Networking Working Group                                    R. Alexander
Internet-Draft                                                   T. Tsao
Intended status: Standards Track                    Cooper Power Systems
Expires: January 8, 2012                                    July 7, 2011


Adapted Multimedia Internet KEYing (AMIKEY): An extension of Multimedia
      Internet KEYing (MIKEY) Methods for Generic LLN Environments
               draft-alexander-roll-mikey-lln-key-mgmt-00

Abstract

   Multimedia Internet Keying (MIKEY) is a key management protocol used
   for real-time applications.  As standardized within RFC3830 it
   defines four key distribution methods, including pre-shared keys,
   public-key encryption, and Diffie-Hellman key exchange, with
   allowances for ready protocol extension.  A number of additional
   methods have been developed and continue to be built from the base
   protocol (see for example, RFC4442, RFC4563, RFC4650, RFC4738,
   RFC5410, RFC6043 and RFC6267.  However, in spite of its extensibility
   and more general applicability, MIKEY and its related extensions have
   primarily focused on the support of the Secure Real-time Transport
   Protocol (SRTP).

   This document specifies a simple adaptation of the MIKEY
   specification to allow the base protocol and its various key
   management mode extensions to be readily applied in more general
   environments beyond the multimedia SRTP domain.  In particular, the
   document defines a repurposing of the MIKEY multimedia crypto
   sessions structure and introduces a set of message extensions to the
   base specification to allow the MIKEY key management methods to be
   applied within Low-power and Lossy networks (LLNs) and other general
   constrained-device networks.

Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in RFC
   2119 [RFC2119].

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute



Alexander & Tsao         Expires January 8, 2012                [Page 1]


Internet-Draft           MIKEY Extension for LLN               July 2011


   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on January 8, 2012.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.



























Alexander & Tsao         Expires January 8, 2012                [Page 2]


Internet-Draft           MIKEY Extension for LLN               July 2011


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  5
     1.1.  Motivation . . . . . . . . . . . . . . . . . . . . . . . .  5
     1.2.  MIKEY Key Management Methods Background  . . . . . . . . .  6
     1.3.  Adapting MIKEY to General LLNs . . . . . . . . . . . . . .  7
     1.4.  Terminology and Definitions  . . . . . . . . . . . . . . .  7
     1.5.  Document Outline . . . . . . . . . . . . . . . . . . . . .  9
     1.6.  Section Headings Notation  . . . . . . . . . . . . . . . .  9
   2.  AMIKEY Overview  . . . . . . . . . . . . . . . . . . . . . . . 10
   3.  AMIKEY Extension Elements  . . . . . . . . . . . . . . . . . . 12
     3.1.  [RFC3830] Pre-shared key . . . . . . . . . . . . . . . . . 12
     3.2.  [RFC3830] Public-Key Encryption  . . . . . . . . . . . . . 12
     3.3.  [RFC3830] Diffie-Hellman Key Exchange  . . . . . . . . . . 12
   4.  [RFC3830] Selected Key Management Functions  . . . . . . . . . 12
     4.1.  [RFC3830] Key Calculation  . . . . . . . . . . . . . . . . 12
       4.1.1.  [RFC3830] Assumptions  . . . . . . . . . . . . . . . . 12
       4.1.2.  [RFC3830] Default PRF Description  . . . . . . . . . . 13
       4.1.3.  [RFC3830] Generating Keys from TGK . . . . . . . . . . 13
       4.1.4.  [RFC3830] Generating Keys for MIKEY Messages from
               an Envelope/Pre-shared Key . . . . . . . . . . . . . . 13
     4.2.  [RFC3830] Pre-defined Transforms and Timestamp Formats . . 13
       4.2.1.  [RFC3830] Hash Functions . . . . . . . . . . . . . . . 13
       4.2.2.  [RFC3830] Pseudo-Random Number Generator . . . . . . . 13
       4.2.3.  [RFC3830] Key Data Transport Encryption  . . . . . . . 13
       4.2.4.  [RFC3830] MAC Verification Message Function  . . . . . 13
     4.3.  [RFC3830] Certificates, Policies and Authorization . . . . 14
     4.4.  [RFC3830] Retrieving the Data SA . . . . . . . . . . . . . 14
   5.  [RFC3830] Behavior and Message Handling  . . . . . . . . . . . 14
   6.  [RFC3830] Payload Encoding . . . . . . . . . . . . . . . . . . 14
     6.1.  [RFC3830] Common Header Payload (HDR)  . . . . . . . . . . 14
       6.1.1.  [RFC3830] SRTP ID  . . . . . . . . . . . . . . . . . . 17
       6.1.2.  The Generic_LLN-ID Map Type  . . . . . . . . . . . . . 17
     6.2.  [RFC3830] Key Data Transport Payload (KEMAC) . . . . . . . 19
     6.3.  [RFC3830] Envelope Data Payload (PKE)  . . . . . . . . . . 19
     6.4.  [RFC3830] DH Data Payload (DH) . . . . . . . . . . . . . . 19
     6.5.  [RFC3830] Signature Payload (SIGN) . . . . . . . . . . . . 19
     6.6.  [RFC3830] Timestamp Payload (T)  . . . . . . . . . . . . . 19
     6.7.  [RFC3830] ID Payload (ID)  . . . . . . . . . . . . . . . . 20
     6.8.  [RFC3830] Cert Hash Payload (CHASH)  . . . . . . . . . . . 20
     6.9.  [RFC3830] Ver msg payload (V)  . . . . . . . . . . . . . . 20
     6.10. [RFC3830] Security Policy (SP) Payload . . . . . . . . . . 20
       6.10.1. [RFC3830] SRTP Policy  . . . . . . . . . . . . . . . . 21
       6.10.2. AMIKEY Generic_LLN Policy  . . . . . . . . . . . . . . 21
     6.11. [RFC3830] RAND Payload (RAND)  . . . . . . . . . . . . . . 23
     6.12. [RFC3830] Error Payload (ERR)  . . . . . . . . . . . . . . 23
     6.13. [RFC3830] Key Data Sub-Payload . . . . . . . . . . . . . . 23
     6.14. [RFC3830] Key Validity Data  . . . . . . . . . . . . . . . 23



