qlog: Structured Logging for Network Protocols
draft-ietf-quic-qlog-main-schema-13
| Document | Type | Active Internet-Draft (quic WG) | |
|---|---|---|---|
| Authors | Robin Marx , Luca Niccolini , Marten Seemann , Lucas Pardue | ||
| Last updated | 2025-10-20 | ||
| Replaces | draft-marx-qlog-main-schema | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Intended RFC status | Proposed Standard | ||
| Formats | |||
| Reviews | |||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Document | |
| Associated WG milestone |
|
||
| Document shepherd | (None) | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Yes | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-quic-qlog-main-schema-13
QUIC R. Marx, Ed.
Internet-Draft Akamai
Intended status: Standards Track L. Niccolini, Ed.
Expires: 23 April 2026 Meta
M. Seemann, Ed.
L. Pardue, Ed.
Cloudflare
20 October 2025
qlog: Structured Logging for Network Protocols
draft-ietf-quic-qlog-main-schema-13
Abstract
qlog provides extensible structured logging for network protocols,
allowing for easy sharing of data that benefits common debug and
analysis methods and tooling. This document describes key concepts
of qlog: formats, files, traces, events, and extension points. This
definition includes the high-level log file schemas, and generic
event schemas. Requirements and guidelines for creating protocol-
specific event schemas are also presented. All schemas are defined
independent of serialization format, allowing logs to be represented
in various ways such as JSON, CSV, or protobuf.
Note to Readers
Note to RFC editor: Please remove this section before publication.
Feedback and discussion are welcome at https://github.com/quicwg/qlog
(https://github.com/quicwg/qlog). Readers are advised to refer to
the "editor's draft" at that URL for an up-to-date version of this
document.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Marx, et al. Expires 23 April 2026 [Page 1]
Internet-Draft qlog October 2025
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 23 April 2026.
Copyright Notice
Copyright (c) 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Conventions and Terminology . . . . . . . . . . . . . . . 4
1.2. Use of CDDL . . . . . . . . . . . . . . . . . . . . . . . 5
2. Design Overview . . . . . . . . . . . . . . . . . . . . . . . 6
3. Abstract LogFile Class . . . . . . . . . . . . . . . . . . . 7
3.1. Concrete Log File Schema URIs . . . . . . . . . . . . . . 8
4. QlogFile schema . . . . . . . . . . . . . . . . . . . . . . . 9
4.1. Traces . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2. Trace . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3. TraceError . . . . . . . . . . . . . . . . . . . . . . . 12
5. QlogFileSeq schema . . . . . . . . . . . . . . . . . . . . . 13
5.1. TraceSeq . . . . . . . . . . . . . . . . . . . . . . . . 14
6. VantagePoint . . . . . . . . . . . . . . . . . . . . . . . . 15
7. Abstract Event Class . . . . . . . . . . . . . . . . . . . . 16
7.1. Timestamps . . . . . . . . . . . . . . . . . . . . . . . 17
7.2. Tuple . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.3. Grouping . . . . . . . . . . . . . . . . . . . . . . . . 23
7.4. SystemInformation . . . . . . . . . . . . . . . . . . . . 24
7.5. CommonFields . . . . . . . . . . . . . . . . . . . . . . 25
8. Concrete Event Types and Event Schemas . . . . . . . . . . . 27
8.1. Event Schema URIs . . . . . . . . . . . . . . . . . . . . 29
8.2. Extending the Data Field . . . . . . . . . . . . . . . . 29
8.2.1. Triggers . . . . . . . . . . . . . . . . . . . . . . 33
8.3. Event Importance Levels . . . . . . . . . . . . . . . . . 34
8.4. Tooling Expectations . . . . . . . . . . . . . . . . . . 35
Marx, et al. Expires 23 April 2026 [Page 2]
Internet-Draft qlog October 2025
8.5. Further Design Guidance . . . . . . . . . . . . . . . . . 35
9. The Generic Event Schemas . . . . . . . . . . . . . . . . . . 36
9.1. Loglevel events . . . . . . . . . . . . . . . . . . . . . 36
9.1.1. error . . . . . . . . . . . . . . . . . . . . . . . . 36
9.1.2. warning . . . . . . . . . . . . . . . . . . . . . . . 36
9.1.3. info . . . . . . . . . . . . . . . . . . . . . . . . 37
9.1.4. debug . . . . . . . . . . . . . . . . . . . . . . . . 37
9.1.5. verbose . . . . . . . . . . . . . . . . . . . . . . . 37
9.2. Simulation Events . . . . . . . . . . . . . . . . . . . . 38
9.2.1. scenario . . . . . . . . . . . . . . . . . . . . . . 38
9.2.2. marker . . . . . . . . . . . . . . . . . . . . . . . 38
10. Raw packet and frame information . . . . . . . . . . . . . . 39
11. Serializing qlog . . . . . . . . . . . . . . . . . . . . . . 40
11.1. qlog to JSON mapping . . . . . . . . . . . . . . . . . . 41
11.2. qlog to JSON Text Sequences mapping . . . . . . . . . . 41
11.2.1. Supporting JSON Text Sequences in tooling . . . . . 42
11.3. JSON Interoperability . . . . . . . . . . . . . . . . . 42
11.4. Truncated values . . . . . . . . . . . . . . . . . . . . 43
11.5. Optimization of serialized data . . . . . . . . . . . . 44
12. Methods of access and generation . . . . . . . . . . . . . . 45
12.1. Set file output destination via an environment
variable . . . . . . . . . . . . . . . . . . . . . . . . 45
13. Tooling requirements . . . . . . . . . . . . . . . . . . . . 46
14. Security and privacy considerations . . . . . . . . . . . . . 47
14.1. Data at risk . . . . . . . . . . . . . . . . . . . . . . 47
14.2. Operational implications and recommendations . . . . . . 48
14.3. Data minimization or anonymization . . . . . . . . . . . 49
15. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 49
16. References . . . . . . . . . . . . . . . . . . . . . . . . . 51
16.1. Normative References . . . . . . . . . . . . . . . . . . 51
16.2. Informative References . . . . . . . . . . . . . . . . . 53
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 54
Change Log . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Since draft-ietf-quic-qlog-main-schema-12: . . . . . . . . . . 54
Since draft-ietf-quic-qlog-main-schema-10: . . . . . . . . . . 54
Since draft-ietf-quic-qlog-main-schema-09: . . . . . . . . . . 54
Since draft-ietf-quic-qlog-main-schema-08: . . . . . . . . . . 55
Since draft-ietf-quic-qlog-main-schema-07: . . . . . . . . . . 55
Since draft-ietf-quic-qlog-main-schema-06: . . . . . . . . . . 55
Since draft-ietf-quic-qlog-main-schema-05: . . . . . . . . . . 55
Since draft-ietf-quic-qlog-main-schema-04: . . . . . . . . . . 55
Since draft-ietf-quic-qlog-main-schema-03: . . . . . . . . . . 55
Since draft-ietf-quic-qlog-main-schema-02: . . . . . . . . . . 56
Since draft-ietf-quic-qlog-main-schema-01: . . . . . . . . . . 56
Since draft-ietf-quic-qlog-main-schema-00: . . . . . . . . . . 56
Since draft-marx-qlog-main-schema-draft-02: . . . . . . . . . . 56
Since draft-marx-qlog-main-schema-01: . . . . . . . . . . . . . 56
Since draft-marx-qlog-main-schema-00: . . . . . . . . . . . . . 57
Marx, et al. Expires 23 April 2026 [Page 3]
Internet-Draft qlog October 2025
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 57
1. Introduction
Endpoint logging is a useful strategy for capturing and understanding
how applications using network protocols are behaving, particularly
where protocols have an encrypted wire image that restricts
observers' ability to see what is happening.
Many applications implement logging using a custom, non-standard
logging format. This has an effect on the tools and methods that are
used to analyze the logs, for example to perform root cause analysis
of an interoperability failure between distinct implementations. A
lack of a common format impedes the development of common tooling
that can be used by all parties that have access to logs.
qlog is an extensible structured logging for network protocols that
allows for easy sharing of data that benefits common debug and
analysis methods and tooling. This document describes key concepts
of qlog: formats, files, traces, events, and extension points. This
definition includes the high-level log file schemas, and generic
event schemas. Requirements and guidelines for creating protocol-
specific event schemas are also presented. Accompanying documents
define event schemas for QUIC ([QLOG-QUIC]) and HTTP/3 ([QLOG-H3]).
The goal of qlog is to provide amenities and default characteristics
that each logging file should contain (or should be able to contain),
such that generic and reusable toolsets can be created that can deal
with logs from a variety of different protocols and use cases.
As such, qlog provides versioning, metadata inclusion, log
aggregation, event grouping and log file size reduction techniques.
All qlog schemas can be serialized in many ways (e.g., JSON, CBOR,
protobuf, etc). This document describes only how to employ [JSON],
its subset [I-JSON], and its streamable derivative
[JSON-Text-Sequences].
1.1. Conventions and Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
Serialization examples in this document use JSON ([JSON]) unless
otherwise indicated.
Marx, et al. Expires 23 April 2026 [Page 4]
Internet-Draft qlog October 2025
Events are defined with an importance level as described in
Section 8.3}.
1.2. Use of CDDL
To define events and data structures, all qlog documents use the
Concise Data Definition Language [CDDL]. This document uses the
basic syntax, the specific text, uint, float32, float64, bool, and
any types, as well as the .default, .size, and .regexp control
operators, the ~ unwrapping operator, and the $ and $$ extension
points syntax from [CDDL].
Additionally, this document defines the following custom types for
clarity:
; CDDL's uint is defined as being 64-bit in size
; but for many protocol fields it is better to be restrictive
; and explicit
uint8 = uint .size 1
uint16 = uint .size 2
uint32 = uint .size 4
uint64 = uint .size 8
; an even-length lowercase string of hexadecimally encoded bytes
; examples: 82dc, 027339, 4cdbfd9bf0
; this is needed because the default CDDL binary string (bytes/bstr)
; is only CBOR and not JSON compatible
hexstring = text .regexp "([0-9a-f]{2})*"
Figure 1: Additional CDDL type definitions
All timestamps and time-related values (e.g., offsets) in qlog are
logged as float64 in the millisecond resolution.
Other qlog documents can define their own CDDL-compatible (struct)
types (e.g., separately for each Packet type that a protocol
supports).
The ordering of member fields in qlog CDDL type definitions is not
significant. The ordering of member fields in the serialization
formats defined in this document, JSON (Section 11.1) and JSON Text
Sequences (Section 11.2), is not significant and qlog tools MUST NOT
assume so. Other qlog serialization formats MAY define field order
significance, if they do they MUST define requirements for qlog tools
supporting those formats.
Note to RFC editor: Please remove the following text in this
section before publication.
