Routing Header Based BIER Information Encapsulation
draft-wang-bier-rh-bier-00
The information below is for an old version of the document.
| Document | Type | Active Internet-Draft (individual) | |
|---|---|---|---|
| Authors | Wei Wang , Aijun Wang | ||
| Last updated | 2021-10-25 | ||
| Stream | (None) | ||
| Formats | plain text htmlized pdfized bibtex | ||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-wang-bier-rh-bier-00
BIER Working Group W. Wang
Internet-Draft A. Wang
Intended status: Standards Track China Telecom
Expires: April 28, 2022 October 25, 2021
Routing Header Based BIER Information Encapsulation
draft-wang-bier-rh-bier-00
Abstract
This draft proposes one new encapsulation schema of Bit Index
Explicit Replication (BIER) information to transfer the multicast
packets within the IPv6 network. By defining a new IPv6 Routing
Header type, it keeps the original source address and destination
address unchanged in forwarding process. The encapsulation schema
can make full use of the existing IPv6 quality assurance methods to
provide high-quality multicast service.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 28, 2022.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
Wang & Wang Expires April 28, 2022 [Page 1]
Internet-Draft RH-BIER October 2021
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Conventions used in this document . . . . . . . . . . . . . . 3
3. BIER Routing Header . . . . . . . . . . . . . . . . . . . . . 3
4. The transmission process of packets with BIER Routing Header 5
4.1. All devices in BIER domain support BIER Routing Header . 5
4.2. Some devices in BIER domain do not support BIER Routing
Header . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Security Considerations . . . . . . . . . . . . . . . . . . . 9
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
7. Normative References . . . . . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9
1. Introduction
Bit Index Explicit Replication (BIER) is a new multicast technology
based on IPv6 defined in [RFC8279]. In BIER domain, the set of
destination nodes of multicast message is mapped into a BitString and
encapsulated into the BIER header. The position of each bit in the
BitString represents an BFER. Compared with the traditional
multicast technology, the nodes in BIER domain do not need to
maintain a multicast tree and save the multicast flow state for each
multicast flow.
At present, there are two methods for encapsulating BIER information
based on IPv6 in IETF: bierin6([I-D.ietf-bier-bierin6]) and
bierv6([I-D.xie-bier-ipv6-encapsulation]).
BIERin6 carries BIER information by defining a new IPv6 next header
type. In the process of transmission, the source address and
destination address in the header will change. BIERv6 carries bier
related information by creating an option type of destination options
header (i.e. bier option). During transmission, the source address
in the header remains unchanged and the destination address will
change.
There are some differences between the above two BIER encapsulation
and forwarding schemes, which is unfavorable to the development of
BIER and its derivatives. In addition, when there is an error in the
transmission process of the message, the source address and
destination address help the operators locate and trace the fault.
The change of source address and destination address during
transmission will increase the difficulty of fault location and
traceability.
Wang & Wang Expires April 28, 2022 [Page 2]
Internet-Draft RH-BIER October 2021
This draft proposes a BIER information transmission scheme without
changing the source and destination addresses. By defining an IPv6
Routing Header type, it carries the relevant information of BIER and
ensures that the source address and destination address do not change
during message transmission. The characteristics of this scheme are
conducive to rapid fault location and traceability, and can make full
use of the existing IPv6 quality assurance technologies to provide
high-quality multicast service.
2. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119] .
3. BIER Routing Header
In RFC8020, the format of IPv6 Routing Header is defined, as shown in
Figure 1.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .
. type-specific data .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: The format of IPv6 Routing Header
Where:
o Next Header(8 bits): indicating the message header type
immediately after the routing header.
o HDR Ext Len(8 bits): indicating the length of the routing header.
o Routing Type(8 bits): TBD. Identifying the newly defined Routing
Header to encode BIER information.
o Segments Left(8 bits): indicating the number of explicitly listed
intermediate nodes to be accessed before reaching the final
destination. It is not used here for the time being, and all are
set to 0.
Wang & Wang Expires April 28, 2022 [Page 3]
Internet-Draft RH-BIER October 2021
o Type-specific data(variable): Its format is determined by the
routing type. The length should ensure that the complete routing
header is an integer multiple of 8 octets.
We define a new Routing Header type: BIER Routing Header to carry
BIER related information. The message format of the newly defined
Routing Header type is shown in Figure 2.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segment Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BIFT-id | Ver | TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BSL | Entropy | DSCP |OAM|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BFIR-id |Rsv| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .
. BitString .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: The format of BIER Routing Header
Where:
o BIFT-id(20 bits): each < SD, Si, BSL > is assigned a BIFT-id.
o Ver(4 bits): identifying the version of the BIER header. When an
unsupported BIER header version is received, the BFR needs to
discard the packet and record the error.
o TTL(8 bits): indicating the lifetime of the message. It is used
to prevent ring. The processing process is the same as that in
non MPLS networks.
o BSL(4 bits): indicating the length of BitString.
o Entropy(20 bits): this field specifies an "entropy" for ECMP.
o DSCP(6 bits): this field is used to support different service
codes.
o OAM(2 bits): by default, this value will be set to 0 by BFIR, and
other BFRs will not be modified. Whether to use this field is
optional.
Wang & Wang Expires April 28, 2022 [Page 4]
Internet-Draft RH-BIER October 2021
o BFIR-id(16 bits): indicating BFR ID of BFIR.
o Rsv(2 bits): unused, set to 0.
o Reserved (14 bits): reserved field, set to 0.
o BitString(variable): the length must be reflected in the BSL
field. The string saved in this field is used to identify the
destination BFER of the packet.
4. The transmission process of packets with BIER Routing Header
Based on the newly defined BIER Routing Header, the devices support
BIER Routing Header resolution will perform the following steps:
1) Checking whether there is BIFT corresponding to the BIFT-id
locally.
2) Checking whether the direct-connected device support BIER Routing
Header. If yes, proceed to step 3; otherwise, proceed to step 2.1.
2.1) Calculating the IPv6 address of next hop that support BIER
Routing Header.
2.2) Encapsulating an outer IPv6 Header to the packet. The
calculated IPv6 address is used as the destination address of the
outer IPv6 Header, and its own IPv6 address is used as the source
address of the outer IPv6 Header. BitString will not be changed.
2.3) Sending the encapsulated packet to the next-connected device,
the device will perform normal IPv6 forwarding according to the outer
IPv6 Header.
3) Performing the normal BIER forwarding process as described in
[RFC8279].
The detail procedures for forwarding the multicast packets based on
the newly defined Routing Header are described in the following
sections.
4.1. All devices in BIER domain support BIER Routing Header
+---+
+-----------+ B +----------+
| +---+ |
| 0:01000000 |
| |
| |
Wang & Wang Expires April 28, 2022 [Page 5]
Internet-Draft RH-BIER October 2021
| |
+-+-+ +-+-+ (Packet 2) +---+ (Packet 3)+---+
| A |0:10000000 0:00100000| C +------------+ E +-----------+ F |
+-+-+ +-+-+ +---+ +---+
| | 0:00001000 0:00000100
| |
| |
| |
| 0:00010000 |
| +---+ |
+-----------+ D +----------+
(Packet 1) +---+
Packet 1
+----------------------------+
IPv6 | Source IP Address = A |
Header +----------------------------+
| Destination IP Address = F |
BIER +----------------------------+
Routing| BitString = 00101100 |
Header +----------------------------+
Packet 2
+----------------------------+
IPv6 | Source IP Address = A |
Header +----------------------------+
| Destination IP Address = F |
BIER +----------------------------+
Routing| BitString = 00001100 |
Header +----------------------------+
Packet 3
+----------------------------+
Inner | Source IP Address = A |
IPv6 +----------------------------+
Header | Destination IP Address = F |
+----------------------------+
BIER | BitString = 00000100 |
Routing+----------------------------+
Header
Figure 3: All devices in BIER domain support BIER Routing Header
The topology is shown in Figure 3, device A-F support BIER Routing
Header resolution. The packet need to be transmitted from A to F.
Wang & Wang Expires April 28, 2022 [Page 6]
Internet-Draft RH-BIER October 2021
The change of the Header has been given in the Figure. Each device
will perform the following steps after receiving the packet:
1. Checking whether there is BIFT corresponding to the BIFT-id
locally. If yes, proceed to step 2; otherwise, discard the packet.
2. Checking whether the direct-connected device support BIER Routing
Header. If yes, forwarding the packet according to the BIFT related
to the BIFT-id; otherwise, see sectionSection 4.2 for detail
procedures.
In this forwarding process, the source address and destination
address in the Inner IPv6 Header are not changed, only the BitString
in BIER Routing Header is changed.