Alexander & Tsao         Expires January 8, 2012                [Page 3]


Internet-Draft           MIKEY Extension for LLN               July 2011


     6.15. [RFC3830] General Extension Payload  . . . . . . . . . . . 23
     6.16. Key Index Payload  . . . . . . . . . . . . . . . . . . . . 23
     6.17. Key Activation Time Payload  . . . . . . . . . . . . . . . 23
   7.  [RFC3830] Transport Protocols  . . . . . . . . . . . . . . . . 24
   8.  Security Considerations  . . . . . . . . . . . . . . . . . . . 24
   9.  [RFC3830] Groups . . . . . . . . . . . . . . . . . . . . . . . 24
   10. Additional Specification Considerations  . . . . . . . . . . . 24
   11. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 25
   12. Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 26
   13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 26
     13.1. Normative References . . . . . . . . . . . . . . . . . . . 26
     13.2. Informative References . . . . . . . . . . . . . . . . . . 26
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 28






































Alexander & Tsao         Expires January 8, 2012                [Page 4]


Internet-Draft           MIKEY Extension for LLN               July 2011


1.  Introduction

   Any sufficiently large scale network offering security services
   requires an automated key management mechanism for the exchange of
   keys and the update of related security credentials [RFC4107].  Key
   management may be needed for individual session exchanges or for the
   long-term control and update of security parameters from which
   session keys may be derived.  In many Low-power and Lossy networks
   (LLN) and other constrained-device environments, key management
   emphasis is often on the management of long-term keys.  This may
   automatically follow network associations based on device pre-
   configuration or may be based on specified key lifetimes or
   administrative or event-driven need for key credential changes.  This
   would apply to the case of a network routing protocol like RPL
   ([I-D.ietf-roll-rpl]) that employs security as well as to other
   secured communications layer protocols.

   Multimedia Internet Keying (MIKEY) is a key management protocol that
   has been used for real-time applications both for peer-to-peer and
   group communications.  The capabilities of the protocol lend
   themselves just as readily to the management of long-term keys as to
   per-session or per association key control.  MIKEY [RFC3830] defines
   four key distribution methods including pre-shared keys, public-key
   encryption, and Diffie-Hellman key exchange.  Given its design
   simplicity, efficiency and flexibility a number of additional modes
   and extensions have indeed been developed and continue to be built
   from the base protocol (see for example, [RFC4442], [RFC4563],
   [RFC4650], [RFC4738], [RFC5410], [RFC6043] and [RFC6267]).  MIKEY and
   its related RFC extensions have however primarily focused on the
   support of the SRTP and related Session Initiation Protocol (SIP)
   call scenarios [RFC3711].

   This document specifies an adaptation of the MIKEY protocol
   specification to allow the base protocol and its various key
   management mode extensions to be more generally applied to LLN
   environments.  In particular, the document defines a repurposing of
   the MIKEY multimedia crypto sessions structure to allow optional
   support for simultaneous management of multiple protocol or device
   interface key.  The specification also introduces a set of message
   extensions to the base MIKEY protocol to allow its key management
   methods to be applied within generic LLN and constrained-device
   networks.

1.1.  Motivation

   Key distribution describes the process of delivering cryptographic
   keys to the required communicating parties.  The MIKEY protocol has
   defined the mechanisms for establishing the security context used by



Alexander & Tsao         Expires January 8, 2012                [Page 5]


Internet-Draft           MIKEY Extension for LLN               July 2011


   SRTP however the mechanisms for security parameter negotiation and
   update is just as readily extended to LLN protocols.

   The flexibly to employ different key distribution methods according
   to available network infrastructure and particular operating
   scenarios together with the compact efficiency of its binary
   specification makes MIKEY well suited for general LLN use.  The wide
   range of key management support extending from light-weight, low
   latency half round-trip pre-shared key distribution methods to multi-
   exchange Diffie-Hellman key agreements protected with digital
   signatures or pre-shared keys offers great flexibility to meet the
   needs of diverse LLN application environments.

   The option to embed the MIKEY key management messages within an
   existing network signaling protocol or to be directly transported or
   UDP or TCP (using port 2269) also increases the ability to apply the
   methods in more general LLN domains.

   MIKEY has met its original stated design goals [RFC3830] of end-to-
   end security, simplicity, efficiency, tunneling (even beyond
   integration with Session Description Protocol (SDP) [RFC4566] or RTCP
   [RFC3605]), and independence of underlying transport.  In so doing it
   offers an excellent base for a generic key management protocol for
   Low-power Lossy Network (LLN) application.  Key management protocols
   are also difficult to design and validate (see [RFC4107] guidelines)
   providing a further motivation for reliance on an established
   protocol like MIKEY that has had the benefit of wider operational
   deployment and evaluation.

1.2.  MIKEY Key Management Methods Background

   As noted in [RFC5197], several key distribution methods have been
   described for MIKEY, including:

   o  Symmetric key distribution as defined in [RFC3830] (MIKEY-PSK)

   o  Asymmetric key distribution as defined in [RFC3830] (MIKEY-RSA)

   o  Diffie-Hellman key agreement protected by digital signatures as
      defined in [RFC3830] (MIKEY-DHSIGN)

   o  Diffie-Hellman key agreement protected by symmetric pre-shared
      keys as defined in [RFC4650] (MIKEY-DHHMAC)

   o  Asymmetric key distribution (based on asymmetric encryption) with
      in-band certificate provision as defined in [RFC4738]
      (MIKEY-RSA-R)




Alexander & Tsao         Expires January 8, 2012                [Page 6]


Internet-Draft           MIKEY Extension for LLN               July 2011


   Further extensions to MIKEY comprising algorithm enhancements and new
   payload definitions have since been defined generally motivated by
   the specific problems associated with SIP signaling and associated
   multimedia use case scenarios (see [RFC5197]for an earlier
   assessment).  This specification proposes a new extension that is
   focused on a new domain of application.