Marx, et al. Expires 23 April 2026 [Page 5]
Internet-Draft qlog October 2025
The main general CDDL syntax conventions in this document a reader
should be aware of for easy reading comprehension are:
* ? obj : this object is optional
* TypeName1 / TypeName2 : a union of these two types (object can be
either type 1 OR type 2)
* obj: TypeName : this object has this concrete type
* obj: [* TypeName] : this object is an array of this type with
minimum size of 0 elements
* obj: [+ TypeName] : this object is an array of this type with
minimum size of 1 element
* TypeName = ... : defines a new type
* EnumName = "entry1" / "entry2" / entry3 / ...: defines an enum
* StructName = { ... } : defines a new struct type
* ; : single-line comment
* * text => any : special syntax to indicate 0 or more fields that
have a string key that maps to any value. Used to indicate a
generic JSON object.
All timestamps and time-related values (e.g., offsets) in qlog are
logged as float64 in the millisecond resolution.
Other qlog documents can define their own CDDL-compatible (struct)
types (e.g., separately for each Packet type that a protocol
supports).
2. Design Overview
The main tenets for the qlog design are:
* Streamable, event-based logging
* A flexible format that can reduce log producer overhead, at the
cost of increased complexity for consumers (e.g. tools)
* Extensible and pragmatic
Marx, et al. Expires 23 April 2026 [Page 6]
Internet-Draft qlog October 2025
* Aggregation and transformation friendly (e.g., the top-level
element for the non-streaming format is a container for individual
traces, group_ids can be used to tag events to a particular
context)
* Metadata is stored together with event data
This is achieved by a logical logging hierarchy of:
* Log file
- Trace(s)
o Event(s)
An abstract LogFile class is declared (Section 3), from which all
concrete log file formats derive using log file schemas. This
document defines the QLogFile (Section 4) and QLogFileSeq (Section 5)
log file schemas.
A trace is conceptually fluid but the conventional use case is to
group events related to a single data flow, such as a single logical
QUIC connection, at a single vantage point (Section 6). Concrete
trace definitions relate to the log file schemas they are contained
in; see (Section 4.1, Section 4.2, and Section 5.1).
Events are logged at a time instant and convey specific details of
the logging use case. For example, a network packet being sent or
received. This document declares an abstract Event class (Section 7)
containing common fields, which all concrete events derive from.
Concrete events are defined by event schemas that declare or extend a
namespace, which contains one or more related event types or their
extensions. For example, this document defines two event schemas for
two generic event namespaces loglevel and simulation (see Section 9).
3. Abstract LogFile Class
A Log file is intended to contain a collection of events that are in
some way related. An abstract LogFile class containing fields common
to all log files is defined in Figure 2. Each concrete log file
schema derives from this using the CDDL unwrap operator (~) and can
extend it by defining semantics and any custom fields.
Marx, et al. Expires 23 April 2026 [Page 7]
Internet-Draft qlog October 2025
LogFile = {
file_schema: text
serialization_format: text
? title: text
? description: text
}
Figure 2: LogFile definition
The required "file_schema" field identifies the concrete log file
schema. It MUST have a value that is an absolute URI; see
Section 3.1 for rules and guidance.
The required "serialization_format" field indicates the serialization
format using a media type [RFC2046]. It is case-insensitive.
In order to make it easier to parse and identify qlog files and their
serialization format, the "file_schema" and "serialization_format"
fields and their values SHOULD be in the first 256 characters/bytes
of the resulting log file.
The optional "title" and "description" fields provide additional
free-text information about the file.
3.1. Concrete Log File Schema URIs
Concrete log file schemas MUST identify themselves using a URI
[RFC3986].
Log file schemas defined by RFCs MUST register a URI in the "qlog log
file schema URIs" registry and SHOULD use a URN of the form
urn:ietf:params:qlog:file:<schema-identifier>, where <schema-
identifier> is a globally-unique text name using only characters in
the URI unreserved range; see Section 2.3 of [RFC3986]. This
document registers urn:ietf:params:qlog:file:contained (Section 4)
and urn:ietf:params:qlog:file:sequential (Section 5).
Marx, et al. Expires 23 April 2026 [Page 8]
Internet-Draft qlog October 2025
Private or non-standard log file schemas MAY register a URI in the
"qlog log file schema URIs" registry but MUST NOT use a URN of the
form urn:ietf:params:qlog:file:<schema-identifier>. URIs that
contain a domain name SHOULD also contain a month-date in the form
mmyyyy. For example, "https://example.org/072024/
globallyuniquelogfileschema". The definition of the log file schema
and assignment of the URI MUST have been authorized by the owner of
the domain name on or very close to that date. This avoids problems
when domain names change ownership. The URI does not need to be
dereferencable, allowing for confidential use or to cover the case
where the log file schema continues to be used after the organization
that defined them ceases to exist.
The "qlog log file schema URIs" registry operates under the Expert
Review policy, per Section 4.5 of [RFC8126]. When reviewing
requests, the expert MUST check that the URI is appropriate to the
concrete log file schema and satisfies the requirements in this
section. A request to register a private or non-standard log file
schema URI using a URN of the form urn:ietf:params:qlog:file:<schema-
identifier> MUST be rejected.
Registration requests should use the template defined in Section 15.
4. QlogFile schema
A qlog file using the QlogFile schema can contain several individual
traces and logs from multiple vantage points that are in some way
related. The top-level element in this schema defines only a small
set of "header" fields and an array of component traces. This is
defined in Figure 3 as:
QlogFile = {
~LogFile
? traces: [+ Trace /
TraceError]
}
Figure 3: QlogFile definition
The QlogFile schema URI is urn:ietf:params:qlog:file:contained.
QlogFile extends LogFile using the CDDL unwrap operator (~), which
copies the fields presented in Section 3. Additionally, the optional
"traces" field contains an array of qlog traces (Section 4.2), each
of which contain metadata and an array of qlog events (Section 7).
Marx, et al. Expires 23 April 2026 [Page 9]
Internet-Draft qlog October 2025
The default serialization format for QlogFile is JSON; see
Section 11.1 for guidance on populating the "serialization_format"
field and other considerations. Where a qlog file is serialized to a
JSON format, one of the downsides is that it is inherently a non-
streamable format. Put differently, it is not possible to simply
append new qlog events to a log file without "closing" this file at
the end by appending "]}]}". Without these closing tags, most JSON
parsers will be unable to parse the file entirely. The alternative
QlogFileSeq (Section 5) is better suited to streaming use cases.
JSON serialization example:
{
"file_schema": "urn:ietf:params:qlog:file:contained",
"serialization_format": "application/qlog+json",
"title": "Name of this particular qlog file (short)",
"description": "Description for this group of traces (long)",
"traces": [...]
}
Figure 4: QlogFile example
4.1. Traces
It can be advantageous to group several related qlog traces together
in a single file. For example, it is possible to simultaneously
perform logging on the client, on the server, and on a single point
on their common network path. For analysis, it is useful to
aggregate these three individual traces together into a single file,
so it can be uniquely stored, transferred, and annotated.
The QlogFile "traces" field is an array that contains a list of
individual qlog traces. When capturing a qlog at a vantage point, it
is expected that the traces field contains a single entry. Files can
be aggregated, for example as part of a post-processing operation, by
copying the traces in component to files into the combined "traces"
array of a new, aggregated qlog file.
4.2. Trace
The exact conceptual definition of a Trace can be fluid. For
example, a trace could contain all events for a single connection,
for a single endpoint, for a single measurement interval, for a
single protocol, etc. In the normal use case however, a trace is a
log of a single data flow collected at a single location or vantage
point. For example, for QUIC, a single trace only contains events
for a single logical QUIC connection for either the client or the
server.
Marx, et al. Expires 23 April 2026 [Page 10]
Internet-Draft qlog October 2025
A Trace contains some metadata in addition to qlog events, defined in
Figure 5 as:
Trace = {
? title: text
? description: text
? common_fields: CommonFields
? vantage_point: VantagePoint
event_schemas: [+text]
events: [* Event]
}
Figure 5: Trace definition
The optional "title" and "description" fields provide additional
free-text information about the trace.
The optional "common_fields" field is described in Section 7.5.
The optional "vantage_point" field is described in Section 6.
The required "event_schemas" field contains event schema URIs that
identify concrete event namespaces and their associated types
recorded in the "events" field. Requirements and guidelines are
defined in Section 8.
The semantics and context of the trace can mainly be deduced from the
entries in the "common_fields" list and "vantage_point" field.
JSON serialization example:
Marx, et al. Expires 23 April 2026 [Page 11]
Internet-Draft qlog October 2025
{
"title": "Name of this particular trace (short)",
"description": "Description for this trace (long)",
"common_fields": {
"ODCID": "abcde1234",
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "system",
"epoch": "1970-01-01T00:00:00.000Z"
},
},
"vantage_point": {
"name": "backend-67",
"type": "server"
},
"event_schemas": ["urn:ietf:params:qlog:events:quic"],
"events": [...]
}
Figure 6: Trace example
4.3. TraceError
A TraceError indicates that an attempt to find/convert a file for
inclusion in the aggregated qlog was made, but there was an error
during the process. Rather than silently dropping the erroneous
file, it can be explicitly included in the qlog file as an entry in
the "traces" array, defined in Figure 7 as:
TraceError = {
error_description: text
; the original URI used for attempted find of the file
? uri: text
? vantage_point: VantagePoint
}
Figure 7: TraceError definition
JSON serialization example:
{
"error_description": "File could not be found",
"uri": "/srv/traces/today/latest.qlog",
"vantage_point": { type: "server" }
}
Figure 8: TraceError example
Marx, et al. Expires 23 April 2026 [Page 12]
Internet-Draft qlog October 2025
Note that another way to combine events of different traces in a
single qlog file is through the use of the "group_id" field,
discussed in Section 7.3.
5. QlogFileSeq schema
A qlog file using the QlogFileSeq schema can be serialized to a
streamable JSON format called JSON Text Sequences (JSON-SEQ)
([RFC7464]). The top-level element in this schema defines only a
small set of "header" fields and an array of component traces. This
is defined in Figure 3 as:
QlogFileSeq = {
~LogFile
trace: TraceSeq
}
Figure 9: QlogFileSeq definition
The QlogFileSeq schema URI is urn:ietf:params:qlog:file:sequential.
QlogFile extends LogFile using the CDDL unwrap operator (~), which
copies the fields presented in Section 3. Additionally, the required
"trace" field contains a singular trace (Section 4.2). All qlog
events in the file are related to this trace; see Section 5.1.
See Section 11.2 for guidance on populating the
"serialization_format" field and other serialization considerations.
JSON-SEQ serialization example:
Marx, et al. Expires 23 April 2026 [Page 13]
Internet-Draft qlog October 2025
// list of qlog events, serialized in accordance with RFC 7464,
// starting with a Record Separator character and ending with a
// newline.
