Skip to main content

A YANG Data Model for Transport Network Client Signals
draft-zheng-ccamp-client-signal-yang-03

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft whose latest revision state is "Replaced".
Authors Haomian Zheng , Aihua Guo , Italo Busi , Yunbin Xu , Yang Zhao , Xufeng Liu , Giuseppe Fioccola
Last updated 2018-10-22
Replaces draft-zheng-ccamp-otn-client-signal-yang
Replaced by draft-ietf-ccamp-client-signal-yang
RFC stream (None)
Formats
Stream Stream state (No stream defined)
Consensus boilerplate Unknown
RFC Editor Note (None)
IESG IESG state I-D Exists
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-zheng-ccamp-client-signal-yang-03
CCAMP Working Group                                             H. Zheng
Internet-Draft                                                    A. Guo
Intended status: Standards Track                                 I. Busi
Expires: April 25, 2019                              Huawei Technologies
                                                                   Y. Xu
                                                                   CAICT
                                                                 Y. Zhao
                                                            China Mobile
                                                                  X. Liu
                                                          Volta Networks
                                                             G. Fioccola
                                                     Huawei Technologies
                                                        October 22, 2018

         A YANG Data Model for Transport Network Client Signals
                draft-zheng-ccamp-client-signal-yang-03

Abstract

   A transport network is a server-layer network to provide connectivity
   services to its client.  The topology and tunnel information in the
   transport layer has already been defined by Traffic-engineered models
   and OTN models, however, the access to the network has not been
   described.  These information is useful to both client and provider.

   This draft describe how the client signals are carried over transport
   network and defined corresponding YANG data model which is required
   during configuration procedure.  More specifically, several client
   signal (of transport network) models including ETH, STM-n, FC and so
   on, are defined in this draft.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 25, 2019.

Zheng, et al.            Expires April 25, 2019                 [Page 1]
Internet-Draft     Transport Client Signals YANG Model      October 2018

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Terminology and Notations . . . . . . . . . . . . . . . . . .   3
   3.  Transport Network Client Signal Overview  . . . . . . . . . .   4
   4.  YANG Model for Transport Network Client Signal  . . . . . . .   4
     4.1.  YANG Tree for Ethernet Service  . . . . . . . . . . . . .   4
     4.2.  YANG Tree for other Transport Network Client Signal Model   8
   5.  YANG Code for Transport Network Client Signal . . . . . . . .   8
     5.1.  The ETH Service YANG Code . . . . . . . . . . . . . . . .   8
     5.2.  YANG Code for ETH transport type  . . . . . . . . . . . .  21
     5.3.  Other Transport Network client signal YANG Code . . . . .  28
   6.  Considerations and Open Issue . . . . . . . . . . . . . . . .  31
   7.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  31
   8.  Manageability Considerations  . . . . . . . . . . . . . . . .  31
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .  31
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  32
   11. Contributors  . . . . . . . . . . . . . . . . . . . . . . . .  32
   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  32
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  32
     12.2.  Informative References . . . . . . . . . . . . . . . . .  33
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  34

1.  Introduction

   A transport network is a server-layer network designed to provide
   connectivity services for a client-layer network to carry the client
   traffic transparently across the server-layer network resources.
   Currently there has been topology and tunnel model defined for
   transport network, such as [I-D.ietf-ccamp-otn-topo-yang] and
   [I-D.ietf-ccamp-otn-tunnel-model], which has described the network
   model between PEs.  However, there is a missing piece for the mapping

Zheng, et al.            Expires April 25, 2019                 [Page 2]
Internet-Draft     Transport Client Signals YANG Model      October 2018

   between the PE and the CE, which is expected to be solved in this
   document.

   This document defines a data model of all transport network client
   signals, using YANG language defined in [RFC7950].  The model can be
   used by applications exposing to a transport controller via a REST
   interface.  Furthermore, it can be used by an application for the
   following purposes (but not limited to):

   o  To request/update an end-to-end service by driving a new tunnel to
      be set up to support this service;

   o  To request/update an end-to-end service by using an existing
      tunnel;

   o  To receive notification with regard to the information change of
      the given service;

   The YANG model defined in this document is independent of control
   plane protocols and captures topology related information.
   Furthermore, it is not a stand-alone model, but augmenting from the
   TE topology YANG model defined in [I-D.ietf-teas-yang-te-topo].

2.  Terminology and Notations

   A simplified graphical representation of the data model is used in
   this document.  The meaning of the symbols in the YANG data tree
   presented later in this document is defined in
   [I-D.ietf-netmod-yang-tree-diagrams].  They are provided below for
   reference.

   o  Brackets "[" and "]" enclose list keys.

   o  Abbreviations before data node names: "rw" means configuration
      (read-write) and "ro" state data (read-only).

   o  Symbols after data node names: "?" means an optional node, "!"
      means a presence container, and "*" denotes a list and leaf-list.

   o  Parentheses enclose choice and case nodes, and case nodes are also
      marked with a colon (":").

   o  Ellipsis ("...") stands for contents of subtrees that are not
      shown.

Zheng, et al.            Expires April 25, 2019                 [Page 3]
Internet-Draft     Transport Client Signals YANG Model      October 2018

3.  Transport Network Client Signal Overview

   The transport network is usually a server-layer network designed to
   provide connectivity services for a client-layer network to carry the
   client traffic opaquely across the server-layer network resources.  A
   transport network may be constructed from equipments utilizing any of
   a number of different transport technologies such as the evolving
   optical transport infrastructure (SONET/SDH and OTN) or packet
   transport as epitomized by the MPLS Transport Profile (MPLS-TP).

   In the example of OTN as the transport network, a full list of G-PID
   was summarized in [RFC7139], which can be divided into a few
   categories.  The G-PID signals can be categorized into transparent
   and non-transparent.  Examples of transparent signals may include
   Ethernet, ODU, STM-n and so on.  In this approach the OTN devices do
   not is not aware of the client signal type, and this information is
   only necessary among the controllers.  Once OTN tunnel is set up,
   there is no switching requested on the client layer, and therefore
   only signal mapping is needed, without a client tunnel set up.  The
   other category would be non-transparent, such as Carrier Ethernet and
   MPLS-TP, with a switching request on the client layer.  Once the OTN
   tunnel is set up, a corresponding tunnel in the client layer has to
   be set up to carry services.  The models in this draft are applicable
   for both of the two above categories.

