Skip to main content

A Comparison of IPv6-over-IPv4 Tunnel Mechanisms
draft-steffann-tunnels-04

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 7059.
Authors S.J.M. Steffann , Iljitsch van Beijnum , Rick van Rein
Last updated 2013-11-27 (Latest revision 2013-05-31)
RFC stream Independent Submission
Intended RFC status Informational
Formats
IETF conflict review conflict-review-steffann-tunnels
Stream ISE state Published RFC
Consensus boilerplate Unknown
Document shepherd (None)
IESG IESG state Became RFC 7059 (Informational)
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-steffann-tunnels-04
Network Working Group                                        S. Steffann
Internet-Draft                               S.J.M. Steffann Consultancy
Intended status: Informational                            I. van Beijnum
Expires: December 2, 2013                       Institute IMDEA Networks
                                                             R. van Rein
                                                            OpenFortress
                                                            May 31, 2013

            A Comparison of IPv6 over IPv4 Tunnel Mechanisms
                       draft-steffann-tunnels-04

Abstract

   This document provides an overview of various ways to tunnel IPv6
   packets over IPv4 networks.  It covers mechanisms in current use,
   touches on several mechanisms that are now only of historic interest,
   and discusses some newer tunnel mechanisms that are not (yet) widely
   used at the time of publication.  The goal of the document is helping
   people with an IPv6-in-IPv4 tunneling need to select the mechanisms
   that may apply to them.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on December 2, 2013.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents

Steffann, et al.        Expires December 2, 2013                [Page 1]
Internet-Draft                IPv6 tunnels                      May 2013

   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  4
   3.  Tunnel Mechanisms  . . . . . . . . . . . . . . . . . . . . . .  6
     3.1.  Configured Tunnels (Manual Tunnels / 6in4) . . . . . . . .  7
     3.2.  Automatic Tunneling  . . . . . . . . . . . . . . . . . . .  8
     3.3.  IPv6 over IPv4 without Explicit Tunnels (6over4) . . . . .  8
     3.4.  Generic Routing Encapsulation (GRE)  . . . . . . . . . . .  9
     3.5.  Connection of IPv6 Domains via IPv4 Clouds (6to4)  . . . . 10
       3.5.1.  6to4 Provider Managed Tunnels  . . . . . . . . . . . . 11
     3.6.  Anything In Anything (AYIYA) . . . . . . . . . . . . . . . 12
     3.7.  Intra-site Automatic Tunnel Addressing (ISATAP)  . . . . . 13
     3.8.  Tunneling IPv6 over UDP through NATs (Teredo)  . . . . . . 14
     3.9.  IPv6 Rapid Deployment (6rd)  . . . . . . . . . . . . . . . 14
     3.10. Native IPv6 behind NAT44 CPEs (6a44) . . . . . . . . . . . 15
     3.11. Locator/ID Separation Protocol (LISP)  . . . . . . . . . . 16
     3.12. Subnetwork Encapsulation and Adaptation Layer (SEAL) . . . 18
     3.13. Peer-to-Peer IPv6 on Any Internetwork (6bed4)  . . . . . . 18
   4.  Related Protocols  . . . . . . . . . . . . . . . . . . . . . . 19
     4.1.  Tunnel Setup Protocol (TSP)  . . . . . . . . . . . . . . . 20
     4.2.  SixXS Heartbeat Protocol . . . . . . . . . . . . . . . . . 20
     4.3.  Tunnel Information and Control protocol (TIC)  . . . . . . 21
   5.  Common Aspects . . . . . . . . . . . . . . . . . . . . . . . . 21
     5.1.  Protocol 41 Encapsulation  . . . . . . . . . . . . . . . . 21
     5.2.  NAT and Firewalls  . . . . . . . . . . . . . . . . . . . . 22
     5.3.  MTU Considerations . . . . . . . . . . . . . . . . . . . . 24
     5.4.  IPv4 Addresses Embedded in IPv6 Addresses  . . . . . . . . 25
   6.  Evaluation of Tunnel Mechanisms  . . . . . . . . . . . . . . . 27
     6.1.  Efficiency of IPv4 Address Use . . . . . . . . . . . . . . 27
     6.2.  Supported Network Topologies . . . . . . . . . . . . . . . 28
     6.3.  Robustness . . . . . . . . . . . . . . . . . . . . . . . . 29
     6.4.  Gateway State  . . . . . . . . . . . . . . . . . . . . . . 31
     6.5.  Performance  . . . . . . . . . . . . . . . . . . . . . . . 32
   7.  IANA considerations  . . . . . . . . . . . . . . . . . . . . . 33
   8.  Security considerations  . . . . . . . . . . . . . . . . . . . 33
   9.  Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 34
   10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 34
   11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 34
   Appendix A.  Evaluation Criteria . . . . . . . . . . . . . . . . . 38
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 39

Steffann, et al.        Expires December 2, 2013                [Page 2]
Internet-Draft                IPv6 tunnels                      May 2013

1.  Introduction

   During the transition from IPv4 to IPv6, IPv6 islands are separated
   by a sea of IPv4.  Tunnels provide connectivity between these IPv6
   islands.  Tunnels work by encapsulating IPv6 packets inside IPv4
   packets, as shown in the figure.

                                              +---------------+
                                              |     IPv4      |
                                              |    Header     |
                                              +---------------+
            +---------------+                 :   Optional    :
            |     IPv6      |                 : Encapsulation :
            |    Header     |                 :    Header     :
            +---------------+                 +---------------+
            |   Transport   |                 |     IPv6      |
            |    Layer      |      ===>       |    Header     |
            |    Header     |                 +---------------+
            +---------------+                 |   Transport   |
            |               |                 |    Layer      |
            ~     Data      ~                 |    Header     |
            |               |                 +---------------+
            +---------------+                 |               |
                                              ~     Data      ~
                                              |               |
                                              +---------------+

                        Encapsulating IPv6 in IPv4

   Various tunnel mechanisms have been proposed over time.  So many in
   fact, that it is difficult to get an overview.

   Some tunnel mechanisms have been abandoned by the community, others
   have known problems and yet others have shown to be reliable.  Some
   tunnel mechanisms were designed with a particular use-case in mind,
   others are generic.  There may be documented limitations as well as
   limitations that have cropped up in deployment.

   This document provides an overview of available and/or noteworthy
   tunnel mechanisms, with the intention to guide selection of the best
   mechanism for a particular purpose.  As such, the discussion of the
   different tunnel mechanisms is limited to the working principles of
   the different mechanisms and a few important details.

   Please use the references to learn the full details of each
   mechanism.  For brevity, only the most relevant documents are
   referenced.  Refer to these for additional specifications, updates
   and links to older versions of protocol specifications as well as

Steffann, et al.        Expires December 2, 2013                [Page 3]
Internet-Draft                IPv6 tunnels                      May 2013

   links to more general background information.

   The intended audience for this document is everyone who needs a
   connection to the IPv6 internet at large, but is not in the position
   to use native (untunneled) IPv6 connectivity, and thus needs to
   select an appropriate tunnel mechanism.  However, when native IPv6
   connectivity is availalble, this should be preferred over tunneled
   connectivity as per rule 7 in section 6 of [RFC6724].  This document
   is also intended as a quick reference to tunnel mechanisms for the
   IETF community.

   The scope of this document is limited to tunnel mechanisms for
   providing IPv6 connectivity over an IPv4 infrastructure.  Mechanisms
   for Virtual Private Networks (VPNs) and security architectures such
   as IPSec [RFC4301], as well as IPv4 over IPv6 tunneling are out of
   scope for this document as they serve a different purpose, even if
   they could technically be used to provide IPv6 connectivity.

2.  Terminology

   Anycast:  Mechanism to provide a service, in multiple locations
      and/or using multiple servers, by configuring each server with the
      same IP address.

   Carrier Grade NAT (CGN):  A Network Address Translation (see NAT)
      device used by an ISP so multiple subscribers can be served using
      a single IPv4 address.

   Dual stack:  Also known as "dual IP layer".  Nodes run IPv4 and IPv6
      side by side, and can communicate with other dual stack nodes
      (using IPv4 or IPv6), as well as IPv4-only nodes (using IPv4) and
      IPv6-only nodes (using IPv6).  Most current operating systems are
      set up to use IPv4 when available as well as use IPv6 when
      available, allowing them to run in IPv4-only, IPv6-only or dual
      stack mode as circumstances permit.  Except for a few things
      concerning the Domain Name System (DNS), there is no separate
      specification for dual stack beyond the specifications relevant to
      running IPv4 and IPv6.  Dual stack is one of the three IPv4-to-
      IPv6 transition tools; the others are translation and tunnels.

   Encapsulation:  Transporting packets as data inside another packet.
      For instance, an IPv6 packet inside an IPv4 packet.

   Firewall:  A device that selectively filters IP packets, allowing
      some protocols through but not others.  A firewall may act as a
      switch, operating below the IP layer, or as a router.

Steffann, et al.        Expires December 2, 2013                [Page 4]
Internet-Draft                IPv6 tunnels                      May 2013

   Host:  A device that communicates using the Internet Protocol and
      only transmits packets from its own address.

   ISP:  Internet Service Provider; the party connecting the outside of
      the local network's perimeter to the public Internet.

   MTU:  Maximum Transmission unit, the maximum size of a packet that
      can be transmitted over a link (or tunnel) without splitting it
      into multiple fragments.

   NAT:  Network Address Translation or Network Address Translator.  NAT
      makes it possible for a number of hosts to share a single IP
      address.  TCP and UDP port numbers are used to distinguish the
      traffic to/from different hosts served by the NAT; protocols other
      than TCP and UDP may be incompatible with NAT due to lack of port
      numbers.  NAT also breaks protocols that depend on the IP
      addresses used in some way.  Typically, NAT devices behave as a
      host towards the public internet, and as a router towards the
      internal network.

   NBMA:  Non-Broadcast, Multiple Access.  This is a network
      configuration in which nodes can exchange packets directly by
      addressing them at the desired destination.  However, broadcasts
      or multicasts are not supported, so autodiscovery mechanisms such
      as IPv6 Neighbour Discovery must be modified to use unicast to
      work.

   Node:  A device that implements IP, either a host or a router; also
      known as a system.  See note at "NAT".

   Path stretch:  The difference between the shortest path through the
      network and the path (tunneled) packets actually take.

   PMTUD:  Path MTU Discovery, a method to determine the smallest MTU on
      the path between two nodes.  There are separate specifications for
      PMTUD over IPv4 [RFC1191] and IPv6 [RFC1981].

   Router:  A device that forwards IP packets that it didn't generate
      itself.  See note at "NAT".

   System:  A device that implements IP, either a host or a router; a
      network node.

   Translation:  The IPv6 and IPv4 headers are similar enough that it is
      possible to translate between them.  This allows IPv6-only hosts
      to communicate with IPv4-only hosts.  The original specification
      for translating between IPv6 and IPv4, was heavily criticised by
      the Internet Architecture Board, but new specifications for

Steffann, et al.        Expires December 2, 2013                [Page 5]
Internet-Draft                IPv6 tunnels                      May 2013

      translating between IPv6 and IPv4 were later published [RFC6145].
      Translation is of the three IPv4-to-IPv6 transition tools; the
      others are dual stack and tunnels.

