NETCONF Private Candidates
draft-jgc-netconf-privcand-01
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Replaced".
|
|
|---|---|---|---|
| Authors | James Cumming , Robert Wills | ||
| Last updated | 2023-03-29 | ||
| Replaced by | draft-ietf-netconf-privcand | ||
| RFC stream | (None) | ||
| Formats | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-jgc-netconf-privcand-01
Internet Engineering Task Force JG. Cumming
Internet-Draft Nokia
Intended status: Standards Track R. Wills
Expires: 30 September 2023 Cisco Systems
29 March 2023
NETCONF Private Candidates
draft-jgc-netconf-privcand-01
Abstract
This document provides a mechanism to extend the Network
Configuration Protocol (NETCONF) to support multiple clients making
configuration changes simultaneously and ensuring that they commit
only those changes that they defined.
This document addresses two specific aspects: The interaction with a
private candidate over the NETCONF protocol and the methods to
identify and resolve conflicts between clients.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 30 September 2023.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
Cumming & Wills Expires 30 September 2023 [Page 1]
Internet-Draft NETCONF Private Candidates March 2023
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. Definitions and terminology . . . . . . . . . . . . . . . . . 3
2.1. Session specific datastore . . . . . . . . . . . . . . . 3
2.2. Shared candidate configuration . . . . . . . . . . . . . 3
2.3. Private candidate configuration . . . . . . . . . . . . . 4
3. Limitations using the shared candidate configuration for
multiple clients . . . . . . . . . . . . . . . . . . . . 4
3.1. Issues . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1.1. Unintended deployment of alternate users configuration
changes . . . . . . . . . . . . . . . . . . . . . . . 4
3.2. Current mitigation strategies . . . . . . . . . . . . . . 5
3.2.1. Locking the shared candidate configuration
datastore . . . . . . . . . . . . . . . . . . . . . . 5
3.2.2. Always use the running configuration datastore . . . 5
3.2.3. Fine-grained locking . . . . . . . . . . . . . . . . 5
4. Private candidates solution . . . . . . . . . . . . . . . . . 6
4.1. What is a private candidate . . . . . . . . . . . . . . . 6
4.2. When is a private candidate created . . . . . . . . . . . 6
4.3. How to signal the use of private candidates . . . . . . . 7
4.3.1. Server . . . . . . . . . . . . . . . . . . . . . . . 7
4.3.2. Client . . . . . . . . . . . . . . . . . . . . . . . 7
4.4. Interaction between running and private-candidate(s) . . 9
4.4.1. Static branch mode: Independent private candidate
branch . . . . . . . . . . . . . . . . . . . . . . . 10
4.4.2. Continuous rebase mode: Continually updating private
candidate . . . . . . . . . . . . . . . . . . . . . . 10
4.5. Detecting and resolving conflicts . . . . . . . . . . . . 11
4.5.1. What is a conflict? . . . . . . . . . . . . . . . . . 11
4.5.2. Detecting and reporting conflicts . . . . . . . . . . 12
4.5.3. Conflict resolution . . . . . . . . . . . . . . . . . 12
4.6. NETCONF operations . . . . . . . . . . . . . . . . . . . 19
4.6.1. New NETCONF operations . . . . . . . . . . . . . . . 20
4.6.2. Updated NETCONF operations . . . . . . . . . . . . . 20
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22
6. Security Considerations . . . . . . . . . . . . . . . . . . . 22
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1. Normative References . . . . . . . . . . . . . . . . . . 22
7.2. Informative References . . . . . . . . . . . . . . . . . 23
Appendix A. Behavior with unaltered NETCONF operations . . . . . 23
A.1. <get> . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cumming & Wills Expires 30 September 2023 [Page 2]
Internet-Draft NETCONF Private Candidates March 2023
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 23
1. Introduction
NETCONF [RFC6241] provides a mechanism for one or more clients to
make configuration changes to a device running as a NETCONF server.
