The Eifel Response Algorithm for TCP
draft-ietf-tsvwg-tcp-eifel-response-06
The information below is for an old version of the document that is already published as an RFC.
| Document | Type | RFC Internet-Draft (tsvwg WG) | |
|---|---|---|---|
| Authors | Andrei Gurtov , Ludwig Reiner | ||
| Last updated | 2015-10-14 (Latest revision 2004-09-15) | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text htmlized pdfized bibtex | ||
| Stream | WG state | (None) | |
| Document shepherd | (None) | ||
| IESG | IESG state | RFC 4015 (Proposed Standard) | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | Jon Peterson | ||
| Send notices to | <mankin@psg.com>, <jon.peterson@neustar.biz> |
draft-ietf-tsvwg-tcp-eifel-response-06
Network Working Group Reiner Ludwig
INTERNET-DRAFT Ericsson Research
Expires: March 2004 Andrei Gurtov
HIIT
September, 2004
The Eifel Response Algorithm for TCP
<draft-ietf-tsvwg-tcp-eifel-response-06.txt>
Status of this memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/lid-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Abstract
Based on an appropriate detection algorithm, the Eifel response
algorithm provides a way for a TCP sender to respond to a detected
spurious timeout. It adapts the retransmission timer to avoid further
spurious timeouts, and can avoid - depending on the detection
algorithm - the often unnecessary go-back-N retransmits that would
otherwise be sent. In addition, the Eifel response algorithm restores
the congestion control state in such a way that packet bursts are
avoided.
Ludwig & Gurtov [Page 1]
INTERNET-DRAFT TCP - Eifel Response September, 2004
Terminology
The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL, when they appear in this
document, are to be interpreted as described in [RFC2119].
We refer to the first-time transmission of an octet as the 'original
transmit'. A subsequent transmission of the same octet is referred to
as a 'retransmit'. In most cases this terminology can likewise be
applied to data segments as opposed to octets. However, when
repacketization occurs, a segment can contain both first-time
transmissions and retransmissions of octets. In that case, this
terminology is only consistent when applied to octets. For the Eifel
detection and response algorithms this makes no difference as they
also operate correctly when repacketization occurs.
We use the term 'acceptable ACK' as defined in [RFC793]. That is an
ACK that acknowledges previously unacknowledged data. We use the term
'bytes_acked' to refer to the amount (in terms of octets) of
previously unacknowledged data that is acknowledged by the most
recently received acceptable ACK. We use the TCP sender state
variables 'SND.UNA' and 'SND.NXT' as defined in [RFC793]. SND.UNA
holds the segment sequence number of the oldest outstanding segment.
SND.NXT holds the segment sequence number of the next segment the TCP
sender will (re-)transmit. In addition, we define as 'SND.MAX' the
segment sequence number of the next original transmit to be sent. The
definition of SND.MAX is equivalent to the definition of 'snd_max' in
[WS95].
We use the TCP sender state variables 'cwnd' (congestion window), and
'ssthresh' (slow-start threshold), and the term 'FlightSize' as
defined in [RFC2581]. We use the term 'Initial Window (IW)' as
defined in [RFC3390]. FlightSize is the amount (in terms of octets)
of outstanding data at a given point in time. The IW is the size of
the sender's congestion window after the three-way handshake is
completed. We use the TCP sender state variables 'SRTT' and 'RTTVAR',
and the terms 'RTO' and 'G' as defined in [RFC2988]. G is the clock
granularity of the retransmission timer. In addition, we assume that
the TCP sender maintains in the (local) variable 'RTT-SAMPLE' the
value of the latest round-trip time (RTT) measurement.
We use the TCP sender state variable 'T_last', and the term 'tcpnow'
as used in [RFC2861]. T_last holds the time when the TCP sender sent
the last data segment while tcpnow is the TCP sender's current
"system time".
1. Introduction
The Eifel response algorithm relies on a detection algorithm such as
the Eifel detection algorithm defined in [RFC3522]. That document
contains informative background and motivation context that may be
Ludwig & Gurtov [Page 2]
INTERNET-DRAFT TCP - Eifel Response September, 2004
useful for implementers of the Eifel response algorithm, but it is
not necessary to read [RFC3522] in order to implement the Eifel
response algorithm. Note that alternative response algorithms have
been proposed [BA02] that could also rely on the Eifel detection
algorithm, and vice versa alternative detection algorithms have been
proposed [RFC3708], [SK04] that could work together with the Eifel
response algorithm.