   Tunnel:  By encapsulating IPv6 packets inside IPv4 packets, IPv6-
      capable hosts and IPv6-capable networks isolated from other IPv6-
      capable systems or the IPv6 internet at large can exchange IPv6
      packets over IPv4-only infrastructure.  There are numerous ways to
      tunnel IPv6 over IPv4.  This document compares these mechanisms.
      One of the three IPv4-to-IPv6 transition tools; the others are
      translation and dual stack.

   Tunnel broker:  A service that provides tunneled connectivity to the
      IPv6 internet, such as [SIXXS], [TUNBROKER] and [GOGO6].

3.  Tunnel Mechanisms

   Automatic tunnels (Section 3.2), configured tunnels (Section 3.1),
   6over4 (Section 3.3), 6to4 (Section 3.5), ISATAP (Section 3.7) and
   6rd (Section 3.9) solve similar problems at different scales.  They
   all encapsulate IPv6 packets immediately inside an IPv4 packet,
   without using additional headers.  This is called "protocol 41
   encapsulation" (see Section 5.1), as the Protocol field in the IPv4
   header is set to 41 to indicate that what follows is an IPv6 packet.

   Each of these mechanisms also creates an IPv6 address for the host or
   router running the protocol based on the system's IPv4 address in one
   way or another (see Section 5.4).  This lets 6to4, 6rd, ISATAP and
   automatic tunnels determine the IPv4 destination address in the outer
   IPv4 header from the IPv6 address of the destination, allowing for
   automatic operation without the need to administratively configure
   the remote tunnel endpoint.

   6over4 and ISATAP provide IPv6 connectivity between IPv6-capable
   systems within a single organisation's network that is otherwise
   IPv4-only. 6rd allows ISPs to provide IPv6 connectivity to their
   customers over IPv4-only last mile infrastructures. 6to4 directly
   provides connectivity to the global IPv6 internet without involving
   an ISP.

   Configured tunnels (Section 3.1) also use protocol 41 encapsulation,
   but rely on manual configuration of the remote tunnel endpoint.  (The
   Heartbeat Protocol (Section 4.2) solves this.)  Configured tunnels
   can be used within an organisation's network, but are typically used
   by tunnel broker services to provide connectivity to the IPv6
   internet.  GRE (Section 3.4) is similar to configured tunnels, but
   also supports tunnel protocols other than IPv6.

Steffann, et al.        Expires December 2, 2013                [Page 6]
Internet-Draft                IPv6 tunnels                      May 2013

   AYIYA (Section 3.6) is similar to configured tunnels and GRE, but
   typically uses a UDP header for better compatibility with NATs and is
   generally used with TIC (Section 4.3) to set up the tunnel rather
   than rely on manual configuration.  Teredo (Section 3.8), 6a44
   (Section 3.10) and 6bed4 (Section 3.13) are similar to 6to4, except
   that they are designed to work through NATs by running over UDP.  Of
   these, Teredo and 6bed4 assume no ISP involvement and 6a44 does; and
   6bed4 is designed to work over direct IPv4 paths between peers
   whenever possible.

   LISP (Section 3.11) is a system for abstracting the identifying
   function from the location function of IP addresses, which allows for
   the use of IPv6 for the former and IPv4 for the latter.

   SEAL (Section 3.12)) and its companion technologies (VET, AERO, IRON
   and RANGER) provide a configured tunnel system for IPv6-in-IPv4
   tunneling to default routers as well as automatic tunnel endpoint
   discovery for optimisation of more-specific routes.

   Dual-Stack Lite [RFC6333] and MAP [I-D.ietf-softwire-map], both
   developed by the IETF Softwire working group, often come up in
   discussions about IPv6 tunneling.  However, they are _not_ IPv6-in-
   IPv4 tunnel mechanisms.  They are IPv4-in-IPv6 mechanisms for
   providing IPv4 connectivity over an IPv6 infrastructure.

   Please refer to Section 5 for more information about issues common to
   many tunnel mechanisms; those issues are not discussed separately for
   each mechanism.  The mechanisms are discussed below in roughly
   chronological order of first publication.

3.1.  Configured Tunnels (Manual Tunnels / 6in4)

   Configured and automatic tunnels are the two oldest tunnel
   mechanisms, originally published in "Transition Mechanisms for IPv6
   Hosts and Routers" [RFC1933] in 1996.  The latest specification of
   configured tunnels is "Basic Transition Mechanisms for IPv6 Hosts and
   Routers" [RFC4213], published in 2005.  The mechanism is sometimes
   called "manual tunnels", "static tunnels", "protocol 41 tunnels" or
   "6in4".

   Configured tunnels connect two systems in point-to-point fashion
   using protocol 41 encapsulation.  The configuration that the name of
   the mechanism alludes to consists of a remote "tunnel endpoint".
   This is the IPv4 address of the system on the other side of the
   tunnel.  When a system (potentially) has multiple IPv4 addresses, the
   local tunnel endpoint address may also need to be configured.

   The need to explicitly set up a configured tunnel makes them more

Steffann, et al.        Expires December 2, 2013                [Page 7]
Internet-Draft                IPv6 tunnels                      May 2013

   difficult to deploy than automatic mechanisms.  However, because
   there is a fixed, single remote tunnel endpoint, performance is
   predictable and easy to debug.

   In the early days it was not unheard for a small network to get IPv6
   connectivity from another continent.  This excessive path stretch
   makes communication over short geographic distances much less
   efficient because the distance travelled by packets may be larger
   than the geographic distance by an order of magnitude or more.

   Configured tunnels are widely implemented.  Common operating systems
   can terminate configured tunnels, as well as IPv6-capable routers and
   home gateways.  The mechanism is versatile, but is mostly used
   between isolated smaller IPv6-capable networks and the IPv6 internet,
   often through a "tunnel broker" such as tunnelbroker.net [TUNBROKER],
   SixXS [SIXXS] or [GOGO6].

   [RFC4891] discusses the use of IPsec to protect the confidentiality
   and integrity of IPv6 traffic exchanged over configured tunnels.

3.2.  Automatic Tunneling

   Automatic tunneling is described in [RFC2893], "Transition Mechanisms
   for IPv6 Hosts and Routers", but removed in [RFC4213], which is an
   update of RFC 2893.  Configured tunnels (Section 3.1) are closely
   related to automatic tunnels and are specified in RFCs 2893 and 4213,
   too.  Both use protocol 41 encapsulation.

   Hosts that are capable of automatic tunneling use special IPv6
   addresses: IPv4-compatible addresses.  An IPv4-compatible IPv6
   address consists of 96 zero bits followed by the system's IPv4
   address.  When sending packets to destinations within the IPv4-
   compatible ::/96 prefix, the IPv4 destination address in the outer
   IPv4 header is taken from the IPv4 address in the IPv4-compatible
   IPv6 destination address.

   Automatic tunneling has a big limitation: it only allows for
   communication between IPv6-capable systems that both support
   automatic tunneling.  There are no provisions for communicating with
   the native IPv6 internet.  As such, the mechanism is of almost no
   practical use and is not implemented in current operating systems, as
   6to4 (Section 3.5) does what automatic tunneling was supposed to do,
   but also provides connectivity to the rest of the IPv6 internet.

3.3.  IPv6 over IPv4 without Explicit Tunnels (6over4)

   "Transmission of IPv6 over IPv4 Domains without Explicit Tunnels"
   [RFC2529] was published in 1999.  The mechanism is commonly known as

Steffann, et al.        Expires December 2, 2013                [Page 8]
Internet-Draft                IPv6 tunnels                      May 2013

   "6over4".

   6over4 is designed to work within a single organisation's IPv4
   network, where IPv6-capable hosts and routers are separated by IPv4-
   only routers. 6over4 treats the IPv4 network as a "virtual Ethernet"
   for the purpose of IPv6 communication.  It uses IPv4 multicast to
   tunnel IPv6 multicast packets.  A node's IPv4 address is included in
   the Interface Identifier used on the virtual 6over4 interface,
   allowing the exchange of protocol 41 encapsulated packets between
   6over4 nodes without prior administrative configuration.

   Because multicast is supported, standard IPv6 Neighbour Discovery and
   Stateless Address Autoconfiguration [RFC4862] can be used.  Although
   like automatic tunnels (Section 3.2) and other mechanisms, 6over4
   embeds the IPv4 address of the host is in the IPv6 address, the
   destination IPv4 address in the outer IPv4 header is *not* derived
   from the IPv6 address embedded in the inner IPv6 header, but learnt
   through Neighbour Discovery [RFC4861].  In effect, the IPv4 addresses
   of the hosts are used as link-layer addresses, in the same way that
   MAC addresses are used on Ethernet networks.

   One or more routers with connectivity to the global IPv6 internet
   send out Router Advertisements to provide 6over4 hosts with
   connectivity to the rest of the IPv6 internet.

   6over4 has the minimal protocol 41 encapsulation overhead and doesn't
   require manual configuration.  Hosts can only take advantage of
   6over4 if they run the mechanism themselves. 6over4 packets can't
   pass through a NAT successfully, as the IPv4 address exchanged
   through Neighbour Discovery will be different from the one needed to
   reach the host in question, and because without port numbers,
   protocol 41 doesn't allow for multiplexing multiple hosts using this
   encapsulation behind a single IPv4 address.  However, 6over4 works
   within IPv4 domains that reside behind a NAT in their entirety and
   use [RFC1918] addressing.

   Because of its reliance on IPv4 multicast and because local IPv6
   communication is relatively easy to facilitate using IPv6 routers,
   6over4 is not supported in current operating systems.  ISATAP
   (Section 3.7) provides very similar functionality without requiring
   IPv4 multicast capability, and is implemented more widely.

3.4.  Generic Routing Encapsulation (GRE)

   Generic Routing Encapsulation (GRE) [RFC2784] is a generic point-to-
   point tunnel mechanism that allows many other protocols to be
   encapsulated in IP.

Steffann, et al.        Expires December 2, 2013                [Page 9]
Internet-Draft                IPv6 tunnels                      May 2013

   GRE is a simple protocol which is similar to configured tunnels
   (Section 3.1) when used for IPv6-in-IPv4 tunneling.  The main benefit
   of GRE is that it can not only encapsulate IPv6 packets but any
   protocol.  The GRE header causes an extra overhead of 8 to 16 bytes
   depending on which options are used.  GRE sets the Protocol field in
   the IP header to 47.

   The GRE header can optionally contain a checksum, a key to separate
   different traffic flows (for example, different tunnels) between the
   same end points and a sequence number that can be used to prevent
   packets from being processed out of order.

   GRE is implemented in many routers, but not in most consumer-level
   home gateways or desktop operating systems.

