Autonomic Networking Use Case for Distributed Detection of Service Level Agreement (SLA) Violations
draft-irtf-nmrg-autonomic-sla-violation-detection-13
This document is an Internet-Draft (I-D) that has been submitted to the Internet Research Task Force (IRTF) stream.
This I-D is not endorsed by the IETF and has no formal standing in the
IETF standards process.
The information below is for an old version of the document that is already published as an RFC.
Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 8316.
|
|
---|---|---|---|
Authors | Jéferson Campos Nobre , Lisandro Zambenedetti Granville , Alexander Clemm , Alberto Gonzalez Prieto | ||
Last updated | 2018-12-19 (Latest revision 2017-11-14) | ||
RFC stream | Internet Research Task Force (IRTF) | ||
Intended RFC status | Informational | ||
Formats | |||
IETF conflict review | conflict-review-irtf-nmrg-autonomic-sla-violation-detection | ||
Additional resources | Mailing list discussion | ||
Stream | IRTF state | Published RFC | |
Consensus boilerplate | Yes | ||
Document shepherd | (None) | ||
IESG | IESG state | Became RFC 8316 (Informational) | |
Telechat date | (None) | ||
Responsible AD | (None) | ||
Send notices to | (None) | ||
IANA | IANA review state | IANA OK - No Actions Needed | |
IANA action state | No IANA Actions |
draft-irtf-nmrg-autonomic-sla-violation-detection-13
Network Management Research Group J. Nobre Internet-Draft University of Vale do Rio dos Sinos Intended status: Informational L. Granville Expires: May 19, 2018 Federal University of Rio Grande do Sul A. Clemm Huawei A. Gonzalez Prieto VMware November 15, 2017 Autonomic Networking Use Case for Distributed Detection of SLA Violations draft-irtf-nmrg-autonomic-sla-violation-detection-13 Abstract This document describes an experimental use case for autonomic networking concerning monitoring of Service Level Agreements (SLAs). The use case aims to detect violations of SLAs in a distributed fashion, striving to optimize and dynamically adapt the autonomic deployment of active measurement probes in a way that maximizes the likelihood of detecting service level violations with a given resource budget to perform active measurements, and is able to do so without any outside guidance or intervention. This document is a product of the IRTF Network Management Research Group (NMRG). It is published for informational purposes. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on May 19, 2018. Nobre, et al. Expires May 19, 2018 [Page 1] Internet-Draft AN Use Case Detection of SLA Violations November 2017 Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Definitions and Acronyms . . . . . . . . . . . . . . . . . . 5 3. Current Approaches . . . . . . . . . . . . . . . . . . . . . 6 4. Use Case Description . . . . . . . . . . . . . . . . . . . . 6 5. A Distributed Autonomic Solution . . . . . . . . . . . . . . 7 6. Intended User Experience . . . . . . . . . . . . . . . . . . 10 7. Implementation Considerations . . . . . . . . . . . . . . . . 10 7.1. Device Based Self-Knowledge and Decisions . . . . . . . . 11 7.2. Interaction with other devices . . . . . . . . . . . . . 11 8. Comparison with current solutions . . . . . . . . . . . . . . 11 9. Related IETF Work . . . . . . . . . . . . . . . . . . . . . . 12 10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12 12. Security Considerations . . . . . . . . . . . . . . . . . . . 13 13. Informative References . . . . . . . . . . . . . . . . . . . 13 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 14 1. Introduction The Internet has been growing dramatically in terms of size, capacity, and accessibility in the last years. Communication requirements of distributed services and applications running on top of the Internet have become increasingly demanding. Some examples are real-time interactive video or financial trading. Providing such services involves stringent requirements in terms of acceptable latency, loss, or jitter. Performance requirements lead to the articulation of Service Level Objectives (SLOs) which must be met. Those SLOs are part of Service Level Agreements (SLAs) that define a contract between the provider and the consumer of a service. SLOs, in effect, constitute a service Nobre, et al. Expires May 19, 2018 [Page 2] Internet-Draft AN Use Case Detection of SLA Violations November 2017 level guarantee that the consumer of the service can expect to receive (and often has to pay for). Likewise, the provider of a service needs to ensure that the service level guarantee and associated SLOs are met. Some examples of clauses that relate to service level objectives can be found in [RFC7297]). Violations of SLOs can be associated with significant financial loss, which can by divided into two categories. For one, there is the loss that can be incurred by the user of a service when the agreed service levels are not provided. For example, a financial brokerage's stock orders might suffer losses when it is unable to execute stock transactions in a timely manner. An electronic retailer may lose customers