YANG Datastore Telemetry (YANG Push Lite)
draft-wilton-netconf-yang-push-lite-00
This document is an Internet-Draft (I-D).
Anyone may submit an I-D to the IETF.
This I-D is not endorsed by the IETF and has no formal standing in the
IETF standards process.
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Replaced".
|
|
|---|---|---|---|
| Authors | Robert Wilton , Holger Keller , Benoît Claise , Ebben Aries , James Cumming , Thomas Graf | ||
| Last updated | 2025-03-03 | ||
| Replaces | draft-wilton-netconf-yp-observability | ||
| Replaced by | draft-wilton-netconf-yang-push-2 | ||
| RFC stream | (None) | ||
| Formats | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-wilton-netconf-yang-push-lite-00
Network Configuration R. Wilton, Ed.
Internet-Draft Cisco Systems
Intended status: Standards Track H. Keller
Expires: 4 September 2025 Deuetsche Telekom
B. Claise
Huawei
E. Aries
Juniper
J. Cumming
Nokia
T. Graf
Swisscom
3 March 2025
YANG Datastore Telemetry (YANG Push Lite)
draft-wilton-netconf-yang-push-lite-00
Abstract
YANG Push Lite is a YANG datastore telemetry solution, as an
alternative specification to the Subscribed Notifications and YANG
Push solution, specifically optimized for the efficient observability
of operational data.
About This Document
This note is to be removed before publishing as an RFC.
The latest revision of this draft can be found at
https://rgwilton.github.io/draft-yp-observability/draft-wilton-
netconf-yp-observability.html. Status information for this document
may be found at https://datatracker.ietf.org/doc/draft-wilton-
netconf-yang-push-lite/.
Discussion of this document takes place on the Network Configuration
Working Group mailing list (mailto:netconf@ietf.org), which is
archived at https://mailarchive.ietf.org/arch/browse/netconf/.
Subscribe at https://www.ietf.org/mailman/listinfo/netconf/.
Source for this draft and an issue tracker can be found at
https://github.com/rgwilton/draft-yp-observability.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Wilton, et al. Expires 4 September 2025 [Page 1]
Internet-Draft YANG-Push Lite March 2025
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 4 September 2025.
Copyright Notice
Copyright (c) 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Document Status . . . . . . . . . . . . . . . . . . . . . . . 5
2. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1. Background and Motivation for YANG Push Lite . . . . . . 6
3.2. Complexities in Modelling the Operational State
Datastore . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3. Complexities for Consumers of YANG Push Data . . . . . . 8
3.3.1. Combined periodic and on-change subscription . . . . 9
3.4. Relationships to existing RFCs and Internet Drafts . . . 10
3.4.1. RFC 8639 and RFC 8641 . . . . . . . . . . . . . . . . 10
3.4.2. I-D.draft-netana-netconf-notif-envelope and RFC
5277 . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4.3. RFC 9196 and
I-D.draft-netana-netconf-yp-transport-capabilities . 11
3.4.4. I-D.draft-ietf-netconf-https-notif and
I-D.draft-ietf-netconf-udp-notif . . . . . . . . . . 11
3.4.5.
4. YANG Push Lite Overview . . . . . . . . . . . . . . . . . . . 11
5. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Subscription paths and selection filters . . . . . . . . . . 16
Wilton, et al. Expires 4 September 2025 [Page 2]
Internet-Draft YANG-Push Lite March 2025
6.1. _YPath_ definition . . . . . . . . . . . . . . . . . . . 17
6.2. The "filters" Container . . . . . . . . . . . . . . . . . 18
6.3. Decomposing Subscription Filters . . . . . . . . . . . . 19
7. Datastore Event Streams . . . . . . . . . . . . . . . . . . . 20
7.1. Notification Envelope . . . . . . . . . . . . . . . . . . 21
7.2. Event Records . . . . . . . . . . . . . . . . . . . . . . 23
7.3. Types of subscription event monitoring . . . . . . . . . 24
7.4. Periodic events . . . . . . . . . . . . . . . . . . . . . 25
7.5. On-Change events . . . . . . . . . . . . . . . . . . . . 25
7.5.1. On-Change Notifiable Datastore Nodes . . . . . . . . 26
7.5.2. On-Change Considerations . . . . . . . . . . . . . . 27
7.6. Combined periodic and on-change subscriptions . . . . . . 28
7.7. Streaming Update Examples . . . . . . . . . . . . . . . . 28
8. Receivers, Transports, and Encodings . . . . . . . . . . . . 29
8.1. Receivers . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1.1. Receivers for Configured Subscriptions . . . . . . . 30
8.1.2. Receivers for Dynamic Subscriptions . . . . . . . . . 32
8.2. Transports . . . . . . . . . . . . . . . . . . . . . . . 32
8.2.1. Requirements for Yang Push Lite Transport
Specifications . . . . . . . . . . . . . . . . . . . 32
8.2.2. DSCP Marking . . . . . . . . . . . . . . . . . . . . 33
8.3. Encodings . . . . . . . . . . . . . . . . . . . . . . . . 33
9. Setting up and Managing Subscriptions . . . . . . . . . . . . 34
9.1. Configured Subscriptions . . . . . . . . . . . . . . . . 36
9.1.1. Configured Subscription State Machine . . . . . . . . 38
9.1.2. Creating a Configured Subscription . . . . . . . . . 41
9.1.3. Modifying a Configured Subscription . . . . . . . . . 42
9.1.4. Deleting a Configured Subscription . . . . . . . . . 42
9.1.5. Resetting a Configured Subscription . . . . . . . . . 43
9.2. Dynamic Subscriptions . . . . . . . . . . . . . . . . . . 43
9.2.1. Dynamic Subscription State Machine . . . . . . . . . 44
9.2.2. Establishing a Dynamic Subscription . . . . . . . . . 45
9.2.3. Deleting a Dynamic Subscription . . . . . . . . . . . 46
9.2.4. Killing a Dynamic Subscription . . . . . . . . . . . 47
9.2.5. RPC Failures . . . . . . . . . . . . . . . . . . . . 47
9.3. Implementation Considerations (from RFC 8639) . . . . . . 48
9.4. Event Record Delivery . . . . . . . . . . . . . . . . . . 49
10. Subscription Lifecycle Notifications . . . . . . . . . . . . 50
10.1. "subscription-started" . . . . . . . . . . . . . . . . . 50
10.2. "subscription-terminated" . . . . . . . . . . . . . . . 51
10.3. "replay-completed" . . . . . . . . . . . . . . . . . . . 52
11. Performance, Reliability, and Subscription Monitoring . . . . 53
11.1. Subscription Monitoring . . . . . . . . . . . . . . . . 54
11.2. Robustness and Reliability . . . . . . . . . . . . . . . 54
11.3. Publisher Capacity . . . . . . . . . . . . . . . . . . . 55
12. Conformance and Capabilities . . . . . . . . . . . . . . . . 56
12.1. Capabilities . . . . . . . . . . . . . . . . . . . . . . 56
12.2. Subscription Content Schema Identification . . . . . . . 58
Wilton, et al. Expires 4 September 2025 [Page 3]
Internet-Draft YANG-Push Lite March 2025
13. YANG . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
13.1. ietf-yp-lite YANG tree . . . . . . . . . . . . . . . . . 58
13.2. ietf-yp-lite YANG Model . . . . . . . . . . . . . . . . 61
13.3. ietf-yp-lite-capabilities YANG tree . . . . . . . . . . 87
13.4. ietf-yp-lite-capabiltiies YANG Model . . . . . . . . . . 88
14. Security Considerations . . . . . . . . . . . . . . . . . . . 93
14.1. Receiver Authorization . . . . . . . . . . . . . . . . . 94
14.2. YANG Module Security Considerations . . . . . . . . . . 95
15. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 96
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 97
Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 97
References . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Normative References . . . . . . . . . . . . . . . . . . . . . 97
Informative References . . . . . . . . . . . . . . . . . . . . 99
Appendix A. Functional changes between YANG Push Lite and YANG
Push . . . . . . . . . . . . . . . . . . . . . . . . . . 103
A.1. Removed Functionality . . . . . . . . . . . . . . . . . . 103
A.2. Changed Functionality . . . . . . . . . . . . . . . . . . 104
A.3. Added Functionality . . . . . . . . . . . . . . . . . . . 105
Appendix B. Subscription Errors (from RFC 8641) . . . . . . . . 106
B.1. RPC Failures . . . . . . . . . . . . . . . . . . . . . . 106
B.2. Failure Notifications . . . . . . . . . . . . . . . . . . 107
Appendix C. Examples . . . . . . . . . . . . . . . . . . . . . . 107
C.1. Example of update message using the new style update
message . . . . . . . . . . . . . . . . . . . . . . . . . 108
C.2. Example of an on-change-update notification using the new
style update message . . . . . . . . . . . . . . . . . . 110
C.3. Example of an on-change-delete notification using the new
style update message . . . . . . . . . . . . . . . . . . 112
C.4. Subscription RPC examples (from RFC 8641) . . . . . . . . 113
C.4.1. "establish-subscription" RPC . . . . . . . . . . . . 113
C.4.2. "delete-subscription" RPC . . . . . . . . . . . . . . 116
C.4.3. "resync-subscription" RPC . . . . . . . . . . . . . . 116
Appendix D. Summary of Open Issues & Potential Enhancements . . 116
D.1. Issues related to general IETF process: . . . . . . . . . 116
D.2. Issue related to Terminology/Definitions: . . . . . . . . 117
D.3. Issues related to YANG Push Lite Overview. . . . . . . . 117
D.4. Issues related to Subscription Paths and Selection
Filters . . . . . . . . . . . . . . . . . . . . . . . . 117
D.5. Issues related to Datastore Event Streams . . . . . . . . 118
D.5.1. Further refinements on how a subscription can be
decomposed internally into child subscriptions with the
data returned for each child subscription: . . . . . 118
D.5.2. Questions/comments on the notification message
format: . . . . . . . . . . . . . . . . . . . . . . . 119
D.6. Issues related to Receivers, Transports, & Encodings . . 119
D.6.1. Constraints on supporting multiple receivers: . . . . 119
D.6.2. Issues related to Transports: . . . . . . . . . . . . 121
Wilton, et al. Expires 4 September 2025 [Page 4]
Internet-Draft YANG-Push Lite March 2025
D.7. Issues related to Setting up & Managing Subscriptions . . 121
D.7.1. Issues related to the configuration model: . . . . . 121
D.7.2. Issues related to dynamic subscriptions: . . . . . . 122
D.8. Issues related to Subscription Lifecycle . . . . . . . . 123
D.9. Issues related to Performance, Reliability & Subscription
Monitoring . . . . . . . . . . . . . . . . . . . . . . . 126
D.9.1. Issues/questions related to operational data: . . . . 126
D.10. Issues related to Conformance and Capabilities . . . . . 127
D.11. Issues related to the YANG Modules . . . . . . . . . . . 127
D.12. Issues related to the Security Considerations (& NACM
filtering) . . . . . . . . . . . . . . . . . . . . . . . 128
D.13. Issues related to the IANA . . . . . . . . . . . . . . . 128
D.14. Issues related to the Appendixes . . . . . . . . . . . . 128
D.14.1. Examples related issues/questions: . . . . . . . . . 128
D.15. Summary of closed/resolved issues . . . . . . . . . . . . 128
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 129
1. Document Status
_RFC Editor: If present, please remove this section before
publication._
Based on the feedback received during the IETF 121 NETCONF session,
this document has currently been written as a self-contained
lightweight protocol and document replacement for [RFC8639] and
[RFC8641], defining a separate configuration data model.
*The comparison between YANG Push and YANG Push Lite is now in
Appendix A.*
*Open issues are either now being tracked inline in the text or in
Appendix D for the higher level issues.*
2. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
All _YANG tree diagrams_ used in this document follow the notation
defined in [RFC8340].
Wilton, et al. Expires 4 September 2025 [Page 5]
Internet-Draft YANG-Push Lite March 2025
3. Introduction
[I-D.ietf-nmop-yang-message-broker-integration] describes an
architecture for how YANG datastore telemetry, e.g., [RFC8641], can
be integrated effectively with message brokers, e.g., [Kafka], that
forms part of a wider architecture for a _Network Anomaly Detection
Framework_, specified in
[I-D.ietf-nmop-network-anomaly-architecture].
This document specifies "YANG Push Lite", an lightweight alternative
to Subscribed Notifications [RFC8639] and YANG Push [RFC8641]. YANG
Push Lite is a separate YANG datastore telemetry solution, which can
be implemented independently or, if desired, alongside [RFC8639] and
[RFC8641].
At a high level, YANG Push Lite is designed to solve a similar set of
requirements as YANG Push, and it reuses a significant subset of the
ideas and base solution from YANG Push. YANG Push Lite defines a
separate data model to allow concurrent implementation of both
protocols and to facilitate more significant changes in behavior, but
many of the data nodes are taken from YANG Push and have the same, or
very similar definitions.
The following sections give the background for the solution, and
highlight the key ways that this specification differs from the
specifications that it is derived from.
3.1. Background and Motivation for YANG Push Lite
A push based telemetry solution, as described both in this document
and also the YANG Push solution described by [RFC8639] and [RFC8641],
is beneficial because it allows operational data to be exported by
publishers more immediately and efficiently compared to legacy poll
based mechanisms, such as SNMP [RFC3411]. Some further background
information on the general motivations for push based telemetry,
which equally apply here, can be found in the _Motivation_ (section
1.1) of [RFC8639] and the Introduction (section 1) of [RFC8641]. The
remainder of this section is focused on the reasons why a new
lightweight version of YANG Push has been specified, and what
problems is aims to solve.
Early implementation efforts of the
[I-D.ietf-nmop-yang-message-broker-integration] architecture hit
issues with using either of the two common YANG datastore telemetry
solutions that have been specified, i.e., [gNMI] or YANG Push
[RFC8641].
Wilton, et al. Expires 4 September 2025 [Page 6]
Internet-Draft YANG-Push Lite March 2025
gNMI is specified by the OpenConfig Industry Consortium. It is more
widely implemented, but operators report that some inter-operability
issues between device implementations cause problems. Many of the
OpenConfig protocols and data models are also expected to evolve more
rapidly than IETF protocols and models - that are expected to have a
more gradual pace of evolution once an RFC has been published.
YANG Push [RFC8641] was standardized by the IETF in 2019, but market
adoption has been rather slow. During 2023/2024, when vendors
started implementing, or considering implementing, YANG Push, it was
seen that some design choices for how particular features have been
specified in the solution make it expensive and difficult to write
performant implementations, particularly when considering the
complexities and distributed nature of operational data. In
addition, some design choices of how the data is encoded (e.g., YANG
Patch [RFC8072]) make more sense when considering changes in
configuration data but less sense when the goal is to export a subset
of the operational data off the device in an efficient fashion for
both devices (publishers) and clients (receivers).
Hence, during 2024, the vendors and operators working towards YANG
telemetry solutions agreed to a plan to implement a subset of
[RFC8639] and [RFC8641], including common agreements of features that
are not needed and would not be implemented, and deviations from the
standards for some aspects of encoding YANG data. In addition, the
implementation efforts identified the minimal subset of functionality
needed to support the initial telemetry use cases, and areas of
potential improvement and optimization to the overall YANG Push
telemetry solution (which has been written up as a set of small
internet drafts that augment or extend the base YANG Push solution).
Out of this work, consensus was building to specify a cut down
version of Subscribed Notifications [RFC8639] and YANG Push [RFC8641]
that is both more focussed on the operational telemetry use case, and
is also easier to implement, by relaxing some of the constraints on
consistency on the device, and removing, or simplifying some of the
operational features. This has resulted in this specification, YANG
Push Lite.
The implementation efforts also gave arise to potential improvements
to the protocol and encoding of notification messages.
Wilton, et al. Expires 4 September 2025 [Page 7]
Internet-Draft YANG-Push Lite March 2025
3.2. Complexities in Modelling the Operational State Datastore
The YANG abstraction of a single datastore of related consistent data
works very well for configuration that has a strong requirement to be
self consistent, and that is always updated, and validated, in a
transactional way. But for producers of telemetry data, the YANG
abstraction of a single operational datastore is not really possible
for devices managing a non-trivial quantity of operational data.
Some systems may store their operational data in a single logical
database, yet it is less likely that the operational data can always
be updated in a transactional way, and often for memory efficiency
reasons such a database does not store individual leaves, but instead
semi-consistent records of data at a container or list entry level.
For other systems, the operational information may be distributed
across multiple internal nodes (e.g., linecards), and potentially
many different process daemons within those distributed nodes. Such
systems generally do not, and cannot, exhibit full consistency
[Consistency] of the operational data (which would require
transactional semantics across all daemons and internal nodes), only
offering an eventually consistent [EventualConsistency] view of the
data instead.
In practice, many network devices will manage their operational data
as a combination of some data being stored in a central operational
datastore, and other, higher scale, and potentially more frequently
changing data (e.g., statistics or FIB information) being stored
elsewhere in a more memory efficient and performant way.
3.3. Complexities for Consumers of YANG Push Data
For the consumer of the telemetry data, there is a requirement to
associate a schema with the instance-data that will be provided by a
subscription. One approach is to fetch and build the entire schema
for the device, e.g., by fetching YANG library, and then use the
subscription XPath to select the relevant subtree of the schema that
applies only to the subscription. The problem with this approach is
that if the schema ever changes, e.g., after a software update, then
it is reasonably likely of some changes occurring with the global
device schema even if there are no changes to the schema subtree
under the subscription path. Hence, it would be helpful to identify
and version the schema associated with a particular subscription
path, and also to encoded the instance data relatively to the
subscription path rather than as an absolute path from the root of
the operational datastore.
Wilton, et al. Expires 4 September 2025 [Page 8]
Internet-Draft YANG-Push Lite March 2025
*TODO More needs to be added here, e.g., encoding, on-change
considerations. Splitting subscriptions up.*
This document proposes a new opt-in YANG-Push encoding format to use
instead of the "push-update" and "push-change-update" notifications
defined in [RFC8641].
1. To allow the device to split a subscription into smaller child
subscriptions for more efficient independent and concurrent
processing. I.e., reusing the ideas from
[I-D.ietf-netconf-distributed-notif]. However, all child
subscriptions are still encoded from the same subscription point.
3.3.1. Combined periodic and on-change subscription
Sometimes it is helpful to have a single subscription that covers
both periodic and on-change notifications.
There are two ways in which this may be useful:
1. For generally slow changing data (e.g., a device's physical
inventory), then on-change notifications may be most appropriate.
However, in case there is any lost notification that isn't always
detected, for any reason, then it may also be helpful to have a
slow cadence periodic backup notification of the data (e.g., once
every 24 hours), to ensure that the management systems should
always eventually converge on the current state in the network.
2. For data that is generally polled on a periodic basis (e.g., once
every 10 minutes) and put into a time series database, then it
may be helpful for some data trees to also get more immediate
notifications that the data has changed. Hence, a combined
periodic and on-change subscription, would facilitate more
frequent notifications of changes of the state, to reduce the
need of having to always wait for the next periodic event.
Hence, this document introduces the fairly intuitive "periodic-and-
on-change" update trigger that creates a combined periodic and on-
change subscription, and allows the same parameters to be configured.
For some use cases, e.g., where a time-series database is being
updated, the new encoding format proposed previously may be most
useful.
Wilton, et al. Expires 4 September 2025 [Page 9]
Internet-Draft YANG-Push Lite March 2025
3.4. Relationships to existing RFCs and Internet Drafts
This document, specifying YANG Push Lite, is intended to be a
lightweight alternative for [RFC8639] and [RFC8641], but that also
incorporates various extensions since those RFCs were written. Often
substantial parts of those documents and models have been
incorporated almost verbatim, but modified to fit the YANG Push Lite
functionality and module structure.
Hence, the authors of this draft would like to sincerely thank and
acknowledge the very significant effort put into those RFCs and
drafts by authors, contributors and reviewers. In particular, We
would like to thank the listed authors of these documents: Eric Voit,
Alex Clemm, Alberto Gonzalez Prieto, Einar Nilsen-Nygaard, Ambika
Prasad Tripathy, Balazs Lengyel, Alexander Clemm, Benoit Claise, Qin
Wu, Qiufang Ma, Alex Huang Feng, Thomas Graf, Pierre Francois.
** Note, an alternative approach, but not proposed at this time,
could be to create bis versions of various documents to also cover
YANG Push Lite, e.g.,
[I-D.draft-netana-netconf-yp-transport-capabilities], and perhaps
[RFC9196].**
3.4.1. RFC 8639 and RFC 8641
This document is primarily intended to be a lightweight alternative
for [RFC8639] and [RFC8641], but it intentionally reuses substantial
parts of the design and data model of those RFCs.
YANG Push Lite is defined using a separate module namespace, and
hence can be implemented independently or, if desired, alongside
[RFC8639] and [RFC8641], and the various extensions to YANG Push.
A more complete description of the main differences in YANG Push Lite
compares to [RFC8639] and [RFC8641] is given in
{#DifferencesFromYangPush}.
3.4.2. [I-D.draft-netana-netconf-notif-envelope] and RFC 5277
All of the notifications defined in this specification, i.e., both
the datastore update message and subscription lifecycle update
notifications (Section 10) depend on and use the notification
envelope format defined in [I-D.draft-netana-netconf-notif-envelope].
As such, this specification does not make use of the notification
format defined in [RFC5277]. Of course, devices may also use
[RFC5277] notifications for other YANG notifications, e.g., for the
"NETCONF" event stream defined in [RFC5277].
Wilton, et al. Expires 4 September 2025 [Page 10]
Internet-Draft YANG-Push Lite March 2025
3.4.3. RFC 9196 and
[I-D.draft-netana-netconf-yp-transport-capabilities]
This document uses the capabilities concepts defined in [RFC9196].
In particular, it augments into the ietf-system-capabilities YANG
module, but defines an equivalent alternative capability structure
for the ietf-notification-capabilities YANG module, which defines the
capabilities for YANG Push [RFC8641].
The generic transport capabilities defined in
[I-D.draft-netana-netconf-yp-transport-capabilities] have been
incorporated into the ietf-yp-lite YANG module, to augment YANG Push
Lite transport capabilities and to use the different identities.
3.4.4. [I-D.draft-ietf-netconf-https-notif] and
[I-D.draft-ietf-netconf-udp-notif]
The ietf-yp-lite YANG module has subsumed and extended the
_receivers_ data model defined in the ietf-subscribed-notif-receivers
YANG module defined in [I-D.draft-ietf-netconf-https-notif].
The overall YANG Push Lite solution anticipates and requires new bis
versions of both of these transports documents that augment into the
_receivers/receiver/transport-type_ choice statement, and also
augment the transport identity defined in the ietf-yp-lite data
model.
3.4.5. [I-D.draft-ietf-netconf-distributed-notif]
*TODO. It is likely that some of the base support for distributed
notifications will be incorporated into this draft. If so, add
acknowledgements to the authors.*
4. YANG Push Lite Overview
This document specifies a lightweight telemetry solution that
provides a subscription service for updates to the state and changes
in state from a chosen datastore.
Subscriptions specify when notification messages (also referred to as
_updates_) should be sent, what data to include in the update
records, and where those notifications should be sent.
A YANG Push lite subscription comprises:
* a target datastore for the subscription, where the monitored
subscription data is logically sourced from.
Wilton, et al. Expires 4 September 2025 [Page 11]
Internet-Draft YANG-Push Lite March 2025
* a set of selection filters to choose which datastore nodes from
the target datstore the subscription is monitoring or sampling, as
described in Section 6.
* a choice of how update event notifications for the datastore's
data nodes are triggered. I.e., either periodic sampling of the
current state, on-change event-driven, or both. These are
described in *TODO, add reference*.
* a chosen encoding of the messages, e.g., JSON, or CBOR.
* a set of one or more receivers for which datastore updates and
subscription notifications are sent, as described in Section 8.1;
- for configured subscriptions, the receivers parameters are
configured, and specify transport, receiver, and encoding
parameters.
- for dynamic subscriptions, the receiver uses the same transport
session on which the dynamic subscription has been created.
If a subscription is valid and acceptable to the publisher, and if a
suitable connection can be made to one or more receivers associated
with a subscription, then the publisher will enact the subscription,
periodically sampling or monitoring changes to the chosen datastore's
data nodes that match the selection filter. Push updates are
subsequently sent by the publisher to the receivers, as per the terms
of the subscription.
Subscriptions may be set up in two ways: either through configuration
- or YANG RPCs to create and manage dynamic subscriptions. These two
mechanisms are described in Section 9.