   It is also worth noting that some client signal can be carried over
   multiple types of transport networks.  For example, the Ethernet
   services can be carried over either OTN or Ethernet TE tunnels (over
   optical or microwave networks).  The model specified in this document
   allows the support from networks with different technologies.

4.  YANG Model for Transport Network Client Signal

4.1.  YANG Tree for Ethernet Service

module: ietf-eth-tran-service
    +--rw etht-svc
       +--rw globals
       |  +--rw named-bandwidth-profiles* [bandwidth-profile-name]
       |     +--rw bandwidth-profile-name    string
       |     +--rw bandwidth-profile-type?   etht-types:bandwidth-profile-type
       |     +--rw CIR?                      uint64
       |     +--rw CBS?                      uint64
       |     +--rw EIR?                      uint64
       |     +--rw EBS?                      uint64
       |     +--rw color-aware?              boolean
       |     +--rw coupling-flag?            boolean

Zheng, et al.            Expires April 25, 2019                 [Page 4]
Internet-Draft     Transport Client Signals YANG Model      October 2018

       +--rw etht-svc-instances* [etht-svc-name]
          +--rw etht-svc-name             string
          +--rw etht-svc-id?              yang:uuid
          +--rw etht-svc-descr?           string
          +--rw etht-svc-customer?        string
          +--rw etht-svc-type?            etht-types:service-type
          +--rw etht-svc-lifecycle?       etht-types:lifecycle-status
          +--rw te-topology-identifier
          |  +--rw provider-id?   te-types:te-global-id
          |  +--rw client-id?     te-types:te-global-id
          |  +--rw topology-id?   te-types:te-topology-id
          +--rw etht-svc-access-ports* [access-port-id]
          |  +--rw access-port-id                      uint16
          |  +--rw access-node-id?                     te-types:te-node-id
          |  +--rw access-ltp-id?                      te-types:te-tp-id
          |  +--rw service-classification-type?        identityref
          |  +--rw (service-classification)?
          |  |  +--:(port-classification)
          |  |  +--:(vlan-classification)
          |  |     +--rw outer-tag!
          |  |     |  +--rw tag-type?     etht-types:eth-tag-classify
          |  |     |  +--rw (individual-bundling-vlan)?
          |  |     |     +--:(individual-vlan)
          |  |     |     |  +--rw vlan-value?   etht-types:vlanid
          |  |     |     +--:(vlan-bundling)
          |  |     |        +--rw vlan-range?   etht-types:vid-range-type
          |  |     +--rw second-tag!
          |  |        +--rw tag-type?     etht-types:eth-tag-classify
          |  |        +--rw (individual-bundling-vlan)?
          |  |           +--:(individual-vlan)
          |  |           |  +--rw vlan-value?   etht-types:vlanid
          |  |           +--:(vlan-bundling)
          |  |              +--rw vlan-range?   etht-types:vid-range-type
          |  +--rw split-horizon-group?                string
          |  +--rw (direction)?
          |  |  +--:(symmetrical)
          |  |  |  +--rw ingress-egress-bandwidth-profile
          |  |  |     +--rw (style)?
          |  |  |        +--:(named)
          |  |  |        |  +--rw bandwidth-profile-name?   string
          |  |  |        +--:(value)
          |  |  |           +--rw bandwidth-profile-type?   etht-types:bandwidth-profile-type
          |  |  |           +--rw CIR?                      uint64
          |  |  |           +--rw CBS?                      uint64
          |  |  |           +--rw EIR?                      uint64
          |  |  |           +--rw EBS?                      uint64
          |  |  |           +--rw color-aware?              boolean
          |  |  |           +--rw coupling-flag?            boolean

Zheng, et al.            Expires April 25, 2019                 [Page 5]
Internet-Draft     Transport Client Signals YANG Model      October 2018

          |  |  +--:(asymmetrical)
          |  |     +--rw ingress-bandwidth-profile
          |  |     |  +--rw (style)?
          |  |     |     +--:(named)
          |  |     |     |  +--rw bandwidth-profile-name?   string
          |  |     |     +--:(value)
          |  |     |        +--rw bandwidth-profile-type?   etht-types:bandwidth-profile-type
          |  |     |        +--rw CIR?                      uint64
          |  |     |        +--rw CBS?                      uint64
          |  |     |        +--rw EIR?                      uint64
          |  |     |        +--rw EBS?                      uint64
          |  |     |        +--rw color-aware?              boolean
          |  |     |        +--rw coupling-flag?            boolean
          |  |     +--rw egress-bandwidth-profile
          |  |        +--rw (style)?
          |  |           +--:(named)
          |  |           |  +--rw bandwidth-profile-name?   string
          |  |           +--:(value)
          |  |              +--rw bandwidth-profile-type?   etht-types:bandwidth-profile-type
          |  |              +--rw CIR?                      uint64
          |  |              +--rw CBS?                      uint64
          |  |              +--rw EIR?                      uint64
          |  |              +--rw EBS?                      uint64
          |  |              +--rw color-aware?              boolean
          |  |              +--rw coupling-flag?            boolean
          |  +--rw vlan-operations
          |     +--rw (direction)?
          |        +--:(symmetrical)
          |        |  +--rw symmetrical-operation
          |        |     +--rw pop-tags?    uint8
          |        |     +--rw push-tags
          |        |        +--rw outer-tag!
          |        |        |  +--rw tag-type?      etht-types:eth-tag-type
          |        |        |  +--rw vlan-value?    etht-types:vlanid
          |        |        |  +--rw default-pcp?   uint8
          |        |        +--rw second-tag!
          |        |           +--rw tag-type?      etht-types:eth-tag-type
          |        |           +--rw vlan-value?    etht-types:vlanid
          |        |           +--rw default-pcp?   uint8
          |        +--:(asymmetrical)
          |           +--rw asymmetrical-operation
          |              +--rw ingress
          |              |  +--rw pop-tags?    uint8
          |              |  +--rw push-tags
          |              |     +--rw outer-tag!
          |              |     |  +--rw tag-type?      etht-types:eth-tag-type
          |              |     |  +--rw vlan-value?    etht-types:vlanid
          |              |     |  +--rw default-pcp?   uint8