Based on an appropriate detection algorithm, the Eifel response
algorithm provides a way for a TCP sender to respond to a detected
spurious timeout. It adapts the retransmission timer to avoid further
spurious timeouts, and can avoid - depending on the detection
algorithm - the often unnecessary go-back-N retransmits that would
otherwise be sent. In addition, the Eifel response algorithm restores
the congestion control state in such a way that packet bursts are
avoided.
Note: A previous version of the Eifel response algorithm also
included a response to a detected spurious fast retransmit.
However, since a consensus was not reached about how to adapt the
duplicate acknowledgement threshold in that case, that part of the
algorithm was removed for the time being.
2. Appropriate Detection Algorithms
If the Eifel response algorithm is implemented at the TCP sender, it
MUST be implemented together with a detection algorithm that is
specified in a standards track or experimental RFC.
Designers of detection algorithms who want their algorithms to work
together with the Eifel response algorithm should reuse the variable
"SpuriousRecovery" with the semantics and defined values specified in
[RFC3522]. In addition, we define LATE_SPUR_TO (equal -1) as another
possible value of the variable SpuriousRecovery. Detection algorithms
should set the value of SpuriousRecovery to LATE_SPUR_TO if the
detection of a spurious retransmit is based upon receiving the ACK
for the retransmit (as opposed to an ACK for an original transmit).
For example, this applies to detection algorithms that are based on
the DSACK option [RFC3708].
3. The Eifel Response Algorithm
The complete algorithm is specified in section 3.1. In sections
3.2-3.6, we motivate the different steps of the algorithm.
3.1. The Algorithm
Given that a TCP sender has enabled a detection algorithm that
complies with the requirements set in Section 2, a TCP sender MAY use
the Eifel response algorithm as defined in this subsection.
Ludwig & Gurtov [Page 3]
INTERNET-DRAFT TCP - Eifel Response September, 2004
If the Eifel response algorithm is used, the following steps MUST be
taken by the TCP sender, but only upon initiation of a timeout-based
loss recovery. That is when the first timeout-based retransmit is
sent. I.e., the algorithm MUST NOT be reinitiated after a timeout-
based loss recovery has already started. In particular, it may not be
reinitiated upon subsequent timeouts for the same segment, and not
upon retransmitting segments other than the oldest outstanding
segment.
(0) Before the variables cwnd and ssthresh get updated when
loss recovery is initiated, set a "pipe_prev" variable as
follows:
pipe_prev <- max (FlightSize, ssthresh)
Set a "SRTT_prev" variable and a "RTTVAR_prev" variable as
follows:
SRTT_prev <- SRTT + (2 * G)
RTTVAR_prev <- RTTVAR
(DET) This is a placeholder for a detection algorithm that must
be executed at this point, and that sets the variable
SpuriousRecovery as outlined in Section 2. In case
[RFC3522] is used as the detection algorithm, steps (1) -
(6) of that algorithm go here.
(7) If SpuriousRecovery equals SPUR_TO, then
proceed to step (8),
else if SpuriousRecovery equals LATE_SPUR_TO, then
proceed to step (9),
else
proceed to step (DONE).
(8) Resume the transmission with previously unsent data:
Set
SND.NXT <- SND.MAX
(9) Reversing the congestion control state:
If the acceptable ACK has the ECN-Echo flag [RFC3168] set,
then
proceed to step (DONE),
else set
cwnd <- FlightSize + min (bytes_acked, IW)
ssthresh <- pipe_prev
Proceed to step (DONE).
Ludwig & Gurtov [Page 4]
INTERNET-DRAFT TCP - Eifel Response September, 2004
(10) Interworking with Congestion Window Validation:
If congestion window validation is implemented according
to [RFC2861], then set
T_last <- tcpnow
(11) Adapt the Conservativeness of the Retransmission Timer:
Upon the first RTT-SAMPLE taken from new data, i.e., the
first RTT-SAMPLE that can be derived from an acceptable
ACK for data that was previously unsent when the spurious
timeout occurred,
if the retransmission timer is implemented according
to [RFC2988], then set
SRTT <- max (SRTT_prev, RTT-SAMPLE)
RTTVAR <- max (RTTVAR_prev, RTT-SAMPLE/2)
RTO <- SRTT + max (G, 4*RTTVAR)
Run the bounds check on the RTO (rules (2.4) and
(2.5) in [RFC2988]), and restart the
retransmission timer,
else
Appropriately adapt the conservativeness of the
retransmission timer that is implemented.
