Skip to main content

Remote Attestation Procedures Architecture
draft-ietf-rats-architecture-09

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 9334.
Authors Henk Birkholz , Dave Thaler , Michael Richardson , Ned Smith , Wei Pan
Last updated 2021-02-05
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd (None)
IESG IESG state Became RFC 9334 (Informational)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-rats-architecture-09
RATS Working Group                                           H. Birkholz
Internet-Draft                                            Fraunhofer SIT
Intended status: Informational                                 D. Thaler
Expires: 9 August 2021                                         Microsoft
                                                           M. Richardson
                                                Sandelman Software Works
                                                                N. Smith
                                                                   Intel
                                                                  W. Pan
                                                     Huawei Technologies
                                                         5 February 2021

               Remote Attestation Procedures Architecture
                    draft-ietf-rats-architecture-09

Abstract

   In network protocol exchanges it is often the case that one entity
   requires believable evidence about the operational state of a remote
   peer.  Such evidence is typically conveyed as claims about the peer's
   software and hardware platform, and is subsequently appraised in
   order to assess the peer's trustworthiness.  The process of
   generating and appraising this kind of evidence is known as remote
   attestation.  This document describes an architecture for remote
   attestation procedures that generate, convey, and appraise evidence
   about a peer's operational state.

Note to Readers

   Discussion of this document takes place on the RATS Working Group
   mailing list (rats@ietf.org), which is archived at
   https://mailarchive.ietf.org/arch/browse/rats/
   (https://mailarchive.ietf.org/arch/browse/rats/).

   Source for this draft and an issue tracker can be found at
   https://github.com/ietf-rats-wg/architecture (https://github.com/
   ietf-rats-wg/architecture).

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

Birkholz, et al.          Expires 9 August 2021                 [Page 1]
Internet-Draft              RATS Arch & Terms              February 2021

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 9 August 2021.

Copyright Notice

   Copyright (c) 2021 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Simplified BSD License text
   as described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Reference Use Cases . . . . . . . . . . . . . . . . . . . . .   4
     2.1.  Network Endpoint Assessment . . . . . . . . . . . . . . .   4
     2.2.  Confidential Machine Learning (ML) Model Protection . . .   5
     2.3.  Confidential Data Protection  . . . . . . . . . . . . . .   5
     2.4.  Critical Infrastructure Control . . . . . . . . . . . . .   6
     2.5.  Trusted Execution Environment (TEE) Provisioning  . . . .   6
     2.6.  Hardware Watchdog . . . . . . . . . . . . . . . . . . . .   6
     2.7.  FIDO Biometric Authentication . . . . . . . . . . . . . .   7
   3.  Architectural Overview  . . . . . . . . . . . . . . . . . . .   7
     3.1.  Appraisal Policies  . . . . . . . . . . . . . . . . . . .   9
     3.2.  Reference Values  . . . . . . . . . . . . . . . . . . . .   9
     3.3.  Two Types of Environments of an Attester  . . . . . . . .   9
     3.4.  Layered Attestation Environments  . . . . . . . . . . . .  11
     3.5.  Composite Device  . . . . . . . . . . . . . . . . . . . .  13
     3.6.  Implementation Considerations . . . . . . . . . . . . . .  15
   4.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .  15
     4.1.  Roles . . . . . . . . . . . . . . . . . . . . . . . . . .  15
     4.2.  Artifacts . . . . . . . . . . . . . . . . . . . . . . . .  16
   5.  Topological Patterns  . . . . . . . . . . . . . . . . . . . .  18
     5.1.  Passport Model  . . . . . . . . . . . . . . . . . . . . .  18
     5.2.  Background-Check Model  . . . . . . . . . . . . . . . . .  19
     5.3.  Combinations  . . . . . . . . . . . . . . . . . . . . . .  20
   6.  Roles and Entities  . . . . . . . . . . . . . . . . . . . . .  21
   7.  Trust Model . . . . . . . . . . . . . . . . . . . . . . . . .  22

Birkholz, et al.          Expires 9 August 2021                 [Page 2]
Internet-Draft              RATS Arch & Terms              February 2021

     7.1.  Relying Party . . . . . . . . . . . . . . . . . . . . . .  22
     7.2.  Attester  . . . . . . . . . . . . . . . . . . . . . . . .  23
     7.3.  Relying Party Owner . . . . . . . . . . . . . . . . . . .  23
     7.4.  Verifier  . . . . . . . . . . . . . . . . . . . . . . . .  24
     7.5.  Endorser, Reference Value Provider, and Verifier Owner  .  25
   8.  Conceptual Messages . . . . . . . . . . . . . . . . . . . . .  26
     8.1.  Evidence  . . . . . . . . . . . . . . . . . . . . . . . .  26
     8.2.  Endorsements  . . . . . . . . . . . . . . . . . . . . . .  26
     8.3.  Attestation Results . . . . . . . . . . . . . . . . . . .  27
   9.  Claims Encoding Formats . . . . . . . . . . . . . . . . . . .  28
   10. Freshness . . . . . . . . . . . . . . . . . . . . . . . . . .  29
     10.1.  Explicit Timekeeping using Synchronized Clocks . . . . .  30
     10.2.  Implicit Timekeeping using Nonces  . . . . . . . . . . .  30
     10.3.  Implicit Timekeeping using Epoch Handles . . . . . . . .  30
     10.4.  Discussion . . . . . . . . . . . . . . . . . . . . . . .  31
   11. Privacy Considerations  . . . . . . . . . . . . . . . . . . .  32
   12. Security Considerations . . . . . . . . . . . . . . . . . . .  33
     12.1.  Attester and Attestation Key Protection  . . . . . . . .  33
       12.1.1.  On-Device Attester and Key Protection  . . . . . . .  33
       12.1.2.  Attestation Key Provisioning Processes . . . . . . .  34
     12.2.  Integrity Protection . . . . . . . . . . . . . . . . . .  35
     12.3.  Handle-based Attestation . . . . . . . . . . . . . . . .  36
   13. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  36
   14. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  37
   15. Notable Contributions . . . . . . . . . . . . . . . . . . . .  37
   16. Appendix A: Time Considerations . . . . . . . . . . . . . . .  37
     16.1.  Example 1: Timestamp-based Passport Model Example  . . .  38
     16.2.  Example 2: Nonce-based Passport Model Example  . . . . .  40
     16.3.  Example 3: Handle-based Passport Model Example . . . . .  42
     16.4.  Example 4: Timestamp-based Background-Check Model
            Example  . . . . . . . . . . . . . . . . . . . . . . . .  43
     16.5.  Example 5: Nonce-based Background-Check Model Example  .  44
   17. References  . . . . . . . . . . . . . . . . . . . . . . . . .  45
     17.1.  Normative References . . . . . . . . . . . . . . . . . .  45
     17.2.  Informative References . . . . . . . . . . . . . . . . .  45
   Contributors  . . . . . . . . . . . . . . . . . . . . . . . . . .  47
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  48

1.  Introduction

   In Remote Attestation Procedures (RATS), one peer (the "Attester")
   produces believable information about itself - Evidence - to enable a
   remote peer (the "Relying Party") to decide whether to consider that
   Attester a trustworthy peer or not.  RATS are facilitated by an
   additional vital party, the Verifier.

Birkholz, et al.          Expires 9 August 2021                 [Page 3]
Internet-Draft              RATS Arch & Terms              February 2021

   The Verifier appraises Evidence via appraisal policies and creates
   the Attestation Results to support Relying Parties in their decision
   process.  This document defines a flexible architecture consisting of
   attestation roles and their interactions via conceptual messages.
   Additionally, this document defines a universal set of terms that can
   be mapped to various existing and emerging Remote Attestation
   Procedures.  Common topological models and the data flows associated
   with them, such as the "Passport Model" and the "Background-Check
   Model" are illustrated.  The purpose is to define useful terminology
   for attestation and enable readers to map their solution architecture
   to the canonical attestation architecture provided here.  Having a
   common terminology that provides well-understood meanings for common
   themes such as roles, device composition, topological models, and
   appraisal is vital for semantic interoperability across solutions and
   platforms involving multiple vendors and providers.

   Amongst other things, this document is about trust and
   trustworthiness.  Trust is a choice one makes about another system.
   Trustworthiness is a quality about the other system that can be used
   in making one's decision to trust it or not.  This is subtle
   difference and being familiar with the difference is crucial for
   using this document.  Additionally, the concepts of freshness and
   trust relationships with respect to RATS are elaborated on to enable
   implementers to choose appropriate solutions to compose their Remote
   Attestation Procedures.

2.  Reference Use Cases

   This section covers a number of representative use cases for remote
   attestation, independent of specific solutions.  The purpose is to
   provide motivation for various aspects of the architecture presented
   in this draft.  Many other use cases exist, and this document does
   not intend to have a complete list, only to have a set of use cases
   that collectively cover all the functionality required in the
   architecture.

   Each use case includes a description followed by a summary of the
   Attester and Relying Party roles.

2.1.  Network Endpoint Assessment

   Network operators want a trustworthy report that includes identity
   and version information about the hardware and software on the
   machines attached to their network, for purposes such as inventory,
   audit, anomaly detection, record maintenance and/or trending reports
   (logging).  The network operator may also want a policy by which full
   access is only granted to devices that meet some definition of
   hygiene, and so wants to get claims about such information and verify

Birkholz, et al.          Expires 9 August 2021                 [Page 4]
Internet-Draft              RATS Arch & Terms              February 2021

   its validity.  Remote attestation is desired to prevent vulnerable or
   compromised devices from getting access to the network and
   potentially harming others.

   Typically, solutions start with a specific component (called a "root
   of trust") that provides device identity and protected storage for
   measurements.  The system components perform a series of measurements
   that may be signed by the root of trust, considered as Evidence about
   the hardware, firmware, BIOS, software, etc. that is present.

   Attester:  A device desiring access to a network

   Relying Party:  Network equipment such as a router, switch, or access
      point, responsible for admission of the device into the network

2.2.  Confidential Machine Learning (ML) Model Protection

   A device manufacturer wants to protect its intellectual property.
   This is primarily the ML model it developed and runs in the devices
   purchased by its customers.  The goals for the protection include
   preventing attackers, potentially the customer themselves, from
   seeing the details of the model.

   This typically works by having some protected environment in the
   device go through a remote attestation with some manufacturer service
   that can assess its trustworthiness.  If remote attestation succeeds,
   then the manufacturer service releases either the model, or a key to
   decrypt a model the Attester already has in encrypted form, to the
   requester.

   Attester:  A device desiring to run an ML model

   Relying Party:  A server or service holding ML models it desires to
      protect

2.3.  Confidential Data Protection

   This is a generalization of the ML model use case above, where the
   data can be any highly confidential data, such as health data about
   customers, payroll data about employees, future business plans, etc.
   As part of the attestation procedure, an assessment is made against a
   set of policies to evaluate the state of the system that is
   requesting the confidential data.  Attestation is desired to prevent
   leaking data to compromised devices.