Zheng, et al.            Expires April 25, 2019                 [Page 6]
Internet-Draft     Transport Client Signals YANG Model      October 2018

          |              |     +--rw second-tag!
          |              |        +--rw tag-type?      etht-types:eth-tag-type
          |              |        +--rw vlan-value?    etht-types:vlanid
          |              |        +--rw default-pcp?   uint8
          |              +--rw egress
          |                 +--rw pop-tags?    uint8
          |                 +--rw push-tags
          |                    +--rw outer-tag!
          |                    |  +--rw tag-type?      etht-types:eth-tag-type
          |                    |  +--rw vlan-value?    etht-types:vlanid
          |                    |  +--rw default-pcp?   uint8
          |                    +--rw second-tag!
          |                       +--rw tag-type?      etht-types:eth-tag-type
          |                       +--rw vlan-value?    etht-types:vlanid
          |                       +--rw default-pcp?   uint8
          +--rw etht-svc-tunnels* [tunnel-name]
          |  +--rw tunnel-name                string
          |  +--rw (svc-multiplexing-tag)?
          |  |  +--:(other)
          |  |  +--:(none)
          |  |  +--:(vlan-tag)
          |  |  +--:(pw)
          |  +--rw src-split-horizon-group?   string
          |  +--rw dst-split-horizon-group?   string
          +--rw pm-config
          |  +--rw pm-enable?             boolean
          |  +--rw sending-rate-high?     uint64
          |  +--rw sending-rate-low?      uint64
          |  +--rw receiving-rate-high?   uint64
          |  +--rw receiving-rate-low?    uint64
          +--rw admin-status?             identityref
          +--ro state
             +--ro operational-state?         identityref
             +--ro provisioning-state?        identityref
             +--ro creation-time?             yang:date-and-time
             +--ro last-updated-time?         yang:date-and-time
             +--ro sending-rate-too-high?     uint32
             +--ro sending-rate-too-low?      uint32
             +--ro receiving-rate-too-high?   uint32
             +--ro receiving-rate-too-low?    uint32

Zheng, et al.            Expires April 25, 2019                 [Page 7]
Internet-Draft     Transport Client Signals YANG Model      October 2018

4.2.  YANG Tree for other Transport Network Client Signal Model

   module: ietf-trans-client-service
       +--rw client-svc
          +--rw client-svc-instances* [client-svc-name]
             +--rw client-svc-name           string
             +--rw client-svc-descr?         string
             +--rw te-topology-identifier
             |  +--rw provider-id?   te-types:te-global-id
             |  +--rw client-id?     te-types:te-global-id
             |  +--rw topology-id?   te-types:te-topology-id
             +--rw src-access-ports
             |  +--rw access-node-id?   te-types:te-node-id
             |  +--rw access-ltp-id?    te-types:te-tp-id
             |  +--rw client-signal?    identityref
             +--rw dst-access-ports
             |  +--rw access-node-id?   te-types:te-node-id
             |  +--rw access-ltp-id?    te-types:te-tp-id
             |  +--rw client-signal?    identityref
             +--rw svc-tunnels* [tunnel-name]
             |  +--rw tunnel-name    string
             +--rw admin-status?             identityref
             +--ro operational-state?        identityref
             +--ro provisioning-state?       identityref

5.  YANG Code for Transport Network Client Signal

5.1.  The ETH Service YANG Code

<CODE BEGINS> file "ietf-eth-tran-service@2018-10-18.yang"

module ietf-eth-tran-service {

  namespace "urn:ietf:params:xml:ns:yang:ietf-eth-tran-service";

  prefix "ethtsvc";

  import ietf-yang-types {
    prefix "yang";
  }

  import ietf-te-types {
    prefix "te-types";

Zheng, et al.            Expires April 25, 2019                 [Page 8]
Internet-Draft     Transport Client Signals YANG Model      October 2018

  }

  import ietf-eth-tran-types {
    prefix "etht-types";
  }

  organization
    "Internet Engineering Task Force (IETF) CCAMP WG";
  contact
    "
      WG List: <mailto:ccamp@ietf.org>

      ID-draft editor:
        Haomian Zheng (zhenghaomian@huawei.com);
        Italo Busi (italo.busi@huawei.com);
        Aihua Guo (aihuaguo@huawei.com);
        Yunbin Xu (xuyunbin@ritt.cn);
        Yang Zhao (zhaoyangyjy@chinamobile.com);
        Xufeng Liu (Xufeng_Liu@jabil.com);
        Giuseppe Fioccola (giuseppe.fioccola@huawei.com);
    ";

  description
    "This module defines a YANG data model for describing
     the Ethernet transport services.";

  revision 2018-10-18 {
    description
      "Initial revision";
    reference
      "draft-zheng-ccamp-otn-client-signal-yang";
  }

  /*
   * Groupings
   */

  grouping vlan-classification {
    description
      "A grouping which represents classification on an 802.1Q VLAN tag.";

    leaf tag-type {
      type etht-types:eth-tag-classify;
      description
        "The tag type used for VLAN classification.";
    }
    choice individual-bundling-vlan {
      description

Zheng, et al.            Expires April 25, 2019                 [Page 9]
Internet-Draft     Transport Client Signals YANG Model      October 2018