(DONE) No further processing.
3.2 Storing the Current Congestion Control State (step 0)
The TCP sender stores in pipe_prev what is considered a safe slow-
start threshold (ssthresh) before loss recovery is initiated, i.e.,
before the loss indication is taken into account. This is either the
current FlightSize if the TCP sender is in congestion avoidance or
the current ssthresh if the TCP sender is in slow-start. If the TCP
sender later detects that it has entered loss recovery unnecessarily,
then pipe_prev is used in step (9) to reverse the congestion control
state. Thus, until the loss recovery phase is terminated, pipe_prev
maintains a memory of the congestion control state of the time right
before the loss recovery phase was initiated. A similar approach is
proposed in [RFC2861], where this state is stored in ssthresh
directly after a TCP sender has become idle or application-limited.
There had been debates about whether the value of pipe_prev should be
decayed over time, e.g., upon subsequent timeouts for the same
outstanding segment. We do not require the decaying of pipe_prev for
the Eifel response algorithm, and do not believe that such a
conservative approach should be in place. Instead, we follow the idea
Ludwig & Gurtov [Page 5]
INTERNET-DRAFT TCP - Eifel Response September, 2004
of revalidating the congestion window through slow-start as suggested
in [RFC2861]. That is, in step (9), the cwnd is reset to a value that
avoids large packet bursts, while ssthresh is reset to the value of
pipe_prev. Note that [RFC2581] and [RFC2861] also do not require a
decaying of ssthresh after it has been reset in response to a loss
indication, or after a TCP sender has become idle or application-
limited.
3.3 Suppressing the Unnecessary go-back-N Retransmits (step 8)
Without the use of the TCP timestamps option [RFC1323], the TCP
sender suffers from the retransmission ambiguity problem [Zh86],
[KP87]. Hence, when the first acceptable ACK arrives after a spurious
timeout, the TCP sender must assume that this ACK was sent in
response to the retransmit when in fact it was sent in response to an
original transmit. Furthermore, the TCP sender must further assume
that all other segments outstanding at that point were lost.
Note: Except for certain cases where original ACKs were lost, the
first acceptable ACK cannot carry a DSACK option [RFC2883].
Consequently, once the TCP sender's state has been updated after the
first acceptable ACK has arrived, SND.NXT equals SND.UNA. This is
what causes the often unnecessary go-back-N retransmits. From that
point on every arriving acceptable ACK that was sent in response to
an original transmit will advance SND.NXT. But as long as SND.NXT is
smaller than the value that SND.MAX had when the timeout occurred,
those ACKs will clock out retransmits, whether those segments were
lost or not.
In fact, during this phase the TCP sender breaks 'packet
conservation' [Jac88]. This is because the go-back-N retransmits are
sent during slow-start. I.e., for each original transmit leaving the
network, two retransmits are sent into the network as long as SND.NXT
does not equal SND.MAX (see [LK00] for more detail).
Once a spurious timeout has been detected (based upon receiving an
ACK for an original transmit), it is therefore safe to let the TCP
sender resume the transmission with previously unsent data. Thus, the
Eifel response algorithm changes the TCP sender's state by setting
SND.NXT to SND.MAX in that case. Note that this step is only executed
if the variable SpuriousRecovery equals SPUR_TO, which in turn
requires a detection algorithm such as the Eifel detection algorithm
[RFC3522] or the F-RTO algorithm [SK04] that detects a spurious
retransmit based upon receiving an ACK for an original transmit (as
opposed to the ACK for the retransmit [RFC3708]).
3.4 Reversing the Congestion Control State (step 9)
When a TCP sender enters loss recovery, it also assumes that is has
received a congestion indication. In response to that it reduces
Ludwig & Gurtov [Page 6]
INTERNET-DRAFT TCP - Eifel Response September, 2004
cwnd, and ssthresh. However, once the TCP sender detects that the
loss recovery has been falsely triggered, this reduction was
unnecessary. In fact, no congestion indication has been received. We
therefore believe that it is safe to revert to the previous
congestion control state following the approach of revalidating the
congestion window as outlined below. This is unless the acceptable
ACK signals congestion through the ECN-Echo flag [RFC3168]. In that
case, the TCP sender MUST refrain from reversing congestion control
state.