   Attester:  An entity desiring to retrieve confidential data

   Relying Party:  An entity that holds confidential data for release to

Birkholz, et al.          Expires 9 August 2021                 [Page 5]
Internet-Draft              RATS Arch & Terms              February 2021

      authorized entities

2.4.  Critical Infrastructure Control

   In this use case, potentially harmful physical equipment (e.g., power
   grid, traffic control, hazardous chemical processing, etc.) is
   connected to a network.  The organization managing such
   infrastructure needs to ensure that only authorized code and users
   can control such processes, and that these processes are protected
   from unauthorized manipulation or other threats.  When a protocol
   operation can affect a component of a critical system, the device
   attached to the critical equipment requires some assurances depending
   on the security context, including that: the requesting device or
   application has not been compromised, and the requesters and actors
   act on applicable policies, As such, remote attestation can be used
   to only accept commands from requesters that are within policy.

   Attester:  A device or application wishing to control physical
      equipment

   Relying Party:  A device or application connected to potentially
      dangerous physical equipment (hazardous chemical processing,
      traffic control, power grid, etc.)

2.5.  Trusted Execution Environment (TEE) Provisioning

   A "Trusted Application Manager (TAM)" server is responsible for
   managing the applications running in the TEE of a client device.  To
   do this, the TAM wants to assess the state of a TEE, or of
   applications in the TEE, of a client device.  The TEE conducts a
   remote attestation procedure with the TAM, which can then decide
   whether the TEE is already in compliance with the TAM's latest
   policy, or if the TAM needs to uninstall, update, or install approved
   applications in the TEE to bring it back into compliance with the
   TAM's policy.

   Attester:  A device with a trusted execution environment capable of
      running trusted applications that can be updated

   Relying Party:  A Trusted Application Manager

2.6.  Hardware Watchdog

   There is a class of malware that holds a device hostage and does not
   allow it to reboot to prevent updates from being applied.  This can
   be a significant problem, because it allows a fleet of devices to be
   held hostage for ransom.

Birkholz, et al.          Expires 9 August 2021                 [Page 6]
Internet-Draft              RATS Arch & Terms              February 2021

   A solution to this problem is a watchdog timer implemented in a
   protected environment such as a Trusted Platform Module (TPM), as
   described in [TCGarch] section 43.3.  If the watchdog does not
   receive regular, and fresh, Attestation Results as to the system's
   health, then it forces a reboot.

   Attester:  The device that should be protected from being held
      hostage for a long period of time

   Relying Party:  A watchdog capable of triggering a procedure that
      resets a device into a known, good operational state.

2.7.  FIDO Biometric Authentication

   In the Fast IDentity Online (FIDO) protocol [WebAuthN], [CTAP], the
   device in the user's hand authenticates the human user, whether by
   biometrics (such as fingerprints), or by PIN and password.  FIDO
   authentication puts a large amount of trust in the device compared to
   typical password authentication because it is the device that
   verifies the biometric, PIN and password inputs from the user, not
   the server.  For the Relying Party to know that the authentication is
   trustworthy, the Relying Party needs to know that the Authenticator
   part of the device is trustworthy.  The FIDO protocol employs remote
   attestation for this.

   The FIDO protocol supports several remote attestation protocols and a
   mechanism by which new ones can be registered and added.  Remote
   attestation defined by RATS is thus a candidate for use in the FIDO
   protocol.

   Other biometric authentication protocols such as the Chinese IFAA
   standard and WeChat Pay as well as Google Pay make use of attestation
   in one form or another.

   Attester:  Every FIDO Authenticator contains an Attester.

   Relying Party:  Any web site, mobile application back-end, or service
      that relies on authentication data based on biometric information.

3.  Architectural Overview

   Figure 1 depicts the data that flows between different roles,
   independent of protocol or use case.

Birkholz, et al.          Expires 9 August 2021                 [Page 7]
Internet-Draft              RATS Arch & Terms              February 2021

    ************   *************    ************    *****************
    * Endorser *   * Reference *    * Verifier *    * Relying Party *
    ************   * Value     *    *  Owner   *    *  Owner        *
       |           * Provider  *    ************    *****************
       |           *************          |                 |
       |                  |               |                 |
       |Endorsements      |Reference      |Appraisal        |Appraisal
       |                  |Values         |Policy           |Policy for
       |                  |               |for              |Attestation
       .-----------.      |               |Evidence         |Results
                   |      |               |                 |
                   |      |               |                 |
                   v      v               v                 |
                 .---------------------------.              |
          .----->|          Verifier         |------.       |
          |      '---------------------------'      |       |
          |                                         |       |
          |                              Attestation|       |
          |                              Results    |       |
          | Evidence                                |       |
          |                                         |       |
          |                                         v       v
    .----------.                                .---------------.
    | Attester |                                | Relying Party |
    '----------'                                '---------------'

                      Figure 1: Conceptual Data Flow

   An Attester creates Evidence that is conveyed to a Verifier.

   The Verifier uses the Evidence, any Reference Values from Reference
   Value Providers, and any Endorsements from Endorsers, by applying an
   Appraisal Policy for Evidence to assess the trustworthiness of the
   Attester, and generates Attestation Results for use by Relying
   Parties.  The Appraisal Policy for Evidence might be obtained from an
   Endorser along with the Endorsements, and/or might be obtained via
   some other mechanism such as being configured in the Verifier by the
   Verifier Owner.

   The Relying Party uses Attestation Results by applying its own
   appraisal policy to make application-specific decisions such as
   authorization decisions.  The Appraisal Policy for Attestation
   Results is configured in the Relying Party by the Relying Party
   Owner, and/or is programmed into the Relying Party.

Birkholz, et al.          Expires 9 August 2021                 [Page 8]
Internet-Draft              RATS Arch & Terms              February 2021

3.1.  Appraisal Policies

   The Verifier, when appraising Evidence, or the Relying Party, when
   appraising Attestation Results, checks the values of some claims
   against constraints specified in its appraisal policy.  Such
   constraints might involve a comparison for equality against a
   Reference Value, or a check for being in a range bounded by Reference
   Values, or membership in a set of Reference Values, or a check
   against values in other claims, or any other test.

3.2.  Reference Values

   Reference Values used in appraisal come from a Reference Value
   Provider and are then used by the appraisal policy.  They might be
   conveyed in any number of ways, including: * as part of the appraisal
   policy itself, if the Verifier Owner either: acquires Reference
   Values from a Reference Value Provider or is itself a Reference Value
   Provider; * as part of an Endorsement, if the Endorser either
   acquires Reference Values from a Reference Value Provider or is
   itself a Reference Value Provider; or * via separate communication.

   The actual data format and semantics of any Reference Values are
   specific to claims and implementations.  This architecture document
   does not define any general purpose format for them or general means
   for comparison.

3.3.  Two Types of Environments of an Attester

   As shown in Figure 2, an Attester consists of at least one Attesting
   Environment and at least one Target Environment.  In some
   implementations, the Attesting and Target Environments might be
   combined.  Other implementations might have multiple Attesting and
   Target Environments, such as in the examples described in more detail
   in Section 3.4 and Section 3.5.  Other examples may exist.  Besides,
   the examples discussed could be combined into even more complex
   implementations.

Birkholz, et al.          Expires 9 August 2021                 [Page 9]
Internet-Draft              RATS Arch & Terms              February 2021

                    .--------------------------------.
                    |                                |
                    |            Verifier            |
                    |                                |
                    '--------------------------------'
                                            ^
                                            |
                  .-------------------------|----------.
                  |                         |          |
                  |   .----------------.    |          |
                  |   | Target         |    |          |
                  |   | Environment    |    |          |
                  |   |                |    | Evidence |
                  |   '----------------'    |          |
                  |                   |     |          |
                  |                   |     |          |
                  |          Collect  |     |          |
                  |           Claims  |     |          |
                  |                   |     |          |
                  |                   v     |          |
                  |                 .-------------.    |
                  |                 | Attesting   |    |
                  |                 | Environment |    |
                  |                 |             |    |
                  |                 '-------------'    |
                  |               Attester             |
                  '------------------------------------'

                    Figure 2: Two Types of Environments

   Claims are collected from Target Environments.  That is, Attesting
   Environments collect the values and the information to be represented
   in Claims, by reading system registers and variables, calling into
   subsystems, taking measurements on code, memory, or other security
   related assets of the Target Environment.  Attesting Environments
   then format the claims appropriately, and typically use key material
   and cryptographic functions, such as signing or cipher algorithms, to
   create Evidence.  There is no limit to or requirement on the types of
   hardware or software environments that can be used to implement an
   Attesting Environment, for example: Trusted Execution Environments
   (TEEs), embedded Secure Elements (eSEs), Trusted Platform Modules
   (TPMs), or BIOS firmware.

   An arbitrary execution environment may not, by default, be capable of
   claims collection for a given Target Environment.  Execution
   environments that are designed specifically to be capable of claims
   collection are referred to in this document as Attesting
   Environments.  For example, a TPM doesn't actively collect claims

Birkholz, et al.          Expires 9 August 2021                [Page 10]
Internet-Draft              RATS Arch & Terms              February 2021

   itself, it instead requires another component to feed various values
   to the TPM.  Thus, an Attesting Environment in such a case would be
   the combination of the TPM together with whatever component is
   feeding it the measurements.

3.4.  Layered Attestation Environments

   By definition, the Attester role generates Evidence.  An Attester may
   consist of one or more nested environments (layers).  The root layer
   of an Attester includes at least one root of trust.  In order to
   appraise Evidence generated by an Attester, the Verifier needs to
   trust the Attester's root of trust.  Trust in the Attester's root of
   trust can be established either directly (e.g., the Verifier puts the
   root of trust's public key into its trust anchor store) or
   transitively via an Endorser (e.g., the Verifier puts the Endorser's
   public key into its trust anchor store).  In layered attestation, a
   root of trust is the initial Attesting Environment.  Claims can be
   collected from or about each layer.  The corresponding Claims can be
   structured in a nested fashion that reflects the nesting of the
   Attester's layers.  Normally, Claims are not self-asserted, rather a
   previous layer acts as the Attesting Environment for the next layer.
   Claims about a root of trust typically are asserted by Endorsers.

   The device illustrated in Figure 3 includes (A) a BIOS stored in
   read-only memory, (B) an updatable bootloader, and (C) an operating
   system kernel.

Birkholz, et al.          Expires 9 August 2021                [Page 11]
Internet-Draft              RATS Arch & Terms              February 2021

               .----------.                    .----------.
               |          |                    |          |
               | Endorser |------------------->| Verifier |
               |          |    Endorsements    |          |
               '----------'  for A, B, and C   '----------'
                                                     ^
           .------------------------------------.    |
           |                                    |    |
           |   .---------------------------.    |    |
           |   | Target                    |    |    | Layered
           |   | Environment               |    |    | Evidence
           |   | C                         |    |    |   for
           |   '---------------------------'    |    | B and C
           |           Collect |                |    |
           |           claims  |                |    |
           |   .---------------|-----------.    |    |
           |   | Target        v           |    |    |
           |   | Environment .-----------. |    |    |
           |   | B           | Attesting | |    |    |
           |   |             |Environment|-----------'
           |   |             |     B     | |    |
           |   |             '-----------' |    |
           |   |                     ^     |    |
           |   '---------------------|-----'    |
           |           Collect |     | Evidence |
           |           claims  v     |  for B   |
           |                 .-----------.      |
           |                 | Attesting |      |
           |                 |Environment|      |
           |                 |     A     |      |
           |                 '-----------'      |
           |                                    |
           '------------------------------------'

                         Figure 3: Layered Attester

   Attesting Environment A, the read-only BIOS in this example, has to
   ensure the integrity of the bootloader (Target Environment B).  There
   are potentially multiple kernels to boot, and the decision is up to
   the bootloader.  Only a bootloader with intact integrity will make an
   appropriate decision.  Therefore, the Claims relating to the
   integrity of the bootloader have to be measured securely.  At this
   stage of the boot-cycle of the device, the Claims collected typically
   cannot be composed into Evidence.