1.3.  Adapting MIKEY to General LLNs

   This document specifies is a set of additional message information
   elements to the base MIKEY protocol that provide both algorithm and
   message payload extensions.  These additions allow the adapted
   protocol to be used directly for key transport and security policy
   specification between communications generic network entities.
   Furthermore, through integration within the base MIKEY specification
   it will allow current and future key methods and extensions to be
   utilized outside of the current multimedia environment.

   The developed protocol adaption includes the specification of
   alternative default algorithms (in particular AES-based) and
   configurations that are particular to more constrained communications
   devices and using MIKEY's general extensibility to define new
   elements applicable to the LLN environment.

   An important element of the protocol extension is the re-use of the
   MIKEY crypto-session structure to apply to individual device
   communications protocol layers or interfaces instead of applying to
   multimedia streams.  By maintaining this base protocol structure and
   re-purposing associated message identifiers, the specification
   minimizes the protocol changes needed for network adaptation.

   As with the original specification the intent is to allow MIKEY
   messages to be embedded into existing communications signaling
   protocols or to be independently transported between communicating
   entities over UDP or TCP transport connections.

   Note: While MIKEY and its extensions provide a variety of choices in
   terms of modes of operation, implementations for a given LLN
   application domain will be able to simplify node behavior by
   operating in a single mode.  To ensure necessary interoperability
   within the LLN environment, mandatory methods within the Adapted
   MIKEY protocol (AMIKEY), akin to those of MIKEY, shall be specified.

1.4.  Terminology and Definitions

   The following definitions have been taken from [RFC3830] with
   necessary augmentation for AMIKEY as indicated:




Alexander & Tsao         Expires January 8, 2012                [Page 7]


Internet-Draft           MIKEY Extension for LLN               July 2011


   (Data) Security Protocol
         The security protocol used to protect the actual data traffic.
         Examples of security protocols are IPsec and SRTP.  For generic
         LLNs, security protocols may include secure versions of
         protocols such as RPL [I-D.ietf-roll-rpl].

   Data SA
         Data Security Association information for the security
         protocol, including a TEK and a set of parameters/policies.

   CS    Crypto Session, uni- or bidirectional data stream(s) protected
         by a single instance of a security protocol.  For AMIKEY the
         concept of a crypto-session is expanded to allow definition of
         a particular protocol layer, logical device interface, or other
         communications association for which key management support is
         provided.

   CSB   Crypto Session Bundle, collection of one or more Crypto
         Sessions, which can have common TGKs (see below) and security
         parameters.

   CS ID Crypto Session ID, unique identifier for the CS within a CSB.
         For AMIKEY the CS ID is used to identify a specific protocol
         layer, logical device interface or other communications
         association for which AMIKEY is being used to support key
         management (establishment of re-keying update).

   CSB ID
         Crypto Session Bundle ID, unique identifier for the CSB.  For
         AMIKEY the CSB ID in conjunction with the Timestamp filed is
         used as a unique key management exchange message reference
         identifier.  This identifier will allow for the acknowledged
         key management message exchanges where applicable.  The ID plus
         timestamp will also support the filtering of repeated or
         redundant AMIKEY messages when key management occurs over an
         unreliable transport network.

   TGK   TEK Generation Key, a bit-string agreed upon by two or more
         parties, associated with CSB.  From the TGK, Traffic-Encrypting
         Keys can then be generated without needing further
         communication.

   TEK   Traffic-Encrypting Key, the key used by the security protocol
         to protect the CS (this key may be used directly by the
         security protocol or may be used to derive further keys
         depending on the security protocol).  The TEKs are derived from
         the CSB's TGK.




Alexander & Tsao         Expires January 8, 2012                [Page 8]


Internet-Draft           MIKEY Extension for LLN               July 2011


   The following definitions have been added to the ones from [RFC3830]
   specifically related to supporting AMIKEY:

   Key Index
         The Key Index (KI) is used as identifier to allow for reference
         to the key(s) that are associated with a given CS.  Where TEKs
         may be updated over time a TGK can be associated with a KI that
         is transported as a payload within the AMIKEY message from the
         Initiator.  Any TEK generated from the AMIKEY TGK shall be
         assigned the key index value associated with the TGK.  Within
         general LLN protocol communications related to a given CS
         (device layer protocol or interface), to ensure security
         association synchronization reference can be made to the key
         index that is being applied for the given protocol security.
         Following successfully TGK key establishment communicating
         devices can verify security contexts through reference to
         maintained KI.

1.5.  Document Outline

   Section 2 provides a brief general system overview of key management
   as introduced in MIKEY specification.  This section generalizes the
   context in which the Adapted MIKEY (AMIKEY) protocol extension is
   applied.  It also provides a reference to the common key management
   operating base of MIKEY and AMIKEY.

   Sections 3 to 4 go into further detail by identifying the specific
   section and subsection extensions and enhancements needed to support
   the MIKEY protocol adaptation.  These Sections mirror those of MIKEY
   [RFC3830] and are used to show the necessary commonality and make
   reference to specific changes would be required for AMIKEY.
   Reference is made only to the applicable Sections and Subsections of
   [RFC3830] for which special changes are proposed.

   Section 6 includes the specific protocol specification elements that
   are needed to extend MIKEY for the support of the generic LLN key
   management requirements.

   The remaining document sections are place-holders for standard RFC
   draft sections.

1.6.  Section Headings Notation

   This document is written as a delta document to [RFC3830].  For ease
   of cross-reference and to maintain consistency with the MIKEY
   specification document structure, Section heading and Table and
   Figure numbers are maintained consistent with the [RFC3830] usage.




Alexander & Tsao         Expires January 8, 2012                [Page 9]


Internet-Draft           MIKEY Extension for LLN               July 2011


   The notation of Section number followed by [RFC3830] "x.x.
   [RFC3830]" is used is this document for Sections specifically meant
   to align with [RFC3830].  Section numbers followed by [RFC3830] with
   additional heading text indicates some new element or clarification
   introduced by this specification.  Section numbers followed by
   [RFC3830] without further heading text implies no change to [RFC3830]
   and is used only to align and maintain the current document headings
   structure.