Each NETCONF client has the ability to make one or more configuration
change to the servers shared candidate configuration.
As the name shared candidate suggests, all clients have access to the
same candidate configuration. This means that multiple clients may
make changes to the shared candidate prior to the configuration being
committed. This behavior may be undesirable as one client may
unwittingly commit the configuration changes made by another client.
NETCONF provides a way to mitigate this behavior by allowing clients
to place a lock on the shared candidate. The placing of this lock
means that no other client may make any changes until that lock is
released. This behavior is, in many situations, also undesirable.
Many network devices already support private candidates
configurations, where a user (machine or otherwise) is able to edit a
personal copy of a devices configuration without blocking other users
from doing so.
This document details the extensions to the NETCONF protocol in order
to support the use of private candidates.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Definitions and terminology
2.1. Session specific datastore
A session specific datastore is a configuration datastore that,
unlike the candidate and running configuration datastores which have
only one per system, is bound to the specific NETCONF session.
2.2. Shared candidate configuration
The candidate configuration datastore defined in [RFC6241] is
referenced as the shared candidate configuration in this document.
Cumming & Wills Expires 30 September 2023 [Page 3]
Internet-Draft NETCONF Private Candidates March 2023
2.3. Private candidate configuration
A private candidate configuration is a session specific candidate
configuration datastore.
The specific NETCONF session (and user) that created the private
candidate configuration is the only session (user) that has access to
it over NETCONF. Devices may expose this to other users through
other interfaces but this is out of scope for this document.
The private candidate configuration contains a full copy of the
running configuration when it is created (in the same way as a branch
does in a source control management system and in the same way as the
candidate configuration datastore as defined in [RFC6241]). Any
changes made to it, for example, through the use of operations such
as <edit-config> and <edit-data>, are made in this private candidate
configuration.
Obtaining this private candidate over NETCONF will display the entire
configuration, including all changes made to it. Performing a
<commit> operation will merge the changes from the private candidate
into the running configuration (the same as a merge in source code
management systems). A <discard-changes> operation will revert the
private candidate to the branch's initial state.
All changes made to this private candidate configuration are held
separately from any other candidate configuration changes, whether
made by other users to the shared candidate or any other private
candidate, and are not visible to or accessible by anyone else.
3. Limitations using the shared candidate configuration for multiple
clients
The following sections describe some limitations and mitigation
factors in more detail for the use of the shared candidate
configuration during multi-client configuration over NETCONF.
3.1. Issues
3.1.1. Unintended deployment of alternate users configuration changes
Consider the following scenario:
1. Client 1 modifies item A in the shared candidate configuration
2. Client 2 then modifies item B in the shared candidate
configuration
Cumming & Wills Expires 30 September 2023 [Page 4]
Internet-Draft NETCONF Private Candidates March 2023
3. Client 2 then issues a <commit> RPC
In this situation, both client 1 and client 2 configurations will be
committed by client 2. In a machine-to-machine environment client 2
may not have been aware of the change to item A and, if they had been
aware, may have decided not to proceed.
3.2. Current mitigation strategies
3.2.1. Locking the shared candidate configuration datastore
In order to resolve unintended deployment of alternate users
configuration changes as described above NETCONF provides the ability
to lock a datastore in order to restrict other users from editing and
committed changes.
This does resolve the specific issue above, however, it introduces
another issue. Whilst one of the clients holds a lock, no other
client may edit the configuration. This will result in the client
failing and having to retry. Whilst this may be a desirable
consequence when two clients are editing the same section of the
configuration, where they are editing different sections this
behavior may hold up valid operational activity.
Additionally, a lock placed on the shared candidate configuration
must also lock the running configuration, otherwise changes committed
directly into the running datastore may conflict.