        "VLAN based classification can be individual
         or bundling.";

      case individual-vlan {
        leaf vlan-value {
          type etht-types:vlanid;
          description
            "VLAN ID value.";
        }
      }

      case vlan-bundling {
        leaf vlan-range {
          type etht-types:vid-range-type;
          description
            "List of VLAN ID values.";
        }
      }
    }
  }

  grouping vlan-write {
    description
      "A grouping which represents push/pop operations
       of an 802.1Q VLAN tag.";

    leaf tag-type {
      type etht-types:eth-tag-type;
      description
        "The VLAN tag type to push/swap.";
    }
    leaf vlan-value {
      type etht-types:vlanid;
      description
        "The VLAN ID value to push/swap.";
    }
/*
 * To be added: this attribute is used when:
 * a) the ETH service has only one CoS (as in current version)
 * b) as a default when a mapping between a given CoS value
 *    and the PCP value is not defined (in future versions)
 */
    leaf default-pcp {
      type uint8 {
        range "0..7";
      }
      description
        "The default Priority Code Point (PCP) value to push/swap";

Zheng, et al.            Expires April 25, 2019                [Page 10]
Internet-Draft     Transport Client Signals YANG Model      October 2018

    }
  }

  grouping vlan-operations {
    description
      "A grouping which represents VLAN operations.";

      leaf pop-tags {
      type uint8 {
        range "1..2";
      }
      description
        "The number of VLAN tags to pop (or swap if used in
         conjunction with push-tags)";
    }
    container push-tags {
      description
        "The VLAN tags to push (or swap if used in
         conjunction with pop-tags)";

      container outer-tag {
        presence
          "Indicates existence of the outermost VLAN tag to
           push/swap";

        description
          "The outermost VLAN tag to push/swap.";

        uses vlan-write;
      }
      container second-tag {
        must
          '../outer-tag/tag-type = "etht-types:s-vlan-tag-type" and ' +
          'tag-type = "etht-types:c-vlan-tag-type"'
        {

          error-message
            "
              When pushing/swapping two tags, the outermost tag must
              be specified and of S-VLAN type and the second
              outermost tag must be of C-VLAN tag type.
            ";
          description
            "
              For IEEE 802.1Q interoperability, when pushing/swapping
              two tags, it is required that the outermost tag exists
              and is an S-VLAN, and the second outermost tag is a
              C-VLAN.

Zheng, et al.            Expires April 25, 2019                [Page 11]
Internet-Draft     Transport Client Signals YANG Model      October 2018

            ";
        }

        presence
          "Indicates existence of a second outermost VLAN tag to
           push/swap";

        description
          "The second outermost VLAN tag to push/swap.";

        uses vlan-write;
      }
    }
  }

  grouping named-or-value-bandwidth-profile {
    description
      "A grouping to configure a bandwdith profile either by
       referencing a named bandwidth profile or by
       configuring the values of the bandwidth profile attributes.";
    choice style {
      description
        "Whether the bandwidth profile is named or defined by value";

      case named {
        description
          "Named bandwidth profile.";
        leaf bandwidth-profile-name {
          type "string";
          description
            "Name of the bandwidth profile.";
        }
      }
      case value {
        description
          "Bandwidth profile configured by value.";
        uses etht-types:etht-bandwidth-profiles;
      }
    }
  }

  grouping bandwidth-profiles {
    description
      "A grouping which represent bandwidth profile configuration.";

    choice direction {
      description
        "Whether the bandwidth profiles are symmetrical or

Zheng, et al.            Expires April 25, 2019                [Page 12]
Internet-Draft     Transport Client Signals YANG Model      October 2018

         asymmetrical";
      case symmetrical {
        description
          "The same bandwidth profile is used to describe both
           the ingress and the egress bandwidth profile.";
        container ingress-egress-bandwidth-profile {
          description
            "The bandwdith profile used in both directions.";
          uses named-or-value-bandwidth-profile;
        }
      }
      case asymmetrical {
        description
          "Ingress and egress bandwidth profiles can be specified.";
        container ingress-bandwidth-profile {
          description
            "The bandwdith profile used in the ingress direction.";
          uses named-or-value-bandwidth-profile;
        }
        container egress-bandwidth-profile {
          description
            "The bandwdith profile used in the egress direction.";
          uses named-or-value-bandwidth-profile;
        }
      }
    }
  }

  grouping etht-svc-access-parameters {
    description
      "ETH transport services access parameters";

    leaf access-node-id {
      type te-types:te-node-id;
      description
        "The identifier of the access node in
         the ETH transport topology.";
    }
    leaf access-ltp-id {
      type te-types:te-tp-id;
      description
        "The TE link termination point identifier, used
         together with access-node-id to identify the
         access LTP.";
    }
    leaf service-classification-type {
      type identityref {
        base etht-types:service-classification-type;

Zheng, et al.            Expires April 25, 2019                [Page 13]
Internet-Draft     Transport Client Signals YANG Model      October 2018

      }
      description
        "Service classification type.";
    }

    choice service-classification {
      description
        "Access classification can be port-based or
         VLAN based.";

      case port-classification {
        /* no additional information */
      }

      case vlan-classification {
        container outer-tag {
          presence "The outermost VLAN tag exists";
          description
            "Classifies traffic using the outermost VLAN tag.";

          uses vlan-classification;
        }
        container second-tag {
          must
            '../outer-tag/tag-type = "etht-types:classify-s-vlan" and ' +
            'tag-type = "etht-types:classify-c-vlan"'
          {

            error-message
              "
                When matching two tags, the outermost tag must be
                specified and of S-VLAN type and the second
                outermost tag must be of C-VLAN tag type.
              ";
            description
              "
                For IEEE 802.1Q interoperability, when matching two
                tags, it is required that the outermost tag exists
                and is an S-VLAN, and the second outermost tag is a
                C-VLAN.
              ";
          }
          presence "The second outermost VLAN tag exists";

          description
            "Classifies traffic using the second outermost VLAN tag.";

          uses vlan-classification;

Zheng, et al.            Expires April 25, 2019                [Page 14]
Internet-Draft     Transport Client Signals YANG Model      October 2018

