Link Identifier Extension to DLEP
draft-ietf-manet-dlep-lid-extension-01
The information below is for an old version of the document.
| Document | Type | Active Internet-Draft (manet WG) | |
|---|---|---|---|
| Authors | Rick Taylor , Stan Ratliff | ||
| Last updated | 2018-01-30 | ||
| Replaces | draft-dlep-lid | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text xml htmlized pdfized bibtex | ||
| Reviews |
SECDIR Last Call review
(of
-05)
Has Issues
GENART Last Call review
(of
-05)
Ready with Nits
|
||
| Stream | WG state | WG Document | |
| Document shepherd | (None) | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-manet-dlep-lid-extension-01
Mobile Ad hoc Networks Working Group R. Taylor
Internet-Draft Airbus Defence & Space
Intended status: Standards Track S. Ratliff
Expires: August 3, 2018 VT iDirect
January 30, 2018
Link Identifier Extension to DLEP
draft-ietf-manet-dlep-lid-extension-01
Abstract
There exists a class of modems that wish to support the Dynamic Link
Exchange Protocol (DLEP) [RFC8175] but do not present a single Layer
2 network domain as required by DLEP. Such devices may be:
o Modems that maintain a varying link to some upstream backbone
network infrastructure, where the ability to announce link state
and DLEP metrics is desired, but the concept of a DLEP destination
router for the backbone does not apply. Examples of such devices
can include LTE modems, IEEE 802.11 stations not in ad-hoc mode,
and some satellite terminals.
o Modems that provide Layer 3 wide area network connectivity between
devices, where individual DLEP destinations do exist, but are not
directly reachable by MAC address.
This document introduces an optional extension to the core DLEP
specification, allowing DLEP to be used between routers and modems
that operate in this way.
Note:
o This document is intended as an extension to the core DLEP
specification, and readers are expected to be fully conversant
with the operation of core DLEP.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Taylor & Ratliff Expires August 3, 2018 [Page 1]
Internet-Draft Link Identifier Extension to DLEP January 2018
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 3, 2018.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Requirements . . . . . . . . . . . . . . . . . . . . . . 3
2. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Identifier Restrictions . . . . . . . . . . . . . . . . . 4
2.2. Negotiation . . . . . . . . . . . . . . . . . . . . . . . 4
3. New Data Items . . . . . . . . . . . . . . . . . . . . . . . 5
3.1. Link Identifier Length Data Item . . . . . . . . . . . . 5
3.2. Link Identifier Data Item . . . . . . . . . . . . . . . . 6
4. Security Considerations . . . . . . . . . . . . . . . . . . . 6
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
5.1. DLEP Link Identifier Flag . . . . . . . . . . . . . . . . 7
6. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1. Normative References . . . . . . . . . . . . . . . . . . 7
6.2. Informative References . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
The Dynamic Link Exchange Protocol (DLEP) [RFC8175] describes a
protocol for modems to advertise the status of wireless links between
reachable destinations to attached routers. The core specification
of the protocol assumes that every modem in the radio network has an
attached DLEP router, and requires that the MAC address of the DLEP
interface on the attached router is used to identify the destination
Taylor & Ratliff Expires August 3, 2018 [Page 2]
Internet-Draft Link Identifier Extension to DLEP January 2018
in the network for purposes of reporting the state and quality of the
link to that destination.
This document describes a DLEP Extension allowing modems that do not
meet the strict requirement that DLEP must be implemented on a single
Layer 2 domain to use DLEP to describe link availability and quality
to one or more destinations reachable beyond a local or remote device
on the Layer 2 domain. A router can use this knowledge to influence
any routing or flow-control decisions regarding traffic to this
destination, understanding that such traffic flows via Layer 3.
A Layer 3 destination may be an attached DLEP router, in the case of
a modem that provides Layer 3 wide area network connectivity between
devices, or a logical destination that describes a set of attached
subnets, when referring to some upstream backbone network
infrastructure.
1.1. Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119.
2. Operation
To refer to a Layer 3 DLEP Destination, the DLEP session participant
adds a Link Identifier Data Item (Section 3.2) to the relevant
Destination Message, and (as usual) includes a MAC Address Data Item.
