A Non-Queue-Building Per-Hop Behavior (NQB PHB) for Differentiated Services
draft-ietf-tsvwg-nqb-00
The information below is for an old version of the document.
| Document | Type | Active Internet-Draft (tsvwg WG) | |
|---|---|---|---|
| Authors | Greg White , Thomas Fossati | ||
| Last updated | 2019-11-17 (Latest revision 2019-11-04) | ||
| Replaces | draft-white-tsvwg-nqb | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text xml htmlized pdfized bibtex | ||
| Stream | WG state | WG Document | |
| Associated WG milestone |
|
||
| Document shepherd | David L. Black | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | David Black <david.black@dell.com> |
draft-ietf-tsvwg-nqb-00
Transport Area Working Group G. White
Internet-Draft CableLabs
Intended status: Standards Track T. Fossati
Expires: May 7, 2020 ARM
November 4, 2019
A Non-Queue-Building Per-Hop Behavior (NQB PHB) for Differentiated
Services
draft-ietf-tsvwg-nqb-00
Abstract
This document specifies properties and characteristics of a Non-
Queue-Building Per-Hop Behavior (NQB PHB). The purpose of this NQB
PHB is to provide a separate queue that enables low latency and, when
possible, low loss for application-limited traffic flows that would
ordinarily share a queue with capacity-seeking traffic. The PHB
provides low latency and, when possible, low loss without
prioritization and without rate policing, making it suitable for
environments where the use of either these features may be
restricted. The NQB PHB has been developed primarily for use by
access network segments, where queuing delays and queuing loss caused
by Queue-Building protocols are manifested, but its use is not
limited to such segments. In particular, applications to cable
broadband links and mobile network radio and core segments are
discussed. This document defines a standard Differentiated Services
Code Point (DSCP) to identify Non-Queue-Building flows.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 7, 2020.
White & Fossati Expires May 7, 2020 [Page 1]
Internet-Draft Non-Queue-Building PHB November 2019
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 3
3. Overview: Non-Queue Building Flows . . . . . . . . . . . . . 3
4. DSCP Marking of NQB Traffic . . . . . . . . . . . . . . . . . 4
5. Non Queue Building PHB Requirements . . . . . . . . . . . . . 5
6. Relationship to L4S . . . . . . . . . . . . . . . . . . . . . 6
7. Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7.1. DOCSIS Access Networks . . . . . . . . . . . . . . . . . 6
7.2. Mobile Networks . . . . . . . . . . . . . . . . . . . . . 6
7.3. WiFi Networks . . . . . . . . . . . . . . . . . . . . . . 7
8. Open Points . . . . . . . . . . . . . . . . . . . . . . . . . 7
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 7
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
11. Security Considerations . . . . . . . . . . . . . . . . . . . 8
12. Informative References . . . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9
1. Introduction
This document defines a Differentiated Services (DS) per-hop behavior
(PHB) called "Non-Queue-Building Per-Hop Behavior" (NQB PHB), which
is intended to enable networks to provide low latency and low loss
for traffic flows that are relatively low data rate and that do not
themselves materially contribute to queueing delay and loss. Such
Non-Queue-Building flows (for example: interactive voice and video,
gaming, machine to machine applications) are application limited
flows that are distinguished from traffic flows managed by an end-to-
end congestion control algorithm.
The vast majority of packets that are carried by broadband access
networks are, in fact, managed by an end-to-end congestion control
White & Fossati Expires May 7, 2020 [Page 2]
Internet-Draft Non-Queue-Building PHB November 2019
algorithm, such as Reno, Cubic or BBR. These congestion control
algorithms attempt to seek the available capacity of the end-to-end
path (which can frequently be the access network link capacity), and
in doing so generally overshoot the available capacity, causing a
queue to build-up at the bottleneck link. This queue build up
results in queuing delay that the application experiences as variable
latency, and may result in packet loss as well.
In contrast to traditional congestion-controlled applications, there
are a variety of relatively low data rate applications that do not
materially contribute to queueing delay and loss, but are nonetheless
subjected to it by sharing the same bottleneck link in the access
network. Many of these applications may be sensitive to latency or
latency variation, as well as packet loss, and thus produce a poor
quality of experience in such conditions.
Active Queue Management (AQM) mechanisms (such as PIE [RFC8033],
DOCSIS-PIE [RFC8034], or CoDel [RFC8289]) can improve the quality of
experience for latency sensitive applications, but there are
practical limits to the amount of improvement that can be achieved
without impacting the throughput of capacity-seeking applications
when only a few of such flows are present.