3.2.2. Always use the running configuration datastore
The use of the running configuration datastore as the target for all
configuration changes does not resolve any issues regarding blocking
of system access in the case a lock is taken, nor does it provide a
solution for multiple NETCONF clients as each configuration change is
applied immediately and the client has no knowledge of the current
configuration at the point in time that they commenced the editing
activity nor at the point they commit the activity.
3.2.3. Fine-grained locking
[RFC5717] describes a partial lock mechanism that can be used on
specific portions of the shared candidate datastore.
Partial locking does not solve the issues of staging a set of
configuration changes such that only those changes get committed in a
commit operation, nor does it solve the issue of multiple clients
editing the same parts of the configuration at the same time.
Cumming & Wills Expires 30 September 2023 [Page 5]
Internet-Draft NETCONF Private Candidates March 2023
Partial locking additionally requires that the client is aware of any
interdependencies within the servers YANG models in order to lock all
parts of the tree.
4. Private candidates solution
The use of NETCONF private candidates resolves the issues detailed
earlier in this document.
NETCONF sessions are able to utilize the concept of private
candidates in order to streamline network operations, particularly
for machine-to-machine communication.
Using this approach clients may improve their performance and reduce
the likelihood of blocking other clients from continuing with valid
operational activities.
One or more private candidates may exist at any one time, however, a
private candidate SHOULD:
* Be accessible by one client only
* Be visible by one client only
Additionally, the choice of using a shared candidate configuration
datastore or a private candidate configuration datastore MUST be for
the entire duration of the NETCONF session.
4.1. What is a private candidate
A private candidate is defined earlier in the definitions and
terminology section of this document.
4.2. When is a private candidate created
A private candidate datastore is created when the first RPC that
requires access to it is sent to the server. This could be, for
example, an <edit-config>.
When the private candidate is created a copy of the running
configuration is made and stored in it. This can be considered the
same as creating a branch in a source code repository.
Cumming & Wills Expires 30 September 2023 [Page 6]
Internet-Draft NETCONF Private Candidates March 2023
+----------------------------> private candidate
/
/
+------+-------------------------------> running configuration
^
Private candidate created
Closing a session that is operating using a private candidate will
discard all changes in that session's private candidate and destroy
the private candidate.
4.3. How to signal the use of private candidates
In order to utilise a private candidate configuration, the client
must inform the server that it wishes to do this.
4.3.1. Server
The server MUST signal its support for private candidates. The
server does this by advertising the :candidate capability as defined
in [RFC6241] and a new :private-candidate capability:
urn:ietf:params:netconf:capability:private-candidate:1.0
If the server has not signalled these capabilities, or has signalled
the support for :candidate but not :private-candidate, or :private-
candidate but not :candidate the session MUST be terminated when a
client attempts to interact with a private candidate (for example, by
explicitly targeting the private-candidate NMDA datastore).
4.3.2. Client
Two approaches are available for the client to signal that it wants
to use a private candidate:
4.3.2.1. Client capability declaration
When a NETCONF client connects with a server it sends a list of
client capabilities including one of the :base NETCONF version
capabilties.
In order to enable private candidate mode for the duration of the
NETCONF client session the NETCONF client sends the following
capability:
urn:ietf:params:netconf:capability:private-candidate:1.0
Cumming & Wills Expires 30 September 2023 [Page 7]
Internet-Draft NETCONF Private Candidates March 2023
In order for the use of private candidates to be established both the
NETCONF server and the NETCONF client MUST advertise this capability.
When a server receives the client capability its mode of operation
will be set to private candidate mode for the duration of the NETCONF
session.
All RPC requests that target the candidate configuration datastore
will operate in exactly the same way as they would do when using the
shared candidate configuration datastore, however, when the server
receives a request to act upon the candidate configuration datastore
it instead uses the session's private candidate configuration
datastore.
Using this method, the use of private candidates can be made
available to NMDA and non-NMDA capable servers.