Changes to the state of subscription are notified to receivers as
subscription lifecycle notifications. These are described in
Section 10.
NACM [RFC8341] based access control is used to ensure the receivers
only get access to the information for which they are allowed. This
is further described in Section 14. *TODO Do we need to tie YANG Push
Lite to NACM?*
While the functionality defined in this document is transport
agnostic, transports like the Network Configuration Protocol
(NETCONF) [RFC6241] or RESTCONF [RFC8040] can be used to configure or
dynamically signal subscriptions. In the case of configured
subscription, the transport used for carrying the subscription
notifications is entirely independent from the protocol used to
Wilton, et al. Expires 4 September 2025 [Page 12]
Internet-Draft YANG-Push Lite March 2025
configure the subscription, and other transports, e.g.,
[I-D.draft-ietf-netconf-udp-notif] defines a simple UDP based
transport for Push notifications. Transport considerations are
described in Section 8.2. *TODO the reference to draft-ietf-netconf-
udp-notif isn't right, it wouldn't be that draft, but a -bis version
of it. James is querying whether we need this at all*
*TODO Introduce capabilities and operational monitoring*
This document defines a YANG data model, that includes RPCs and
notifications, for configuring and managing subscriptions and
associated configuration, and to define the format of a _update_
notification message. The YANG model is defined in Section 13.2 and
associated tree view in Section 13.1. The YANG data model defined in
this document conforms to the Network Management Datastore
Architecture defined in [RFC8342].
5. Definitions
This document reuses the terminology defined in [RFC7950], [RFC8341],
[RFC8342], [RFC8639] and [RFC8641].
*TODO, if this document progresses, we should check which of this
terminology we actually use/re-use, and what new terminology should
be introduced in this document. And also an action to check that it
is used consistently.*
The following terms are taken from [RFC8342]:
* _Datastore_: A conceptual place to store and access information.
A datastore might be implemented, for example, using files, a
database, flash memory locations, or combinations thereof. A
datastore maps to an instantiated YANG data tree.
* _Client_: An entity that can access YANG-defined data on a server,
over some network management protocol.
* _Configuration_: Data that is required to get a device from its
initial default state into a desired operational state. This data
is modeled in YANG using "config true" nodes. Configuration can
originate from different sources.
* _Configuration datastore_: A datastore holding configuration.
The following terms are taken from [RFC8639]:
* _Configured subscription_: A subscription installed via
configuration into a configuration datastore.
Wilton, et al. Expires 4 September 2025 [Page 13]
Internet-Draft YANG-Push Lite March 2025
* _Dynamic subscription_: A subscription created dynamically by a
subscriber via a Remote Procedure Call (RPC).
* _Event_: An occurrence of something that may be of interest.
Examples include a configuration change, a fault, a change in
status, crossing a threshold, or an external input to the system.
* _Event occurrence time_: A timestamp matching the time an
originating process identified as when an event happened.
* _Event record_: A set of information detailing an event.
* _Event stream_: A continuous, chronologically ordered set of
events aggregated under some context.
* _Event stream filter_: Evaluation criteria that may be applied
against event records in an event stream. Event records pass the
filter when specified criteria are met.
* _Notification message_: Information intended for a receiver
indicating that one or more events have occurred.
* _Publisher_: An entity responsible for streaming notification
messages per the terms of a subscription.
* _Receiver_: A target to which a publisher pushes subscribed event
records. For dynamic subscriptions, the receiver and subscriber
are the same entity.
* _Subscriber_: A client able to request and negotiate a contract
for the generation and push of event records from a publisher.
For dynamic subscriptions, the receiver and subscriber are the
same entity.
The following terms are taken from [RFC8641]:
* _Datastore node_: A node in the instantiated YANG data tree
associated with a datastore. In this document, datastore nodes
are often also simply referred to as "objects".
* _Datastore node update_: A data item containing the current value
of a datastore node at the time the datastore node update was
created, as well as the path to the datastore node.
* _Datastore subscription_: A subscription to a stream of datastore
node updates.
Wilton, et al. Expires 4 September 2025 [Page 14]
Internet-Draft YANG-Push Lite March 2025
* _Datastore subtree_: A datastore node and all its descendant
datastore nodes.
* _On-change subscription_: A datastore subscription with updates
that are triggered when changes in subscribed datastore nodes are
detected.
* _Periodic subscription_: A datastore subscription with updates
that are triggered periodically according to some time interval.
* _Selection filter_: Evaluation and/or selection criteria that may
be applied against a targeted set of objects.
* _Update record_: A representation of one or more datastore node
updates. In addition, an update record may contain which type of
update led to the datastore node update (e.g., whether the
datastore node was added, changed, or deleted). Also included in
the update record may be other metadata, such as a subscription ID
of the subscription for which the update record was generated. In
this document, update records are often also simply referred to as
"updates".
* _Update trigger_: A mechanism that determines when an update
record needs to be generated.
* _YANG-Push_: The subscription and push mechanism for datastore
updates that is specified in [RFC8641].
This document introduces the following terms:
* _Subscription_: A registration with a publisher, stipulating the
information that one or more receivers wish to have pushed from
the publisher without the need for further solicitation.
* _Subscription Identifier_: A numerical identifier for a configured
or dynamic subscription. Also referred to as the subscription-id.
* _YANG-Push-Lite_: The light weight subscription and push mechanism
for datastore updates that is specified in this document.
All _YANG tree diagrams_ used in this document follow the notation
defined in [RFC8340].
Wilton, et al. Expires 4 September 2025 [Page 15]
Internet-Draft YANG-Push Lite March 2025
6. Subscription paths and selection filters
A key part of a subscription is to select which data nodes should be
monitored, and so a subscription must specify both the selection
filters and the datastore against which these selection filters will
be applied. This information is used to choose, and subsequently
push, _update_ notifications from the publisher's datastore(s) to the
subscription's receiver(s).
Filters can either be defined inline within a configured subscription
(Figure 8), a dynamic subscription's _establish-subscription_ RPC
(Figure 12), or as part of the _datastore-telemetry/filters_
container (Figure 1) which can then be referenced from a configured
or dynamic subscription.
The following selection filter types are included in the YANG Push
Lite data model and may be applied against a datastore:
* _YPaths_: A list of basic YANG path selection filters that defines
a path to a subtree of data nodes in the data tree, with some
simple constraints on keys. See Section 6.1.
* _subtree_: A subtree selection filter identifies one or more
datastore subtrees. When specified, _update_ records will only
include the datastore nodes of selected datastore subtree(s). The
syntax and semantics correspond to those specified in [RFC6241],
Section 6.
* _XPaths_: A list of _XPath_ selection filter is a full XPath
expression that returns a node set. (XPath is a query language
for selecting nodes in an XML document; see [XPATH] for details.)
When specified, updates will only come from the selected datastore
nodes that match the XPath expression.
These filters are used as selectors that define which data nodes fall
within the scope of a subscription. A publisher MUST support basic
path filters, and MAY also support subtree or xpath filters.
XPath itself provides powerful filtering constructs, and care must be
used in filter definition. Consider an XPath filter that only passes
a datastore node when an interface is up. It is up to the receiver
to understand the implications of the presence or absence of objects
in each update.
For both path and xpath based filters, each filter may define a list
of paths/xpaths. Each of these filter paths is processed by the
publisher independently, and if two or more filter paths end up
selecting overlapping data nodes then the publisher MAY notify
Wilton, et al. Expires 4 September 2025 [Page 16]
Internet-Draft YANG-Push Lite March 2025
duplicate values for those data nodes, but the encoded data that is
returned MUST always be syntactically valid, i.e., as per section 5.3
of [RFC8342].
6.1. _YPath_ definition
A _YPath_ represents a simple path into a YANG schema tree, where
some of the list key values may be constrained.
It is encoded in the similar format to the YANG JSON encoding for
instance-identifier, section 6.11 of [RFC7951], except with more
flexibility on the keys, in that keys may be left-out or be bound to
a regular expression filter.
The rules for constructing a YPath are:
* A YPath is a sequence of data tree path segment separated by a '/'
character. If the path starts with a '/' then it is absolute path
from the root of the schema, otherwise it is a relative path,
where the context of the relative path must be declared.
* Constraints on key values may be specified within a single pair of
'[' ']' brackets, where:
- keys may be given in any order, and may be omitted, in which
case they match any value. Key matches are separated by a
comma (,) with optional space character either side.
- key match is given by _<key>=<value>_, with optional space
characters either side of the equals (=), and value is
specified as:
o '<value>', for an exact match of the key's value. Single
quote characters (') must be escaped with a backslash (\).
o r'<reg-expr>', for a regex match of the key value using
[RFC9485], and where the regular-expression is a full match
of the string, i.e, it implicit anchors to the start and end
of the value.
Some examples of YPaths:
* _/ietf-interfaces:interfaces/interface[name='eth0']/ietf-ip:ipv6/
ip_ - which identifies is 'ipv6/ip' data node in the ietf-ip
module for the 'eth0' interface.
Wilton, et al. Expires 4 September 2025 [Page 17]
Internet-Draft YANG-Push Lite March 2025
* _/ietf-interfaces:interfaces/interface[name=r'eth.*']/ietf-
ip:ipv6/ip_ - which identifies all interfaces with a name that
start with "eth".
* _/example:multi-keys-list[first-key='foo', second-key=r'bar.*']_ -
which identifies all entries in the 'multi-keys-list, where the
first-key matches foo, and the second-key starts with bar.
* _/ietf-interfaces:interfaces/interface_ - which identifies the
_interface_ list data node in the ietf-interfaces module for all
interfaces. I.e., the interface list 'name' key is unrestricted.
* _/ietf-interfaces:interfaces/interface[]_ - alternative form of
the previous YPath.
6.2. The "filters" Container
The "filters" container maintains a list of all datastore
subhttps://rgwilton.github.io/draft-yp-observability/draft-wilton-
netconf-yp-observability.html scription filters that persist outside
the lifecycle of a single subscription. This enables predefined
filters that may be referenced by more than one configured or dynamic
subscription.
Below is a tree diagram for the "filters" container. All objects
contained in this tree are described in the YANG module in
Section 13.
module: ietf-yp-lite
+--rw datastore-telemetry!
+--rw filters
+--rw filter* [name]
+--rw name string
+--rw (filter-spec)?
+--:(paths)
| +--rw paths* ypath
+--:(subtree)
| +--rw subtree? <anydata> {ypl:subtree}?
+--:(xpaths)
+--rw xpaths* yang:xpath1.0 {ypl:xpath}?
Figure 1
Wilton, et al. Expires 4 September 2025 [Page 18]
Internet-Draft YANG-Push Lite March 2025
6.3. Decomposing Subscription Filters
In order to address the issues described in Section 3.2, YANG Push
Lite allows for publishers to send subtrees of data nodes in separate
_update_ notifications, rather than requiring that the subscription
data be returned as a single datastore update covering all data nodes
matched by the subscription filter. This better facilitates
publishers that internally group some of their operational data
fields together into larger structures for efficiency (referred to as
an _object_), and avoids the publishers or receivers having to
consume potentially very large notification messages. For example,
each entry in the _/ietf-interfaces:interface/interface_ list could
be represents as an object of data internally within the publisher.
In essence, a client specified subscription filter can be decomposed
by a publisher into more specific, non-overlapping, filters, that are
then used to return the data.
In particular:
1. A Publisher MAY decompose a client specified subscription filter
path into a set of non-overlapping subscription filter paths that
collectively cover the same data. The publisher is allowed to
return data for each of these decomposed subscription filter
paths in separate update messages, and with separate, perhaps
more precise, timestamps.
2. A Publisher MAY split large lists into multiple separate update
messages, each with separate timestamps. E.g., if a device has
10,000 entries in a list, it may return them in a single
response, or it may split them into multiple smaller messages,
perhaps for 500 interfaces at a time. *TODO We need a mechanism
so that the client knows all list entries have been returned, and
hence it can delete stale entries? E.g., something like a
_more_data_ flag.*
3. A Publisher is allowed to generate on-change notifications at an
_object_ level, which hence may contain other associated fields
that may not have changed state, rather than restricting the on-
change notifications strictly to only those specific fields that
have changed state. E.g., if a subscribers registers on the path
_/ietf-interfaces:interfaces/interface[name = *]/oper-status_,
and if interface _eth1_ had a change in the _oper-status_ leaf
state, then rather than just publishing the updated _oper-status_
leaf, the publisher may instead publish all the data associated
with that interface entry object, i.e., everything under _/ietf-
interfaces:interface/interface[name = eth1]_. *TODO Does it have
to be the entire subtree that is published? Do we need to add a
capability annotation to indicate the object publication paths?*
Wilton, et al. Expires 4 September 2025 [Page 19]
Internet-Draft YANG-Push Lite March 2025
To ensure that clients can reasonably process data returned via
decomposed filters then:
1. _update_ notifications MUST indicate the precise subtree of data
that the update message is updating or replacing, i.e., so a
receiver can infer that data nodes no longer being notified by
the publisher have been deleted:
* if we support splitting list entries in multiple updates, then
something like a _more_data_ flag is needed to indicate that
the given update message is not complete.
*TODO We should consider adding a _update-complete_ message
(potentially including an incrementing collection counter) to
indicate when a periodic update has completed for a subscription.*
7. Datastore Event Streams
In YANG Push Lite, a subscription, based on the selected filters,
will generate a ordered stream of datastore _update_ records that is
referred to as an event stream. Each subscription logically has a
different event stream of update records, even if multiple
subscriptions use the same filters to select datastore nodes.
As YANG-defined event records are created by a system, they may be
assigned to one or more streams. The event record is distributed to
a subscription's receiver(s) where (1) a subscription includes the
identified stream and (2) subscription filtering does not exclude the
event record from that receiver.
Access control permissions may be used to silently exclude event
records from an event stream for which the receiver has no read
access. See [RFC8341], Section 3.4.6 for an example of how this
might be accomplished. Note that per Section 2.7 of this document,
subscription state change notifications are never filtered out.
*TODO, filtering and NACM filtering should be dependent on whether it
is a configured or dynamic subscription.*
If subscriber permissions change during the lifecycle of a
subscription and event stream access is no longer permitted, then the
subscription MUST be terminated. *TODO, check this*
Event records SHALL be sent to a receiver in the order in which they
were generated. I.e., the publisher MUST not reorder the events when
enqueuing notifications on the transport session, but there is no
guarantee of delivery order.
Wilton, et al. Expires 4 September 2025 [Page 20]
Internet-Draft YANG-Push Lite March 2025
7.1. Notification Envelope
All notifications in the event stream MUST be encoded using
[I-D.draft-netana-netconf-notif-envelope] to wrap the notification
message, and MUST include the _event-time_, _hostname_, and
_sequence-number_ leaves in all messages.
The following example illustrates a fully encoded _update_
notification that includes the notification envelope and additional
meta-data fields. The _update_ notification, i.e., as defined via
the _notification_ statement in the yang-push-lite YANG module, is
carried in the _contents_ anydata data node.
Wilton, et al. Expires 4 September 2025 [Page 21]
Internet-Draft YANG-Push Lite March 2025
{
"ietf-yp-notification:envelope": {
"event-time": "2024-10-10T08:00:05.22Z",
"hostname": "example-router",
"sequence-number": 3219,
"contents": {
"ietf-yp-lite:update": {
"id": 1011,
"snapshot-type": "periodic",
"observation-time": "2024-10-10T08:00:05.11Z",
"updates": [
{
"target-path": "ietf-interfaces:interfaces/interface",
"data": {
"ietf-interfaces:interfaces": {
"ietf-interfaces:interface": [
{
"name": "eth0",
"type": "iana-if-type:ethernetCsmacd",
"enabled": true,
"ietf-interfaces:oper-status": "up",
"ietf-interfaces:admin-status": "up"
},
{
"name": "eth1",
"type": "iana-if-type:ethernetCsmacd",
"enabled": true,
"ietf-interfaces:oper-status": "up",
"ietf-interfaces:admin-status": "up"
}
]
}
}
}
]
}
}
}
}
Figure 2: Example of update notification including notification
envelope
Wilton, et al. Expires 4 September 2025 [Page 22]
Internet-Draft YANG-Push Lite March 2025
7.2. Event Records
A single _update_ record is used for all datastore notifications. It
is used to report the current state of a set of data nodes at a given
target path for either periodic, on-change, or resync notifications,
and also for on-change notifications to indicate that the data node
at the given target path has been deleted.
The schema for this notifications is given in the following tree
diagram:
+---n update
+--ro id? subscription-id
+--ro path-prefix? string
+--ro snapshot-type? enumeration
+--ro observation-time? yang:date-and-time
+--ro updates* [target-path]
| +--ro target-path string
| +--ro data? <anydata>
+--ro incomplete? empty
Figure 3: 'update' notification
The normative definitions for the notifications fields are given in
the YANG module in Section 13. The fields can be informatively
summarized as:
* _id_ - identifies the subscription the notification relates to.
* _path-prefix_ - identifies the absolute instance-data path to
which all target-paths are data are encoded relative to.
* _snapshot-type_ - this indicates what type of event causes the
update message to be sent. I.e., a periodic collection, an on-
change event, or a resync collection.
* _observation-time_ - the time that the data was sampled, or when
the on-change event occurred that caused the message to be
published.
* _target-path_ - identifies the data node that is being acted on,
either providing the replacement data for, or that data node that
is being deleted.
* _data_ - the full replacement data subtree for the content at the
target-path, encoded from the path-prefix.
Wilton, et al. Expires 4 September 2025 [Page 23]
Internet-Draft YANG-Push Lite March 2025
* _incomplete_ - indicates that the message is incomplete for any
reason. For example, perhaps a periodic subscription expects to
retrieve data from multiple data sources, but one of those data
sources is unavailable. Normally, a receiver can use the absence
of a field in an update message to implicitly indicate that the
field has been deleted, but that should not be inferred if the
incomplete-update leaf is present because not all changes that
have occurred since the last update are actually included with
this update.
As per the structure of the _update_ notification, a single
notification MAY provide updates for multiple target-paths.
7.3. Types of subscription event monitoring
Subscription can either be based on sampling the requested data on a
periodic cadence or being notified when the requested data changes.
In addition, this specification allows for subscriptions that both
notify on-change and also with a periodic cadence, which can help
ensure that the system eventually converges on the right state, even
if on-change notification were somehow lost or mis-processed anywhere
in the data processing pipeline.
The schema for the update-trigger container is given in the following
tree diagram:
module: ietf-yp-lite
+--rw datastore-telemetry!
+--rw subscriptions
+--rw subscription* [id]
+--rw update-trigger
+--rw periodic!
| +--rw period centiseconds
| +--rw anchor-time? yang:date-and-time
+--rw on-change! {on-change}?
+--rw sync-on-start? boolean
Figure 4: 'update-trigger' container
*TODO Minor - is providing the structure from root helpful, or should
this just report the update-trigger container.*
The normative definitions for the update-trigger fields are given in
the _ietf-yp-lite_ YANG module in Section 13. They are also
described in the following sections.
Wilton, et al. Expires 4 September 2025 [Page 24]
Internet-Draft YANG-Push Lite March 2025
7.4. Periodic events
In a periodic subscription, the data included as part of an update
record corresponds to data that could have been read using a
retrieval operation. Only the state that exists in the system at the
time that it is being read is reported, periodic updates never
explicitly indicate whether any data-nodes or list entries have been
deleted. Instead, receivers must infer deletions by the absence of
data during a particular collection event.
For periodic subscriptions, triggered updates will occur at the
boundaries of a specified time interval. These boundaries can be
calculated from the periodic parameters:
* a _period_ that defines the duration between push updates.
* an _anchor-time_; update intervals fall on the points in time that
are a multiple of a _period_ from an _anchor-time_. If an
_anchor-time_ is not provided, then the publisher chooses a
suitable anchor-time, e.g., perhaps the time that the subscription
was first instantiated by the publisher.
The anchor time and period are particularly useful, in fact required,
for when the collected telemetry data is being stored in a time-
series database and the subscription is setup to ensure that each
collection is placed in a separate time-interval bucket.
Periodic update notifications are expected, but not required, to use
a single _target-path_ per _update_ notification.
7.5. On-Change events
In an on-change subscription, _update_ records indicate updated
values or when a monitored data node or list node has been deleted.
An _update_ record is sent whenever a change in the subscribed
information is detected. _update_ records SHOULD be generated at the
same subtree as equivalent periodic subscription rather than only the
specific data node that is on-change notifiable. The goal is to
ensure that the _update_ message contains a consistent set of data on
the subscription path.
Each entry in the _updates_ list identifies a data node (i.e., list
entry, container, leaf or leaf-list), via the _target-path_ that
either has changes is state or has been deleted.
A delete of a specific individual data node or subtree may be
notified in two different ways:
Wilton, et al. Expires 4 September 2025 [Page 25]
Internet-Draft YANG-Push Lite March 2025
* if the data that is being deleted is below the _target-path_ then
the delete is implicit by the publisher returning the current data
node subtree with the delete data nodes missing. I.e., the
receiver must implicitly infer deletion.
* if the data node is being deleted at the target path. E.g., if an
interface is deleted then an entire list entry related to that
interface may be removed. In this case, the _target path_
identifies the list entry that is being deleted, but the data
returned is just an empty object {}, which replaces all the
existing data for that object in the receiver. *TODO, is this
better an a delete flag?*
On-change subscriptions also support the following additional
parameters:
* _sync-on-start_ defines whether or not a complete snapshot of all
subscribed data is sent at the start of a subscription. Such
early synchronization establishes the frame of reference for
subsequent updates.
7.5.1. On-Change Notifiable Datastore Nodes
Publishers are not required to support on-change notifications for
all data nodes, and they may not be able to generate on-change
updates for some data nodes. Possible reasons for this include:
* the value of the datastore node changes frequently (e.g., the in-
octets counter as defined in [RFC8343]),
* small object changes that are frequent and meaningless (e.g., a
temperature gauge changing 0.1 degrees),
* or no implementation is available to generate a notification when
the source variable for a particular data node has changed.
In addition, publishers are not required to notify every change or
value for an on-change monitored data node. Instead, publishers MAY
limit the rate at which changes are reported for a given data node,
i.e., effectively deciding the interval at which an underlying value
is sampled. If a data node changes value and then reverts back to
the original value within a sample interval then the publisher MAY
not detect the change and it would go unreported. However, if the
data node changes to a new value after it has been sampled, then the
change and latest state are reported to the receiver. In addition,
if a client was to query the value (e.g., through a NETCONF get-data
RPC) then they MUST see the same observed value as would be notified.
Wilton, et al. Expires 4 September 2025 [Page 26]
Internet-Draft YANG-Push Lite March 2025
To give an example, if the interface link state reported by hardware
is changing state hundreds of times per second, then it would be
entirely reasonable to limit those interface state changes to a much
lower cadence, e.g., perhaps every 100 milliseconds. In the
particular case of interfaces, there may also be data model specific
forms of more advanced dampening that are more appropriate, e.g.,
that notify interface down events immediately, but rate limit how
quickly the interface is allowed to transition to up state, which
overall acts as a limit on the rate at which the interface state may
change, and hence also act as a limit on the rate at which on-change
notifications could be generated.
The information about what nodes support on-change notifications is
reported using capabilities operational data model. This is further
described in Section 12.
7.5.2. On-Change Considerations
On-change subscriptions allow receivers to receive updates whenever
changes to targeted objects occur. As such, on-change subscriptions
are particularly effective for data that changes infrequently but for
which applications need to be quickly notified, with minimal delay,
whenever a change does occur.
On-change subscriptions tend to be more difficult to implement than
periodic subscriptions. Accordingly, on-change subscriptions may not
be supported by all implementations or for every object.
Whether or not to accept or reject on-change subscription requests
when the scope of the subscription contains objects for which on-
change is not supported is up to the publisher implementation. A
publisher MAY accept an on-change subscription even when the scope of
the subscription contains objects for which on-change is not
supported. In that case, updates are sent only for those objects
within the scope of the subscription that do support on-change
updates, whereas other objects are excluded from update records, even
if their values change. In order for a subscriber to determine
whether objects support on-change subscriptions, objects are marked
accordingly on a publisher. Accordingly, when subscribing, it is the
responsibility of the subscriber to ensure that it is aware of which
objects support on-change and which do not. For more on how objects
are so marked, see Section 3.10. *TODO Is this paragraph and the one
below still the right choice for YANG Push Lite?*
Alternatively, a publisher MAY decide to simply reject an on-change
subscription if the scope of the subscription contains objects for
which on-change is not supported. In the case of a configured
subscription, the publisher MAY suspend the subscription.