When paired with a Link Identifier Data Item, the MAC Address Data
Item MUST contain the MAC address of the last reachable node in the
Layer 2 domain beyond which the Layer 3 DLEP Destination resides.
For example, if the over-the-air network is not a single Layer 2
domain, the MAC Address Data Item might be the address of the LAN-
side interface of the local modem. Alternatively, when used with
some kind of backbone infrastructure, the MAC Address Data Item would
be the address of the last device reachable on the local Layer 2
domain. However, how such remote destinations are discovered is
beyond the scope of this specification.
As only modems are initially aware of Layer 3 DLEP Destinations, Link
Identifier Data Items referring to a new link MUST first appear in a
DLEP Destination Up Message from the modem to the router. Once a
link has been identified in this way, Link Identifier Data Items MAY
be used by either DLEP participant during the lifetime of a DLEP
session. Because of this, a router MUST NOT send a DLEP Destination
Announce Message containing a Link Identifier Data Item referring to
a link that has not been mentioned in a prior DLEP Destination Up
Message.
Taylor & Ratliff Expires August 3, 2018 [Page 3]
Internet-Draft Link Identifier Extension to DLEP January 2018
Because the MAC Address associated with any DLEP Destination Message
containing a Link Identifier Data Item is not the Layer 2 address of
the destination, all DLEP Destination Up Messages MUST contain Layer
3 information. In the case of modems that provide Layer 3 wide area
network connectivity between devices, this means one or more IPv4 or
IPv6 Address Data Items providing the Layer 3 address of the
destination. When referring to some upstream backbone network
infrastructure, this means one or more IPv4 or IPv6 Attached Subnet
Data Items, for example: '0.0.0.0/0' or '::/0'. This allows the DLEP
peer router to understand the properties of the link to those routes.
When the DLEP peer router wishes to forward packets to the Layer 3
destination or subnet, the MAC address associated with the link MUST
be used as the Layer 2 destination of the packet.
2.1. Identifier Restrictions
A link identifier is by default 4 octets in length. If a modem
wishes to use an identifier of a different length, it MUST be
announced using the Link Identifier Length Data Item (Section 3.1)
contained in the DLEP Session Initialization Response message sent by
the modem to the router.
During the lifetime of a DLEP session, the length of link identifiers
MUST remain constant, i.e. the Length field of the Link Identifier
Data Item must not alter between destinations.
The method for generating identifiers is a modem implementation
matter and out of scope of this document. Routers MUST NOT make any
assumptions about the meaning of identifiers, or how identifiers are
generated.
Within a single DLEP session, all link identifiers MUST be unique per
MAC Address. This means that a Layer 3 DLEP Destination is uniquely
identified by the pair: {MAC Address,Link Id}.
Identifiers MUST NOT be reused, i.e. a {MAC Address,Link Id} pair
that has been used to refer to one destination MUST NOT be recycled
to refer to a different destination within the lifetime of a single
DLEP session.
2.2. Negotiation
To use this extension, as with all DLEP extensions, the extension
MUST be announced during DLEP session initialization. A router
advertises support by including the value 'Link Identifiers' (TBD1),
Section 5, in the Extension Data Item within the Session
Initialization Message. A modem advertises support by including the
Taylor & Ratliff Expires August 3, 2018 [Page 4]
Internet-Draft Link Identifier Extension to DLEP January 2018
value 'Link Identifiers' (TBD1) in the Extension Data Item within the
Session Initialization Response Message. If both DLEP peers
advertise support for this extension then the Link Identifier Data
Item MAY be used.
If a modem requires support for this extension in order to describe
destinations, and the router does not advertise support, then the
modem MUST NOT include a Link Identifier Data Item in any DLEP
Message. However, the modem SHOULD NOT immediately terminate the
DLEP session, rather it SHOULD use session-wide DLEP Data Items to
announce general information about all reachable destinations via the
modem. By doing this, a modem allows a router not supporting this
extension to at least make a best guess at the state of any reachable
network. A modem MUST NOT attempt to re-use the MAC Address Data
Item to perform some kind of sleight-of-hand, assuming that the
router will notice the DLEP Peer Type of the modem is special in some
way.