No protocol extensions are required for the transitioning of
candidates between the shared mode and the private mode and no
extensions are required for any RPCs (including <lock>)
4.3.2.2. Private candidate datastore
The private candidate configuration datastore is exposed as its own
datastore similar to other NMDA [RFC8342] capable datastores. This
datastore is called private-candidate.
All NMDA operations that support candidate NMDA datastore SHOULD
support the private-candidate datastore.
Any non-NMDA aware NETCONF operations that take a source or target
(destination) may be extended to accept the new datastore.
The ability for the NETCONF server to support private candidates is
optional and SHOULD be signalled in NMDA supporting servers as a
datastore in addition to the server capabilities described earlier in
this document.
The first datastore referenced (either candidate or private-
candidate) in any NETCONF operation will define which mode that
NETCONF session will operate in for its duration. As an example,
performing a <get-data> operation on the private-candidate datastore
will switch the session into private candidate configuration mode and
subsequent <edit-config> operations that reference the candidate
configuration datastore will fail.
Cumming & Wills Expires 30 September 2023 [Page 8]
Internet-Draft NETCONF Private Candidates March 2023
4.4. Interaction between running and private-candidate(s)
Multiple NETCONF operations may be performed on the private candidate
in order to stage changes ready for a commit.
In the simplest example, a session may create a private candidate
configuration, perform multiple NETCONF operations (such as <edit-
config>) on it and then perform a <commit> operation to merge the
private candidate configuration into the running configuration in
line with semantics in [RFC6241].
commit
+--------------------------+--------> private candidate
/ ^ ^ \
/ edit-config edit-config U+2304
+---+-------------------------------+------> running configuration
^
edit-config
(Private candidate created)
More complex scenarios need to be considered, when multiple private
candidate sessions are working on their own configuration (branches)
and they make commits into the running configuration.
commit
+---------------------+----------------> private candidate 1
/ \
/ edit-config ⌄
+---+------------+-------------+--------------> running configuration
edit-config \
\
+-------------------------> private candidate 2
In this situation, if, how and when private candidate 2 is updated
with the information that the running configuration has changed must
be considered.
As described earlier, the client MUST be aware of changes to the
running configuration so it can be assured that it is only committing
its own modifications.
It is possible, during an update, for conflicts to occur and the
detection and resolution of these is discussed later in this
document.
Cumming & Wills Expires 30 September 2023 [Page 9]
Internet-Draft NETCONF Private Candidates March 2023
Two modes of operation are provided. Both modes may be supported,
however, the server SHOULD advertise which approach is being used in
a capability.
4.4.1. Static branch mode: Independent private candidate branch
The private candidate is treated as a separate branch and changes
made to the running configuration are not placed into the private
candidate datastore except in one of the following situations:
* The client requests that the private candidate be refreshed using
a new <update> operation
* <commit> is issued (which SHOULD automatically issue an <update>
operation)
This approach is similar to the standard approach for source code
management systems.
In this model of operation it is possible for the private candidate
configuration to become significantly out of sync with the running
configuration should the private candidate be open for a long time
without an operation being sent that causes a resync (rebase in
source code control terminology).
A <compare> operation may be performed against the initial starting
point (head) of the private candidates branch or against the running
configuration.
Conflict detection and resolution is discussed later in this
document.
4.4.2. Continuous rebase mode: Continually updating private candidate
The private candidate is treated as a separate branch, however, when
changes are made to the running configuration the update operation
will automatically be run on all open private candidate branches.
This is equivalent to all currently open private candidate branches
being rebased onto the running configuration every time a change is
made to it by any session.
In this model of operation the following should be considered:
Cumming & Wills Expires 30 September 2023 [Page 10]
Internet-Draft NETCONF Private Candidates March 2023
* Because the private candidate is automatically re-synchronized
(rebased) with the running configuration each time a change is
made in the running configuration, the NETCONF session is unaware
that their private candidate configuration has changed unless they
perform one of the get operations on the private candidate and
analyse it for changes.