4.2. Some devices in BIER domain do not support BIER Routing Header
+---+
+-----------+ B +-----------+
| +---+ |
| 0:01000000 |
| |
| |
| |
+-+-+ +-+-+ (Packet 2) +---+ (Packet 3) +---+
| A |0:10000000 | C +------------+ E +------------+ F |
+-+-+ +-+-+ +---+ +---+
| | 0:00001000 0:00000100
| |
| |
| |
| 0:00010000 |
| +---+ |
+-----------+ D +-----------+
(Packet 1) +---+
Packet 1
+----------------------------+
Outer | Source IP Address = A |
IPv6 +----------------------------+
Header | Destination IP Address = E |
+----------------------------+
Inner | Source IP Address = A |
IPv6 +----------------------------+
Header | Destination IP Address = F |
+----------------------------+
BIER | BitString = 00001100 |
Wang & Wang Expires April 28, 2022 [Page 7]
Internet-Draft RH-BIER October 2021
Routing+----------------------------+
Header
Packet 2
+----------------------------+
Outer | Source IP Address = C |
IPv6 +----------------------------+
Header | Destination IP Address = E |
+----------------------------+
Inner | Source IP Address = A |
IPv6 +----------------------------+
Header | Destination IP Address = F |
+----------------------------+
BIER | BitString = 00001100 |
Routing+----------------------------+
Header
Packet 3
+----------------------------+
IPv6 | Source IP Address = A |
Header +----------------------------+
| Destination IP Address = F |
BIER +----------------------------+
Routing| BitString = 00000100 |
Header +----------------------------+
Figure 4: Some devices in BIER domain do not support BIER Routing Header
The topology is shown in Figure 4, all devices expect device C
support BIER Routing Header resolution. The packet need to be
transmitted from A to F. The change of the Header has been given in
the Figure 4. When it is found that device C does not support BIER
Routing Header resolution, device A will perform the following steps
after receiving the packet:
1. Calculating the IPv6 address of next hop device that supports
BIER Routing Header.
2. Encapsulating an outer IPv6 Header to the packet. The calculated
IPv6 address is used as the destination address of the outer IPv6
Header, and its own IPv6 address is used as the source address of the
outer IPv6 Header. BitString will not be changed.
3. Sending the packet to device C.
After receiving the packet, device C will perform IPv6 forwarding
according the information in outer IPv6 Header, and send the packet
to device E. Device E will send it to device F according the
information in BIER Routing Header. In the forwarding process, the
Wang & Wang Expires April 28, 2022 [Page 8]
Internet-Draft RH-BIER October 2021
source address and destination address in the Inner IPv6 Header are
not changed.
5. Security Considerations
TBD
6. IANA Considerations
This document defines a new IPv6 Routing Header - BIER Routing
Header. The code point is from the "Internet Protocol Version 6
(IPv6) Parameters - Routing Types". It is recommended to set the
code point of BIER Routing Header to 7.
7. Normative References
[I-D.ietf-bier-bierin6]
Zhang, Z., Zhang, Z., Wijnands, I., Mishra, M., Bidgoli,
H., and G. Mishra, "Supporting BIER in IPv6 Networks
(BIERin6)", draft-ietf-bier-bierin6-00 (work in progress),
June 2021.
[I-D.xie-bier-ipv6-encapsulation]
Xie, J., Geng, L., McBride, M., Asati, R., Dhanaraj, S.,
Zhu, Y., Qin, Z., Shin, M., Mishra, G., and X. Geng,
"Encapsulation for BIER in Non-MPLS IPv6 Networks", draft-
xie-bier-ipv6-encapsulation-10 (work in progress),
February 2021.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8279] Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
Przygienda, T., and S. Aldrin, "Multicast Using Bit Index
Explicit Replication (BIER)", RFC 8279,
DOI 10.17487/RFC8279, November 2017,
<https://www.rfc-editor.org/info/rfc8279>.
Authors' Addresses
Wang & Wang Expires April 28, 2022 [Page 9]
Internet-Draft RH-BIER October 2021
Wei Wang
China Telecom
Beiqijia Town, Changping District
Beijing, Beijing 102209
China
Email: weiwang94@foxmail.com
Aijun Wang
China Telecom
Beiqijia Town, Changping District
Beijing, Beijing 102209
China
Email: wangaj3@chinatelecom.cn
Wang & Wang Expires April 28, 2022 [Page 10]