when their online presence is perceived by customers as sluggish. An online gaming provider may not be able to provide fair access to online players, resulting in frustrated players who are lost as customers. In each case, the failure of a service provider to meet promised service level guarantees can have a substantial financial impact on users of the service. By the same token, there is the loss that is incurred by the provider of a service who is unable to meet promised service level objectives. Those losses can take several forms, such as penalties for not meeting the service and, in many cases more important, loss of revenue due to reduced customer satisfaction. Hence, service level objectives are a key concern for the service provider. In order to ensure that SLOs are not being violated, service levels need to be continuously monitored at the network infrastructure layer in order to know, for example, when mitigating actions need to be taken. To that end, service level measurements must take place. Network measurements can be performed using active or passive measurement techniques. In passive measurements, production traffic is observed and no monitoring traffic is created by the measurement process itself. That is, network conditions are checked in a non intrusive way. In the context of IP Flow Information eXport (IPFIX), several documents were produced that define how to export data associated with flow records, i.e. data that is collected as part of passive measurement mechanisms, generally applied against flows of production traffic (e.g., [RFC7011]). In addition, it would be possible to collect real data traffic (not just summarized flow records) with time-stamped packets, possibly sampled (e.g., per [RFC5474], as a means of measuring and inferring service levels. Active measurements, on the other hand, are more intrusive to the network in the sense that it involves injecting synthetic test traffic into the network to measure network service levels, as opposed to simply observing production traffic. The IP Performance Metrics (IPPM) WG produced documents that describe active measurement mechanisms, such as: One-Way Active Measurement Protocol (OWAMP) [RFC4656], Two-Way Active Measurement Protocol (TWAMP) [RFC5357], and Nobre, et al. Expires May 19, 2018 [Page 3] Internet-Draft AN Use Case Detection of SLA Violations November 2017 Cisco Service Level Assurance Protocol (SLA) [RFC6812]. In addition, there are some mechanisms that do not cleanly fit into either active or passive categories, such as Performance and Diagnostic Metrics Destination Option (PDM) techniques [RFC8250]. Active measurement mechanisms offer a high level of control of what and how to measure. They do not require inspecting production traffic. Because of this, active measurements usually offer better accuracy and privacy than passive measurement mechanisms. Traffic encryption and regulations that limit the amount of payload inspection that can occur are non-issues. Furthermore, active measurement mechanisms are able to detect end-to-end network performance problems in a fine-grained way (e.g., simulating the traffic that must be handled considering specific Service Level Objectives - SLOs). As a result, active measurements are often preferred over passive measurement for SLA monitoring. Measurement probes must be hosted in network devices and measurement sessions must be activated to compute the current network metrics (e.g., considering those described in [RFC4148]). This activation should be dynamic in order to follow changes in network conditions, such as those related with routes being added or new customer demands. While offering many advantages, active measurements are expensive in terms of network resource consumption. Active measurements generally involve measurement probes that generate synthetic test traffic that is directed at a responder. The responder needs to timestamp test traffic it receives and reflect it back to the originating measurement probe. The measurement probe subsequently processes the returned packets along with time stamping information in order to compute service levels. Accordingly, active measurements consume substantial CPU cycles as well as memory of network devices to generate and process test traffic. In addition, synthetic traffic increases network load. Active measurements thus compete for resources with other functions, including routing and switching. The resources required and traffic generated by the active measurement sessions are to a large part a function of the number of measured network destinations. (In addition, the amount of traffic generated for each measurement plays a role, which in turn influences the accuracy of the measurement.) The more destinations are being measured, the larger the amount of resources consumed and traffic needed to perform the measurements. Thus, to have a better monitoring coverage it is necessary to deploy more sessions which consequently increases consumed resources. Otherwise, enabling the observation of just a small subset of