* A <compare> operation may be performed against the initial
starting point (head) of the private candidates branch or against
the running configuration but these will both report the same
results as the starting point is continually reset.
* The output of the <compare> operation may not match the set of
changes made to the session's private candidate but may include
different output due to the changes in the running configuration
made by other sessions.
* A conflict may occur in the automatic update process pushing
changes from the running configuration into the private candidate.
Conflict detection and resolution is discussed later in this
document.
4.5. Detecting and resolving conflicts
4.5.1. What is a conflict?
A conflict is when the intent of the NETCONF client may have been
different had it had a different starting point. In configuration
terms, a conflict occurs when the same set of nodes in a
configuration being altered by one user are changed between the start
of the configuration preparation (the first <edit-config>/<edit-data>
operation) and the conclusion of this configuration session
(terminated by a <commit> operation).
The situation where conflicts have the potential of occurring are
when multiple configuration sessions are in progress and one session
commits changes into the running configuration after the private
candidate (branch) was created.
When this happens a conflict occurs if the nodes modified in the
running configuration are the same nodes that are modified in the
private candidate configuration.
Examples of conflicts include:
Cumming & Wills Expires 30 September 2023 [Page 11]
Internet-Draft NETCONF Private Candidates March 2023
* An interface has been deleted in the running configuration that
existed when the private candidate was created. A change to a
child node of this specific interface is made in the private
candidate using the default merge operation would, instead of
changing the child node, both recreate the interface and then set
the child node.
* A leaf has been modified in the running configuration from the
value that it had when the private candidate was created. The
private candidate configuration changes that leaf to another
value.
4.5.2. Detecting and reporting conflicts
A conflict can occur when an <update> operation is triggered. This
can occur in a number of ways:
* Manually triggered by the <update> NETCONF operation
* Automatically triggered by the NETCONF server running an <update>
operation upon a <commit> being issued by the client in the
private candidate session.
* Automatically triggered by the NETCONF server running an <update>
operation upon a <commit> being issued by any other configuration
session (or user). This occurs in continual rebase mode only.
When a conflict occurs the client MUST be given the opportunity to
re-evaluate its intent based on the new information. The resolution
of the conflict may be manual or automatic depending on the server
and client decision (discussed later in this document).
When a conflict occurs, a <commit> or <update> operation MUST fail.
It MUST inform the client of the conflict and SHOULD detail the
location of the conflict(s).
In continuous rebase mode, it is possible for the automated <update>
operation to fail. In this instance, the next NETCONF operation (of
any type) MUST fail. It MUST inform the client of the conflict and
SHOULD detail the location of the conflict(s).
The location of the conflict(s) should be reported as a list of
xpaths and values.
4.5.3. Conflict resolution
When a conflict is detected, the client MUST be informed. The client
then has a number of options available to resolve the conflict.
Cumming & Wills Expires 30 September 2023 [Page 12]
Internet-Draft NETCONF Private Candidates March 2023
It is worth noting that in the case of continuous rebase mode
automated <update> operations may be performed against multiple
private candidate configurations at once.
The resolution method SHOULD be provided as an input to the <update>
operation described later in this document. This input may be
through a default selection, a specific input or a configuration
element.
The following configuration data is used below to describe the
behavior of each resolution method:
<configure>
<interfaces>
<interface>
<name>intf_one</name>
<description>Link to London<description>
</interface>
<interface>
<name>intf_two</name>
<description>Link to Tokyo<description>
</interface>
</interfaces>
</configure>
The following workflow diagram is used and the outcome is the same
regardless of whether static branch mode or continuous rebase mode is
being used. For the purpose of the examples below assume the update
operation is manually provided by a client.
