Authenticated Chunks for the Stream Control Transmission Protocol (SCTP)
draft-ietf-tsvwg-sctp-auth-08
The information below is for an old version of the document that is already published as an RFC.
| Document | Type | RFC Internet-Draft (tsvwg WG) | |
|---|---|---|---|
| Authors | Peter Lei , Randall R. Stewart , Michael Tüxen , Eric Rescorla | ||
| Last updated | 2015-10-14 (Latest revision 2007-02-28) | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text htmlized pdfized bibtex | ||
| Stream | WG state | (None) | |
| Document shepherd | (None) | ||
| IESG | IESG state | RFC 4895 (Proposed Standard) | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | Magnus Westerlund | ||
| Send notices to | mramalho@cisco.com, qxie1@email.mot.com |
draft-ietf-tsvwg-sctp-auth-08
Network Working Group M. Tuexen
Internet-Draft Muenster Univ. of Applied Sciences
Intended status: Standards Track R. Stewart
Expires: August 30, 2007 P. Lei
Cisco Systems, Inc.
E. Rescorla
RTFM, Inc.
February 26, 2007
Authenticated Chunks for Stream Control Transmission Protocol (SCTP)
draft-ietf-tsvwg-sctp-auth-08.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on August 30, 2007.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
This document describes a new chunk type, several parameters and
procedures for SCTP. This new chunk type can be used to authenticate
SCTP chunks by using shared keys between the sender and receiver.
The new parameters are used to establish the shared keys.
Tuexen, et al. Expires August 30, 2007 [Page 1]
Internet-Draft SCTP authentication chunk February 2007
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. New Parameter Types . . . . . . . . . . . . . . . . . . . . . 4
3.1. Random Parameter (RANDOM) . . . . . . . . . . . . . . . . 4
3.2. Chunk List Parameter (CHUNKS) . . . . . . . . . . . . . . 5
3.3. Requested HMAC Algorithm Parameter (HMAC-ALGO) . . . . . . 6
4. New Error Cause . . . . . . . . . . . . . . . . . . . . . . . 7
4.1. Unsupported HMAC Identifier error cause . . . . . . . . . 7
5. New Chunk Type . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1. Authentication Chunk (AUTH) . . . . . . . . . . . . . . . 8
6. Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.1. Establishment of an association shared key . . . . . . . . 10
6.2. Sending authenticated chunks . . . . . . . . . . . . . . . 11
6.3. Receiving authenticated chunks . . . . . . . . . . . . . . 12
7. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14
8.1. A New Chunk Type . . . . . . . . . . . . . . . . . . . . . 15
8.2. Three New Parameter Types . . . . . . . . . . . . . . . . 15
8.3. A New Error Cause . . . . . . . . . . . . . . . . . . . . 15
8.4. A New Table For HMAC Identifiers . . . . . . . . . . . . . 16
9. Security Considerations . . . . . . . . . . . . . . . . . . . 16
10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 17
11. Normative References . . . . . . . . . . . . . . . . . . . . . 17
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 18
Intellectual Property and Copyright Statements . . . . . . . . . . 20
Tuexen, et al. Expires August 30, 2007 [Page 2]
Internet-Draft SCTP authentication chunk February 2007
1. Introduction
SCTP uses 32 bit verification tags to protect itself against blind
attackers. These values are not changed during the lifetime of an
SCTP association.
Looking at new SCTP extensions there is the need to have a method of
proving that an SCTP chunk(s) was really sent by the original peer
that started the association and not by a malicious attacker.
Using TLS as defined in RFC3436 [6] does not help here because it
only secures SCTP user data.
Therefore an SCTP extension is presented which provides a mechanism
for deriving shared keys for each association. These association
shared keys are derived from endpoint pair shared keys, which are
configured and might be empty, and data which is exchanged during the
SCTP association setup.
The extension presented in this document allows an SCTP sender to
authenticate chunks using shared keys between the sender and
receiver. The receiver can then verify that the chunks are sent from
the sender and not from a malicious attacker as long as the attacker
does not know an association shared key.
The extension described in this document puts the result of an HMAC
computation before the data covered by that computation. Putting it
at the end of the packet would have required putting a control chunk
after DATA chunks in case of authenticating DATA chunks. This would
break the rule that control chunks occur before DATA chunks in SCTP
packets. It should also be noted that putting the result of the HMAC
computation after the data being covered would not allow sending the
packet during the computation of the HMAC because the result of the
HMAC computation is needed to compute the CRC32C checksum of the SCTP
packet which is placed in the common header of the SCTP packet.
