Skip to main content

Mobility Header Home Agent Switch Message
draft-ietf-mip6-ha-switch-06

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 5142.
Authors James Kempf , Brian Haley , DENG Hui , Vijay Devarapalli
Last updated 2015-10-14 (Latest revision 2007-12-04)
Replaces draft-haley-mip6-ha-switch
RFC stream Internet Engineering Task Force (IETF)
Intended RFC status Proposed Standard
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state (None)
Document shepherd (None)
IESG IESG state Became RFC 5142 (Proposed Standard)
Action Holders
(None)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD Jari Arkko
Send notices to mext-chairs@ietf.org
draft-ietf-mip6-ha-switch-06
Mobile IPv6                                                 B. Haley
   Internet Draft                                       Hewlett-Packard
   Document: draft-ietf-mip6-ha-switch-06.txt            V. Devarapalli
   Intended status: Standards Track                     Azaire Networks
   Expires: June 4, 2008                                        H. Deng
                                                           China Mobile
                                                               J. Kempf
                                                        DoCoMo USA Labs
                                                       December 4, 2007

                 Mobility Header Home Agent Switch Message
                     draft-ietf-mip6-ha-switch-06.txt

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
        http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
        http://www.ietf.org/shadow.html

Abstract

   This document specifies a new Mobility Header message type that can
   be used between a home agent and mobile node to signal a mobile node
   that it should acquire a new home agent.

Haley, et al              Expires - May 2008                  [Page 1]

                      Home Agent Switch Message         December 2007

Table of Contents

   1. Introduction...................................................2
   2. Terminology....................................................3
   3. Scenarios......................................................3
      3.1 Overloaded.................................................3
      3.2 Load Balancing.............................................3
      3.3 Maintenance................................................3
      3.4 Functional Load Balancing..................................3
      3.5 Home Agent Renumbering.....................................4
   4. Home Agent Switch Message......................................4
   5. Home Agent Operation...........................................6
      5.1 Sending Home Agent Switch Messages.........................6
      5.2 Retransmissions............................................7
      5.3 Mobile Node Errors.........................................7
   6. Mobile Node Operation..........................................8
      6.1 Receiving Home Agent Switch Messages.......................8
      6.2 Selecting a Home Agent.....................................8
   7. Operational Considerations.....................................9
   8. Procotol Constants............................................10
   9. IANA Considerations...........................................10
   10. Security Considerations......................................10
   11. References...................................................10
      11.1 Normative References.....................................10
      11.2 Informative references...................................10
   Acknowledgments..................................................11
   Author's Addresses...............................................11

1. Introduction

   RFC 3775 [RFC3775] contains no provision to allow a home agent to
   inform a mobile node that it needs to stop acting as the home agent
   for the mobile node.  For example, a home agent may wish to handoff
   some of its mobile nodes to another home agent because it has become
   overloaded or it is going offline.

   This protocol describes a signaling message, called the Home Agent
   Switch message, that can be used to send a handoff notification
   between a home agent and mobile node.

   The Home Agent Switch message does not attempt to solve all general
   problems related to changing the home agent of a mobile node.  In
   particular, this protocol does not attempt to solve:

     o The case where the Home Address of a mobile node must change in
        order to switch to a new home agent.  This operation should be
        avoided using this message.

Haley, et al              Expires - May 2008                  [Page 2]

                      Home Agent Switch Message         December 2007

     o Determining when a home agent should actively move mobile nodes
        to another home agent.  This decision should be made by a
        backend protocol, for example, as described in [draft-mip6-
        hareliability].

2. Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC-2119 [RFC2119].

3. Scenarios

   Here are some example scenarios where a home agent signaling message
   would be useful.

3.1 Overloaded

   There are a number of reasons a home agent might be considered
   overloaded.  One might be that it is at, or near, its limit on the
   number of home bindings it is willing to accept.  Another is that it
   has reached a pre-determined level of system resource usage - memory,
   cpu cycles, etc.  In either case, it would be desirable for a home
   agent to reduce the number of home bindings before a failure occurs.

3.2 Load Balancing

   A home agent might know of other home agents that are not as heavily
   loaded as itself, learned through some other mechanism outside the
   scope of this document.  An operator may wish to try and balance this
   load so a failure disrupts a smaller percentage of mobile nodes.

3.3 Maintenance

   Most operators do periodic maintenance in order to maintain
   reliability.  If a home agent is being shutdown for maintenance, it
   would be desirable to inform mobile nodes so they do not lose
   mobility service.

3.4 Functional Load Balancing

   A Mobile IPv6 home agent provides mobile nodes with two basic
   services - a rendezvous server where correspondent nodes can find the
   current care-of address for the mobile node, and as an overlay router
   to tunnel traffic to/from the mobile node at its current care-of
   address.