// For display purposes, Record Separators are rendered as <RS>
<RS>{
"file_schema": "urn:ietf:params:qlog:file:sequential",
"serialization_format": "application/qlog+json-seq",
"title": "Name of JSON Text Sequence qlog file (short)",
"description": "Description for this trace file (long)",
"trace": {
"common_fields": {
"group_id":"127ecc830d98f9d54a42c4f0842aa87e181a",
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "system",
"epoch": "1970-01-01T00:00:00.000Z"
},
},
"vantage_point": {
"name":"backend-67",
"type":"server"
},
"event_schemas": ["urn:ietf:params:qlog:events:quic",
"urn:ietf:params:qlog:events:http3"]
}
}
<RS>{"time": 2, "name": "quic:parameters_set", "data": { ... } }
<RS>{"time": 7, "name": "quic:packet_sent", "data": { ... } }
...
Figure 10: Top-level element
5.1. TraceSeq
TraceSeq is used with QlogFileSeq. It is conceptually similar to a
Trace, with the exception that qlog events are not contained within
it, but rather appended after it in a QlogFileSeq.
TraceSeq = {
? title: text
? description: text
? common_fields: CommonFields
? vantage_point: VantagePoint
event_schemas: [+text]
}
Figure 11: TraceSeq definition
Marx, et al. Expires 23 April 2026 [Page 14]
Internet-Draft qlog October 2025
6. VantagePoint
A VantagePoint describes the vantage point from which a trace
originates, defined in Figure 12 as:
VantagePoint = {
? name: text
type: VantagePointType
? flow: VantagePointType
}
; client = endpoint which initiates the connection
; server = endpoint which accepts the connection
; network = observer in between client and server
VantagePointType = "client" /
"server" /
"network" /
"unknown"
Figure 12: VantagePoint definition
JSON serialization examples:
{
"name": "aioquic client",
"type": "client"
}
{
"name": "wireshark trace",
"type": "network",
"flow": "client"
}
Figure 13: VantagePoint example
The flow field is only required if the type is "network" (for
example, the trace is generated from a packet capture). It is used
to disambiguate events like "packet sent" and "packet received".
This is indicated explicitly because for multiple reasons (e.g.,
privacy) data from which the flow direction can be otherwise inferred
(e.g., IP addresses) might not be present in the logs.
Meaning of the different values for the flow field:
* "client" indicates that this vantage point follows client data
flow semantics (a "packet sent" event goes in the direction of the
server).
Marx, et al. Expires 23 April 2026 [Page 15]
Internet-Draft qlog October 2025
* "server" indicates that this vantage point follow server data flow
semantics (a "packet sent" event goes in the direction of the
client).
* "unknown" indicates that the flow's direction is unknown.
Depending on the context, tools confronted with "unknown" values in
the vantage_point can either try to heuristically infer the semantics
from protocol-level domain knowledge (e.g., in QUIC, the client
always sends the first packet) or give the user the option to switch
between client and server perspectives manually.
7. Abstract Event Class
Events are logged at a time instant and convey specific details of
the logging use case. An abstract Event class containing fields
common to all events is defined in Figure 14.
Event = {
time: float64
name: text
data: $ProtocolEventData
? tuple: TupleID
? time_format: TimeFormat
? group_id: GroupID
? system_info: SystemInformation
; events can contain any amount of custom fields
* text => any
}
Figure 14: Event definition
Each qlog event MUST contain the mandatory fields: "time"
(Section 7.1), "name" (Section 8), and "data" (Section 8.2).
Each qlog event is an instance of a concrete event type that derives
from the abstract Event class; see Section 8. They extend it by
defining the specific values and semantics of common fields, in
particular the name and data fields. Furthermore, they can
optionally add custom fields.
Each qlog event MAY contain the optional fields: "time_format"
(Section 7.1), tuple (Section 7.2) "trigger" (Section 8.2.1), and
"group_id" (Section 7.3).
Marx, et al. Expires 23 April 2026 [Page 16]
Internet-Draft qlog October 2025
Multiple events can appear in a Trace or TraceSeq and they might
contain fields with identical values. It is possible to optimize out
this duplication using "common_fields" (Section 7.5).
Example qlog event:
{
"time": 1553986553572,
"name": "quic:packet_sent",
"data": { ... },
"group_id": "127ecc830d98f9d54a42c4f0842aa87e181a",
"time_format": "relative_to_epoch",
"ODCID": "127ecc830d98f9d54a42c4f0842aa87e181a"
}
Figure 15: Event example
7.1. Timestamps
Each event MUST include a "time" field to indicate the timestamp that
it occurred. It is a duration measured from some point in time; its
units depend on the type of clock chosen and system used. The time
field is a float64 and it is typically used to represent a duration
in milliseconds, with a fractional component to microsecond or
nanosecond resolution.
There are several options for generating and logging timestamps,
these are governed by the ReferenceTime type (optionally included in
the "reference_time" field contained in a trace's "common_fields"
(Section 7.5)) and TimeFormat type (optionally included in the
"time_format" field contained in the event itself, or a trace's
"common_fields").
There is no requirement that events in the same trace use the same
time format. However, using a single time format for related events
can make them easier to analyze.
The reference time governs from which point in time the "time" field
values are measured and is defined as:
Marx, et al. Expires 23 April 2026 [Page 17]
Internet-Draft qlog October 2025
ReferenceTime = {
clock_type: "system" / "monotonic" / text .default "system"
epoch: RFC3339DateTime / "unknown" .default "1970-01-01T00:00:00.000Z"
? wall_clock_time: RFC3339DateTime
}
RFC3339DateTime = text
Figure 16: ReferenceTime definition
The required "clock_type" field represents the type of clock used for
time measurements. The value "system" represents a clock that uses
system time, commonly measured against a chosen or well-known epoch.
However, depending on the system, System time can potentially jump
forward or back. In contrast, a clock using monotonic time is
generally guaranteed to never go backwards. The value "monotonic"
represents such a clock.
The required "epoch" field is the start of the ReferenceTime. When
using the "system" clock type, the epoch field SHOULD have a date/
time value using the format defined in [RFC3339]. However, the value
"unknown" MAY be used.
When using the "monotonic" clock type, the epoch field MUST have the
value "unknown".
The optional "wall_clock_time" field can be used to provide an
approximate date/time value that logging commenced at if the epoch
value is "unknown". It uses the format defined in [RFC3339]. Note
that conversion of timestamps to calendar time based on wall clock
times cannot be safely relied on.
The time format details how "time" values are encoded relative to the
reference time and is defined as:
TimeFormat = "relative_to_epoch" /
"relative_to_previous_event" .default "relative_to_epoch"
Figure 17: TimeFormat definition
relative_to_epoch: A duration relative to the ReferenceTime "epoch"
field. This approach uses the largest amount of characters. It
is good for stateless loggers. This is the default value of the
"time_format" field.
relative_to_previous_event: A delta-encoded value, based on the
Marx, et al. Expires 23 April 2026 [Page 18]
Internet-Draft qlog October 2025
previously logged value. The first event in a trace is always
relative to the ReferenceTime. This approach uses the least
amount of characters. It is suitable for stateful loggers.
Events in each individual trace SHOULD be logged in strictly
ascending timestamp order (though not necessarily absolute value, for
the "relative_to_previous_event" format). Tools MAY sort all events
on the timestamp before processing them, though are not required to
(as this could impose a significant processing overhead). This can
be a problem especially for multi-threaded and/or streaming loggers,
who could consider using a separate post-processor to order qlog
events in time if a tool do not provide this feature.
Tools SHOULD NOT assume the ability to derive the absolute calendar
timestamp of an event from qlog traces. Tools should not rely on
timestamps to be consistent across traces, even those generated by
the same logging endpoint. For reasons of privacy, the reference
time MAY have minimization or anonymization applied.
Example of a log using the relative_to_epoch format:
Marx, et al. Expires 23 April 2026 [Page 19]
Internet-Draft qlog October 2025
"common_fields": {
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "system",
"epoch": "1970-01-01T00:00:00.000Z"
},
},
"events": [
{
"time": 1553986553572,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 1553986553577,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 1553986553587,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 1553986553597,
"name": "quic:packet_received",
"data": { ... },
},
]
Figure 18: Relative to epoch timestamps
Example of a log using the relative_to_previous_event format:
Marx, et al. Expires 23 April 2026 [Page 20]
Internet-Draft qlog October 2025
"common_fields": {
"time_format": "relative_to_previous_event",
"reference_time": {
"clock_type": "system",
"epoch": "1970-01-01T00:00:00.000Z"
},
},
"events": [
{
"time": 1553986553572,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 5,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 10,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 10,
"name": "quic:packet_received",
"data": { ... },
},
]
Figure 19: Relative-to-previous-event timestamps
Example of a monotonic log using the relative_to_epoch format:
Marx, et al. Expires 23 April 2026 [Page 21]
Internet-Draft qlog October 2025
"common_fields": {
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "monotonic",
"epoch": "unknown",
"wall_clock_time": "2024-10-10T10:10:10.000Z"
},
},
"events": [
{
"time": 0,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 5,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 15,
"name": "quic:packet_received",
"data": { ... },
},
{
"time": 25,
"name": "quic:packet_received",
"data": { ... },
},
]
Figure 20: Monotonic timestamps
7.2. Tuple
A qlog event is typically associated with a single network "path",
which is usually aligned with a four-tuple of IP addresses and ports.
In many cases, this tuple will be the same for all events in a given
trace, and does not need to be logged explicitly with each event. In
this case, the "tuple" field can be omitted (in which case the
default value of "" is assumed) or reflected in "common_fields"
instead (see Section 7.5).
However, in some situations, such as during QUIC's Connection
Migration or when using Multipath features, it is useful to be able
to split events across multiple (concurrent) tuples and/or paths.
Definition:
Marx, et al. Expires 23 April 2026 [Page 22]
Internet-Draft qlog October 2025
TupleID = text .default ""
Figure 21: TupleID definition
The "tuple" field is an identifier that is associated with a single
network four-tuple. This document intentionally does not define
further how to choose this identifier's value per-tuple or how to
potentially log other parameters that can be associated with such a
tuple. This is left for other documents. Implementers are free to
encode tuple information directly into the TupleID or to log
associated info in a separate event. For example, QUIC has the
"tuple_assigned" event to couple the TupleID value to a specific
tuple configuration, see [QLOG-QUIC].
7.3. Grouping
As discussed in Section 4.2, a single qlog file can contain several
traces taken from different vantage points. However, a single trace
from one endpoint can also contain events from a variety of sources.
For example, a server implementation might choose to log events for
all incoming connections in a single large (streamed) qlog file. As
such, a method for splitting up events belonging to separate logical
entities is required.
The simplest way to perform this splitting is by associating a "group
id" to each event that indicates to which conceptual "group" each
event belongs. A post-processing step can then extract events per
group. However, this group identifier can be highly protocol and
context-specific. In the example above, the QUIC "Original
Destination Connection ID" could be used to uniquely identify a
connection. As such, they might add a "ODCID" field to each event.