The SCTP extension for Dynamic Address Reconfiguration (ADD-IP)
requires the usage of the extension described in this document. The
SCTP Partial Reliability Extension (PR-SCTP) can be used in
conjunction with the extension described in this document.
2. Conventions
The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL", when they appear in this document, are to be interpreted
as described in RFC2119 [3].
Tuexen, et al. Expires August 30, 2007 [Page 3]
Internet-Draft SCTP authentication chunk February 2007
3. New Parameter Types
This section defines the new parameter types that will be used to
negotiate the authentication during association setup. Table 1
illustrates the new parameter types.
+----------------+------------------------------------------------+
| Parameter Type | Parameter Name |
+----------------+------------------------------------------------+
| 0x8002 | Random Parameter (RANDOM) |
| 0x8003 | Chunk List Parameter (CHUNKS) |
| 0x8004 | Requested HMAC Algorithm Parameter (HMAC-ALGO) |
+----------------+------------------------------------------------+
Table 1
It should be noted that the parameter format requires the receiver to
ignore the parameter and continue processing if it is not understood.
This is accomplished as described in RFC2960 [5] section 3.2.1. by
the use of the upper bits of the parameter type.
3.1. Random Parameter (RANDOM)
This parameter is used to carry an arbitrary length random number.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Parameter Type = 0x8002 | Parameter Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
\ Random Number /
/ +-------------------------------\
| | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1
Parameter Type: 2 bytes (unsigned integer)
This value MUST be set to 0x8002.
Parameter Length: 2 bytes (unsigned integer)
This value is the length of the Random Number in bytes plus 4.
Random Number: n bytes (unsigned integer)
This value represents an arbitrary Random Number in network byte
order.
Tuexen, et al. Expires August 30, 2007 [Page 4]
Internet-Draft SCTP authentication chunk February 2007
Padding: 0, 1, 2, or 3 bytes (unsigned integer)
If the length of the random number is not a multiple of 4 bytes,
the sender MUST pad the parameter with all zero bytes to make the
parameter 32-bit aligned. The Padding MUST NOT be longer than 3
bytes and it MUST be ignored by the receiver.
The RANDOM parameter MUST be included once in the INIT or INIT-ACK
chunk if the sender wants to send or receive authenticated chunks to
provide a 32 byte Random Number. For 32 byte Random Numbers the
Padding is empty.
3.2. Chunk List Parameter (CHUNKS)
This parameter is used to specify which chunk types are required to
be sent authenticated by the peer.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Parameter Type = 0x8003 | Parameter Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Chunk Type 1 | Chunk Type 2 | Chunk Type 3 | Chunk Type 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
/ /
\ ... \
/ /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Chunk Type n | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2
Parameter Type: 2 bytes (unsigned integer)
This value MUST be set to 0x8003.
Parameter Length: 2 bytes (unsigned integer)
This value is the number of listed Chunk Types plus 4.
Chunk Type n: 1 byte (unsigned integer)
Each Chunk Type listed is required to be authenticated when sent
by the peer.
Padding: 0, 1, 2, or 3 bytes (unsigned integer)
If the number of Chunk Types is not a multiple of 4, the sender
MUST pad the parameter with all zero bytes to make the parameter
32-bit aligned. The Padding MUST NOT be longer than 3 bytes and
it MUST be ignored by the receiver.
Tuexen, et al. Expires August 30, 2007 [Page 5]
Internet-Draft SCTP authentication chunk February 2007
The CHUNKS parameter MUST be included once in the INIT or INIT-ACK
chunk if the sender wants to receive authenticated chunks. Its
maximum length is 260 bytes.
The chunk types for INIT, INIT-ACK, SHUTDOWN-COMPLETE and AUTH chunks
MUST NOT be listed in the CHUNKS parameter. However, if a CHUNKS
parameter is received then the types for INIT, INIT-ACK, SHUTDOWN-
COMPLETE and AUTH chunks MUST be ignored.
3.3. Requested HMAC Algorithm Parameter (HMAC-ALGO)
This parameter is used to list the HMAC identifiers the peer MUST
use.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Parameter Type = 0x8004 | Parameter Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| HMAC Identifier 1 | HMAC Identifier 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
/ /
\ ... \
/ /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| HMAC Identifier n | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3
Parameter Type: 2 bytes (unsigned integer)
This value MUST be set to 0x8004.