all network flows can lead to an insufficient coverage. Nobre, et al. Expires May 19, 2018 [Page 4] Internet-Draft AN Use Case Detection of SLA Violations November 2017 Furthermore, while some end-to-end service levels can be determined by adding up the service levels observed across different path segments, the same is not true for all service levels. For example, the end-to-end delay or packet loss from a node A to a node C routed via a node B can often be computed simply by adding delays (or loss) from A to B, and B to C. This allows to decompose a large set of end-to-end measurements into a much smaller set of segment measurements. However, end-to-end jitter and (for example) Mean Opinion Scores cannot be decomposed as easily and, for higher accuracy, must be measured end-to-end. Hence, the decision how to place measurement probes becomes an important management activity. The goal is to obtain maximum benefits of service level monitoring with a limited amount of measurement overhead. Specifically, the goal is to maximize the number of service level violations that are detected with a limited amount of resources. The use case and the solution approach described in this document address an important practical issue. They are intended to provide a basis for further experimentation to lead into solutions for wider deployment. This document represents the consensus of the IRTF's Network Management Research Group (NMRG). It was discussed extensively and received three separate in-depth reviews. 2. Definitions and Acronyms Active Measurements: Techniques to measure service levels that involve generating and observing synthetic test traffic Passive Measurements: Techniques used to measure service levels based on observation of production traffic AN: Autonomic Network; a network containing exclusively autonomic nodes, requiring no configuration and deriving all required information through self-knowledge, discovery, or intent. Autonomic Service Agent (ASA): An agent implemented on an autonomic node that implements an autonomic function, either in part (in the case of a distributed function, as in the context of this document), or whole. Measurement Session: A communications association between a Probe and a Responder used to send and reflect synthetic test traffic for active measurements Probe: The source of synthetic test traffic in an active measurement Nobre, et al. Expires May 19, 2018 [Page 5] Internet-Draft AN Use Case Detection of SLA Violations November 2017 Responder: The destination for synthetic test traffic in an active measurement SLA: Service Level Agreement SLO: Service Level Objective P2P: Peer-to-Peer (Note: definitions of AN and ASA are borrowed from [RFC7575]). 3. Current Approaches The current best practice in feasible deployments of active measurement solutions to distribute the available measurement sessions along the network consists in relying entirely on the human administrator expertise to infer which would be the best location to activate such sessions. This is done through several steps. First, it is necessary to collect traffic information in order to grasp the traffic matrix. Then, the administrator uses this information to infer which are the best destinations for measurement sessions. After that, the administrator activates sessions on the chosen subset of destinations considering the available resources. This practice, however, does not scale well because it is still labor intensive and error-prone for the administrator to determine which sessions should be activated given the set of critical flows that needs to be measured. Even worse, this practice completely fails in networks whose critical flows are too short in time and dynamic in terms of traversing network path, like in modern cloud environments. That is so because fast reactions are necessary to reconfigure the sessions and administrators are just not quick enough in computing and activating the new set of required sessions every time the network traffic pattern changes. Finally, the current active measurements practice usually covers only a fraction of the network flows that should be observed, which invariably leads to the damaging consequence of undetected SLA violations. 4. Use Case Description The use case involves a service level provider who needs to monitor the network to detect service level violations using active service level measurements, and wants to be able to do so with minimal human intervention. The goal is to conduct the measurements in an effective manner maximizing the percentage of detected service level violations. The service level provider has a bounded resource budget with regards to measurements that can be performed, specifically, with regards to the number of measurements that can be conducted concurrently from any one network device, and possibly with regards Nobre, et al. Expires May 19, 2018 [Page 6] Internet-Draft AN Use Case Detection of SLA Violations November 2017 to the total amount of measurement traffic on the network. However, while at any one point in time the