   After the boot sequence is started, the BIOS conducts the most
   important and defining feature of layered attestation, which is that
   the successfully measured Target Environment B now becomes (or

Birkholz, et al.          Expires 9 August 2021                [Page 12]
Internet-Draft              RATS Arch & Terms              February 2021

   contains) an Attesting Environment for the next layer.  This
   procedure in Layered Attestation is sometimes called "staging".  It
   is important that the new Attesting Environment B not be able to
   alter any Claims about its own Target Environment B.  This can be
   ensured having those Claims be either signed by Attesting Environment
   A or stored in an untamperable manner by Attesting Environment A.

   Continuing with this example, the bootloader's Attesting Environment
   B is now in charge of collecting Claims about Target Environment C,
   which in this example is the kernel to be booted.  The final Evidence
   thus contains two sets of Claims: one set about the bootloader as
   measured and signed by the BIOS, plus a set of Claims about the
   kernel as measured and signed by the bootloader.

   This example could be extended further by making the kernel become
   another Attesting Environment for an application as another Target
   Environment.  This would result in a third set of Claims in the
   Evidence pertaining to that application.

   The essence of this example is a cascade of staged environments.
   Each environment has the responsibility of measuring the next
   environment before the next environment is started.  In general, the
   number of layers may vary by device or implementation, and an
   Attesting Environment might even have multiple Target Environments
   that it measures, rather than only one as shown in Figure 3.

3.5.  Composite Device

   A Composite Device is an entity composed of multiple sub-entities
   such that its trustworthiness has to be determined by the appraisal
   of all these sub-entities.

   Each sub-entity has at least one Attesting Environment collecting the
   claims from at least one Target Environment, then this sub-entity
   generates Evidence about its trustworthiness.  Therefore each sub-
   entity can be called an Attester.  Among all the Attesters, there may
   be only some which have the ability to communicate with the Verifier
   while others do not.

   For example, a carrier-grade router consists of a chassis and
   multiple slots.  The trustworthiness of the router depends on all its
   slots' trustworthiness.  Each slot has an Attesting Environment such
   as a TEE collecting the claims of its boot process, after which it
   generates Evidence from the claims.  Among these slots, only a main
   slot can communicate with the Verifier while other slots cannot.  But
   other slots can communicate with the main slot by the links between
   them inside the router.  So the main slot collects the Evidence of
   other slots, produces the final Evidence of the whole router and

Birkholz, et al.          Expires 9 August 2021                [Page 13]
Internet-Draft              RATS Arch & Terms              February 2021

   conveys the final Evidence to the Verifier.  Therefore the router is
   a Composite Device, each slot is an Attester, and the main slot is
   the lead Attester.

   Another example is a multi-chassis router composed of multiple single
   carrier-grade routers.  The multi-chassis router provides higher
   throughput by interconnecting multiple routers and can be logically
   treated as one router for simpler management.  A multi-chassis router
   provides a management point that connects to the Verifier.  Other
   routers are only connected to the main router by the network cables,
   and therefore they are managed and appraised via this main router's
   help.  So, in this case, the multi-chassis router is the Composite
   Device, each router is an Attester and the main router is the lead
   Attester.

   Figure 4 depicts the conceptual data flow for a Composite Device.

                      .-----------------------------.
                      |           Verifier          |
                      '-----------------------------'
                                      ^
                                      |
                                      | Evidence of
                                      | Composite Device
                                      |
   .----------------------------------|-------------------------------.
   | .--------------------------------|-----.      .------------.     |
   | |  Collect             .------------.  |      |            |     |
   | |  Claims   .--------->|  Attesting |<--------| Attester B |-.   |
   | |           |          |Environment |  |      '------------. |   |
   | |  .----------------.  |            |<----------| Attester C |-. |
   | |  |     Target     |  |            |  |        '------------' | |
   | |  | Environment(s) |  |            |<------------| ...        | |
   | |  |                |  '------------'  | Evidence '------------' |
   | |  '----------------'                  |    of                   |
   | |                                      | Attesters               |
   | | lead Attester A                      | (via Internal Links or  |
   | '--------------------------------------' Network Connections)    |
   |                                                                  |
   |                       Composite Device                           |
   '------------------------------------------------------------------'

                         Figure 4: Composite Device

   In the Composite Device, each Attester generates its own Evidence by
   its Attesting Environment(s) collecting the claims from its Target
   Environment(s).  The lead Attester collects the Evidence from the
   other Attesters and conveys it to a Verifier.  Collection of Evidence

Birkholz, et al.          Expires 9 August 2021                [Page 14]
Internet-Draft              RATS Arch & Terms              February 2021

   from sub-entities may itself be a form of Claims collection that
   results in Evidence asserted by the lead Attester.  The lead Attester
   generates the Evidence about the layout of the Composite Device,
   while sub-Attesters generate Evidence about their respective modules.

   In this situation, the trust model described in Section 7 is also
   suitable for this inside Verifier.

3.6.  Implementation Considerations

   An entity can take on multiple RATS roles (e.g., Attester, Verifier,
   Relying Party, etc.) at the same time.  Multiple entities can
   cooperate to implement a single RATS role as well.  The combination
   of roles and entities can be arbitrary.  For example, in the
   Composite Device scenario, the entity inside the lead Attester can
   also take on the role of a Verifier, and the outer entity of Verifier
   can take on the role of a Relying Party.  After collecting the
   Evidence of other Attesters, this inside Verifier uses Endorsements
   and appraisal policies (obtained the same way as any other Verifier)
   in the verification process to generate Attestation Results.  The
   inside Verifier then conveys the Attestation Results of other
   Attesters to the outside Verifier, whether in the same conveyance
   protocol as the Evidence or not.

4.  Terminology

   This document uses the following terms.

4.1.  Roles

   Attester:  A role performed by an entity (typically a device) whose
      Evidence must be appraised in order to infer the extent to which
      the Attester is considered trustworthy, such as when deciding
      whether it is authorized to perform some operation.

      Produces: Evidence

   Relying Party:  A role performed by an entity that depends on the
      validity of information about an Attester, for purposes of
      reliably applying application specific actions.  Compare /relying
      party/ in [RFC4949].

      Consumes: Attestation Results

   Verifier:  A role performed by an entity that appraises the validity
      of Evidence about an Attester and produces Attestation Results to
      be used by a Relying Party.

Birkholz, et al.          Expires 9 August 2021                [Page 15]
Internet-Draft              RATS Arch & Terms              February 2021

      Consumes: Evidence, Reference Values, Endorsements, Appraisal
      Policy for Evidence

      Produces: Attestation Results

   Relying Party Owner:  A role performed by an entity (typically an
      administrator), that is authorized to configure Appraisal Policy
      for Attestation Results in a Relying Party.

      Produces: Appraisal Policy for Attestation Results

   Verifier Owner:  A role performed by an entity (typically an
      administrator), that is authorized to configure Appraisal Policy
      for Evidence in a Verifier.

      Produces: Appraisal Policy for Evidence

   Endorser:  A role performed by an entity (typically a manufacturer)
      whose Endorsements help Verifiers appraise the authenticity of
      Evidence.

      Produces: Endorsements

   Reference Value Provider:  A role performed by an entity (typically a
      manufacturer) whose Reference Values help Verifiers appraise
      Evidence to determine if acceptable known Claims have been
      recorded by the Attester.

      Produces: Reference Values

4.2.  Artifacts

   Claim:  A piece of asserted information, often in the form of a name/
      value pair.  Claims make up the usual structure of Evidence and
      other RATS artifacts.  Compare /claim/ in [RFC7519].

   Endorsement:  A secure statement that an Endorser vouches for the
      integrity of an Attester's various capabilities such as Claims
      collection and Evidence signing.

      Consumed By: Verifier

      Produced By: Endorser

   Evidence:  A set of Claims generated by an Attester to be appraised
      by a Verifier.  Evidence may include configuration data,
      measurements, telemetry, or inferences.

Birkholz, et al.          Expires 9 August 2021                [Page 16]
Internet-Draft              RATS Arch & Terms              February 2021

      Consumed By: Verifier

      Produced By: Attester

   Attestation Result:  The output generated by a Verifier, typically
      including information about an Attester, where the Verifier
      vouches for the validity of the results.

      Consumed By: Relying Party

      Produced By: Verifier

   Appraisal Policy for Evidence:  A set of rules that informs how a
      Verifier evaluates the validity of information about an Attester.
      Compare /security policy/ in [RFC4949].

      Consumed By: Verifier

      Produced By: Verifier Owner

   Appraisal Policy for Attestation Results:  A set of rules that direct
      how a Relying Party uses the Attestation Results regarding an
      Attester generated by the Verifiers.  Compare /security policy/ in
      [RFC4949].

      Consumed by: Relying Party

      Produced by: Relying Party Owner

   Reference Values:  A set of values against which values of Claims can
      be compared as part of applying an Appraisal Policy for Evidence.
      Reference Values are sometimes referred to in other documents as
      known-good values, golden measurements, or nominal values,
      although those terms typically assume comparison for equality,
      whereas here Reference Values might be more general and be used in
      any sort of comparison.

      Consumed By: Verifier

      Produced By: Reference Value Provider

Birkholz, et al.          Expires 9 August 2021                [Page 17]
Internet-Draft              RATS Arch & Terms              February 2021

5.  Topological Patterns

   Figure 1 shows a data-flow diagram for communication between an
   Attester, a Verifier, and a Relying Party.  The Attester conveys its
   Evidence to the Verifier for appraisal, and the Relying Party gets
   the Attestation Result from the Verifier.  This section refines it by
   describing two reference models, as well as one example composition
   thereof.  The discussion that follows is for illustrative purposes
   only and does not constrain the interactions between RATS roles to
   the presented patterns.

5.1.  Passport Model

   The passport model is so named because of its resemblance to how
   nations issue passports to their citizens.  The nature of the
   Evidence that an individual needs to provide to its local authority
   is specific to the country involved.  The citizen retains control of
   the resulting passport document and presents it to other entities
   when it needs to assert a citizenship or identity claim, such as an
   airport immigration desk.  The passport is considered sufficient
   because it vouches for the citizenship and identity claims, and it is
   issued by a trusted authority.  Thus, in this immigration desk
   analogy, the passport issuing agency is a Verifier, the passport is
   an Attestation Result, and the immigration desk is a Relying Party.

   In this model, an Attester conveys Evidence to a Verifier, which
   compares the Evidence against its appraisal policy.  The Verifier
   then gives back an Attestation Result.  If the Attestation Result was
   a successful one, the Attester can then present the Attestation
   Result (and possibly additional Claims) to a Relying Party, which
   then compares this information against its own appraisal policy.

   Three ways in which the process may fail include:

   *  First, the Verifier may not issue a positive Attestation Result
      due to the Evidence not passing the Appraisal Policy for Evidence.

   *  The second way in which the process may fail is when the
      Attestation Result is examined by the Relying Party, and based
      upon the Appraisal Policy for Attestation Results, the result does
      not pass the policy.

   *  The third way is when the Verifier is unreachable or unavailable.