Parameter Length: 2 bytes (unsigned integer)
This value is the number of HMAC identifiers multiplied by 2 plus
4.
HMAC Identifier n: 2 bytes (unsigned integer)
The values expressed are a list of HMAC identifiers that may be
used by the peer. The values are listed by preference, with
respect to the sender, where the first HMAC identifier listed is
the one most preferable to the sender.
Padding: 0 or 2 bytes (unsigned integer)
If the number of HMAC Identifiers is not even, the sender MUST pad
the parameter with all zero bytes to make the parameter 32-bit
aligned. The Padding MUST be 0 or 2 bytes long and it MUST be
ignored by the receiver.
Tuexen, et al. Expires August 30, 2007 [Page 6]
Internet-Draft SCTP authentication chunk February 2007
The HMAC-ALGO parameter MUST be included once in the INIT or INIT-ACK
chunk if the sender wants to send or receive authenticated chunks.
The following Table 2 shows the currently defined values for HMAC
identifiers.
+-----------------+--------------------------+
| HMAC Identifier | Message Digest Algorithm |
+-----------------+--------------------------+
| 0 | Reserved |
| 1 | SHA-1 defined in [8] |
| 2 | Reserved |
| 3 | SHA-256 defined in [8] |
+-----------------+--------------------------+
Table 2
Every endpoint supporting SCTP chunk authentication MUST support the
HMAC based on the SHA-1 algorithm.
4. New Error Cause
This section defines a new error cause that will be sent if an AUTH
chunk is received with an unsupported HMAC identifier. Table 3
illustrates the new error cause.
+------------+-----------------------------+
| Cause Code | Error Cause Name |
+------------+-----------------------------+
| 0x0105 | Unsupported HMAC Identifier |
+------------+-----------------------------+
Table 3
4.1. Unsupported HMAC Identifier error cause
This error cause is used to indicate that an AUTH chunk was received
with an unsupported HMAC Identifier.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code = 0x0105 | Cause Length = 6 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| HMAC Identifier | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Tuexen, et al. Expires August 30, 2007 [Page 7]
Internet-Draft SCTP authentication chunk February 2007
Figure 4
Cause Code: 2 bytes (unsigned integer)
This value MUST be set to 0x0105.
Cause Length: 2 bytes (unsigned integer)
This value MUST be set to 6.
HMAC Identifier: 2 bytes (unsigned integer)
This value is the HMAC Identifier which is not supported.
Padding: 2 bytes (unsigned integer)
The sender MUST pad the error cause with all zero bytes to make
the cause 32-bit aligned. The Padding MUST be 2 bytes long and it
MUST be ignored by the receiver.
5. New Chunk Type
This section defines the new chunk type that will be used to
authenticate chunks. Table 4 illustrates the new chunk type.
+------------+-----------------------------+
| Chunk Type | Chunk Name |
+------------+-----------------------------+
| 0x0F | Authentication Chunk (AUTH) |
+------------+-----------------------------+
Table 4
It should be noted that the AUTH-chunk format requires the receiver
to ignore the chunk if it is not understood and silently discard all
chunks that follow. This is accomplished as described in RFC2960 [5]
section 3.2. by the use of the upper bits of the chunk type.
5.1. Authentication Chunk (AUTH)
This chunk is used to hold the result of the HMAC calculation.
Tuexen, et al. Expires August 30, 2007 [Page 8]
Internet-Draft SCTP authentication chunk February 2007
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x0F | Flags=0 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Shared Key Identifier | HMAC Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
\ HMAC /
/ \
/ +-------------------------------\
| | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5
Type: 1 byte (unsigned integer)
This value MUST be set to 0x0F for all AUTH-chunks.
Flags: 1 byte (unsigned integer)
SHOULD be set to zero on transmit and MUST be ignored on receipt.
Length: 2 bytes (unsigned integer)
This value holds the length of the HMAC in bytes plus 8.
Shared Key Identifier: 2 bytes (unsigned integer)
This value describes which endpoint pair shared key is used.
HMAC Identifier: 2 bytes (unsigned integer)
This value describes which message digest is being used. Table 2
shows the currently defined values.
HMAC: n bytes (unsigned integer)
This hold the result of the HMAC calculation.