   A mobility service provider could have two sets of home agents to
   handle the two functions.  The rendezvous function could be handled



Haley, et al              Expires - May 2008                  [Page 3]

                      Home Agent Switch Message         December 2007

   by a machine specialized for high-speed transaction processing, while
   the overlay router function could be handled by a machine with high
   data throughput.

   A mobile node would start on the rendezvous server home agent and
   stay there if it does route optimization.  However, if the original
   home agent detects that the mobile node is not doing route
   optimization, but instead reverse-tunneling traffic, it could
   redirect the mobile node to a home agent with better data throughput.

3.5 Home Agent Renumbering

   Periodically, a mobility service provider may want to shut-down home
   agent services at a set of IPv6 addresses and bring service back up
   at a new set of addresses.  Note that this may not involve anything
   as complex as IPv6 network renumbering [RFC4192], it may just involve
   changing the addresses of the home agents.  With a signaling message,
   the service provider could inform mobile nodes to look for a new home
   agent.

4. Home Agent Switch Message

   The Home Agent Switch message is used by the home agent to signal the
   mobile node that it needs to stop acting as the home agent for the
   mobile node, and that it should acquire a new home agent.  Home Agent
   Switch messages are sent as described in Section 5.

   The message described below follows the Mobility Header format
   specified in Section 6.1 of [RFC3775]:

    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Payload Proto |  Header Len   |   MH Type     |   Reserved    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |           Checksum            |                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               |
    |                                                               |
    .                                                               .
    .                       Message Data                            .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Haley, et al              Expires - May 2008                  [Page 4]

                      Home Agent Switch Message         December 2007

   The Home Agent Switch Message uses the MH Type value (TBD).  When
   this value is indicated in the MH Type field, the format of the
   Message Data field in the Mobility Header is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                   |# of Addresses |   Reserved    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   .                                                               .
   .                      Home Agent Addresses                     .
   .                                                               .
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   .                                                               .
   .                        Mobility options                       .
   .                                                               .
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   # of Addresses

     An 8-bit unsigned integer indicating the number of IPv6 home agent
     addresses in the message.  If set to zero, the mobile node MUST
     perform home agent discovery.

   Reserved

     8-bit field reserved for future use.  The value MUST be initialized
     to zero by the sender, and MUST be ignored by the receiver.

   Home Agent Addresses

     A list of alternate home agent addresses for the mobile node.  The
     number of addresses present in the list is indicated by the "# of
     Addresses" field in the Home Agent Switch message.

   Mobility options

     Variable-length field of such length that the complete Mobility
     Header is an integer multiple of 8 octets long.  This field

Haley, et al              Expires - May 2008                  [Page 5]

                      Home Agent Switch Message         December 2007

     contains zero or more TLV-encoded mobility options.  The encoding
     and format of defined options MUST follow the format specified in
     Section 6.2 of [RFC3775].  The receiver MUST ignore and skip any
     options which it does not understand.

     The Binding Refresh Advice mobility option defined in Section 6.2.4
     of [RFC3775] is valid for the Home Agent Switch message.

   If no home agent addresses and no options are present in this
   message, no padding is necessary and the Header Len field in the
   Mobility Header will be set to 0.

5. Home Agent Operation

5.1 Sending Home Agent Switch Messages

   When sending a Home Agent Switch message, the sending node constructs
   the packet as it would any other Mobility Header, except:

     o The MH Type field MUST be set to (TBD).

     o If alternative home agent addresses are known, the sending home
        agent SHOULD include them in the list of suggested alternate
        home agents.  The home agent addresses field should be
        constructed as described in Section 10.5.1 of [RFC3775], which
        will randomize addresses of the same preference in the list.

     o The "# of addresses" field MUST be filled-in corresponding to
        the number of home agent addresses included in the message.  If
        no addresses are present, the field MUST be set to zero, forcing
        the mobile node to perform home agent discovery by some other
        means.

     o If the home agent is able to continue offering services to the
        mobile node for some period of time, it MAY include a Binding
        Refresh Advice mobility option indicating the time (in units of
        4 seconds) until the binding will be deleted.

   The Home Agent Switch message MUST use the home agent to mobile node
   IPsec ESP authentication SA for integrity protection.

   A home agent SHOULD send a Home Agent Switch message when a known
   period of unavailability is pending so the mobile node has sufficient
   time to find another suitable home agent.

   The sending node does not need to be the current home agent for the
   mobile node, for example as described in [draft-mip6-hareliability],
   but it MUST have a security association with the mobile node so the

Haley, et al              Expires - May 2008                  [Page 6]

                      Home Agent Switch Message         December 2007

   message is not rejected.  In this case, the Home Agent Switch message
   SHOULD only contain the address of the home agent sending the message
   in the Home Agent Addresses field, which implies the mobile node
   should switch to using the sender as its new home agent.