The NQB PHB supports differentiating between these two classes of
traffic in bottleneck links and queuing them separately in order that
both classes can deliver satisfactory quality of experience for their
applications.
2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Overview: Non-Queue Building Flows
There are many applications that send traffic at relatively low data
rates and/or in a fairly smooth and consistent manner such that they
are highly unlikely to exceed the available capacity of the network
path between source and sink. These applications do not make
extensive use of network buffers, but nonetheless can be subjected to
packet delay and delay variation as a result of sharing a network
buffer with those that do make use of them. Many of these
applications are negatively affected by excessive packet delay and
delay variation. Such applications are ideal candidates to be queued
White & Fossati Expires May 7, 2020 [Page 3]
Internet-Draft Non-Queue-Building PHB November 2019
separately from the capacity-seeking applications that are the cause
of queue buildup, latency and loss.
These Non-queue-building (NQB) flows are typically UDP flows that
don't seek the capacity of the link (examples: online games, voice
chat, DNS lookups, real-time IoT analytics data). Here the data rate
is essentially limited by the Application itself. In contrast,
Queue-building (QB) flows include traffic which uses the Traditional
TCP or QUIC, with BBR or other TCP congestion controllers.
There are many application flows that fall very neatly into one or
the other of these categories, but there are also application flows
that may be in a gray area in between (e.g. they are NQB on higher-
speed links, but QB on lower-speed links).
Editor's Note: Do we need to answer the following questions? How can
an application determine whether it is queue building or not, given
that the sending application is generally not aware of the available
capacity of the path to the receiving endpoint? Even if the
application were to be aware of the capacity of the path, how could
it be sure that the available capacity (considering other flows that
may be sharing the path) would be sufficient to result in the
application's traffic not causing a queue to form?
4. DSCP Marking of NQB Traffic
This document recommends a DiffServ Code Point (DSCP) of 0x2A to
identify packets of NQB flows. (editor's note: this value is subject
to change)
It is worthwhile to note that the NQB designation and marking is
intended to convey verifiable traffic behavior, not needs or wants.
Also, it is important that incentives are aligned correctly, i.e.
that there is a benefit to the application in marking its packets
correctly, and no benefit to an application in intentionally
mismarking its traffic. Thus, a useful property of nodes that
support separate queues for NQB and QB flows would be that for NQB
flows, the NQB queue provides better performance than the QB queue;
and for QB flows, the QB queue provides better performance than the
NQB queue. By adhering to these principles, there is no incentive
for senders to mismark their traffic as NQB, and further, any
mismarking can be identified by the network.
In contrast to the existing standard DSCPs, which are typically only
meaningful within a DiffServ Domain (e.g. an AS or an enterprise
network), this DSCP is expected to be used end-to-end across the
Internet. Some network operators typically bleach (zero out) the
Diffserv field on ingress into their network [Custura], and in some
White & Fossati Expires May 7, 2020 [Page 4]
Internet-Draft Non-Queue-Building PHB November 2019
cases apply their own DSCP for internal usage. Networks that support
the NQB PHB SHOULD preserve the NQB DSCP when forwarding via an
interconnect from another network.
5. Non Queue Building PHB Requirements
A node supporting the NQB PHB makes no guarantees on latency or data
rate for NQB marked flows, but instead aims to provide a bound on
queuing delay for as many such marked flows as it can, and shed load
when needed.
A node supporting the NQB PHB MUST provide a queue for non-queue-
building traffic separate from the queue used for queue-building
traffic.
NQB traffic SHOULD NOT be rate limited or rate policed separately
from queue-building traffic of equivalent importance.
The NQB queue SHOULD be given equal priority compared to queue-
building traffic of equivalent importance. The node SHOULD provide a
scheduler that allows QB and NQB traffic of equivalent importance to
share the link in a fair manner, e.g. a deficit round-robin scheduler
with equal weights.
A node supporting the NQB PHB SHOULD treat traffic marked as Default
(DSCP=0x00) as QB traffic having equivalent importance to the NQB
marked traffic.
The NQB queue SHOULD have a buffer size that is significantly smaller
than the buffer provided for QB traffic.