Additionally, a service providing different levels of Quality of
Service (QoS) to their users might wish to group connections per QoS
level applied. They might instead prefer a "qos" field.
As such, to provide consistency and ease of tooling in cross-protocol
and cross-context setups, qlog instead defines the common "group_id"
field, which contains a string value. Implementations are free to
use their preferred string serialization for this field, so long as
it contains a unique value per logical group. Some examples can be
seen in Figure 23.
GroupID = text
Figure 22: GroupID definition
Marx, et al. Expires 23 April 2026 [Page 23]
Internet-Draft qlog October 2025
JSON serialization example for events grouped either by QUIC
Connection IDs, or according to an endpoint-specific Quality of
Service (QoS) logic that includes the service level:
"events": [
{
"time": 1553986553579,
"group_id": "qos=premium",
"name": "quic:packet_received",
"data": { ... }
},
{
"time": 1553986553581,
"group_id": "127ecc830d98f9d54a42c4f0842aa87e181a",
"name": "quic:packet_sent",
"data": { ... }
}
]
Figure 23: GroupID example
Note that in some contexts (for example a Multipath transport
protocol) it might make sense to add additional contextual per-event
fields (for example TupleID, see Section 7.2), rather than use the
group_id field for that purpose.
Note also that, typically, a single trace only contains events
belonging to a single logical group (for example, an individual QUIC
connection). As such, instead of logging the "group_id" field with
an identical value for each event instance, this field is typically
logged once in "common_fields", see Section 7.5.
7.4. SystemInformation
The "system_info" field can be used to record system-specific details
related to an event. This is useful, for instance, where an
application splits work across CPUs, processes, or threads and events
for a single trace occur on potentially different combinations
thereof. Each field is optional to support deployment diversity.
SystemInformation = {
? processor_id: uint32
? process_id: uint32
? thread_id: uint32
}
Marx, et al. Expires 23 April 2026 [Page 24]
Internet-Draft qlog October 2025
7.5. CommonFields
As discussed in the previous sections, information for a typical qlog
event varies in three main fields: "time", "name" and associated
data. Additionally, there are also several more advanced fields that
allow mixing events from different protocols and contexts inside of
the same trace (for example "group_id"). In most "normal" use cases
however, the values of these advanced fields are consistent for each
event instance (for example, a single trace contains events for a
single QUIC connection).
To reduce file size and making logging easier, qlog uses the
"common_fields" list to indicate those fields and their values that
are shared by all events in this component trace. This prevents
these fields from being logged for each individual event. An example
of this is shown in Figure 24.
JSON serialization with repeated field values
per-event instance:
{
"events": [{
"group_id": "127ecc830d98f9d54a42c4f0842aa87e181a",
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "system",
"epoch": "2019-03-29T:22:55:53.572Z"
},
"time": 2,
"name": "quic:packet_received",
"data": { ... }
},{
"group_id": "127ecc830d98f9d54a42c4f0842aa87e181a",
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "system",
"epoch": "2019-03-29T:22:55:53.572Z"
},
"time": 7,
"name": "http:frame_parsed",
"data": { ... }
}
]
}
JSON serialization with repeated field values instead
Marx, et al. Expires 23 April 2026 [Page 25]
Internet-Draft qlog October 2025
extracted to common_fields:
{
"common_fields": {
"group_id": "127ecc830d98f9d54a42c4f0842aa87e181a",
"time_format": "relative_to_epoch",
"reference_time": {
"clock_type": "system",
"epoch": "2019-03-29T:22:55:53.572Z"
},
},
"events": [
{
"time": 2,
"name": "quic:packet_received",
"data": { ... }
},{
"time": 7,
"name": "http:frame_parsed",
"data": { ... }
}
]
}
Figure 24: CommonFields example
An event's "common_fields" field is a generic dictionary of key-value
pairs, where the key is always a string and the value can be of any
type, but is typically also a string or number. As such, unknown
entries in this dictionary MUST be disregarded by the user and tools
(i.e., the presence of an unknown field is explicitly NOT an error).
The list of default qlog fields that are typically logged in
common_fields (as opposed to as individual fields per event instance)
are shown in the listing below:
CommonFields = {
? tuple: TupleID
? time_format: TimeFormat
? reference_time: ReferenceTime
? group_id: GroupID
* text => any
}
Figure 25: CommonFields definition
Marx, et al. Expires 23 April 2026 [Page 26]
Internet-Draft qlog October 2025
Tools MUST be able to deal with these fields being defined either on
each event individually or combined in common_fields. Note that if
at least one event in a trace has a different value for a given
field, this field MUST NOT be added to common_fields but instead
defined on each event individually. Good example of such fields are
"time" and "data", who are divergent by nature.
8. Concrete Event Types and Event Schemas
Concrete event types, as well as related data types, are grouped in
event namespaces which in turn are defined in one or multiple event
schemas.
As an example, the QUICPacketSent and QUICPacketHeader event and data
types would be part of the quic namespace, which is defined in an
event schema with URI urn:ietf:params:qlog:events:quic. A later
extension that adds a new QUIC frame QUICNewFrame would also be part
of the quic namespace, but defined in a new event schema with URI
urn:ietf:params:qlog:events:quic#new-frame-extension.
Concrete event types MUST belong to a single event namespace and MUST
have a registered non-empty identifier of type text.
New namespaces MUST have a registered non-empty globally-unique text
identifier using only characters in the URI unreserved range; see
Section 2.3 of [RFC3986]. Namespaces are mutable and MAY be extended
with new events.
The value of a qlog event name field MUST be the concatenation of
namespace identifier, colon (':'), and event type identifier (for
example: quic:packet_sent). The resulting concatenation MUST be
globally unique, so log files can contain events from multiple event
schemas without the risk of name collisions.
A single event schema can contain exactly one of the below:
* A definition for a new event namespace
* An extension of an existing namespace (adding new events/data
types and/or extending existing events/data types within the
namespace with new fields)
A single document can define multiple event schemas (for example see
Section 9).
An event schema MUST have a single URI [RFC3986] that MUST be
absolute. The URI MUST include the namespace identifier. Event
schemas that extend an existing namespace MUST furthermore include a
Marx, et al. Expires 23 April 2026 [Page 27]
Internet-Draft qlog October 2025
non-empty globally-unique "extension" identifier using a URI fragment
(characters after a "#" in the URI) using only characters in the URI
unreserved range; see Section 2.3 of [RFC3986]. Registration
guidance and requirement for event schema URIs are provided in
Section 8.1. Event schemas by themselves are immutable and MUST NOT
be extended.
Implementations that record concrete event types SHOULD list all
event schemas in use. This is achieved by including the appropriate
URIs in the event_schemas field of the Trace (Section 4.2) and
TraceSeq (Section 5.1) classes. The event_schemas is a hint to tools
about the possible event namespaces, their extensions, and the event
types/data types contained therein, that a qlog trace might contain.
The trace MAY still contain event types that do not belong to a
listed event schema. Inversely, not all event types associated with
an event schema listed in event_schemas are guaranteed to be logged
in a qlog trace. Tools MUST NOT treat either of these as an error;
see Section 13.
In the following hypothetical example, a qlog trace contains events
belonging to:
* The two event namespaces defined by event schemas in this document
(Section 9).
* Events in a namespace named rick specified in a hypothetical RFC
* Extentions to the rick namespace defined in two separate new event
schemas (with URI extension identifiers astley and moranis)
* Events from three private event schemas, detailing definitions for
and extensions to two namespaces (pickle and cucumber)
The standardized schema URIs use a URN format, the private schemas
use a URI with domain name.
"event_schemas": [
"urn:ietf:params:qlog:events:loglevel",
"urn:ietf:params:qlog:events:simulation",
"urn:ietf:params:qlog:events:rick",
"urn:ietf:params:qlog:events:rick#astley",
"urn:ietf:params:qlog:events:rick#moranis",
"https://example.com/032024/pickle.html",
"https://example.com/032024/pickle.html#lilly",
"https://example.com/032025/cucumber.html"
]
Figure 26: Example event_schemas serialization
Marx, et al. Expires 23 April 2026 [Page 28]
Internet-Draft qlog October 2025
8.1. Event Schema URIs
Event schemas defined by RFCs MUST register all namespaces and
concrete event types they contain in the "qlog event schema URIs"
registry.
Event schemas that define a new namespace SHOULD use a URN of the
form urn:ietf:params:qlog:events:<namespace identifier>, where
<namespace identifier> is globally unique. For example, this
document defines two event schemas (Section 9) for two namespaces:
loglevel and sim. Other examples of event schema define the quic
[QLOG-QUIC] and http3 [QLOG-H3] namespaces.
Event schemas that extend an existing namespace SHOULD use a URN of
the form urn:ietf:params:qlog:events:<namespace
identifier>#<extension identifier>, where the combination of
<namespace identifier> and <extension identifier> is globally unique.
Private or non-standard event schemas MAY be registered in the "qlog
event schema URIs" registry but MUST NOT use a URN of the forms
outlined above. URIs that contain a domain name SHOULD also contain
a month-date in the form mmyyyy. For example,
"https://example.org/072024/customeventschema#customextension". The
definition of the event schema and assignment of the URI MUST have
been authorized by the owner of the domain name on or very close to
that date. This avoids problems when domain names change ownership.
The URI does not need to be dereferencable, allowing for confidential
use or to cover the case where the event schemas continue to be used
after the organization that defined them ceases to exist.
The "qlog event schema URIs" registry operates under the Expert
Review policy, per Section 4.5 of [RFC8126]. When reviewing
requests, the expert MUST check that the URI is appropriate to the
event schema and satisfies the requirements in Section 8 and this
section. A request to register a private or non-standard schema URI
using a URN of the forms reserved for schemas defined by an RFC above
MUST be rejected.
Registration requests should use the template defined in Section 15.
8.2. Extending the Data Field
An event's "data" field is a generic key-value map (e.g., JSON
object). It defines the per-event metadata that is to be logged.
Its specific subfields and their semantics are defined per concrete
event type. For example, data field definitions for QUIC and HTTP/3
can be found in [QLOG-QUIC] and [QLOG-H3].
Marx, et al. Expires 23 April 2026 [Page 29]
Internet-Draft qlog October 2025
In order to keep qlog fully extensible, two separate CDDL extension
points ("sockets" or "plugs") are used to fully define data fields.
Firstly, to allow existing data field definitions to be extended (for
example by adding an additional field needed for a new protocol
feature), a CDDL "group socket" is used. This takes the form of a
subfield with a name of * $$NAMESPACE-EVENTTYPE-extension. This
field acts as a placeholder that can later be replaced with newly
defined fields by assigning them to the socket with the //= operator.
Multiple extensions can be assigned to the same group socket. An
example is shown in Figure 27.
