manral, V., and A. Lindem, "Supporting
              Authentication Trailer for OSPFv3", RFC 7166,
              DOI 10.17487/RFC7166, March 2014,
              <https://www.rfc-editor.org/info/rfc7166>.

   [RFC7471]  Giacalone, S., Ward, D., Drake, J., Atlas, A., and S.
              Previdi, "OSPF Traffic Engineering (TE) Metric
              Extensions", RFC 7471, DOI 10.17487/RFC7471, March 2015,
              <https://www.rfc-editor.org/info/rfc7471>.

   [RFC7474]  Bhatia, M., Hartman, S., Zhang, D., and A. Lindem, Ed.,
              "Security Extension for OSPFv2 When Using Manual Key
              Management", RFC 7474, DOI 10.17487/RFC7474, April 2015,
              <https://www.rfc-editor.org/info/rfc7474>.

Talaulikar & Psenak       Expires 9 April 2023                 [Page 10]
Internet-Draft    OSPF L2 Bundle Member Link Attributes     October 2022

   [RFC7752]  Gredler, H., Ed., Medved, J., Previdi, S., Farrel, A., and
              S. Ray, "North-Bound Distribution of Link-State and
              Traffic Engineering (TE) Information Using BGP", RFC 7752,
              DOI 10.17487/RFC7752, March 2016,
              <https://www.rfc-editor.org/info/rfc7752>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

   [RFC8510]  Psenak, P., Ed., Talaulikar, K., Henderickx, W., and P.
              Pillay-Esnault, "OSPF Link-Local Signaling (LLS)
              Extensions for Local Interface ID Advertisement",
              RFC 8510, DOI 10.17487/RFC8510, January 2019,
              <https://www.rfc-editor.org/info/rfc8510>.

   [RFC8668]  Ginsberg, L., Ed., Bashandy, A., Filsfils, C., Nanduri,
              M., and E. Aries, "Advertising Layer 2 Bundle Member Link
              Attributes in IS-IS", RFC 8668, DOI 10.17487/RFC8668,
              December 2019, <https://www.rfc-editor.org/info/rfc8668>.

Authors' Addresses

   Ketan Talaulikar (editor)
   Cisco Systems
   India
   Email: ketant.ietf@gmail.com

   Peter Psenak
   Cisco Systems
   Apollo Business Center
   Mlynske nivy 43
   821 09 Bratislava
   Slovakia
   Email: ppsenak@cisco.com

Talaulikar & Psenak       Expires 9 April 2023                 [Page 11]