Wilton, et al. Expires 4 September 2025 [Page 27]
Internet-Draft YANG-Push Lite March 2025
7.6. Combined periodic and on-change subscriptions
A single subscription may created to generate notifications both when
changes occur and on a periodic cadence. Such subscriptions are
equivalent to having separate periodic and on-change subscriptions on
the same path, except that they share the same subscription-id and
filter paths.
7.7. Streaming Update Examples
*TODO, Generate new JSON based example of a periodic, and delete
messages. Current placeholders are the existing YANG Push
Notifications.*
Figure XXX provides an example of a notification message for a
subscription tracking the operational status of a single Ethernet
interface (per [RFC8343]). This notification message is encoded XML
_W3C.REC-xml-20081126_ over the Network Configuration Protocol
(NETCONF) as per [RFC8640].
<notification
xmlns="urn:ietf:params:xml:ns:netconf:notification:1.0">
<eventTime>2017-10-25T08:00:11.22Z</eventTime>
<push-update xmlns="urn:ietf:params:xml:ns:yang:ietf-yang-push">
<id>1011</id>
<datastore-contents>
<interfaces
xmlns="urn:ietf:params:xml:ns:yang:ietf-interfaces">
<interface>
<name>eth0</name>
<oper-status>up</oper-status>
</interface>
</interfaces>
</datastore-contents>
</push-update>
</notification>
Figure 5: Example 'update' periodic notification
Figure XXX provides an example of an on-change notification message
for the same subscription.
Wilton, et al. Expires 4 September 2025 [Page 28]
Internet-Draft YANG-Push Lite March 2025
<notification
xmlns="urn:ietf:params:xml:ns:netconf:notification:1.0">
<eventTime>2017-10-25T08:22:33.44Z</eventTime>
<push-change-update
xmlns="urn:ietf:params:xml:ns:yang:ietf-yang-push">
<id>89</id>
<datastore-changes>
<yang-patch>
<patch-id>0</patch-id>
<edit>
<edit-id>edit1</edit-id>
<operation>replace</operation>
<target>/ietf-interfaces:interfaces</target>
<value>
<interfaces
xmlns="urn:ietf:params:xml:ns:yang:ietf-interfaces">
<interface>
<name>eth0</name>
<oper-status>down</oper-status>
</interface>
</interfaces>
</value>
</edit>
</yang-patch>
</datastore-changes>
</push-change-update>
</notification>
Figure 6: Example 'update' on-change notification
8. Receivers, Transports, and Encodings
8.1. Receivers
Every subscription is associated with one or more receivers, which
each identify the destination host where all the subscription
notifications are sent. Each receiver has the following associated
properties:
* a _name_ to identify and reference the receiver in configured
subscriptions.
* a _transport_, which identifies the transport protocol to use to
connect with all subscription receivers.
- Optional transport-specific related parameters, e.g., DSCP.
There are likely to be various data nodes related to
establishing appropriate security and encryption.
Wilton, et al. Expires 4 September 2025 [Page 29]
Internet-Draft YANG-Push Lite March 2025
* an _encoding_ to encode all YANG notification messages to the
receiver, i.e., see Section 8.3.
* optional parameters to identify where traffic should egress the
publisher:
- a _source-interface_, which identifies the egress interface to
use from the publisher.
- a _source-address_ address, which identifies the IP address to
stamp on notification messages destined for the receiver.
- a _source-vrf_, which identifies the Virtual Routing and
Forwarding (VRF) instance on which to reach receivers. This
VRF is a network instance as defined in [RFC8529]. Publisher
support for VRFs is optional and advertised using the
_supports-vrf_ feature. *TODO - do we also support inferring
the VRF from the source interface?*
“If none of the above parameters are set, the publisher MAY decide
which interface(s) to source notifications from.
8.1.1. Receivers for Configured Subscriptions
For configured subscriptions, receivers are configured independently
from the subscriptions and then referenced from the subscription.
Configured subscriptions MAY have multiple receivers, but they MUST
have the same encoding. Multiple receivers facilitate redundancy at
the receivers.
Below is a tree diagram for _datastore-telemetry/receivers_
container. All objects contained in this tree are described in the
YANG module in Section 13.2.
Wilton, et al. Expires 4 September 2025 [Page 30]
Internet-Draft YANG-Push Lite March 2025
module: ietf-yp-lite
+--rw datastore-telemetry!
+--rw receivers {configured}?
+--rw receiver* [name]
+--rw name string
+--rw encoding? encoding
+--rw dscp? inet:dscp
+---x reset
+--rw (notification-message-origin)?
| +--:(interface-originated)
| | +--rw source-interface? if:interface-ref
| | {interface-designation}?
| +--:(address-originated)
| +--rw source-vrf? leafref {supports-vrf}?
| +--rw source-address? inet:ip-address-no-zone
+--rw (transport-type)
Figure 7: datastore-telemetry/receivers container
Because there is no explicit association with an existing transport
session, configuration operations include additional parameters
beyond those of dynamic subscriptions. These parameters identify
each receiver, how to connect with that receiver, and possibly
whether the notification messages need to come from a specific egress
interface on the publisher. Receiver-specific transport connectivity
parameters MUST be configured via transport-specific augmentations to
this specification. See Section 2.5.7 for details.
This specification is transport independent. However, supporting a
configured subscription will normally require the establishment of
transport connectivity. Some parameters used for this transport
connectivity establishment are transport specific. As a result, the
YANG module defined in Section 13.2 is not able to directly define
and expose these transport parameters.
It is necessary for an implementation to support the connection
establishment process. To support this function, the YANG data model
defined in this document includes a YANG choice node where transport-
specific parameters for a particular receiver may be augmented. This
node is _/datastore-telemetry/receivers/receiver/transport-type_.
A publisher supporting configured subscriptions must obviously
support at least one YANG data model that augments transport
connectivity parameters on _/datastore-telemetry/receivers/receiver/
transport-type_. For an example of such an augmentation, see
[I-D.draft-ietf-netconf-udp-notif] *TODO, fix this to a UDP bis
document*
Wilton, et al. Expires 4 September 2025 [Page 31]
Internet-Draft YANG-Push Lite March 2025
8.1.2. Receivers for Dynamic Subscriptions
For dynamic subscriptions, each subscription has a single receiver
that is implicit from the host that initiated the _establish-
subscription_ RPC, reusing the same transport session for all the
subscription notifications.
Hence most receiver parameters for a dynamic subscription are
implicitly determined, and cannot be explicitly controlled.
Dynamic subscriptions MUST specify an encoding (see Section 8.3) and
MAY specify DSCP Marking (see Section 8.2.2) for the telemetry
notifications in the _establish-subscription_ RPC (see Figure 12).
8.2. Transports
This document describes a transport-agnostic mechanism for
subscribing to YANG datastore telemetry. Hence, separate
specifications are required to define transports that support YANG
Push Lite. The requirements for these transport specifications are
documented in the following section:
8.2.1. Requirements for Yang Push Lite Transport Specifications
This section provides requirements for any transport specifications
supporting the YANG Push Lite solution presented in this document.
The transport specification MUST provide a YANG module (to be
implemented by publishers) that augments the _datastore-
telemetry/receivers/transport-type_ choice statement with a container
that both identifies the transport and contains all transport
specific parameters.
Using a secure transport is RECOMMENDED. Thus, any transport
specification MUST provide a mechanism to ensure secure communication
between the publisher and receiver in a hostile environment, e.g.,
through the use of transport layer encryption. Transport
specification MAY also specify a mechanism for unencrypted
communications, which can be used when transport layer security is
not required, e.g., if the transport session is being secured via
another mechanism, or when operating within a controlled environment
or test lab.
Any transport specification SHOULD support mutual receiver and
publisher authentication at the transport layer.
Wilton, et al. Expires 4 September 2025 [Page 32]
Internet-Draft YANG-Push Lite March 2025
The transport selected by the subscriber to reach the publisher
SHOULD be able to support multiple "establish-subscription" requests
made in the same transport session.
Any transport specification SHOULD ensure that the receiver
application can be notified of the _subscription-started_ lifecycle
notification before any associated _update_ messages.
A specification for a transport built upon this document can choose
whether to use the same logical channel for the RPCs and the event
records. However, the _update_ records and the subscription state
change notifications MUST be sent on the same transport session.
Any transport specification SHOULD provide an extensible mechanism to
indicate which encodings are supported, e.g., via an IANA registry or
protocol negotiation. Supported encodings for a given transport are
advertised via the ietf-yp-lite-capabilities YANG Model Section 13.4.
Additional transport requirements may be dictated by the choice of
transport used with a subscription.
8.2.2. DSCP Marking
YANG Push Lite supports _dscp_ marking to differentiate
prioritization of notification messages during network transit.
A receiver with a _dscp_ leaf results in a corresponding
Differentiated Services Code Point (DSCP) marking [RFC2474]} being
placed in the IP header of any resulting _update_ notification
messages and subscription state change notifications. A publisher
MUST respect the DSCP markings for subscription traffic egressing
that publisher.
Different DSCP code points require different transport connections.
As a result, where TCP is used, a publisher that supports the "dscp"
feature must ensure that a subscription's notification messages are
returned in a single TCP transport session where all traffic shares
the subscription's "dscp" leaf value. If this cannot be guaranteed,
any "establish-subscription" RPC request SHOULD be rejected with a
"dscp-unavailable" error. *TODO - Is this text still relevant?*
8.3. Encodings
The _update_ notification(Section 7.2) and subscription lifecycle
notifications (Section 10) can be encoded in any format that has a
definition for encoding YANG data. For a given subscription, all
notification messages are encoded using the same encoding.
Wilton, et al. Expires 4 September 2025 [Page 33]
Internet-Draft YANG-Push Lite March 2025
Some IETF standards for YANG encodings known at the time of
publication are:
* JSON, defined in [RFC7951]
* CBOR, defined in [RFC9254], and [RFC9595] for using compressed
schema identifiers (YANG SIDs)
* XML, defined in [RFC7950]
To maximize interoperability, all implementations are RECOMMENDED to
support both JSON and CBOR encodings. Constrained platforms may not
be able to support JSON and hence may choose to only support CBOR
encoding. JSON encoding may not be supported in the scenario that
another encoding becomes the defacto standard (e.g., as JSON has
largely replaced XML as the defacto choice for text based encoding).
Support for the XML encoding and/or CBOR encoding using YANG SIDs is
OPTIONAL.
Encodings are defined in the _ietf-yp-lite.yang_ as YANG identities
that derive from the _encoding_ base identity. Additional encodings
can be defined by defining and implementing new identities that
derive from the _encoding_ base identity, and also advertising those
identities as part of the ietf-yp-lite-capabilities YANG module's
transport capabilities Section 13.4.
For configured subscriptions, the encoding is configured as part of
the receiver configuration (Figure 7).
For dynamic subscriptions, the encoding is selected as part of the
establish-subscription RPC (Figure 12).
*TODO For dynamic subscriptions, Yang Push will infer the encoding
from incoming RPC if not provided. Do we want to preserve the
existing behavior or just be explicit and enforce that an encoding
must always be specified?*
9. Setting up and Managing Subscriptions
Subscriptions can be set up and managed in two ways:
1. Configured Subscriptions - a subscription created and controlled
solely by configuration.
2. Dynamic Subscriptions - a subscription created and controlled via
a YANG RPC from a telemetry receiver.
Wilton, et al. Expires 4 September 2025 [Page 34]
Internet-Draft YANG-Push Lite March 2025
Conformant implementations MUST implement at least one of the two
mechanisms above for establishing and maintaining subscriptions.
Both configured and dynamic subscriptions are represented in the list
_datastore-telemetry/subscriptions/subscription_, and most of the
functionality and behavior of configured and dynamic subscriptions
described in this document is specified to be the same or very
similar. However, they differ in how they are created and in the
associated lifecycle management, described in the following sections:
Additional characteristics differentiating configured from dynamic
subscriptions include the following:
* The lifetime of a dynamic subscription is bound by the transport
session used to establish it. For connection-oriented stateful
transports like NETCONF, the loss of the transport session will
result in the immediate termination of any associated dynamic
subscriptions. For connectionless or stateless transports like
HTTP, a lack of receipt acknowledgment of a sequential set of
notification messages and/or keep-alives can be used to trigger a
termination of a dynamic subscription. Contrast this to the
lifetime of a configured subscription. This lifetime is driven by
relevant configuration being present in the publisher's applied
configuration. Being tied to configuration operations implies
that (1) configured subscriptions can be configured to persist
across reboots and (2) a configured subscription can persist even
when its publisher is fully disconnected from any network. *TODO,
the configured subscription doesn't really persist, since it is
torn down and re-created. This explanation needs to be improved.*
* Configured subscriptions can be modified by any configuration
client with write permission on the configuration of the
subscription. Dynamic subscriptions can only be modified via an
RPC request made by the original subscriber or by a change to
configuration data referenced by the subscription.
Note that there is no mixing and matching of dynamic and configured
operations on a single subscription. Specifically, a configured
subscription cannot be modified or deleted using RPCs defined in this
document. Similarly, a dynamic subscription cannot be directly
modified or deleted by configuration operations. It is, however,
possible to perform a configuration operation that indirectly impacts
a dynamic subscription. By changing the value of a preconfigured
filter referenced by an existing dynamic subscription, the selected
event records passed to a receiver might change.
Wilton, et al. Expires 4 September 2025 [Page 35]
Internet-Draft YANG-Push Lite March 2025
A publisher MAY terminate a dynamic subscription at any time.
Similarly, it MAY decide to temporarily suspend the sending of
notification messages for any dynamic subscription, or for one or
more receivers of a configured subscription. Such termination or
suspension is driven by internal considerations of the publisher.
**TODO, do we want to add text that if a subscription is ever changes
(config or dynamic (e.g., referenced filter)) then the subscription
MUST be terminated and restarted.
9.1. Configured Subscriptions
Configured subscriptions allow the management of subscriptions via
configuration so that a publisher can send notification messages to a
receiver. Support for configured subscriptions is OPTIONAL, with its
availability advertised via the _configured_ YANG feature in the
ietf-yp-lite YANG module Section 13.2.
A configured subscription comprises:
* the target datastore for the subscription, as per [RFC8342].
* a set of selection filters to choose which datastore nodes the
subscription is monitoring or sampling, as described in Section 6
* configuration for how update notifications for the data nodes are
triggered. I.e., either periodic sampling, on-change event-
driven, or both. (*TODO add section reference*)
* a set of associated receivers (as described in Section 8.1) that
specify transport, receiver, and encoding parameters.
Configured subscriptions have several characteristics distinguishing
them from dynamic subscriptions:
* persistence across publisher reboots,
* a reference to receiver, is explicitly configured rather than
being implicitly associated with the transport session, as would
be the case for a dynamic subscription.
* an ability to send notification messages to more than one
receiver. All receivers for a given subscription must use the
same encoding and type of transport (*TODO What about DSCP
settings?*). _Note that receivers are unaware of the existence of
any other receivers._
Wilton, et al. Expires 4 September 2025 [Page 36]
Internet-Draft YANG-Push Lite March 2025
* persistence even when transport or receiver is unavailable. In
this scenario, the publishers will terminate a subscription that
it cannot keep active, but it will periodically attempt to
restablish connection to the receiver and re-activate the
configured subscription.
Multiple configured subscriptions MUST be supportable over a single
transport session. *TODO, James is suggesting that this should be
MAY, either way, I think that this should move to be under the
transport considerations section of the document.*
Below is a tree diagram for the "subscriptions" container. All
objects contained in this tree are described in the YANG module in
Section 13.2. In the operational datastore [RFC8342], the
"subscription" list contains entries both for configured and dynamic
subscriptions.
Wilton, et al. Expires 4 September 2025 [Page 37]
Internet-Draft YANG-Push Lite March 2025
module: ietf-yp-lite
+--rw datastore-telemetry!
+--rw subscriptions
+--rw subscription* [id]
+--rw id subscription-id
+--rw target
| +--rw datastore? identityref
| +--rw (filter)?
| +--:(by-reference)
| | +--rw filter-ref filter-ref
| +--:(within-subscription)
| +--rw (filter-spec)?
| +--:(paths)
| | +--rw paths* ypath
| +--:(subtree)
| | +--rw subtree? <anydata> {ypl:subtree}?
| +--:(xpaths)
| +--rw xpaths* yang:xpath1.0 {ypl:xpath}?
+--rw update-trigger
| +--rw periodic!
| | +--rw period centiseconds
| | +--rw anchor-time? yang:date-and-time
| +--rw on-change! {on-change}?
| +--rw sync-on-start? boolean
+--rw purpose? string {configured}?
+--ro status? subscription-status
+--rw receivers* [name]
| +--rw name
| | -> /datastore-telemetry/receivers/receiver/name
| +--ro encoding? encoding
| +--ro status? receiver-status
| +--ro statistics
| +--ro sent-event-records?
| | yang:zero-based-counter64
| +--ro excluded-event-records?
| yang:zero-based-counter64
+---x reset {configured}?
Figure 8: subscriptions container Tree Diagram
9.1.1. Configured Subscription State Machine
Below is the state machine for a configured subscription on the
publisher. This state machine describes the three states (_valid_,
_invalid_, and _concluded_) as well as the transitions between these
states. Start and end states are depicted to reflect configured
subscription creation and deletion events. The creation or
modification of a configured subscription, referenced filter or
Wilton, et al. Expires 4 September 2025 [Page 38]
Internet-Draft YANG-Push Lite March 2025
receiver initiates an evaluation by the publisher to determine if the
subscription is in the _valid_ state or the _invalid_ state. The
publisher uses its own criteria in making this determination. If in
the _valid_ state, the subscription becomes operational. See (1) in
the diagram below.
**TODO - Add a new 'Active state' to the subscription state machine.
I.e., a subscription is active as long as it has at least one valid
receiver (in some cases this would mean that negotiation with the
receiver is complete, for others, such as simple UDP, is just
requires configuration to be valid.)
Publishers SHOULD NOT send _update_ messages for a subscription that
is not active. I.e., a publisher SHOULD NOT send _update_ messages
before a _subscription-started_ notification or after a
_subscription-terminated_ notification.
Similarly, receivers SHOULD ignore any _update_ messages received for
a subscription that is not active.
.........
: start :-.
:.......: |
create .---modify----<-----.
| | |
V V .-------. .......
.----[evaluate]--no-------->|invalid|-delete->: end :
| '-------' :.....:
|-[re-evaluate]--no--(2)-. ^ ^
| ^ | | |
yes | '->unsupportable delete
| modify (subscription- (subscription-
| | terminated*) terminated*)
| | | |
(1) | (3) (4)
| .---------------------------------------------------.
'-->| valid |
'---------------------------------------------------'
Legend:
Dotted boxes: subscription added or removed via configuration
Dashed boxes: states for a subscription
[evaluate]: decision point on whether the subscription
is supportable
(*): resulting subscription state change notification
Figure 9: Publisher's State Machine for a Configured Subscription
Wilton, et al. Expires 4 September 2025 [Page 39]
Internet-Draft YANG-Push Lite March 2025
A subscription in the _valid_ state may move to the _invalid_ state
in one of two ways. First, it may be modified in a way that fails a
re-evaluation. See (2) in the diagram. Second, the publisher might
determine that the subscription is no longer supportable. This could
be because of an unexpected but sustained increase in an event
stream's event records, degraded CPU capacity, a more complex
referenced filter, or other subscriptions that have usurped
resources. See (3) in the diagram. No matter the case, a
_subscription-terminated_ notification is sent to any receivers in
the _active_ or state. Finally, a subscription may be deleted by
configuration (4).
When a subscription is in the _valid_ state, a publisher will attempt
to connect with all receivers of a configured subscription and
deliver notification messages. Below is the state machine for each
receiver of a configured subscription. This receiver state machine
is fully contained in the state machine of the configured
subscription and is only relevant when the configured subscription is
in the _valid_ state.
.-----------------------------------------------------------.
| valid |
| .----------. .------------. |
| | receiver |---timeout---------------->| receiver | |
| |connecting|<----------------reset--(c)|disconnected| |
| | |<-transport '------------' |
| '----------' loss,reset |
| (a) | |
| subscription- (b) |
| started* .--------. |
| '----->| | |
| |receiver| |
| | active | |
| | | |
| '--------' |
'-----------------------------------------------------------'
Legend:
Dashed boxes that include the word *receiver* show the possible
states for an individual receiver of a valid configured
subscription.
* indicates a subscription state change notification
Figure 10: Receiver State Machine for a Configured Subscription
on a Publisher
Wilton, et al. Expires 4 September 2025 [Page 40]
Internet-Draft YANG-Push Lite March 2025
When a configured subscription first moves to the _valid_ state, the
_state_ leaf of each receiver is initialized to the _connecting_
state. If transport connectivity is not available to any receivers
and there are any notification messages to deliver, a transport
session is established (e.g., per [RFC8071]). Individual receivers
are moved to the _active_ state when a _subscription-started_
subscription state change notification is successfully passed to that
receiver (a). Event records are only sent to active receivers.
Receivers of a configured subscription remain active on the publisher
if both (1) transport connectivity to the receiver is active and (2)
event records are not being dropped due to a publisher's sending
capacity being reached. In addition, a configured subscription's
receiver MUST be moved to the "connecting" state if the receiver is
reset via the "reset" action (b), (c). For more on the "reset"
action, see Section 2.5.5. If transport connectivity cannot be
achieved while in the "connecting" state, the receiver MAY be moved
to the "disconnected" state.
A configured subscription's receiver MUST be moved to the "suspended"
state if there is transport connectivity between the publisher and
receiver but (1) delivery of notification messages is failing due to
a publisher's buffer capacity being reached or (2) notification
messages cannot be generated for that receiver due to insufficient
CPU (d). This is indicated to the receiver by the "subscription-
suspended" subscription state change notification.
A configured subscription's receiver MUST be returned to the "active"
state from the "suspended" state when notification messages can be
generated, bandwidth is sufficient to handle the notification
messages, and a receiver has successfully been sent a "subscription-
resumed" or "subscription-modified" subscription state change
notification (e). The choice as to which of these two subscription
state change notifications is sent is determined by whether the
subscription was modified during the period of suspension.
Modification of a configured subscription is possible at any time. A
"subscription-modified" subscription state change notification will
be sent to all active receivers, immediately followed by notification
messages conforming to the new parameters. Suspended receivers will
also be informed of the modification. However, this notification
will await the end of the suspension for that receiver (e).
9.1.2. Creating a Configured Subscription
Configured subscriptions are created using configuration operations
against the top-level _subscriptions_ subtree.
Wilton, et al. Expires 4 September 2025 [Page 41]
Internet-Draft YANG-Push Lite March 2025
After a subscription is successfully established, the publisher
immediately sends a "subscription-started" subscription state change
notification to each receiver. It is quite possible that upon
configuration, reboot, or even steady-state operations, a transport
session may not be currently available to the receiver. In this
case, when there is something to transport for an active
subscription, transport-specific "call home" operations [RFC8071]
will be used to establish the connection. When transport
connectivity is available, notification messages may then be pushed.
With active configured subscriptions, it is allowable to buffer event
records even after a _subscription-started_ has been sent. However,
if events are lost (rather than just delayed) due to buffer capacity
being reached, a _subscription-terminated_ notification must be sent,
followed by a new subscription-started" notification. These
notifications indicate an event record discontinuity has occurred.
*TODO, to see an example of subscription creation using configuration
operations over NETCONF, see Appendix A.*
9.1.3. Modifying a Configured Subscription
Configured subscriptions may end up being modified due to
configuration changes in the _datastore-telemetry_ container.
If the modification involves adding receivers, then those receivers
are placed in the _connecting_ state. If a receiver is removed, the
subscription state change notification _subscription-terminated_ is
sent to that receiver if that receiver is active or suspended.
*TODO Do we want a common here about tearing down a subscription, or
is having it in the common section sufficient?*
9.1.4. Deleting a Configured Subscription
Configured subscriptions can be deleted via configuration. After a
subscription has been removed from configuration, the publisher MAY
complete their current collection if one is in progress, then the
publisher sends _subscription-terminated_ notification to all of the
subscription's receivers to indicate that the subscription is no
longer active.
*TODO, do we need a comment about closing the transport session if
there are no more subscription to that receiver? Possibly the
Transports section of the document should have a section that
describes the lifecycle of a transport session (or will that end up
differing between configured and dyanmic subscriptions?)*
Wilton, et al. Expires 4 September 2025 [Page 42]
Internet-Draft YANG-Push Lite March 2025
9.1.5. Resetting a Configured Subscription
It is possible that a configured subscription needs to be reset,
e.g., if the receiver wasn't ready to start processing the
subscription notifications. This can be accomplished via invoking
one of the two YANG _reset_ actions in the ietf-yp-lite YANG module:
1. the _reset_ action at _/datastore-
telemetry/subscriptions/subscription/reset_ resets a single
subscription, or
2. the _reset_ action at _/datastore-telemetry/receivers/receiver/
reset_ resets all subscriptions that reference that receiver.