3.5.  Connection of IPv6 Domains via IPv4 Clouds (6to4)

   6to4 is specified in "Connection of IPv6 Domains via IPv4 Clouds"
   [RFC3056].  It creates a block of IPv6 addresses from a locally
   configured IPv4 address by concatenating that IPv4 address to the
   prefix 2002::/16, resulting in a /48 IPv6 prefix.  Addresses in
   2002::/16 are considered reachable through the tunnel interface, so
   the 6to4 network functions as a non-broadcast, multiple access (NBMA)
   network through which 6to4 users can communicate.  IPv6 packets are
   encapsulated by adding an IPv4 header with the Protocol field set to
   41.

   The /48 prefix allows a single system running 6to4 to act as a
   gateway or router for a large number of IPv6 hosts.  Alternatively,
   an individual host may run 6to4 and not act as a gateway or router.
   The system running 6to4 must have a globally reachable IPv4 address.
   Using 6to4 with a private IPv4 address [RFC1918] is not possible.

   "An Anycast Prefix for 6to4 Relay Routers" [RFC3068] specifies an
   anycast mechanism for 6to4 relays that provide connectivity between
   the 6to4 network and the regular IPv6 internet.  All public relays
   share the IPv4 address 192.88.99.1, which corresponds to 2002:c058:
   6301::.  Relays advertise reachability towards 2002::/16 towards the
   native IPv6 internet, so packets addressed to systems using 6to4
   addresses are routed to the closest gateway.  The gateway
   encapsulates these packets and forwards them to the IPv4 address
   included in the IPv6 address.  Systems running 6to4 have a default
   route pointing to 2002:c058:6301::, so they tunnel packets addressed
   to non-6to4 IPv6 destinations to the closest relay, which
   decapsulates the packet and forwards them as IPv6 packets.

   The 6to4 protocol adds minimal protocol 41 overhead and requires no
   manual configuration from users.  The biggest problem specific to

Steffann, et al.        Expires December 2, 2013               [Page 10]
Internet-Draft                IPv6 tunnels                      May 2013

   6to4 is that it is unpredictable which 6to4 anycast relay is used.
   These relays are often provided by third parties on a best-effort
   basis.  In practice this has caused unpredictable performance.
   Traffic from the 6to4 network to the regular IPv6 internet will
   likely use a different 6to4 relay than the traffic in the opposite
   direction.  If either of those relays is not reliable then the
   communication between those networks is affected.  Especially the
   lack of control over the relay used for return traffic is considered
   to be a problem with 6to4.

   To avoid problems with 6to4 the IPv6 Default Address Selection
   algorithm [RFC6724] gives IPv4 addresses a higher preference than
   6to4 addresses.  When making a connection a system will prefer native
   IPv6 over IPv4, and IPv4 over 6to4 IPv6.  This causes 6to4 to be used
   only when a destination is not reachable over IPv4 and no other IPv6
   connectivity is available.

   For more information about 6to4, see "Advisory Guidelines for 6to4
   Deployment" [RFC6343].

   *Warning*:

   Although many, if not all, 6to4 implementations disable the mechanism
   when the system only has an RFC 1918 address, recently a block of
   IPv4 address has been set aside for use in service provider operated
   Network Address Translators, also known as Carrier Grade NAT (CGN).
   [RFC6598] sets aside the block 100.64.0.0/10 for the use between CGNs
   and subscriber devices.  As 100.64.0.0/10 is not an RFC 1918 address
   block, systems implementing 6to4 may fail to disable the mechanism,
   but due to the shared nature of the 100.64.0.0/10 prefix, 6to4 cannot
   work using these addresses.  The same issue is present if an ISP
   decides to use regular global unicast IPv4 address space behind a
   CGN.

3.5.1.  6to4 Provider Managed Tunnels

   [RFC6732] describes "6to4 Provider Managed Tunnels", which is a way
   to make 6to4 work behind a CGN.  This is accomplished by running a
   6to4 gateway at the 6to4 gateway anycast address, and then
   translating the IPv6 addresses used by 6to4 users behind the CGN to
   IPv6 addresses from the ISP's range.  Unlike IPv4 NAT, where multiple
   internal hosts share a single public IPv4 address, prefix translation
   translates entire prefixes, so each host has its own public IPv6
   address and can receive incoming packets as usual.

   However, if IPv6 applications are not aware that translation is
   happening (and they have no reason to expect that it is), they may
   not use their externally visible address in referrals, so

Steffann, et al.        Expires December 2, 2013               [Page 11]
Internet-Draft                IPv6 tunnels                      May 2013

   applications that use referrals are likely to fail.  Additionally,
   the translation is only specified for packets that flow through the
   6to4 gateway, not for packets sent directly to other 6to4 users.  So
   communication with other 6to4 users is not possible.  As such, the
   use of 6to4 provider managed tunnels is discouraged except as a very
   last resort.

3.6.  Anything In Anything (AYIYA)

   AYIYA [AYIYA] is designed for use by the SIXXS [SIXXS] tunnel broker
   service.  The specification has been published as an Internet-Draft
   [I-D.massar-v6ops-ayiya].

   The AYIYA protocol defines a method for encapsulating any protocol in
   any other protocol.  The most common way of deploying AYIYA is to use
   the following sequence of headers: IPv4-UDP-AYIYA-IPv6, although
   other combinations like IPv4-AYIYA-IPv6 or IPv6-SCTP-AYIYA-IPv4 are
   also possible.  The draft does not limit the contents nor the
   protocol that carries the AYIYA packets.  In this document we only
   look at the most common usage (IPv4-UDP-AYIYA-IPv6) which is deployed
   on the SixXS tunnel brokers to provide IPv6 access to clients behind
   NAT devices.

   AYIYA specifies the encapsulation, identification, checksum, security
   and certain management operations that can be used once the tunnel is
   established.  It does not specify how the tunnel configuration
   parameters can be negotiated.  Typically, the TIC protocol described
   in Section 4.3 protocol is used for that part of the tunnel setup,
   although the TSP protocol (Section 4.1) could be used.

   AYIYA provides a point-to-point tunnel, over which the endpoints can
   route traffic for any source and destination.  When using SHA-1
   hashing for authentication, as is common when using the AICCU client
   with a SixXS tunnel server, the total packet overhead is 72 bytes (20
   for the IPv4 header, 8 for UDP and 44 for AYIYA).

   AYIYA provides operational commands for querying the hostname,
   address, contact information, software version and last error
   message.  An operational command to ask the other side of the tunnel
   to shut down is also available.  These commands in the protocol can
   make debugging of AYIYA tunnels easier if the tools support them.

   The main advantage of AYIYA is that it can provide a stable tunnel
   through an IPv4 NAT, and possibly multiple layers of NAT.  The UDP
   port numbers allow multiple AYIYA users to share a single IPv4
   address behind a NAT.

   The client will contact the tunnel server at regular intervals and

Steffann, et al.        Expires December 2, 2013               [Page 12]
Internet-Draft                IPv6 tunnels                      May 2013

   the tunnel server will automatically adapt to changing IPv4 addresses
   and/or UDP port numbers.  To prevent a third party from injecting
   rogue packets into the tunnel the client can optionally be
   authenticated by using the identity and signature fields.  A
   timestamp is included in the AYIYA header to guard against replay
   attacks.

   There is currently a single implementation of this protocol: the
   AICCU [AICCU] client software used with the SIXXS [SIXXS] tunnel
   broker service.

3.7.  Intra-site Automatic Tunnel Addressing (ISATAP)

   ISATAP [RFC5214] uses protocol 41 encapsulation, to provide
   connectivity between isolated IPv6-capable nodes within an
   organisation's internal network.  It is similar to 6over4
   (Section 3.3), but without the requirement that the IPv4 network
   supports multicast; unlike 6over4, ISATAP uses a Non-Broadcast
   Multiple Access (NBMA) communication model and thus doesn't support
   multicasts.  The mechanism assigns IPv6 addresses whose interface
   identifier is solely defined by a node's IPv4 address, which is
   assumed to be unique.

   In order to obtain a /64 prefix, an ISATAP host needs to send a
   unicast Router Solicitation to receive a unicast Router Advertisement
   from an ISATAP router.  Without the ability to send and receive IPv6
   multicasts, an ISATAP host must be configured with a Potential Router
   List through an all-IPv4 mechanism, such as manual setup, DHCP or the
   DNS.  Site administrators are encouraged to use a DNS Fully Qualified
   Domain Name using the convention "isatap.domainname" (e.g.,
   isatap.example.com).  Hosts will accept packets with IPv4 sender
   addresses that are either on the Potential Router List, or that are
   embedded in the IPv6 sender address.

   The router's prefix and the IPv4 address together define the IPv6
   address for the ISATAP interface.  This means that precisely one
   ISATAP address is available for each IPv4 address.  As such, each
   host needs to run ISATAP itself in order to enjoy ISATAP IPv6
   connectivity.  The IPv4 address in the destination IPv6 address is
   used to bootstrap Neighbour Discovery.

   [RFC5214] doesn't explicitly address the use of ISATAP using private
   [RFC1918] addresses.  Despite that, the mechanism seems compatible
   with private addresses.  NAT, however, breaks the relationship
   between the IPv4 address embedded in the IPv6 address and would
   therefore make communication between ISATAP hosts impossible.  Any
   device that can communicate with the ISATAP hosts over IPv4 using
   protocol 41 can participate in the IPv6 subnet.

Steffann, et al.        Expires December 2, 2013               [Page 13]
Internet-Draft                IPv6 tunnels                      May 2013

   ISATAP is available in Windows, Linux and Cisco IOS.

3.8.  Tunneling IPv6 over UDP through NATs (Teredo)

   Teredo is specified in [RFC4380] and a few updates; it is designed as
   an automatic tunnel mechanism of last resort.  It can configure an
   IPv6 address behind most NAT devices, but not all.  Because Teredo
   uses encapsulation in UDP, multiple Teredo clients can be
   simultaneously active behind the same NAT.  For each Teredo client, a
   single IPv6 address is then created at the expense of a single
   external UDP port.

   The operation of Teredo is based on a classification of NAT [RFC3489]
   as established during an interaction with a Teredo server.  This
   classification has since been obsoleted [RFC5389] because it assigns
   more properties to NAT than achieved in reality.

   Teredo is present in Windows XP and later, and is enabled by default
   in Windows Vista and later.  However, Windows will only use Teredo
   connectivity as a way to connect to IPv6 destinations of last resort.
   If no other IPv6 connectivity is present, Windows will not even look
   up AAAA records when resolving domain names.  This means that Teredo
   is only used to connect to explicit IPv6 addresses obtained through
   another mechanism than DNS.  An open source implementation named
   Miredo exists for other platforms.

   The performance of Teredo falls noticeably short of that of IPv4.
   The setup time of a connection involves finding a Teredo relay nearby
   the native address to encapsulate and decapsulate traffic, and
   finding this relay can take in the order of seconds.  This process is
   not sufficiently reliable; Teredo fails in about 37% [TERTST] of its
   attempts to connect to native IPv6 destinations.  The round trip time
   of traffic can add tenths of a second, and jitter generally worsens
   if it is dependent on a public relay.