; original definition in event schema A
MyNSEventX = {
field_a: uint8
* $$myns-eventx-extension
}
; later extension of EventX in event schema B
$$myns-eventx-extension //= (
? additional_field_b: bool
)
; another extension of EventX in event schema C
$$myns-eventx-extension //= (
? additional_field_c: text
)
; if schemas A, B and C are then used in conjunction,
; the combined MyNSEventX CDDL is equivalent to this:
MyNSEventX = {
field_a: uint8
? additional_field_b: bool
? additional_field_c: text
}
Figure 27: Example of using a generic CDDL group socket to extend
an existing event data definition
Secondly, to allow documents to define fully new event data field
definitions (as opposed to extend existing ones), a CDDL "type
socket" is used. For this purpose, the type of the "data" field in
the qlog Event type (see Figure 14) is the extensible
$ProtocolEventData type. This field acts as an open enum of possible
types that are allowed for the data field. As such, any new event
data field is defined as its own CDDL type and later merged with the
Marx, et al. Expires 23 April 2026 [Page 30]
Internet-Draft qlog October 2025
existing $ProtocolEventData enum using the /= extension operator.
Any generic key-value map type can be assigned to $ProtocolEventData.
The example in Figure 28 demonstrates $ProtocolEventData being
extended with two types.
; We define two new concrete events in a new event schema
MyNSEvent1 /= {
field_1: uint8
* $$myns-event1-extension
}
MyNSEvent2 /= {
field_2: bool
* $$myns-event2-extension
}
; the events are both merged with the existing
; $ProtocolEventData type enum
$ProtocolEventData /= MyNSEvent1 / MyNSEvent2
; the "data" field of a qlog event can now also be of type
; MyNSEvent1 and MyNSEvent2
Figure 28: ProtocolEventData extension
Event schema defining new qlog events MUST properly extend
$ProtocolEventData when defining data fields to enable automated
validation of aggregated qlog schemas. Furthermore, they SHOULD add
a * $$NAMESPACE-EVENTTYPE-extension extension field to newly defined
event data to allow the new events to be properly extended by other
event schema.
A combined but purely illustrative example of the use of both
extension points for a conceptual QUIC "packet_sent" event is shown
in Figure 29:
Marx, et al. Expires 23 April 2026 [Page 31]
Internet-Draft qlog October 2025
; defined in the main QUIC event schema
QUICPacketSent = {
? packet_size: uint16
header: QUICPacketHeader
? frames:[* QUICFrame]
* $$quic-packetsent-extension
}
; Add the event to the global list of recognized qlog events
$ProtocolEventData /= QUICPacketSent
; Defined in a separate event schema that describes a
; theoretical QUIC protocol extension
$$quic-packetsent-extension //= (
? additional_field: bool
)
; If both schemas are utilized at the same time,
; the following JSON serialization would pass an automated
; CDDL schema validation check:
{
"time": 123456,
"name": "quic:packet_sent",
"data": {
"packet_size": 1280,
"header": {
"packet_type": "1RTT",
"packet_number": 123
},
"frames": [
{
"frame_type": "stream",
"offset": 456
},
{
"frame_type": "padding"
}
],
additional_field: true
}
}
Figure 29: Example of an extended 'data' field for a conceptual
QUIC packet_sent event
Marx, et al. Expires 23 April 2026 [Page 32]
Internet-Draft qlog October 2025
8.2.1. Triggers
It can be useful to understand the cause or trigger of an event.
Sometimes, events are caused by a variety of other events and
additional information is needed to identify the exact details.
Commonly, the context of the surrounding log messages gives a hint
about the cause. However, in highly-parallel and optimized
implementations, corresponding log messages might be separated in
time, making it difficult to build an accurate context.
Including a "trigger" as part of the event itself is one method for
providing fine-grained information without much additional overhead.
In circumstances where a trigger is useful, it is RECOMMENDED for the
purpose of consistency that the event data definition contains an
optional field named "trigger", holding a string value.
For example, the QUIC "packet_dropped" event (Section 5.7 of
[QLOG-QUIC]) includes a trigger field that identifies the precise
reason why a QUIC packet was dropped:
QUICPacketDropped = {
; Primarily packet_type should be filled here,
; as other fields might not be decrypteable or parseable
? header: PacketHeader
? raw: RawInfo
? datagram_id: uint32
? details: {* text => any}
? trigger:
"internal_error" /
"rejected" /
"unsupported" /
"invalid" /
"duplicate" /
"connection_unknown" /
"decryption_failure" /
"key_unavailable" /
"general"
* $$quic-packetdropped-extension
}
Figure 30: Trigger example
Marx, et al. Expires 23 April 2026 [Page 33]
Internet-Draft qlog October 2025
8.3. Event Importance Levels
Depending on how events are designed, it may be that several events
allow the logging of similar or overlapping data. For example the
separate QUIC connection_started event overlaps with the more generic
connection_state_updated. In these cases, it is not always clear
which event should be logged or used, and which event should take
precedence if e.g., both are present and provide conflicting
information.
To aid in this decision making, qlog defines three event importance
levels, in decreasing order of importance and expected usage:
* Core
* Base
* Extra
Concrete event types SHOULD define an importance level.
Core-level events SHOULD be present in all qlog files for a given
protocol. These are typically tied to basic packet and frame parsing
and creation, as well as listing basic internal metrics. Tool
implementers SHOULD expect and add support for these events, though
SHOULD NOT expect all Core events to be present in each qlog trace.
Base-level events add additional debugging options and MAY be present
in qlog files. Most of these can be implicitly inferred from data in
Core events (if those contain all their properties), but for many it
is better to log the events explicitly as well, making it clearer how
the implementation behaves. These events are for example tied to
passing data around in buffers, to how internal state machines
change, and used to help show when decisions are actually made based
on received data. Tool implementers SHOULD at least add support for
showing the contents of these events, if they do not handle them
explicitly.
Extra-level events are considered mostly useful for low-level
debugging of the implementation, rather than the protocol. They
allow more fine-grained tracking of internal behavior. As such, they
MAY be present in qlog files and tool implementers MAY add support
for these, but they are not required to.
Note that in some cases, implementers might not want to log for
example data content details in Core-level events due to performance
or privacy considerations. In this case, they SHOULD use (a subset
of) relevant Base-level events instead to ensure usability of the
Marx, et al. Expires 23 April 2026 [Page 34]
Internet-Draft qlog October 2025
qlog output. As an example, implementations that do not log QUIC
packet_received events and thus also not which (if any) ACK frames
the packet contains, SHOULD log packets_acked events instead.
Finally, for event types whose data (partially) overlap with other
event types' definitions, where necessary the event definition
document should include explicit guidance on which to use in specific
situations.
8.4. Tooling Expectations
qlog is an extensible format and it is expected that new event schema
will emerge that define new namespaces, event types, event fields
(e.g., a field indicating an event's privacy properties), as well as
values for the "trigger" property within the "data" field, or other
member fields of the "data" field, as they see fit.
It SHOULD NOT be expected that general-purpose tools will recognize
or visualize all forms of qlog extension. Tools SHOULD allow for the
presence of unknown event fields and make an effort to visualize even
unknown data if possible, otherwise they MUST ignore it.
8.5. Further Design Guidance
There are several ways of defining concrete event types. In
practice, two main types of approach have been observed: a) those
that map directly to concepts seen in the protocols (e.g.,
packet_sent) and b) those that act as aggregating events that combine
data from several possible protocol behaviors or code paths into one
(e.g., parameters_set). The latter are typically used as a means to
reduce the amount of unique event definitions, as reflecting each
possible protocol event as a separate qlog entity would cause an
explosion of event types.
Additionally, logging duplicate data is typically prevented as much
as possible. For example, packet header values that remain
consistent across many packets are split into separate events (for
example spin_bit_updated or connection_id_updated for QUIC).
Finally, when logging additional state change events, those state
changes can often be directly inferred from data on the wire (for
example flow control limit changes). As such, if the implementation
is bug-free and spec-compliant, logging additional events is
typically avoided. Exceptions have been made for common events that
benefit from being easily identifiable or individually logged (for
example packets_acked).
Marx, et al. Expires 23 April 2026 [Page 35]
Internet-Draft qlog October 2025
9. The Generic Event Schemas
The two following generic event schemas define two namespaces and
several concrete event types that are common across protocols,
applications, and use cases.
9.1. Loglevel events
In typical logging setups, users utilize a discrete number of well-
defined logging categories, levels or severities to log freeform
(string) data. The loglevel event namespace replicates this approach
to allow implementations to fully replace their existing text-based
logging by qlog. This is done by providing events to log generic
strings for the typical well-known logging levels (error, warning,
info, debug, verbose). The namespace identifier is "loglevel". The
event schema URI is urn:ietf:params:qlog:events:loglevel.
LogLevelEventData = LogLevelError /
LogLevelWarning /
LogLevelInfo /
LogLevelDebug /
LogLevelVerbose
$ProtocolEventData /= LogLevelEventData
Figure 31: LogLevelEventData and ProtocolEventData extension
The event types are further defined below, their identifier is the
heading name.
9.1.1. error
Used to log details of an internal error that might not get reflected
on the wire. It has Core importance level.
LogLevelError = {
? code: uint64
? message: text
* $$loglevel-error-extension
}
Figure 32: LogLevelError definition
9.1.2. warning
Used to log details of an internal warning that might not get
reflected on the wire. It has Base importance level.
Marx, et al. Expires 23 April 2026 [Page 36]
Internet-Draft qlog October 2025
LogLevelWarning = {
? code: uint64
? message: text
* $$loglevel-warning-extension
}
Figure 33: LogLevelWarning definition
9.1.3. info
Used mainly for implementations that want to use qlog as their one
and only logging format but still want to support unstructured string
messages. The event has Extra importance level.
LogLevelInfo = {
message: text
* $$loglevel-info-extension
}
Figure 34: LogLevelInfo definition
9.1.4. debug
Used mainly for implementations that want to use qlog as their one
and only logging format but still want to support unstructured string
messages. The event has Extra importance level.
LogLevelDebug = {
message: text
* $$loglevel-debug-extension
}
Figure 35: LogLevelDebug definition
9.1.5. verbose
Used mainly for implementations that want to use qlog as their one
and only logging format but still want to support unstructured string
messages. The event has Extra importance level.
LogLevelVerbose = {
message: text
* $$loglevel-verbose-extension
}
Marx, et al. Expires 23 April 2026 [Page 37]
Internet-Draft qlog October 2025
Figure 36: LogLevelVerbose definition
9.2. Simulation Events
When evaluating a protocol implementation, one typically sets up a
series of interoperability or benchmarking tests, in which the test
situations can change over time. For example, the network bandwidth
or latency can vary during the test, or the network can be fully
disable for a short time. In these setups, it is useful to know when
exactly these conditions are triggered, to allow for proper
correlation with other events. This namespace defines event types to
allow logging of such simulation metadata and its identifier is
"simulation". The event schema URI is
urn:ietf:params:qlog:events:simulation.