5.2 Retransmissions

   If the home agent does not receive a response from the mobile node -
   either a Binding Update message to delete its home binding if it is
   the current home agent, or a Binding Update message to create a home
   binding if it is not the current home agent, then it SHOULD
   retransmit the message, until a response is received.  The initial
   value for the retransmission timer is INITIAL-HA-SWITCH-TIMEOUT.

   The retransmissions by the home agent MUST use an exponential back-
   off mechanism, in which the timeout period is doubled upon each
   retransmission, until either the home agent gets a response from the
   mobile node to delete its binding, or the timeout period reaches the
   value MAX-HA-SWITCH-TIMEOUT.  The home agent MAY continue to send
   these messages at this slower rate indefinitely.

   If the home agent included a Binding Refresh Advice mobility option,
   then it SHOULD delay any retransmissions until at least one half of
   the time period has expired, or INITIAL-HA-SWITCH-TIMEOUT, whichever
   value is less.

5.3 Mobile Node Errors

   If a mobile node does not understand how to process a Home Agent
   Switch Message, it will send a Binding Error message as described in
   Section 6.1.

   If a mobile node is unreachable, in other words, it still has a home
   binding with the home agent after reaching the timeout period of MAX-
   HA-SWITCH-TIMEOUT, the home agent SHOULD NOT make any conclusions
   about its status.

   In either case, the home agent SHOULD attempt to continue providing
   services until the lifetime of the binding expires.

   Attempts by the mobile node to extend the binding lifetime with a
   Binding Update message SHOULD be rejected, and a Binding
   Acknowledgement SHOULD be returned with status value 129
   (Administratively prohibited) as specified in Section 6.1.8 of
   [RFC3775].

Haley, et al              Expires - May 2008                  [Page 7]

                      Home Agent Switch Message         December 2007

6. Mobile Node Operation

6.1 Receiving Home Agent Switch Messages

   Upon receiving a Home Agent Switch message, the Mobility Header MUST
   be verified as specified in [RFC3775], specifically:

        o The Checksum, MH type, Payload Proto and Header Len fields
          MUST meet the requirements of Section 9.2 of [RFC3775].

        o The packet MUST be covered by the home agent to mobile node
          IPsec ESP authentication SA for integrity protection.

   If the packet is dropped due to the above tests, the receiving node
   MUST follow the processing rules as Section 9.2 of [RFC3775] defines.
   For example, it MUST send a Binding Error message with the Status
   field set to 2 (unrecognized MH Type value) if it does not support
   the message type.

   Upon receipt of a Home Agent Switch message, the mobile node MUST
   stop using its current home agent for services and MUST delete its
   home binding by sending a Binding Update message as described in
   Section 11.7.1 of [RFC3775].  This acts as an acknowledgement of the
   Home Agent Switch message.  Alternately, if the sender of the message
   is not the current home agent, sending a Binding Update message to
   create a home binding will act as an acknowledgement of the Home
   Agent Switch message.  Retransmissions of Binding Update messages
   MUST use the procedures described in Section 11.8 of [RFC3775].

   If a Binding Refresh Advice mobility option is present, the mobile
   node MAY delay the deletion of its home binding and continue to use
   its current home agent until the calculated time period has expired.

   If the Home Agent Switch message contains a list of alternate home
   agent addresses, the mobile node SHOULD select a new home agent as
   described in Section 6.2, and establish the necessary IPsec security
   associations with the new home agent by whatever means required as
   part of the mobile node/home agent bootstrapping protocol for the
   home agent's mobility service provider.  If no alternate home agent
   addresses are included in the list, the mobile node MUST first
   perform home agent discovery.

6.2 Selecting a Home Agent

   In most cases, the home agent addresses in the Home Agent Switch
   message will be of other home agents on the home link of the mobile
   node (the computed prefix is the same).  In this case, the mobile
   node SHOULD select a new home agent from the addresses as they are
   ordered in the list.  If the first address in the list is unable to

Haley, et al              Expires - May 2008                  [Page 8]

                      Home Agent Switch Message         December 2007

   provide service, then the subsequent addresses in the list should be
   tried in-order.

   In the case that the home agent addresses in the Home Agent Switch
   message are not all home agents on the home link of the mobile node
   (the computed prefix is different), the mobile node SHOULD select one
   its home network prefix first, if available, followed by home agents
   with other prefixes.  Choosing a home agent with a different prefix
   might require a change of the home address for the mobile node, which
   could cause a loss of connectivity for any connections using the
   current home address.