update commit
+--------------------+---+------> private candidate 1
/ / \
/ edit-config / ⌄
+---+--------+--------+--+--------+----> running configuration
edit-config \ ^
\ /
+---+------------------> private candidate 2
commit
There are three defined resolution methods:
Cumming & Wills Expires 30 September 2023 [Page 13]
Internet-Draft NETCONF Private Candidates March 2023
4.5.3.1. Ignore
When using the ignore resolution method items in the running
configuration that are not in conflict with the private candidate
configuration are merged from the running configuration into the
private candidate configuration. Nodes that are in conflict are
ignored and not merged. The outcome of this is that the private
candidate configuration reflects changes in the running that were not
being worked on and those that are being worked on in the private
candidate remain in the private candidate. Issuing a <commit>
operation at this point will overwrite the running configuration with
the conflicted items from the private candidate configuration.
Example:
Session 1 edits the configuration by submitting the following
<rpc message-id="config"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<edit-config>
<target><candidate/><target>
<config>
<configure>
<interfaces>
<interface>
<name>intf_one</name>
<description>Link to San Francisco<description>
</interface>
</interfaces>
</configure>
</config>
</edit-config>
</rpc>
Session 2 then edits the configuration deleting the interface
intf_one, updating the description on interface intf_two and
committing the configuration to the running configuration datastore.
Cumming & Wills Expires 30 September 2023 [Page 14]
Internet-Draft NETCONF Private Candidates March 2023
<rpc message-id="config"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<edit-config>
<target><candidate/><target>
<config>
<configure>
<interfaces>
<interface>
<name operation="delete">intf_one</name>
</interface>
<interface>
<name>intf_two</name>
<description>Link moved to Paris</description>
</interface>
</interfaces>
</configure>
</config>
</edit-config>
</rpc>
Session 1 then sends an <update> NETCONF operation.
<rpc message-id="update"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<update>
<resolution-mode>ignore</resolution-mode>
</update>
</rpc>
The un-conflicting changes are merged and the conflicting ones are
ignored (and not merged from the running into private candidate 1).
The resulting data in private candidate 1 is:
<configure>
<interfaces>
<interface>
<name>intf_one</name>
<description>Link to San Francisco<description>
</interface>
<interface>
<name>intf_two</name>
<description>Link moved to Paris<description>
</interface>
</interfaces>
</configure>
Cumming & Wills Expires 30 September 2023 [Page 15]
Internet-Draft NETCONF Private Candidates March 2023
4.5.3.2. Overwrite
When using the overwrite resolution method items in the running
configuration that are not in conflict with the private candidate
configuration are merged from the running configuration into the
private candidate configuration. Nodes that are in conflict are
pushed from the running configuration into the private candidate
configuration, overwriting any previous changes in the private
candidate configuration. The outcome of this is that the private
candidate configuration reflects the changes in the running
configuration that were not being worked on as well as changing those
being worked on in the private candidate to new values.
Example:
Session 1 edits the configuration by submitting the following
<rpc message-id="config"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<edit-config>
<target><candidate/><target>
<config>
<configure>
<interfaces>
<interface>
<name>intf_one</name>
<description>Link to San Francisco<description>
</interface>
</interfaces>
</configure>
</config>
</edit-config>
</rpc>
Session 2 then edits the configuration deleting the interface
intf_one, updating the description on interface intf_two and
committing the configuration to the running configuration datastore.
Cumming & Wills Expires 30 September 2023 [Page 16]
Internet-Draft NETCONF Private Candidates March 2023
<rpc message-id="config"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<edit-config>
<target><candidate/><target>
<config>
<configure>
<interfaces>
<interface>
<name operation="delete">intf_one</name>
</interface>
<interface>
<name>intf_two</name>
<description>Link moved to Paris</description>
</interface>
</interfaces>
</configure>
</config>
</edit-config>
</rpc>
Session 1 then sends an <update> NETCONF operation.
<rpc message-id="update"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<update>
<resolution-mode>overwrite</resolution-mode>
</update>
</rpc>
The un-conflicting changes are merged and the conflicting ones are
pushed into the private candidate 1 overwriting the existing changes.