        }
      }
    }

/*
 * Open issue: can we constraints it to be used only with mp services?
 */
    leaf split-horizon-group {
      type string;
      description "Identify a split horizon group";
    }

    uses bandwidth-profiles;

    container vlan-operations {
      description
        "Configuration of VLAN operations.";
      choice direction {
        description
          "Whether the VLAN operations are symmetrical or
           asymmetrical";
        case symmetrical {
          container symmetrical-operation {
            uses vlan-operations;
            description
              "Symmetrical operations.
               Expressed in the ingress direction, but
               the reverse operation is applied to egress traffic";
          }
        }
        case asymmetrical {
          container asymmetrical-operation {
            description "Asymmetrical operations";
            container ingress {
              uses vlan-operations;
              description "Ingress operations";
            }
            container egress {
              uses vlan-operations;
              description "Egress operations";
            }
          }
        }
      }
    }
  }

  grouping etht-svc-tunnel-parameters {

Zheng, et al.            Expires April 25, 2019                [Page 15]
Internet-Draft     Transport Client Signals YANG Model      October 2018

    description
      "ETH transport services tunnel parameters";

    leaf tunnel-name {
      type string;
      description
        "TE service tunnel instance name.";
    }
    choice svc-multiplexing-tag {
      description
        "Service multiplexing is optional and flexible.";

      case other {
        /*
         placeholder to support proprietary multiplexing
         (for further discussion)
        */
      }

      case none {
        /* no additional information is needed */
      }

      case vlan-tag {
        /*
          No additional information is needed
          The C-Tag or S-Tag used for service mulitplexing is defined
          by the VLAN classification and operations configured in the
          etht-svc-access-parameters grouping
        */
      }

      case pw {
        /* to be completed (for further discussion) */
      }
    }

/*
 * Open issue: can we constraints it to be used only with mp services?
 */
    leaf src-split-horizon-group {
      type string;
      description "Identify a split horizon group at the Tunnel source TTP";
    }
    leaf dst-split-horizon-group {
      type string;
      description "Identify a split horizon group at the Tunnel destination TTP";
    }

Zheng, et al.            Expires April 25, 2019                [Page 16]
Internet-Draft     Transport Client Signals YANG Model      October 2018

  }

  grouping  etht-svc-pm-threshold_config {
    description
      "Configuraiton parameters for Ethernet service PM thresholds.";

    leaf sending-rate-high {
      type uint64;
      description
        "High threshold of packet sending rate in kbps.";
    }
    leaf sending-rate-low {
      type uint64;
      description
        "Low threshold of packet sending rate in kbps.";
    }
    leaf receiving-rate-high {
      type uint64;
      description
        "High threshold of packet receiving rate in kbps.";
    }
    leaf receiving-rate-low {
      type uint64;
      description
        "Low threshold of packet receiving rate in kbps.";
    }
  }

  grouping  etht-svc-pm-stats {
    description
      "Ethernet service PM statistics.";

    leaf sending-rate-too-high {
      type uint32;
      description
        "Counter that indicates the number of times the sending rate is above the high threshold";
    }
    leaf sending-rate-too-low {
      type uint32;
      description
        "Counter that indicates the number of times the sending rate is below the low threshold";
    }
    leaf receiving-rate-too-high {
      type uint32;
      description
        "Counter that indicates the number of times the receiving rate is above the high threshold";
    }
    leaf receiving-rate-too-low {

Zheng, et al.            Expires April 25, 2019                [Page 17]
Internet-Draft     Transport Client Signals YANG Model      October 2018

      type uint32;
      description
        "Counter that indicates the number of times the receiving rate is below the low threshold";
    }
  }

  grouping  etht-svc-instance_config {
    description
      "Configuraiton parameters for Ethernet services.";

    leaf etht-svc-name {
      type string;
      description
        "Name of the ETH transport service.";
    }

    leaf etht-svc-id {
      type yang:uuid;
      description
        "Universally Unique IDentifier (UUID) of the ETH transport service.";
    }

    leaf etht-svc-descr {
      type string;
      description
        "Description of the ETH transport service.";
    }

    leaf etht-svc-customer {
      type string;
      description
        "Customer of the ETH transport service.";
    }

     leaf etht-svc-type {
      type etht-types:service-type;
      description
        "Type of ETH transport service (p2p, mp2mp or rmp).";
      /* Add default as p2p */
    }

     leaf etht-svc-lifecycle {
      type etht-types:lifecycle-status;
      description
        "Lifecycle state of ETH transport service.";
      /* Add default as installed  */
    }

Zheng, et al.            Expires April 25, 2019                [Page 18]
Internet-Draft     Transport Client Signals YANG Model      October 2018

    uses te-types:te-topology-identifier;

    list etht-svc-access-ports {
      key access-port-id;
      min-elements "1";
/*
  Open Issue:
    Is it possible to limit the max-elements only for p2p services?

      max-elements "2";
*/
      description
        "List of the ETH trasport services access port instances.";

      leaf access-port-id {
        type uint16;
        description
          "ID of the service access port instance";
      }
        uses etht-svc-access-parameters;
    }
    list etht-svc-tunnels {
      key tunnel-name;
      description
        "List of the TE Tunnels supporting the ETH
        transport service.";

      uses etht-svc-tunnel-parameters;
    }
    container pm-config {
      description
        "ETH service performance monitoring";

      leaf pm-enable {
        type boolean;
        description
          "Boolean value indicating whether PM is enabled.";
      }
      uses etht-svc-pm-threshold_config;
    }
    leaf admin-status {
      type identityref {
        base te-types:tunnel-state-type;
      }
      default te-types:tunnel-state-up;
      description "ETH service administrative state.";
    }
  }

Zheng, et al.            Expires April 25, 2019                [Page 19]
Internet-Draft     Transport Client Signals YANG Model      October 2018

  grouping  etht-svc-instance_state {
    description
      "State parameters for Ethernet services.";

    leaf operational-state {
    type identityref {
        base te-types:tunnel-state-type;
      }
      default te-types:tunnel-state-up;
    description "ETH service operational state.";
    }
    leaf provisioning-state {
      type identityref {
        base te-types:lsp-state-type;
      }
      description "ETH service provisioning state.";
    }
    leaf creation-time {
      type yang:date-and-time;
      description
        "Time of ETH service creation.";
    }
    leaf last-updated-time {
      type yang:date-and-time;
      description
        "Time of ETH service last update.";
    }
    uses etht-svc-pm-stats;
  }