Padding: 0, 1, 2, or 3 bytes (unsigned integer)
If the length of the HMAC is not a multiple of 4 bytes, the sender
MUST pad the chunk with all zero bytes to make the chunk 32-bit
aligned. The Padding MUST NOT be longer than 3 bytes and it MUST
be ignored by the receiver.
The control chunk AUTH MUST NOT appear more than once in an SCTP
packet. All control and data chunks which are placed after the AUTH
chunk in the packet are sent in an authenticated way. Those chunks
placed in a packet before the AUTH chunk are not authenticated.
Please note that DATA chunks can not appear before control chunks in
an SCTP packet.
Tuexen, et al. Expires August 30, 2007 [Page 9]
Internet-Draft SCTP authentication chunk February 2007
6. Procedures
6.1. Establishment of an association shared key
An SCTP endpoint willing to receive or send authenticated chunks MUST
send one RANDOM parameter in its INIT or INIT-ACK chunk. The RANDOM
parameter MUST contain a 32 byte random number. The random number
should be generated in accordance with RFC4086 [7]. If the random
number is not 32 byte long the association MUST be aborted. The
ABORT chunk SHOULD contain the error cause 'Protocol Violation'. In
case of INIT collision, the rules governing the handling of this
random number follow the same pattern as those for the Verification
Tag, as explained in section 5.2.4 of RFC2960 [5]. Therefore each
endpoint knows its own random number and the peer's random number
after the association has been established.
An SCTP endpoint has a list of chunks it only accepts if they are
received in an authenticated way. This list is included in the INIT
and INIT-ACK and MAY be omitted if it is empty. Since this list does
not change during the lifetime of there is no problem in case of INIT
collision.
Each SCTP endpoint MUST include in the INIT and INIT-ACK a HMAC-ALGO
parameter containing a list of HMAC Identifiers it requests the peer
to use. The receiver of a HMAC-ALGO parameter SHOULD use the first
listed algorithm it supports. The HMAC algorithm based on SHA-1 MUST
be supported and included in the HMAC-ALGO parameter. An SCTP
endpoint MUST NOT change the parameters listed in the HMAC-ALGO
parameter during the lifetime of the endpoint.
Both endpoints of an association MAY have endpoint pair shared keys
which are byte vectors and pre-configured or established by another
mechanism. They are identified by the shared key identifier. For
each endpoint pair shared key an association shared key is computed.
If there is no endpoint pair shared key only one association shared
key is computed by using an empty byte vector as the endpoint pair
shared key.
The RANDOM parameter, the CHUNKS parameter and the HMAC-ALGO
parameter sent by each endpoint are concatenated as byte vectors.
These parameters include the parameter type, parameter length, and
the parameter value, but padding is omitted; all padding MUST be
removed from this concatenation before proceeding with further
computation of keys. Parameters which were not sent are simply
omitted from the concatenation process. The resulting two vectors
are called the two key vectors.
From the endpoint pair shared keys and the key vectors the
Tuexen, et al. Expires August 30, 2007 [Page 10]
Internet-Draft SCTP authentication chunk February 2007
association shared keys are computed. This is performed by selecting
the numerically smaller key vector and concatenating it to the
endpoint pair shared key, and then concatenating the numerically
larger key vector to that. If the key vectors are equal as numbers
but differ in length, then the concatenation order is the endpoint
shared key, followed by the shorter key vector, followed by the
longer key vector. Otherwise, the key vectors are identical, and may
be concatenated to the endpoint pair key in any order. The
concatenation is performed on byte vectors, and all numerical
comparisons use network byte order to convert the key vectors to a
number. The result of the concatenation is the association shared
key.
6.2. Sending authenticated chunks
Endpoints MUST send all requested chunks authenticated where this has
been requested by the peer. The other chunks MAY be sent
authenticated or not. If endpoint pair shared keys are used, one of
them MUST be selected for authentication.
To send chunks in an authenticated way, the sender MUST include these
chunks after an AUTH chunk. This means that a sender MUST bundle
chunks in order to authenticate them.
If the endpoint has no endpoint pair shared key for the peer, it MUST
use Shared Key Identifier 0 with an empty endpoint pair shared key.
If there are multiple endpoint shared keys the sender selects one and
uses the corresponding Shared Key Identifier.