If the ECN-Echo flag is not set, cwnd is reset to the sum of the
current FlightSize and the minimum of bytes_acked and IW. Recall that
bytes_acked is the number of bytes that have been acknowledged by the
acceptable ACK. Note that the value of cwnd must not be changed any
further for that ACK, and that the value of FlightSize at this point
in time may be different from the value of FlightSize in step (0).
The value of IW puts a limit on the size of the packet burst that the
TCP sender may send into the network after the Eifel response
algorithm has terminated. The value of IW is considered an acceptable
burst size. It is the amount of data that a TCP sender may send into
a yet "unprobed" network at the beginning of a connection.
Then ssthresh is reset to the value of pipe_prev. As a result, the
TCP sender either immediately resumes probing the network for more
bandwidth in congestion avoidance, or it first slow-starts to what is
considered a safe operating point for the congestion window. In some
cases, this can mean that the first few acceptable ACKs that arrive
will not clock out any data segments.
3.5 Interworking with the CWV Algorithm (step 10)
An implementation of the Congestion Window Validation (CWV) algorithm
[RFC2861] could potentially misinterpret a delay spike that caused a
spurious timeout as a phase where the TCP sender had been idle.
Therefore, T_last is reset to prevent the triggering of the CWV
algorithm in this case.
Note: The term 'idle' implies that the TCP sender has no data
outstanding, i.e., all data sent has been acknowledged [Jac88].
According to this definition, a TCP sender is not idle while it is
waiting for an acceptable ACK after a timeout. Unfortunately, the
pseudo-code in [RFC2861] does not include a check for the
condition "idle" (SND.UNA == SND.MAX). We therefore had to add
step (10) to the Eifel response algorithm.
3.6 Adapting the Retransmission Timer (step 11)
There is currently only one retransmission timer standardized for TCP
[RFC2988]. We therefore only address that timer explicitly. Future
standards that might define alternatives to [RFC2988] should propose
Ludwig & Gurtov [Page 7]
INTERNET-DRAFT TCP - Eifel Response September, 2004
similar measures to adapt the conservativeness of the retransmission
timer.
A spurious timeout often results from a delay spike, which is a
sudden increase of the RTT that usually cannot be predicted. After a
delay spike the RTT may have changed permanently, e.g., due to a path
change, or because the available bandwidth on a bandwidth-dominated
path has decreased. This may often occur with wide-area wireless
access links. In this case, the RTT estimators (SRTT and RTTVAR)
should be reinitialized from the first RTT-SAMPLE taken from new data
according to rule (2.2) of [RFC2988]. That is, from the first RTT-
SAMPLE that can be derived from an acceptable ACK for data that was
previously unsent when the spurious timeout occurred.
However, a delay spike may only indicate a transient phase, after
which the RTT returns to its previous range of values, or even to
smaller values. Also, a spurious timeout may occur because the TCP
sender's RTT estimators were only inaccurate, so that the
retransmission timer expires "a tad too early". We believe that two
times the clock granularity of the retransmission timer (2 * G) is a
reasonable upper bound on "a tad too early". Thus, when the new RTO
is calculated in step (11) we ensure that it is at least (2 * G)
greater (see also step (0)) than the RTO was before the spurious
timeout occurred.
Note that other TCP sender processing will usually take place between
steps (10) and (11). During this phase, i.e., before step (11) has
been reached, the RTO is managed according to the rules of [RFC2988].
We believe that this is sufficiently conservative for the following
reasons. First, the retransmission timer is restarted upon the
acceptable ACK that was used to detect the spurious timeout. As a
result, the delay spike is already implicitly factored in for
segments outstanding at that time. This is discussed in more in
detail in [EL04] where this effect is called the "RTO offset".
Furthermore, if timestamps are enabled, a new and valid RTT-SAMPLE
can be derived from that acceptable ACK. This RTT-SAMPLE must be
relatively large since it includes the delay spike that caused the
spurious timeout. Consequently, the RTT estimators will be updated
rather conservatively. Without timestamps the RTO will stay
conservatively backed-off due to Karn's algorithm [RFC2988] until the
first RTT-SAMPLE that can be derived from an acceptable ACK for data
that was previously unsent when the spurious timeout occurred.
To have the new RTO become effective, the retransmission timer needs
to be restarted. This is consistent with [RFC2988] which recommends
restarting the retransmission timer with the arrival of an acceptable
ACK.