It is possible that due to an implementation error or
misconfiguration, a QB flow would end up getting mismarked as NQB, or
vice versa. In the case of an NQB flow that isn't marked as NQB and
ends up in the QB queue, it would only impact its own quality of
service, and so it seems to be of lesser concern. However, a QB flow
that is mismarked as NQB would cause queuing delays for all of the
other flows that are sharing the NQB queue.
To prevent this situation from harming the performance of the real
NQB flows, network elements that support differentiating NQB traffic
SHOULD (editor's note: SHOULD vs MUST is TBD) support a "traffic
protection" function that can identify QB flows that are mismarked as
NQB, and reclassify those flows/packets to the QB queue. Such a
function SHOULD be implemented in an objective and verifiable manner,
basing its decisions upon the behavior of the flow rather than on
application-layer constructs. One example algorithm can be found in
[I-D.briscoe-docsis-q-protection].
White & Fossati Expires May 7, 2020 [Page 5]
Internet-Draft Non-Queue-Building PHB November 2019
6. Relationship to L4S
The dual-queue mechanism described in this draft is intended to be
compatible with [I-D.ietf-tsvwg-l4s-arch], with the result being that
NQB traffic and L4S traffic can share the low-latency queue in an L4S
dual-queue node [I-D.ietf-tsvwg-aqm-dualq-coupled].
7. Use Cases
7.1. DOCSIS Access Networks
Residential cable broadband Internet services are commonly configured
with a single bottleneck link (the access network link) upon which
the service definition is applied. The service definition, typically
an upstream/downstream data rate tuple, is implemented as a
configured pair of rate shapers that are applied to the user's
traffic. In such networks, the quality of service that each
application receives, and as a result, the quality of experience that
it generates for the user is influenced by the characteristics of the
access network link.
To support the NQB PHB, cable broadband services MUST be configured
to provide a separate queue for NQB marked traffic. The NQB queue
MUST be configured to share the service's rate shaping bandwith with
the queue for QB traffic.
7.2. Mobile Networks
Historically, mobile networks have been configured to bundle all
flows to and from the Internet into a single "default" EPS bearer
whose buffering characteristics are not compatible with low-latency
traffic. The established behaviour is rooted partly in the desire to
prioritise operators' voice services over competing over-the-top
services and partly in the fact that the addition of bearers was
prohibitive due to expense. Of late, said consideration seems to
have lost momentum (e.g., with the rise in Multi-RAB (Radio Access
Bearer) devices) and the incentives might now be aligned towards
allowing a more suitable treatment of Internet real-time flows.
To support the NQB PHB, the mobile network MUST be configured to give
UEs a dedicated, low-latency, non-GBR, EPS bearer, e.g. one with QCI
7, in addition to the default EPS bearer; or a Data Radio Bearer with
5QI 7 in a 5G system (see Table 5.7.4-1: Standardized 5QI to QoS
characteristics mapping in [SA-5G]).
A packet carrying the NQB DSCP SHOULD be routed through the dedicated
low-latency EPS bearer. A packet that has no associated NQB marking
SHOULD be routed through the default EPS bearer.
White & Fossati Expires May 7, 2020 [Page 6]
Internet-Draft Non-Queue-Building PHB November 2019
7.3. WiFi Networks
WiFi networking equipment compliant with 802.11e generally supports
either four or eight transmit queues and four sets of associated EDCA
parameters (corresponding to the four WiFi Multimedia Access
Categories) that are used to enable differentiated media access
characteristics. Implementations typically utilize the IP DSCP field
to select a transmit queue, but should be considered as Non-
Differentiated Services-Compliant Nodes as described in Section 4 of
[RFC2475]. As a result this document discusses interoperability with
WiFi networks, as opposed to PHB compliance.
As discussed in [RFC8325], most existing implementations use a
default DSCP to User Priority mapping that utilizes the most
significant three bits of the DiffServ Field to select "User
Priority" which is then mapped to the four WMM Access Categories. In
order to increase the likelihood that NQB traffic is provided a
separate queue from QB traffic in existing WiFi equipment, the 0x2A
codepoint is preferred for NQB. This would map NQB to UP_5 which is
in the "Video" Access Category.
Systems that utilize [RFC8325], SHOULD map the NQB codepoint to UP_5
in the "Video" Access Category.
In order to preserve the incentives principle, WiFi systems SHOULD
configure the EDCA parameters for the Video Access Category to match
those of the Best Effort Access Category.