2.  AMIKEY Overview

   This section provides an overview of AMIKEY.  Material from MIKEY
   [RFC3830] is also repeated to clearly establish the common context in
   which MIKEY can be applied to LLN environments with the simple
   extension to the Adapted MIKEY (AMIKEY) specification.

   The objective of the AMIKEY extension is exactly the same as that of
   MIKEY - "to produce a data security association (SA) for a security
   protocol, including a Traffic-Encrypting Key (TEK), which is derived
   from a TEK Generation Key (TGK), and used as input for the security
   protocol."  In the case of AMIKEY the objective is support generic
   security protocols and particularly those that may be associated with
   LLNs.

   AMIKEY uses the specified MIKEY mechanisms and features to "support
   the possibility of establishing keys and parameters for more than one
   security protocol (or for several instances of the same security
   protocol) at the same time."  In MIKEY the Crypto Session Bundle
   (CSB), which derives from the multimedia (multi-stream) context, is
   used to denote this collection of one or more Crypto Sessions that
   can have a common TGK and security parameters, but that obtain
   distinct TEKs from MIKEY.

   In the AMIKEY extension, the concept of CSB is used to provide the
   option of simultaneously establishing multiple SAs on a given device.
   The individual Crypto Session (CS) SAs may be associated with
   different device layer or device interface security protocols.
   AMIKEY further uses the flexibility of the MIKEY specification to
   allow separate security policies to be defined in the SA established
   for each security protocol.  The distribution mechanisms defined by
   MIKEY for re-keying and updating of established security associations
   is hence also directly applied.  The ability to establish and
   maintain multiple SAs through a single key management association
   provides an important efficiency element in LLN domains.

   As specified in [RFC3830], Section 2.3, the procedure of setting up a
   CSB and creating a TEK (and Data SA), is done in accordance with



Alexander & Tsao         Expires January 8, 2012               [Page 10]


Internet-Draft           MIKEY Extension for LLN               July 2011


   Figure 1:

   1.  A set of security parameters and TGK(s) are agreed upon for the
       Crypto Session Bundle.  This is done by one of many alternative
       key transport/exchange mechanisms (see [RFC3830], Section 3, as
       well as subsequent extension RFCs).

   2.  The TGK(s) is used to derive (in a cryptographically secure way)
       a TEK for each Crypto Session or associated security protocol.

   3.  The TEK, together with the security protocol parameters,
       represent the Data SA, which is used as the input to the security
       protocol(s).



           +-----------------+
           |       CSB       |
           |  Key transport  | (see [RFC3830], Section 3)
           |    /exchange    |
           +-----------------+
                    |      :
                    | TGK  :
                    v      :
              +----------+ :
      CS ID ->|   TEK    | : Security protocol parameters (policies)
              |derivation| : (see [RFC3830], Section 4)
              +----------+ :
                 TEK |     :
                     v     v
                     Data SA
                       |
                       v
              +-------------------+
              |  Crypto Session   |
              |(Security Protocol)|
              +-------------------+


     Figure 1: Overview of MIKEY (and AMIKEY extension) key management
                                 procedure

   For generic LLNs that are the focus of this document, the default
   algorithms applied in the generation of the TEK for each protocol is
   defined within this AMIKEY specification.  An additional MIKEY
   message extension is also specified to define the security protocol
   parameters (policies) for generic LLNs.




Alexander & Tsao         Expires January 8, 2012               [Page 11]


Internet-Draft           MIKEY Extension for LLN               July 2011


   Whereas MIKEY CS IDs are associated with multimedia streams and have
   no intrinsic designation, in this specification the CS IDs are
   assigned values (public or private/vendor-specific) that are used to
   identify security protocols associated with specific device protocol
   layers or device interfaces.

   As in the base MIKEY specification, the security protocol can either
   use the TEK directly, or, if supported, derive further session keys
   from the TEK (e.g., see SRTP [RFC3711]).  It is however up to the
   targeted security protocol and the associated security policy to
   define how the TEK is used.

   MIKEY can be used to update TEKs and the Crypto Sessions in a current
   Crypto Session Bundle (see [RFC3830], Section 4.5).  This is done by
   executing the transport/exchange phase once again to obtain a new TGK
   (and consequently derive new TEKs) or to update some other specific
   CS parameters.


3.  AMIKEY Extension Elements

   The following Section and Subsections detail the proposed additions
   to the MIKEY specification [RFC3830] to support the AMIKEY extension.
   The Section heading outline of the MIKEY specification is used to
   indicate the delta changes made by the AMIKEY extension.

3.1.  [RFC3830] Pre-shared key

3.2.  [RFC3830] Public-Key Encryption

3.3.  [RFC3830] Diffie-Hellman Key Exchange


4.  [RFC3830] Selected Key Management Functions

   For AMIKEY all the key derivation functionality defined in MIKEY
   shall be based on a new default Pseudo-Random Function (PRF) given by
   the AES-based, AES-XCBC-PRF-128 algorithm as specified in [RFC4434].

4.1.  [RFC3830] Key Calculation

4.1.1.  [RFC3830] Assumptions

   For AMIKEY cs_id is defined so that session represents a protocol
   layer, logical device interface, or communications association.  The
   cs-id values shall be as defined in this specification (see
   Section 6.1.2) and may be public or private/vendor-specific.




Alexander & Tsao         Expires January 8, 2012               [Page 12]


Internet-Draft           MIKEY Extension for LLN               July 2011


4.1.2.  [RFC3830] Default PRF Description

   For AMIKEY the default pseudo random function shall be AES-XCBC-PRF-
   128 [RFC4434].  Note: AES-XCBC-PRF-128 aligns with HMAC-SHA1 and
   HMAC-MD5 as PRFs.

4.1.3.  [RFC3830] Generating Keys from TGK

   For AMIKEY the cs-id values shall be as defined in this specification
   (see Section 6.1.2).

