Signaling control/forward plane information between network virtualization edges (NVEs)
draft-wu-nvo3-nve2nve-02
The information below is for an old version of the document.
| Document | Type | Active Internet-Draft (individual) | |
|---|---|---|---|
| Author | Qin Wu | ||
| Last updated | 2013-04-02 | ||
| Stream | (None) | ||
| Formats | plain text xml htmlized pdfized bibtex | ||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-wu-nvo3-nve2nve-02
Network Virtualization Overlays Working Q. Wu
Group Huawei
Internet-Draft April 3, 2013
Intended status: Standards Track
Expires: October 5, 2013
Signaling control/forward plane information between network
virtualization edges (NVEs)
draft-wu-nvo3-nve2nve-02
Abstract
This document focuses on control plane aspect related to both tenant
system to NVE control interface and NVE to Oracle control interface
NVE use to enable communication between tenant systems, which is
complementary to [draft-kreeger-nvo3-hypervisor-nve-cp] that
describes the high level control plane requirements related to the
interaction between tenant system and NVE when the two entities are
not co-located on the same physical device.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 5, 2013.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Wu Expires October 5, 2013 [Page 1]
Internet-Draft NVE2NVE April 2013
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions used in this document . . . . . . . . . . . . . . 4
3. NVO3 Control plane Overview . . . . . . . . . . . . . . . . . 5
4. Mapping table entry at the NVE and Information mapping
authority . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1. Mapping table Entry Fields relationship . . . . . . . . . 8
4.2. Multihoming support using one vNIC . . . . . . . . . . . . 10
4.3. Interconnection functionality . . . . . . . . . . . . . . 10
5. NVE to Oracle Control plane protocol functionality . . . . . . 13
5.1. NVE connect/disconnect notification . . . . . . . . . . . 13
5.2. VN membership Registration and Query . . . . . . . . . . . 13
5.3. Address Mapping information reflection/distribution . . . 14
6. Hypervisor-to-NVE Control Plane Protocol Functionality . . . . 15
6.1. Multiple vNIC addresses association . . . . . . . . . . . 15
7. Key functions aspect for signaling control/forwarding info
to NVEs . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1. Create and Update tenant Virtual Network (VN) . . . . . . 16
7.2. Associate the NVE and tenant system with VN context . . . 16
7.3. Populate mapping tables information at the local NVE . . . 17
7.4. Distribute the mapping table information to remote
NVEs in the VN . . . . . . . . . . . . . . . . . . . . . . 17
7.5. The mapping table information update at the NVE when
VM moves or connection fails . . . . . . . . . . . . . . . 17
7.6. The VN context re-association at the NVE when VM moves . . 18
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
9. Security Considerations . . . . . . . . . . . . . . . . . . . 20
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.1. Normative References . . . . . . . . . . . . . . . . . . . 21
10.2. Informative References . . . . . . . . . . . . . . . . . . 21
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 22
Wu Expires October 5, 2013 [Page 2]
Internet-Draft NVE2NVE April 2013
1. Introduction
In [I.D-ietf-nvo3-overlay-problem-statement], two control planes are
identified to realize an overlay solution:
o NVE to Oracle control plane.
o Tenant system to NVE control plane.
Where NVE to Oracle Control plane is used to deal with address
mapping dissemination and Tenant System to NVE control plane is used
to deal with VM attachment and detachment.
In [I.D-ietf-nvo3-framework], three control plane components are
defined to build these two control planes and provide the following
capabilities:
o Auto-provision/service discovery
o Address advertisement
o Tunnel Managment
In [I.D-fw-nvo3-server2vcenter],the control interface between NVE and
Oracle backend system or Information Mapping Authority is defined to
provide the capability:
o Enforce the network policy for each VM in the path from the NVE
Edge associated with VM to the Tenant End System.
o Populate forwarding table in the path from the NVE Edge associated
with VM to the Tenant End System in the data center.
o Populate mapping table in each NVE Edge that is in the virtual
network across data centers under the control of the Director.