  /*
   * Data nodes
   */

  container etht-svc {
    description
      "ETH transport services.";

    container globals {
      description
        "Globals Ethernet configuration data container";
      list named-bandwidth-profiles {
        key bandwidth-profile-name;
        description
          "List of named bandwidth profiles used by
           Ethernet services.";

        leaf bandwidth-profile-name {

Zheng, et al.            Expires April 25, 2019                [Page 20]
Internet-Draft     Transport Client Signals YANG Model      October 2018

          type string;
          description
            "Name of the bandwidth profile.";
        }
        uses etht-types:etht-bandwidth-profiles;
      }
    }

    list etht-svc-instances {
      key etht-svc-name;
      description
        "The list of p2p ETH transport service instances";

      uses etht-svc-instance_config;

      container state {
        config false;
        description
          "Ethernet Service states.";

        uses etht-svc-instance_state;
      }
    }
  }
}

<CODE ENDS>

5.2.  YANG Code for ETH transport type

<CODE BEGINS> file "ietf-eth-tran-types@2018-10-18.yang"
module ietf-eth-tran-types {

  namespace "urn:ietf:params:xml:ns:yang:ietf-eth-tran-types";

  prefix "etht-types";

  organization
    "Internet Engineering Task Force (IETF) CCAMP WG";
  contact
    "
      WG List: <mailto:ccamp@ietf.org>

      ID-draft editor:
        Haomian Zheng (zhenghaomian@huawei.com);

Zheng, et al.            Expires April 25, 2019                [Page 21]
Internet-Draft     Transport Client Signals YANG Model      October 2018

        Italo Busi (italo.busi@huawei.com);
        Aihua Guo (aihuaguo@huawei.com);
        Yunbin Xu (xuyunbin@ritt.cn);
        Yang Zhao (zhaoyangyjy@chinamobile.com);
        Xufeng Liu (Xufeng_Liu@jabil.com);
        Giuseppe Fioccola (giuseppe.fioccola@huawei.com);
    ";

  description
    "This module defines the ETH transport types.";

  revision 2018-10-18 {
    description
      "Initial Revision";
    reference
      "draft-zheng-ccamp-client-signal-yang";
  }

  /*
   * Identities
   */

  identity eth-vlan-tag-type {
    description
      "ETH VLAN tag type.";
  }

  identity c-vlan-tag-type {
    base eth-vlan-tag-type;
    description
      "802.1Q Customer VLAN";
  }

  identity s-vlan-tag-type {
    base eth-vlan-tag-type;
    description
      "802.1Q Service VLAN (QinQ)";
  }

  identity service-classification-type {
    description
      "Service classification.";
  }

  identity port-classification {
    base service-classification-type;
    description
      "Port classification.";

Zheng, et al.            Expires April 25, 2019                [Page 22]
Internet-Draft     Transport Client Signals YANG Model      October 2018

  }

  identity vlan-classification {
    base service-classification-type;
    description
      "VLAN classification.";
  }

  identity eth-vlan-tag-classify {
    description
      "VLAN tag classification.";
  }

  identity classify-c-vlan {
    base eth-vlan-tag-classify;
    description
      "Classify 802.1Q Customer VLAN tag.
       Only C-tag type is accepted";
  }

  identity classify-s-vlan {
    base eth-vlan-tag-classify;
    description
      "Classify 802.1Q Service VLAN (QinQ) tag.
       Only S-tag type is accepted";
  }

  identity classify-s-or-c-vlan {
    base eth-vlan-tag-classify;
    description
      "Classify S-VLAN or C-VLAN tag-classify.
       Either tag is accepted";
  }

  identity bandwidth-profile-type {
    description
      "Bandwidth Profile Types";
  }

  identity mef-10-bwp {
    base bandwidth-profile-type;
    description
      "MEF 10 Bandwidth Profile";
  }

  identity rfc-2697-bwp {
    base bandwidth-profile-type;
    description

Zheng, et al.            Expires April 25, 2019                [Page 23]
Internet-Draft     Transport Client Signals YANG Model      October 2018

      "RFC 2697 Bandwidth Profile";
  }

  identity rfc-2698-bwp {
    base bandwidth-profile-type;
    description
      "RFC 2698 Bandwidth Profile";
  }

  identity rfc-4115-bwp {
    base bandwidth-profile-type;
    description
      "RFC 4115 Bandwidth Profile";
  }

  identity service-type {
    description
      "Type of Ethernet service.";
  }

  identity p2p-svc {
    base service-type;
    description
      "Ethernet point-to-point service (EPL, EVPL).";
  }

  identity rmp-svc {
    base service-type;
    description
      "Ethernet rooted-multitpoint service (E-TREE, EP-TREE).";
  }

  identity mp2mp-svc {
    base service-type;
    description
      "Ethernet multipoint-to-multitpoint service (E-LAN, EP-LAN).";
  }

  identity lifecycle-status {
    description
      "Lifecycle Status.";
  }

  identity installed {
    base lifecycle-status;
    description
      "Installed.";
  }

Zheng, et al.            Expires April 25, 2019                [Page 24]
Internet-Draft     Transport Client Signals YANG Model      October 2018

  identity planned {
    base lifecycle-status;
    description
      "Planned.";
  }

  identity pending-removal {
    base lifecycle-status;
    description
      "Pending Removal.";
  }

  /*
   * Type Definitions
   */

  typedef eth-tag-type {
    type identityref {
      base eth-vlan-tag-type;
    }
    description
      "Identifies a specific ETH VLAN tag type.";
  }

  typedef eth-tag-classify {
    type identityref {
      base eth-vlan-tag-classify;
    }
    description
      "Identifies a specific VLAN tag classification.";
  }

  typedef vlanid {
    type uint16 {
      range "1..4094";
    }
    description
      "The 12-bit VLAN-ID used in the VLAN Tag header.";
  }

  typedef vid-range-type {
    type string {
      pattern "([1-9][0-9]{0,3}(-[1-9][0-9]{0,3})?" +
              "(,[1-9][0-9]{0,3}(-[1-9][0-9]{0,3})?)*)";
    }
    description
      "A list of VLAN Ids, or non overlapping VLAN ranges, in
       ascending order, between 1 and 4094.