The resulting data in private candidate 1 is:
<configure>
<interfaces>
<interface>
<name>intf_two</name>
<description>Link moved to Paris<description>
</interface>
</interfaces>
</configure>
4.5.3.3. Revert-on-conflict
When using the revert-on-conflict resolution method items and update
will fail to complete when any conflicting node is found. The
session issuing the update will be informed of the failure.
Cumming & Wills Expires 30 September 2023 [Page 17]
Internet-Draft NETCONF Private Candidates March 2023
No changes, whether conflicting or un-conflicting are merged into the
private candidate configuration.
The owner of the private candidate session must then take deliberate
and specific action to adjust the private candidate configuration to
rectify the conflict. This may be by issuing further <edit-config>
or <edit-data> operations, by issuing a <discard-changes> operation
or by issuing an <update> operation with a different resolution
method.
This resolution method is the default resolution method as it
provides for the highest level of visibility and control to ensure
operational stability.
This resolution method may not be selected by a system operating in
continuous rebase mode when performing automatic <update> operations.
Clients operating in continuous rebase mode may use this resolution
mode in their <update> operation.
Example:
Session 1 edits the configuration by submitting the following
<rpc message-id="config"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<edit-config>
<target><candidate/><target>
<config>
<configure>
<interfaces>
<interface>
<name>intf_one</name>
<description>Link to San Francisco<description>
</interface>
</interfaces>
</configure>
</config>
</edit-config>
</rpc>
Session 2 then edits the configuration deleting the interface
intf_one, updating the description on interface intf_two and
committing the configuration to the running configuration datastore.
Cumming & Wills Expires 30 September 2023 [Page 18]
Internet-Draft NETCONF Private Candidates March 2023
<rpc message-id="config"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<edit-config>
<target><candidate/><target>
<config>
<configure>
<interfaces>
<interface>
<name operation="delete">intf_one</name>
</interface>
<interface>
<name>intf_two</name>
<description>Link moved to Paris</description>
</interface>
</interfaces>
</configure>
</config>
</edit-config>
</rpc>
Session 1 then sends an <update> NETCONF operation.
<rpc message-id="update"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<update>
<resolution-mode>revert-on-conflict</resolution-mode>
</update>
</rpc>
A conflict is detected and no merges/overwrite operations happen.
The resulting data in private candidate 1 is:
<configure>
<interfaces>
<interface>
<name>intf_one</name>
<description>Link to San Francisco<description>
</interface>
<interface>
<name>intf_two</name>
<description>Link to Tokyo<description>
</interface>
</interfaces>
</configure>
4.6. NETCONF operations
Cumming & Wills Expires 30 September 2023 [Page 19]
Internet-Draft NETCONF Private Candidates March 2023
4.6.1. New NETCONF operations
4.6.1.1. <update>
The <update> operation is provided to allow NETCONF clients (or
servers) to trigger a rebase of the private candidate configuration
against the running configuration.
The <update> operation may be triggered manually by the client or
automatically by the server.
The <update> operation MUST be triggered by a <commit> operation
being executed in any candidate configuration on the device if the
device is operating in continuous rebase mode.
The <update> operation SHOULD be triggered by a specific NETCONF
session issuing a <commit> operation.
4.6.1.1.1. <resolution-mode> parameter
The <update> operation takes the <resolution-mode> parameter
The resolution modes are described earlier in this document and the
accepted inputs are:
* revert-on-conflict (default)
* ignore
* overwrite
4.6.2. Updated NETCONF operations
Specific NETCONF operations altered by this document are listed in
this section. Any notable behavior with existing unaltered NETCONF
operations is noted in the appendix.
4.6.2.1. <edit-config>
The <edit-config> operation is updated to accept private-candidate as
valid input to the <target> field.
The use of <edit-config> will create a private candidate
configuration if one does not already exist for that NETCONF session.