4.1.4.  [RFC3830] Generating Keys for MIKEY Messages from an Envelope/
        Pre-shared Key

   Change from default PRF to the default AMIKEY PRF given in
   Section 4.1.2 of this specification.

   Note: For AMIKEY, the Authentication key constant SHALL be used for
   generating the single TEK in the case of authenticated encryption
   algorithms (such as AES-CCM).

4.2.  [RFC3830] Pre-defined Transforms and Timestamp Formats

4.2.1.  [RFC3830] Hash Functions

   For AMIKEY the default hash function shall be AES-XCBC-PRF-128
   [RFC4434].

4.2.2.  [RFC3830] Pseudo-Random Number Generator

   For AMIKEY it shall be MANDATORY to implement the new default AES-
   XCBC-PRF-128 PRF specified in [RFC4434] (See Section 4.1.2 of this
   specification).

4.2.3.  [RFC3830] Key Data Transport Encryption

   As in MIKEY the default and mandatory-to-implement key transport
   encryption shall be AES in Counter mode using a 128-bit key (derived
   as defined in Section 4.1.4 above).  The applied Counter shall be the
   IV defined in [RFC3830], Section 4.2.3.

4.2.4.  [RFC3830] MAC Verification Message Function

   For AMIKEY AES-CCM-64 shall be the defined default for key message
   authentication.  The Counter used shall be the IV defined in
   [RFC3830], Section 4.2.3.





Alexander & Tsao         Expires January 8, 2012               [Page 13]


Internet-Draft           MIKEY Extension for LLN               July 2011


4.3.  [RFC3830] Certificates, Policies and Authorization

4.4.  [RFC3830] Retrieving the Data SA

   For AMIKEY the retrieval of a Data SA will depend on the security
   protocol.  The support for different security protocols shall be
   explicitly identified through the use of public CS ID values (see
   Section 6.1.2 of this specification).


5.  [RFC3830] Behavior and Message Handling


6.  [RFC3830] Payload Encoding

   The generic LLN security protocol parameters may be transported
   between peers as part of a key establishment or re-keying exchange.
   Based on IANA registration, MIKEY currently only defines two payloads
   for transporting the security policy information (see Section 6.10 of
   [RFC3830] and [RFC4442]).  This section describes the extension of
   MIKEY to allow the transport of Generic LLN security policy
   information and associated key(s) as well as applicable PRF used for
   key derivation.

   This section describes, in detail, the payload for support of the
   Generic LLN security protocol(s) specified by the Adapted MIKEY
   protocol.  As in RFC3830, for all encoding, network byte order is
   always used, and the sign ~ indicates a variable length field.

6.1.  [RFC3830] Common Header Payload (HDR)

   The Common Header payload MUST always be present as the first payload
   in each message.  The Common Header includes a general description of
   the exchange message.

















Alexander & Tsao         Expires January 8, 2012               [Page 14]


Internet-Draft           MIKEY Extension for LLN               July 2011


                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !  version      !  data type    ! next payload  !V! PRF func    !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                         CSB ID                                !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! #CS           ! CS ID map type! CS ID map info                ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                     Figure 2: Common Header [RFC3830]

   o  version (8 bits): the version number of MIKEY.

   o  version = 0x01 refers to MIKEY as defined and maintained in
      [RFC3830].

   o  version = 0x0n (to be assigned) shall be used to refer to AMIKEY
      as defined and maintained in this document.

   o  data type (8 bits): describes the type of message (e.g., public-
      key transport message, verification message, error message).  See
      latest IANA registered values.  No additional values are specified
      for AMIKEY (TBD).

   o  next payload (8 bits): identifies the payload that is added after
      this payload.  See latest IANA registered values.

   For AMIKEY a new next payload value is assigned to carry the Key
   Index parameter (see also Section 6.16).

   +---------+-------+-------------------------------------------------+
   | Next    | Value | Section                                         |
   | Payload |       |                                                 |
   +---------+-------+-------------------------------------------------+
   | Last    |   0   | -                                               |
   | payload |       |                                                 |
   | ...     |       |                                                 |
   | Key     |   n   | Section 6.16 as given by the AMIKEY             |
   | Index   |       | specification (value to be assigned by IANA).   |
   | Key act |   m   | Section 6.17 as given by the AMIKEY             |
   | time    |       | specification (value to be assigned by IANA)    |
   +---------+-------+-------------------------------------------------+

                                Table 6.1.b





Alexander & Tsao         Expires January 8, 2012               [Page 15]


Internet-Draft           MIKEY Extension for LLN               July 2011


   o  V (1 bit): flag to indicate whether a verification message is
      expected or not (this only has meaning when it is set by the
      Initiator).

   o  PRF func (7 bits): indicates the PRF function that has been/will
      be used for key derivation; for AMIKEY a new value, 2, has been
      specified to indicate the PRF that must be supported for LLNs.

   +------------------+-------+----------------------------------------+
   | PRF Function     | Value | Comments                               |
   +------------------+-------+----------------------------------------+
   | AES-XCBC-PRF-128 |   2   | As specified in [RFC4434] and that     |
   |                  |       | shall be mandatory for AMIKEY          |
   +------------------+-------+----------------------------------------+

                                Table 6.1.c

   (AMIKEY value to be assigned by IANA)

   o  CSB ID (32 bits): identifies the CSB (generated as specified in
      [RFC3830]); for AMIKEY this field is used as a message reference
      identifier to allow for duplicate detection where message
      exchanges occur over an unreliable transport network.

   o  #CS (8 bits): indicates the number of Crypto Sessions that will be
      handled within the CBS; for AMIKEY this field indicates the number
      of protocol layers, logical device interfaces, or other
      communications associations that are being configured or managed
      within the current key management message exchange.

   o  CS ID map type (8 bits): specifies the method of uniquely mapping.
      Crypto Sessions to the security protocol sessions; for AMIKEY a
      new value, 3, has been specified to indicate the Generic-LLN map
      type that must be supported for LLNs.