These actions may be useful in cases if a receiver or collector
determines that a configured subscription is not behaving correctly,
and wishes to force a reset of the subscription without modifying the
subscription configuration.
Although the reset action acts at the subscription application level,
the publisher MAY reset any transport session(s) associated with the
subscription or attempt to reconnect to the receiver if a transport
session could not connect. Publishers SHOULD NOT reset the transport
session if the transport session is shared with other subscriptions.
9.2. Dynamic Subscriptions
Dynamic subscriptions, where a subscriber initiates a subscription
negotiation with a publisher via an RPC. If the publisher is able to
serve this request, it accepts it and then starts pushing
notification messages back to the subscriber. If the publisher is
not able to serve it as requested, then an error response is
returned.
Support for dynamic subscriptions is OPTIONAL, with its availability
advertised via the _dynamic_ YANG feature in the ietf-yp-lite YANG
module Section 13.2.
Dynamic subscriptions are managed via protocol operations (in the
form of RPCs, per [RFC7950], Section 7.14) made against targets
located in the publisher.
Wilton, et al. Expires 4 September 2025 [Page 43]
Internet-Draft YANG-Push Lite March 2025
9.2.1. Dynamic Subscription State Machine
Below is the publisher's state machine for a dynamic subscription.
Each state is shown in its own box. It is important to note that
such a subscription doesn't exist at the publisher until an
_establish-subscription_ RPC is accepted. The mere request by a
subscriber to establish a subscription is not sufficient for that
subscription to be externally visible. Start and end states are
depicted to reflect subscription creation and deletion events.
.........
: start :
:.......:
|
establish-subscription
|
|
v
.-----------.
| receiver |
| active |
| |
'-----------'
|
delete/kill-subscription
|
v
.........
: end :
:.......:
Figure 11: Publisher's State Machine for a Dynamic Subscription
Of interest in this state machine are the following:
* Successful "establish-subscription" RPCs move the subscription to
the "active" state.
* A "delete-subscription" or "kill-subscription" RPC will end the
subscription.
* A publisher may choose to end a subscription when there is not
sufficient CPU or bandwidth available to service the subscription.
This is announced to the subscriber via the _subscription-
terminated_ subscription state change notification. The receiver
will need to establish a new subscription.
Wilton, et al. Expires 4 September 2025 [Page 44]
Internet-Draft YANG-Push Lite March 2025
9.2.2. Establishing a Dynamic Subscription
The "establish-subscription" RPC allows a subscriber to request the
creation of a subscription.
The input parameters of the operation are:
o An event stream filter, which may reduce the set of event records
pushed.
If the publisher can satisfy the "establish-subscription" request, it
replies with an identifier for the subscription and then immediately
starts streaming notification messages.
Below is a tree diagram for "establish-subscription". All objects
contained in this tree are described in the YANG module in
Section 13.2.
+---x establish-subscription {dynamic}?
| +---w input
| | +---w target
| | | +---w datastore? identityref
| | | +---w (filter)?
| | | +--:(by-reference)
| | | | +---w filter-ref filter-ref
| | | +--:(within-subscription)
| | | +---w (filter-spec)?
| | | +--:(paths)
| | | | +---w paths* ypath
| | | +--:(subtree)
| | | | +---w subtree? <anydata> {ypl:subtree}?
| | | +--:(xpaths)
| | | +---w xpaths* yang:xpath1.0 {ypl:xpath}?
| | +---w update-trigger
| | | +---w periodic!
| | | | +---w period centiseconds
| | | | +---w anchor-time? yang:date-and-time
| | | +---w on-change! {on-change}?
| | | +---w sync-on-start? boolean
| | +---w encoding encoding
| | +---w dscp? inet:dscp
| +--ro output
| +--ro id subscription-id
Figure 12: establish-subscription YANG RPC
A publisher MAY reject the "establish-subscription" RPC for many
reasons, as described in Section 2.4.6.
Wilton, et al. Expires 4 September 2025 [Page 45]
Internet-Draft YANG-Push Lite March 2025
Below is a tree diagram for "establish-subscription-stream-error-
info" RPC yang-data. All objects contained in this tree are
described in the YANG module in Section 4.
yang-data establish-subscription-stream-error-info
+--ro establish-subscription-stream-error-info
+--ro reason? identityref
+--ro filter-failure-hint? string
Figure 3: "establish-subscription-stream-error-info"
RPC yang-data Tree Diagram
Figure 13: "establish-subscription-stream-error-info" Tree Diagram
9.2.2.1. Negotiation of Subscription Policies
A dynamic subscription request SHOULD be declined if a publisher
determines that it may be unable to provide update records meeting
the terms of an "establish-subscription" RPC request.
9.2.3. Deleting a Dynamic Subscription
The _delete-subscription_ operation permits canceling an existing
dynamic subscription that was established on the same transport
session connecting to the subscriber.
If the publisher accepts the request, which it MUST, if the
subscription-id matches a dynamic subscription established in the
same transport session, then it should stop the subscription and send
a _subscription-terminated_ notification.
The publisher MAY reply back to the client before the subscription
has been terminated, i.e., it may act asynchronously with respect to
the request. The publisher SHOULD NOT send any further events
related to the subscription after the _subscription-terminated_
notification and
*TODO, I think that we should relax this to a SHOULD, but also this
should be common with configured subscriptions, so perhaps not in
this section.* If the publisher accepts the request and the publisher
has indicated success, the publisher SHOULD NOT send any more
notification messages for this subscription.
Wilton, et al. Expires 4 September 2025 [Page 46]
Internet-Draft YANG-Push Lite March 2025
9.2.4. Killing a Dynamic Subscription
The "kill-subscription" RPC operation permits a client to forcibly
end any arbitrary dynamic subscription, identified by subscription-
id, including those not associated with the transport session used
for the RPC. Note, configured subscriptions cannot be killed using
this RPC, and requests to do MUST be rejected.
9.2.5. RPC Failures
Whenever an RPC is unsuccessful, the publisher returns relevant
information as part of the RPC error response. Transport-level error
processing MUST be done before the RPC error processing described in
this section. In all cases, RPC error information returned by the
publisher will use existing transport-layer RPC structures, such as
those seen with NETCONF (Appendix A of [RFC6241]) or RESTCONF
(Section 7.1 of [RFC8040]). These structures MUST be able to encode
subscription-specific errors identified below and defined in this
document's YANG data model.
As a result of this variety, how subscription errors are encoded in
an RPC error response is transport dependent. Valid errors that can
occur for each RPC are as follows:
establish-subscription modify-subscription
---------------------- ----------------------
dscp-unavailable filter-unsupported
encoding-unsupported insufficient-resources
filter-unsupported no-such-subscription
insufficient-resources
delete-subscription kill-subscription
---------------------- ----------------------
no-such-subscription no-such-subscription
To see a NETCONF-based example of an error response from the list
above, see the "no-such-subscription" error response illustrated in
[RFC8640], Figure 10.
There is one final set of transport-independent RPC error elements
included in the YANG data model defined in this document: three yang-
data structures that enable the publisher to provide to the receiver
any error information that does not fit into existing transport-layer
RPC structures. These structures are:
Wilton, et al. Expires 4 September 2025 [Page 47]
Internet-Draft YANG-Push Lite March 2025
1. "establish-subscription-stream-error-info": This MUST be returned
with the leaf "reason" populated if an RPC error reason has not
been placed elsewhere in the transport portion of a failed
"establish-subscription" RPC response. This MUST be sent if
hints on how to overcome the RPC error are included.
2. "modify-subscription-stream-error-info": This MUST be returned
with the leaf "reason" populated if an RPC error reason has not
been placed elsewhere in the transport portion of a failed
"modify-subscription" RPC response. This MUST be sent if hints
on how to overcome the RPC error are included.
3. "delete-subscription-error-info": This MUST be returned with the
leaf "reason" populated if an RPC error reason has not been
placed elsewhere in the transport portion of a failed "delete-
subscription" or "kill-subscription" RPC response.
9.3. Implementation Considerations (from RFC 8639)
*TODO, we should rework this to strings for subscription names
instead*
To support deployments that include both configured and dynamic
subscriptions, it is recommended that the subscription "id" domain be
split into static and dynamic halves. This will eliminate the
possibility of collisions if the configured subscriptions attempt to
set a "subscription-id" that might have already been dynamically
allocated. A best practice is to use the lower half of the "id"
object's integer space when that "id" is assigned by an external
entity (such as with a configured subscription). This leaves the
upper half of the subscription integer space available to be
dynamically assigned by the publisher.
If a subscription is unable to marshal a series of filtered event
records into transmittable notification messages, the receiver should
be terminated with the reason "XXX TBD (Was unsupportable volume)".
For configured subscriptions, operations are performed against the
set of receivers using the subscription "id" as a handle for that
set. But for streaming updates, subscription state change
notifications are local to a receiver. In the case of this
specification, receivers do not get any information from the
publisher about the existence of other receivers. But if a network
operator wants to let the receivers correlate results, it is useful
to use the subscription "id" across the receivers to allow that
correlation. Note that due to the possibility of different access
control permissions per receiver, each receiver may actually get a
different set of event records.
Wilton, et al. Expires 4 September 2025 [Page 48]
Internet-Draft YANG-Push Lite March 2025
9.4. Event Record Delivery
Whether dynamic or configured, once a subscription has been set up,
the publisher streams event records via notification messages per the
terms of the subscription. For dynamic subscriptions, notification
messages are sent over the session used to establish the
subscription. For configured subscriptions, notification messages
are sent over the connections specified by the transport and each
receiver of a configured subscription.
A notification message is sent to a receiver when an event record is
not blocked by either the specified filter criteria or receiver
permissions. This notification message MUST include an <eventTime>
object, as shown in [RFC5277], Section 4. This <eventTime> MUST be
at the top level of a YANG structured event record.
The following example of XML _W3C.REC-xml-20081126_, adapted from
Section 4.2.10 of [RFC7950], illustrates a compliant message:
<notification
xmlns="urn:ietf:params:xml:ns:netconf:notification:1.0">
<eventTime>2007-09-01T10:00:00Z</eventTime>
<link-failure xmlns="https://acme.example.com/system">
<if-name>so-1/2/3.0</if-name>
<if-admin-status>up</if-admin-status>
<if-oper-status>down</if-oper-status>
</link-failure>
</notification>
Figure 10: Subscribed Notification Message
[RFC5277], Section 2.2.1 states that a notification message is to be
sent to a subscriber that initiated a <create-subscription>. With
this document, this statement from [RFC5277] should be more broadly
interpreted to mean that notification messages can also be sent to a
subscriber that initiated an "establish-subscription" or to a
configured receiver that has been sent a "subscription-started".
When a dynamic subscription has been started with "establish-
subscription", respectively, event records matching the newly applied
filter criteria MUST NOT be sent until after the RPC reply has been
sent. *TODO, do we want to keep this?*
When a configured subscription has been started or modified, event
records matching the newly applied filter criteria MUST NOT be sent
until after the "subscription-started" notification has been sent.
Wilton, et al. Expires 4 September 2025 [Page 49]
Internet-Draft YANG-Push Lite March 2025
10. Subscription Lifecycle Notifications
In addition to sending event records to receivers, a publisher also
sends subscription lifecycle state change notifications when
lifecycle events related to subscription management occur.
Subscription state change notifications are generated per
subscription, and are injected into the steam of _update_ messages
for that that subscription. These notifications MUST NOT be dropped
or filtered.
Future extensions, or implementations MAY augment additional fields
into the notification structures. Receivers MUST silently ignore
unexpected fields.
The complete set of subscription state change notifications is
described in the following subsections:
10.1. "subscription-started"
The subscription started notification is sent to a receiver to
indicate that a subscription is active and they may start to receive
_update_ records from the publisher.
The subscription started notification may be sent for any of these
reasons:
1. A new subscription has been configured.
2. A receiver has been added to a configured subscription.
3. The configuration for a configured subscription has been changed,
in which case a _subscription-terminated_ notification should be
sent, followed by a _subscription-started_ notification if the
new configuration is valid.
4. A configured subscription previously failed, and was terminated.
After the publisher has successfully re-established a connection
to the receiver and is starting to send datastore event records
again.
5. A dynamic subscription has been established.
Below is the tree diagram for the _subscription-started_
notification. All data nodes contained in this tree diagram are
described in the YANG module in Section 13.2.
Wilton, et al. Expires 4 September 2025 [Page 50]
Internet-Draft YANG-Push Lite March 2025
+---n subscription-started
| +--ro id subscription-id
| +--ro target
| | +--ro datastore? identityref
| | +--ro (filter)?
| | +--:(by-reference)
| | | +--ro filter-ref filter-ref
| | +--:(within-subscription)
| | +--ro (filter-spec)?
| | +--:(paths)
| | | +--ro paths* ypath
| | +--:(subtree)
| | | +--ro subtree? <anydata> {ypl:subtree}?
| | +--:(xpaths)
| | +--ro xpaths* yang:xpath1.0 {ypl:xpath}?
| +--ro update-trigger
| +--ro periodic!
| | +--ro period centiseconds
| | +--ro anchor-time? yang:date-and-time
| +--ro on-change! {on-change}?
| +--ro sync-on-start? boolean
Figure 14: subscription-started Notification Tree Diagram
*TODO, Should the subscription-started notification report decomposed
subscription paths?*
10.2. "subscription-terminated"
For a receiver, this notification indicates that no further event
records for an active subscription should be expected from the
publisher unless and until a new _subscription-started_ notification
is received.
A _subscription-terminated_ notification SHOULD only be sent by a
publisher to a receiver if a _subscription-started_ notification was
previously sent.
The subscription terminated notification may be sent to a receiver
for any of these reasons:
1. A receiver has been removed from a configured subscription.
2. A configured subscription has been removed.
Wilton, et al. Expires 4 September 2025 [Page 51]
Internet-Draft YANG-Push Lite March 2025
3. The configuration for a configured subscription has been changed,
in which case a _subscription-terminated_ notification should be
sent, followed by a _subscription-started_ notification if the
new configuration is valid.
4. A dynamic subscription was deleted via a "delete-subscription* or
_kill-subscription_ RPC.
5. A subscription has failed for any reason, e.g.,:
* The publisher is no longer able to honor the subscription, due
to resource constraints, or the filter is no longer valid.
* Any transport level buffer to the receiver has become full,
and the hence the publisher is dropping _update_
notifications.
Below is a tree diagram for "subscription-terminated". All objects
contained in this tree are described in the YANG module in
Section 13.2.
+---n subscription-terminated
| +--ro id subscription-id
| +--ro reason identityref
Figure 15: subscription-terminated Notification Tree Diagram
*TODO Augmenting extra fields is better for clients?* The _reason_
datanode identifyref indicates why a subcription has been terminated,
and could be extended with further reasons in future.
10.3. "replay-completed"
*TODO: Need to consider how this works when notifications are split
up. Possibly need to replace this with an opt-in message for a per
collection complete message. I.e., a notification that would be sent
whenever every periodic collection is complete.*
This notification indicates that all of the event records prior to
the current time have been passed to a receiver. It is sent before
any notification messages containing an event record with a timestamp
later than (1) the subscription's start time.
After the "replay-completed" notification has been sent, additional
event records will be sent in sequence as they arise naturally on the
publisher.
Wilton, et al. Expires 4 September 2025 [Page 52]
Internet-Draft YANG-Push Lite March 2025
Below is a tree diagram for "replay-completed". All objects
contained in this tree are described in the YANG module in Section 4.
+---n replay-completed
| +--ro id subscription-id
Figure 16: replay-completed Notification Tree Diagram
11. Performance, Reliability, and Subscription Monitoring
*TODO. Needs updating. Not sure if this text doesn't end up
elsewhere?*
A subscription to updates from a datastore is intended to obviate the
need for polling. However, in order to do so, it is critical that
subscribers can rely on the subscription and have confidence that
they will indeed receive the subscribed updates without having to
worry about updates being silently dropped. In other words, a
subscription constitutes a promise on the side of the publisher to
provide the receivers with updates per the terms of the subscription,
or otherwise notify the receiver if t
Now, there are many reasons why a publisher may at some point no
longer be able to fulfill the terms of the subscription, even if the
subscription had been initiated in good faith. For example, the
volume of datastore nodes may be larger than anticipated, the
interval may prove too short to send full updates in rapid
succession, or an internal problem may prevent objects from being
collected. For this reason, the solution defined in this document
(1) mandates that a publisher notify receivers immediately and
reliably whenever it encounters a situation in which it is unable to
keep the terms of the subscription and (2) provides the publisher
with the option to suspend the subscription in such a case. This
includes indicating the fact that an update is incomplete as part of
a "push-update" or "push-change-update" notification, as well as
emitting a "subscription-suspended" notification as applicable. This
is described further in Section 3.11.1.
A publisher SHOULD reject a request for a subscription if it is
unlikely that the publisher will be able to fulfill the terms of that
subscription request. In such cases, it is preferable to have a
subscriber request a less resource-intensive subscription than to
deal with frequently degraded behavior.
Wilton, et al. Expires 4 September 2025 [Page 53]
Internet-Draft YANG-Push Lite March 2025
The solution builds on [RFC8639]. As defined therein, any loss of an
underlying transport connection will be detected and result in
subscription termination (in the case of dynamic subscriptions) or
suspension (in the case of configured subscriptions), ensuring that
situations where the loss of update notifications would go unnoticed
will not occur.
11.1. Subscription Monitoring
In the operational state datastore, the _datastore-telemetry_
container maintains operational state for all configured and dynamic
subscriptions.
Dynamic subscriptions are only present in the _datastore-
telemetry/subscriptions/subscription_ list when they are active, and
are removed as soon as they are terminated. Whereas configured
subscriptions are present if the list if they are configured,
regardless of whether they are active.
*TODO, should dynamic receivers be listed? Do we need to report per-
receiver stats for dynamic subscriptions?*
The operational state is important for monitoring the health of
subscriptions, receivers, and the overall telemetry subsystem.
This includes:
*TODO, update the YANG model with more useful operational data, and
mostly this section should briefly summarize and refer to the YANG
model. We should also consider what indications to include from
filters that cause a larger amount of internal work but don't
generate a large number of transmitted notifications.*
* per subscription status and counters
* per receiver status and counters
* maybe some indication of the overall load on the telemetry
subsystem, but we need to consider how useful that actually is,
and whether just monitoring the device CPU load and general
performance would be a better indication.
11.2. Robustness and Reliability
It is important that updates as discussed in this document, and on-
change updates in particular, do not get lost. If the loss of an
update is unavoidable, it is critical that the receiver be notified
accordingly.
Wilton, et al. Expires 4 September 2025 [Page 54]
Internet-Draft YANG-Push Lite March 2025
Update records for a single subscription MUST NOT be resequenced
prior to transport.
It is conceivable that, under certain circumstances, a publisher will
recognize that it is unable to include in an update record the full
set of objects desired per the terms of a subscription. In this
case, the publisher MUST act as follows:
* The publisher MUST set the "incomplete-update" flag on any update
record that is known to be missing information.
* The publisher MAY choose to suspend the subscription as per
[RFC8639]. If the publisher does not create an update record at
all, it MUST suspend the subscription.
* When resuming an on-change subscription, the publisher SHOULD
generate a complete patch from the previous update record. If
this is not possible and the "sync-on-start" option is set to
"true" for the subscription, then the full datastore contents MAY
be sent via a "push-update" instead (effectively replacing the
previous contents). If neither scenario above is possible, then
an "incomplete-update" flag MUST be included on the next "push-
change-update".
Note: It is perfectly acceptable to have a series of "push-change-
update" notifications (and even "push-update" notifications) serially
queued at the transport layer awaiting transmission. It is not
required for the publisher to merge pending update records sent at
the same time.
On the receiver side, what action to take when a record with an
"incomplete-update" flag is received depends on the application. It
could simply choose to wait and do nothing. It could choose to
resync, actively retrieving all subscribed information. It could
also choose to tear down the subscription and start a new one,
perhaps with a smaller scope that contains fewer objects.
11.3. Publisher Capacity
It is far preferable to decline a subscription request than to accept
such a request when it cannot be met.
Wilton, et al. Expires 4 September 2025 [Page 55]
Internet-Draft YANG-Push Lite March 2025
Whether or not a subscription can be supported will be determined by
a combination of several factors, such as the subscription update
trigger (on-change or periodic), the period in which to report
changes (one-second periods will consume more resources than one-hour
periods), the amount of data in the datastore subtree that is being
subscribed to, and the number and combination of other subscriptions
that are concurrently being serviced.
12. Conformance and Capabilities
The normative text in this document already indicates which parts of
the specification must or should be implemented for a compliant YANG
Push Lite implementation via the use of [RFC2119] language. It also
sets out some additional related requirements, e.g., on transports
Section 8.2, that add in additional functionality.
Some parts of this specification are optional to implement. Some of
these optional parts can be identified through the use of YANG
Library [RFC8525] specifying the list of implemented YANG modules and
YANG features. But, the broader approach adopted by this
specification is via extending the ietf-system-capabilities YANG
module specified in [RFC9196] to make capability information
available as standard YANG described operational data.
12.1. Capabilities
Publishers SHOULD implement the ietf-system-capabilities YANG module,
defined in [RFC9196], and the ietf-yp-lite-capabilities YANG module,
defined in Section 13.4) that augments ietf-system-capabilities.
The ietf-yp-lite-capabilities module contains capabilities to
indicate what types of subscriptions and transports may be
configured, along with acceptable subscription parameter for given
subtrees.
The schema tree for the ietf-system-capabilities augmented by ietf-
yp-lite-capabilities is given below.
Wilton, et al. Expires 4 September 2025 [Page 56]
Internet-Draft YANG-Push Lite March 2025
module: ietf-system-capabilities
+--ro system-capabilities
+--ro datastore-capabilities* [datastore]
| +--ro datastore
| | -> /yanglib:yang-library/datastore/name
| +--ro per-node-capabilities* []
| +--ro (node-selection)?
| | +--:(node-selector)
| | +--ro node-selector?
| | nacm:node-instance-identifier
| +--ro yplc:datastore-telemetry
| +--ro yplc:periodic-notifications-supported?
| | notification-support
| +--ro (yplc:update-period)?
| | +--:(yplc:minimum-update-period)
| | | +--ro yplc:minimum-update-period? uint32
| | +--:(yplc:supported-update-period)
| | +--ro yplc:supported-update-period* uint32
| +--ro yplc:on-change-supported?
| notification-support
+--ro yplc:datastore-telemetry
+--ro yplc:periodic-notifications-supported?
| notification-support
+--ro (yplc:update-period)?
| +--:(yplc:minimum-update-period)
| | +--ro yplc:minimum-update-period? uint32
| +--:(yplc:supported-update-period)
| +--ro yplc:supported-update-period* uint32
+--ro yplc:on-change-supported?
| notification-support
+--ro yplc:transport
+--ro yplc:transport-capability* [transport-protocol]
+--ro yplc:transport-protocol identityref
+--ro yplc:security-protocol? identityref
+--ro yplc:encoding-format* identityref
Figure 17: YANG tree for ietf-system-capabilities with ietf-yl-
lite-capabilities augmentations.
TODO Do we need to add capabilities to indicate:
1. Which fields are on-change notifiable.
2. At which level _bags_ exist internally (for performance reasons).
3. The points at which subscriptions are decomposed to.
Wilton, et al. Expires 4 September 2025 [Page 57]
Internet-Draft YANG-Push Lite March 2025
12.2. Subscription Content Schema Identification
YANG Module Synchronization
To make subscription requests, the subscriber needs to know the YANG
datastore schemas used by the publisher. These schemas are available
in the YANG library module ietf-yang-library.yang as defined in
[RFC8525]. The receiver is expected to know the YANG library
information before starting a subscription.
The set of modules, revisions, features, and deviations can change at
runtime (if supported by the publisher implementation). For this
purpose, the YANG library provides a simple "yang-library-change"
notification that informs the subscriber that the library has
changed. In this case, a subscription may need to be updated to take
the updates into account. The receiver may also need to be informed
of module changes in order to process updates regarding datastore
*TODO, this section should be updated so that a subscription is
restarted if the schema that it is using changes, and to incorporate
ideas to fingerprint the subscription schema in the subscription-
started notification.*
13. YANG
13.1. ietf-yp-lite YANG tree
This section shows the full tree output for ietf-yp-lite YANG module.