   Teredo clients need to be configured with a Teredo server when
   setting up their local IPv6 address and when initiating a connection
   to a native IPv6 destination.  The hostnames of the Teredo servers
   are usually pre-configured by the vendor of the Teredo
   implementation.  All Microsoft Windows implementation use Teredo
   servers provided by Microsoft by default.

3.9.  IPv6 Rapid Deployment (6rd)

   6rd [RFC5969] is used by service providers to connect customer
   networks behind a CPE to the IPv6 internet.

   The structure of the 6rd protocol is based on 6to4 and it has the

Steffann, et al.        Expires December 2, 2013               [Page 14]
Internet-Draft                IPv6 tunnels                      May 2013

   same minimal overhead as all protocols that use protocol 41
   encapsulation.  The main differences between 6rd and 6to4 are that
   6rd is meant to be used inside a service provider's network and does
   not use a special IPv6 prefix but one or more prefixes routed to the
   service provider.  As such, 6rd users aren't immediately recognisable
   by their IPv6 address the way 6to4 users are.  Where 6to4 uses relays
   based on global anycast routing 6rd uses relays provided and
   maintained by the service provider.  Because of this architecture the
   tunnel does not traverse unknown networks which makes any debugging
   much easier.

   6rd is completely stateless once it is configured.  The tunnel
   endpoints can therefore be deployed using anycast.  This is commonly
   done for the 6rd border relays deployed by the service provider to
   provide redundancy.

   Because of the different prefix, the device used as the 6rd client
   cannot use the hard-coded IPv6 prefix calculation and relay addresses
   of 6to4.  Instead, the 6rd client needs to receive configuration
   information to work.  In principle 6rd nodes may be configured in a
   variety of ways, the most common one being through DHCP.  If the
   client receives its IPv4 address from a DHCPv4 server then the 6rd
   configuration can be included in the DHCP message exchange using the
   6rd DHCPv4 Option defined in [RFC5969].  Manual configuration of 6rd
   options and configuration using [TR-069] is also possible.

   The main advantage of using 6rd is that it allows service providers
   to deploy IPv6 on last mile access networks that for some reason
   cannot provide native IPv6 connectivity.  It does not share the lack
   of predictable routing that 6to4 suffers from, because all routing,
   encapsulation and de-encapsulation is done by the service provider.

   6rd is intended to be a service managed by an ISP or enterprise IT
   department, which must explicitly make 6rd available for clients to
   be able to use it.

3.10.  Native IPv6 behind NAT44 CPEs (6a44)

   Inspired by Teredo, the 6a44 tunnel is described in "Native IPv6
   behind IPv4-to-IPv4 NAT Customer Premise Equipment (6a44)" [RFC6751].
   Its purpose is to enable Internet Service Providers to establish IPv6
   connectivity for their customers, in spite of the use of a CPE or
   home gateway that is not prepared for IPv6.  The infrastructure
   required for this is a 6a44 relay in the ISP's network and a 6a44
   client in the customer's internal network.

   6a44 was explicitly designed to overcome the noted problems with
   Teredo.  Where Teredo was designed as a global solution without

Steffann, et al.        Expires December 2, 2013               [Page 15]
Internet-Draft                IPv6 tunnels                      May 2013

   dependency on ISP co-operation, the 6a44 tunnel explicitly assumes
   ISP co-operation.  Instead of using Teredo's well-known prefix, a /48
   prefix out of the ISP's address space is used.  A well-known
   (anycast) IPv4 address has been assigned for the 6a44 relay to be run
   inside the ISP network without client configuration.  This well-known
   address is allocated from the same IPv4 /24 as 6to4.

   As part of its bootstrapping, a 6a44 client requests an address from
   the 6a44 relay, and a regular keepalive sent by the 6a44 client to
   the 6a44 relay keeps mapping state in NATs and firewalls on the path
   alive.  Traffic passed from the native IPv6 internet to 6a44 is
   encapsulated in UDP and IPv4 by the relay and decapsulated by the
   6a44 client; the opposite is done in the other direction.

3.11.  Locator/ID Separation Protocol (LISP)

   The Locator/ID Separation Protocol (LISP) [RFC6830] is a protocol to
   separate the identity of systems from their location on the internet
   and/or internal network.  The addresses of the systems are called
   Endpoint Identifiers (EIDs) and the addresses of the gateways are
   called Routing Locators (RLOCs).  It is possible to use IPv6 EIDs
   with IPv4 RLOCs and thereby use LISP for tunneling IPv6 over IPv4.

   LISP defines its own packet formats for encapsulation of data packets
   and for control messages.  All such packets are then encapsulated in
   UDP.  Data packets use port 4341 and control packets use port 4342.

   The LISP specification consists of several RFC documents.  The
   relevant ones for IPv6-in-IPv4 tunneling are the base specification
   [RFC6830], Interworking between Locator/ID Separation Protocol (LISP)
   and Non-LISP Sites [RFC6832] and the Locator/ID Separation Protocol
   (LISP) Map-Server Interface [RFC6833].

                    +----+    +----+
                    | MS |    | MR |
                    +----+    +----+       +-----+   /-----------\
                       |        |      /---| xTR |---| LISP site |
          +------+   /------------\---/    +-----+   \-----------/
          | PxTR |---| IP network |
          +------+   \------------/---\    +-----+   /-----------\
                            |          \---| xTR |---| LISP site |
                    /---------------\      +-----+   \-----------/
                    | Non-LISP site |
                    \---------------/

                      An example of a LISP deployment

   LISP introduces new terminology and new concepts.  The relevant ones

Steffann, et al.        Expires December 2, 2013               [Page 16]
Internet-Draft                IPv6 tunnels                      May 2013

   for this document are:

   ITR:  Ingress Tunnel Router, a router encapsulating data packets at
      the border of a LISP site

   ETR:  Egress Tunnel Router, a router decapsulating data packets at
      the border of a LISP site

   xTR:  A router performing both the ITR and the ETR functions

   PITR:  Proxy ITR, a router accepting traffic from non-LISP sites,
      encapsulating it and tunneling it to the LISP sites

   PETR:  Proxy ETR, a router accepting traffic from LISP sites to send
      it to non-LISP sites

   PxTR:  A router performing both the PITR and the PETR functions

   MS:  Map Server, a server accepting RLOC registrations from ETRs

   MR:  Map Resolver, a server that can resolve queries for RLOCs from
      ITRs

   LISP ETRs register the EID prefixes that they can handle traffic for
   in one or more Map Servers.  ITRs and PITRs can then query Map
   Resolvers to determine which RLOCs to use when sending traffic to a
   LISP site.  PITRs advertise aggregates of EID prefixes to the global
   routing table and provide tunneling services for them so that non-
   LISP sites can reach LISP sites.  PETRs provide a way for LISP sites
   to send traffic to non-LISP sites.

   LISP is a complex protocol if only used for tunneling.  What it
   provides additionally is that ETRs can advertise their own RLOC
   addresses, that one site can have multiple xTRs with independent
   RLOCs and that the LISP site administrator can specify priorities and
   weights for those RLOCs.  This provides redundancy and explicit load
   balancing between RLOCs.  It also provides automatic tunneling
   between different sites without using a PxTR if both sites use Map
   Servers and Map Resolvers that are interconnected, for example by
   participating in the LISP Beta Network [LISPBETA].  To facilitate
   these interconnections the LISP Delegated Database Tree (DDT) system
   is available.

   The LISP protocol is implemented on most Cisco devices.  There are
   implementations available for FreeBSD and Linux, as well as a
   platform independent implementation in the Python programming
   language.  Note that for LISP to work, a mapping service not unlike
   the DNS must be in place.

Steffann, et al.        Expires December 2, 2013               [Page 17]
Internet-Draft                IPv6 tunnels                      May 2013

3.12.  Subnetwork Encapsulation and Adaptation Layer (SEAL)

   The Subnetwork Encapsulation and Adaptation Layer (SEAL)
   [I-D.templin-intarea-seal] (along with its companion technologies
   cited therein) provides a hybrid configured/automatic tunneling
   system.  SEAL itself provides a mid-layer of encapsulation between
   the inner IPv6 header and the outer IPv4 header, i.e., as IPv4-SEAL-
   IPv6.  SEAL can also be used in conjunction with an outer UDP
   encapsulation header, e.g., if NAT traversal is necessary.

   The SEAL tunnel endpoint creates bidirectional configured tunnels to
   reach default IPv6 routers, and discovers unidirectional automatic
   tunnels.  SEAL tunnels can be configured over multiple underlying
   IPv4 links whether the addresses are provisioned from public or
   private IPv4 addressing domains.  In that case, multi-homing and
   traffic engineering are naturally supported.

   SEAL provides an optional 32-bit Identifier and variable-length
   Integrity Check Vector that can be used for packet identification,
   message origin authentication, anti-replay and a mid-layer
   segmentation and reassembly capability.  SEAL also provides a SEAL
   Control Message Protocol (SCMP) used for neighbour coordinations
   between tunnel endpoints.  These coordinations are used for functions
   such as tunnel MTU signalling, route optimisations, neighbour
   reachability testing and so on.

   SEAL ensures that packets that are no larger than 1500 bytes can be
   transported through the tunnel by using a tunnel segmentation
   function.  IPv6 packets that are too large to transport through the
   tunnel whole are split into segments.  The segments are encapsulated
   in IPv4 and reassembled into the original IPv6 packets at the remote
   tunnel endpoint.  SEAL also admits packets larger than 1500 bytes
   into the tunnel on a best-effort basis in case the path between the
   tunnel endpoints can support the larger size.

   When SEAL is used alone without its companion technologies, it can be
   used in the same scenarios as for GRE.  However, SEAL provides
   advanced capabilities that make it better suited than GRE for many
   use cases.  There is currently an experimental open source
   implementation of SEAL.

3.13.  Peer-to-Peer IPv6 on Any Internetwork (6bed4)

   The 6bed4 tunnel is specified in "6bed4: Peer-to-Peer IPv6 on Any
   Internetwork" [6BED4].  A specific goal of 6bed4 is to achieve direct
   communication between peers when the intermediate infrastructure does
   not prohibit it.  The advantage of direct communication is to get a
   performance level similar to IPv4.  The address of a 6bed4 peer is

Steffann, et al.        Expires December 2, 2013               [Page 18]
Internet-Draft                IPv6 tunnels                      May 2013

   formed from the external IPv4 address and UDP port.  The tunnel
   service used for fallback connectivity can run anywhere; perhaps at
   the local ISP or perhaps with a third party service provider for
   6bed4, or even on a well-known address.  It is currently an NBMA
   protocol; there are openings for expansion with multicast.

   The setup of 6bed4 is somewhat similar to 6to4, except that it
   employs UDP so it can be used behind NAT.  It also has elements found
   in Teredo, but without a need to classify NATs and induce behaviour
   from that.  The 6bed4 tunnel makes no assumption NAT devices beyond
   straightforward UDP support.  Given this, 6bed4 can create reliable
   IPv6 tunnels.