The sender MUST calculate the MAC as described in RFC2104 [2] using
the hash function H as described by the MAC Identifier and the shared
association key K based on the endpoint pair shared key described by
the shared key identifier. The 'data' used for the computation of
the AUTH-chunk is given by the AUTH chunk with its HMAC field set to
zero (as shown in Figure 6) followed by all chunks that are placed
after the AUTH chunk in the SCTP packet.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x0F | Flags=0 | Chunk Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Shared Key Identifier | HMAC Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
\ 0 /
/ +-------------------------------\
| | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Tuexen, et al. Expires August 30, 2007 [Page 11]
Internet-Draft SCTP authentication chunk February 2007
Figure 6
Please note that all fields are in network byte order and that the
field which will contain the complete HMAC is filled with zeroes.
The length of the field shown as 0 is the length of the HMAC
described by the HMAC Identifier. The padding of all chunks being
authenticated MUST be included in the HMAC computation.
The sender fills the HMAC into the HMAC field and sends the packet.
6.3. Receiving authenticated chunks
The receiver has a list of chunk types which it expects to be
received only after an AUTH-chunk. This list has been sent to the
peer during the association setup. It MUST silently discard these
chunks if they are not placed after an AUTH chunk in the packet.
The receiver MUST use the HMAC algorithm indicated in the HMAC
Identifier field. If this algorithm was not specified by the
receiver in the HMAC-ALGO parameter in the INIT or INIT-ACK chunk
during association setup, the AUTH chunk and all chunks after it MUST
be discarded and an ERROR chunk SHOULD be sent with the error cause
defined in Section 4.1.
If an endpoint with no shared key receives a Shared Key Identifier
other than 0, it MUST silently discard all authenticated chunks. If
the endpoint has at least one endpoint pair shared key for the peer,
it MUST use the key specified by the Shared Key Identifier if a key
has been configured for that Shared Key Identifier. If no endpoint
pair shared key has been configured for that Shared Key Identifier,
all authenticated chunks MUST be silently discarded.
The receiver now performs the same calculation as described for the
sender based on Figure 6. If the result of the calculation is the
same as given in the HMAC field, all chunks following the AUTH chunk
are processed. If the field does not match the result of the
calculation, all the chunks following the AUTH chunk MUST be silently
discarded.
It should be noted that if the receiver wants to tear down an
association in an authenticated way only, the handling of malformed
packets should not result in tearing down the association.
An SCTP implementation has to maintain state for each SCTP
association. In the following we call this data structure the SCTP
transmission control block (STCB).
When an endpoint requires COOKIE-ECHO chunks to be authenticated some
Tuexen, et al. Expires August 30, 2007 [Page 12]
Internet-Draft SCTP authentication chunk February 2007
special procedures have to be followed because the reception of an
COOKIE-ECHO chunk might result in the creation of an SCTP
association. If a packet arrives containing an AUTH chunk as a first
chunk, a COOKIE-ECHO chunk as the second chunk and possibly more
chunks after them, and the receiver does not have an STCB for that
packet, then authentication is based on the contents of the COOKIE-
ECHO chunk. In this situation, the receiver MUST authenticate the
chunks in the packet by using the RANDOM parameters, CHUNKS
parameters and HMAC_ALGO parameters obtained from the COOKIE-ECHO
chunk, and possibly a local shared secret as inputs to the
authentication procedure specified in Section 6.3. If authentication
fails then the packet is discarded. If the authentication is
successful the COOKIE-ECHO and all chunks after the COOKIE-ECHO MUST
be processed. If the receiver has a STCB, it MUST process the AUTH
chunk as described above using the STCB from the existing association
to authenticate the COOKIE-ECHO chunk and all chunks after it.
If the receiver does not find a STCB for a packet containing an AUTH
chunk as the first chunk and not a COOKIE-ECHO chunk as the second
chunk, it MUST use the chunks after the AUTH chunk to look up an
existing association. If no association is found, the packet MUST be
considered as out of the blue. The out of the blue handling MUST be
based on the packet without taking the AUTH chunk into account. If
an association is found, it MUST process the AUTH chunk using the
STCB from the existing association as described earlier.
Requiring ABORT chunks and COOKIE-ECHO chunks to be authenticated
makes it impossible for an attacker to bring down or restart an
association as long as the attacker does not know the association
shared key. But it should also be noted that if an endpoint accepts
ABORT chunks only in an authenticated way, it may take longer to
detect that the peer is no longer available. If an endpoint accepts
COOKIE-ECHO chunks only in an authenticated way, the restart
procedure does not work, because the restarting end-point most likely
does not know the association shared key of the old association to be
restarted. However, if the restarting end-point does know the old
association shared key he can send successfully the COOKIE-ECHO chunk
in a way that it is accepted by the peer by using this old
association shared key for the packet containing the AUTH chunk.