3. New Data Items
This extension introduces two new DLEP Data Items: the Link
Identifier Data Item (Section 3.2) used to identify a Layer 3 link at
or beyond a destination, and the Link Identifier Length Data Item
(Section 3.1) used to announce the length of Link Identifiers at
session initialization.
3.1. Link Identifier Length Data Item
The Link Identifier Length Data Item MAY be used by a DLEP modem
implementation to define the length of Link Identifier Data Items if
it does not with to use the default value of 4 octets.
The Link Identifier Length Data Item MAY be used during Session
Initialization, contained in a Session Initialization Response
Message.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Item Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link Identifier Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Data Item Type: TBD2, Section 5
Length: 2
Taylor & Ratliff Expires August 3, 2018 [Page 5]
Internet-Draft Link Identifier Extension to DLEP January 2018
Link Identifier Length: The length, in octets, of Link Identifiers
used by the DLEP modem for this session.
3.2. Link Identifier Data Item
The Link Identifier Data Item MAY be used wherever a MAC Address Data
Item is defined as usable in core DLEP.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Data Item Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flags | Link Identifier... :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Data Item Type: TBD3, Section 5
Length: The length of the Data Item, by default 5, but may be
different if a Link Identifier Length Data Item (Section 3.1) has
been announced during session initialization.
Flags: Flags field, defined below.
Link Identifier: The unique identifier of the Layer 3 destination.
This identifier has no implicit meaning and is only used to
discriminate between multiple links.
The Flags field is defined as:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+
Reserved: MUST be zero. Left for future assignment.
4. Security Considerations
As an extension to the core DLEP protocol, the security
considerations of that protocol apply to this extension. This
extension adds no additional security mechanisms or features.
None of the features introduced by this extension require extra
consideration by an implementation.
Taylor & Ratliff Expires August 3, 2018 [Page 6]
Internet-Draft Link Identifier Extension to DLEP January 2018
5. IANA Considerations
Upon approval of this document, IANA is requested to:
o Assign a new value (TBD1) from the Specification Required section
of the DLEP Extensions Registry, named "Link Identifiers".
o Assign a new value (TBD2) from the Specification Required section
of the DLEP Data Item Type Values Registry, named "Link Identifier
Length".
o Assign a new value (TBD3) from the Specification Required section
of the DLEP Data Item Type Values Registry, named "Link
Identifier".
5.1. DLEP Link Identifier Flag
Upon approval of this document, IANA is requested to create a new
DLEP registry, named "Link Identifier Flags".
The following table provides initial registry values and the RFC 5226
defined policies that should apply to the registry:
+------------+------------------------------------+
| Bit | Description/Policy |
+------------+------------------------------------+
| 0-7 | Unassigned/Specification Required |
+------------+------------------------------------+
6. References
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997, <https://www.rfc-
editor.org/info/rfc2119>.
[RFC8175] Ratliff, S., Jury, S., Satterwhite, D., Taylor, R., and B.
Berry, "Dynamic Link Exchange Protocol (DLEP)", RFC 8175,
DOI 10.17487/RFC8175, June 2017, <https://www.rfc-
editor.org/info/rfc8175>.
6.2. Informative References
Taylor & Ratliff Expires August 3, 2018 [Page 7]
Internet-Draft Link Identifier Extension to DLEP January 2018
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", RFC 5226,
DOI 10.17487/RFC5226, May 2008, <https://www.rfc-
editor.org/info/rfc5226>.
Authors' Addresses
Rick Taylor
Airbus Defence & Space
Quadrant House
Celtic Springs
Coedkernew
Newport NP10 8FZ
UK
Email: rick.taylor@airbus.com
Stan Ratliff
VT iDirect
13861 Sunrise Valley Drive, Suite 300
Herndon, VA 20171
USA
Email: sratliff@idirect.net
Taylor & Ratliff Expires August 3, 2018 [Page 8]