4. Advanced Loss Recovery is Crucial for the Eifel Response Algorithm
Ludwig & Gurtov [Page 8]
INTERNET-DRAFT TCP - Eifel Response September, 2004
We have studied environments where spurious timeouts and multiple
losses from the same flight of packets often coincide [GL02], [GL03].
In such a case the oldest outstanding segment does arrive at the TCP
receiver, but one or more packets from the remaining outstanding
flight are lost. In those environments, TCP-Reno's performance
suffers if the Eifel response algorithm is operated without an
advanced loss recovery scheme such as a SACK-based scheme [RFC3517]
or NewReno [FHG03]. The reason is TCP-Reno's aggressiveness after a
spurious timeout. Even though it breaks 'packet conservation' (see
Section 3.3) when blindly retransmitting all outstanding segments, it
usually recovers all packets lost from that flight within a single
round-trip time. On the contrary, the more conservative
TCP-Reno-with-Eifel is often forced into another timeout. Thus, we
recommend to always operate the Eifel response algorithm in
combination with [RFC3517] or [FHG03]. Additional robustness to
multiple losses from the same flight is achieved with the Limited
Transmit and Early Retransmit algorithms [RFC3042], [AAAB04].
Note: The SACK-based scheme we used for our simulations in [GL02]
and [GL03] is different from the SACK-based scheme that later got
standardized [RFC3517]. The key difference is that [RFC3517] is
more robust to multiple losses from the same flight. It is less
conservative in declaring that a packet has left the network, and
is therefore less dependent on timeouts to recover genuine packet
losses.
In case the NewReno algorithm [FHG03] is used in combination with the
Eifel response algorithm, step 1) of the NewReno algorithm SHOULD be
modified as follows, but only if SpuriousRecovery equals SPUR_TO:
1) Three duplicate ACKs:
When the third duplicate ACK is received and the sender is not
already in the Fast Recovery procedure, go to Step 1A.
That is, the entire step 1B) of the NewReno algorithm is obsolete
because step (8) of the Eifel response algorithm avoids the case
where three duplicate ACKs result from unnecessary go-back-N
retransmits after a timeout. Step (8) of the Eifel response algorithm
avoids such unnecessary go-back-N retransmits in the first place.
However, recall that step (8) is only executed if the variable
SpuriousRecovery equals SPUR_TO, which in turn requires a detection
algorithm such as the Eifel detection algorithm [RFC3522] or the
F-RTO algorithm [SK04] that detects a spurious retransmit based upon
receiving an ACK for an original transmit (as opposed to the ACK for
the retransmit [RFC3708]).
5. IPR Considerations
The IETF has been notified of intellectual property rights claimed in
regard to some or all of the specification contained in this
Ludwig & Gurtov [Page 9]
INTERNET-DRAFT TCP - Eifel Response September, 2004
document. For more information consult the online list of claimed
rights at http://www.ietf.org/ipr.
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
6. Security Considerations
There is a risk that a detection algorithm is fooled by spoofed ACKs
that make genuine retransmits appear to the TCP sender as spurious
retransmits. When such a detection algorithm is run together with the
Eifel response algorithm, this could effectively disable congestion
control at the TCP sender. Should this become a concern, the Eifel
response algorithm SHOULD only be run together with detection
algorithms that are known to be safe against such "ACK spoofing
attacks".
For example, the safe variant of the Eifel detection algorithm
[RFC3522], is a reliable method to protect against this risk.
Acknowledgments
Many thanks to Keith Sklower, Randy Katz, Michael Meyer, Stephan
Baucke, Sally Floyd, Vern Paxson, Mark Allman, Ethan Blanton, Pasi
Sarolahti, Alexey Kuznetsov, and Yogesh Swami for many discussions
that contributed to this work.
Normative References
[RFC2581] Allman, M., Paxson, V. and W. Stevens, TCP Congestion
Control, RFC 2581, April 1999.
[RFC3390] Allman, M., Floyd, S. and C. Partridge, Increasing TCP's
Initial Window, RFC 3390, October 2002.
[RFC2119] Bradner, S., Key words for use in RFCs to Indicate
Requirement Levels, RFC 2119, March 1997.
[FHG03] Floyd, S., Henderson, T. and A. Gurtov, The NewReno
Modification to TCP's Fast Recovery Algorithm, work in
Ludwig & Gurtov [Page 10]
INTERNET-DRAFT TCP - Eifel Response September, 2004
progress, draft-ietf-tsvwg-newreno-02.txt, November 2003.