Note, this output does not include support for any transport
configuration, and for any implementation that supports configured
subscriptions using this YANG module then at least one transport
would expect to be configurable.
module: ietf-yp-lite
+--rw datastore-telemetry!
+--rw filters
| +--rw filter* [name]
| +--rw name string
| +--rw (filter-spec)?
| +--:(paths)
| | +--rw paths* ypath
| +--:(subtree)
| | +--rw subtree? <anydata> {ypl:subtree}?
| +--:(xpaths)
| +--rw xpaths* yang:xpath1.0 {ypl:xpath}?
+--rw subscriptions
| +--rw subscription* [id]
Wilton, et al. Expires 4 September 2025 [Page 58]
Internet-Draft YANG-Push Lite March 2025
| +--rw id subscription-id
| +--rw target
| | +--rw datastore? identityref
| | +--rw (filter)?
| | +--:(by-reference)
| | | +--rw filter-ref filter-ref
| | +--:(within-subscription)
| | +--rw (filter-spec)?
| | +--:(paths)
| | | +--rw paths* ypath
| | +--:(subtree)
| | | +--rw subtree? <anydata> {ypl:subtree}?
| | +--:(xpaths)
| | +--rw xpaths* yang:xpath1.0 {ypl:xpath}?
| +--rw update-trigger
| | +--rw periodic!
| | | +--rw period centiseconds
| | | +--rw anchor-time? yang:date-and-time
| | +--rw on-change! {on-change}?
| | +--rw sync-on-start? boolean
| +--rw purpose? string {configured}?
| +--ro status? subscription-status
| +--rw receivers* [name]
| | +--rw name
| | | -> /datastore-telemetry/receivers/receiver/name
| | +--ro encoding? encoding
| | +--ro status? receiver-status
| | +--ro statistics
| | +--ro sent-event-records?
| | | yang:zero-based-counter64
| | +--ro excluded-event-records?
| | yang:zero-based-counter64
| +---x reset {configured}?
+--rw receivers {configured}?
+--rw receiver* [name]
+--rw name string
+--rw encoding? encoding
+--rw dscp? inet:dscp
+---x reset
+--rw (notification-message-origin)?
| +--:(interface-originated)
| | +--rw source-interface? if:interface-ref
| | {interface-designation}?
| +--:(address-originated)
| +--rw source-vrf? leafref {supports-vrf}?
| +--rw source-address? inet:ip-address-no-zone
+--rw (transport-type)
Wilton, et al. Expires 4 September 2025 [Page 59]
Internet-Draft YANG-Push Lite March 2025
rpcs:
+---x establish-subscription {dynamic}?
| +---w input
| | +---w target
| | | +---w datastore? identityref
| | | +---w (filter)?
| | | +--:(by-reference)
| | | | +---w filter-ref filter-ref
| | | +--:(within-subscription)
| | | +---w (filter-spec)?
| | | +--:(paths)
| | | | +---w paths* ypath
| | | +--:(subtree)
| | | | +---w subtree? <anydata> {ypl:subtree}?
| | | +--:(xpaths)
| | | +---w xpaths* yang:xpath1.0 {ypl:xpath}?
| | +---w update-trigger
| | | +---w periodic!
| | | | +---w period centiseconds
| | | | +---w anchor-time? yang:date-and-time
| | | +---w on-change! {on-change}?
| | | +---w sync-on-start? boolean
| | +---w encoding encoding
| | +---w dscp? inet:dscp
| +--ro output
| +--ro id subscription-id
+---x delete-subscription {dynamic}?
| +---w input
| +---w id subscription-id
+---x kill-subscription {dynamic}?
+---w input
+---w id subscription-id
notifications:
+---n replay-completed
| +--ro id subscription-id
+---n update-complete
| +--ro id subscription-id
+---n subscription-started
| +--ro id subscription-id
| +--ro target
| | +--ro datastore? identityref
| | +--ro (filter)?
| | +--:(by-reference)
| | | +--ro filter-ref filter-ref
| | +--:(within-subscription)
| | +--ro (filter-spec)?
| | +--:(paths)
Wilton, et al. Expires 4 September 2025 [Page 60]
Internet-Draft YANG-Push Lite March 2025
| | | +--ro paths* ypath
| | +--:(subtree)
| | | +--ro subtree? <anydata> {ypl:subtree}?
| | +--:(xpaths)
| | +--ro xpaths* yang:xpath1.0 {ypl:xpath}?
| +--ro update-trigger
| +--ro periodic!
| | +--ro period centiseconds
| | +--ro anchor-time? yang:date-and-time
| +--ro on-change! {on-change}?
| +--ro sync-on-start? boolean
+---n subscription-terminated
| +--ro id subscription-id
| +--ro reason identityref
+---n update
+--ro id? subscription-id
+--ro path-prefix? string
+--ro snapshot-type? enumeration
+--ro observation-time? yang:date-and-time
+--ro updates* [target-path]
| +--ro target-path string
| +--ro data? <anydata>
+--ro incomplete? empty
Figure 18: YANG tree for YANG Push Lite Module Tree Output
13.2. ietf-yp-lite YANG Model
This module imports typedefs from [RFC6991], [RFC8343], [RFC8341],
[RFC8529], and [RFC8342]. It references [RFC6241], [XPATH] ("XML
Path Language (XPath) Version 1.0"), [RFC7049], [RFC8259], [RFC7950],
[RFC7951], and [RFC7540].
This YANG module imports typedefs from [RFC6991], identities from
[RFC8342], and the "sx:structure" extension from [RFC8791]. It also
references [RFC6241], [XPATH], and [RFC7950].
<CODE BEGINS> file "ietf-yp-lite.yang#0.1.0"
module ietf-yp-lite {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-yp-lite";
prefix ypl;
import ietf-inet-types {
prefix inet;
reference
"RFC 6991: Common YANG Data Types";
}
Wilton, et al. Expires 4 September 2025 [Page 61]
Internet-Draft YANG-Push Lite March 2025
import ietf-interfaces {
prefix if;
reference
"RFC 8343: A YANG Data Model for Interface Management";
}
import ietf-netconf-acm {
prefix nacm;
reference
"RFC 8341: Network Configuration Access Control Model";
}
import ietf-network-instance {
prefix ni;
reference
"RFC 8529: YANG Data Model for Network Instances";
}
import ietf-yang-structure-ext {
prefix sx;
reference
"RFC 8525: YANG Data Structure Extensions";
}
import ietf-yang-types {
prefix yang;
reference
"RFC 6991: Common YANG Data Types";
}
import ietf-datastores {
prefix ds;
reference
"RFC 8342: Network Management Datastore Architecture (NMDA)";
}
organization
"IETF NETCONF (Network Configuration) Working Group";
contact
"WG Web: <https:/datatracker.ietf.org/wg/netconf/>
WG List: <mailto:netconf@ietf.org>
Author: Robert Wilton
<mailto:rwilton@cisco.com>";
description
"This module contains YANG specifications for YANG-Push lite,
a simplified version of the YANG-Push [RFC 8641] protocol.
The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
'MAY', and 'OPTIONAL' in this document are to be interpreted as
described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
they appear in all capitals, as shown here.
Wilton, et al. Expires 4 September 2025 [Page 62]
Internet-Draft YANG-Push Lite March 2025
Copyright (c) 2025 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Revised BSD License set
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX
(https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself
for full legal notices.";
revision 2024-11-11 {
description
"Initial revision.";
reference
"XXX: YANG Push Lite";
}
/*
* FEATURES
*/
feature configured {
description
"This feature indicates that configuration of subscriptions is
supported.";
}
feature dynamic {
description
"This feature indicates that dynamic establishment of
subscriptions is
supported.";
}
feature interface-designation {
description
"This feature indicates that a publisher supports sourcing all
receiver interactions for a configured subscription from a
single designated egress interface.";
}
feature on-change {
description
"This feature indicates that on-change triggered subscriptions
Wilton, et al. Expires 4 September 2025 [Page 63]
Internet-Draft YANG-Push Lite March 2025
are supported.";
}
feature subtree {
description
"This feature indicates support for YANG subtree filtering.";
reference
"RFC 6241: Network Configuration Protocol (NETCONF),
Section 6";
}
feature supports-vrf {
description
"This feature indicates that a publisher supports VRF
configuration for configured subscriptions. VRF support for
dynamic subscriptions does not require this feature.";
reference
"RFC 8529: YANG Data Model for Network Instances,
Section 6";
}
feature xpath {
description
"This feature indicates support for XPath filtering.";
reference
"XML Path Language (XPath) Version 1.0
(https://www.w3.org/TR/1999/REC-xpath-19991116)";
}
/*
* IDENTITIES
*/
/* Identities for RPC and notification errors */
identity delete-subscription-error {
description
"Base identity for the problem found while attempting to
fulfill either a 'delete-subscription' RPC request or a
'kill-subscription' RPC request.";
}
identity establish-subscription-error {
description
"Base identity for the problem found while attempting to
fulfill an 'establish-subscription' RPC request.";
}
identity subscription-terminated-reason {
Wilton, et al. Expires 4 September 2025 [Page 64]
Internet-Draft YANG-Push Lite March 2025
description
"Base identity for the problem condition communicated to a
receiver as part of a 'subscription-terminated'
notification.";
}
identity dscp-unavailable {
base establish-subscription-error;
description
"The publisher is unable to mark notification messages with
prioritization information in a way that will be respected
during network transit.";
}
identity encoding-unsupported {
base establish-subscription-error;
description
"Unable to encode notification messages in the desired
format.";
}
identity filter-unavailable {
base subscription-terminated-reason;
description
"Referenced filter does not exist. This means a receiver is
referencing a filter that doesn't exist or to which it
does not have access permissions.";
}
identity filter-unsupported {
base establish-subscription-error;
description
"Cannot parse syntax in the filter. This failure can be from
a syntax error or a syntax too complex to be processed by the
publisher.";
}
identity insufficient-resources {
base establish-subscription-error;
description
"The publisher does not have sufficient resources to support
the requested subscription. An example might be that
allocated CPU is too limited to generate the desired set of
notification messages.";
}
identity no-such-subscription {
base delete-subscription-error;
Wilton, et al. Expires 4 September 2025 [Page 65]
Internet-Draft YANG-Push Lite March 2025
base subscription-terminated-reason;
description
"Referenced subscription doesn't exist. This may be as a
result of a nonexistent subscription ID, an ID that belongs to
another subscriber, or an ID for a configured subscription.";
}
identity stream-unavailable {
base subscription-terminated-reason;
description
"Not a subscribable event stream. This means the referenced
event stream is not available for subscription by the
receiver.";
}
identity suspension-timeout {
base subscription-terminated-reason;
description
"Termination of a previously suspended subscription. The
publisher has eliminated the subscription, as it exceeded a
time limit for suspension.";
}
identity unsupportable-volume {
base subscription-terminated-reason;
description
"The publisher does not have the network bandwidth needed to
get the volume of generated information intended for a
receiver.";
}
/* Identities for encodings */
identity configurable-encoding {
description
"If a transport identity derives from this identity, it means
that it supports configurable encodings. An example of a
configurable encoding might be a new identity such as
'encode-cbor'. Such an identity could use
'configurable-encoding' as its base. This would allow a
dynamic subscription encoded in JSON (RFC 8259) to request
that notification messages be encoded via the Concise Binary
Object Representation (CBOR) (RFC 7049). Further details for
any specific configurable encoding would be explored in a
transport document based on this specification.
TODO - Clear up this text or use YANG-CBOR reference";
reference
Wilton, et al. Expires 4 September 2025 [Page 66]
Internet-Draft YANG-Push Lite March 2025
"RFC 8259: The JavaScript Object Notation (JSON) Data
Interchange Format
RFC 7049: Concise Binary Object Representation (CBOR)";
}
identity encoding {
description
"Base identity to represent data encodings.";
}
identity json {
base encoding;
description
"Encode data using JSON as described in RFC 7951.";
reference
"RFC 7951: JSON Encoding of Data Modeled with YANG";
}
identity xml {
base encoding;
description
"Encode data using XML as described in RFC 7950.";
reference
"RFC 7950: The YANG 1.1 Data Modeling Language";
}
identity cbor {
base encoding;
description
"Encode data using CBOR as described in RFC 9245,
without using YANG SIDs";
reference
"RFC 9245: Encoding of Data Modeled with YANG in the
Concise Binary Object Representation (CBOR).";
}
identity cbor-sids {
base encoding;
description
"Encode data using JSON as described in RFC 7951, using YANG
SIDs.";
reference
"RFC 9245: Encoding of Data Modeled with YANG in the
Concise Binary Object Representation (CBOR).
RFC 9595: YANG Schema Item iDentifier (YANG SID).";
}
Wilton, et al. Expires 4 September 2025 [Page 67]
Internet-Draft YANG-Push Lite March 2025
/* Identities for transports */
identity transport {
description
"An identity that represents the underlying mechanism for
passing notification messages.";
}
/*
* TYPEDEFs
*/
typedef ypath {
type string {
length "1..max";
}
description
"A type for YANG instance data paths.";
}
typedef encoding {
type identityref {
base encoding;
}
description
"Specifies a data encoding, e.g., for a data subscription.";
}
typedef subscription-id {
type uint32;
description
"A type for subscription identifiers.";
}
typedef transport {
type identityref {
base transport;
}
description
"Specifies the transport used to send notification messages
to a receiver.";
}
// TODO - Consider changes to list keys or reordering of
// user-ordered lists.
typedef filter-ref {
Wilton, et al. Expires 4 September 2025 [Page 68]
Internet-Draft YANG-Push Lite March 2025
type leafref {
path "/datastore-telemetry/filters/filter/name";
}
description
"This type is used to reference a selection filter.";
}
typedef centiseconds {
type uint32;
description
"A period of time, measured in units of 0.01 seconds.";
}
typedef subscription-type {
type enumeration {
enum configured {
description
"A subscription that is created and managed via
configuration.";
}
enum dynamic {
description
"A subscription that is created and managed via RPC
primitives.";
}
}
description
"Indicate the type of subscription.";
}
typedef subscription-status {
type enumeration {
enum invalid {
description
"The subscription as a whole is unsupportable with its
current parameters.";
}
enum inactive {
description
"The subscription is supportable with its current
parameters, but it is not currently connected to any
connected receivers";
}
enum active {
description
"The subscription is actively running, and is connected
to at least one receiver.
Wilton, et al. Expires 4 September 2025 [Page 69]
Internet-Draft YANG-Push Lite March 2025
A subscription-started notification must have been sent
for a subscription to be in this state, and the receiver
will receive update notifications, as per the
update-trigger selection.";
}
}
description
"Indicates the status of a subscription";
}
typedef receiver-status {
type enumeration {
enum disconnected {
description
"The publish is not currently connected to the receiver.
Nornally, this is because there are no active
subscriptions for this receiver.";
}
enum connecting {
description
"The publisher is actively trying to connect to the
receiver. This implies that there is at least one active
subscription for this receiver.
A receiver in connecting state may indicate that the
transport or associated security session could not be
established, and the publisher is periodically trying to
establish the connection.";
}
enum connected {
description
"The publisher has successfully connected to the receiver
and at least one active subscription is using this
receiver.";
}
}
description
"Indicates the status of a receiver";
}
/*
* GROUPINGS
*/
grouping dscp {
description
"This grouping describes QoS information concerning a
Wilton, et al. Expires 4 September 2025 [Page 70]
Internet-Draft YANG-Push Lite March 2025
subscription. This information is passed to lower layers
for transport prioritization and treatment.";
leaf dscp {
type inet:dscp;
default "0";
description
"The desired network transport priority level. This is the
priority set on notification messages encapsulating the
results of the subscription. This transport priority is
shared for all receivers of a given subscription.";
}
}
grouping filter-types {
description
"This grouping defines the types of selectors for objects
from a datastore.";
choice filter-spec {
description
"The content filter specification for this request.";
leaf-list paths {
type ypath;
description
"A basic path filter that allows wildcard, regex, or
fixed value for list keys. Each format is TODO";
}
anydata subtree {
if-feature "ypl:subtree";
description
"This parameter identifies the portions of the
target datastore to retrieve.";
reference
"RFC 6241: Network Configuration Protocol (NETCONF),
Section 6";
}
leaf-list xpaths {
if-feature "ypl:xpath";
type yang:xpath1.0;
description
"This parameter contains an XPath expression identifying
the portions of the target datastore to retrieve.
If the expression returns a node set, all nodes in the
node set are selected by the filter. Otherwise, if the
expression does not return a node set, the filter
doesn't select any nodes.
Wilton, et al. Expires 4 September 2025 [Page 71]
Internet-Draft YANG-Push Lite March 2025
The expression is evaluated in the following XPath
context:
o The set of namespace declarations is the set of prefix
and namespace pairs for all YANG modules implemented
by the server, where the prefix is the YANG module
name and the namespace is as defined by the
'namespace' statement in the YANG module.
If the leaf is encoded in XML, all namespace
declarations in scope on the 'stream-xpath-filter'
leaf element are added to the set of namespace
declarations. If a prefix found in the XML is
already present in the set of namespace declarations,
the namespace in the XML is used.
o The set of variable bindings is empty.
o The function library is comprised of the core
function library and the XPath functions defined in
Section 10 in RFC 7950.
o The context node is the root node of the target
datastore.";
reference
"XML Path Language (XPath) Version 1.0
(https://www.w3.org/TR/1999/REC-xpath-19991116)
RFC 7950: The YANG 1.1 Data Modeling Language,
Section 10";
}
}
}
grouping update-policy {
description
"This grouping describes the susbcription update policy";
container update-trigger {
description
"This container describes all conditions under which
subscription update messages are generated";
container periodic {
presence "indicates a periodic subscription";
description
"The publisher is requested to periodically notify the
receiver regarding the current values of the datastore
as defined by the selection filter.";
Wilton, et al. Expires 4 September 2025 [Page 72]
Internet-Draft YANG-Push Lite March 2025
leaf period {
type centiseconds;
mandatory true;
description
"Duration of time that should occur between periodic
push updates, in units of 0.01 seconds.";
}
leaf anchor-time {
type yang:date-and-time;
description
"Designates a timestamp before or after which a series
of periodic push updates are determined. The next
update will take place at a point in time that is a
multiple of a period from the 'anchor-time'.
For example, for an 'anchor-time' that is set for the
top of a particular minute and a period interval of a
minute, updates will be sent at the top of every
minute that this subscription is active.";
}
}
container on-change {
if-feature "on-change";
presence "indicates an on-change subscription";
description
"The publisher is requested to notify the receiver
regarding changes in values in the datastore subset as
defined by a selection filter.";
leaf sync-on-start {
type boolean;
default "true";
description
"When this object is set to 'false', (1) it restricts an
on-change subscription from sending 'push-update'
notifications and (2) pushing a full selection per the
terms of the selection filter MUST NOT be done for
this subscription. Only updates about changes
(i.e., only 'push-change-update' notifications)
are sent. When set to 'true' (the default behavior),
in order to facilitate a receiver's synchronization,
a full update is sent, via a 'push-update' notification,
when the subscription starts. After that,
'push-change-update' notifications are exclusively sent,
unless the publisher chooses to resync the subscription
via a new 'push-update' notification.";
}
}
}
Wilton, et al. Expires 4 September 2025 [Page 73]
Internet-Draft YANG-Push Lite March 2025
}
grouping subscription-common {
description
"Common settings that are shared between dynamic and
configured subscriptions.";
container target {
description
"Identifies the source of information against which a
subscription is being applied as well as specifics on the
subset of information desired from that source.";
leaf datastore {
type identityref {
base ds:datastore;
}
default "ds:operational";
description
"Datastore from which to retrieve data, defaults to
operational";
}
choice filter {
description
"The source of the selection filter applied to the
subscription. This will either (1) come referenced from
a global list or (2) be provided in the subscription
itself.";
case by-reference {
description
"Incorporates a filter that has been configured
separately.";
leaf filter-ref {
type filter-ref;
mandatory true;
description
"References an existing selection filter that is to be
applied to the subscription.";
}
}
case within-subscription {
description
"A local definition allows a filter to have the same
lifecycle as the subscription.";
uses filter-types;
}
}
}
Wilton, et al. Expires 4 September 2025 [Page 74]
Internet-Draft YANG-Push Lite March 2025
uses update-policy;
}
/*
* RPCs
*/
rpc establish-subscription {
if-feature "dynamic";
description
"This RPC allows a subscriber to create (and possibly
negotiate) a subscription on its own behalf. If successful,
the subscription remains in effect for the duration of the
subscriber's association with the publisher or until the
subscription is terminated. If an error occurs or the
publisher cannot meet the terms of a subscription, an RPC
error is returned, and the subscription is not created.
In that case, the RPC reply's 'error-info' MAY include
suggested parameter settings that would have a higher
likelihood of succeeding in a subsequent
'establish-subscription' request.";
input {
uses subscription-common;
leaf encoding {
type encoding;
mandatory true;
description
"The encoding to use for the subscription notifications.";
}
uses dscp;
}
output {
leaf id {
type subscription-id;
mandatory true;
description
"Identifier used for this subscription.";
}
}
}
sx:structure establish-subscription-stream-error-info {
container establish-subscription-stream-error-info {
description
Wilton, et al. Expires 4 September 2025 [Page 75]
Internet-Draft YANG-Push Lite March 2025
"If any 'establish-subscription' RPC parameters are
unsupportable against the event stream, a subscription
is not created and the RPC error response MUST indicate the
reason why the subscription failed to be created. This
yang-data MAY be inserted as structured data in a
subscription's RPC error response to indicate the reason for
the failure. This yang-data MUST be inserted if hints are
to be provided back to the subscriber.";
leaf reason {
type identityref {
base establish-subscription-error;
}
description
"Indicates the reason why the subscription has failed to
be created to a targeted event stream.";
}
leaf filter-failure-hint {
type string;
description
"Information describing where and/or why a provided
filter was unsupportable for a subscription. The
syntax and semantics of this hint are
implementation specific.";
}
}
}
rpc delete-subscription {
if-feature "dynamic";
description
"This RPC allows a subscriber to delete a subscription that
was previously created by that same subscriber using the
'establish-subscription' RPC.
Only subscriptions that were created using
'establish-subscription' from the same origin as this RPC
can be deleted via this RPC. // TODO - Why same origin?
If an error occurs, the server replies with an 'rpc-error'
where the 'error-info' field MAY contain a
'delete-subscription-error-info' structure.";
input {
leaf id {
type subscription-id;
mandatory true;
description
"Identifier of the dynamic subscription that is to be
deleted.";
Wilton, et al. Expires 4 September 2025 [Page 76]
Internet-Draft YANG-Push Lite March 2025
}
}
}
rpc kill-subscription {
if-feature "dynamic";
nacm:default-deny-all;
description
"This RPC allows an operator to delete a dynamic subscription
without restrictions on the originating subscriber or
underlying transport session.
Only dynamic subscriptions, i.e., those that were created
using 'establish-subscription', may be deleted via this RPC.
If an error occurs, the server replies with an 'rpc-error'
where the 'error-info' field MAY contain a
'delete-subscription-error-info' structure.";
input {
leaf id {
type subscription-id;
mandatory true;
description
"Identifier of the dynamic subscription that is to be
deleted.";
}
}
}
sx:structure delete-subscription-error-info {
container delete-subscription-error-info {
description
"If a 'delete-subscription' RPC or a 'kill-subscription' RPC
fails, the subscription is not deleted and the RPC error
response MUST indicate the reason for this failure. This
yang-data MAY be inserted as structured data in a
subscription's RPC error response to indicate the reason
for the failure.";
leaf reason {
type identityref {
base delete-subscription-error;
}
mandatory true;
description
"Indicates the reason why the subscription has failed to be
deleted.";
}
}
Wilton, et al. Expires 4 September 2025 [Page 77]
Internet-Draft YANG-Push Lite March 2025
}
/*
* NOTIFICATIONS
*/
// TODO - Need to signal when an initial replay has completed, or
// possibly when any period subscription has completed.