Sending an <edit-config> request to private-candidate after one has
been sent to the shared candidate datastore in the same session will
fail (and visa-versa).
Cumming & Wills Expires 30 September 2023 [Page 20]
Internet-Draft NETCONF Private Candidates March 2023
Multiple <edit-config> requests may be sent to the private-candidate
datastore in a single session.
4.6.2.2. <lock> and <unlock>
Performing a <lock> on the private-candidate datastore is a valid
operation and will also lock the running configuration.
Taking a lock on this datastore will stop other session from
committing any configuration changes, regardless of the datastore.
Other NETCONF sessions are still able to create a new private-
candidate configurations.
Performing an <unlock> on the private-candidate datastore is a valid
operation. This will also unlock the running configuration.
Unlocking the private-candidate datastore allows other sessions to
resume <commit> functions.
Changes in the private-candidate datastore are not lost when the lock
is released.
Attempting to perform a <lock> or <unlock> on any other datastore
while the private-candidate datastore is locked will fail.
Attempting to perform a <lock> or <unlock> on any other sessions
private-candidate datastore will also fail.
4.6.2.3. <compare>
Performing a <compare> [RFC9144] with the private-candidate datastore
as either the <source> or <target> is a valid operation.
If <compare> is performed prior to a private candidate configuration
being created, one will be created at that point.
The <compare> operation will be extended to allow the operation to
reference the start of the private candidate's branch (head).
4.6.2.4. <get-config>
The <get-config> operation is updated to accept private-candidate as
valid input to the <source> field.
The use of <get-config> will create a private candidate configuration
if one does not already exist for that NETCONF session.
Cumming & Wills Expires 30 September 2023 [Page 21]
Internet-Draft NETCONF Private Candidates March 2023
Sending an <get-config> request to private-candidate after one has
been sent to the shared candidate datastore in the same session will
fail (and visa-versa).
4.6.2.5. <get-data>
The <get-data> operation accepts the private-candidate as a valid
datastore.
The use of <get-data> will create a private candidate configuration
if one does not already exist for that NETCONF session.
Sending an <get-data> request to private-candidate after one has been
sent to the shared candidate datastore in the same session will fail
(and visa-versa).
4.6.2.6. <copy-config>
The <copy-config> operation is updated to accept private-candidate as
a valid input to the <source> or <target> fields.
4.6.2.7. <delete-config>
The <delete-config> operation is updated to accept private-candidate
as a valid input to the <target> field.
5. IANA Considerations
This memo includes no request to IANA.
6. Security Considerations
This document should not affect the security of the Internet.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
Cumming & Wills Expires 30 September 2023 [Page 22]
Internet-Draft NETCONF Private Candidates March 2023
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/info/rfc8342>.
[RFC9144] Clemm, A., Qu, Y., Tantsura, J., and A. Bierman,
"Comparison of Network Management Datastore Architecture
(NMDA) Datastores", RFC 9144, DOI 10.17487/RFC9144,
December 2021, <https://www.rfc-editor.org/info/rfc9144>.
[RFC5717] Lengyel, B. and M. Bjorklund, "Partial Lock Remote
Procedure Call (RPC) for NETCONF", RFC 5717,
DOI 10.17487/RFC5717, December 2009,
<https://www.rfc-editor.org/info/rfc5717>.
7.2. Informative References
Appendix A. Behavior with unaltered NETCONF operations
A.1. <get>
The <get> operation does not accept a datastore value and therefore
this document is not applicable to this operation. The use of the
get operation will not create a private candidate configuration.
Contributors
The authors would like to thank Jan Lindblad, Jason Sterne and Rob
Wilton for their contributions and reviews.
Authors' Addresses
James Cumming
Nokia
Email: james.cumming@nokia.com
Robert Wills
Cisco Systems
Email: rowills@cisco.com
Cumming & Wills Expires 30 September 2023 [Page 23]