number of measurements conducted is limited, it is possible for a device to change which destinations to measure over time. This can be exploited to achieve a balance of eventually covering all possible destinations using a reasonable amount of "sampling" where measurement coverage of a destination cannot be continuous. The solution needs to be dynamic and be able to cope with network conditions which may change over time. The solution should also be embeddable inside network devices that control the deployment of active measurement mechanisms. The goal is to conduct the measurements in a smart manner that ensures that the network is broadly covered and the likelihood of detecting service level violations is maximized. In order to maximize that likelihood, it is reasonable to focus measurement resources on destinations that are more likely to incur a violation, while spending less resources on destinations that are more likely to be in compliance. In order to do so, there are various aspects that can be exploited, including past measurements (destinations close to a service level threshold requiring more focus than destinations further from it), complementation with passive measurements such as flow data (to identify network destinations that are currently popular and critical), and observations from other parts of the network. In addition, measurements can be coordinated among different network devices to avoid hitting the same destination at the same time and to be able to share results that may be useful in future probe placement. Clearly, static solutions will have severe limitations. At the same time, human administrators cannot be in the loop for continuous dynamic measurement probe reconfigurations. Accordingly, an automated or, ideally, autonomic solution is needed in which network measurements are automatically orchestrated and dynamically reconfigured from within the network. This can be accomplished using an autonomic solution that is distributed, using Autonomic Service Agents that are implemented on nodes in the network. 5. A Distributed Autonomic Solution The use of Autonomic Networking (AN) [RFC7575] can help such detection through an efficient activation of measurement sessions. Such an approach, along with a detailed assessment confirming its viability, has been described [P2PBNM-Nobre-2012]. The problem to be solved by AN in the present use case is how to steer the process of Measurement Session activation by a complete solution that sets all necessary parameters for this activation to operate efficiently, reliably and securely, with no required human intervention other than setting overall policy. Nobre, et al. Expires May 19, 2018 [Page 7] Internet-Draft AN Use Case Detection of SLA Violations November 2017 When a node first comes online, it has no information about which measurements are more critical than others. In the absence of information about past measurements and information from measurement peers, it may start with an initial set of measurement sessions, possibly randomly seeding a set of starter measurements, perhaps taking a round robin approach for subsequent measurement rounds. However, as measurements are collected, a node will gain increasing information that it can utilize to refine its strategy of selecting measurement targets going forward. For one, it may take note of which targets returned measurement results very close to service level thresholds that may therefore require closer scrutiny compared to others. Second, it may utilize observations that are made by its measurement peers in order to conclude which measurement targets may be more critical than others, and in order to ensure that proper overall measurement coverage is obtained (so that not every node incidentally measure the same targets, while other targets are not measured at all). We advocate for embedding Peer-to-Peer (P2P) technology in network devices in order to conduct the Measurement Session activation decisions using autonomic control loops. Specifically, we advocate for network devices to implement an autonomic function to monitor service levels for violations of service level objectives, determining which Measurement Sessions to set up at any given point in time based on current and past observations of the node, and of other peer nodes. By performing these functions locally and autonomically on the device itself, which measurements to conduct can be modified quickly based on local observations while taking local resource availability into account. This allows a solution to be more robust and react more dynamically to rapidly changing service levels than a solution that has to rely on central coordination. However, in order to optimize decisions which measurements to conduct, a node will need to communicate with other nodes. This allows a node to take into account other nodes' observations in addition to its own in its decisions. For example, remote destinations whose observed service levels are on the verge of violating stated objectives may require closer monitoring than