Birkholz, et al.          Expires 9 August 2021                [Page 18]
Internet-Draft              RATS Arch & Terms              February 2021

   Since the resource access protocol between the Attester and Relying
   Party includes an Attestation Result, in this model the details of
   that protocol constrain the serialization format of the Attestation
   Result.  The format of the Evidence on the other hand is only
   constrained by the Attester-Verifier remote attestation protocol.

         +-------------+
         |             | Compare Evidence
         |   Verifier  | against appraisal policy
         |             |
         +-------------+
              ^    |
      Evidence|    |Attestation
              |    |  Result
              |    v
         +----------+              +---------+
         |          |------------->|         |Compare Attestation
         | Attester | Attestation  | Relying | Result against
         |          |    Result    |  Party  | appraisal
         +----------+              +---------+  policy

                          Figure 5: Passport Model

5.2.  Background-Check Model

   The background-check model is so named because of the resemblance of
   how employers and volunteer organizations perform background checks.
   When a prospective employee provides claims about education or
   previous experience, the employer will contact the respective
   institutions or former employers to validate the claim.  Volunteer
   organizations often perform police background checks on volunteers in
   order to determine the volunteer's trustworthiness.  Thus, in this
   analogy, a prospective volunteer is an Attester, the organization is
   the Relying Party, and the organization that issues a report is a
   Verifier.

   In this model, an Attester conveys Evidence to a Relying Party, which
   simply passes it on to a Verifier.  The Verifier then compares the
   Evidence against its appraisal policy, and returns an Attestation
   Result to the Relying Party.  The Relying Party then compares the
   Attestation Result against its own appraisal policy.

Birkholz, et al.          Expires 9 August 2021                [Page 19]
Internet-Draft              RATS Arch & Terms              February 2021

   The resource access protocol between the Attester and Relying Party
   includes Evidence rather than an Attestation Result, but that
   Evidence is not processed by the Relying Party.  Since the Evidence
   is merely forwarded on to a trusted Verifier, any serialization
   format can be used for Evidence because the Relying Party does not
   need a parser for it.  The only requirement is that the Evidence can
   be _encapsulated in_ the format required by the resource access
   protocol between the Attester and Relying Party.

   However, like in the Passport model, an Attestation Result is still
   consumed by the Relying Party.  Code footprint and attack surface
   area can be minimized by using a serialization format for which the
   Relying Party already needs a parser to support the protocol between
   the Attester and Relying Party, which may be an existing standard or
   widely deployed resource access protocol.  Such minimization is
   especially important if the Relying Party is a constrained node.

                                  +-------------+
                                  |             | Compare Evidence
                                  |   Verifier  | against appraisal
                                  |             | policy
                                  +-------------+
                                       ^    |
                               Evidence|    |Attestation
                                       |    |  Result
                                       |    v
      +------------+               +-------------+
      |            |-------------->|             | Compare Attestation
      |   Attester |   Evidence    |   Relying   | Result against
      |            |               |    Party    | appraisal policy
      +------------+               +-------------+

                      Figure 6: Background-Check Model

5.3.  Combinations

   One variation of the background-check model is where the Relying
   Party and the Verifier are on the same machine, performing both
   functions together.  In this case, there is no need for a protocol
   between the two.

   It is also worth pointing out that the choice of model depends on the
   use case, and that different Relying Parties may use different
   topological patterns.

   The same device may need to create Evidence for different Relying
   Parties and/or different use cases.  For instance, it would use one
   model to provide Evidence to a network infrastructure device to gain

Birkholz, et al.          Expires 9 August 2021                [Page 20]
Internet-Draft              RATS Arch & Terms              February 2021

   access to the network, and the other model to provide Evidence to a
   server holding confidential data to gain access to that data.  As
   such, both models may simultaneously be in use by the same device.

   Figure 7 shows another example of a combination where Relying Party 1
   uses the passport model, whereas Relying Party 2 uses an extension of
   the background-check model.  Specifically, in addition to the basic
   functionality shown in Figure 6, Relying Party 2 actually provides
   the Attestation Result back to the Attester, allowing the Attester to
   use it with other Relying Parties.  This is the model that the
   Trusted Application Manager plans to support in the TEEP architecture
   [I-D.ietf-teep-architecture].

         +-------------+
         |             | Compare Evidence
         |   Verifier  | against appraisal policy
         |             |
         +-------------+
              ^    |
      Evidence|    |Attestation
              |    |  Result
              |    v
         +-------------+
         |             | Compare
         |   Relying   | Attestation Result
         |   Party 2   | against appraisal policy
         +-------------+
              ^    |
      Evidence|    |Attestation
              |    |  Result
              |    v
         +----------+               +----------+
         |          |-------------->|          | Compare Attestation
         | Attester |  Attestation  |  Relying | Result against
         |          |     Result    |  Party 1 | appraisal policy
         +----------+               +----------+

                       Figure 7: Example Combination

6.  Roles and Entities

   An entity in the RATS architecture includes at least one of the roles
   defined in this document.  An entity can aggregate more than one role
   into itself.  These collapsed roles combine the duties of multiple
   roles.

Birkholz, et al.          Expires 9 August 2021                [Page 21]
Internet-Draft              RATS Arch & Terms              February 2021

   In these cases, interaction between these roles do not necessarily
   use the Internet Protocol.  They can be using a loopback device or
   other IP-based communication between separate environments, but they
   do not have to.  Alternative channels to convey conceptual messages
   include function calls, sockets, GPIO interfaces, local busses, or
   hypervisor calls.  This type of conveyance is typically found in
   Composite Devices.  Most importantly, these conveyance methods are
   out-of-scope of RATS, but they are presumed to exist in order to
   convey conceptual messages appropriately between roles.

   For example, an entity that both connects to a wide-area network and
   to a system bus is taking on both the Attester and Verifier roles.
   As a system bus-connected entity, a Verifier consumes Evidence from
   other devices connected to the system bus that implement Attester
   roles.  As a wide-area network connected entity, it may implement an
   Attester role.

   In essence, an entity that combines more than one role creates and
   consumes the corresponding conceptual messages as defined in this
   document.

7.  Trust Model

7.1.  Relying Party

   This document covers scenarios for which a Relying Party trusts a
   Verifier that can appraise the trustworthiness of information about
   an Attester.  Such trust might come by the Relying Party trusting the
   Verifier (or its public key) directly, or might come by trusting an
   entity (e.g., a Certificate Authority) that is in the Verifier's
   certificate chain.

   The Relying Party might implicitly trust a Verifier, such as in a
   Verifier/Relying Party combination where the Verifier and Relying
   Party roles are combined.  Or, for a stronger level of security, the
   Relying Party might require that the Verifier first provide
   information about itself that the Relying Party can use to assess the
   trustworthiness of the Verifier before accepting its Attestation
   Results.

   For example, one explicit way for a Relying Party "A" to establish
   such trust in a Verifier "B", would be for B to first act as an
   Attester where A acts as a combined Verifier/Relying Party.  If A
   then accepts B as trustworthy, it can choose to accept B as a
   Verifier for other Attesters.

Birkholz, et al.          Expires 9 August 2021                [Page 22]
Internet-Draft              RATS Arch & Terms              February 2021

   As another example, the Relying Party can establish trust in the
   Verifier by out of band establishment of key material, combined with
   a protocol like TLS to communicate.  There is an assumption that
   between the establishment of the trusted key material and the
   creation of the Evidence, that the Verifier has not been compromised.

   Similarly, the Relying Party also needs to trust the Relying Party
   Owner for providing its Appraisal Policy for Attestation Results, and
   in some scenarios the Relying Party might even require that the
   Relying Party Owner go through a remote attestation procedure with it
   before the Relying Party will accept an updated policy.  This can be
   done similarly to how a Relying Party could establish trust in a
   Verifier as discussed above.

7.2.  Attester

   In some scenarios, Evidence might contain sensitive information such
   as Personally Identifiable Information (PII) or system identifiable
   information.  Thus, an Attester must trust entities to which it
   conveys Evidence, to not reveal sensitive data to unauthorized
   parties.  The Verifier might share this information with other
   authorized parties, according to a governing policy that address the
   handling of sensitive information (potentially included in Appraisal
   Policies for Evidence).  In the background-check model, this Evidence
   may also be revealed to Relying Party(s).

   When Evidence contains sensitive information, an Attester typically
   requires that a Verifier authenticates itself (e.g., at TLS session
   establishment) and might even request a remote attestation before the
   Attester sends the sensitive Evidence.  This can be done by having
   the Attester first act as a Verifier/Relying Party, and the Verifier
   act as its own Attester, as discussed above.

7.3.  Relying Party Owner

   The Relying Party Owner might also require that the Relying Party
   first act as an Attester, providing Evidence that the Owner can
   appraise, before the Owner would give the Relying Party an updated
   policy that might contain sensitive information.  In such a case,
   authentication or attestation in both directions might be needed, in
   which case typically one side's Evidence must be considered safe to
   share with an untrusted entity, in order to bootstrap the sequence.
   See Section 11 for more discussion.

Birkholz, et al.          Expires 9 August 2021                [Page 23]
Internet-Draft              RATS Arch & Terms              February 2021

7.4.  Verifier

   The Verifier trusts (or more specifically, the Verifier's security
   policy is written in a way that configures the Verifier to trust) a
   manufacturer, or the manufacturer's hardware, so as to be able to
   appraise the trustworthiness of that manufacturer's devices.  In a
   typical solution, a Verifier comes to trust an Attester indirectly by
   having an Endorser (such as a manufacturer) vouch for the Attester's
   ability to securely generate Evidence.

   In some solutions, a Verifier might be configured to directly trust
   an Attester by having the Verifier have the Attester's key material
   (rather than the Endorser's) in its trust anchor store.

   Such direct trust must first be established at the time of trust
   anchor store configuration either by checking with an Endorser at
   that time, or by conducting a security analysis of the specific
   device.  Having the Attester directly in the trust anchor store
   narrows the Verifier's trust to only specific devices rather than all
   devices the Endorser might vouch for, such as all devices
   manufactured by the same manufacturer in the case that the Endorser
   is a manufacturer.

   Such narrowing is often important since physical possession of a
   device can also be used to conduct a number of attacks, and so a
   device in a physically secure environment (such as one's own
   premises) may be considered trusted whereas devices owned by others
   would not be.  This often results in a desire to either have the
   owner run their own Endorser that would only Endorse devices one
   owns, or to use Attesters directly in the trust anchor store.  When
   there are many Attesters owned, the use of an Endorser becomes more
   scalable.

   That is, it might appraise the trustworthiness of an application
   component, operating system component, or service under the
   assumption that information provided about it by the lower-layer
   firmware or software is true.  A stronger level of assurance of
   security comes when information can be vouched for by hardware or by
   ROM code, especially if such hardware is physically resistant to
   hardware tampering.  In most cases, components that have to be
   vouched for via Endorsements because no Evidence is generated about
   them are referred to as roots of trust.

Birkholz, et al.          Expires 9 August 2021                [Page 24]
Internet-Draft              RATS Arch & Terms              February 2021

   The manufacturer having arranged for an Attesting Environment to be
   provisioned with key material with which to sign Evidence, the
   Verifier is then provided with some way of verifying the signature on
   the Evidence.  This may be in the form of an appropriate trust
   anchor, or the Verifier may be provided with a database of public
   keys (rather than certificates) or even carefully secured lists of
   symmetric keys.