// TODO - Need to think about list key entries that are no longer
// present.
notification replay-completed {
//ypl:subscription-state-notification;
//if-feature "replay";
description
"This notification is sent to indicate that all of the replay
notifications have been sent.";
leaf id {
type subscription-id;
mandatory true;
description
"This references the affected subscription.";
}
}
notification update-complete {
//ypl:subscription-state-notification;
//if-feature "replay";
description
"This notification indicates the end of a periodic collection,
and can be used to purge old state";
leaf id {
type subscription-id;
mandatory true;
description
"This references the affected subscription.";
}
}
notification subscription-started {
//ypl:subscription-state-notification;
description
"This notification indicates that a configured subscription
has started and notifications will now be sent.";
leaf id {
type subscription-id;
mandatory true;
description
"This references the affected subscription.";
Wilton, et al. Expires 4 September 2025 [Page 78]
Internet-Draft YANG-Push Lite March 2025
}
uses subscription-common;
}
notification subscription-terminated {
//ypl:subscription-state-notification;
description
"This notification indicates that a subscription has been
terminated.";
leaf id {
type subscription-id;
mandatory true;
description
"This references the affected subscription.";
}
leaf reason {
type identityref {
base subscription-terminated-reason;
}
mandatory true;
description
"Identifies the condition that resulted in the
termination.";
}
}
notification update {
description
"This notification contains a push update that in turn
contains data subscribed to via a subscription. In the case
of a periodic subscription, this notification is sent for
periodic updates. It can also be used for synchronization
updates of an on-change subscription. This notification
shall only be sent to receivers of a subscription. It does
not constitute a general-purpose notification that would be
subscribable as part of the NETCONF event stream by any
receiver.";
leaf id {
type subscription-id;
description
"This references the subscription that drove the
notification to be sent.";
}
leaf path-prefix {
type string;
description
"Specifies the common prefix that all other paths and data
Wilton, et al. Expires 4 September 2025 [Page 79]
Internet-Draft YANG-Push Lite March 2025
are encoded relative to.
TODO - This should be a JSONified instance data path.";
}
leaf snapshot-type {
type enumeration {
enum "periodic" {
description
"The update message is due to a periodic update.";
}
enum "on-change-update" {
description
"The update message is due to an on-change update. This
means that one or more fields have changed under the
snapshot path.
TODO - Split this into a on-change-delete msg?";
}
enum "on-change-delete" {
description
"The update message is due to an on-change event where
the data node at the target path has been delete.";
}
enum "resync" {
description
"This indicates that the update is to resynchronize the
state, e.g., after a subscription started notification.
Ideally, the resync message SHOULD be the first
notification sent when a subscription has started, but
it is not gauranteed or required to be the first
(e.g., if an on-change event occurs).
These messages can be used to ensure that all state
has been sent to the client, and can be used to purge
stale data.
TODO - In the distributed notification case, need a
notification to indicate that all child subscriptions
have been sent.";
}
}
description
"This indicates the type of notification message that is
being sent.";
}
Wilton, et al. Expires 4 September 2025 [Page 80]
Internet-Draft YANG-Push Lite March 2025
// Could add observation time here.
leaf observation-time {
type yang:date-and-time;
description
"The time that the update was observed by the publisher.";
}
list updates {
key "target-path";
description
"This list contains the updated data. It constitutes a
snapshot at the time of update of the set of data that has
been subscribed to. The snapshot corresponds to the same
snapshot that would be returned in a corresponding 'get'
operation with the same selection filter parameters
applied.";
leaf target-path {
type string;
description
"The target path of the data that is being replaced, i.e.,
updated or deleted. The path is given relative to the
path-prefix.";
}
anydata data {
description
"This contains the updated data. It constitutes a
snapshot at the time of update of the set of data that has
been subscribed to. The snapshot corresponds to the same
snapshot that would be returned in a corresponding 'get'
operation with the same selection filter parameters
applied.
For an on-change delete notification, the
datastore-snapshot will be absent for the given target
path.
The snapshot is encoded relative to the path-prefix.";
}
}
leaf incomplete {
type empty;
description
"This is a flag that indicates that not all datastore nodes
subscribed to are included with this update. Receivers of
this data SHOULD NOT assume that any missing data has been
Wilton, et al. Expires 4 September 2025 [Page 81]
Internet-Draft YANG-Push Lite March 2025
implicitly deleted.";
}
}
/*
* DATA NODES
*/
container datastore-telemetry {
presence "Enables datastore telemetry";
description
"YANG Push Lite Datastore Telemetry Configuration and State.";
container filters {
description
"Contains a list of configurable filters that can be applied
to subscriptions. This facilitates the reuse of complex
filters once defined.";
list filter {
key "name";
description
"A list of preconfigured filters that can be applied
to datastore subscriptions.";
leaf name {
type string;
description
"A unique name to identify the selection filters.";
}
uses filter-types;
}
}
container subscriptions {
description
"Contains the list of currently active subscriptions, i.e.,
subscriptions that are currently in effect, used for
subscription management and monitoring purposes. This
includes subscriptions that have been set up via
RPC primitives as well as subscriptions that have been
established via configuration.";
list subscription {
key "id";
description
"The identity and specific parameters of a subscription.
Subscriptions in this list can be created using a control
channel or RPC or can be established through configuration.
If the 'kill-subscription' RPC or configuration operations
are used to delete a subscription, a
Wilton, et al. Expires 4 September 2025 [Page 82]
Internet-Draft YANG-Push Lite March 2025
'subscription-terminated' message is sent to any active or
suspended receivers.";
leaf id {
type subscription-id;
description
"Identifier of a subscription; unique in a given
publisher.";
}
uses subscription-common;
leaf purpose {
if-feature "configured";
type string;
description
"Open text allowing a configuring entity to embed the
originator or other specifics of this subscription.";
}
leaf status {
type subscription-status;
config false;
description
"The presence of this leaf indicates that the
subscription originated from configuration, not through
a controlchannel or RPC. The value indicates the state
of the subscription as established by the publisher.";
}
list receivers {
key "name";
min-elements 1;
description
"A host intended as a recipient for the notification
messages of a subscription. For configured
subscriptions, transport-specific network parameters
(or a leafref to those parameters) may be augmented to a
specific receiver in this list.";
leaf name {
type leafref {
path "/datastore-telemetry/receivers/receiver/name";
}
description
"Identifies a unique receiver for a subscription.";
}
leaf encoding {
type encoding;
config false;
Wilton, et al. Expires 4 September 2025 [Page 83]
Internet-Draft YANG-Push Lite March 2025
description
"The type of encoding for notification messages.";
}
leaf status {
type receiver-status;
config false;
description
"Specifies the connection status of the receiver.
I.e., whether a conenction has been sucessfully
established";
}
container statistics {
config false;
description
"Statistics related to the number of messages sent to
the receiver.";
leaf sent-event-records {
type yang:zero-based-counter64;
config false;
description
"The number of event records sent to the receiver.
The count is initialized when a dynamic
subscription is established or when a configured
receiver transitions to the 'valid' state.";
}
leaf excluded-event-records {
type yang:zero-based-counter64;
config false;
description
"The number of event records explicitly removed via
either an event stream filter or an access control
filter so that they are not passed to a receiver.
This count is set to zero each time
'sent-event-records' is initialized.";
}
}
}
action reset {
if-feature "configured";
description
"Reset the subscription.
This action will cause a new subscription-started
message to be sent for the subscription";
Wilton, et al. Expires 4 September 2025 [Page 84]
Internet-Draft YANG-Push Lite March 2025
}
}
}
container receivers {
if-feature "configured";
description
"A container for all instances of configured receivers.";
list receiver {
key "name";
leaf name {
type string;
description
"An arbitrary but unique name for this receiver
instance.";
}
leaf encoding {
/* when 'not(../transport) or derived-from(../transport,
"ypl:configurable-encoding")';*/
type encoding;
description
"The type of encoding for notification messages. For a
dynamic subscription, if not included as part of an
'establish-subscription' RPC, the encoding will be
populated with the encoding used by that RPC. For a
configured subscription, if not explicitly configured,
the encoding will be the default encoding for an
underlying transport.";
}
uses dscp;
action reset {
description
"Resets all configured subscriptions that reference
this receiver.
This action is directly equivalent to invoking the
'reset' action on all subscriptions that references
this receiver configuration.";
}
choice notification-message-origin {
description
"Identifies the egress interface on the publisher
from which notification messages are to be sent.";
Wilton, et al. Expires 4 September 2025 [Page 85]
Internet-Draft YANG-Push Lite March 2025
case interface-originated {
description
"When notification messages are to egress a specific,
designated interface on the publisher.";
leaf source-interface {
if-feature "interface-designation";
type if:interface-ref;
description
"References the interface for notification
messages.";
}
}
case address-originated {
description
"When notification messages are to depart from a
publisher using a specific originating address and/or
routing context information.";
leaf source-vrf {
if-feature "supports-vrf";
type leafref {
path
'/ni:network-instances/ni:network-instance/'
+ 'ni:name';
}
description
"VRF from which notification messages should egress a
publisher.";
}
leaf source-address {
type inet:ip-address-no-zone;
description
"The source address for the notification messages.
If a source VRF exists but this object doesn't, a
publisher's default address for that VRF must
be used.";
}
}
}
choice transport-type {
mandatory true;
description
"Choice of different types of transports used to
send notifications. The 'case' statements must
be augmented in by other modules.";
}
description
Wilton, et al. Expires 4 September 2025 [Page 86]
Internet-Draft YANG-Push Lite March 2025
"A list of all receiver instances.";
}
}
}
}
<CODE ENDS>
Figure 19: YANG module ietf-yp-lite
13.3. ietf-yp-lite-capabilities YANG tree
This section shows the tree output for ietf-yp-lite-capabilities YANG
module, which augments the ietf-system-capabilities YANG module
[RFC9196].
module: ietf-yp-lite-capabilities
augment /sysc:system-capabilities:
+--ro datastore-telemetry
+--ro periodic-notifications-supported? notification-support
+--ro (update-period)?
| +--:(minimum-update-period)
| | +--ro minimum-update-period? uint32
| +--:(supported-update-period)
| +--ro supported-update-period* uint32
+--ro on-change-supported? notification-support
+--ro transport
+--ro transport-capability* [transport-protocol]
+--ro transport-protocol identityref
+--ro security-protocol? identityref
+--ro encoding-format* identityref
augment /sysc:system-capabilities/sysc:datastore-capabilities
/sysc:per-node-capabilities:
+--ro datastore-telemetry
+--ro periodic-notifications-supported? notification-support
+--ro (update-period)?
| +--:(minimum-update-period)
| | +--ro minimum-update-period? uint32
| +--:(supported-update-period)
| +--ro supported-update-period* uint32
+--ro on-change-supported? notification-support
Figure 20: YANG tree for YANG Push Lite Capabilities Module Tree
Output
Wilton, et al. Expires 4 September 2025 [Page 87]
Internet-Draft YANG-Push Lite March 2025
13.4. ietf-yp-lite-capabiltiies YANG Model
This module imports typedefs from the yang-push-lite YANG module.
This module augments the ietf-system-capabilities YANG module
[RFC9196].
<CODE BEGINS> file "ietf-yp-lite-capabilities.yang#0.1.0"
module ietf-yp-lite-capabilities {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-yp-lite-capabilities";
prefix yplc;
import ietf-system-capabilities {
prefix sysc;
reference
"RFC 9196: YANG Modules Describing Capabilities for Systems
and Datastore Update Notifications";
}
import ietf-yp-lite {
prefix ypl;
reference
"RFC XXX: YANG Push Lite";
}
organization
"IETF NETCONF (Network Configuration) Working Group";
contact
"WG Web: <https:/datatracker.ietf.org/wg/netconf/>
WG List: <mailto:netconf@ietf.org>
Author: Robert Wilton
<mailto:rwilton@cisco.com>";
description
"This module contains YANG specifications for YANG-Push lite.
The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
'MAY', and 'OPTIONAL' in this document are to be interpreted as
described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
they appear in all capitals, as shown here.
Copyright (c) 2025 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Revised BSD License set
Wilton, et al. Expires 4 September 2025 [Page 88]
Internet-Draft YANG-Push Lite March 2025
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX
(https://www.rfc-editor.org/info/rfcXXXX); see the RFC itself
for full legal notices.";
revision 2024-11-11 {
description
"Initial revision.";
reference
"XXX: YANG Push Lite";
}
/*
* IDENTITIES
*/
identity security-protocol {
description
"Identity for security protocols.";
}
identity tls12 {
base security-protocol;
description
"Indicates TLS Protocol Version 1.2. TLS 1.2 is obsolete,
and thus it is NOT RECOMMENDED to enable this feature.";
reference
"RFC 5246: The Transport Layer Security (TLS) Protocol
Version 1.2";
}
identity tls13 {
base security-protocol;
description
"Indicates TLS Protocol Version 1.3.";
reference
"RFC 8446: The Transport Layer Security (TLS)
Protocol Version 1.3";
}
identity dtls12 {
base security-protocol;
description
"Indicates DTLS Protocol Version 1.2. TLS 1.2 is obsolete,
and thus it is NOT RECOMMENDED to enable this feature.";
Wilton, et al. Expires 4 September 2025 [Page 89]
Internet-Draft YANG-Push Lite March 2025
reference
"RFC 6347: The Datagram Transport Layer Security (TLS) Protocol
Version 1.2";
}
identity dtls13 {
base security-protocol;
description
"Indicates DTLS Protocol Version 1.3.";
reference
"RFC 9147: The Datagram Transport Layer Security (TLS)
Protocol Version 1.3";
}
identity ssh {
base security-protocol;
description
"Indicates SSH.";
}
grouping yp-lite-capabilities {
description
"Capabilities related to YANG Push Lite subscriptions
and notifications";
container datastore-telemetry {
description
"Capabilities related to YANG Push List subscriptions
and notifications";
typedef notification-support {
type bits {
bit config-changes {
description
"The publisher is capable of sending
notifications for 'config true' nodes for the
relevant scope and subscription type.";
}
bit state-changes {
description
"The publisher is capable of sending
notifications for 'config false' nodes for the
relevant scope and subscription type.";
}
}
description
"Type for defining whether 'on-change' or
'periodic' notifications are supported for all data nodes,
'config false' data nodes, 'config true' data nodes, or
Wilton, et al. Expires 4 September 2025 [Page 90]
Internet-Draft YANG-Push Lite March 2025
no data nodes.
The bits config-changes or state-changes have no effect
when they are set for a datastore or for a set of nodes
that does not contain nodes with the indicated config
value. In those cases, the effect is the same as if no
support was declared. One example of this is indicating
support for state-changes for a candidate datastore that
has no effect.";
}
leaf periodic-notifications-supported {
type notification-support;
description
"Specifies whether the publisher is capable of
sending 'periodic' notifications for the selected
data nodes, including any subtrees that may exist
below them.";
reference
"RFC 8641: Subscription to YANG Notifications for
Datastore Updates, 'periodic' subscription concept";
}
choice update-period {
description
"Supported update period value or values for
'periodic' subscriptions.";
leaf minimum-update-period {
type uint32;
units "centiseconds";
description
"Indicates the minimal update period that is
supported for a 'periodic' subscription.
A subscription request to the selected data nodes with
a smaller period than what this leaf specifies is
likely to result in a 'period-unsupported' error.";
}
leaf-list supported-update-period {
type uint32;
units "centiseconds";
description
"Supported update period values for a 'periodic'
subscription.
A subscription request to the selected data nodes with a
period not included in the leaf-list will result in a
'period-unsupported' error.";
}
Wilton, et al. Expires 4 September 2025 [Page 91]
Internet-Draft YANG-Push Lite March 2025
}
leaf on-change-supported {
type notification-support;
description
"Specifies whether the publisher is capable of
sending 'on-change' notifications for the selected
data nodes and the subtree below them.";
}
}
}
grouping yp-lite-transport-capabilities {
description
"Capabilities related to transports supporting Yang Push Lite";
container transport {
description
"Specifies capabilities related to YANG-Push transports.";
list transport-capability {
key "transport-protocol";
description
"Indicates a list of capabilities related to notification
transport.";
leaf transport-protocol {
type identityref {
base ypl:transport;
}
description
"Indicates supported transport protocol for YANG-Push.";
}
leaf security-protocol {
type identityref {
base security-protocol;
}
description
"Indicates transport security protocol.";
}
leaf-list encoding-format {
type identityref {
base ypl:encoding;
}
description
"Indicates supported encoding formats.";
}
}
}
}
// YANG Push Lite Capabilities
Wilton, et al. Expires 4 September 2025 [Page 92]
Internet-Draft YANG-Push Lite March 2025
augment "/sysc:system-capabilities" {
description
"Adds system level capabilities for YANG Push Lite";
uses yp-lite-capabilities;
}
augment "/sysc:system-capabilities/yplc:datastore-telemetry" {
description
"Adds system level Yang Push Lite transport capabilities";
uses yp-lite-transport-capabilities;
}
augment "/sysc:system-capabilities/sysc:datastore-capabilities"
+ "/sysc:per-node-capabilities" {
description
"Add datastore and node-level capabilities";
uses yp-lite-capabilities;
}
}
<CODE ENDS>
Figure 21: YANG module ietf-yp-lite-capabilities
14. Security Considerations
With configured subscriptions, one or more publishers could be used
to overwhelm a receiver. To counter this, notification messages
SHOULD NOT be sent to any receiver that does not support this
specification. Receivers that do not want notification messages need
only terminate or refuse any transport sessions from the publisher.
When a receiver of a configured subscription gets a new
"subscription-started" message for a known subscription where it is
already consuming events, it may indicate that an attacker has done
something that has momentarily disrupted receiver connectivity. *TODO
- Do we still want this paragraph?*.
For dynamic subscriptions, implementations need to protect against
malicious or buggy subscribers that may send a large number of
"establish-subscription" requests and thereby use up system
resources. To cover this possibility, operators SHOULD monitor for
such cases and, if discovered, take remedial action to limit the
resources used, such as suspending or terminating a subset of the
subscriptions or, if the underlying transport is session based,
terminating the underlying transport session.
Wilton, et al. Expires 4 September 2025 [Page 93]
Internet-Draft YANG-Push Lite March 2025
Using DNS names for configured subscription's receiver "name" lookups
can cause situations where the name resolves differently than
expected on the publisher, so the recipient would be different than
expected.
14.1. Receiver Authorization
*TODO Relax when access control must be checked.*
*TODO Consider if this is the best place in the document, but this
text needs to be updated regardless.*
A receiver of subscription data MUST only be sent updates for which
it has proper authorization. A publisher MUST ensure that no
unauthorized data is included in push updates. To do so, it needs to
apply all corresponding checks applicable at the time of a specific
pushed update and, if necessary, silently remove any unauthorized
data from datastore subtrees. This enables YANG data that is pushed
based on subscriptions to be authorized in a way that is equivalent
to a regular data retrieval ("get") operation.
Each "push-update" and "push-change-update" MUST have access control
applied, as depicted in Figure 5. This includes validating that read
access is permitted for any new objects selected since the last
notification message was sent to a particular receiver. A publisher
MUST silently omit data nodes from the results that the client is not
authorized to see. To accomplish this, implementations SHOULD apply
the conceptual authorization model of [RFC8341], specifically
Section 3.2.4, extended to apply analogously to data nodes included
in notifications, not just <rpc-reply> messages sent in response to
<get> and <get-config> requests.
+-----------------+ +--------------------+
push-update or --> | datastore node | yes | add datastore node |
push-change-update | access allowed? | ---> | to update record |
+-----------------+ +--------------------+
Figure 22: Access Control for Push Updates
A publisher MUST allow for the possibility that a subscription's
selection filter references nonexistent data or data that a receiver
is not allowed to access. Such support permits a receiver the
ability to monitor the entire lifecycle of some datastore tree
without needing to explicitly enumerate every individual datastore
node. If, after access control has been applied, there are no
objects remaining in an update record, then the effect varies given
if the subscription is a periodic or on-change subscription. For a
periodic subscription, an empty "push-update" notification MUST be
Wilton, et al. Expires 4 September 2025 [Page 94]
Internet-Draft YANG-Push Lite March 2025
sent, so that clients do not get confused into thinking that an
update was lost. For an on-change subscription, a "push-update"
notification MUST NOT be sent, so that clients remain unaware of
changes made to nodes they don't have read-access for.
A publisher MAY choose to reject an "establish-subscription" request
that selects nonexistent data or data that a receiver is not allowed
to access. The error identity "unchanging-selection" SHOULD be
returned as the reason for the rejection. In addition, a publisher
MAY choose to terminate a dynamic subscription or suspend a
configured receiver when the authorization privileges of a receiver
change or the access controls for subscribed objects change. In that
case, the publisher SHOULD include the error identity "unchanging-
selection" as the reason when sending the "subscription-terminated"
or "subscription-suspended" notification, respectively. Such a
capability enables the publisher to avoid having to support
continuous and total filtering of a subscription's content for every
update record. It also reduces the possibility of leakage of access-
controlled objects.
If read access into previously accessible nodes has been lost due to
a receiver permissions change, this SHOULD be reported as a patch
"delete" operation for on-change subscriptions. If not capable of
handling such receiver permission changes with such a "delete",
publisher implementations MUST force dynamic subscription re-
establishment or configured subscription reinitialization so that
appropriate filtering is installed.
14.2. YANG Module Security Considerations
*TODO - Check that this section is still correct at WG LC, and
before/after IESG Evaluation, if the YANG data model changes at all*.
This section is modeled after the template described in Section 3.7.1
of [I-D.draft-ietf-netmod-rfc8407bis].
The "ietf-yp-lite" YANG module defines a data model that is designed
to be accessed via YANG-based management protocols, such as NETCONF
[RFC6241] and RESTCONF [RFC8040]. These protocols have to use a
secure transport layer (e.g., SSH [RFC4252], TLS [RFC8446], and QUIC
[RFC9000]) and have to use mutual authentication.
The Network Configuration Access Control Model (NACM) [RFC8341]
provides the means to restrict access for particular NETCONF or
RESTCONF users to a preconfigured subset of all available NETCONF or
RESTCONF protocol operations and content.
Wilton, et al. Expires 4 September 2025 [Page 95]
Internet-Draft YANG-Push Lite March 2025
There are a number of data nodes defined in this YANG module that are
writable/creatable/deletable (i.e., "config true", which is the
default). All writable data nodes are likely to be reasonably
sensitive or vulnerable in some network environments. Write
operations (e.g., edit-config) and delete operations to these data
nodes without proper protection or authentication can have a negative
effect on network operations. The following subtrees and data nodes
have particular sensitivities/vulnerabilities:
* There are no particularly sensitive writable data nodes.
Some of the readable data nodes in this YANG module may be considered
sensitive or vulnerable in some network environments. It is thus
important to control read access (e.g., via get, get-config, or
notification) to these data nodes. Specifically, the following
subtrees and data nodes have particular sensitivities/
vulnerabilities:
* There are no particularly sensitive readable data nodes.
Some of the RPC or action operations in this YANG module may be
considered sensitive or vulnerable in some network environments. It
is thus important to control access to these operations.
Specifically, the following operations have particular sensitivities/
vulnerabilities:
* kill-subscription - this RPC operation allows the caller to kill
any dynamic subscription, even those created via other users, or
other transport sessions.
*TODO - As per the template in [I-D.draft-ietf-netmod-rfc8407bis], we
would need to add text for groupings if we add any groupings from
elsewhere, or the modules define groupings that are expected to be
used by other modules.*
15. IANA Considerations
This document registers the following namespace URI in the "IETF XML
Registry" [RFC3688]:
URI: urn:ietf:params:xml:ns:yang:ietf-yp-lite
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
This document registers the following YANG module in the "YANG Module
Names" registry [RFC6020]:
Wilton, et al. Expires 4 September 2025 [Page 96]
Internet-Draft YANG-Push Lite March 2025
Name: ietf-yp-lite
Namespace: urn:ietf:params:xml:ns:yang:ietf-yp-lite
Prefix: ypl
Reference: RFC XXXX
Acknowledgments
This inital draft is early work is based on discussions with various
folk, particularly Thomas Graf, Holger Keller, Dan Voyer, Nils
Warnke, and Alex Huang Feng; but also wider conversations that
include: Benoit Claise, Pierre Francois, Paolo Lucente, Jean
Quilbeuf, among others.
Contributors
The following individuals have actively contributed to this draft and
the YANG Push Solution.
* Dan Voyer (TBD)
References
Normative References
[I-D.draft-netana-netconf-notif-envelope]
Feng, A. H., Francois, P., Graf, T., and B. Claise,
"Extensible YANG Model for YANG-Push Notifications", Work
in Progress, Internet-Draft, draft-netana-netconf-notif-
envelope-02, 28 January 2025,
<https://datatracker.ietf.org/doc/html/draft-netana-
netconf-notif-envelope-02>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/rfc/rfc2119>.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
DOI 10.17487/RFC2474, December 1998,
<https://www.rfc-editor.org/rfc/rfc2474>.