This document focuses on control plane aspect related to both tenant
system to NVE control interface and NVE to Oracle control interface
NVE use to enable communication between tenant systems, which is
complementary to [draft-kreeger-nvo3-hypervisor-nve-cp] that
describes the high level control plane requirements related to the
interaction between tenant system and NVE when the two entities are
not co-located on the same physical device.
Wu Expires October 5, 2013 [Page 3]
Internet-Draft NVE2NVE April 2013
2. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [RFC2119].
Site :
If multiple tenant systems connect to the VN through one NVE, the
collection of these tenant systems and the NVE associated with
these tenant systems are referred to as a site or virtualization
network subnet.
Tenant System:
A physical or virtual system that can play the role of a host, or
a forwarding element such as a router, switch, firewall, etc. It
belongs to a single tenant and connects to one or more VNs of that
tenant.
vNIC:
A vNIC is similar to a physical NIC. Each virtual machine has one
or more vNIC adapters that it uses to communicate with both the
virtual and physical networks. Each vNIC has its own MAC address
and can be assigned one or more IP address just like a NIC found
in a non virtualized machine.
Wu Expires October 5, 2013 [Page 4]
Internet-Draft NVE2NVE April 2013
3. NVO3 Control plane Overview
Figure 1 shows the example NVO3 Networking architecture to give an
overview of NVO3 control plane for interconnection between VNs or
between VN and Non-VN. There are 4 basic network components that
make up networking architecture: Tenant system, local NVE, remote NVE
and Information mapping authority. This example NVO3 networking
architecture assumes that:
o One tenant system, can host multiple virtual machines. Each
virtual machine has one or more vNIC adapters that it uses to
communicate with both the virtual and physical networks.
o One tenant system or a NVE may belong to one tenant VN or several
tenant VNs, e.g., TS4 and NVE Edge4 belong to both VN2 and VN3.
o If one tenant system belongs to multiple tenant VNs, it may have
one VM with multiple vNICs and connect to each tenant VN by using
each of vNICs being attached to one or multiple NVEs,e.g., VM1
connect to VN1 by being attached to NVE Edge 1.
o If one tenant system belongs to multiple tenant VNs, it may have
multiple VM with each having one vNIC and connect to each tenant
VN by using each VM vNIC being attached to one or multiple NVEs.
o One NVE only belongs to one site. One site may belong to one
tenant VN or several tenant VN, e.g., Site 2 belong to both VN2
and VN3.
o If one tenant system in one VN want to communicate with one tenant
system in another VN, the interconnection functionality or
information mapping authority or NVE controller may get involved
to help establish interconnection between VN or setup tunnel
between NVEs associated with the tenant system.
Wu Expires October 5, 2013 [Page 5]
Internet-Draft NVE2NVE April 2013
+---------------+-------------+--------------+
| VN1 | +--------+ | +--------+ |
| | |VM1VM2VM3 | |VM4VM5VM6 |
| | +--------+ | +--------+ |
| | | | | | | |
| | | TS1 | | | TS2 | |
| | | | | | | |
| | +--------+ | +--------+ |
| | +---------+ | +---------+|
| -+-|NVE Edge1+-+---+NVE Edge2++-
| // | +---------+ | +---------+| \\
| | |Site1 | | |
| | +-------------+ +VN3--------+---+------------+
| |--+---+ +---+ | |+---+ +---|--+ |
| |VMd | | | | || | | |VMh |
| | | | |NVE| | ||NVE| | | | |
| | | | | | | || | | | | |
| |VMe T | | E | ,---------. | || E | | T |VMi |
| | | | | d | Interconnection | || d | | | | |
| | | S | | g |( )| || g | | S | | |
| |VMf | | e | `Functionality' | || e | | |VMj |
| | | 5 | | 5 | `---------' | || 6 | | 6 | | |
| |VMg | | | | || | | |VMk |
| |--|---+ ++--+ | |++--+ |---+--+ |
+-----------+--------------------+-----------+ | |
| | | |
| +VN2--------------+------------+ | |
. |... .............|Site2..... .| | |
.| | +---------+ .. |+---------+ |// |
. \\| |NVE Edge3+-----++NVE Edge4+-+ |
. | +---------+ |+---------+ | |
. | +--------+ .. | +--------+ | . |
. | | | .. | | | | . |
. | | TS3 | .. | | TS4 | | . |
. | | | .. | | | | . |
. | +--------+ .. | +--------+ | . |
. | |VM7VM8VM9 .. | |VMaVMbVMc | . |
....| ---------+......|.---------+ |.. |
+-----------------+------------+ |
+----------------------------+
Figure 1: Example NVO3 control plane Overview
Wu Expires October 5, 2013 [Page 6]
Internet-Draft NVE2NVE April 2013
4. Mapping table entry at the NVE and Information mapping authority
Tenant system VNICs should be able to directly connect to multiple
VNs without needing to traverse a NVE or gateway. Therefore every
NVE pair( local NVE and remote NVE ) associated with the tenant
system vNIC MUST maintain one or multiple mapping table entry for
each currently attached VNIC of tenant system. Each mapping table
entry should include a IP address of vNIC and corresponds to the
connection to each VN. Each mapping table entry conceptually may
contain all or a sub set of the following fields:
o The tunnel interface identifier (tunnel-if-id) of the tunnel
between the remote NVE and the local NVE where the tenant system
is currently attached. The tunnel interface identifier is
acquired during the tunnel creation.