After this operation both end-points have to use the new association
shared key.
If a server has an endpoint pair shared key with some clients it can
request the COOKIE_ECHO chunk to be authenticated and can ensure that
only associations from client with a correct endpoint pair shared key
are accepted.
Furthermore it is important that the cookie contained in an INIT-ACK
Tuexen, et al. Expires August 30, 2007 [Page 13]
Internet-Draft SCTP authentication chunk February 2007
chunk and in a COOKIE-ECHO chunk MUST NOT contain any end-point pair
shared keys.
7. Examples
This section gives examples of message exchanges for association
setup.
The simplest way of using the extension described in this document is
given by the following message exchange.
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
Please note that the CHUNKS parameter is optional in the INIT and
INIT-ACK.
If the server wants to receive DATA chunks in an authenticated way,
the following message exchange is possible:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
--------------- COOKIE-ECHO; AUTH; DATA ------------->
<----------------- COOKIE-ACK; SACK ------------------
Please note that if the endpoint pair shared key depends on the
client and the server and that it is only known by the upper layer
this message exchange requires an upper layer intervention between
the processing of the COOKIE-ECHO chunk and the processing of the
AUTH and DATA chunk at the server side. This intervention may be
realized by a COMMUNICATION-UP notification followed by the
presentation of the endpoint pair shared key by the upper layer to
the SCTP stack, see for example section 10 of RFC2960 [5]. If this
intervention is not possible due to limitations of the API (for
example the socket API) the server might discard the AUTH and DATA
chunk making a retransmission of the DATA chunk necessary. If the
same endpoint pair shared key is used for multiple endpoints and does
not depend on the client this intervention might not be necessary.
8. IANA Considerations
[NOTE to RFC-Editor:
Tuexen, et al. Expires August 30, 2007 [Page 14]
Internet-Draft SCTP authentication chunk February 2007
"RFCXXXX" is to be replaced by the RFC number you assign this
document.
]
This document (RFCXXX) is the reference for all registrations
described in this section. All registrations need to be listed in
the document available at sctp-parameters [9]. The suggested changes
are described below.
8.1. A New Chunk Type
A chunk type for the AUTH chunk has to be assigned by IANA. It is
suggested to use the value given in Table 4. This requires an
additional line in the "CHUNK TYPES" table of sctp-parameters [9]:
CHUNK TYPES
ID Value Chunk Type Reference
----- ---------- ---------
15 Authentication Chunk (AUTH) [RFCXXXX]
8.2. Three New Parameter Types
Parameter types have to be assigned for the RANDOM, CHUNKS, and HMAC-
ALGO parameter by IANA. It is suggested to use the values given in
Table 1. This requires two modifications of the "CHUNK PARAMETER
TPYES" tables in sctp-parameters [9]: The first change is the
addition of three new lines to the "INIT Chunk Parameter Types"
table:
Chunk Parameter Type Value
-------------------- -----
Random 32770 (0x8002)
Chunk List 32771 (0x8003)
Requested HMAC Algorithm Parameter 32772 (0x8004)
The second required change is the addition of the same three lines to
the to the "INIT ACK Chunk Parameter Types" table.
8.3. A New Error Cause
An error cause for the Unsupported HMAC Identifier error cause has to
be assigned. It is suggested to use the value given in Table 3.
This requires an additional line of the "CAUSE CODES" table in sctp-
parameters [9]:
Tuexen, et al. Expires August 30, 2007 [Page 15]
Internet-Draft SCTP authentication chunk February 2007
VALUE CAUSE CODE REFERENCE
----- ---------------- ---------
261 (0x0105) Unsupported HMAC Identifier RFCXXXX
8.4. A New Table For HMAC Identifiers
HMAC Identifiers have to be maintained by IANA. Four initial values
should be assigned by IANA as described in Table 2. This requires a
new table "HMAC IDENTIFIERS" in sctp-parameters [9]:
HMAC Identifier Message Digest Algorithm REFERENCE
--------------- ------------------------ ---------
0 Reserved RFCXXXX
1 SHA-1 RFCXXXX
2 Reserved RFCXXXX
3 SHA-256 RFCXXXX
For registering at IANA a new HMAC Identifier in this table a request
has to be made to assign such a number. This number must be unique
and a message digest algorithm usable with the HMAC defined in
RFC2104 [2] MUST be specified. The "Specification Required" policy
of RFC2434 [4] MUST be applied.