   The nature of how the Verifier manages to validate the signatures
   produced by the Attester is critical to the secure operation of an
   Attestation system, but is not the subject of standardization within
   this architecture.

   A conveyance protocol that provides authentication and integrity
   protection can be used to convey Evidence that is otherwise
   unprotected (e.g., not signed).  Appropriate conveyance of
   unprotected Evidence (e.g., [I-D.birkholz-rats-uccs]) relies on the
   following conveyance protocol's protection capabilities:

   1.  The key material used to authenticate and integrity protect the
       conveyance channel is trusted by the Verifier to speak for the
       Attesting Environment(s) that collected Claims about the Target
       Environment(s).

   2.  All unprotected Evidence that is conveyed is supplied exclusively
       by the Attesting Environment that has the key material that
       protects the conveyance channel

   3.  The root of trust protects both the conveyance channel key
       material and the Attesting Environment with equivalent strength
       protections.

   See Section 12 for discussion on security strength.

7.5.  Endorser, Reference Value Provider, and Verifier Owner

   In some scenarios, the Endorser, Reference Value Provider, and
   Verifier Owner may need to trust the Verifier before giving the
   Endorsement, Reference Values, or appraisal policy to it.  This can
   be done similarly to how a Relying Party might establish trust in a
   Verifier.

   As discusssed in Section 7.3, authentication or attestation in both
   directions might be needed, in which case typically one side's
   identity or Evidence must be considered safe to share with an
   untrusted entity, in order to bootstrap the sequence.  See Section 11
   for more discussion.

Birkholz, et al.          Expires 9 August 2021                [Page 25]
Internet-Draft              RATS Arch & Terms              February 2021

8.  Conceptual Messages

8.1.  Evidence

   Evidence is a set of claims about the target environment that reveal
   operational status, health, configuration or construction that have
   security relevance.  Evidence is evaluated by a Verifier to establish
   its relevance, compliance, and timeliness.  Claims need to be
   collected in a manner that is reliable.  Evidence needs to be
   securely associated with the target environment so that the Verifier
   cannot be tricked into accepting claims originating from a different
   environment (that may be more trustworthy).  Evidence also must be
   protected from man-in-the-middle attackers who may observe, change or
   misdirect Evidence as it travels from Attester to Verifier.  The
   timeliness of Evidence can be captured using claims that pinpoint the
   time or interval when changes in operational status, health, and so
   forth occur.

8.2.  Endorsements

   An Endorsement is a secure statement that some entity (e.g., a
   manufacturer) vouches for the integrity of the device's signing
   capability.  For example, if the signing capability is in hardware,
   then an Endorsement might be a manufacturer certificate that signs a
   public key whose corresponding private key is only known inside the
   device's hardware.  Thus, when Evidence and such an Endorsement are
   used together, an appraisal procedure can be conducted based on
   appraisal policies that may not be specific to the device instance,
   but merely specific to the manufacturer providing the Endorsement.
   For example, an appraisal policy might simply check that devices from
   a given manufacturer have information matching a set of Reference
   Values, or an appraisal policy might have a set of more complex logic
   on how to appraise the validity of information.

   However, while an appraisal policy that treats all devices from a
   given manufacturer the same may be appropriate for some use cases, it
   would be inappropriate to use such an appraisal policy as the sole
   means of authorization for use cases that wish to constrain _which_
   compliant devices are considered authorized for some purpose.  For
   example, an enterprise using remote attestation for Network Endpoint
   Assessment may not wish to let every healthy laptop from the same
   manufacturer onto the network, but instead only want to let devices
   that it legally owns onto the network.  Thus, an Endorsement may be
   helpful information in authenticating information about a device, but
   is not necessarily sufficient to authorize access to resources which
   may need device-specific information such as a public key for the
   device or component or user on the device.

Birkholz, et al.          Expires 9 August 2021                [Page 26]
Internet-Draft              RATS Arch & Terms              February 2021

8.3.  Attestation Results

   Attestation Results are the input used by the Relying Party to decide
   the extent to which it will trust a particular Attester, and allow it
   to access some data or perform some operation.

   Attestation Results may carry a boolean value indicating compliance
   or non-compliance with a Verifier's appraisal policy, or may carry a
   richer set of Claims about the Attester, against which the Relying
   Party applies its Appraisal Policy for Attestation Results.

   The quality of the Attestation Results depend upon the ability of the
   Verifier to evaluate the Attester.  Different Attesters have a
   different _Strength of Function_ [strengthoffunction], which results
   in the Attestation Results being qualitatively different in strength.

   A result that indicates non-compliance can be used by an Attester (in
   the passport model) or a Relying Party (in the background-check
   model) to indicate that the Attester should not be treated as
   authorized and may be in need of remediation.  In some cases, it may
   even indicate that the Evidence itself cannot be authenticated as
   being correct.

   An Attestation Result that indicates compliance can be used by a
   Relying Party to make authorization decisions based on the Relying
   Party's appraisal policy.  The simplest such policy might be to
   simply authorize any party supplying a compliant Attestation Result
   signed by a trusted Verifier.  A more complex policy might also
   entail comparing information provided in the result against Reference
   Values, or applying more complex logic on such information.

   Thus, Attestation Results often need to include detailed information
   about the Attester, for use by Relying Parties, much like physical
   passports and drivers licenses include personal information such as
   name and date of birth.  Unlike Evidence, which is often very device-
   and vendor-specific, Attestation Results can be vendor-neutral if the
   Verifier has a way to generate vendor-agnostic information based on
   the appraisal of vendor-specific information in Evidence.  This
   allows a Relying Party's appraisal policy to be simpler, potentially
   based on standard ways of expressing the information, while still
   allowing interoperability with heterogeneous devices.

   Finally, whereas Evidence is signed by the device (or indirectly by a
   manufacturer, if Endorsements are used), Attestation Results are
   signed by a Verifier, allowing a Relying Party to only need a trust
   relationship with one entity, rather than a larger set of entities,
   for purposes of its appraisal policy.

Birkholz, et al.          Expires 9 August 2021                [Page 27]
Internet-Draft              RATS Arch & Terms              February 2021

9.  Claims Encoding Formats

   The following diagram illustrates a relationship to which remote
   attestation is desired to be added:

      +-------------+               +------------+ Evaluate
      |             |-------------->|            | request
      |  Attester   |  Access some  |   Relying  | against
      |             |    resource   |    Party   | security
      +-------------+               +------------+ policy

                     Figure 8: Typical Resource Access

   In this diagram, the protocol between Attester and a Relying Party
   can be any new or existing protocol (e.g., HTTP(S), COAP(S), ROLIE
   [RFC8322], 802.1x, OPC UA [OPCUA], etc.), depending on the use case.

   Such protocols typically already have mechanisms for passing security
   information for purposes of authentication and authorization.  Common
   formats include JWTs [RFC7519], CWTs [RFC8392], and X.509
   certificates.

   Retrofitting already deployed protocols with remote attestation
   requires adding RATS conceptual messages to the existing data flows.
   This must be done in a way that doesn't degrade the security
   properties of the system and should use the native extension
   mechanisms provided by the underlying protocol.  For example, if the
   TLS handshake is to be extended with remote attestation capabilities,
   attestation Evidence may be embedded in an ad hoc X.509 certificate
   extension (e.g., [TCG-DICE]), or into a new TLS Certificate Type
   (e.g., [I-D.tschofenig-tls-cwt]).

   Especially for constrained nodes there is a desire to minimize the
   amount of parsing code needed in a Relying Party, in order to both
   minimize footprint and to minimize the attack surface area.  So while
   it would be possible to embed a CWT inside a JWT, or a JWT inside an
   X.509 extension, etc., there is a desire to encode the information
   natively in the format that is natural for the Relying Party.

   This motivates having a common "information model" that describes the
   set of remote attestation related information in an encoding-agnostic
   way, and allowing multiple encoding formats (CWT, JWT, X.509, etc.)
   that encode the same information into the claims format needed by the
   Relying Party.

   The following diagram illustrates that Evidence and Attestation
   Results might each have multiple possible encoding formats, so that
   they can be conveyed by various existing protocols.  It also

Birkholz, et al.          Expires 9 August 2021                [Page 28]
Internet-Draft              RATS Arch & Terms              February 2021

   motivates why the Verifier might also be responsible for accepting
   Evidence that encodes claims in one format, while issuing Attestation
   Results that encode claims in a different format.

                   Evidence           Attestation Results
   .--------------.   CWT                    CWT   .-------------------.
   |  Attester-A  |------------.      .----------->|  Relying Party V  |
   '--------------'            v      |            `-------------------'
   .--------------.   JWT   .------------.   JWT   .-------------------.
   |  Attester-B  |-------->|  Verifier  |-------->|  Relying Party W  |
   '--------------'         |            |         `-------------------'
   .--------------.  X.509  |            |  X.509  .-------------------.
   |  Attester-C  |-------->|            |-------->|  Relying Party X  |
   '--------------'         |            |         `-------------------'
   .--------------.   TPM   |            |   TPM   .-------------------.
   |  Attester-D  |-------->|            |-------->|  Relying Party Y  |
   '--------------'         '------------'         `-------------------'
   .--------------.  other     ^      |     other  .-------------------.
   |  Attester-E  |------------'      '----------->|  Relying Party Z  |
   '--------------'                                `-------------------'

      Figure 9: Multiple Attesters and Relying Parties with Different
                                  Formats

10.  Freshness

   A Verifier or Relying Party may need to learn the point in time
   (i.e., the "epoch") an Evidence or Attestation Result has been
   produced.  This is essential in deciding whether the included Claims
   and their values can be considered fresh, meaning they still reflect
   the latest state of the Attester, and that any Attestation Result was
   generated using the latest Appraisal Policy for Evidence.

   Freshness is assessed based on the Appraisal Policy for Evidence or
   Attestation Results that compares the estimated epoch against an
   "expiry" threshold defined locally to that policy.  There is,
   however, always a race condition possible in that the state of the
   Attester, and the appraisal policies might change immediately after
   the Evidence or Attestation Result was generated.  The goal is merely
   to narrow their recentness to something the Verifier (for Evidence)
   or Relying Party (for Attestation Result) is willing to accept.  Some
   flexibility on the freshness requirement is a key component for
   enabling caching and reuse of both Evidence and Attestation Results,
   which is especially valuable in cases where their computation uses a
   substantial part of the resource budget (e.g., energy in constrained
   devices).

Birkholz, et al.          Expires 9 August 2021                [Page 29]
Internet-Draft              RATS Arch & Terms              February 2021

   There are three common approaches for determining the epoch of
   Evidence or an Attestation Result.

10.1.  Explicit Timekeeping using Synchronized Clocks

   The first approach is to rely on synchronized and trustworthy clocks,
   and include a signed timestamp (see [I-D.birkholz-rats-tuda]) along
   with the Claims in the Evidence or Attestation Result.  Timestamps
   can also be added on a per-Claim basis to distinguish the time of
   creation of Evidence or Attestation Result from the time that a
   specific Claim was generated.  The clock's trustworthiness typically
   requires additional Claims about the signer's time synchronization
   mechanism.