[RFC2861] Handley, M., Padhye, J. and S. Floyd, TCP Congestion Window
Validation, RFC 2861, June 2000.
[RFC3522] Ludwig, R. and M. Meyer, The Eifel Detection Algorithm for
TCP, RFC3522, April 2003.
[RFC2988] Paxson, V. and M. Allman, Computing TCP's Retransmission
Timer, RFC 2988, November 2000.
[RFC793] Postel, J., Transmission Control Protocol, RFC793,
September 1981.
[RFC3168] Ramakrishnan, K., Floyd, S. and D. Black, The Addition of
Explicit Congestion Notification (ECN) to IP, RFC 3168,
September 2001
Informative References
[RFC3042] Allman, M., Balakrishnan, H. and S. Floyd, Enhancing TCP's
Loss Recovery Using Limited Transmit, RFC 3042,
January 2001.
[AAAB04] Allman, M., Avrachenkov, K., Ayesta, U. and J. Blanton,
Early Retransmit for TCP and SCTP, work in progress,
draft-allman-tcp-early-rexmt-03.txt, December 2003.
[BA02] Blanton, E. and M. Allman, On Making TCP More Robust to
Packet Reordering, ACM Computer Communication Review,
Vol. 32, No. 1, January 2002.
[RFC3708] Blanton, E. and M. Allman, Using TCP Duplicate Selective
Acknowledgements (DSACKs) and SCTP Duplicate Transmission
Sequence Numbers (TSNs) to Detect Spurious Retransmissions,
RFC 3708, February 2004.
[RFC3517] Blanton, E., Allman, M., Fall, K. and L. Wang,
A Conservative SACK-based Loss Recovery Algorithm for TCP,
RFC3517, April 2003.
[EL04] EkstrĂ·m, H. and R. Ludwig, The Peak-Hopper: A New End-to-
End Retransmission Timer for Reliable Unicast Transport, In
Proceedings of IEEE INFOCOM 04, March 2004.
[RFC2883] Floyd, S., Mahdavi, J., Mathis, M., Podolsky, M. and A.
Romanow, An Extension to the Selective Acknowledgement
(SACK) Option for TCP, RFC 2883, July 2000.
[GL02] Gurtov, A. and R. Ludwig, Evaluating the Eifel Algorithm
for TCP in a GPRS Network, In Proceedings of the European
Ludwig & Gurtov [Page 11]
INTERNET-DRAFT TCP - Eifel Response September, 2004
Wireless Conference, February 2002.
[GL03] Gurtov, A. and R. Ludwig, Responding to Spurious Timeouts
in TCP, In Proceedings of IEEE INFOCOM 03, April 2003.
[Jac88] Jacobson, V., Congestion Avoidance and Control, In
Proceedings of ACM SIGCOMM 88.
[RFC1323] Jacobson, V., Braden, R. and D. Borman, TCP Extensions for
High Performance, RFC 1323, May 1992.
[KP87] Karn, P. and C. Partridge, Improving Round-Trip Time
Estimates in Reliable Transport Protocols, In Proceedings
of ACM SIGCOMM 87.
[LK00] Ludwig, R. and R. H. Katz, The Eifel Algorithm: Making TCP
Robust Against Spurious Retransmissions, ACM Computer
Communication Review, Vol. 30, No. 1, January 2000.
[SK04] Sarolahti, P. and M. Kojo, F-RTO: An Algorithm for
Detecting Spurious Retransmission Timeouts with TCP and
SCTP, work in progress, draft-ietf-tcpm-frto-01.txt,
July 2004.
[WS95] Wright, G. R. and W. R. Stevens, TCP/IP Illustrated,
Volume 2 (The Implementation), Addison Wesley,
January 1995.
[Zh86] Zhang, L., Why TCP Timers Don't Work Well, In Proceedings
of ACM SIGCOMM 88.
Author's Address
Reiner Ludwig
Ericsson Research (EED)
Ericsson Allee 1
52134 Herzogenrath, Germany
Email: Reiner.Ludwig@ericsson.com
Andrei Gurtov
Helsinki Institute for Information Technology (HIIT)
P.O. Box 9800, FIN-02015
HUT, Finland
Email: andrei.gurtov@cs.helsinki.fi
Homepage: http://www.cs.helsinki.fi/u/gurtov
This Internet-Draft expires in March 2005.
Ludwig & Gurtov [Page 12]