o The MAC address of the attached TS vNIC. This MAC address is
obtained from auto-discovery protocol between Tenant System and
its local NVE.
o The IP address of the attached TS vNIC. This IP address is
obtained from auto-discovery protocol between Tenant System and
its local NVE.
o The logical interface identifier (e.g., VLAN ID, internal vSwitch
Interface ID connected to a VM) of the access link between the
tenant system and the local NVE. This field is required to
associate with Tenant System vNIC if local NVE is an external NVE
to Tenant system and is internal to the local NVE and is used to
associate the tunnel to the access link where the tenant system is
attached.
o The MAC address of the local NVE associated with the tenant
system.
o The IP address of the local NVE associated with the tenant system.
o The Identifier of VN context-VNID. This Identifier is obtained
from auto-discovery protocol between Tenant System and its local
NVE.
In addition, Oracle backend system or information mapping authority
may also maintain a mapping table entry for each currently attached
tenant system vNIC or each newly joined NVE. Each mapping table
entry conceptually may contain all or a sub set of the following
fields:
Wu Expires October 5, 2013 [Page 7]
Internet-Draft NVE2NVE April 2013
o The MAC address of the attached TS vNIC. This MAC address is
obtained from auto-discovery protocol between Tenant System and
its local NVE.(Optional)
o The IP address of the attached TS vNIC. This IP address is
obtained from auto-discovery protocol between Tenant System and
its local NVE. (Optional)
o The logical interface identifier (e.g., VLAN ID, internal vSwitch
Interface ID connected to a VM) of the access link between the
tenant system and the local NVE. This field is required to
associate with Tenant System vNIC if local NVE is an external NVE
to Tenant system and is internal to the local NVE and is used to
associate the tunnel to the access link where the tenant system is
attached.
o The MAC address of the local NVE associated with the tenant
system.
o The IP address of the local NVE associated with the tenant system.
o The Identifier of VN context-VNID. This Identifier is obtained
from auto-discovery protocol between Tenant System and its local
NVE.
4.1. Mapping table Entry Fields relationship
One Tenant system can host multiple VMs. Each VM has one or more
vNIC adapters that it uses to communicate with both the virtual and
physical networks. Each vNIC must have one and only one unique MAC
address. In addition, each vNIC have at least one IP address. When
a VM using one vNIC connects to multiple VNs,the vNIC should be
assigned with multiple IP addresses with each connecting to different
VN. In this case, VM may create multiple binding cache entries with
each associating one of multiple IP addresses to the same unique vNIC
MAC address. vNIC MAC address may be modified or assigned with a new
MAC address at any time. However vNIC should not use more than one
MAC addresses to connect to multiple VNs at the same time. When
multiple vNICs hosted in the same VM connect to multiple VNs, it is
allowed that some of these vNICs may connect to different VNs through
the same NVE.