remote destinations that are comfortably within a range of tolerance. It also allows nodes to coordinate their probing decisions to collectively achieve the best possible measurement coverage. As the amount of resources available for monitoring and for exchange of measurement data and coordination with other nodes are limited, a node may further be interested in identifying other nodes whose observations are most similar to and correlated with its own. This helps a node prioritize and guide with which other nodes Nobre, et al. Expires May 19, 2018 [Page 8] Internet-Draft AN Use Case Detection of SLA Violations November 2017 to primarily coordinate and exchange data with. All of this requires the use of a P2P overlay. A P2P overlay is essential for several reasons: o It makes it possible for nodes (respectively Autonomic Service Agents that are deployed on those nodes) in the network to autonomically set up Measurement Sessions, without having to rely on central management system or controller to perform configuration operations associated with configuring measurement probes and responders. o It facilitates the exchange of data between different nodes to share measurement results so that each node can refine its measurement strategy based not just its own observations, but observations from its peers. o It allows nodes to coordinate their measurements to obtain the best possible test coverage and avoid measurements that have a very low likelihood of detecting service level violations. The provisioning of the P2P overlay should be transparent for the network administrator. An Autonomic Control Plane such as defined in [I-D.anima-autonomic-control-plane] provides an ideal candidate for the P2P overlay to run on. An autonomic solution for the distributed detection of SLA violations provide several benefits. First, efficiency: this solution should optimize the resource consumption and avoid resource starvation on the network devices. A device that is "self-aware" of its available resources will be able to adjust measurement activities rapidly as needed, without requiring a separate control loop involving resource monitoring by an external system. Secondly, placing logic where to conduct measurements in the node enables rapid control loops in which devices are able to react instantly to observations and adjust their measurement strategy. For example, a device could decide to adjust the amount of synthetic test traffic being sent during the measurement itself depending on results observed so far on this and on other concurrent measurement sessions. As a result, the solution could decrease the time necessary to detect SLA violations. Adaptivity features of an autonomic loop could capture faster the network dynamics than an human administrator and even a central controller. Finally, the solution could help to reduce the workload of human administrator, or, at least, to avoid their need to perform operational tasks. In practice, these factors combine to maximize the likelihood of SLA violations being detected while operating within a given resource Nobre, et al. Expires May 19, 2018 [Page 9] Internet-Draft AN Use Case Detection of SLA Violations November 2017 budget, allowing to conduct a continuous measurement strategy that takes into account past measurement results, observations of other measures such as link utilization or flow data, sharing of measurement results between network devices, and coordinating future measurement activities among nodes. Combined this can result in efficient measurement decisions that achieve a golden balance between broad network coverage and honing in on service level "hot spots". 6. Intended User Experience The autonomic solution should not require any human intervention in the distributed detection of SLA violations. By virtue of the solution being autonomic, human users will not have to plan which measurements to conduct in a network, often a very labor intensive task today that requires detailed analysis of traffic matrices and network topologies and is not prone to easy dynamic adjustment. Likewise, they will not have to configure measurement probes and responders. There are some ways in which a human administrator may still interact with the solution. For one, the human administrator will of course be notified and obtain reports about service level violations that are observed. Second, a human administrator may set a policies regarding how closely to monitor the network for service level violations and how many resources to spend. For example, an administrator may set a resource budget that is assigned to network devices for measurement operations. With that given budget, the number of SLO violations that are detected will be maximized. Alternatively, an administrator may set a target for the percentage of SLO violations that must be detected, i.e. a target for the ratio between the number of detected SLO violations, and the number of total SLO violations that are actually occurring (some of which might go undetected). In that case, the solution will aim to minimize the resources spent (i.e. the amount of test traffic and Measurement Sessions) that are required to achieve that target. 