SimulationEventData = SimulationScenario /
SimulationMarker
$ProtocolEventData /= SimulationEventData
Figure 37: SimulationEventData and ProtocolEventData extension
The event types are further defined below, their identifier is the
heading name.
9.2.1. scenario
Used to specify which specific scenario is being tested at this
particular instance. This supports, for example, aggregation of
several simulations into one trace (e.g., split by group_id). It has
Extra importance level; see Section 8.3.
SimulationScenario = {
? name: text
? details: {* text => any }
* $$simulation-scenario-extension
}
Figure 38: SimulationScenario definition
9.2.2. marker
Used to indicate when specific emulation conditions are triggered at
set times (e.g., at 3 seconds in 2% packet loss is introduced, at 10s
a NAT rebind is triggered). It has Extra importance level.
Marx, et al. Expires 23 April 2026 [Page 38]
Internet-Draft qlog October 2025
SimulationMarker = {
? type: text
? message: text
* $$simulation-marker-extension
}
Figure 39: SimulationMarker definition
10. Raw packet and frame information
While qlog is a high-level logging format, it also allows the
inclusion of most raw wire image information, such as byte lengths
and byte values. This is useful when for example investigating or
tuning packetization behavior or determining encoding/framing
overheads. However, these fields are not always necessary, can take
up considerable space, and can have a considerable privacy and
security impact (see Section 14). Where applicable, these fields are
grouped in a separate, optional, field named "raw" of type RawInfo.
The exact definition of entities, headers, trailers and payloads
depend on the protocol used.
RawInfo = {
; the full byte length of the entity (e.g., packet or frame),
; including possible headers and trailers
? length: uint64
; the byte length of the entity's payload,
; excluding possible headers or trailers
? payload_length: uint64
; the (potentially truncated) contents of the full entity,
; including headers and possibly trailers
? data: hexstring
}
Figure 40: RawInfo definition
All fields in RawInfo are defined as optional. It is acceptable to
log any field without the others. Logging length related fields and
omitting the data field permits protocol debugging without the risk
of logging potentially sensitive data. The data field, if logged, is
not required to contain the contents of a full entity and can be
truncated, see Section 11.4. The length fields, if logged, should
indicate the length of the the full entity, even if the data field is
omitted or truncated.
Marx, et al. Expires 23 April 2026 [Page 39]
Internet-Draft qlog October 2025
Protocol entities containing an on-the-wire length field (for example
a packet header or QUIC's stream frame) are strongly recommended to
re-use the raw.length field instead of defining a separate length
field, to maintain consistency and prevent data duplication.
This document does not specify explicit header_length or
trailer_length fields. In protocols without trailers, header_length
can be calculated by subtracting the payload_length from the length.
In protocols with trailers (e.g., QUIC's AEAD tag), event definition
documents SHOULD define how to support header_length calculation.
11. Serializing qlog
qlog schema definitions in this document are intentionally agnostic
to serialization formats. The choice of format is an implementation
decision.
Other documents related to qlog (for example event definitions for
specific protocols), SHOULD be similarly agnostic to the employed
serialization format and SHOULD clearly indicate this. If not, they
MUST include an explanation on which serialization formats are
supported and on how to employ them correctly.
Serialization formats make certain tradeoffs between usability,
flexibility, interoperability, and efficiency. Implementations
should take these into consideration when choosing a format. Some
examples of possible formats are JSON, CBOR, CSV, protocol buffers,
flatbuffers, etc. which each have their own characteristics. For
instance, a textual format like JSON can be more flexible than a
binary format but more verbose, typically making it less efficient
than a binary format. A plaintext readable (yet relatively large)
format like JSON is potentially more usable for users operating on
the logs directly, while a more optimized yet restricted format can
better suit the constraints of a large scale operation. A custom or
restricted format could be more efficient for analysis with custom
tooling but might not be interoperable with general-purpose qlog
tools.
Considering these tradeoffs, JSON-based serialization formats provide
features that make them a good starting point for qlog flexibility
and interoperability. For these reasons, JSON is a recommended
default and expanded considerations are given to how to map qlog to
JSON (Section 11.1, and its streaming counterpart JSON Text Sequences
(Section 11.2. Section 11.3 presents interoperability considerations
for both formats, and Section 11.5 presents potential optimizations.
Marx, et al. Expires 23 April 2026 [Page 40]
Internet-Draft qlog October 2025
Serialization formats require appropriate deserializers/parsers. The
"serialization_format" field (Section 3) is used to indicate the
chosen serialization format.
11.1. qlog to JSON mapping
As described in Section 4, JSON is the default qlog serialization.
When mapping qlog to normal JSON, QlogFile (Figure 3) is used. The
Media Type is "application/qlog+json" per [RFC6839]. The file
extension/suffix SHOULD be ".qlog".
In accordance with Section 8.1 of [RFC8259], JSON files are required
to use UTF-8 both for the file itself and the string values it
contains. In addition, all qlog field names MUST be lowercase when
serialized to JSON.
In order to serialize CDDL-based qlog event and data structure
definitions to JSON, the official CDDL-to-JSON mapping defined in
Appendix E of [CDDL] SHOULD be employed.
11.2. qlog to JSON Text Sequences mapping
One of the downsides of using normal JSON is that it is inherently a
non-streamable format. A qlog serializer could work around this by
opening a file, writing the required opening data, streaming qlog
events by appending them, and then finalizing the log by appending
appropriate closing tags e.g., "]}]}". However, failure to append
closing tags, could lead to problems because most JSON parsers will
fail if a document is malformed. Some streaming JSON parsers are
able to handle missing closing tags, however they are not widely
deployed in popular environments (e.g., Web browsers)
To overcome the issues related to JSON streaming, a qlog mapping to a
streamable JSON format called JSON Text Sequences (JSON-SEQ)
([RFC7464]) is provided.
JSON Text Sequences are very similar to JSON, except that objects are
serialized as individual records, each prefixed by an ASCII Record
Separator (<RS>, 0x1E), and each ending with an ASCII Line Feed
character (\n, 0x0A). Note that each record can also contain any
amount of newlines in its body, as long as it ends with a newline
character before the next <RS> character.
Marx, et al. Expires 23 April 2026 [Page 41]
Internet-Draft qlog October 2025
In order to leverage the streaming capability, each qlog event is
serialized and interpreted as an individual JSON Text Sequence
record, that is appended as a new object to the back of an event
stream or log file. Put differently, unlike default JSON, it does
not require a document to be wrapped as a full object with "{ ... }"
or "[... ]".
This alternative record streaming approach cannot be accommodated by
QlogFile (Figure 3). Instead, QlogFileSeq is defined in Figure 9,
which notably includes only a single trace (TraceSeq) and omits an
explicit "events" array. An example is provided in Figure 10. The
"group_id" field can still be used on a per-event basis to include
events from conceptually different sources in a single JSON-SEQ qlog
file.
When mapping qlog to JSON-SEQ, the Media Type is "application/
qlog+json-seq" per [RFC8091]. The file extension/suffix SHOULD be
".sqlog" (for "streaming" qlog).
While not specifically required by the JSON-SEQ specification, all
qlog field names MUST be lowercase when serialized to JSON-SEQ.
In order to serialize all other CDDL-based qlog event and data
structure definitions to JSON-SEQ, the official CDDL-to-JSON mapping
defined in Appendix E of [CDDL] SHOULD be employed.
11.2.1. Supporting JSON Text Sequences in tooling
Note that JSON Text Sequences are not supported in most default
programming environments (unlike normal JSON). However, several
custom JSON-SEQ parsing libraries exist in most programming languages
that can be used and the format is easy enough to parse with existing
implementations (i.e., by splitting the file into its component
records and feeding them to a normal JSON parser individually, as
each record by itself is a valid JSON object).
11.3. JSON Interoperability
Some JSON implementations have issues with the full JSON format,
especially those integrated within a JavaScript environment (e.g.,
Web browsers, NodeJS). I-JSON (Internet-JSON) is a subset of JSON
for such environments; see [I-JSON]. One of the key limitations of
JavaScript, and thus I-JSON, is that it cannot represent full 64-bit
integers in standard operating mode (i.e., without using BigInt
extensions), instead being limited to the range -(2^53)+1 to (2^53)-
1.
Marx, et al. Expires 23 April 2026 [Page 42]
Internet-Draft qlog October 2025
To accommodate such constraints in CDDL, Appendix E of [CDDL]
recommends defining new CDDL types for int64 and uint64 that limit
their values to the restricted 64-bit integer range. However, some
of the protocols that qlog is intended to support (e.g., QUIC,
HTTP/3), can use the full range of uint64 values.
As such, to support situations where I-JSON is in use, seralizers MAY
encode uint64 values using JSON strings. qlog parsers, therefore,
SHOULD support parsing of uint64 values from JSON strings or JSON
numbers unless there is out-of-band information indicating that
neither the serializer nor parser are constrained by I-JSON.
11.4. Truncated values
For some use cases (e.g., limiting file size, privacy), it can be
necessary not to log a full raw blob (using the hexstring type) but
instead a truncated value. For example, one might only store the
first 100 bytes of an HTTP response body to be able to discern which
file it actually contained. In these cases, the original byte-size
length cannot be obtained from the serialized value directly.
As such, all qlog schema definitions SHOULD include a separate,
length-indicating field for all fields of type hexstring they
specify, see for example Section 10. This not only ensures the
original length can always be retrieved, but also allows the omission
of any raw value bytes of the field completely (e.g., out of privacy
or security considerations).
To reduce overhead however and in the case the full raw value is
logged, the extra length-indicating field can be left out. As such,
tools SHOULD be able to deal with this situation and derive the
length of the field from the raw value if no separate length-
indicating field is present. The main possible permutations are
shown by example in Figure 41.
Marx, et al. Expires 23 April 2026 [Page 43]
Internet-Draft qlog October 2025
// both the content's value and its length are present
// (length is redundant)
{
"content_length": 5,
"content": "051428abff"
}
// only the content value is present, indicating it
// represents the content's full value. The byte
// length is obtained by calculating content.length / 2
{
"content": "051428abff"
}
// only the length is present, meaning the value
// was omitted
{
"content_length": 5,
}
// both value and length are present, but the lengths
// do not match: the value was truncated to
// the first three bytes.
{
"content_length": 5,
"content": "051428"
}
Figure 41: Example for serializing truncated hexstrings
11.5. Optimization of serialized data
Both the JSON and JSON-SEQ formatting options described above are
serviceable in general small to medium scale (debugging) setups.
However, these approaches tend to be relatively verbose, leading to
larger file sizes. Additionally, generalized JSON(-SEQ)
(de)serialization performance is typically (slightly) lower than that
of more optimized and predictable formats. Both aspects present
challenges to large scale setups, though they may still be practical
to deploy; see [ANRW-2020]. JSON and JSON-SEQ compress very well
using commonly-available algorithms such as GZIP or Brotli.