10.2.  Implicit Timekeeping using Nonces

   A second approach places the onus of timekeeping solely on the
   Verifier (for Evidence) or the Relying Party (for Attestation
   Results), and might be suitable, for example, in case the Attester
   does not have a reliable clock or time synchronization is otherwise
   impaired.  In this approach, a non-predictable nonce is sent by the
   appraising entity, and the nonce is then signed and included along
   with the Claims in the Evidence or Attestation Result.  After
   checking that the sent and received nonces are the same, the
   appraising entity knows that the Claims were signed after the nonce
   was generated.  This allows associating a "rough" epoch to the
   Evidence or Attestation Result.  In this case the epoch is said to be
   rough because:

   *  The epoch applies to the entire claim set instead of a more
      granular association, and

   *  The time between the creation of Claims and the collection of
      Claims is indistinguishable.

10.3.  Implicit Timekeeping using Epoch Handles

   A third approach relies on having epoch "handles" periodically sent
   to both the sender and receiver of Evidence or Attestation Results by
   some "Handle Distributor".

   Handles are different from nonces as they can be used more than once
   and can even be used by more than one entity at the same time.
   Handles are different from timestamps as they do not have to convey
   information about a point in time, i.e., they are not necessarily
   monotonically increasing integers.

Birkholz, et al.          Expires 9 August 2021                [Page 30]
Internet-Draft              RATS Arch & Terms              February 2021

   Like the nonce approach, this allows associating a "rough" epoch
   without requiring a reliable clock or time synchronization in order
   to generate or appraise the freshness of Evidence or Attestation
   Results.  Only the Handle Distributor requires access to a clock so
   it can periodically send new epoch handles.

   The most recent handle is included in the produced Evidence or
   Attestation Results, and the appraising entity can compare the handle
   in received Evidence or Attestation Results against the latest handle
   it received from the Handle Distributor to determine if it is within
   the current epoch.  An actual solution also needs to take into
   account race conditions when transitioning to a new epoch, such as by
   using a counter signed by the Handle Distributor as the handle, or by
   including both the current and previous handles in messages and/or
   checks, by requiring retries in case of mismatching handles, or by
   buffering incoming messages that might be associated with a handle
   that the receiver has not yet obtained.

   More generally, in order to prevent an appraising entity from
   generating false negatives (e.g., discarding Evidence that is deemed
   stale even if it is not), the appraising entity should keep an "epoch
   window" consisting of the most recently received handles.  The depth
   of such epoch window is directly proportional to the maximum network
   propagation delay between the first to receive the handle and the
   last to receive the handle, and it is inversely proportional to the
   epoch duration.  The appraising entity shall compare the handle
   carried in the received Evidence or Attestation Result with the
   handles in its epoch window to find a suitable match.

   Whereas the nonce approach typically requires the appraising entity
   to keep state for each nonce generated, the handle approach minimizes
   the state kept to be independent of the number of Attesters or
   Verifiers from which it expects to receive Evidence or Attestation
   Results, as long as all use the same Handle Distributor.

10.4.  Discussion

   Implicit and explicit timekeeping can be combined into hybrid
   mechanisms.  For example, if clocks exist and are considered
   trustworthy but are not synchronized, a nonce-based exchange may be
   used to determine the (relative) time offset between the involved
   peers, followed by any number of timestamp based exchanges.

Birkholz, et al.          Expires 9 August 2021                [Page 31]
Internet-Draft              RATS Arch & Terms              February 2021

   It is important to note that the actual values in Claims might have
   been generated long before the Claims are signed.  If so, it is the
   signer's responsibility to ensure that the values are still correct
   when they are signed.  For example, values generated at boot time
   might have been saved to secure storage until network connectivity is
   established to the remote Verifier and a nonce is obtained.

   A more detailed discussion with examples appears in Section 16.

   For a discussion on the security of handles see Section 12.3.

11.  Privacy Considerations

   The conveyance of Evidence and the resulting Attestation Results
   reveal a great deal of information about the internal state of a
   device as well as potentially any users of the device.  In many
   cases, the whole point of the Attestation process is to provide
   reliable information about the type of the device and the firmware/
   software that the device is running.  This information might be
   particularly interesting to many attackers.  For example, knowing
   that a device is running a weak version of firmware provides a way to
   aim attacks better.

   Many claims in Attestation Evidence and Attestation Results are
   potentially Personally Identifying Information) depending on the end-
   to-end use case of the attestation.  Attestation that goes up to
   include containers and applications may further reveal details about
   a specific system or user.

   In some cases, an attacker may be able to make inferences about
   attestations from the results or timing of the processing.  For
   example, an attacker might be able to infer the value of specific
   claims if it knew that only certain values were accepted by the
   Relying Party.

   Evidence and Attestation Results data structures are expected to
   support integrity protection encoding (e.g., COSE, JOSE, X.509) and
   optionally might support confidentiality protection (e.g., COSE,
   JOSE).  Therefore, if confidentiality protection is omitted or
   unavailable, the protocols that convey Evidence or Attestation
   Results are responsible for detailing what kinds of information are
   disclosed, and to whom they are exposed.

   Furthermore, because Evidence might contain sensitive information,
   Attesters are responsible for only sending such Evidence to trusted
   Verifiers.  Some Attesters might want a stronger level of assurance
   of the trustworthiness of a Verifier before sending Evidence to it.
   In such cases, an Attester can first act as a Relying Party and ask

Birkholz, et al.          Expires 9 August 2021                [Page 32]
Internet-Draft              RATS Arch & Terms              February 2021

   for the Verifier's own Attestation Result, and appraising it just as
   a Relying Party would appraise an Attestation Result for any other
   purpose.

   Another approach to deal with Evidence is to remove PII from the
   Evidence while still being able to verify that the Attester is one of
   a large set.  This approach is often called "Direct Anonymous
   Attestation".  See [CCC-DeepDive] section 6.2 for more discussion.

12.  Security Considerations

12.1.  Attester and Attestation Key Protection

   Implementers need to pay close attention to the protection of the
   Attester and the factory processes for provisioning the Attestation
   key material.  If either of these are compromised, the remote
   attestation becomes worthless because an attacker can forge Evidence
   or manipulate the Attesting Environment.  For example, a Target
   Environment should not be able to tamper with the Attesting
   Environment that measures it, by isolating the two environments from
   each other in some way.

   Remote attestation applies to use cases with a range of security
   requirements, so the protections discussed here range from low to
   high security where low security may be only application or process
   isolation by the device's operating system and high security involves
   specialized hardware to defend against physical attacks on a chip.

12.1.1.  On-Device Attester and Key Protection

   It is assumed that an Attesting Environment is sufficiently isolated
   from the Target Environment it collects Claims for and signs them
   with an Attestation Key, so that the Target Environment cannot forge
   Evidence about itself.  Such an isolated environment might be
   provided by a process, a dedicated chip, a TEE, a virtual machine, or
   another secure mode of operation.  The Attesting Environment must be
   protected from unauthorized modification to ensure it behaves
   correctly.  There must also be confidentiality so that the signing
   key is not captured and used elsewhere to forge Evidence.

   In many cases the user or owner of the device must not be able to
   modify or exfiltrate keys from the Attesting Environment of the
   Attester.  For example the owner or user of a mobile phone or FIDO
   authenticator, having full control over the keys, might not be
   trusted to use the keys to report Evidence about the environment that
   protects the keys.  The point of remote attestation is for the
   Relying Party to be able to trust the Attester even though they don't
   trust the user or owner.

Birkholz, et al.          Expires 9 August 2021                [Page 33]
Internet-Draft              RATS Arch & Terms              February 2021

   Some of the measures for a minimally protected system might include
   process or application isolation by a high-level operating system,
   and perhaps restricting access to root or system privilege.  For
   extremely simple single-use devices that don't use a protected mode
   operating system, like a Bluetooth speaker, the isolation might only
   be the plastic housing for the device.

   Measures for a moderately protected system could include a special
   restricted operating environment like a Trusted Execution Environment
   (TEE) might be used.  In this case, only security-oriented software
   has access to the Attester and key material.

   Measures for a highly protected system could include specialized
   hardware that is used to provide protection against chip decapping
   attacks, power supply and clock glitching, faulting injection and RF
   and power side channel attacks.

12.1.2.  Attestation Key Provisioning Processes

   Attestation key provisioning is the process that occurs in the
   factory or elsewhere that establishes the signing key material on the
   device and the verification key material off the device.  Sometimes
   this is referred to as "personalization".

   One way to provision a key is to first generate it external to the
   device and then copy the key onto the device.  In this case,
   confidentiality of the generator, as well as the path over which the
   key is provisioned, is necessary.  The manufacturer needs to take
   care to protect it with measures consistent with its value.  This can
   be achieved in a number of ways.

   Confidentiality can be achieved entirely with physical provisioning
   facility security involving no encryption at all.  For low-security
   use cases, this might be simply locking doors and limiting personnel
   that can enter the facility.  For high-security use cases, this might
   involve a special area of the facility accessible only to select
   security-trained personnel.

   Cryptography can also be used to support confidentiality, but keys
   that are used to then provision attestation keys must somehow have
   been provisioned securely beforehand (a recursive problem).

   In many cases both some physical security and some cryptography will
   be necessary and useful to establish confidentiality.

Birkholz, et al.          Expires 9 August 2021                [Page 34]
Internet-Draft              RATS Arch & Terms              February 2021

   Another way to provision the key material is to generate it on the
   device and export the verification key.  If public key cryptography
   is being used, then only integrity is necessary.  Confidentiality is
   not necessary.

   In all cases, the Attestation Key provisioning process must ensure
   that only attestation key material that is generated by a valid
   Endorser is established in Attesters and then configured correctly.
   For many use cases, this will involve physical security at the
   facility, to prevent unauthorized devices from being manufactured
   that may be counterfeit or incorrectly configured.

12.2.  Integrity Protection

   Any solution that conveys information used for security purposes,
   whether such information is in the form of Evidence, Attestation
   Results, Endorsements, or appraisal policy must support end-to-end
   integrity protection and replay attack prevention, and often also
   needs to support additional security properties, including:

   *  end-to-end encryption,

   *  denial of service protection,

   *  authentication,

   *  auditing,

   *  fine grained access controls, and

   *  logging.

   Section 10 discusses ways in which freshness can be used in this
   architecture to protect against replay attacks.

   To assess the security provided by a particular appraisal policy, it
   is important to understand the strength of the root of trust, e.g.,
   whether it is mutable software, or firmware that is read-only after
   boot, or immutable hardware/ROM.

   It is also important that the appraisal policy was itself obtained
   securely.  If an attacker can configure appraisal policies for a
   Relying Party or for a Verifier, then integrity of the process is
   compromised.

   The security of conveyed information may be applied at different
   layers, whether by a conveyance protocol, or an information encoding
   format.  This architecture expects attestation messages (i.e.,

Birkholz, et al.          Expires 9 August 2021                [Page 35]
Internet-Draft              RATS Arch & Terms              February 2021

   Evidence, Attestation Results, Endorsements, Reference Values, and
   Policies) are end-to-end protected based on the role interaction
   context.  For example, if an Attester produces Evidence that is
   relayed through some other entity that doesn't implement the Attester
   or the intended Verifier roles, then the relaying entity should not
   expect to have access to the Evidence.

12.3.  Handle-based Attestation

   Handles, described in Section 10.3, can be tampered with, dropped,
   delayed and reordered by an attacker.

   An attacker could be either external or belong to the distribution
   group, for example if one of the Attester entities have been
   compromised.

   An attacker who is able to tamper with handles can potentially lock
   all the participants in a certain epoch of choice for ever,
   effectively freezing time.  This is problematic since it destroys the
   ability to ascertain freshness of Evidence and Attestation Results.