7. Implementation Considerations The active measurement model assumes that a typical infrastructure will have multiple network segments and Autonomous Systems (ASs), and a reasonably large number of routers. It also considers that multiple SLOs can be in place at a given time. Since interoperability in a heterogenous network is a goal, features found on different active measurement mechanisms (e.g. OWAMP, TWAMP, and IPSLA) and device programability interfaces (such as Juniper's Junos API or Cisco's Embedded Event Manager) could be used for the implementation. The autonomic solution should include and/or reference specific algorithms, protocols, metrics and technologies Nobre, et al. Expires May 19, 2018 [Page 10] Internet-Draft AN Use Case Detection of SLA Violations November 2017 for the implementation of distributed detection of SLA violations as a whole. Finally, it should be noted that there are multiple deployment scenarios, including deployment scenarios that involve physical devices hosting autonomic functions, or virtualized infrastructure hosting the same. Co-deployment in conjunction with Virtual Network Functions (VNF) is a possibility for further study. 7.1. Device Based Self-Knowledge and Decisions Each device has self-knowledge about the local SLA monitoring. This could be in the form of historical measurement data and SLOs. Besides that, the devices would have algorithms that could decide which probes should be activated in a given time. The choice of which algorithm is better for a specific situation would be also autonomic. 7.2. Interaction with other devices Network devices should share information about service level measurement results. This information can speed up the detection of SLA violations and increase the number of detected SLA violations. For example, if one device detects that a remote destination is in danger of violating an SLO, other devices may conduct additional measurements to the same destination or other destinations in its proximity. For any given network device, the exchange of data may be more important with some devices (for example, devices in the same network neighborhood, or devices that are "correlated" by some other means) than with others. The definition of network devices that exchange measurement data, i.e., management peers, creates a new topology. Different approaches could be used to define this topology (e.g., correlated peers [P2PBNM-Nobre-2012]). To bootstrap peer selection, each device should use its known endpoints neighbors (e.g., FIB and RIB tables) as the initial seed to get possible peers. It should be noted that a solution will benefit if topology information and network discovery functions are provided by the underlying autonomic framework. A solution will need to be able to discover measurement peers as well as measurement targets, specifically measurement targets that support active measurement responders and which will be able to respond to measurement requests and reflect measurement traffic as needed. 8. Comparison with current solutions There is no standardized solution for distributed autonomic detection of SLA violations. Current solutions are restricted to ad hoc scripts running on a per node fashion to automate some Nobre, et al. Expires May 19, 2018 [Page 11] Internet-Draft AN Use Case Detection of SLA Violations November 2017 administrator's actions. There are some proposals for passive probe activation (e.g., DECON and CSAMP), but without the focus on autonomic features. 9. Related IETF Work The following paragraphs discuss related IETF work and are provided for reference. This section is not exhaustive, rather it provides an overview of the various initiatives and how they relate to autonomic distributed detection of SLA violations. 1. [LMAP]: The Large-Scale Measurement of Broadband Performance Working Group aims at the standards for performance management. Since their mechanisms also consist in deploying measurement probes the autonomic solution could be relevant for LMAP specially considering SLA violation screening. Besides that, a solution to decrease the workload of human administrators in service providers is probably highly desirable. 2. [IPFIX]: IP Flow Information EXport (IPFIX) aims at the process of standardization of IP flows (i.e., netflows). IPFIX uses measurement probes (i.e., metering exporters) to gather flow data. In this context, the autonomic solution for the activation of active measurement probes could be possibly extended to address also passive measurement probes. Besides that, flow information could be used in the decision making of probe activation. 