During the development of qlog, a multitude of alternative formatting
and optimization options were assessed and the results are summarized
on the qlog github repository (https://github.com/quiclog/internet-
drafts/issues/30#issuecomment-617675097).
Marx, et al. Expires 23 April 2026 [Page 44]
Internet-Draft qlog October 2025
Formal definition of additional qlog formats or encodings that use
the optimization techniques described here, or any other optimization
technique is left to future activity that can apply the following
guidelines.
In order to help tools correctly parse and process serialized qlog,
it is RECOMMENDED that new formats also define suitable file
extensions and media types. This provides a clear signal and avoids
the need to provide out-of-band information or to rely on heuristic
fallbacks; see Section 13.
12. Methods of access and generation
Different implementations will have different ways of generating and
storing qlogs. However, there is still value in defining a few
default ways in which to steer this generation and access of the
results.
12.1. Set file output destination via an environment variable
To provide users control over where and how qlog files are created,
two environment variables are defined. The first, QLOGFILE,
indicates a full path to where an individual qlog file should be
stored. This path MUST include the full file extension. The second,
QLOGDIR, sets a general directory path in which qlog files should be
placed. This path MUST include the directory separator character at
the end.
In general, QLOGDIR should be preferred over QLOGFILE if an endpoint
is prone to generate multiple qlog files. This can for example be
the case for a QUIC server implementation that logs each QUIC
connection in a separate qlog file. An alternative that uses
QLOGFILE would be a QUIC server that logs all connections in a single
file and uses the "group_id" field (Section 7.3) to allow post-hoc
separation of events.
Implementations SHOULD provide support for QLOGDIR and MAY provide
support for QLOGFILE.
When using QLOGDIR, it is up to the implementation to choose an
appropriate naming scheme for the qlog files themselves. The chosen
scheme will typically depend on the context or protocols used. For
example, for QUIC, it is recommended to use the Original Destination
Connection ID (ODCID), followed by the vantage point type of the
logging endpoint. Examples of all options for QUIC are shown in
Figure 42.
Marx, et al. Expires 23 April 2026 [Page 45]
Internet-Draft qlog October 2025
Command: QLOGFILE=/srv/qlogs/client.qlog quicclientbinary
Should result in the the quicclientbinary executable logging a
single qlog file named client.qlog in the /srv/qlogs directory.
This is for example useful in tests when the client sets up
just a single connection and then exits.
Command: QLOGDIR=/srv/qlogs/ quicserverbinary
Should result in the quicserverbinary executable generating
several logs files, one for each QUIC connection.
Given two QUIC connections, with ODCID values "abcde" and
"12345" respectively, this would result in two files:
/srv/qlogs/abcde_server.qlog
/srv/qlogs/12345_server.qlog
Command: QLOGFILE=/srv/qlogs/server.qlog quicserverbinary
Should result in the the quicserverbinary executable logging
a single qlog file named server.qlog in the /srv/qlogs directory.
Given that the server handled two QUIC connections before it was
shut down, with ODCID values "abcde" and "12345" respectively,
this would result in event instances in the qlog file being
tagged with the "group_id" field with values "abcde" and "12345".
Figure 42: Environment variable examples for a QUIC implementation
13. Tooling requirements
Tools ingestion qlog MUST indicate which qlog version(s), qlog
format(s), qlog file and event schema(s), compression methods and
potentially other input file formats (for example .pcap) they
support. Tools SHOULD at least support .qlog files in the default
JSON format (Section 11.1). Additionally, they SHOULD indicate
exactly which values for and properties of the name
(namespace:event_type) and data fields they look for to execute their
logic. Tools SHOULD perform a (high-level) check if an input qlog
file adheres to the expected qlog file and event schemas. If a tool
determines a qlog file does not contain enough supported information
to correctly execute the tool's logic, it SHOULD generate a clear
error message to this effect.
Tools MUST NOT produce breaking errors for any field names and/or
values in the qlog format that they do not recognize. Tools SHOULD
indicate even unknown event occurrences within their context (e.g.,
marking unknown events on a timeline for manual interpretation by the
user).
Marx, et al. Expires 23 April 2026 [Page 46]
Internet-Draft qlog October 2025
Tool authors should be aware that, depending on the logging
implementation, some events will not always be present in all traces.
For example, using a circular logging buffer of a fixed size, it
could be that the earliest events (e.g., connection setup events) are
later overwritten by "newer" events. Alternatively, some events can
be intentionally omitted out of privacy or file size considerations.
Tool authors are encouraged to make their tools robust enough to
still provide adequate output for incomplete logs.
14. Security and privacy considerations
Protocols such as TLS [RFC8446] and QUIC [RFC9000] offer secure
protection for the wire image [RFC8546]. Logging can reveal aspects
of the wire image that would ordinarily be protected, creating
tension between observability, security and privacy, especially if
data can be correlated across data sources.
qlog permits logging of a broad and detailed range of data.
Operators and implementers are responsible for deciding what data is
logged to address their requirements and constraints. As per
[RFC6973], operators must be aware that data could be compromised,
risking the privacy of all participants. Where entities expect
protocol features to ensure data privacy, logging might unknowingly
be subject to broader privacy risks, undermining their ability to
assess or respond effectively.
14.1. Data at risk
qlog operators and implementers need to consider security and privacy
risks when handling qlog data, including logging, storage, usage, and
more. The considerations presented in this section may pose varying
risks depending on the the data itself or its handling.
The following is a non-exhaustive list of example data types that
could contain sensitive information that might allow identification
or correlation of individual connections, endpoints, users or
sessions across qlog or other data sources (e.g., captures of
encrypted packets):
* IP addresses and transport protocol port numbers.
* Session, Connection, or User identifiers e.g., QUIC Connection IDs
Section 9.5 of [RFC9000]).
* System-level information e.g., CPU, process, or thread
identifiers.
Marx, et al. Expires 23 April 2026 [Page 47]
Internet-Draft qlog October 2025
* Stored State e.g., QUIC address validation and retry tokens, TLS
session tickets, and HTTP cookies.
* TLS decryption keys, passwords, and HTTP-level API access or
authorization tokens.
* High-resolution event timestamps or inter-event timings, event
counts, packet sizes, and frame sizes.
* Full or partial raw packet and frame payloads that are encrypted.
* Full or partial raw packet and frame payloads that are plaintext
e.g., HTTP Field values, HTTP response data, or TLS SNI field
values.
14.2. Operational implications and recommendations
Operational considerations should focus on authorizing capture and
access to logs. Logging of Internet protocols using qlog can be
equivalent to the ability to store or read plaintext communications.
Without a more detailed analysis, all of the security considerations
of plaintext access apply.
It is recommended that qlog capture is subject to access control and
auditing. These controls should support granular levels of
information capture based on role and permissions (e.g., capture of
more-sensitive data requires higher privileges).
It is recommended that access to stored qlogs is subject to access
control and auditing.
End users might not understand the implications of qlog to security
or privacy, and their environments might limit access control
techniques. Implementations should make enabling qlog conspicuous
(e.g., requiring clear and explicit actions to start a capture) and
resistant to social engineering, automation, or drive-by attacks; for
example, isolation or sandboxing of capture from other activities in
the same process or component.
It is recommended that data retention policies are defined for the
storage of qlog files.
It is recommended that qlog files are encrypted in transit and at
rest.
Marx, et al. Expires 23 April 2026 [Page 48]
Internet-Draft qlog October 2025
14.3. Data minimization or anonymization
Applying data minimization or anonymization techniques to qlog might
help address some security and privacy risks. However, removing or
anonymizing data without sufficient care might not enhance privacy or
security and could diminish the utility of qlog data.
Operators and implementers should balance the value of logged data
with the potential risks of voluntary or involuntary disclosure to
trusted or untrusted entities. Importantly, both the breadth and
depth of the data needed to make it useful, as well as the definition
of entities depend greatly on the intended use cases. For example, a
research project might be tightly scoped, time bound, and require
participants to explicitly opt in to having their data collected with
the intention for this to be shared in a publication. Conversely, a
server administrator might desire to collect telemetry, from users
whom they have no relationship with, for continuing operational
needs.
The most extreme form of minimization or anonymization is deleting a
field, equivalent to not logging it. qlog implementations should
offer fine-grained control for this on a per-use-case or per-
connection basis.
Data can undergo anonymization, pseudonymization, permutation,
truncation, re-encryption, or aggregation; see Appendix B of
[DNS-PRIVACY] for techniques, especially regarding IP addresses.
However, operators should be cautious because many anonymization
methods have been shown to be insufficient to safeguard user privacy
or identity, particularly with large or easily correlated data sets.
Operators should consider end user rights and preferences. Active
user participation (as indicated by [RFC6973]) on a per-qlog basis is
challenging but aligning qlog capture, storage, and removal with
existing user preference and privacy controls is crucial. Operators
should consider agressive approaches to deletion or aggregation.
The most sensitive data in qlog is typically contained in RawInfo
type fields (see Section 10). Therefore, qlog users should exercise
caution and limit the inclusion of such fields for all but the most
stringent use cases.
15. IANA Considerations
IANA is requested to register a new entry in the "IETF URN Sub-
namespace for Registered Protocol Parameter Identifiers" registry
([RFC3553])":
Marx, et al. Expires 23 April 2026 [Page 49]
Internet-Draft qlog October 2025
Registered Parameter Identifier: qlog
Reference: This Document
IANA Registry Reference: <https://www.iana.org/assignments/qlog>
IANA is requested to create the "qlog log file schema URIs" registry
at https://www.iana.org/assignments/qlog for the purpose of
registering log file schema. It has the following format/template:
Log File Schema URI: [the log file schema identifier]
Description: [a description of the log file schema]
Reference: [to a specification defining the log file schema]
This document furthermore adds the following two new entries to the
"qlog log file schema URIs" registry:
+======================================+================+===========+
| Log File Schema URI | Description | Reference |
+======================================+================+===========+
| urn:ietf:params:qlog:file:contained | Concrete log | Section 4 |
| | file schema | |
| | that can | |
| | contain | |
| | several | |
| | traces from | |
| | multiple | |
| | vantage | |
| | points. | |
+--------------------------------------+----------------+-----------+
| urn:ietf:params:qlog:file:sequential | Concrete log | Section 5 |
| | file schema | |
| | containing a | |
| | single trace, | |
| | optimized for | |
| | seqential | |
| | read and | |
| | write access. | |
+--------------------------------------+----------------+-----------+
Table 1
IANA is requested to create the "qlog event schema URIs" registry at
https://www.iana.org/assignments/qlog for the purpose of registering
event schema. It has the following format/template:
Marx, et al. Expires 23 April 2026 [Page 50]
Internet-Draft qlog October 2025
Event schema URI: [the event schema identifier]
Namespace: [the identifier of the namespace that this event schema
either defines or extends]
Event Types: [a comma-separated list of concrete event types defined
in the event schema]
Description: [a description of the event schema]
Reference: [to a specification defining the event schema definition]
This document furthermore adds the following two new entries to the
"qlog event schema URIs" registry:
Event schema URI: urn:ietf:params:qlog:events:loglevel
Namespace loglevel
Event Types error,warning,info,debug,verbose
Description: Well-known logging levels for free-form text.