Wilton, et al. Expires 4 September 2025 [Page 97]
Internet-Draft YANG-Push Lite March 2025
[RFC5277] Chisholm, S. and H. Trevino, "NETCONF Event
Notifications", RFC 5277, DOI 10.17487/RFC5277, July 2008,
<https://www.rfc-editor.org/rfc/rfc5277>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/rfc/rfc6241>.
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC6991, July 2013,
<https://www.rfc-editor.org/rfc/rfc6991>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/rfc/rfc7950>.
[RFC7951] Lhotka, L., "JSON Encoding of Data Modeled with YANG",
RFC 7951, DOI 10.17487/RFC7951, August 2016,
<https://www.rfc-editor.org/rfc/rfc7951>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.
[RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
<https://www.rfc-editor.org/rfc/rfc8340>.
[RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC8341, March 2018,
<https://www.rfc-editor.org/rfc/rfc8341>.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/rfc/rfc8342>.
[RFC8525] Bierman, A., Bjorklund, M., Schoenwaelder, J., Watsen, K.,
and R. Wilton, "YANG Library", RFC 8525,
DOI 10.17487/RFC8525, March 2019,
<https://www.rfc-editor.org/rfc/rfc8525>.
[RFC8529] Berger, L., Hopps, C., Lindem, A., Bogdanovic, D., and X.
Liu, "YANG Data Model for Network Instances", RFC 8529,
DOI 10.17487/RFC8529, March 2019,
<https://www.rfc-editor.org/rfc/rfc8529>.
Wilton, et al. Expires 4 September 2025 [Page 98]
Internet-Draft YANG-Push Lite March 2025
[RFC8791] Bierman, A., Björklund, M., and K. Watsen, "YANG Data
Structure Extensions", RFC 8791, DOI 10.17487/RFC8791,
June 2020, <https://www.rfc-editor.org/rfc/rfc8791>.
[RFC9196] Lengyel, B., Clemm, A., and B. Claise, "YANG Modules
Describing Capabilities for Systems and Datastore Update
Notifications", RFC 9196, DOI 10.17487/RFC9196, February
2022, <https://www.rfc-editor.org/rfc/rfc9196>.
[RFC9254] Veillette, M., Ed., Petrov, I., Ed., Pelov, A., Bormann,
C., and M. Richardson, "Encoding of Data Modeled with YANG
in the Concise Binary Object Representation (CBOR)",
RFC 9254, DOI 10.17487/RFC9254, July 2022,
<https://www.rfc-editor.org/rfc/rfc9254>.
[RFC9485] Bormann, C. and T. Bray, "I-Regexp: An Interoperable
Regular Expression Format", RFC 9485,
DOI 10.17487/RFC9485, October 2023,
<https://www.rfc-editor.org/rfc/rfc9485>.
[RFC9595] Veillette, M., Ed., Pelov, A., Ed., Petrov, I., Ed.,
Bormann, C., and M. Richardson, "YANG Schema Item
iDentifier (YANG SID)", RFC 9595, DOI 10.17487/RFC9595,
July 2024, <https://www.rfc-editor.org/rfc/rfc9595>.
Informative References
[Consistency]
Wikipedia, "Consistency (database systems)",
<https://en.wikipedia.org/wiki/
Consistency_(database_systems)>.
[EventualConsistency]
Rouse, M., "Eventual Consistency",
<https://www.techopedia.com/definition/29165/eventual-
consistency>.
[gNMI] OpenConfig, "gRPC Network Management Interface (gNMI)",
<https://github.com/openconfig/reference/blob/master/rpc/
gnmi/gnmi-specification.md>.
[I-D.draft-ietf-netconf-distributed-notif]
Zhou, T., Zheng, G., Voit, E., Graf, T., and P. Francois,
"Subscription to Distributed Notifications", Work in
Progress, Internet-Draft, draft-ietf-netconf-distributed-
notif-13, 1 March 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-netconf-
distributed-notif-13>.
Wilton, et al. Expires 4 September 2025 [Page 99]
Internet-Draft YANG-Push Lite March 2025
[I-D.draft-ietf-netconf-https-notif]
Jethanandani, M. and K. Watsen, "An HTTPS-based Transport
for YANG Notifications", Work in Progress, Internet-Draft,
draft-ietf-netconf-https-notif-15, 1 February 2024,
<https://datatracker.ietf.org/doc/html/draft-ietf-netconf-
https-notif-15>.
[I-D.draft-ietf-netconf-udp-notif]
Zheng, G., Zhou, T., Graf, T., Francois, P., Feng, A. H.,
and P. Lucente, "UDP-based Transport for Configured
Subscriptions", Work in Progress, Internet-Draft, draft-
ietf-netconf-udp-notif-20, 3 March 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-netconf-
udp-notif-20>.
[I-D.draft-ietf-netmod-rfc8407bis]
Bierman, A., Boucadair, M., and Q. Wu, "Guidelines for
Authors and Reviewers of Documents Containing YANG Data
Models", Work in Progress, Internet-Draft, draft-ietf-
netmod-rfc8407bis-22, 14 January 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-netmod-
rfc8407bis-22>.
[I-D.draft-netana-netconf-yp-transport-capabilities]
Wu, Q., Ma, Q., Feng, A. H., and T. Graf, "YANG
Notification Transport Capabilities", Work in Progress,
Internet-Draft, draft-netana-netconf-yp-transport-
capabilities-01, 17 January 2025,
<https://datatracker.ietf.org/doc/html/draft-netana-
netconf-yp-transport-capabilities-01>.
[I-D.ietf-netconf-distributed-notif]
Zhou, T., Zheng, G., Voit, E., Graf, T., and P. Francois,
"Subscription to Distributed Notifications", Work in
Progress, Internet-Draft, draft-ietf-netconf-distributed-
notif-13, 1 March 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-netconf-
distributed-notif-13>.
[I-D.ietf-nmop-network-anomaly-architecture]
Graf, T., Du, W., and P. Francois, "An Architecture for a
Network Anomaly Detection Framework", Work in Progress,
Internet-Draft, draft-ietf-nmop-network-anomaly-
architecture-01, 20 October 2024,
<https://datatracker.ietf.org/doc/html/draft-ietf-nmop-
network-anomaly-architecture-01>.
Wilton, et al. Expires 4 September 2025 [Page 100]
Internet-Draft YANG-Push Lite March 2025
[I-D.ietf-nmop-yang-message-broker-integration]
Graf, T. and A. Elhassany, "An Architecture for YANG-Push
to Message Broker Integration", Work in Progress,
Internet-Draft, draft-ietf-nmop-yang-message-broker-
integration-07, 3 March 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-nmop-
yang-message-broker-integration-07>.
[I-D.netana-netconf-notif-envelope]
Feng, A. H., Francois, P., Graf, T., and B. Claise,
"Extensible YANG Model for YANG-Push Notifications", Work
in Progress, Internet-Draft, draft-netana-netconf-notif-
envelope-02, 28 January 2025,
<https://datatracker.ietf.org/doc/html/draft-netana-
netconf-notif-envelope-02>.
[I-D.tgraf-netconf-notif-sequencing]
Graf, T., Quilbeuf, J., and A. H. Feng, "Support of
Hostname and Sequencing in YANG Notifications", Work in
Progress, Internet-Draft, draft-tgraf-netconf-notif-
sequencing-06, 29 June 2024,
<https://datatracker.ietf.org/doc/html/draft-tgraf-
netconf-notif-sequencing-06>.
[I-D.tgraf-netconf-yang-push-observation-time]
Graf, T., Claise, B., and A. H. Feng, "Support of
Observation Timestamp in YANG-Push Notifications", Work in
Progress, Internet-Draft, draft-tgraf-netconf-yang-push-
observation-time-03, 14 December 2024,
<https://datatracker.ietf.org/doc/html/draft-tgraf-
netconf-yang-push-observation-time-03>.
[Kafka] Apache.org, "Apache Kafka", <https://kafka.apache.org/>.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
DOI 10.17487/RFC3411, December 2002,
<https://www.rfc-editor.org/rfc/rfc3411>.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/rfc/rfc3688>.
[RFC4252] Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH)
Authentication Protocol", RFC 4252, DOI 10.17487/RFC4252,
January 2006, <https://www.rfc-editor.org/rfc/rfc4252>.
Wilton, et al. Expires 4 September 2025 [Page 101]
Internet-Draft YANG-Push Lite March 2025
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<https://www.rfc-editor.org/rfc/rfc6020>.
[RFC7049] Bormann, C. and P. Hoffman, "Concise Binary Object
Representation (CBOR)", RFC 7049, DOI 10.17487/RFC7049,
October 2013, <https://www.rfc-editor.org/rfc/rfc7049>.
[RFC7540] Belshe, M., Peon, R., and M. Thomson, Ed., "Hypertext
Transfer Protocol Version 2 (HTTP/2)", RFC 7540,
DOI 10.17487/RFC7540, May 2015,
<https://www.rfc-editor.org/rfc/rfc7540>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/rfc/rfc8040>.
[RFC8071] Watsen, K., "NETCONF Call Home and RESTCONF Call Home",
RFC 8071, DOI 10.17487/RFC8071, February 2017,
<https://www.rfc-editor.org/rfc/rfc8071>.
[RFC8072] Bierman, A., Bjorklund, M., and K. Watsen, "YANG Patch
Media Type", RFC 8072, DOI 10.17487/RFC8072, February
2017, <https://www.rfc-editor.org/rfc/rfc8072>.
[RFC8259] Bray, T., Ed., "The JavaScript Object Notation (JSON) Data
Interchange Format", STD 90, RFC 8259,
DOI 10.17487/RFC8259, December 2017,
<https://www.rfc-editor.org/rfc/rfc8259>.
[RFC8343] Bjorklund, M., "A YANG Data Model for Interface
Management", RFC 8343, DOI 10.17487/RFC8343, March 2018,
<https://www.rfc-editor.org/rfc/rfc8343>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/rfc/rfc8446>.
[RFC8639] Voit, E., Clemm, A., Gonzalez Prieto, A., Nilsen-Nygaard,
E., and A. Tripathy, "Subscription to YANG Notifications",
RFC 8639, DOI 10.17487/RFC8639, September 2019,
<https://www.rfc-editor.org/rfc/rfc8639>.
Wilton, et al. Expires 4 September 2025 [Page 102]
Internet-Draft YANG-Push Lite March 2025
[RFC8640] Voit, E., Clemm, A., Gonzalez Prieto, A., Nilsen-Nygaard,
E., and A. Tripathy, "Dynamic Subscription to YANG Events
and Datastores over NETCONF", RFC 8640,
DOI 10.17487/RFC8640, September 2019,
<https://www.rfc-editor.org/rfc/rfc8640>.
[RFC8641] Clemm, A. and E. Voit, "Subscription to YANG Notifications
for Datastore Updates", RFC 8641, DOI 10.17487/RFC8641,
September 2019, <https://www.rfc-editor.org/rfc/rfc8641>.
[RFC9000] Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
Multiplexed and Secure Transport", RFC 9000,
DOI 10.17487/RFC9000, May 2021,
<https://www.rfc-editor.org/rfc/rfc9000>.
[XPATH] W3C, "XML Path Language (XPath) Version 1.0",
<https://www.w3.org/TR/1999/REC-xpath-19991116/>.
Appendix A. Functional changes between YANG Push Lite and YANG Push
This non-normative section highlights the significant functional
changes where the YANG Push Lite implementation differs from YANG
Push. However, the main body of this document, from Section 4
onwards, provides the normative definition of the YANG Push Lite
specification, except for any text or sections that explicitly
indicate that they are informative rather being normative.
_Note to reviewers: If you notice mistakes in this section during
development of the document and solution then please point them out
to the authors and the working group._ *(RFC editor, please remove
this paragraph prior to publication)*
A.1. Removed Functionality
This section lists functionality specified in [RFC8639] and YANG Push
which is not specified in YANG Push Lite.
* Negotiation and hints of failed subscriptions.
* The RPC to modify an existing dynamic subscription, instead the
subscription must be terminated and re-established.
* The ability to suspend and resume a dynamic subscription. Instead
a dynamic subscription is terminated if the device cannot reliably
fulfill the subscription or a receiver is too slow causing the
subscription to be back pressured.
Wilton, et al. Expires 4 September 2025 [Page 103]
Internet-Draft YANG-Push Lite March 2025
* Specifying a subscription stop time, and the corresponding
subscription-completed notification have been removed.
* Replaying of buffered event records are not supported. The
nearest equivalent is requesting a sync-on-start replay when the
subscription transport session comes up which will reply the
current state.
* QoS weighting and dependency between subscriptions has been
removed due to the complexity of implementation.
* Support for reporting subscription error hints has been removed.
The device SHOULD reject subscriptions that are likely to overload
the device, but more onus is placed on the operator configuring
the subscriptions or setting up the dynamic subscriptions to
ensure that subscriptions are reasonable, as they would be
expected to do for any other configuration.
* The "subscription-state-notif" extension has been removed.
* The YANG Patch format [RFC8072] is no longer used for on-change
subscriptions.
A.2. Changed Functionality
This section documents behavior that exists in both YANG Push and
YANG Push Lite, but the behavior differs between the two:
* All YANG Push Lite notifications messages use
[I-D.draft-netana-netconf-notif-envelope] rather than [RFC5277]
used by YANG Push.
* Changes to handling receivers:
- Receivers are always configured separately from the
subscription and are referenced.
- Transport and Encoding parameters are configured as part of a
receiver definition, and are used by all subscriptions directed
towards a given receiver.
- If a subscription uses multiple receivers then:
o Update messages and lifecycle notifications are sent to all
receivers (to preserve sequence numbers)
o all receivers must be configured with the same encoding
Wilton, et al. Expires 4 September 2025 [Page 104]
Internet-Draft YANG-Push Lite March 2025
* Periodic and on-change message uses a common _update_ notification
message format, allowing for the messages to be processed by
clients in a similar fashion and to support combined periodic and
on-change subscriptions.
* On-change dampening:
- Client configurable on-change dampening has been removed.
- However, YANG Push Lite allows a publisher to limit the rate at
which a data node is sampled for on-change notifications. See
Section 7.5.1 for further details.
* Dynamic subscriptions are no longer mandatory to implement, either
or both of Configured and Dynamic Subscriptions may be implemented
in YANG Push Lite.
* The solution focuses solely on datastore subscriptions that each
have their own event stream. Filters cannot be applied to the
event stream, only to the set of datastore data nodes that are
monitored by the subscription.
* The lifecycle events of when a subscription-started or
subscription-terminated may be sent differs from RFC 8639/RFC
8649:
- Subscription-started notifications are also sent for dynamic
subscriptions.
* Some of the requirements on transport have been relaxed.
* The encoding identities have been extended with CBOR encodings,
and the "encoding-" prefix has been removed (so that there is a
better on the wire representation).
* YANG Push Lite allows for a publisher to provide an eventually
consistent distributed view of the operational datastore, rather
than a fully consistent datastore where on-change updates are sent
as logic diffs to that datastore.
A.3. Added Functionality
* Device capabilities are reported via XXX and additional models
that augment that data model.
* A new _update_ message:
- Covers both on-change and periodic events.
Wilton, et al. Expires 4 September 2025 [Page 105]
Internet-Draft YANG-Push Lite March 2025
- Allows multiple updates to be sent in a single message (e.g.,
for on-change).
- Allows for a common path prefix to be specified, with any paths
and encoded YANG data to be encoded relative to the common path
prefix.
* A _collection-complete_ notification, and associated
configuration, has been defined to inform collectors when a
subscription's periodic collection cycle is complete.
* TODO - More operational data on the subscription load and
performance.
* All YANG Push Lite configuration is under a new _datastore-
telemetry_ presence container
Appendix B. Subscription Errors (from RFC 8641)
B.1. RPC Failures
Rejection of an RPC for any reason is indicated via an RPC error
response from the publisher. Valid RPC errors returned include both
(1) existing transport-layer RPC error codes, such as those seen with
NETCONF in [RFC6241] and (2) subscription-specific errors, such as
those defined in the YANG data model. As a result, how subscription
errors are encoded in an RPC error response is transport dependent.
References to specific identities in the ietf-subscribed-
notifications YANG module [RFC8639] or the ietf-yang-push YANG module
may be returned as part of the error responses resulting from failed
attempts at datastore subscription. For errors defined as part of
the ietf-subscribed-notifications YANG module, please refer to
[RFC8639]. The errors defined in this document, grouped per RPC, are
as follows:
establish-subscription modify-subscription
--------------------------- ---------------------
cant-exclude period-unsupported
datastore-not-subscribable update-too-big
on-change-unsupported sync-too-big
on-change-sync-unsupported unchanging-selection
period-unsupported
update-too-big resync-subscription
sync-too-big ----------------------------
unchanging-selection no-such-subscription-resync
sync-too-big
Wilton, et al. Expires 4 September 2025 [Page 106]
Internet-Draft YANG-Push Lite March 2025
There is one final set of transport-independent RPC error elements
included in the YANG data model. These are the four yang-data
structures for failed datastore subscriptions:
1. yang-data "establish-subscription-error-datastore": This MUST be
returned if information identifying the reason for an RPC error
has not been placed elsewhere in the transport portion of a
failed "establish-subscription" RPC response. This MUST be sent
if hints are included.
2. yang-data "modify-subscription-error-datastore": This MUST be
returned if information identifying the reason for an RPC error
has not been placed elsewhere in the transport portion of a
failed "modify-subscription" RPC response. This MUST be sent if
hints are included.
3. yang-data "sn:delete-subscription-error": This MUST be returned
if information identifying the reason for an RPC error has not
been placed elsewhere in the transport portion of a failed
"delete-subscription" or "kill-subscription" RPC response.
4. yang-data "resync-subscription-error": This MUST be returned if
information identifying the reason for an RPC error has not been
placed elsewhere in the transport portion of a failed "resync-
subscription" RPC response.
B.2. Failure Notifications
A subscription may be unexpectedly terminated or suspended
independently of any RPC or configuration operation. In such cases,
indications of such a failure MUST be provided. To accomplish this,
a number of errors can be returned as part of the corresponding
subscription state change notification. For this purpose, the
following error identities are introduced in this document, in
addition to those that were already defined in [RFC8639]:
subscription-terminated subscription-suspended
--------------------------- ----------------------
datastore-not-subscribable period-unsupported
unchanging-selection update-too-big
synchronization-size
Appendix C. Examples
Notes on examples:
Wilton, et al. Expires 4 September 2025 [Page 107]
Internet-Draft YANG-Push Lite March 2025
* To allow for programmatic validation, most notification examples
in this section exclude the mandatory notification envelope and
associated metadata defined in
[I-D.netana-netconf-notif-envelope]. Only the full notification
example in Section 7.1 includes the notification header.
* These examples have been given using a JSON encoding of the
regular YANG-Push notification format, i.e., encoded using
[RFC5277], but it is anticipated that these notifications could be
defined to exclusively use the new format proposed by
[I-D.netana-netconf-notif-envelope].
* Some additional meta data fields, e.g., like those defined in
[I-D.tgraf-netconf-notif-sequencing] would also likely be
included, but have also been excluded to allow for slightly more
concise examples.
* The examples include the
[I-D.tgraf-netconf-yang-push-observation-time] field for the
existing YANG-Push Notification format, and the proposed
equivalent "observation-time" leaf for the new update notification
format.
* All these examples are created by hand, may contain errors, and
may not parse correctly.
C.1. Example of update message using the new style update message
The subscription was made on "Cisco-IOS-XR-pfi-im-cmd-
oper:interfaces", but for efficiency reasons, the device has split
the subscription into separate child subscriptions for the different
data providers, and makes use of the new message format.
Hence, this first periodic message is being published for the "Cisco-
IOS-XR-pfi-im-cmd-oper:interfaces/interface-summary" container, but
it is encoded rooted relative to the schema for "Cisco-IOS-XR-pfi-im-
cmd-oper:interfaces".
Wilton, et al. Expires 4 September 2025 [Page 108]
Internet-Draft YANG-Push Lite March 2025
{
"ietf-notification:notification": {
"eventTime": "2024-09-27T14:16:27.773Z",
"ietf-yp-ext:update": {
"id": 1,
"subscription-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:interfaces",
"target-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:"
"interfaces/interface-summary",
"snapshot-type": "periodic"
"observation-time": "2024-09-27T14:16:27.773Z",
"datastore-snapshot": {
"interface-summary" : {
"interface-type": [
{
"interface-type-name": "IFT_GETHERNET",
"interface-type-description": "GigabitEthernet",
"interface-counts": {
"interface-count": 5,
"up-interface-count": 2,
"down-interface-count": 0,
"admin-down-interface-count": 3
}
}
],
"interface-counts": {
"interface-count": 8,
"up-interface-count": 5,
"down-interface-count": 0,
"admin-down-interface-count": 3
}
}
}
}
}
}
The second periodic message is being published for the "Cisco-IOS-XR-
pfi-im-cmd-oper:interfaces/interfaces/interface" list, but again, it
is encoded rooted relative to the schema for "Cisco-IOS-XR-pfi-im-
cmd-oper:interfaces". This message has a separate observation time
that represents the more accurate time that this periodic date was
read.
Wilton, et al. Expires 4 September 2025 [Page 109]
Internet-Draft YANG-Push Lite March 2025
{
"ietf-notification:notification": {
"eventTime": "2024-09-27T14:16:27.973Z",
"ietf-yp-ext:update": {
"id": 1,
"subscription-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:interfaces",
"target-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:
interfaces/interfaces/interface[]",
"snapshot-type": "periodic"
"observation-time": "2024-09-27T14:16:27.973Z",
"datastore-snapshot": {
"interfaces": {
"interface": [
{
"interface-name": "GigabitEthernet0/0/0/0",
"interface": "GigabitEthernet0/0/0/0",
"state": "im-state-admin-down",
"line-state": "im-state-admin-down"
},
{
"interface-name": "GigabitEthernet0/0/0/4",
"interface": "GigabitEthernet0/0/0/4",
"state": "im-state-admin-down",
"line-state": "im-state-admin-down"
},
]
}
}
}
}
}
Each child subscription would use the same period and anchor time as
the configured subscription, possibly with a little bit of initial
jitter to avoid all daemons attempting to publish the data at exactly
the same time.
C.2. Example of an on-change-update notification using the new style
update message
If the subscription is for on-change notifications, or periodic-and-
on-change-notifications, then, if the interface state changed
(specifically if the 'state' leaf of the interface changed state),
and if the device was capable of generating on-change notifications,
then you may see the following message. A few points of notes here:
Wilton, et al. Expires 4 September 2025 [Page 110]
Internet-Draft YANG-Push Lite March 2025
* The on-change notification contains *all* of the state at the
"target-path"
- Not present in the below example, but if the notification
excluded some state under an interfaces list entry (e.g., the
line-state leaf) then this would logically represent the
implicit deletion of that field under the given list entry.
- In this example it is restricted to a single interface. It
could also publish an on-change notification for all
interfaces, by indicating a target-path without any keys
specified. TODO - Can it represent notifications for a subset
of interfaces?
* The schema of the change message is exactly the same as for the
equivalent periodic message. It doesn't use the YANG Patch format
[RFC8072] for on-change messages.
* The "observation time" leaf represents when the system first
observed the on-change event occurring.
* The on-change event doesn't differentiate the type of change to
operational state. The on-change-update snapshot type is used to
indicate the creation of a new entry or some update to some
existing state. Basically, the message can be thought of as the
state existing with some current value.
Wilton, et al. Expires 4 September 2025 [Page 111]
Internet-Draft YANG-Push Lite March 2025
{
"ietf-notification:notification": {
"eventTime": "2024-09-27T14:16:30.973Z",
"ietf-yp-ext:update": {
"id": 1,
"subscription-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:interfaces",
"target-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:interfaces/interfaces/
interface[interface=GigabitEthernet0/0/0/0]",
"snapshot-type": "on-change-update"
"observation-time": "2024-09-27T14:16:30.973Z",
"datastore-snapshot": {
"interfaces": {
"interface": [
{
"interface-name": "GigabitEthernet0/0/0/0",
"interface": "GigabitEthernet0/0/0/0",
"state": "im-state-up",
"line-state": "im-state-up"
}
]
}
}
}
}
}
C.3. Example of an on-change-delete notification using the new style
update message
If the interface was deleted, and if the system was capable of
reporting on-change events for the delete event, then an on-change
delete message would be encoded as per the following message. Of
note:
* The on-change-delete snapshot type doesn't include a "datastore-
snapshot", instead it represents a delete of the list entry at the
path identified by the target-path, which is similar to a YANG
Patch delete notification.