   In environments where direct connections between 6bed4 peers is
   possible, additional path stretch compared to IPv4 communication is
   avoided, so 6bed4 performance comes close to IPv4 performance.  In
   situations where this is not possible run over the direct path
   between two peers because a NAT that does not conform to [RFC4787] is
   on the path, a fallback to a tunnel server is used.  This increases
   path stretch and affects scalability through its impact on roundtrip
   times and jitter.

   Another area where the tunnel server is needed, is for connectivity
   between 6bed4 peers and native IPv6 hosts.  For reasons of
   performance and scalability, connections between 6bed4 peers are
   preferred over connections between a 6bed4 peer and a native IPv6
   host.  A default address exists to support zero-config operation, but
   it is possible to locally configure a tunnel server as a fallback
   route, which then also defines the tunnel server for the return path.

   6bed4 has been specifically designed to support realtime interactive
   traffic streams, such as SIP calls, between 6bed4-supporting end
   points, assuming that each prefers 6bed4-to-6bed4 traffic over 6bed4-
   to-native traffic.  Under that premise, the only hosts that need to
   go through a tunnel server are those that are behind a NAT with
   Address-Dependent Mapping or Address and Port-Dependent Mapping.  A
   number of different implementations of 6bed4 have been constructed
   [6BED4] during the ongoing development of its specification.

4.  Related Protocols

   The following protocols are not tunnel mechanisms but they can be
   used in the configuration and/or setup phase of such protocols.

Steffann, et al.        Expires December 2, 2013               [Page 19]
Internet-Draft                IPv6 tunnels                      May 2013

4.1.  Tunnel Setup Protocol (TSP)

   The Tunnel Setup Protocol [RFC5572] specifies a protocol for
   negotiating the setup of a variety of tunnel encapsulations.  In this
   document we are only interested in the encapsulation of IPv6 in IPv4.
   The Tunnel Setup Protocol can negotiate these as a protocol 41
   encapsulated tunnel or as a UDP-encapsulated tunnel.  The tunnel
   negotiation is performed as an XML exchange over UDP or TCP.

   As a TSP client exchanges all IPv6 traffic with the same tunnel
   server, there are no concerns caused by NAT implementations.  The
   only concern is to send regular keepalives, for which ICMPv6 ping
   messages to the tunnel server are suggested.  When encapsulating IPv6
   packets directly in IPv4, all protocol 41 limitations apply.  To
   avoid these, an additional UDP header may be used.

   The Tunnel Setup Protocol treats all protocols and ports for one IPv4
   client address as equivalent.  This suffices when protocol 41 is
   used, but for UDP it creates a situation where one user can set up a
   tunnel behind NAT, and another user could hijack the tunnel
   privileges.

   Open source clients for the Tunnel Setup Protocol and a matching
   tunnel infrastructure are provided from the freenet6 tunnel service
   [GOGO6].

4.2.  SixXS Heartbeat Protocol

   The SixXS Heartbeat Protocol [I-D.massar-v6ops-heartbeat] allows
   nodes that have intermittent connectivity or a dynamic IPv4 address
   that changes from time to time to have continuing tunneled IPv6
   connectivity.  One of the goals of the protocol is to determine when
   a node is no longer present at its previous IPv4 address and then
   stop sending tunneled packets to avoid tunneled packets from being
   delivered to the wrong node.  The Heartbeat Protocol then allows a
   tunnel broker to determine a client's new IPv4 address and continue
   sending tunneled packets with minimal interruption.

   To accomplish this, a node sends periodic heartbeat packets to the
   tunnel broker.  If the tunnel broker fails to receive valid heartbeat
   packets, it shuts down the tunnel in question.  Heartbeat packets
   contain an MD5 message authentication code and a timestamp to avoid
   replay attacks.  The Heartbeat Protocol can work with different
   tunnel mechanisms, but it is often used with configured tunnels
   (Section 3.1).

   The protocol is implemented in the SixXS tunnel broker; client
   implementations are available for common operating systems.  AYIYA

Steffann, et al.        Expires December 2, 2013               [Page 20]
Internet-Draft                IPv6 tunnels                      May 2013

   can be considered the successor of the Heartbeat Protocol.

4.3.  Tunnel Information and Control protocol (TIC)

   The Tunnel Information and Control protocol (TIC) protocol [TIC] is
   the setup protocol for the [SIXXS] tunnel broker service.

   With the TIC protocol a tunnel broker user can request a list of
   available tunnels and points-of-presence (POPs) from the tunnel
   broker service.  When the user chooses one of the tunnels, the
   configuration parameters for that tunnel can then be requested
   through TIC.  TIC also provides commands to control the tunnel, for
   example to change the tunnel endpoints, enable or disable the tunnel.

   Authentication of users is done based on username and password.
   Certain tunnel mechanisms, such as AYIYA (Section 3.6) and configured
   tunnels (Section 3.1) with heartbeat (Section 4.2), need a
   synchronised clock between the tunnel server and the client.  TIC
   facilitates this by providing a server timestamp on request.  The
   client can use that to verify that its clock is synchronised with the
   server and show an error message to the user if it is not.

   The TIC protocol is implemented in the AICCU [AICCU] client software
   and in AVM Fritz!Box home routers.

5.  Common Aspects

   The following are aspects common to many or all tunnel mechanisms.

5.1.  Protocol 41 Encapsulation

   The most straightforward way to encapsulate an IPv6 packet inside an
   IPv4 packet is by simply adding an IPv4 header in front of the IPv6
   header.  In this case, the protocol field in the IPv4 header is set
   to the value 41.  This encapsulation is also known as "IPv6 in IPv4"
   and "IP6 Encapsulation".

   This simple "protocol 41" encapsulation is used by a number of tunnel
   mechanisms:

      configured tunnels (Section 3.1)

      automatic tunneling (Section 3.2)

Steffann, et al.        Expires December 2, 2013               [Page 21]
Internet-Draft                IPv6 tunnels                      May 2013

      6over4 (Section 3.3)

      6to4 (Section 3.5)

      ISATAP (Section 3.7)

      6rd (Section 3.9)

5.2.  NAT and Firewalls

   It is not uncommon for NATs and firewalls to block protocol 41
   encapsulated packets, especially at the boundary between an
   organisation's internal network and the public internet.  Other
   tunnel mechanisms than protocol 41 typically employ a UDP header, and
   are somewhat less likely to be filtered, assuming that tunneling is
   initiated on the LAN-side.  UDP is usually subjected to NAPT
   [RFC2663] which additionally translates between internal and external
   port numbers.  (Often, the term "NAT" is used where "NAPT" may be
   more appropriate.)

   Although protocol 41 can in principle work through NAT, there are two
   issues.  First, when the IPv6 address is derived from the IPv4
   address (see Section 5.4), NATing of the outer IPv4 header breaks the
   relationship between the IPv4 and IPv6 addresses.  Second, because
   protocol 41 does not use port numbers, the number of protocol 41
   tunnel endpoints that can be supported behind a NAT device is equal
   to its number of external IPv4 addresses (see Section 6.1).  This
   limitation also applies to GRE.

   Tunnels that pass through a NAT device or stateful firewall need to
   generate traffic at regular intervals to refresh the NAT or firewall
   mapping.  If the mapping is lost, tunneled packets from the outside
   won't be able to pass through the NAT/firewall until a system behind
   the NAT or firewall sends a tunneled packet and the mapping is
   recreated.  Alternatively, a static mapping (often in the form of a
   "default" or "DMZ" host) may be configured manually.

   The following tunnel mechanisms are incompatible with NAT because
   their addresses must be derived from a globally unique IPv4 address:

      automatic tunneling (Section 3.2)

      6to4 (Section 3.5)

      6rd (Section 3.9)

Steffann, et al.        Expires December 2, 2013               [Page 22]
Internet-Draft                IPv6 tunnels                      May 2013

      LISP (Section 3.11)

   Note that it is common to run 6to4 or 6rd on a home gateway device
   that also performs IPv4 NAT.  In this configuration, NAT is not
   applied to tunneled packets, so NAT and 6to4/6rd can coexist.

   The following tunnel mechanisms cannot operate between nodes on
   opposing sides of a NAT, but they do work if _all_ nodes are behind a
   NAT (where RFC 1918 addresses are often used):

      6over4 (Section 3.3)

      ISATAP (Section 3.7)

   The following tunnel mechanisms may work through NAT in some
   circumstances, but are not designed for NAT compatibility:

      configured tunnels (Section 3.1)

      GRE (Section 3.4)

   The following tunnel mechanisms are designed for NAT compatibility:

      AYIYA (Section 3.6)

      Teredo (Section 3.8) (but it is unreliable)

      6a44 (Section 3.10)

      SEAL (Section 3.12)

      6bed4 (Section 3.13)

   The LISP specification requires that locator addresses (the addresses
   in the outer IPv4 header) are globally routable public addresses.

   A tunnel built over UDP makes a claim on a resource, namely an
   external UDP port.  This may impact how well a tunnel will scale in
   an organisation; for instance, if every desktop runs its own tunnel
   client over UDP then the claim on this resource may have some impact.

   Note that ISPs may have multiple subscribers share a public IPv4
   address by performing NAT (Carrier Grade NAT, CGN or CGNAT in this
   context).  In this case, the subscribers' home gateways may receive
   an address in the 100.64.0.0/10 block [RFC6598].  For the purposes of
   tunnel mechanisms, this address block is similar to the [RFC1918]
   address blocks.  However, NAT/RFC1918 aware tunnel implementations
   may not recognise 100.64.0.0/10 as non-public addresses and fail to

Steffann, et al.        Expires December 2, 2013               [Page 23]
Internet-Draft                IPv6 tunnels                      May 2013

   operate successfully.  The same issue is present if an ISP decides to
   use regular global unicast IPv4 address space behind a CGN.

5.3.  MTU Considerations

   Because of the extra IPv4 header and possible additional headers
   between the IPv4 and IPv6 headers, tunnels experience a reduced
   maximum packet size (Maximum Transfer Unit, MTU) compared to native
   IPv6 communication.

   Path MTU discovery (PMTUD) should handle this in nearly all cases,
   but filtering of ICMPv6 "packet too big" messages may lead to an
   inability to communicate because senders of large packets fail to
   perform PMTUD successfully.  However, when a tunnel terminates
   directly on the host using it, the TCP maximum segment size (MSS)
   option communicates the maximum packet size to the remote endpoint,
   so TCP-based communication may still succeed.  If not, the initial
   TCP SYN/ACK exchange happens without issue, but then the session
   stalls as the larger packets containing data are lost.

   With tunnel mechanisms where the MTU is left unspecified, it is
   possible for the two endpoints to have different MTUs: typically, one
   uses the IPv6 minimum, 1280, while the other uses the physical MTU
   minus tunnel overhead, often 1480.  In theory, this should lead to
   PMTUD failures because the "big" side unknowingly sends packets that
   the "small" side can't handle.  However, in practice implementations
   handle incoming packets larger than their own MTU without issue.