   To mitigate this threat, the transport should be at least integrity
   protected and provide origin authentication.

   Selective dropping of handles is equivalent to pinning the victim
   node to a past epoch.  An attacker could drop handles to only some
   entities and not others, which will typically result in a denial of
   service due to the permanent staleness of the Attestation Result or
   Evidence.

   Delaying or reordering handles is equivalent to manipulating the
   victim's timeline at will.  This ability could be used by a malicious
   actor (e.g., a compromised router) to mount a confusion attack where,
   for example, a Verifier is tricked into accepting Evidence coming
   from a past epoch as fresh, while in the meantime the Attester has
   been compromised.

   Reordering and dropping attacks are mitigated if the transport
   provides the ability to detect reordering and drop.  However, the
   delay attack described above can't be thwarted in this manner.

13.  IANA Considerations

   This document does not require any actions by IANA.

Birkholz, et al.          Expires 9 August 2021                [Page 36]
Internet-Draft              RATS Arch & Terms              February 2021

14.  Acknowledgments

   Special thanks go to Joerg Borchert, Nancy Cam-Winget, Jessica
   Fitzgerald-McKay, Diego Lopez, Laurence Lundblade, Paul Rowe, Hannes
   Tschofenig, Frank Xia, and David Wooten.

15.  Notable Contributions

   Thomas Hardjono created older versions of the terminology section in
   collaboration with Ned Smith.  Eric Voit provided the conceptual
   separation between Attestation Provision Flows and Attestation
   Evidence Flows.  Monty Wisemen created the content structure of the
   first three architecture drafts.  Carsten Bormann provided many of
   the motivational building blocks with respect to the Internet Threat
   Model.

16.  Appendix A: Time Considerations

   The table below defines a number of relevant events, with an ID that
   is used in subsequent diagrams.  The times of said events might be
   defined in terms of an absolute clock time such as Coordinated
   Universal Time, or might be defined relative to some other timestamp
   or timeticks counter.

   +====+============+=================================================+
   | ID | Event      | Explanation of event                            |
   +====+============+=================================================+
   | VG | Value      | A value to appear in a Claim was created.       |
   |    | generated  | In some cases, a value may have technically     |
   |    |            | existed before an Attester became aware of      |
   |    |            | it but the Attester might have no idea how      |
   |    |            | long it has had that value.  In such a          |
   |    |            | case, the Value created time is the time at     |
   |    |            | which the Claim containing the copy of the      |
   |    |            | value was created.                              |
   +----+------------+-------------------------------------------------+
   | NS | Nonce sent | A nonce not predictable to an Attester          |
   |    |            | (recentness & uniqueness) is sent to an         |
   |    |            | Attester.                                       |
   +----+------------+-------------------------------------------------+
   | NR | Nonce      | A nonce is relayed to an Attester by            |
   |    | relayed    | another entity.                                 |
   +----+------------+-------------------------------------------------+
   | HR | Handle     | A handle is successfully received and           |
   |    | received   | processed by an entity.                         |
   +----+------------+-------------------------------------------------+
   | EG | Evidence   | An Attester creates Evidence from collected     |
   |    | generation | Claims.                                         |

Birkholz, et al.          Expires 9 August 2021                [Page 37]
Internet-Draft              RATS Arch & Terms              February 2021

   +----+------------+-------------------------------------------------+
   | ER | Evidence   | A Relying Party relays Evidence to a            |
   |    | relayed    | Verifier.                                       |
   +----+------------+-------------------------------------------------+
   | RG | Result     | A Verifier appraises Evidence and generates     |
   |    | generation | an Attestation Result.                          |
   +----+------------+-------------------------------------------------+
   | RR | Result     | A Relying Party relays an Attestation           |
   |    | relayed    | Result to a Relying Party.                      |
   +----+------------+-------------------------------------------------+
   | RA | Result     | The Relying Party appraises Attestation         |
   |    | appraised  | Results.                                        |
   +----+------------+-------------------------------------------------+
   | OP | Operation  | The Relying Party performs some operation       |
   |    | performed  | requested by the Attester.  For example,        |
   |    |            | acting upon some message just received          |
   |    |            | across a session created earlier at             |
   |    |            | time(RA).                                       |
   +----+------------+-------------------------------------------------+
   | RX | Result     | An Attestation Result should no longer be       |
   |    | expiry     | accepted, according to the Verifier that        |
   |    |            | generated it.                                   |
   +----+------------+-------------------------------------------------+

                                  Table 1

   Using the table above, a number of hypothetical examples of how a
   solution might be built are illustrated below. a solution might be
   built.  This list is not intended to be complete, but is just
   representative enough to highlight various timing considerations.

   All times are relative to the local clocks, indicated by an "a"
   (Attester), "v" (Verifier), or "r" (Relying Party) suffix.

   Times with an appended Prime (') indicate a second instance of the
   same event.

   How and if clocks are synchronized depends upon the model.

16.1.  Example 1: Timestamp-based Passport Model Example

   The following example illustrates a hypothetical Passport Model
   solution that uses timestamps and requires roughly synchronized
   clocks between the Attester, Verifier, and Relying Party, which
   depends on using a secure clock synchronization mechanism.  As a
   result, the receiver of a conceptual message containing a timestamp
   can directly compare it to its own clock and timestamps.

Birkholz, et al.          Expires 9 August 2021                [Page 38]
Internet-Draft              RATS Arch & Terms              February 2021

      .----------.                     .----------.  .---------------.
      | Attester |                     | Verifier |  | Relying Party |
      '----------'                     '----------'  '---------------'
        time(VG_a)                           |               |
           |                                 |               |
           ~                                 ~               ~
           |                                 |               |
        time(EG_a)                           |               |
           |------Evidence{time(EG_a)}------>|               |
           |                              time(RG_v)         |
           |<-----Attestation Result---------|               |
           |      {time(RG_v),time(RX_v)}    |               |
           ~                                                 ~
           |                                                 |
           |----Attestation Result{time(RG_v),time(RX_v)}-->time(RA_r)
           |                                                 |
           ~                                                 ~
           |                                                 |
           |                                              time(OP_r)

   In the figures above and in subsequent sections, curly braces
   indicate containment.  For example, the notation Evidence{foo}
   indicates that 'foo' is contained in the Evidence and is thus covered
   by its signature.

   The Verifier can check whether the Evidence is fresh when appraising
   it at time(RG_v) by checking "time(RG_v) - time(EG_a) < Threshold",
   where the Verifier's threshold is large enough to account for the
   maximum permitted clock skew between the Verifier and the Attester.

   If time(VG_a) is also included in the Evidence along with the claim
   value generated at that time, and the Verifier decides that it can
   trust the time(VG_a) value, the Verifier can also determine whether
   the claim value is recent by checking "time(RG_v) - time(VG_a) <
   Threshold".  The threshold is decided by the Appraisal Policy for
   Evidence, and again needs to take into account the maximum permitted
   clock skew between the Verifier and the Attester.

Birkholz, et al.          Expires 9 August 2021                [Page 39]
Internet-Draft              RATS Arch & Terms              February 2021

   The Relying Party can check whether the Attestation Result is fresh
   when appraising it at time(RA_r) by checking "time(RA_r) - time(RG_v)
   < Threshold", where the Relying Party's threshold is large enough to
   account for the maximum permitted clock skew between the Relying
   Party and the Verifier.  The result might then be used for some time
   (e.g., throughout the lifetime of a connection established at
   time(RA_r)).  The Relying Party must be careful, however, to not
   allow continued use beyond the period for which it deems the
   Attestation Result to remain fresh enough.  Thus, it might allow use
   (at time(OP_r)) as long as "time(OP_r) - time(RG_v) < Threshold".
   However, if the Attestation Result contains an expiry time time(RX_v)
   then it could explicitly check "time(OP_r) < time(RX_v)".

16.2.  Example 2: Nonce-based Passport Model Example

   The following example illustrates a hypothetical Passport Model
   solution that uses nonces instead of timestamps.  Compared to the
   timestamp-based example, it requires an extra round trip to retrieve
   a nonce, and requires that the Verifier and Relying Party track state
   to remember the nonce for some period of time.

   The advantage is that it does not require that any clocks are
   synchronized.  As a result, the receiver of a conceptual message
   containing a timestamp cannot directly compare it to its own clock or
   timestamps.  Thus we use a suffix ("a" for Attester, "v" for
   Verifier, and "r" for Relying Party) on the IDs below indicating
   which clock generated them, since times from different clocks cannot
   be compared.  Only the delta between two events from the sender can
   be used by the receiver.

Birkholz, et al.          Expires 9 August 2021                [Page 40]
Internet-Draft              RATS Arch & Terms              February 2021

      .----------.                     .----------.  .---------------.
      | Attester |                     | Verifier |  | Relying Party |
      '----------'                     '----------'  '---------------'
        time(VG_a)                           |               |
           |                                 |               |
           ~                                 ~               ~
           |                                 |               |
           |<--Nonce1---------------------time(NS_v)         |
        time(EG_a)                           |               |
           |---Evidence--------------------->|               |
           | {Nonce1, time(EG_a)-time(VG_a)} |               |
           |                              time(RG_v)         |
           |<--Attestation Result------------|               |
           |   {time(RX_v)-time(RG_v)}       |               |
           ~                                                 ~
           |                                                 |
           |<--Nonce2-------------------------------------time(NS_r)
        time(RR_a)                                           |
           |--[Attestation Result{time(RX_v)-time(RG_v)}, -->|time(RA_r)
           |        Nonce2, time(RR_a)-time(EG_a)]           |
           ~                                                 ~
           |                                                 |
           |                                              time(OP_r)

   In this example solution, the Verifier can check whether the Evidence
   is fresh at "time(RG_v)" by verifying that "time(RG_v)-time(NS_v) <
   Threshold".

   The Verifier cannot, however, simply rely on a Nonce to determine
   whether the value of a claim is recent, since the claim value might
   have been generated long before the nonce was sent by the Verifier.
   However, if the Verifier decides that the Attester can be trusted to
   correctly provide the delta "time(EG_a)-time(VG_a)", then it can
   determine recency by checking "time(RG_v)-time(NS_v) + time(EG_a)-
   time(VG_a) < Threshold".

   Similarly if, based on an Attestation Result from a Verifier it
   trusts, the Relying Party decides that the Attester can be trusted to
   correctly provide time deltas, then it can determine whether the
   Attestation Result is fresh by checking "time(OP_r)-time(NS_r) +
   time(RR_a)-time(EG_a) < Threshold".  Although the Nonce2 and
   "time(RR_a)-time(EG_a)" values cannot be inside the Attestation
   Result, they might be signed by the Attester such that the
   Attestation Result vouches for the Attester's signing capability.

   The Relying Party must still be careful, however, to not allow
   continued use beyond the period for which it deems the Attestation
   Result to remain valid.  Thus, if the Attestation Result sends a

Birkholz, et al.          Expires 9 August 2021                [Page 41]
Internet-Draft              RATS Arch & Terms              February 2021

   validity lifetime in terms of "time(RX_v)-time(RG_v)", then the
   Relying Party can check "time(OP_r)-time(NS_r) < time(RX_v)-
   time(RG_v)".

16.3.  Example 3: Handle-based Passport Model Example

   The example in Figure 10 illustrates a hypothetical Passport Model
   solution that uses handles instead of nonces or timestamps.