3. [ALTO]: The Application Layer Traffic Optimization Working Group aims to provide topological information at a higher abstraction layer, which can be based upon network policy, and with application-relevant service functions located in it. Their work could be leveraged for the definition of the topology regarding the network devices which exchange measurement data. 10. Acknowledgements We wish to acknowledge the helpful contributions, comments, and suggestions that were received from Mohamed Boucadair, Brian Carpenter, Hanlin Fang, Bruno Klauser, Diego Lopez, Vincent Roca, and Eric Voit. In addition, we thank Diego Lopez, Vincent Roca, and Brian Carpenter for their detailed reviews. 11. IANA Considerations This memo includes no request to IANA. Nobre, et al. Expires May 19, 2018 [Page 12] Internet-Draft AN Use Case Detection of SLA Violations November 2017 12. Security Considerations Security of the solution hinges on the security of the network underlay, i.e. the Autonomic Control Plane. If the Autonomic Control Plane were to be compromised, an attacker could undermine the effectiveness of measurement coordination by reporting fraudulent measurement results to peers. This would cause measurement probes to be deployed in an ineffective manner that would increase the likelihood that violations of service level objectives go undetected. Likewise, security of the solution hinges on the security of the deployment mechanism for autonomic functions, in this case, the autonomic function that conducts the service level measurements. If an attacker were able to hijack an autonomic function, it could try to exhaust or exceed the resources that should be spent on autonomic measurements in order to deplete network resources, including network bandwidth due to higher-than-necessary volumes of synthetic test traffic generated by measurement probes. Again, it could also lead to reporting of misleading results, among other things resulting in non-optimal selection of measurement targets and in turn an increase in the likelihood that service level violations go undetected. 13. Informative References [draft-anima-boot] Pritikin, M., Richardson, M., Behringer, M., Bjarnason, S., and K. Watsen, "draft-ietf-anima-bootstrapping- keyinfra", draft-ietf-anima-bootstrapping-keyinfra-08 (work in progress), October 2017. [I-D.anima-autonomic-control-plane] Behringer, M., Eckert, T., and S. Bjarnason, "An Autonomic Control Plane", draft-ietf-anima-autonomic-control- plane-12 (work in progress), October 2017. [P2PBNM-Nobre-2012] Nobre, J., Granville, L., Clemm, A., and A. Gonzalez Prieto, "Decentralized Detection of SLA Violations Using P2P Technology, 8th International Conference Network and Service Management (CNSM)", 2012, <http://ieeexplore.ieee.org/xpls/ abs_all.jsp?arnumber=6379997>. [RFC4148] Stephan, E., "IP Performance Metrics (IPPM) Metrics Registry", BCP 108, RFC 4148, DOI 10.17487/RFC4148, August 2005, <https://www.rfc-editor.org/info/rfc4148>. Nobre, et al. Expires May 19, 2018 [Page 13] Internet-Draft AN Use Case Detection of SLA Violations November 2017 [RFC4656] Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M. Zekauskas, "A One-way Active Measurement Protocol (OWAMP)", RFC 4656, DOI 10.17487/RFC4656, September 2006, <https://www.rfc-editor.org/info/rfc4656>. [RFC5357] Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J. Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)", RFC 5357, DOI 10.17487/RFC5357, October 2008, <https://www.rfc-editor.org/info/rfc5357>. [RFC5474] Duffield, N., Ed., Chiou, D., Claise, B., Greenberg, A., Grossglauser, M., and J. Rexford, "A Framework for Packet Selection and Reporting", RFC 5474, DOI 10.17487/RFC5474, March 2009, <https://www.rfc-editor.org/info/rfc5474>. [RFC6812] Chiba, M., Clemm, A., Medley, S., Salowey, J., Thombare, S., and E. Yedavalli, "Cisco Service-Level Assurance Protocol", RFC 6812, DOI 10.17487/RFC6812, January 2013, <https://www.rfc-editor.org/info/rfc6812>. [RFC7011] Claise, B., Ed., Trammell, B., Ed., and P. Aitken, "Specification of the IP Flow Information Export (IPFIX) Protocol for the Exchange of Flow Information", STD 77, RFC 7011, DOI 10.17487/RFC7011, September 2013, <https://www.rfc-editor.org/info/rfc7011>. [RFC7297] Boucadair, M., Jacquenet, C., and N. Wang, "IP Connectivity Provisioning Profile (CPP)", RFC 7297, DOI 10.17487/RFC7297, July 2014, <https://www.rfc-editor.org/info/rfc7297>. [RFC7575] Behringer, M., Pritikin, M., Bjarnason, S., Clemm, A., Carpenter, B., Jiang, S., and L. Ciavaglia, "Autonomic Networking: Definitions and Design Goals", RFC 7575, DOI 10.17487/RFC7575, June 2015, <https://www.rfc-editor.org/info/rfc7575>. [RFC8250] Elkins, N., Hamilton, R., and M. Ackermann, "IPv6 Performance and Diagnostics Metrics (PDM) Destination Option", RFC 8250, October 2017. Authors' Addresses Nobre, et al. Expires May 19, 2018 [Page 14] Internet-Draft AN Use Case Detection of SLA Violations November 2017 Jeferson Campos Nobre University of Vale do Rio dos Sinos Porto Alegre Brazil Email: jcnobre@unisinos.br Lisandro Zambenedetti Granvile Federal University of Rio Grande do Sul Porto Alegre Brazil Email: granville@inf.ufrgs.br Alexander Clemm Huawei Santa Clara, California USA Email: ludwig@clemm.org Alberto Gonzalez Prieto VMware Palo Alto, California USA Email: agonzalezpri@vmware.com Nobre, et al. Expires May 19, 2018 [Page 15]