   Only when the IPv4 MTU is reduced below 1500 bytes, for instance when
   using PPP over Ethernet (PPPoE, [RFC2516]), issues are more likely to
   arise.  So when the possibility exists that tunneled packets
   encounter a PPPoE link, it is prudent to set the MTU of a tunnel to
   no more than 1472 bytes, so tunneled packets don't have to be
   fragmented.  Additionally, Section 3.2.1 of [RFC4213] recommends
   limiting the MTU of tunnels to the minimum of 1280.

   SEAL was specifically designed to overcome these limitations by
   adding the capability to fragment IPv6 packets prior to encapsulation
   in IPv4 and then reassembling the fragments at the remote tunnel
   endpoint.  This way, the SEAL tunnel ensures that packets that are no
   larger than 1500 bytes will be transported to the tunnel far end even
   if there are restricting links in the path.  SEAL can also admit
   larger packets into the tunnel on a best effort basis in case the
   path between the tunnel endpoints can support this larger size.

Steffann, et al.        Expires December 2, 2013               [Page 24]
Internet-Draft                IPv6 tunnels                      May 2013

5.4.  IPv4 Addresses Embedded in IPv6 Addresses

   Many tunnel mechanisms embed IPv4 addresses or further information in
   the IPv6 addresses they use.  There are two possible reasons for
   this.  First, with an IPv4 address embedded in the IPv6 address, the
   outer IPv4 header can be derived without a need to explicitly
   configure tunnel endpoints.  Automatic tunneling, 6to4, ISATAP, 6bed4
   and Teredo do this. 6over4 embeds the IPv4 address for the second
   reason; it is embedded in the interface identifier, and thus the IPv6
   address, because that way, a (presumably) globally unique interface
   identifier can be generated.

   Automatic tunneling uses IPv4-compatible addresses in the prefix
   ::/96 (i.e., the first 96 bits are all zero).

    |                     96 bits                    |        32       |
    +------------------------------------------------+-----------------+
    |                   0:0:0:0:0:0                  |  IPv4 address   |
    +------------------------------------------------+-----------------+

                  The IPv4-compatible addresses structure

   Systems running 6to4 have addresses in the 6to4 prefix 2002::/16.

    |   16   |        32       |   16   |          64 bits             |
    +--------+-----------------+--------+------------------------------+
    |  2002  |  IPv4 address   | Subnet |        Interface ID          |
    +--------+-----------------+--------+------------------------------+

                        The 6to4 address structure

   Because a 6rd domain might share a common IPv4 prefix it is not
   always necessary to encode all 32 bits of the IPv4 address in the 6rd
   delegated prefix.  The bits that become available because of this
   optimisation can be used to provide more subnet IDs to the user
   and/or to use a smaller address block for the 6rd prefix.

    |     n bits    |    o bits    |   m bits  |    128-n-o-m bits     |
    +---------------+--------------+-----------+-----------------------+
    |  6rd prefix   | IPv4 address | subnet ID |     interface ID      |
    +---------------+--------------+-----------+-----------------------+
    |<--- 6rd delegated prefix --->|

                         The 6rd address structure

   6over4 uses the IPv4 address to generate a 64-bit Interface
   Identifier, which can then be used to create a 128-bit IPv6 address
   through Stateless Address Autoconfiguration.

Steffann, et al.        Expires December 2, 2013               [Page 25]
Internet-Draft                IPv6 tunnels                      May 2013

    |       48 bits       |   16   |        32       |        32       |
    +---------------------+--------+-----------------+-----------------+
    | Organisation prefix | Subnet |       0:0       |  IPv4 address   |
    +---------------------+--------+-----------------+-----------------+

                       The 6over4 address structure

   The ISATAP address structure is similar to the 6over4 address
   structure, except that the unique/local (u) bit signifies whether the
   IPv4 address in the interface identifier is unique.  Presumably, this
   is the case for any non-[RFC1918] IPv4 address.  The group (g) bit is
   set to zero, and the remaining bits are set to to 0x00005EFE.

    |       48 bits       |   16   |        32       |        32       |
    +---------------------+--------+-----------------+-----------------+
    | Organisation prefix | Subnet |    ug00:5EFE    |  IPv4 address   |
    +---------------------+--------+-----------------+-----------------+

                       The ISATAP address structure

   Teredo embeds the Teredo server's IPv4 address, a number of flags, a
   UDP port number as well as the Teredo client's IPv4 address in the
   IPv6 addresses it creates.  For good measure, the UDP port and client
   IPv4 address are "obfuscated" by flipping their bits.

    |     32 bits    |       32      |   16  |   16  |        32       |
    +----------------+---------------+-------+-------+-----------------+
    |     2001:0     |  Server IPv4  | Flags |  Port |   Client IPv4   |
    +----------------+---------------+-------+-------+-----------------+

                       The Teredo address structure

   6a44 can be seen as a combination of 6rd and Teredo.  The 6a44 prefix
   is given out by an ISP.  Both the customer site (home gateway) IPv4
   address as well as the host's/client's RFC 1918 IPv4 address and also
   a port number are embedded in the IPv6 address.

    |         48 bits      |        32       |   16  |        32       |
    +----------------------+-----------------+-------+-----------------+
    |      6a44 prefix     | Cust. site IPv4 |  Port |   Client IPv4   |
    +----------------------+-----------------+-------+-----------------+

                        The 6a44 address structure

   6bed4 embeds two combinations of an IPv4 address and UDP port
   (together acting as a "6bed4 address") in the IPv6 address; the first
   address is for a tunnel server that everyone is certain to reach, the
   other is for the direct address that most peers should be able to

Steffann, et al.        Expires December 2, 2013               [Page 26]
Internet-Draft                IPv6 tunnels                      May 2013

   reach directly.  The tunnel server however, is the only one with
   guaranteed access to the direct address.

    |            64 bits             |          50             |  14   |
    +--------+-----------------------+-------------------------+-------+
    | prefix | general 6bed4 address |  direct 6bed4 address   | lanIP |
    +--------+-----------------------+-------------------------+-------+

                        The 6bed4 address structure

   Some details of the 6bed4 address format are still work in progress
   at the time of this writing.  The lanIP bits are free for local
   purposes, such as creating a DHCPv6 range.

6.  Evaluation of Tunnel Mechanisms

   The following subsections deal with the various aspects of tunnels
   that guide their selection.

6.1.  Efficiency of IPv4 Address Use

   With the depletion of the IPv4 address space, the ability to deploy a
   tunnel mechanism behind NAT as well as the number of IPv6
   subscribers, subnets and individual hosts that can be supported
   behind a single IPv4 address have become important considerations.

   These issues are irrelevant to tunnel mechanisms that provide IPv6
   connectivity between hosts within the same administrative domain,
   such as ISATAP or 6over4, as they can use private IPv4 addresses.
   This is also true for 6rd, which is used between an ISP and its
   customers' home gateways when the ISP has implemented NAT.

   6to4 cannot work behind any kind of NAT.  Most other mechanisms based
   on protocol 41 can work behind NAT, at least in principle.  In
   practice this difference is not as big as the protocol 41
   encapsulation doesn't provide any fields that allow a NAT to
   demultiplex tunneled packets.  This means that only a single protocol
   41 tunnel endpoint can be supported for each public IPv4 address.

   This makes configured tunnels (as well as 6to4) incompatible with
   service provider operated NATs, where multiple subscribers share an
   IPv4 address.

   Teredo, 6a44, 6bed4, AYIYA, SEAL and TSP are designed to work through
   NATs and use a UDP header, so multiple tunnel endpoints can be hosted
   behind a single IPv4 address.  On the other hand, Teredo only
   provides IPv6 connectivity to a single host.

Steffann, et al.        Expires December 2, 2013               [Page 27]
Internet-Draft                IPv6 tunnels                      May 2013

   The following table shows how many IPv4 addresses each tunnel
   mechanism requires and how many IPv6 hosts it can connect.  The
   mechanisms are listed in order of increasing numbers of supported
   IPv6 hosts per IPv4 address.

   +------------+-------------+-------------+-------------+------------+
   | Mechanism  | Tunnels per | IPv6 hosts  | Public IPv4 | NAT        |
   |            | IPv4 addr.  | per tunnel  | address     | compatible |
   +------------+-------------+-------------+-------------+------------+
   | Auto. tun. | one         | one         | required    | no         |
   | 6to4       | one         | multiple    | required    | no         |
   | LISP       | one         | multiple    | required    | no         |
   | 6rd        | one         | multiple    | not needed  | no         |
   | Conf. tun. | one         | multiple    | not needed  | limited    |
   | GRE        | one         | multiple    | not needed  | limited    |
   | Teredo     | multiple    | one         | not needed  | yes (*)    |
   | 6bed4      | multiple    | multiple    | not needed  | yes        |
   | 6a44       | multiple    | multiple    | not needed  | yes        |
   | AYIYA      | multiple    | multiple    | not needed  | yes        |
   | SEAL       | multiple    | multiple    | not needed  | yes        |
   +------------+-------------+-------------+-------------+------------+

                   Tunneled IPv6 hosts per IPv4 address

   (*) Although Teredo is designed for NAT compatibility, it doesn't
   work through all existing NATs.

6.2.  Supported Network Topologies

   There are two ways to use an IPv6-in-IPv4 tunnel to connect to the
   IPv6 internet: using a point-to-point tunnel to a tunnel broker or an
   ISP-operated gateway, or using a non-broadcast multiple access (NBMA)
   tunnel and anycasted public gateways or relays.

   The advantages of the point-to-point model are predictable
   performance and flexibility regarding the IPv6 addresses used.  The
   advantage of the NBMA model is that traffic between two hosts or
   networks that both use the mechanism can flow directly without
   passing through a gateway (direct peer-to-peer communication.).  An
   extra advantage of the NBMA model with public gateways is automatic
   configuration and no involvement from an ISP.

   Unfortunately, the advantages of this NBMA public anycast model come
   at a price: both the peer-to-peer connectivity between tunnel users
   and the connectivity towards the native IPv6 internet may suffer from
   reliability and performance issues.

   The anycast mechanism allows tunnel users to utilise the nearest

Steffann, et al.        Expires December 2, 2013               [Page 28]
Internet-Draft                IPv6 tunnels                      May 2013

   gateway to connect to the IPv6 internet by simply giving each gateway
   the same address.  Routing protocols then select the lowest-cost (and
   presumably, shortest) path towards a gateway.  However, this makes
   the path taken by tunneled packets hard to predict or influence.  It
   is common for traffic in two directions to use different gateways,
   complicating debugging even further.  Because nobody is in charge or
   gets paid for operating a gateway, the number of public gateways is
   lower than would be ideal.  This increases the distance to the
   nearest gateway for some users.  There is also the possibility that
   gateways encounter more traffic than they can handle.

   The advantage of a tunnel provided by an ISP or tunnelbroker is that
   there is a clear responsibility for providing a good service with
   well maintained gateways.