   The Handle Distributor broadcasts handle "H" which starts a new epoch
   "E" for a protocol participant upon reception at "time(HR)".

   The Attester generates Evidence incorporating handle "H" and conveys
   it to the Verifier.

   The Verifier appraises that the received handle "H" is "fresh"
   according to the definition provided in Section 10.3 whereby retries
   are required in the case of mismatching handles, and generates an
   Attestation Result.  The Attestation Result is conveyed to the
   Attester.

   After the transmission of handle "H'" a new epoch "E'" is established
   when "H'" is received by each protocol participant.  The Attester
   relays the Attestation Result obtained during epoch "E" (associated
   with handle "H") to the Relying Party using the handle for the
   current epoch "H'".  If the Relying Party had not yet received "H'",
   then the Attestation Result would be rejected, but in this example,
   it is received.

   In the illustrated scenario, the handle for relaying an Attestation
   Result to the Relying Party is current, while a previous handle was
   used to generate Verifier evaluated evidence.  This indicates that at
   least one epoch transition has occurred, and the Attestation Results
   may only be as fresh as the previous epoch.

Birkholz, et al.          Expires 9 August 2021                [Page 42]
Internet-Draft              RATS Arch & Terms              February 2021

                    .-------------.
     .----------.   | Handle      |   .----------.  .---------------.
     | Attester |   | Distributor |   | Verifier |  | Relying Party |
     '----------'   '-------------'   '----------'  '---------------'
       time(VG_a)          |                |               |
          |                |                |               |
          ~                ~                ~               ~
          |                |                |               |
       time(HR_a)<---------+-----------time(HR_v)----->time(HR_r)
          |                |                |               |
       time(EG_a)          |                |               |
          |---Evidence{H,time(EG_a)-time(VG_a)}----->|               |
          |                |                |               |
          |                |           time(RG_v)           |
          |<--Attestation Result------------|               |
          |   {H,time(RX_v)-time(RG_v)}                |               |
          |                |                |               |
       time(HR'_a)<--------+-----------time(HR'_v)---->time(HR'_r)
          |                |                |               |
       time(RR_a)          |                |               |
          |---Attestation Result---------------------->time(RA_r)
          |   {H',R{H,time(RX_v)-time(RG_v)}}          |               |
          |                |                |               |
          ~                ~                ~               ~
          |                |                |               |
          |                |                |          time(OP_r)

                  Figure 10: Handle-based Passport Model

16.4.  Example 4: Timestamp-based Background-Check Model Example

   The following example illustrates a hypothetical Background-Check
   Model solution that uses timestamps and requires roughly synchronized
   clocks between the Attester, Verifier, and Relying Party.

Birkholz, et al.          Expires 9 August 2021                [Page 43]
Internet-Draft              RATS Arch & Terms              February 2021

   .----------.         .---------------.                .----------.
   | Attester |         | Relying Party |                | Verifier |
   '----------'         '---------------'                '----------'
     time(VG_a)                 |                             |
           |                    |                             |
           ~                    ~                             ~
           |                    |                             |
     time(EG_a)                 |                             |
           |----Evidence------->|                             |
           |   {time(EG_a)} time(ER_r)--Evidence{time(EG_a)}->|
           |                    |                        time(RG_v)
           |                 time(RA_r)<-Attestation Result---|
           |                    |           {time(RX_v)}      |
           ~                    ~                             ~
           |                    |                             |
           |                 time(OP_r)                       |

   The time considerations in this example are equivalent to those
   discussed under Example 1 above.

16.5.  Example 5: Nonce-based Background-Check Model Example

   The following example illustrates a hypothetical Background-Check
   Model solution that uses nonces and thus does not require that any
   clocks are synchronized.  In this example solution, a nonce is
   generated by a Verifier at the request of a Relying Party, when the
   Relying Party needs to send one to an Attester.

   .----------.         .---------------.              .----------.
   | Attester |         | Relying Party |              | Verifier |
   '----------'         '---------------'              '----------'
     time(VG_a)                 |                           |
        |                       |                           |
        ~                       ~                           ~
        |                       |                           |
        |                       |<-------Nonce-----------time(NS_v)
        |<---Nonce-----------time(NR_r)                     |
     time(EG_a)                 |                           |
        |----Evidence{Nonce}--->|                           |
        |                    time(ER_r)--Evidence{Nonce}--->|
        |                       |                        time(RG_v)
        |                    time(RA_r)<-Attestation Result-|
        |                       |   {time(RX_v)-time(RG_v)} |
        ~                       ~                           ~
        |                       |                           |
        |                    time(OP_r)                     |

Birkholz, et al.          Expires 9 August 2021                [Page 44]
Internet-Draft              RATS Arch & Terms              February 2021

   The Verifier can check whether the Evidence is fresh, and whether a
   claim value is recent, the same as in Example 2 above.

   However, unlike in Example 2, the Relying Party can use the Nonce to
   determine whether the Attestation Result is fresh, by verifying that
   "time(OP_r)-time(NR_r) < Threshold".

   The Relying Party must still be careful, however, to not allow
   continued use beyond the period for which it deems the Attestation
   Result to remain valid.  Thus, if the Attestation Result sends a
   validity lifetime in terms of "time(RX_v)-time(RG_v)", then the
   Relying Party can check "time(OP_r)-time(ER_r) < time(RX_v)-
   time(RG_v)".

17.  References

17.1.  Normative References

   [RFC7519]  Jones, M., Bradley, J., and N. Sakimura, "JSON Web Token
              (JWT)", RFC 7519, DOI 10.17487/RFC7519, May 2015,
              <https://www.rfc-editor.org/info/rfc7519>.

   [RFC8392]  Jones, M., Wahlstroem, E., Erdtman, S., and H. Tschofenig,
              "CBOR Web Token (CWT)", RFC 8392, DOI 10.17487/RFC8392,
              May 2018, <https://www.rfc-editor.org/info/rfc8392>.

17.2.  Informative References

   [CCC-DeepDive]
              Confidential Computing Consortium, "Confidential Computing
              Deep Dive", n.d.,
              <https://confidentialcomputing.io/whitepaper-02-latest>.

   [CTAP]     FIDO Alliance, "Client to Authenticator Protocol", n.d.,
              <https://fidoalliance.org/specs/fido-v2.0-id-20180227/
              fido-client-to-authenticator-protocol-v2.0-id-
              20180227.html>.

   [I-D.birkholz-rats-tuda]
              Fuchs, A., Birkholz, H., McDonald, I., and C. Bormann,
              "Time-Based Uni-Directional Attestation", Work in
              Progress, Internet-Draft, draft-birkholz-rats-tuda-04, 13
              January 2021, <http://www.ietf.org/internet-drafts/draft-
              birkholz-rats-tuda-04.txt>.

   [I-D.birkholz-rats-uccs]
              Birkholz, H., O'Donoghue, J., Cam-Winget, N., and C.
              Bormann, "A CBOR Tag for Unprotected CWT Claims Sets",

Birkholz, et al.          Expires 9 August 2021                [Page 45]
Internet-Draft              RATS Arch & Terms              February 2021

              Work in Progress, Internet-Draft, draft-birkholz-rats-
              uccs-02, 2 December 2020, <http://www.ietf.org/internet-
              drafts/draft-birkholz-rats-uccs-02.txt>.

   [I-D.ietf-teep-architecture]
              Pei, M., Tschofenig, H., Thaler, D., and D. Wheeler,
              "Trusted Execution Environment Provisioning (TEEP)
              Architecture", Work in Progress, Internet-Draft, draft-
              ietf-teep-architecture-13, 2 November 2020,
              <http://www.ietf.org/internet-drafts/draft-ietf-teep-
              architecture-13.txt>.

   [I-D.tschofenig-tls-cwt]
              Tschofenig, H. and M. Brossard, "Using CBOR Web Tokens
              (CWTs) in Transport Layer Security (TLS) and Datagram
              Transport Layer Security (DTLS)", Work in Progress,
              Internet-Draft, draft-tschofenig-tls-cwt-02, 13 July 2020,
              <http://www.ietf.org/internet-drafts/draft-tschofenig-tls-
              cwt-02.txt>.

   [OPCUA]    OPC Foundation, "OPC Unified Architecture Specification,
              Part 2: Security Model, Release 1.03", OPC 10000-2 , 25
              November 2015, <https://opcfoundation.org/developer-tools/
              specifications-unified-architecture/part-2-security-
              model/>.

   [RFC4949]  Shirey, R., "Internet Security Glossary, Version 2",
              FYI 36, RFC 4949, DOI 10.17487/RFC4949, August 2007,
              <https://www.rfc-editor.org/info/rfc4949>.

   [RFC8322]  Field, J., Banghart, S., and D. Waltermire, "Resource-
              Oriented Lightweight Information Exchange (ROLIE)",
              RFC 8322, DOI 10.17487/RFC8322, February 2018,
              <https://www.rfc-editor.org/info/rfc8322>.

   [strengthoffunction]
              NISC, "Strength of Function", n.d.,
              <https://csrc.nist.gov/glossary/term/
              strength_of_function>.

   [TCG-DICE] Trusted Computing Group, "DICE Certificate Profiles",
              n.d., <https://trustedcomputinggroup.org/wp-
              content/uploads/DICE-Certificate-Profiles-
              r01_3june2020-1.pdf>.

Birkholz, et al.          Expires 9 August 2021                [Page 46]
Internet-Draft              RATS Arch & Terms              February 2021

   [TCGarch]  Trusted Computing Group, "Trusted Platform Module Library
              - Part 1: Architecture", 8 November 2019,
              <https://trustedcomputinggroup.org/wp-content/uploads/
              TCG_TPM2_r1p59_Part1_Architecture_pub.pdf>.

   [WebAuthN] W3C, "Web Authentication: An API for accessing Public Key
              Credentials", n.d., <https://www.w3.org/TR/webauthn-1/>.

Contributors

   Monty Wiseman

   Email: montywiseman32@gmail.com

   Liang Xia

   Email: frank.xialiang@huawei.com

   Laurence Lundblade

   Email: lgl@island-resort.com

   Eliot Lear

   Email: elear@cisco.com

   Jessica Fitzgerald-McKay

   Sarah C. Helbe

   Andrew Guinn

   Peter Lostcco

   Email: pete.loscocco@gmail.com

   Eric Voit

Birkholz, et al.          Expires 9 August 2021                [Page 47]
Internet-Draft              RATS Arch & Terms              February 2021

   Thomas Fossati

   Email: thomas.fossati@arm.com

   Paul Rowe

   Carsten Bormann

   Email: cabo@tzi.org

   Giri Mandyam

   Email: mandyam@qti.qualcomm.com

Authors' Addresses

   Henk Birkholz
   Fraunhofer SIT
   Rheinstrasse 75
   64295 Darmstadt
   Germany

   Email: henk.birkholz@sit.fraunhofer.de

   Dave Thaler
   Microsoft
   United States of America

   Email: dthaler@microsoft.com

   Michael Richardson
   Sandelman Software Works
   Canada

   Email: mcr+ietf@sandelman.ca

   Ned Smith
   Intel Corporation
   United States of America

   Email: ned.smith@intel.com

Birkholz, et al.          Expires 9 August 2021                [Page 48]
Internet-Draft              RATS Arch & Terms              February 2021

   Wei Pan
   Huawei Technologies

   Email: william.panwei@huawei.com

Birkholz, et al.          Expires 9 August 2021                [Page 49]