Zheng, et al.            Expires April 25, 2019                [Page 25]
Internet-Draft     Transport Client Signals YANG Model      October 2018

       This type is used to match an ordered list of VLAN Ids, or
       contiguous ranges of VLAN Ids. Valid VLAN Ids must be in the
       range 1 to 4094, and included in the list in non overlapping
       ascending order.

       For example: 1,10-100,50,500-1000";
  }

  typedef bandwidth-profile-type {
    type identityref {
      base bandwidth-profile-type;
    }
    description
      "Identifies a specific Bandwidth Profile type.";
  }

  typedef service-type {
    type identityref {
      base service-type;
    }
    description
      "Identifies the type of Ethernet service.";
  }

  typedef lifecycle-status {
    type identityref {
      base lifecycle-status;
    }
    description
      "Identifies the lLifecycle Status .";
  }

  /*
   * Grouping Definitions
   */

  grouping etht-bandwidth-profiles {
    description
      "Bandwidth profile configuration paramters.";

    leaf bandwidth-profile-type {
      type etht-types:bandwidth-profile-type;
      description
        "The type of bandwidth profile.";
    }
    leaf CIR {
      type uint64;
      description

Zheng, et al.            Expires April 25, 2019                [Page 26]
Internet-Draft     Transport Client Signals YANG Model      October 2018

        "Committed Information Rate in Kbps";
    }
    leaf CBS {
      type uint64;
      description
        "Committed Burst Size in in KBytes";
    }
    leaf EIR {
      type uint64;
      /* Need to indicate that EIR is not supported by RFC 2697

      must
        '../bw-profile-type = "mef-10-bwp" or ' +
        '../bw-profile-type = "rfc-2698-bwp" or ' +
        '../bw-profile-type = "rfc-4115-bwp"'

      must
        '../bw-profile-type != "rfc-2697-bwp"'
      */
      description
        "Excess Information Rate in Kbps
         In case of RFC 2698, PIR = CIR + EIR";
    }
    leaf EBS {
      type uint64;
      description
        "Excess Burst Size in KBytes.
          In case of RFC 2698, PBS = CBS + EBS";
    }
    leaf color-aware {
      type boolean;
      description
        "Indicates weather the color-mode is color-aware or color-blind.";
    }
    leaf coupling-flag {
      type boolean;
      /* Need to indicate that Coupling Flag is defined only for MEF 10

      must
        '../bw-profile-type = "mef-10-bwp"'
      */
      description
        "Coupling Flag.";
    }
  }
}

Zheng, et al.            Expires April 25, 2019                [Page 27]
Internet-Draft     Transport Client Signals YANG Model      October 2018

<CODE ENDS>

5.3.  Other Transport Network client signal YANG Code

 <CODE BEGINS> file "ietf-trans-client-service@2018-10-19.yang"
 module ietf-trans-client-service {
   /* TODO: FIXME */
   //yang-version 1.1;

   namespace "urn:ietf:params:xml:ns:yang:ietf-trans-client-service";
   prefix "clntsvc";

   import ietf-te-types {
     prefix "te-types";
   }

   import ietf-l1-service-types {
     prefix "l1-svc-types";
   }

   organization
     "Internet Engineering Task Force (IETF) CCAMP WG";
   contact
     "

       ID-draft editor:
         Aihua Guo (aihuaguo@huawei.com);
         Haomian Zheng (zhenghaomian@huawei.com);
         Italo Busi (italo.busi@huawei.com);
         Yunbin Xu (xuyunbin@ritt.cn);
         Yang Zhao (zhaoyangyjy@chinamobile.com);
         Xufeng Liu (Xufeng_Liu@jabil.com);
         Giuseppe Fioccola (giuseppe.fioccola@telecomitalia.it);
     ";

   description
     "This module defines a YANG data model for describing
      simple transport client services.";

   revision 2018-10-19 {
     description
       "Initial version";
     reference
       "draft-zheng-ccamp-client-signal-yang";
   }

Zheng, et al.            Expires April 25, 2019                [Page 28]
Internet-Draft     Transport Client Signals YANG Model      October 2018

   /*
    * Groupings
    */

   grouping client-svc-access-parameters {
     description
       "Transport client services access parameters";

     leaf access-node-id {
       type te-types:te-node-id;
       description
         "The identifier of the access node in the underlying
          transport topology.";
     }
     leaf access-ltp-id {
       type te-types:te-tp-id;
       description
         "The TE link termination point identifier, used together with
          access-node-id to identify the access LTP.";
     }
     leaf client-signal {
       type identityref {
         base l1-svc-types:protocol-type;
       }
       description
         "Identifiies the client signal type associated with this port";
     }
   }

   grouping client-svc-tunnel-parameters {
     description
       "Transport client services tunnel parameters";

     leaf tunnel-name {
       type string;
       description
         "TE service tunnel instance name.";
     }
   }

   grouping  client-svc-instance_config {
     description
       "Configuraiton parameters for client services.";

     leaf client-svc-name {
       type string;
       description
         "Name of the p2p transport client service.";

Zheng, et al.            Expires April 25, 2019                [Page 29]
Internet-Draft     Transport Client Signals YANG Model      October 2018

     }
     leaf client-svc-descr {
       type string;
       description
         "Description of the transport client service.";
     }
     uses te-types:te-topology-identifier;
     container src-access-ports {
       description
         "Source access port of a client service.";
       uses client-svc-access-parameters;
     }
     container dst-access-ports {
       description
         "Destination access port of a client service.";
       uses client-svc-access-parameters;
     }
     list svc-tunnels {
       key tunnel-name;
       description
         "List of the TE Tunnels supporting the client service.";
       uses client-svc-tunnel-parameters;
     }
     leaf admin-status {
       type identityref {
         base te-types:tunnel-state-type;
       }
       default te-types:tunnel-state-up;
       description "Client service administrative state.";
     }
   }

   grouping  client-svc-instance_state {
         description
           "State parameters for client services.";
         leaf operational-state {
           type identityref {
                 base te-types:tunnel-state-type;
           }
           config false;
           description "Client service operational state.";
         }
         leaf provisioning-state {
           type identityref {
                 base te-types:lsp-state-type;
           }
           config false;
           description "Client service provisioning state.";