      +------------+---------------+--------------------------------+
      | Mechanism  | Peer-to-peer  | Gateway provided by            |
      +------------+---------------+--------------------------------+
      | Conf. tun. | No            | ISP or Tunnel broker           |
      | AYIYA      | No            | ISP or Tunnel broker           |
      | GRE        | No            | N/A                            |
      | 6a44       | Within domain | ISP                            |
      | 6rd        | Within domain | ISP                            |
      | 6over4     | Globally      | N/A                            |
      | ISATAP     | Within domain | Own organisation               |
      | Teredo     | Globally      | Public                         |
      | 6to4       | Globally      | Public or ISP                  |
      | 6bed4      | Globally      | Public or ISP or Tunnel broker |
      | Auto. tun. | Globally      | N/A                            |
      | LISP       | Configurable  | ISP or Tunnel broker           |
      | SEAL       | Configurable  | ISP or Tunnel broker           |
      +------------+---------------+--------------------------------+

                 Topologies Supported per Tunnel Mechanism

6.3.  Robustness

   Tunnels may fail for three main reasons: when tunneled packets are
   filtered, typically by a firewall, when a tunnel endpoint IPv4
   address changes or when tunneled packets are filtered or because of
   NAT issues.

   If a tunnel endpoint gets a new address, the other side of the tunnel
   needs to know to send packets to the new address.  With mechanisms
   that derive IPv6 addresses from the IPv4 address, the previous IPv6
   addresses become unreachable and new IPv6 addresses must be
   configured.

Steffann, et al.        Expires December 2, 2013               [Page 29]
Internet-Draft                IPv6 tunnels                      May 2013

   Some tunnel mechanisms don't work through NAT, or are limited when
   working through NAT.  NAT mappings can typically only be created by
   traffic from the "inside" to the "outside", not by traffic from
   outside the NAT to the network behind the NAT.

   Point-to-point tunnel mechanisms either work consistently or they
   always fail.  As such, a simple ping to the other side of the tunnel
   is sufficient to learn its state.  Also, point-to-point tunnels may
   support routing protocols, which can automatically reroute traffic
   around a failed tunnel.

   Some tunnel mechanisms use a public gateway to reach the native IPv6
   internet.  Public gateways may or may not be operational and/or
   reachable, and may have limited performance, depending on distance
   and usage.

   Tunnel mechanisms that use a broadcast or non-broadcast multiple
   access (NBMA) communication model may experience failures between
   some combinations of tunnel endpoints and not others.

   The following table lists tunnel mechanisms that provide connectivity
   to the IPv6 internet in order of decreasing robustness.  (However,
   even less-robust mechanisms may function well in suitable
   environments.)

   +------------+---------------+--------------------------------------+
   | Mechanism  | Endpoint      | Main issues                          |
   |            | address       |                                      |
   |            | change        |                                      |
   +------------+---------------+--------------------------------------+
   | LISP       | automatic     | None                                 |
   | 6rd        | interrupt     | None                                 |
   | AYIYA      | automatic     | Transient NAT mapping issues         |
   | Conf. + HB | interrupt     | Proto 41 filtering, competition for  |
   |            |               | NAT mappings (1)                     |
   | Conf. tun. | failure       | Proto 41 filtering, competition for  |
   |            |               | NAT mappings, address change (1)     |
   | GRE        | failure       | Proto 47 filtering, address change   |
   | 6a44       | interrupt     | NAT mapping towards peers            |
   | 6bed4      | interrupt     | NAT mapping towards peers            |
   | 6to4       | interrupt     | Enabled out of the box but filtered, |
   |            |               | gateway performance (2)              |
   | Teredo     | interrupt     | NAT compatibility, mapping towards   |
   |            |               | peers (3)                            |
   +------------+---------------+--------------------------------------+

              Susceptibility of tunnel mechanisms to problems

Steffann, et al.        Expires December 2, 2013               [Page 30]
Internet-Draft                IPv6 tunnels                      May 2013

   Notes:

   (1):  only one protocol 41 tunnel endpoint can receive a NAT mapping
      behind a NAT using a single public IPv4 address.  Additional
      endpoints will not receive incoming packets.  When a tunnel
      endpoint changes its internal address, the old NAT mapping needs
      to time out before a new one can be created.

   (2):  6to4 implementations automatically disable the mechanism when
      the system has an RFC 1918 address.  However, 6to4 may remain
      enabled and be non-operational when ISPs apply NAT using non-RFC
      1918 addresses [RFC6598].

   (3):  whether Teredo can obtain an address depends on the type of NAT
      it detects.  Whether Teredo functions at such an address depends
      on the accuracy of that determination, which is founded on an
      incomplete model of NAT.

   On some widely used implementations, 6to4 has been enabled by default
   without checking whether there was connectivity to the anycasted
   public gateway address.  As a result, 6to4-derived connectivity to
   the IPv6 internet was often found to be broken because of protocol 41
   filtering.  Because of this, many operating systems now try to avoid
   using IPv6 over 6to4.  See [RFC6343].

   Also see [TERTST] for more information about the robustness of
   Teredo.

   There is not a single tunnel mechanism that is more robust in all
   possible ways than every other tunnel mechanism.  However, in general
   mechanisms that use public gateways and peer-to-peer tunneling tend
   to have the most issues.  Configured tunnels on the other hand, often
   work very well, especially if there is no NAT on the path, but may
   need administrative intervention when a tunnel endpoint address
   changes.

6.4.  Gateway State

   There is an additional consideration that is important to operators
   of gateways that connect IPv6-in-IPv4 tunnels to the IPv6 internet:
   how much state a tunnel mechanism requires.

   6to4 and 6rd require no state at all: when encapsulating IPv6 packets
   inside an IPv4 packet, the IPv4 destination address is directly
   copied from bits in the IPv6 destination address.  This makes all
   possible tunneled destinations directly reachable through a single
   virtual interface.

Steffann, et al.        Expires December 2, 2013               [Page 31]
Internet-Draft                IPv6 tunnels                      May 2013

   Teredo, 6a44 and 6bed4 require additional logic to work through NATs,
   which requires them to keep track of relatively volatile state.  They
   also work on a per-host basis rather than allowing a number of hosts
   to make use of a single tunnel.

   With configured tunnels, GRE, AYIYA and SEAL there is no direct
   mapping from (part of) the IPv6 destination address to the IPv4
   destination address.  A typical implementation of these mechanisms is
   by having a virtual tunnel interface for each tunnel.  Packets are
   forwarded to the correct virtual interface through a routing table
   lookup.  Routing tables can grow very large and remain fast, so the
   number of virtual interfaces tends to be the limiting factor for
   tunnel gateways.  AYIYA and the SixXS Heartbeat Protocol also keep
   track of the reachability status of each tunnel.

6.5.  Performance

   There are several reasons why tunneled connectivity may perform
   inferior to native, un-tunneled connectivity.  Inherently, tunnels
   add one or more extra headers, and therefore increase overhead.
   However, for a maximum size (1500 bytes) Ethernet packet the
   additional overhead of an IPv4 header is only 1.3%.

   The process of encapsulation is not inherently slow, but in some
   implementations, it may be.  Larger routers that normally forward
   packets using special purpose hardware, often don't have high
   performance CPUs.  If then tunnel encapsulation must be done by that
   relatively slow CPU, performance will be worse than regular hardware-
   based packet forwarding.

   The path that tunneled packets take can be longer than the path that
   untunneled packets would take.  (Increased path stretch.)  This may
   or may not lead to decreased performance.

Steffann, et al.        Expires December 2, 2013               [Page 32]
Internet-Draft                IPv6 tunnels                      May 2013

   +------------+-----------------+----------------------+-------------+
   | Mechanism  | Overhead        | Increased path       | Variability |
   |            | (bytes)         | stretch              |             |
   +------------+-----------------+----------------------+-------------+
   | Conf. tun. | 20              | may be large         | none        |
   | Auto. tun. | 20              | none                 | none        |
   | 6over4     | 20              | none                 | none        |
   | GRE        | 28 - 36         | may be large         | none        |
   | 6to4       | 20              | may be large         | high        |
   | AYIYA      | 72              | may be large         | low         |
   | ISATAP     | 20              | none                 | none        |
   | Teredo     | 28 - 36         | may be large         | high        |
   | 6rd        | 20              | small                | low         |
   | 6a44       | 20 - 28         | small                | low         |
   | 6bed4      | 28              | may be large         | high        |
   | LISP       | 36              | small                | low         |
   | SEAL       | 24 - variable   | small                | low         |
   +------------+-----------------+----------------------+-------------+

                        Typical tunnel performance

7.  IANA considerations

   None.

8.  Security considerations

   There are many security considerations with tunneling.  An important
   one is that through a tunnel, connectivity to the IPv6 internet may
   exist even though network administrators did not intend for it to be
   there.  "Security Concerns with IP Tunneling" [RFC6169] discusses
   this issue in detail.

   Although in principle, ingress filtering (BCP 38, [RFC2827]) is
   possible with tunnels, in practice, it is relatively easy for spoofed
   packets to make their way through a tunnel.  Not only is it often
   easy to spoof the outer IPv4 header and make false IPv6 packets seem
   to originate from a tunnel broker or gateway, it may also be possible
   for an attacker to route false IPv6 packets through a legitimate
   tunnel broker or gateway.  Many tunneling protocols have various
   means of detecting and rejecting such packets, while others have
   limited or no such provisions.  For instance, see [RFC3964] for how
   this can be addressed with 6to4.

   So it is important to recognise that unless special measures are
   taken (like [RFC4301]), both IPv4 and IPv6 addresses in tunnel

Steffann, et al.        Expires December 2, 2013               [Page 33]
Internet-Draft                IPv6 tunnels                      May 2013

   packets may be spoofed and cannot be relied upon for access controls.
   Such spoofing was used successfully to discover IPv6-in-IPv4 tunnels
   in [TUNDISC].

   Tunnels may also be used by third parties to obfuscate their
   activities or perform amplification attacks.  To avoid contributing
   to this problem, it is important to make sure only locally generated
   packets with legitimate addresses are sent out over tunnels.

9.  Contributors

   Job Snijders contributed text to the points of comparison.  Fred
   Templin provided the text for SEAL and contributed to the security
   considerations.  Jeroen Massar, Brian Carpenter, Tina Tsou, John
   Mann, Suresh Krishnan, Victor Kuarsingh, Dan Jones, Nejc Skoberne and
   Fred Baker reviewed the document and/or offered suggestions for
   improvement.

10.  Acknowledgements

   We wish to thank SURFnet and Rogier Spoor for commissioning this
   work; both their initiative and funding has helped this document to
   be written.

11.  References

   [6BED4]    Van Rein, R., "6bed4: Peer-to-Peer IPv6 on Any
              Internetwork", <http://devel.0cpm.org/6bed4/>.

   [AICCU]    SixXS, "Automatic IPv6 Connectivity Client Utility
              (AICCU)", <http://www.sixxs.net/tools/aiccu/>.

   [AYIYA]    SixXS, "Anything In Anything (AYIYA)",
              <http://www.sixxs.net/tools/ayiya/>.