Tenant System (TS)
|
+--------------+--------------+
| | |
| |
VM1 VM2 ..... VMx
Wu Expires October 5, 2013 [Page 8]
Internet-Draft NVE2NVE April 2013
|
|---------+--------+
| | |
| | |
vNIC1 vNIC2 ... vNICx
|
|
+------+------+
| | |
VN1 VN2 ...VNx
Figure 2. VM information Hierarchy
VM1
|
|---------+--------+
| | |
| | |
vNIC1 vNIC2 ... vNICx
|
|
|
NVE
|
+-------+------+
| | |
VN1 VN2 VN3
Binding Cache Database
VM1 vNIC1's Binding
binding[VNIC1 MAC addr, IP1 addr, BID1]
binding[vNIC1 MAC addr, IP2 addr, BID2]
binding[vNIC1 MAC addr, IP3 addr, BID3]
Figure 3 Simultaneous multiple connections
for Layer 3 Virtual Network Service
VM1
|
|---------+--------+
| | |
| | |
vNIC1 vNIC2 ... vNICx
|
|
Wu Expires October 5, 2013 [Page 9]
Internet-Draft NVE2NVE April 2013
|
NVE
|
+-------+------+
| | |
VN1 VN2 VN3
Binding Cache Database
VM1 vNIC1's Binding
binding[VNIC1 MAC addr, VLAN ID1, BID1]
binding[vNIC1 MAC addr, VLAN ID2, BID2]
binding[vNIC1 MAC addr, VLAN ID3, BID3]
Figure 4. Simultaneous multiple connections
for Layer 2 Virtual Network Service
4.2. Multihoming support using one vNIC
Tenant System vNIC may use several IP addresses to connect to
multiple VNs. Each IP address corresponding to each connection to
VN. In order to support connecting to multiple VNs using a single
vNIC, Tenant system may create a Binding Identifier (BID) to each IP
address that is used to connect to VN. The BID should be unique for
a given Tenant System vNIC MAC address.If the tenant system vNIC has
only one IP address, the assignment of a BID is not needed until it
has multiple IP addresses for a single vNIC, at which time all of the
IP addresses of vNIC MUST be mapped to BIDs. BID is suggested to be
stored in the mapping table entry at the NVE and information mapping
authority.
4.3. Interconnection functionality
Suppose the tenant system A hosts only one VM that have only one vNIC
adapter, when the tenant system A plays the role of interconnection
functionality to connect two VN, three cases should be considered.
(a) Both two VNs support Layer 3 forwarding;
(b) Both two VNs support layer 2 forwarding;
(c) One VN support Layer3 forwarding and the other VN support
layer 2 forwarding;
For (a), tenant system A vNIC or external system that is close to
tenant system A should support layer 3 forwarding functionality.
When source tenant system in one VN communicates with destination
tenant system in another VN through the tenant system A, if tenant
system A vNIC support layer 3 forwarding, the tenant system A should
Wu Expires October 5, 2013 [Page 10]
Internet-Draft NVE2NVE April 2013
forward IP packets on the behalf of source Tenant System and
destination tenant system irrespective of data plane encapsulation
format(e.g., VXLAN or NVGREW, MPLS over GRE). If two VNs use
different data plane encapsulation format, the tenant system A should
also support converting one data plane encapsulation format into
another. If tenant system A vNIC doesn't support layer 3
forwarding,the external system that is close to tenant system A
should associate vNIC to local NVE using TS vNIC MAC address and VLAN
tag information and forward IP packets on the behalf of source tenant
system and destination tenant system.
For (b), tenant system A vNIC or external system that is close to
tenant system A should support layer 2 forwarding functionality.
When source tenant system in one VN communicates with destination
tenant system in another VN through the tenant system A, if tenant
system A support layer 2 forwarding, the tenant system A should know
which tenant systems connecting to itself are allowed for layer 2
forwarding and then forward layer 2 frames on the behalf of source
Tenant System and destination tenant system based on forwarding
allowed list. If two layer 2 VNs support different data plane
encapsulation format, the tenant system A should also support
converting one data plane encapsulation format to another. If tenant
system A vNIC doesn't support layer 2 forwarding,the external system
that is close to tenant system A should associate vNIC to local NVE
using TS vNIC MAC address and VLAN tag information and forward layer
2 frames on the behalf of source tenant system and destination tenant
system.