Reference: Section 9.1
Event schema URI: urn:ietf:params:qlog:events:simulation
Namespace simulation
Event Types scenario,marker
Description: Events for simulation testing.
Reference: Section 9.2
16. References
16.1. Normative References
[CDDL] Birkholz, H., Vigano, C., and C. Bormann, "Concise Data
Definition Language (CDDL): A Notational Convention to
Express Concise Binary Object Representation (CBOR) and
JSON Data Structures", RFC 8610, DOI 10.17487/RFC8610,
June 2019, <https://www.rfc-editor.org/rfc/rfc8610>.
Marx, et al. Expires 23 April 2026 [Page 51]
Internet-Draft qlog October 2025
[DNS-PRIVACY]
Dickinson, S., Overeinder, B., van Rijswijk-Deij, R., and
A. Mankin, "Recommendations for DNS Privacy Service
Operators", BCP 232, RFC 8932, DOI 10.17487/RFC8932,
October 2020, <https://www.rfc-editor.org/rfc/rfc8932>.
[I-JSON] Bray, T., Ed., "The I-JSON Message Format", RFC 7493,
DOI 10.17487/RFC7493, March 2015,
<https://www.rfc-editor.org/rfc/rfc7493>.
[JSON] Bray, T., Ed., "The JavaScript Object Notation (JSON) Data
Interchange Format", STD 90, RFC 8259,
DOI 10.17487/RFC8259, December 2017,
<https://www.rfc-editor.org/rfc/rfc8259>.
[JSON-Text-Sequences]
Williams, N., "JavaScript Object Notation (JSON) Text
Sequences", RFC 7464, DOI 10.17487/RFC7464, February 2015,
<https://www.rfc-editor.org/rfc/rfc7464>.
[RFC2046] Freed, N. and N. Borenstein, "Multipurpose Internet Mail
Extensions (MIME) Part Two: Media Types", RFC 2046,
DOI 10.17487/RFC2046, November 1996,
<https://www.rfc-editor.org/rfc/rfc2046>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/rfc/rfc2119>.
[RFC3339] Klyne, G. and C. Newman, "Date and Time on the Internet:
Timestamps", RFC 3339, DOI 10.17487/RFC3339, July 2002,
<https://www.rfc-editor.org/rfc/rfc3339>.
[RFC3553] Mealling, M., Masinter, L., Hardie, T., and G. Klyne, "An
IETF URN Sub-namespace for Registered Protocol
Parameters", BCP 73, RFC 3553, DOI 10.17487/RFC3553, June
2003, <https://www.rfc-editor.org/rfc/rfc3553>.
[RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66,
RFC 3986, DOI 10.17487/RFC3986, January 2005,
<https://www.rfc-editor.org/rfc/rfc3986>.
[RFC6839] Hansen, T. and A. Melnikov, "Additional Media Type
Structured Syntax Suffixes", RFC 6839,
DOI 10.17487/RFC6839, January 2013,
<https://www.rfc-editor.org/rfc/rfc6839>.
Marx, et al. Expires 23 April 2026 [Page 52]
Internet-Draft qlog October 2025
[RFC6973] Cooper, A., Tschofenig, H., Aboba, B., Peterson, J.,
Morris, J., Hansen, M., and R. Smith, "Privacy
Considerations for Internet Protocols", RFC 6973,
DOI 10.17487/RFC6973, July 2013,
<https://www.rfc-editor.org/rfc/rfc6973>.
[RFC7464] Williams, N., "JavaScript Object Notation (JSON) Text
Sequences", RFC 7464, DOI 10.17487/RFC7464, February 2015,
<https://www.rfc-editor.org/rfc/rfc7464>.
[RFC8091] Wilde, E., "A Media Type Structured Syntax Suffix for JSON
Text Sequences", RFC 8091, DOI 10.17487/RFC8091, February
2017, <https://www.rfc-editor.org/rfc/rfc8091>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/rfc/rfc8126>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.
[RFC8259] Bray, T., Ed., "The JavaScript Object Notation (JSON) Data
Interchange Format", STD 90, RFC 8259,
DOI 10.17487/RFC8259, December 2017,
<https://www.rfc-editor.org/rfc/rfc8259>.
[RFC9000] Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
Multiplexed and Secure Transport", RFC 9000,
DOI 10.17487/RFC9000, May 2021,
<https://www.rfc-editor.org/rfc/rfc9000>.
16.2. Informative References
[ANRW-2020]
Marx, R., Piraux, M., Quax, P., and W. Lamotte, "Debugging
QUIC and HTTP/3 with qlog and qvis", September 2020,
<https://qlog.edm.uhasselt.be/anrw/>.
[QLOG-H3] Marx, R., Niccolini, L., Seemann, M., and L. Pardue,
"HTTP/3 qlog event definitions", Work in Progress,
Internet-Draft, draft-ietf-quic-qlog-h3-events-11, 7 July
2025, <https://datatracker.ietf.org/doc/html/draft-ietf-
quic-qlog-h3-events-11>.
Marx, et al. Expires 23 April 2026 [Page 53]
Internet-Draft qlog October 2025
[QLOG-QUIC]
Marx, R., Niccolini, L., Seemann, M., and L. Pardue, "QUIC
event definitions for qlog", Work in Progress, Internet-
Draft, draft-ietf-quic-qlog-quic-events-11, 7 July 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-quic-
qlog-quic-events-11>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/rfc/rfc8446>.
[RFC8546] Trammell, B. and M. Kuehlewind, "The Wire Image of a
Network Protocol", RFC 8546, DOI 10.17487/RFC8546, April
2019, <https://www.rfc-editor.org/rfc/rfc8546>.
Acknowledgements
Much of the initial work by Robin Marx was done at the Hasselt and KU
Leuven Universities.
Thanks to Jana Iyengar, Brian Trammell, Dmitri Tikhonov, Stephen
Petrides, Jari Arkko, Marcus Ihlar, Victor Vasiliev, Mirja
Kuehlewind, Jeremy Laine, Kazu Yamamoto, Christian Huitema, Hugo
Landau, Will Hawkins, Mathis Engelbart, Kazuho Oku, and Jonathan
Lennox for their feedback and suggestions.
Change Log
This section is to be removed before publishing as an RFC.
Since draft-ietf-quic-qlog-main-schema-12:
* Changed Path and related fields to Tuple (#491)
* Replaced all lenght fields with raw.length (#495)
Since draft-ietf-quic-qlog-main-schema-10:
* Multiple editorial changes
* Remove protocol_types and move event_schemas to Trace and TraceSeq
(#449)
Since draft-ietf-quic-qlog-main-schema-09:
* Renamed protocol_type to protocol_types (#427)
* Moved Trigger section. Purely editorial (#430)
Marx, et al. Expires 23 April 2026 [Page 54]
Internet-Draft qlog October 2025
* Removed the concept of categories and updated extension and event
schema logic to match. Major change (#439)
* Reworked completely how we handle timestamps and clocks. Major
change (#433)
Since draft-ietf-quic-qlog-main-schema-08:
* TODO (we forgot...)
Since draft-ietf-quic-qlog-main-schema-07:
* Added path and PathID (#336)
* Removed custom definition of uint64 type (#360, #388)
* ProtocolEventBody is now called ProtocolEventData (#352)
* Editorial changes (#364, #289, #353, #361, #362)
Since draft-ietf-quic-qlog-main-schema-06:
* Editorial reworking of the document (#331, #332)
* Updated IANA considerations section (#333)
Since draft-ietf-quic-qlog-main-schema-05:
* Updated qlog_version to 0.4 (due to breaking changes) (#314)
* Renamed 'transport' category to 'quic' (#302)
* Added 'system_info' field (#305)
* Removed 'summary' and 'configuration' fields (#308)
* Editorial and formatting changes (#298, #303, #304, #316, #320,
#321, #322, #326, #328)
Since draft-ietf-quic-qlog-main-schema-04:
* Updated RawInfo definition and guidance (#243)
Since draft-ietf-quic-qlog-main-schema-03:
* Added security and privacy considerations discussion (#252)
Marx, et al. Expires 23 April 2026 [Page 55]
Internet-Draft qlog October 2025
Since draft-ietf-quic-qlog-main-schema-02:
* No changes - new draft to prevent expiration
Since draft-ietf-quic-qlog-main-schema-01:
* Change the data definition language from TypeScript to CDDL (#143)
Since draft-ietf-quic-qlog-main-schema-00:
* Changed the streaming serialization format from NDJSON to JSON
Text Sequences (#172)
* Added Media Type definitions for various qlog formats (#158)
* Changed to semantic versioning
Since draft-marx-qlog-main-schema-draft-02:
* These changes were done in preparation of the adoption of the
drafts by the QUIC working group (#137)
* Moved RawInfo, Importance, Generic events and Simulation events to
this document.
* Added basic event definition guidelines
* Made protocol_type an array instead of a string (#146)
Since draft-marx-qlog-main-schema-01:
* Decoupled qlog from the JSON format and described a mapping
instead (#89)
- Data types are now specified in this document and proper
definitions for fields were added in this format
- 64-bit numbers can now be either strings or numbers, with a
preference for numbers (#10)
- binary blobs are now logged as lowercase hex strings (#39, #36)
- added guidance to add length-specifiers for binary blobs (#102)
* Removed "time_units" from Configuration. All times are now in ms
instead (#95)
Marx, et al. Expires 23 April 2026 [Page 56]
Internet-Draft qlog October 2025
* Removed the "event_fields" setup for a more straightforward JSON
format (#101,#89)
* Added a streaming option using the NDJSON format (#109,#2,#106)
* Described optional optimization options for implementers (#30)
* Added QLOGDIR and QLOGFILE environment variables, clarified the
.well-known URL usage (#26,#33,#51)
* Overall tightened up the text and added more examples
Since draft-marx-qlog-main-schema-00:
* All field names are now lowercase (e.g., category instead of
CATEGORY)
* Triggers are now properties on the "data" field value, instead of
separate field types (#23)
* group_ids in common_fields is now just also group_id
Authors' Addresses
Robin Marx (editor)
Akamai
Email: rmarx@akamai.com
Luca Niccolini (editor)
Meta
Email: lniccolini@meta.com
Marten Seemann (editor)
Email: martenseemann@gmail.com
Lucas Pardue (editor)
Cloudflare
Email: lucas@lucaspardue.com
Marx, et al. Expires 23 April 2026 [Page 57]