   [GOGO6]    "Freenet6: Free and Easy IPv6 Connectivity",
              <http://www.gogo6.com/freenet6>.

   [I-D.ietf-softwire-map]
              Troan, O., Dec, W., Li, X., Bao, C., Matsushima, S.,
              Murakami, T., and T. Taylor, "Mapping of Address and Port
              with Encapsulation (MAP)", draft-ietf-softwire-map-07
              (work in progress), May 2013.

   [I-D.massar-v6ops-ayiya]

Steffann, et al.        Expires December 2, 2013               [Page 34]
Internet-Draft                IPv6 tunnels                      May 2013

              Massar, J., "AYIYA: Anything In Anything",
              draft-massar-v6ops-ayiya-02 (work in progress), July 2004.

   [I-D.massar-v6ops-heartbeat]
              Massar, J., "SixXS Heartbeat Protocol",
              draft-massar-v6ops-heartbeat-01 (work in progress),
              June 2005.

   [I-D.templin-intarea-seal]
              Templin, F., "The Subnetwork Encapsulation and Adaptation
              Layer (SEAL)", draft-templin-intarea-seal-55 (work in
              progress), May 2013.

   [LISPBETA]
              "LISP Beta Network", <http://www.lisp4.net/beta-network/>.

   [RFC1191]  Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
              November 1990.

   [RFC1918]  Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and
              E. Lear, "Address Allocation for Private Internets",
              BCP 5, RFC 1918, February 1996.

   [RFC1933]  Gilligan, R. and E. Nordmark, "Transition Mechanisms for
              IPv6 Hosts and Routers", RFC 1933, April 1996.

   [RFC1981]  McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery
              for IP version 6", RFC 1981, August 1996.

   [RFC2516]  Mamakos, L., Lidl, K., Evarts, J., Carrel, D., Simone, D.,
              and R. Wheeler, "A Method for Transmitting PPP Over
              Ethernet (PPPoE)", RFC 2516, February 1999.

   [RFC2529]  Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4
              Domains without Explicit Tunnels", RFC 2529, March 1999.

   [RFC2663]  Srisuresh, P. and M. Holdrege, "IP Network Address
              Translator (NAT) Terminology and Considerations",
              RFC 2663, August 1999.

   [RFC2784]  Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
              Traina, "Generic Routing Encapsulation (GRE)", RFC 2784,
              March 2000.

   [RFC2827]  Ferguson, P. and D. Senie, "Network Ingress Filtering:
              Defeating Denial of Service Attacks which employ IP Source
              Address Spoofing", BCP 38, RFC 2827, May 2000.

Steffann, et al.        Expires December 2, 2013               [Page 35]
Internet-Draft                IPv6 tunnels                      May 2013

   [RFC2893]  Gilligan, R. and E. Nordmark, "Transition Mechanisms for
              IPv6 Hosts and Routers", RFC 2893, August 2000.

   [RFC3056]  Carpenter, B. and K. Moore, "Connection of IPv6 Domains
              via IPv4 Clouds", RFC 3056, February 2001.

   [RFC3068]  Huitema, C., "An Anycast Prefix for 6to4 Relay Routers",
              RFC 3068, June 2001.

   [RFC3489]  Rosenberg, J., Weinberger, J., Huitema, C., and R. Mahy,
              "STUN - Simple Traversal of User Datagram Protocol (UDP)
              Through Network Address Translators (NATs)", RFC 3489,
              March 2003.

   [RFC3964]  Savola, P. and C. Patel, "Security Considerations for
              6to4", RFC 3964, December 2004.

   [RFC4213]  Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms
              for IPv6 Hosts and Routers", RFC 4213, October 2005.

   [RFC4301]  Kent, S. and K. Seo, "Security Architecture for the
              Internet Protocol", RFC 4301, December 2005.

   [RFC4380]  Huitema, C., "Teredo: Tunneling IPv6 over UDP through
              Network Address Translations (NATs)", RFC 4380,
              February 2006.

   [RFC4787]  Audet, F. and C. Jennings, "Network Address Translation
              (NAT) Behavioral Requirements for Unicast UDP", BCP 127,
              RFC 4787, January 2007.

   [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              September 2007.

   [RFC4862]  Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862, September 2007.

   [RFC4891]  Graveman, R., Parthasarathy, M., Savola, P., and H.
              Tschofenig, "Using IPsec to Secure IPv6-in-IPv4 Tunnels",
              RFC 4891, May 2007.

   [RFC5214]  Templin, F., Gleeson, T., and D. Thaler, "Intra-Site
              Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214,
              March 2008.

   [RFC5389]  Rosenberg, J., Mahy, R., Matthews, P., and D. Wing,
              "Session Traversal Utilities for NAT (STUN)", RFC 5389,

Steffann, et al.        Expires December 2, 2013               [Page 36]
Internet-Draft                IPv6 tunnels                      May 2013

              October 2008.

   [RFC5572]  Blanchet, M. and F. Parent, "IPv6 Tunnel Broker with the
              Tunnel Setup Protocol (TSP)", RFC 5572, February 2010.

   [RFC5969]  Townsley, W. and O. Troan, "IPv6 Rapid Deployment on IPv4
              Infrastructures (6rd) -- Protocol Specification",
              RFC 5969, August 2010.

   [RFC6145]  Li, X., Bao, C., and F. Baker, "IP/ICMP Translation
              Algorithm", RFC 6145, April 2011.

   [RFC6169]  Krishnan, S., Thaler, D., and J. Hoagland, "Security
              Concerns with IP Tunneling", RFC 6169, April 2011.

   [RFC6333]  Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual-
              Stack Lite Broadband Deployments Following IPv4
              Exhaustion", RFC 6333, August 2011.

   [RFC6343]  Carpenter, B., "Advisory Guidelines for 6to4 Deployment",
              RFC 6343, August 2011.

   [RFC6598]  Weil, J., Kuarsingh, V., Donley, C., Liljenstolpe, C., and
              M. Azinger, "IANA-Reserved IPv4 Prefix for Shared Address
              Space", BCP 153, RFC 6598, April 2012.

   [RFC6724]  Thaler, D., Draves, R., Matsumoto, A., and T. Chown,
              "Default Address Selection for Internet Protocol Version 6
              (IPv6)", RFC 6724, September 2012.

   [RFC6732]  Kuarsingh, V., Lee, Y., and O. Vautrin, "6to4 Provider
              Managed Tunnels", RFC 6732, September 2012.

   [RFC6751]  Despres, R., Carpenter, B., Wing, D., and S. Jiang,
              "Native IPv6 behind IPv4-to-IPv4 NAT Customer Premises
              Equipment (6a44)", RFC 6751, October 2012.

   [RFC6830]  Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "The
              Locator/ID Separation Protocol (LISP)", RFC 6830,
              January 2013.

   [RFC6832]  Lewis, D., Meyer, D., Farinacci, D., and V. Fuller,
              "Interworking between Locator/ID Separation Protocol
              (LISP) and Non-LISP Sites", RFC 6832, January 2013.

   [RFC6833]  Fuller, V. and D. Farinacci, "Locator/ID Separation
              Protocol (LISP) Map-Server Interface", RFC 6833,
              January 2013.

Steffann, et al.        Expires December 2, 2013               [Page 37]
Internet-Draft                IPv6 tunnels                      May 2013

   [SIXXS]    Massar, J. and P. van Pelt, "IPv6 Deployment & Tunnel
              Broker", <http://www.sixxs.net/>.

   [TERTST]   Huston, G., "Testing Teredo", April 2011,
              <http://www.potaroo.net/ispcol/2011-04/teredo.html>.

   [TIC]      SixXS, "Tunnel Information and Control protocol (TIC)",
              <http://www.sixxs.net/tools/tic/>.

   [TR-069]   The Broadband Forum, "CPE WAN Management Protocol",
              July 2011, <http://www.broadband-forum.org/technical/
              download/TR-069_Amendment-4.pdf>.

   [TUNBROKER]
              Hurricane Electric, "Hurricane Electric Free IPv6 Tunnel
              Broker", <http://www.tunnelbroker.net/>.

   [TUNDISC]  Colitti, L., Di Battista, G., and M. Patrignani, "IPv6-in-
              IPv4 tunnel discovery: methods and experimental results",
              IEEE eTransactions on Network and Service Management
              (eTNSM) vol. 1, no. 1, pag. 2-10, April 2004.

Appendix A.  Evaluation Criteria

   Each type of tunnel has specific advantages and disadvantages.  We
   have considered the following points when evaluating the different
   protocols.  Not every point is mentioned in each section where a
   protocol is described, only those that are specifically relevant to
   that protocol.

   Protocol overhead:  How much overhead does the tunneling protocol
      cause?  There are two factors that play a role: number of
      interactions to set up the tunnel and packet header size causing a
      lower MTU and/or fragmentation.

   Automatic configuration:  Does this protocol require manual
      configuration at the endpoints?

   Predictability:  How predictable is the functioning of the protocol?

   Single host or network:  Is this protocol intended to be used by a
      single host or by a router that then provides IPv6 connectivity to
      multiple hosts?

Steffann, et al.        Expires December 2, 2013               [Page 38]
Internet-Draft                IPv6 tunnels                      May 2013

   Load balancing:  Does the tunnel traffic have enough entropy and/or
      hashability to be able to be load-balanced over multiple links, or
      do all tunnel packets have the same outer 5-tuple?

   Path stretch:  Does the tunnel optimise the route, or is there a big
      potential for a much longer path when using the tunnel?

   NAT traversal:  Can the tunnel pass through a NAT gateway, and does
      it require configuration on that NAT gateway?

   Tunnel endpoint mobility:  Are the IPv4 addresses of the tunnel fixed
      or do they adjust automatically when an endpoint moves.

   State:  Are the endpoints required to keep state for the tunnel or is
      the tunnel stateless?

   Network type:  Is this network a point-to-point or NBMA type of
      network?

   Purpose:  What is the intended purpose of this tunnel protocol?

   Related protocols:  To which protocols is this tunnel protocol
      related?  Are there alternatives?

   Implementations:  Is this protocol supported on the major operating
      systems, routers and firewalls?

   Limitations:  What are the known limitations of this protocol?

Authors' Addresses

   Sander Steffann
   S.J.M. Steffann Consultancy
   Tienwoningenweg 46
   Apeldoorn, Gelderland  7312 DN
   The Netherlands

   Email: sander@steffann.nl

Steffann, et al.        Expires December 2, 2013               [Page 39]
Internet-Draft                IPv6 tunnels                      May 2013

   Iljitsch van Beijnum
   Institute IMDEA Networks
   Avda. del Mar Mediterraneo, 22
   Leganes, Madrid  28918
   Spain

   Email: iljitsch@muada.com

   Rick van Rein
   OpenFortress
   Haarlebrink 5
   Enschede, Overijssel  7544 WP
   The Netherlands

   Email: rick@openfortress.nl

Steffann, et al.        Expires December 2, 2013               [Page 40]