For (c), tenant system A or external system that is close to tenant
system A should support both layer 2 forwarding and layer 3
forwarding. When source tenant systems in layer 2 VN communicates
with destination tenant system in layer 3 VN through the tenant
system A, if tenant system A support both layer 2 and layer 3
forwarding the tenant system A should support translating layer 2
frame into layer 3 packet and forward traffic between layer 2 VN and
layer 3 VN. If two VNs support different data plane encapsulation
format, the tenant system A should also support converting one data
plane encapsulation format to another. If tenant system A vNIC
doesn't support layer 2 forwarding or layer3 forwarding,the external
system that is close to tenant system A should associate vNIC to
local NVE using TS vNIC MAC address and VLAN tag information and
forward traffic on the behalf of source tenant system and destination
tenant system.
When the tenant system A plays the role of interconnection
functionality to connect between VN and Non-VN, suppose source tenant
system in one VN communicates with destination end device in Non-VN
environment through the tenant system A, the tenant system A acts as
Wu Expires October 5, 2013 [Page 11]
Internet-Draft NVE2NVE April 2013
NVO3 GW between VN and Non-VN in this case and should be explicitly
configured with a list of destination MAC addresses that allows
passed to the Non-VN environment. For outgoing frames on VN
connected interface, the tenant system A decapsulates NVO3 outer
header and forward the inner frame to Non-VN environment based on
configured allowed list. For incoming frames on non-VN connected
interface, the tenant system A should map the incoming frames from
end device to specific VN based on inner Ethernet frame information
(e.g., VLAN ID).
Wu Expires October 5, 2013 [Page 12]
Internet-Draft NVE2NVE April 2013
5. NVE to Oracle Control plane protocol functionality
The core functional entities for NVE to Oracle Control plane
infrastructure are the NVE and Oracle backend system. The Oracle
backend system is responsible for maintaining the tenant system
VNIC's reachability state and is the topological anchor point for the
Tenant system vNIC MAC address or vNIC Name. The NVE is the entity
that performs the address mapping management on behalf of tenant
system vNIC, and it resides on the access link where the tenant
system is anchored. The NVE is responsible for detecting the VM's
movements to and from the access link and for initiating location
binding registrations to the tenant system's Oracle backend system.
There can be multiple Oracle backend system in a VN each serving a
different group of tenant system.
5.1. NVE connect/disconnect notification
When a tenant system connects to one VN by attaching to a local NVE,
the local NVE should also be added into VN context together with
tenant system information. This helps Oracle Backend System know
with which NVE a group of the tenant systems are attached or current
location of these tenant systems. When the last tenant system is
disconnected to one VN through one local NVE, this local NVE should
also be removed from VN context. This should also be updated to
Oracle Backend system and let Oracle backend system know that there
are no tenant system associated with that NVE.
5.2. VN membership Registration and Query
In order to enable tenant system A to communicate with any tenant
system that is not under the same local NVE, the mapping table should
be distributed to all the remote NVEs that belong to the same VN even
through there is no tenant system which communicates with tenant
system A behind that remote NVE. However how should local NVE know
the list of remote NVEs that belong to the same VN as local NVE? In
order to tackle this, when a tenant system connects to one VN by
attaching to a local NVE, VN membership (e.g., VNID, VN Name, a list
of NVE that belong to VN) should be registered to the Oracle Backend
system. When local NVE needs to know which remote NVEs it should
forward a data packet, Oracle backend system can be queried by the
local NVE. The Oracle backend system can redirect the query from
local NVE to the remote NVEs based on VN membership registration and
obtain answer from the right remote NVE. In addition, VM membership
may contain detailed mapping between tenant system,NVE and VN in the
form of TESID=<VNID, NVE_ID,TS_ID>. In this case, Oracle backend
system can directly supply answer for the request from the local NVE.