9. Security Considerations
Without using endpoint shared keys this extension only protects
against modification or injection of authenticated chunks by
attackers who did not capture the initial handshake setting up the
SCTP association.
If an endpoint pair shared key is used even a true man in the middle
cannot inject chunks which are required to be authenticated even if
he intercepts the initial message exchange. The endpoint also knows
that it is accepting authenticated chunks from a peer who knows the
endpoint pair shared key.
The establishment of endpoint pair shared keys is out of scope of
this document. Other mechanisms can be used like using TLS or manual
configuration.
When an endpoint accepts COOKIE-ECHO chunks only in an authenticated
way the restart procedure does not work. Neither an attacker nor a
restarted end-point not knowing the association shared key can
perform an restart. However, if the association shared key is known,
it is possible to restart the association.
Because SCTP has already a mechanism built-in that handles the
Tuexen, et al. Expires August 30, 2007 [Page 16]
Internet-Draft SCTP authentication chunk February 2007
reception of duplicated chunks, the presented solution makes use of
this functionality and does not provide a method to avoid replay
attacks by itself. Of course, this only works within each SCTP
association. Therefore a separate shared key is used for each SCTP
association to handle replay attacks covering multiple SCTP
associations.
Each endpoint presenting a list of more than one element in the HMAC-
ALGO parameter must be prepared that the peer uses the weakest
algorithm listed.
When an endpoint pair uses non-NULL endpoint pair shared keys and one
of the endpoints still accepts a NULL key an attacker who captured
the initial handshake can still inject or modify authenticated chunks
by using the NULL key.
10. Acknowledgments
The authors wish to thank David Black, Sascha Grau, Russ Housley,
Ivan Arias Rodriguez, Irene Ruengeler, and Magnus Westerlund for
their invaluable comments.
11. Normative References
[1] Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321,
April 1992.
[2] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed-Hashing
for Message Authentication", RFC 2104, February 1997.
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[4] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs", BCP 26, RFC 2434, October 1998.
[5] Stewart, R., Xie, Q., Morneault, K., Sharp, C., Schwarzbauer,
H., Taylor, T., Rytina, I., Kalla, M., Zhang, L., and V. Paxson,
"Stream Control Transmission Protocol", RFC 2960, October 2000.
[6] Jungmaier, A., Rescorla, E., and M. Tuexen, "Transport Layer
Security over Stream Control Transmission Protocol", RFC 3436,
December 2002.
[7] Eastlake, D., Schiller, J., and S. Crocker, "Randomness
Requirements for Security", BCP 106, RFC 4086, June 2005.
Tuexen, et al. Expires August 30, 2007 [Page 17]
Internet-Draft SCTP authentication chunk February 2007
[8] National Institute of Standards and Technology, "Secure Hash
Standard", FIPS PUB 180-2, August 2002,
<http://csrc.nist.gov/publications/fips/fips180-2/
fips180-2.pdf>.
[9] <http://www.iana.org/assignments/sctp-parameters>
Authors' Addresses
Michael Tuexen
Muenster Univ. of Applied Sciences
Stegerwaldstr. 39
48565 Steinfurt
Germany
Email: tuexen@fh-muenster.de
Randall R. Stewart
Cisco Systems, Inc.
4875 Forest Drive
Suite 200
Columbia, SC 29206
USA
Email: rrs@cisco.com
Peter Lei
Cisco Systems, Inc.
8735 West Higgins Road
Suite 300
Chicago, IL 60631
USA
Phone:
Email: peterlei@cisco.com
Tuexen, et al. Expires August 30, 2007 [Page 18]
Internet-Draft SCTP authentication chunk February 2007
Eric Rescorla
RTFM, Inc.
2064 Edgewood Drive
Palo Alto, CA 94303
USA
Phone: +1 650-320-8549
Email: ekr@rtfm.com
Tuexen, et al. Expires August 30, 2007 [Page 19]
Internet-Draft SCTP authentication chunk February 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Tuexen, et al. Expires August 30, 2007 [Page 20]