8. Open Points
o Traffic Protection: SHOULD or MUST?
o Traffic Protection: what are the detailed requirements?
o DSCP value vis a vis WMM: VideoAC or BestEffortAC?
o Are there hidden requirements in Section 9 of the individual
draft?
o Is more discussion needed around applicability in order to give
guidance to application devs?
9. Acknowledgements
Thanks to Bob Briscoe, Greg Skinner, Toke Hoeiland-Joergensen, Luca
Muscariello, David Black, Sebastian Moeller, Ruediger Geib, Jerome
Henry, Steven Blake, Jonathan Morton, Roland Bless, Kevin Smith,
Martin Dolly, and Kyle Rose for their review comments.
White & Fossati Expires May 7, 2020 [Page 7]
Internet-Draft Non-Queue-Building PHB November 2019
10. IANA Considerations
This draft proposes the registration of a standardized DSCP = 0x2A to
denote Non-Queue-Building behavior.
11. Security Considerations
There is no incentive for an application to mismark its packets as
NQB (or vice versa). If a queue-building flow were to mark its
packets as NQB, it could experience excessive packet loss (in the
case that traffic-protection is not supported by a node) or it could
receive no benefit (in the case that traffic-protection is
supported). If a non-queue-building flow were to fail to mark its
packets as NQB, it could suffer the latency and loss typical of
sharing a queue with capacity seeking traffic.
The NQB signal is not integrity protected and could be flipped by an
on-path attacker. This might negatively affect the QoS of the
tampered flow.
12. Informative References
[Custura] Custura, A., Venne, A., and G. Fairhurst, "Exploring DSCP
modification pathologies in mobile edge networks", TMA ,
2017.
[I-D.briscoe-docsis-q-protection]
Briscoe, B. and G. White, "Queue Protection to Preserve
Low Latency", draft-briscoe-docsis-q-protection-00 (work
in progress), July 2019.
[I-D.ietf-tsvwg-aqm-dualq-coupled]
Schepper, K., Briscoe, B., and G. White, "DualQ Coupled
AQMs for Low Latency, Low Loss and Scalable Throughput
(L4S)", draft-ietf-tsvwg-aqm-dualq-coupled-10 (work in
progress), July 2019.
[I-D.ietf-tsvwg-l4s-arch]
Briscoe, B., Schepper, K., Bagnulo, M., and G. White, "Low
Latency, Low Loss, Scalable Throughput (L4S) Internet
Service: Architecture", draft-ietf-tsvwg-l4s-arch-04 (work
in progress), July 2019.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
White & Fossati Expires May 7, 2020 [Page 8]
Internet-Draft Non-Queue-Building PHB November 2019
[RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z.,
and W. Weiss, "An Architecture for Differentiated
Services", RFC 2475, DOI 10.17487/RFC2475, December 1998,
<https://www.rfc-editor.org/info/rfc2475>.
[RFC8033] Pan, R., Natarajan, P., Baker, F., and G. White,
"Proportional Integral Controller Enhanced (PIE): A
Lightweight Control Scheme to Address the Bufferbloat
Problem", RFC 8033, DOI 10.17487/RFC8033, February 2017,
<https://www.rfc-editor.org/info/rfc8033>.
[RFC8034] White, G. and R. Pan, "Active Queue Management (AQM) Based
on Proportional Integral Controller Enhanced PIE) for
Data-Over-Cable Service Interface Specifications (DOCSIS)
Cable Modems", RFC 8034, DOI 10.17487/RFC8034, February
2017, <https://www.rfc-editor.org/info/rfc8034>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8289] Nichols, K., Jacobson, V., McGregor, A., Ed., and J.
Iyengar, Ed., "Controlled Delay Active Queue Management",
RFC 8289, DOI 10.17487/RFC8289, January 2018,
<https://www.rfc-editor.org/info/rfc8289>.
[RFC8325] Szigeti, T., Henry, J., and F. Baker, "Mapping Diffserv to
IEEE 802.11", RFC 8325, DOI 10.17487/RFC8325, February
2018, <https://www.rfc-editor.org/info/rfc8325>.
[SA-5G] 3GPP, "System Architecture for 5G", TS 23.501, 2019.
Authors' Addresses
Greg White
CableLabs
Email: g.white@cablelabs.com
Thomas Fossati
ARM
Email: Thomas.Fossati@arm.com
White & Fossati Expires May 7, 2020 [Page 9]