   +----------------+-------+------------------------------------------+
   | CS ID Map Type | Value | Comments                                 |
   +----------------+-------+------------------------------------------+
   | Generic_LLN-ID |   3   | As specified in this document and as     |
   |                |       | mandatory for AMIKEY                     |
   +----------------+-------+------------------------------------------+

                                Table 6.1.d

   (AMIKEY value to be assigned by IANA)






Alexander & Tsao         Expires January 8, 2012               [Page 16]


Internet-Draft           MIKEY Extension for LLN               July 2011


   o  CS ID map info (variable length): identifies the crypto session(s)
      for which the SA should be created.  For AMIKEY the GENERIC_LLN
      map type (defined in Section 6.1.2 below) is used to specify the
      security association for the individual protocol layers, logical
      device interfaces, or other communications associations for which
      key management is being provided.

6.1.1.  [RFC3830] SRTP ID

6.1.2.  The Generic_LLN-ID Map Type

   For the Generic_LLN map type, the CS ID map info consists of #CS (see
   Section 6.1) number of blocks or segments, where each segment maps
   policies (and a key) to a specific protocol layer, logical device
   interface or other communications association security protocol.



       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !     CS ID     !       #P      !          Ps (OPTIONAL)        ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                     Figure 3: Generic_LLN-ID Map Type

   o  CS ID (8 bits): specifies the CS ID used to identify a given
      security protocol; for AMIKEY, when used in conjunction with the
      Generic-LLN map type, values 0-127 shall be reserved for
      assignment (by IANA) to specific protocol layer, logical device
      interface, or other communications association security protocols
      while values 128-255 shall be Reserved for Private Use.

   Note: A combination of public and private CS IDs can be specified
   within a given CSB when combined key management is being applied.

   The following values are currently specified in this document (for
   example, with values to be assigned by IANA):












Alexander & Tsao         Expires January 8, 2012               [Page 17]


Internet-Draft           MIKEY Extension for LLN               July 2011


    +---------------------------+---------+--------------------------+
    | CS ID                     |  Value  | Comments                 |
    +---------------------------+---------+--------------------------+
    | Reserved                  |    0    |                          |
    | Generic PHY Layer         |    1    |                          |
    | Generic Link Layer        |    2    |                          |
    | Generic Network Layer     |    3    |                          |
    | Generic Application Layer |    7    |                          |
    | RPL Protocol              |    20   |                          |
    | ...                       |         |                          |
    | Reserved values           | 128-255 | Reserved for private use |
    +---------------------------+---------+--------------------------+

                                Table 6.1.e

   o  #P (8 bits): indicates the number of security policies provided
      for the crypto session (given by the CS ID) for which key
      management is being provided.  In response messages, #P SHALL
      always be exactly 1.  So if #P = 0 in an initial message, a
      security profile MUST be provided in the response message.  If #P
      > 0, one of the suggested policies SHOULD be chosen in the
      response message.  If needed, the suggested policies MAY be
      changed.

   o  Ps (variable length): lists the policies for the crypto session
      for which key management is being provided.  It SHALL contain
      exactly #P policies, each having the specified Prot type (see
      Section 6.10.



        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    !  Policy_no_i  !  Policy_no_n  !      ...      ! Policy_no_#P  !
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                            Figure 4: Policies

   o  Policy_no_i (8 bits): a policy_no that corresponds to the
      policy_no of a SP payload.  In response messages, the policy_no
      may refer to a SP payload in the initial message.  The policy
      numbers should be listed in increasing order.







Alexander & Tsao         Expires January 8, 2012               [Page 18]


Internet-Draft           MIKEY Extension for LLN               July 2011


6.2.  [RFC3830] Key Data Transport Payload (KEMAC)

   This section shall apply entirely as specified for MIKEY in [RFC3830]
   with the addition of the specific message authentication code
   algorithms given below for AMIKEY.

   o  MAC alg (8 bits): specifies the authentication algorithm used.

   +------------------+-------+----------------------------+-----------+
   | MAC alg          | Value | Comments                   |   Length  |
   |                  |       |                            |   (bits)  |
   +------------------+-------+----------------------------+-----------+
   | NULL             |   0   | restricted usage           |     0     |
   |                  |       | [RFC3830], Section 4.2.4   |           |
   | HMAC-SHA-1-160   |   1   | Mandatory, [RFC3830],      |    160    |
   |                  |       | Section 4.2.4              |           |
   | HMAC-SHA-256-256 |   2   | Mandatory, [RFC3830],      |    256    |
   |                  |       | Section 4.2.4              |           |
   | AES-CBC-MAC-32   |   3   | Mandatory for AMIKEY, see  |     32    |
   |                  |       | Section 4.2.4              |           |
   | AES-CBC-MAC-64   |   4   | Mandatory for AMIKEY, see  |     64    |
   |                  |       | Section 4.2.4              |           |
   | AES-CBC-MAC-128  |   5   | Mandatory for AMIKEY, see  |    128    |
   |                  |       | Section 4.2.4              |           |
   +------------------+-------+----------------------------+-----------+

                                Table 6.2.b

   (Values for AMIKEY to be assigned by IANA)

   o  MAC (variable length): the message authentication code of the
      entire message.

   For AMIKEY the use of AES-CBC-MAC-n may be applied in conjunction
   with the AES-CM encryption as given by the Encr alg field.  This
   authenticated encryption shall be applied using an AES-CCM-n
   implementation.

6.3.  [RFC3830] Envelope Data Payload (PKE)

6.4.  [RFC3830] DH Data Payload (DH)

6.5.  [RFC3830] Signature Payload (SIGN)

6.6.  [RFC3830] Timestamp Payload (T)






Alexander & Tsao         Expires January 8, 2012               [Page 19]


Internet-Draft           MIKEY Extension for LLN               July 2011


6.7.  [RFC3830] ID Payload (ID)

   For AMIKEY the range of ID types shall be extended to allow for an
   expanded array of communications protocol entities that may be key
   management participants.