Wilton, et al. Expires 4 September 2025 [Page 112]
Internet-Draft YANG-Push Lite March 2025
{
"ietf-notification:notification": {
"eventTime": "2024-09-27T14:16:40.973Z",
"ietf-yp-ext:update": {
"id": 1,
"subscription-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:interfaces",
"target-path":
"Cisco-IOS-XR-pfi-im-cmd-oper:interfaces/interfaces/
interface[interface=GigabitEthernet0/0/0/0]",
"snapshot-type": "on-change-delete"
"observation-time": "2024-09-27T14:16:40.973Z",
}
}
}
C.4. Subscription RPC examples (from RFC 8641)
YANG-Push subscriptions are established, modified, and deleted using
RPCs augmented from [RFC8639].
C.4.1. "establish-subscription" RPC
The subscriber sends an "establish-subscription" RPC with the
parameters listed in Section 3.1. An example might look like:
<netconf:rpc message-id="101"
xmlns:netconf="urn:ietf:params:xml:ns:netconf:base:1.0">
<establish-subscription
xmlns="urn:ietf:params:xml:ns:yang:ietf-subscribed-notifications"
xmlns:yp="urn:ietf:params:xml:ns:yang:ietf-yang-push">
<yp:datastore
xmlns:ds="urn:ietf:params:xml:ns:yang:ietf-datastores">
ds:operational
</yp:datastore>
<yp:datastore-xpath-filter
xmlns:ex="https://example.com/sample-data/1.0">
/ex:foo
</yp:datastore-xpath-filter>
<yp:periodic>
<yp:period>500</yp:period>
</yp:periodic>
</establish-subscription>
</netconf:rpc>
Figure 10: "establish-subscription" RPC
Wilton, et al. Expires 4 September 2025 [Page 113]
Internet-Draft YANG-Push Lite March 2025
A positive response includes the "id" of the accepted subscription.
In that case, a publisher may respond as follows:
<rpc-reply message-id="101"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<id
xmlns="urn:ietf:params:xml:ns:yang:ietf-subscribed-notifications">
52
</id>
</rpc-reply>
Figure 11: "establish-subscription" Positive RPC Response
A subscription can be rejected for multiple reasons, including the
lack of authorization to establish a subscription, no capacity to
serve the subscription at the publisher, or the inability of the
publisher to select datastore content at the requested cadence.
If a request is rejected because the publisher is not able to serve
it, the publisher SHOULD include in the returned error hints that
help a subscriber understand what subscription parameters might have
been accepted for the request. These hints would be included in the
yang-data structure "establish-subscription-error-datastore".
However, even with these hints, there are no guarantees that
subsequent requests will in fact be accepted.
The specific parameters to be returned as part of the RPC error
response depend on the specific transport that is used to manage the
subscription. For NETCONF, those parameters are defined in
[RFC8640]. For example, for the following NETCONF request:
Wilton, et al. Expires 4 September 2025 [Page 114]
Internet-Draft YANG-Push Lite March 2025
<rpc message-id="101"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<establish-subscription
xmlns=
"urn:ietf:params:xml:ns:yang:ietf-subscribed-notifications"
xmlns:yp="urn:ietf:params:xml:ns:yang:ietf-yang-push">
<yp:datastore
xmlns:ds="urn:ietf:params:xml:ns:yang:ietf-datastores">
ds:operational
</yp:datastore>
<yp:datastore-xpath-filter
xmlns:ex="https://example.com/sample-data/1.0">
/ex:foo
</yp:datastore-xpath-filter>
<yp:on-change>
</yp:on-change>
</establish-subscription>
</rpc>
Figure 12: "establish-subscription" Request: Example 2
A publisher that cannot serve on-change updates but can serve
periodic updates might return the following NETCONF response:
<rpc-reply message-id="101"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"
xmlns:yp="urn:ietf:params:xml:ns:yang:ietf-subscribed-notifications">
<rpc-error>
<error-type>application</error-type>
<error-tag>operation-failed</error-tag>
<error-severity>error</error-severity>
<error-path>/yp:periodic/yp:period</error-path>
<error-info>
<yp:establish-subscription-error-datastore>
<yp:reason>yp:on-change-unsupported</yp:reason>
</yp:establish-subscription-error-datastore>
</error-info>
</rpc-error>
</rpc-reply>
Figure 13: "establish-subscription" Error Response: Example 2
Wilton, et al. Expires 4 September 2025 [Page 115]
Internet-Draft YANG-Push Lite March 2025
C.4.2. "delete-subscription" RPC
To stop receiving updates from a subscription and effectively delete
a subscription that had previously been established using an
"establish-subscription" RPC, a subscriber can send a "delete-
subscription" RPC, which takes as its only input the subscription's
"id". This RPC is unmodified from [RFC8639].
C.4.3. "resync-subscription" RPC
This RPC is supported only for on-change subscriptions previously
established using an "establish-subscription" RPC. For example:
<rpc message-id="103"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<resync-subscription
xmlns="urn:ietf:params:xml:ns:yang:ietf-yang-push">
<id>1011</id>
</resync-subscription>
</rpc>
Figure 15: "resync-subscription"
On receipt, a publisher must either (1) accept the request and
quickly follow with a "push-update" or (2) send an appropriate error
in an RPC error response. In its error response, the publisher MAY
include, in the yang-data structure "resync-subscription-error",
supplemental information about the reasons for the error.
Appendix D. Summary of Open Issues & Potential Enhancements
This temporary section lists open issues and enhancements that
require further discussion by the authors, or the WG. Once adopted,
it is anticipated that tracking the open issues would move to github.
The issues are ordered/grouped by the sections in the current
document. I.e., to make it easier to review/update sections of the
document.
D.1. Issues related to general IETF process:
1. If this work progresses we will need simple bis versions of the
transports document so that they augment into the new data model
paths. Drafts that would need to be updated as documented in
Section 3.4.
Wilton, et al. Expires 4 September 2025 [Page 116]
Internet-Draft YANG-Push Lite March 2025
2. Do we need to fold in any text from RFC 8640? and RESTCONF.
I.e., there was this text in the one of the previous docs:
Bindings for subscribed event record delivery for NETCONF and
RESTCONF are defined in [RFC8640] and *RESTCONF-Notif*,
respectively.
* Rob: If text is needed for NETCONF and/or RESTCONF then I
suspect that it would be better added to this document than to
require small separate documents (as was done before).
D.2. Issue related to Terminology/Definitions:
1. Should we use the object terminology? This may be better than
data node subtree, or the equivalent, and could be better than
introducing _bags_?
* Holger: should try and use same terminology as existing YANG
Push RFCs.
* Rob: This issue can be a place holder, to go through and
check/update the terminology used, and see if any of the
referenced terminology isn't neeed in YP Lite.
D.3. Issues related to YANG Push Lite Overview.
None currently.
D.4. Issues related to Subscription Paths and Selection Filters
1. This draft introduces a new simple yang path (ypath) format that
is like a JSON instance data path, that all implementations MUST
support.
* Vendors already support a simple JSON like path (e.g., using
module-names rather than XML namespaces).
* *Open questions (for further discussion):*
- Do we support filtering on non-keys, e.g., this example
from Thomas (but which filters on a non-key):
/if:interfaces-state/if:interface[if:type='ianaift:ethernet
Csmacd']/if:statistics
- Do we support simple regex filtering on the keys (and if
so, how would that be expressed, would it be compatible
with JSON Path)
Wilton, et al. Expires 4 September 2025 [Page 117]
Internet-Draft YANG-Push Lite March 2025
- Do we need any more complex filtering (e.g., Holger's
example of only getting entries from a list if they are in
a particular state.), or do we always use subtree filters
for that?
* *Authors: I provides some suggested text in Section 6.1, but I
expect further discussion may be needed. (E.g., how multiple
keys should be expressed)*
2. The draft retains OPTIONAL subtree filtering (under a feature
statement):
* What is the schema associated with this subtree (compared to a
simple path), and how is this expressed?
* Does the subtree filter get put into the subscription-started
message?
3. xpath filtering - conslusion is that we should keep this in a
draft as a MAY (under a feature statement).
* Do we allow implementations to support a subset of xpath
syntax, or should they support all of xpath.
* *Proposal: From an IETF draft perspective, don't say anything,
i.e., it just indicates support for XPath filtering without
explicitly saying whether or not it must all be supported*
D.5. Issues related to Datastore Event Streams
D.5.1. Further refinements on how a subscription can be decomposed
internally into child subscriptions with the data returned for
each child subscription:
1. Handling lists with separate producers of list entries.
* If a subscription is decomposed, then should the subscription
started message for the configured subscription indicate how
that subscription has been decomposed?
* Do we need to add an optional replay-end (i.e., after a sync-
on-start) or collection-end (i.e., after every collection)
notification so that clients can determine when data can be
implicitly deleted.
- Rob: I think that we should add the latter, but make it a
subscription config option to turn it on.
Wilton, et al. Expires 4 September 2025 [Page 118]
Internet-Draft YANG-Push Lite March 2025
- Holger, strong support for adding this, often requested.
- Thomas, yes we need this, but need to determine whether
this is per subscription or per publisher.
D.5.2. Questions/comments on the notification message format:
1. We allow multiple updates within a single message (primary use
case is for the on-change case). What about the timestamp, which
is still just once per message (like gNMI)? Should message
bundling be optional/configurable to implement (if they all use a
single shared timestamp)?
* on-change deletes are implicit by an update that replaces an
existing entry with an empty data node (e.g., "{}" in JSON)
- An alternative choice here could be an explicit delete
flag, we need to decide which would be simpler/better.
* The update message also currently includes a path-prefix to
allow (like gNMI) so that they don't necessarily need to be
encoded from root, specifically, I think that this makes on-
change messages nicer, since the on-change is rooted to the
thing that is changing rather than the root of the tree. We
need to define semantics of how this works, e.g., this should
probably be controlled via configuration.
- Ideally, the path prefix would be exactly the same as the
YPath format that is being specified for configuration.
* Do we keep the "incomplete" update flag? Otherwise how would
a publisher indicate that a message was not complete.
- Thomas: We should keep this.
* _Further discussion of this issue is needed_
D.6. Issues related to Receivers, Transports, & Encodings
D.6.1. Constraints on supporting multiple receivers:
1. Encoding is set per receiver, but do we need to support a
subscription supporting more than one receiver with different
encodings?
* Rob: Note, it is always possible for a client to setup
different subscriptions.
Wilton, et al. Expires 4 September 2025 [Page 119]
Internet-Draft YANG-Push Lite March 2025
* Thomas: This could be useful, e.g., when migrating from one
encoding to another, particularly, if it reduced the load on
the publisher (compared to creating a new separate
subscription).
* Rob: I don't think that we would end up optimizing for this
case (but would need to check).
* Also need to check with Nokia/Huawei would support this.
* *Current status: Left open for further discussion.*
* Note: This may also have a minor impact on the data model.
2. Lifecycle message should be sent per subscription, not per
receiver (i.e., every receiver gets the same message (ignoring
transport headers)):
* Consensus agreed this is the right thing to do.
* *Action on Rob to check/update the draft.*
* Notes:
- Every receiver gets the same sequence number in the
message.
- subscription-created notification could perhaps have an
enum giving a reason for the notification (e.g., new
subscription, receiver added).
3. Do we need a per-receiver notification to indicate to a specific
receiver that it has been disconnected?
* This would seem to only apply to configured subscriptions
(since dynamic cannot have more than one receiver).
* If the transport session went down, then the publisher would
be expected to reconnect anyway.
* So, the specific use case is likely to be unconfiguring a
receiver for a subscription that has multiple receivers.
* *Currently parked for further discussion.*
Wilton, et al. Expires 4 September 2025 [Page 120]
Internet-Draft YANG-Push Lite March 2025
D.6.2. Issues related to Transports:
1. Section 8.2 lists quite a lot of rules on what are valid
transports and what negotation/etc is required. I think we need
to check whether we can weaken some of these (although it is
possible that these were imposed during a transport directorate
review).
* *Rob: Authors, I've updated the transport section,
Section 8.2, please can you re-review.*
2. James: We also need to add some text into security section.
* Rob: Is this transport specific, or related to application
layer authorization?
3. What is the rules/restrictions for subscription receiver
instances vs transport sessions? E.g., is this entirely down to
the transport to define.
D.7. Issues related to Setting up & Managing Subscriptions
D.7.1. Issues related to the configuration model:
Note some of these apply or impact dynamic subscriptions as well.
1. YP Lite is somewhat different (separate namespace, separate
receivers, no event filters, some config has moved to a separate
receivers list.) See the data model and Appendix A.
2. We should allow devices to limit which datastores subscriptions
can be made against (e.g., not candidate or factory-default as
some obvious examples). Should these be advertised in the
capabilities?
3. (James) Should we even document the configuration data model in
this document at all, or should it be in a separate document?
4. Some other changes/proposed changes:
* I've removed some of the YANG features for 'small' one/two
changes in configuration. I propose that we don't need
features for these at all (e.g., DSCP settings), or in other
cases we can use operational capabilities, or rely on
deviations.
- I've renamed the encodings (e.g., from "encode-json" to
just "json")
Wilton, et al. Expires 4 September 2025 [Page 121]
Internet-Draft YANG-Push Lite March 2025
- Maybe further simplification of the receivers list under
the subscription. E.g., do we need stats per subscription
per receiver, or just per subscription? Do want stats
across all subscriptions to a given receiver?
o Holger: Stats per subscription should be sufficient. No
need for per subscription/pre-receiver stats (which
would allow the data model to be simplified a little
bit).
- Subscription-ids are currently numeric values with the
space split between configured and dynamic subscriptions,
but I think that the config model would be cleaner if we
used names for the configured subscriptions (and we could
reserve a prefix "dyn-" for dynamic subscriptions).
o Holger, Rob: Strong preference to names.
o Thomas, keep ids, but rename 'purpose' to name. Also
give receivers an ids and be keyed this.
D.7.2. Issues related to dynamic subscriptions:
1. In YP Lite, dynamic subscriptions are designed to be closer to
configured subscriptions and share more of the data model and
lifecycle handling. I.e., the primary differentiator is meant to
be how they are instantiated.
* James, Rob: More alignment is better.
2. Do we want to change how RPC errors are reported? E.g., change
the RPC ok response to indicate whether the subscription was
successfully created or not, or included extra error information.
Note NETCONF and RESTCONF already define how errors are encoded
in XML and JSON (for RESTCONF only).
3. Do we need to allow a dynamic subscription to be modified? If we
do, then it would be better to change the establish-subscription
RPC to have an optional existing subscription-id rather than
define a separate RPC. However, my preference is that the
existing subscription is deleted and recreated (or if we allow
the client to specify the subscription-id then they could just
overwrite the subscription)
* Holger: Overwrite is a neat idea, but delete/recreate would
also be sufficient.
Wilton, et al. Expires 4 September 2025 [Page 122]
Internet-Draft YANG-Push Lite March 2025
* Rob: Related to this, do we allow the client to optionally
name dynamic subscriptions (what is config and dynamic
subscription names collide)?
4. For operational data, should be list dynamic receivers in the
receiver list so that they are handled the same as configured
subscription? Or should the information for them be inlined in
the subscriptions container?
* Rob this requires further thought on exactly how configured/
dynamic subscriptions may to underlying transport sessions.
I.e., how fixed or flexible is this depending on the
transport.
5. Proposal is to make specifying an encoding mandatory.
D.8. Issues related to Subscription Lifecycle
1. Should subscription-started notification include a fingerprint of
the schema that is covered by the subscription that would
guaranteed to change if the subscription changes?
* Rob: I think that we should do this (i.e., as optimized
version of content-id)
* Would this also be impacted by a change to access control?
(Rob: Probably not)
* *Thomas would like to align to the same mechanism in YANG
Push, i.e., in the existing drafts, and we should use the same
mechanism*
* Rob: I would like to understand what the long term complete
solution is here.
* Benoit: Also related to the data manifest draft (in WGLC in
OPSWG.)
- Should discuss all of this together. IETF 122 discussion.
2. If a subscription references a filter, then should that be
included inline in the subscription started notification (as per
the RFC 8641 text), or should it indicate that it is a referenced
filter?
* Thomas: Do we need referenced filters at all? Subscriptions
could be simplified if everything was done inline.
Wilton, et al. Expires 4 September 2025 [Page 123]
Internet-Draft YANG-Push Lite March 2025
* gNMI is only done inline.
* Juniper also supports filters.
* Thomas try to simplify as much as possible, then do we need
templating?
3. When a subscription is terminated, should it be MUST NOT send any
more notifications after the terminated message, or SHOULD NOT?
For a dynamic subscription, should the RPC be synchronous and not
reply until it knows that all queues have been drained?
* Holger, Thomas, Benoit: MUST NOT
* James: SHOULD NOT
* MUST NOT is clearer from an implementation POV, but probably
doesn't really matter.
* What does the receiver do when it gets this message anyway.
4. Is a publisher allowed to arbitrarily send a sync-on-start
resync, e.g., if it detects data loss, or should it always just
terminate and reinitialize the subscription?
* Holger, terminate & recreate.
* gNMI, not specified.
* Thomas: Keep this as implementation detail.
* Sequence-id indicates that a client is dropping message
anyway.
* Receiver can already monitor and see that there is a problem
anyway.
5. If the parameters for a subscription change in any way (e.g., the
config changes for a configured subscription, or a referenced
filter changes in a dynamic subscription) then do we want to say
that the subscription MUST be killed and recreated. I.e., with
subscription-terminated/subscription-started notifications?
(Section 11)
* Holger, kill/re-create.
* Collector would need to no.
Wilton, et al. Expires 4 September 2025 [Page 124]
Internet-Draft YANG-Push Lite March 2025
* Ebben: Includes addition or deletion of the path.
* Benoit: Which parameters are changing, this could impact. It
depends. Maybe forcing it down keeps it simple. Would need
further definition of what parameters would cause this to be
pulled down.
* Locally relevant, e.g., modifying transport parameters doesn't
force a change.
* Benoit: If you are not sure what you are doing you must
recreate.
6. Should we have a YANG Action to reset a receiver or a
subscription? E.g., discussed in Section 9.1.5.
* There seems to be consensus that having/keeping such a YANG
action is useful if a configured subscription is stuck.
* Further discussion is needed to indicate where such an RPC
should be in the data model, and what effect it should have:
- It could be under the subscription list, which would
effectively be equivalent to forcing the subscription to
terminate and re-initialise across all receivers.
- It could also be under the receiver list, which would
effectively be equivalent to forcing all subscriptions
using that receiver to terminate and re-initialise.
- *We also need to consider whether this would clear
subscription counters or not.*
- *We also consider whether we need any text to rate limit
requests, e.g., in the security considerations section.*
- *We also need to consider whether configured subscription
MAY/SHOULD share transport sessions where possible, or
whether each subscription uses a separate transport
session, or whether this is down to the transport session
definition. This decision may impact the design of the
data model, and pehaps the transport requirements text.*
- *Rob: I've written up some text for the reset action on a
subscription and under the receiver (that applies to all
subscriptions that reference the receiver configuration).
Unlike the existing reset action, I've removed the return
parameter (timestamp of when it took effect), and I think
Wilton, et al. Expires 4 September 2025 [Page 125]
Internet-Draft YANG-Push Lite March 2025
that we should allow it to be processed asynchronously
w.r.t the RPC caller. Authors, please check the latest
text.*
7. Should we support configurable subscription-level keepalives?
* This would probably entail periodically sending a small
message on on-change subscriptions so that the receiver
(message broker) knows that the collection is still alive and
active.
* The presumption is that would be configurable option on an on-
change subscription (configured or dynamic)
* Note, some transport sessions may already support keepalives,
which is a separate, transport specific consideration.
* An alternative would be to configure a joint periodic and on-
change subscription, but depending on the keepalive interval
this would likely involve sending more data on a periodic
basis.
* Another alternative is to monitor the operational state of the
subscription to keep that all the expected subscriptions are
active.
* *Discussed, but no consensus reached yet*
D.9. Issues related to Performance, Reliability & Subscription
Monitoring
D.9.1. Issues/questions related to operational data:
1. Should we define some additional operational data to help
operators check that the telemetry infrastructure is performing
correctly, to get an approximation of the load, etc.
* Rob: probably, but lower priority.
2. Should dynamic subscriptions use the same receivers structure as
for configured subscriptions, or should they be inline in the
configured subscription?
* Thomas: Two sets of counters, one is at the subscription which
is about fetching the data, and the other is on the receiver.
* James: Can think of some uses cases where listing drop
counters per subscription may be helpful.
Wilton, et al. Expires 4 September 2025 [Page 126]
Internet-Draft YANG-Push Lite March 2025
* Rob: Thinking about it further, it probably needs to be
separate, since for some transports, each subscription may
open a separate transport session to the receiver rather than
trying to mux into a single transport (e.g., TCP).
D.10. Issues related to Conformance and Capabilities
1. Do we advertise that conformance via capabilities and/or YANG
features (both for configured and dynamic subscriptions)?
* The current doc uses a mixture of both (e.g., features for
supporting config vs dyanmic subscriptions), capabilities for
advertising other capabilities that either cannot be
advertised via features, or would arguably be too fine
grained.
2. For on-change, should a subscription be rejected (or not brought
up) if there are no on-change notifiable nodes? Alternative is
to offer implementation flexibility between these two approaches.
* Holger: Prefer for the subscription to be rejected.
3. CBOR SID encoding:
* In terms of conformance, we have SHOULD for CBOR, but the
draft is silent on whether this means with SIDs or not.
* Further discussion is required on how to manage SID files.
4. Check of the current approach in the draft of using a separate
tree for YP Lite capbilities rather than reusing the YP
capabilities (and augmentations) previously defined.
* Rob: The draft currently includes a separate tree, which I
think is necessary because the supported functionality is
different (e.g., dampening), and a implementation may support
both YANG Push and YANG Push Lite.
5. Further work and discussion is required for advertising
capabilities for filter paths. E.g., listing all of the paths
that support on-change could be a very long list. Related, does
the draft need to advertise at what points a publisher would
decompose a higher subscription into more specific subscriptions.
D.11. Issues related to the YANG Modules
None open.
Wilton, et al. Expires 4 September 2025 [Page 127]
Internet-Draft YANG-Push Lite March 2025
D.12. Issues related to the Security Considerations (& NACM filtering)
1. Need to consider how NACM applies to YANG Push Lite, which may
differ for dynamic vs configured subscription, but generally we
want the permissions to be checked when the subscription is
created rather than each time a path is accessed.
* (James) Take out tight binding to NACM from YANG Push Lite
altogether. I.e., decouple YANG Push Lite from what security
mechanism is being used.
* (Rob) Another choice could be to use NACM as an example rather
than the only way.
2. Where should this be in the document (current it in the security
considerations section)
3. Do we want to retain the the current text in Section 7
introduction related to terminating a subscription if permissions
change?
4. Also note, text was removed from the transport section related to
RPC authorization, and which should be moved to an application
(rather than transport) layer security mechanism.
D.13. Issues related to the IANA
1. Need to add in registration for ietf-yp-lite-capabilities.yang
D.14. Issues related to the Appendixes
D.14.1. Examples related issues/questions:
1. Not a question, but a note that most of the examples need to be
updated to reflect the data models currently in the draft.
D.15. Summary of closed/resolved issues
This appendix is only intended while the authors/WG are working on
the document, and should be deleted prior to WG LC.
1. Rename subscription-terminated to subscription-stopped (Change
rejected 21 Feb 25, unnecessary renaming.)
2. MUST use envelope, hostname and sequence-number (and event-time)
(Decided 21 Feb 25)
Wilton, et al. Expires 4 September 2025 [Page 128]
Internet-Draft YANG-Push Lite March 2025
3. Don't mandate configured or dynamic subscriptions, allow
implementations to implement one or both of them. (Decided 21
Feb 25)
4. Dynamic susbcriptions to require the encoding to be specified.
(Decided 21 Feb 25)
5. DSCP settings are only specified under the receiver (for
configured subscriptions) (Decided 21 Feb 25)
Authors' Addresses
Robert Wilton (editor)
Cisco Systems
Email: rwilton@cisco.com
Holger Keller
Deuetsche Telekom
Email: Holger.Keller@telekom.de
Benoit Claise
Huawei
Email: benoit.claise@huawei.com
Ebben Aries
Juniper
Email: Ebben Aries exa@juniper.net
James Cumming
Nokia
Email: james.cumming@nokia.com
Thomas Graf
Swisscom
Email: Thomas.Graf@swisscom.com
Wilton, et al. Expires 4 September 2025 [Page 129]