7. Operational Considerations

   This document does not specify how an operator might use the Home
   Agent Switch message in its network.  However, the following
   requirements are placed on the usage:

        o The use of this message needs to take into account possible
          signaling overhead, congestion, load from the mechanism
          itself, and the resulting registration to another home agent.
          A home agent may provide service for thousands, if not
          millions, of mobile nodes.  Careless application of the Home
          Agent Switch message may cause the new home agent, or some
          other parts of the network, to suffer.  As a result, it is
          REQUIRED that applications of this message either employ a
          feedback loop between resources of the new home agent and the
          sending of additional Home Agent Switch messages, or apply a
          maximum rate at which mobile nodes can be informed of the
          switch that is far below the designated capacity of new
          registrations that the set of home agents can process.  If no
          other information is available, this maximum rate should
          default to MAX-HA-SWITCH-TRANSMIT-RATE.

        o In general, switching the home agent of a mobile node should
          only be done when absolutely necessary, since it might cause
          a service disruption if the switch to a new home agent fails,
          the new home agent is itself under an overload condition, or
          the network connection of the new home agent is congested.
          Similarly, the path characteristics via the new home agent
          may be different, which may cause temporary difficulties for
          end to end transport layer operation.

        o If this message is being used for load-balancing between a set
          of home agents, they should all be configured with the same
          set of prefixes so a home agent switch does not require a
          change of the home address for a mobile node.  That operation
          is NOT RECOMMENDED and should be avoided.

Haley, et al              Expires - May 2008                  [Page 9]

                      Home Agent Switch Message         December 2007

8. Procotol Constants

   INITIAL-HA-SWITCH-TIMEOUT             5 seconds
   MAX-HA-SWITCH-TIMEOUT                 20 seconds
   MAX-HA-SWITCH-TRANSMIT-RATE           1 per second

9. IANA Considerations

   A new Mobility Header type is required for the following new message
   described in Section 4:

     (TBD) Home Agent Switch message

10. Security Considerations

   As with other messages in [RFC3775], the Home Agent Switch message
   MUST use the home agent to mobile node ESP encryption SA for
   confidentiality protection, and MUST use the home agent to mobile
   node ESP authentication SA for integrity protection.

   The Home Agent Switch message MAY use the IPsec ESP SA in place for
   Binding Updates and Acknowledgements as specified in Section 5.1 of
   [RFC3775], in order to reduce the number of configured security
   associations.  This also gives the message authenticity protection.

   Some operators may not want to reveal the list of home agents to on-
   path listeners.  In such a case, the Home Agent Switch message should
   use the home agent to mobile node IPsec ESP encryption SA for
   confidentiality protection.

11. References

11.1 Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
      Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3775] Johnson, D., Perkins, C., and Arkko, J., "Mobility Support
      in IPv6", RFC 3775, June, 2004.

11.2 Informative References

   [RFC4192] Baker, F., Lear, E., and Droms, R., "Procedures for
      Renumbering an IPv6 Network without a Flag Day", RFC 4192,
      September, 2005.



Haley, et al              Expires - May 2008                 [Page 10]

                      Home Agent Switch Message         December 2007

   [draft-mip6-hareliability] Wakikawa, R. (Editor), "Home Agent
      Reliability Protocol", draft-ietf-mip6-hareliability-02.txt, July,
      2007.

Acknowledgments

   We would like to thank the authors of a number of previous drafts
   that contributed content to this document:

        o draft-wakikawa-mip6-nemo-haha-spec-00.txt
        o draft-deng-mip6-ha-loadbalance-02.txt
        o draft-kempf-mip6-ha-alert-00.txt
        o draft-haley-mip6-mh-signaling-00.txt

   Thanks also to Kilian Weniger, Jixing Liu, Alexandru Petrescu, Jouni
   Korhonen, and Wolfgang Fritsche for their review and feedback.

Author's Addresses

   Brian Haley
   Hewlett-Packard Company
   110 Spitbrook Road
   Nashua, NH 03062, USA
   Email: brian.haley@hp.com

   Vijay Devarapalli
   Azaire Networks
   3121 Jay Street
   Santa Clara, CA 95054 USA
   Email: vijay.devarapalli@azairenet.com

   James Kempf
   DoCoMo USA Labs
   181 Metro Drive
   Suite 300
   San Jose, CA 95110 USA
   Email: kempf@docomolabs-usa.com

   Hui Deng
   China Mobile
   53A, Xibianmennei Ave.
   Xuanwu District
   Beijing 100053
   China
   Email: denghui@chinamobile.com

Full Copyright Statement

   Copyright (C) The IETF Trust (2007).

Haley, et al              Expires - May 2008                 [Page 11]

                      Home Agent Switch Message         December 2007

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgement

Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).

Haley, et al              Expires - May 2008                 [Page 12]