            +--------------+-------+-------------------------+
            | ID Type      | Value | Comments                |
            +--------------+-------+-------------------------+
            | IPv6 Address |   4   | As specified for AMIKEY |
            | Other (TBD)  |   n   | As specified for AMIKEY |
            +--------------+-------+-------------------------+

                                Table 6.7.a

6.8.  [RFC3830] Cert Hash Payload (CHASH)

6.9.  [RFC3830] Ver msg payload (V)

6.10.  [RFC3830] Security Policy (SP) Payload

   The Security Policy payload defines a set of policies that apply to a
   specific security protocol.

   For AMIKEY the definition is based on the same security policy
   payload definition in [RFC3830], Section 6.10, with a new security
   protocol (Generic-LLN) as defined below.



       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Next payload  ! Policy no     ! Prot type     ! Policy param  ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ~ length (cont) ! Policy param                                  ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   o  Next payload (8 bits): Identifies the payload that is added after
      this payload.  See Section 6.1 of [RFC3830] for more details.

   o  Policy no (8 bits): Each security policy payload must be given a
      distinct number for the current MIKEY session by the local peer.
      This number is used to map a cryptographic session to a specific
      policy (see also Section 6.1.1 of [RFC3830]).





Alexander & Tsao         Expires January 8, 2012               [Page 20]


Internet-Draft           MIKEY Extension for LLN               July 2011


   o  Prot type (8 bits): This value defines the security protocol; For
      AMIKEY an additional value shall be assigned as given below.

            +-------------+-------+---------------------------+
            | Prot Type   | Value |          Comments         |
            +-------------+-------+---------------------------+
            | Generic_LLN |   2   | (As specified for AMIKEY) |
            +-------------+-------+---------------------------+

                                Table 6.10

   o  Policy param length (16 bits): This field defines the total length
      of the policy parameters for the selected security protocol.

   o  Policy param (variable length): This field defines the policy for
      the specific security protocol.  The Policy param part is built up
      by a set of Type/Length/Value (TLV) payloads.  For each security
      protocol, a set of possible type/value pairs can be negotiated as
      defined.



       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Type          ! Length        ! Value                         ~
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



                        Figure 5: Policy Parameter

   o  Type (8 bits): Specifies the type of the parameter.

   o  Length (8 bits): Specifies the length of the Value field (in
      bytes).

   o  Value (variable length): Specifies the value of the parameter.

6.10.1.  [RFC3830] SRTP Policy

6.10.2.  AMIKEY Generic_LLN Policy

   This policy specifies the parameters for the Generic_LLN (G_LLN)
   protocol for which key management is being provided.  The types/
   values that can be negotiated are defined by the following table for
   the known, assigned CS ID values.  For Vendor-specific, private CS ID
   values the applicable policy specification for a given crypto session



Alexander & Tsao         Expires January 8, 2012               [Page 21]


Internet-Draft           MIKEY Extension for LLN               July 2011


   will be left to the communicating parties.

       +------+---------------------------+------------------------+
       | Type | Meaning                   | Possible Values        |
       +------+---------------------------+------------------------+
       |   0  | Encryption algorithm      | See below              |
       |   1  | Encryption key length     | Depends on cipher used |
       |   2  | Authentication algorithm  | See below              |
       |   3  | Authentication key length | Depends on MAC used    |
       |   4  | Generic LLN PRF           | See below              |
       |   5  | Encryption off/on         | 0 if off, 1 if on      |
       +------+---------------------------+------------------------+

                              Table 6.10.2.a

   For the Encryption algorithm, a one byte length is sufficient.  For
   AMIKEY the currently defined possible Values are:

                        +----------------+-------+
                        | G_LLN encr alg | Value |
                        +----------------+-------+
                        | NULL           |   0   |
                        | AES-CM         |   1   |
                        +----------------+-------+

                              Table 6.10.2.b

   For the Authentication algorithm, a one byte length is sufficient.
   For AMIKEY the currently defined possible Values are:

     +-----------------+-------+-------------------------------------+
     | G_LLN auth alg  | Value | Comments                            |
     +-----------------+-------+-------------------------------------+
     | NULL            |   0   | Not recommended for operational use |
     | AES-CBC-MAC-32  |   1   |                                     |
     | AES-CBC-MAC-64  |   2   |                                     |
     | AES-CBC-MAC-128 |   3   |                                     |
     +-----------------+-------+-------------------------------------+

                              Table 6.10.2.c

   Note: Since authentication is mandatory for operational protocol
   security, where Encryption is set "on" by the Generic_LLN policy,
   authenticated encryption, AES-CCM-n, with the MAC size given by the
   selected authentication algorithm shall be applied.

   For the Generic_LLN pseudo-random function, a one byte length is also
   sufficient.  For AMIKEY the currently defined possible Values are:



Alexander & Tsao         Expires January 8, 2012               [Page 22]


Internet-Draft           MIKEY Extension for LLN               July 2011


                       +------------------+-------+
                       | Generic_LLN PRF  | Value |
                       +------------------+-------+
                       | AES-XCBC-PRF-128 |   0   |
                       +------------------+-------+

                              Table 6.10.2.d

6.11.  [RFC3830] RAND Payload (RAND)

6.12.  [RFC3830] Error Payload (ERR)

6.13.  [RFC3830] Key Data Sub-Payload

6.14.  [RFC3830] Key Validity Data

6.15.  [RFC3830] General Extension Payload

6.16.  Key Index Payload

   For AMIKEY the Key Index payload is used to specify the value of the
   key index associated with a given TGK.



                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !  Next Payload !    KI value   !           Reserved            !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                            Figure 6: Key Index

   o  Next payload (8 bits): identifies the payload that is added after
      this payload.  See Section 6.1 [RFC3830] for values.

   o  KI value (8 bits): indicates the value (from 0-255) of the key
      index to be assigned to any CS TEK generated from the transported
      TGK.

6.17.  Key Activation Time Payload

   For AMIKEY the Key Activation time payload is used to specify the
   time at which a new key derived from a communicated TGK shall become
   active for the associated device protocol or interface.  The format
   of this AMIKEY information element type shall be the same as that of
   the Timestamp payload (T) [RFC3830].