Wu Expires October 5, 2013 [Page 13]
Internet-Draft NVE2NVE April 2013
5.3. Address Mapping information reflection/distribution
Data plane learning can be used to build mapping table without need
for control plane protocol. However it requires each data packet to
be flooded to the whole VN. In order to eliminate flooding
introduced by data plane learning, a control protocol is needed to
provide both MAC address and IP address in the form of mapping
information. When VN membership registration complete, the NVE can
forward such address mapping information directly to all the remote
NVEs based on VN membership, alternatively, the NVE also can forward
such address mapping information indirectly to the Oracle backend
system and let Oracle backend system to reflect the address mapping
information to all the relevant remote NVEs based on VN membership.
Wu Expires October 5, 2013 [Page 14]
Internet-Draft NVE2NVE April 2013
6. Hypervisor-to-NVE Control Plane Protocol Functionality
6.1. Multiple vNIC addresses association
Typically, a VNIC is assigned a single MAC address and a single IP
address. However, a vNIC may be assigned multiple IP addresses with
each to connect to one VN. In such case, BID may be assigned for
each IP address of vNIC when tenant system vNIC wants to register
multiple IP address with its MAC address simultaneously to the local
NVE. If a tenant system vNIC has only one IP address, the assignment
of a BID is not needed until it has multiple IP addresses to register
with, at which time all of the IP addresses of vNIC MUST be mapped to
BIDs. When a tenant system vNIC registers a given BID for the first
time it MUST send BID together with the IP address. For any
subsequent registrations that either re-register or de-register the
same BID, the TS only need send BID and does not need to send IP
address associated with BID.
Wu Expires October 5, 2013 [Page 15]
Internet-Draft NVE2NVE April 2013
7. Key functions aspect for signaling control/forwarding info to NVEs
7.1. Create and Update tenant Virtual Network (VN)
The tenant virtualization network(VN) is a collection of tenant
systems, Network Virtualization Edges (NVE)(s) and end systems that
are interconnected with each other. The tenant VN also consists of a
set of sites where each can send traffic directly to the other.
In order to create or update a tenant VN, when a Tenant System is
attached to a local NVE, the tenant system should inform the attached
local NVE which VN the tenant system belong to.
o If the tenant system are the first participant in the VN through
the local NVE, the tenant system and associated local NVE should
be firstly added to the VN and the mapping table should be setup
at the local NVE for each attached tenant system.
o If both the tenant system and the local NVE are not on the VN, the
tenant system and associated local should be firstly added to the
VN and then the mapping table associated with this tenant system
should be setup at the local NVE and distributed to the other
remote NVEs that belong to the same VN.
o If the local NVE is on the same tenant VN as the tenant system
associated with the local NVE, only the tenant system needs to be
added into the VN, i.e., the local NVE only needs to distribute
mapping table at the local NVE to the other remote NVEs that
belong to the same tenant VN.
o If the local NVE is not on the same tenant VN as the tenant system
associated with that local NVE, the local NVE should firstly be
added into the VN and then distributes the new mapping table at
the local NVE to the other remote NVEs that belong to the same
tenant VN.
o If one tenant system is the last participant connecting to the VN
through local NVE, when this tenant system leave the VN, the local
NVE associated with this tenant system should be removed from the
VN.The mapping table associated with this tenant system should be
removed from the local NVE associated with this tenant system.
7.2. Associate the NVE and tenant system with VN context
The VN context includes a set of configuration attributes defining
access and tunnel policies and (L2 and/or L3) forwarding functions.
When a Tenant System is attached to a local NVE, a VN network
instance should be allocated to the local NVE. The tenant system
Wu Expires October 5, 2013 [Page 16]
Internet-Draft NVE2NVE April 2013
should be associated with the specific VN context using virtual
Network Instance(VNI). The tenant system should also inform the
attached local NVE which VN context the tenant system belong to.
Therefore the VN context can be bound with the data path from the
tenant system to the local NVE and the tunnel from local NVE
associated with the tenant system and all the remote NVEs that belong
to the same VN as the local NVE. For the data path from the tenant
system and the local NVE, the network policy can be installed on the
underlying switched network and forwarding tables also can be
populated to each network elements in the underlying network based on
the specific VNI associated with the tenant system. For the tunnel
from local NVE to the remote NVEs, the traffic engineering
information can be applied to each tunnel based on VNI associated
with the tenant system.