Zheng, et al.            Expires April 25, 2019                [Page 30]
Internet-Draft     Transport Client Signals YANG Model      October 2018

         }
   }

   /*
    * Data nodes
    */

   container client-svc {
     description
       "Transport client services.";

     list client-svc-instances {
       key client-svc-name;
       description
         "The list of p2p transport client service instances";

           uses client-svc-instance_config;
           uses client-svc-instance_state;
     }
   }
 }

 <CODE ENDS>

6.  Considerations and Open Issue

   Editor Notes: This section is used to note temporary discussion/
   conclusion that to be fixed in the future version, and will be
   removed before publication.  We currently categorize all the client
   signal types into transparent and non-transparent, with separate
   models.  There was consensus that no common model is needed for these
   two categories.

7.  IANA Considerations

   TBD.

8.  Manageability Considerations

   TBD.

9.  Security Considerations

   The data following the model defined in this document is exchanged
   via, for example, the interface between an orchestrator and a
   transport network controller.  The security concerns mentioned in

Zheng, et al.            Expires April 25, 2019                [Page 31]
Internet-Draft     Transport Client Signals YANG Model      October 2018

   [I-D.ietf-teas-yang-te-topo] for using ietf-te-topology.yang model
   also applies to this document.

   The YANG module defined in this document can be accessed via the
   RESTCONF protocol defined in [RFC8040], or maybe via the NETCONF
   protocol [RFC6241].

   There are a number of data nodes defined in the YANG module which are
   writable/creatable/deletable (i.e., config true, which is the
   default).  These data nodes may be considered sensitive or vulnerable
   in some network environments.  Write operations (e.g., POST) to these
   data nodes without proper protection can have a negative effect on
   network operations.

10.  Acknowledgements

   We would like to thank Igor Bryskin and Daniel King for their
   comments and discussions.

11.  Contributors

   Yanlei Zheng
   China Unicom
   Email: zhengyl@dimpt.com

   Zhe Liu
   Huawei Technologies,
   Email: liuzhe123@huawei.com

   Sergio Belotti
   Nokia,
   Email: sergio.belotti@nokia.com

   Yingxi Yao
   Shanghai Bell,
   yingxi.yao@nokia-sbell.com

12.  References

12.1.  Normative References

   [I-D.ietf-ccamp-otn-topo-yang]
              Zheng, H., Guo, A., Busi, I., Sharma, A., Liu, X.,
              Belotti, S., Xu, Y., Wang, L., and O. Dios, "A YANG Data
              Model for Optical Transport Network Topology", draft-ietf-
              ccamp-otn-topo-yang-05 (work in progress), August 2018.

Zheng, et al.            Expires April 25, 2019                [Page 32]
Internet-Draft     Transport Client Signals YANG Model      October 2018

   [I-D.ietf-ccamp-otn-tunnel-model]
              Zheng, H., Guo, A., Busi, I., Sharma, A., Rao, R.,
              Belotti, S., Lopezalvarez, V., Li, Y., and Y. Xu, "OTN
              Tunnel YANG Model", draft-ietf-ccamp-otn-tunnel-model-05
              (work in progress), August 2018.

   [I-D.ietf-teas-yang-te-topo]
              Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H., and
              O. Dios, "YANG Data Model for Traffic Engineering (TE)
              Topologies", draft-ietf-teas-yang-te-topo-18 (work in
              progress), June 2018.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.

   [RFC7139]  Zhang, F., Ed., Zhang, G., Belotti, S., Ceccarelli, D.,
              and K. Pithewan, "GMPLS Signaling Extensions for Control
              of Evolving G.709 Optical Transport Networks", RFC 7139,
              DOI 10.17487/RFC7139, March 2014,
              <https://www.rfc-editor.org/info/rfc7139>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/info/rfc7950>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

12.2.  Informative References

   [I-D.ietf-netmod-yang-tree-diagrams]
              Bjorklund, M. and L. Berger, "YANG Tree Diagrams", draft-
              ietf-netmod-yang-tree-diagrams-06 (work in progress),
              February 2018.

   [I-D.zhang-teas-transport-service-model]
              Zhang, X. and J. Ryoo, "A Service YANG Model for
              Connection-oriented Transport Networks", draft-zhang-teas-
              transport-service-model-01 (work in progress), October
              2016.

Zheng, et al.            Expires April 25, 2019                [Page 33]
Internet-Draft     Transport Client Signals YANG Model      October 2018

   [RFC7062]  Zhang, F., Ed., Li, D., Li, H., Belotti, S., and D.
              Ceccarelli, "Framework for GMPLS and PCE Control of G.709
              Optical Transport Networks", RFC 7062,
              DOI 10.17487/RFC7062, November 2013,
              <https://www.rfc-editor.org/info/rfc7062>.

Authors' Addresses

   Haomian Zheng
   Huawei Technologies
   H1-1-A043S Huawei Industrial Base, Songshanhu
   Dongguan, Guangdong
   P.R.China

   Email: zhenghaomian@huawei.com

   Aihua Guo
   Huawei Technologies

   Email: aihuaguo@huawei.com

   Italo Busi
   Huawei Technologies

   Email: Italo.Busi@huawei.com

   Yunbin Xu
   CAICT

   Email: xuyunbin@ritt.cn

   Yang Zhao
   China Mobile

   Email: zhaoyangyjy@chinamobile.com

   Xufeng Liu
   Volta Networks

   Email: xufeng.liu.ietf@gmail.com

Zheng, et al.            Expires April 25, 2019                [Page 34]
Internet-Draft     Transport Client Signals YANG Model      October 2018

   Giuseppe Fioccola
   Huawei Technology

   Email: giuseppe.fioccola@huawei.com

Zheng, et al.            Expires April 25, 2019                [Page 35]