7.3. Populate mapping tables information at the local NVE
In some cases, two tenant systems may be attached to the same local
NVE. In order to allow the NVE to locally route traffic between two
tenant systems that are attached to the same NVE, the mapping table
that maps a final destination address to the proper tunnel should be
populated at the local NVE.
In some cases, two tenant systems may connect to the different VNs
through the same interconnection functionality, in order to allow two
tenant systems communication between two VNs, the mapping table that
maps a final destination address to the proper tunnel should be
populated in both NVE associated with two communicated tenant system
and the interconnection functionality associated corresponding NVE.
7.4. Distribute the mapping table information to remote NVEs in the VN
When the packet sent from one tenant system arrives at the ingress
NVE associated with that tenant system, in order to determine which
tunnel the packet needs to be sent to, the mapping table that maps a
final destination address to the proper tunnel should also be
distributed to all the remote NVEs in the VN using a control plane
protocol or dynamic data plane learning. The mapping table may be
advertised directly to other remote NVEs that belong to the same VN
or firstly advertised to the centralized controller that maintain
global view of NVEs that belong to the same VN and then let the
centralized controller distribute the mapping tables to all the
relevant remote NVEs that belong to the same VN.
7.5. The mapping table information update at the NVE when VM moves or
connection fails
In some cases, one tenant system may be detached from one NVE and
Wu Expires October 5, 2013 [Page 17]
Internet-Draft NVE2NVE April 2013
move to another NVE. In such cases, the mapping table should be
removed from the NVE to which the tenant system was previously
attached and the new mapping table should be created at the new NVE
to which the tenant system is currently attached. Such mapping table
should be updated at each remote NVE associated with the tenant
system and the new NVE.
In some cases, one tenant system may fail to connect to the VN
through the NVE. In such cases, the mapping table should be removed
from the NVE to which the tenant system is currently attached. In
addition, the mapping table should be updated at each remote NVE in
the same VN through which the tenant system is communicating with the
destination tenant system.
7.6. The VN context re-association at the NVE when VM moves
In some cases, one tenant system may be detached from one NVE and
move to another NVE. In such cases, the VN context should be moved
from the NVE to which the tenant system was previously attached to
the new NVE to which the tenant system is currently attached. In
order to achieve this, the per tenant system VN context can be
maintained at the centralized database and be retrieved at the new
place based on the VN Identifier (VNID).
Wu Expires October 5, 2013 [Page 18]
Internet-Draft NVE2NVE April 2013
8. IANA Considerations
This document has no actions for IANA.
Wu Expires October 5, 2013 [Page 19]
Internet-Draft NVE2NVE April 2013
9. Security Considerations
TBC.
Wu Expires October 5, 2013 [Page 20]
Internet-Draft NVE2NVE April 2013
10. References
10.1. Normative References
[I.D-ietf-nvo3-framework]
Lasserre, M., "Framework for DC Network Virtualization",
ID draft-ietf-nvo3-framework-00, September 2012.
[I.D-ietf-nvo3-overlay-problem-statement]
Narten, T., "Problem Statement: Overlays for Network
Virtualization",
ID draft-ietf-nvo3-overlay-problem-statement-02,
Feburary 2013.
[I.D-kreeger-nvo3-hypervisor-nve-cp]
Kreeger, L., "Network Virtualization Hypervisor-to-NVE
Overlay Control Protocol Requirements",
ID draft-kreeger-nvo3-hypervisor-nve-cp-01, Feburary 2013.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", March 1997.
10.2. Informative References
[I.D-fw-nvo3-server2vcenter]
Wu, Q. and R. Scott, "Network Virtualization
Architecture", ID draft-fw-nvo3-server2vcenter-01,
January 2013.
Wu Expires October 5, 2013 [Page 21]
Internet-Draft NVE2NVE April 2013
Author's Address
Qin Wu
Huawei
101 Software Avenue, Yuhua District
Nanjing, Jiangsu 210012
China
Email: bill.wu@huawei.com
Wu Expires October 5, 2013 [Page 22]