Alexander & Tsao         Expires January 8, 2012               [Page 23]


Internet-Draft           MIKEY Extension for LLN               July 2011


                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !  Next Payload !     TS type   !    TS value                   !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



                   Figure 7: Key Activation Time Payload

   o  Next payload (8 bits): identifies the payload that is added after
      this payload.  See Section 6.1 [RFC3830] for values.

   o  TS type (8 bits): indicates the timestamp type use to convey the
      time at which a new derived TEK shall become active (See Section
      6.6 [RFC3830]).

   o  TS value (variable length): the timestamp value of the specified
      TS type (See Section 6.6 [RFC3830]).  Note: A TS value of 0 shall
      indicate that the applicable key update takes effect immediately.


7.  [RFC3830] Transport Protocols

   As in [RFC3830], AMIKEY may be integrated within session
   establishment or other system signaling protocols or may be directly
   transported over UDP or TCP.  Where AMIKEY messages are integrated
   into other LLN-related signaling protocols its transport shall be
   defined as part of those protocols.


8.  Security Considerations

   A primary motivation for this RFC is the security that comes from a
   re-use of the key management methods and framework developed for
   MIKEY.  The extensive deployment and on-going development provides
   the benefit of much wider vetting and validation essential to
   assuring greater security.


9.  [RFC3830] Groups


10.  Additional Specification Considerations

   Work had been previously initiated in developing support for an ECC-
   based asymmetric key management method ([I-D.ietf-msec-mikey-ecc],
   expired).  In the context of LLNs application and subject to IPR



Alexander & Tsao         Expires January 8, 2012               [Page 24]


Internet-Draft           MIKEY Extension for LLN               July 2011


   considerations, related AMIKEY requirements may be developed.


11.  IANA Considerations

   This document defines several new name spaces associated with the
   AMIKEY payloads.  This section summarizes the name spaces for which
   IANA is requested to manage the allocation of values.  IANA is
   requested to record the pre-defined values defined in the given
   sections for each name space.  IANA is also requested to manage the
   definition of additional values in the future.  Unless explicitly
   stated otherwise, values in the range 0-240 for each name space
   SHOULD be approved by the process of IETF consensus and values in the
   range 241-255 are reserved for Private Use, according to [RFC2434].

   The name spaces for the new fields identified in this document are
   requested to be managed by IANA (in bracket is the reference to the
   table with the initially registered values):

   o  Next payload (6.1.b)

      *  Key index

      *  Key activation time

   o  Prf func (6.1.c)

      *  AES-XCBC-PRF-128

   o  CS ID map type (6.1.d)

      *  Generic_LLN-ID

   o  MAC alg (6.2.b)

      *  AES-CBC-MAC-32

      *  AES-CBC-MAC-64

      *  AES-CBC-MAC-128

   o  ID payload (6.7.a)

      *  IPv6 Address

   o  Proto type (6.10)





Alexander & Tsao         Expires January 8, 2012               [Page 25]


Internet-Draft           MIKEY Extension for LLN               July 2011


      *  Generic_LLN

   o  Generic_LLN policy (6.10.2)

      *  Policy parameters (6.10.2.a)

      *  G_LLN encr alg (6.10.2.b)

      *  G_LLN auth alg (6.10.2.c)

      *  G_LLN prf (6.10.2.d)


12.  Acknowledgments

   The authors would like to acknowledge the review and comments from
   Rene Struik.


13.  References

13.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2434]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 2434,
              October 1998.

   [RFC3830]  Arkko, J., Carrara, E., Lindholm, F., Naslund, M., and K.
              Norrman, "MIKEY: Multimedia Internet KEYing", RFC 3830,
              August 2004.

   [RFC4434]  Hoffman, P., "The AES-XCBC-PRF-128 Algorithm for the
              Internet Key Exchange Protocol (IKE)", RFC 4434,
              February 2006.

13.2.  Informative References

   [I-D.ietf-msec-mikey-ecc]
              Milne, A., "ECC Algorithms for MIKEY",
              draft-ietf-msec-mikey-ecc-03 (work in progress),
              June 2007.

   [I-D.ietf-roll-rpl]
              Winter, T., Thubert, P., Brandt, A., Clausen, T., Hui, J.,
              Kelsey, R., Levis, P., Pister, K., Struik, R., and J.



Alexander & Tsao         Expires January 8, 2012               [Page 26]


Internet-Draft           MIKEY Extension for LLN               July 2011


              Vasseur, "RPL: IPv6 Routing Protocol for Low power and
              Lossy Networks", draft-ietf-roll-rpl-19 (work in
              progress), March 2011.

   [RFC3605]  Huitema, C., "Real Time Control Protocol (RTCP) attribute
              in Session Description Protocol (SDP)", RFC 3605,
              October 2003.

   [RFC3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
              Norrman, "The Secure Real-time Transport Protocol (SRTP)",
              RFC 3711, March 2004.

   [RFC4107]  Bellovin, S. and R. Housley, "Guidelines for Cryptographic
              Key Management", BCP 107, RFC 4107, June 2005.

   [RFC4442]  Fries, S. and H. Tschofenig, "Bootstrapping Timed
              Efficient Stream Loss-Tolerant Authentication (TESLA)",
              RFC 4442, March 2006.

   [RFC4563]  Carrara, E., Lehtovirta, V., and K. Norrman, "The Key ID
              Information Type for the General Extension Payload in
              Multimedia Internet KEYing (MIKEY)", RFC 4563, June 2006.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, July 2006.

   [RFC4650]  Euchner, M., "HMAC-Authenticated Diffie-Hellman for
              Multimedia Internet KEYing (MIKEY)", RFC 4650,
              September 2006.

   [RFC4738]  Ignjatic, D., Dondeti, L., Audet, F., and P. Lin, "MIKEY-
              RSA-R: An Additional Mode of Key Distribution in
              Multimedia Internet KEYing (MIKEY)", RFC 4738,
              November 2006.

   [RFC5197]  Fries, S. and D. Ignjatic, "On the Applicability of
              Various Multimedia Internet KEYing (MIKEY) Modes and
              Extensions", RFC 5197, June 2008.

   [RFC5410]  Jerichow, A. and L. Piron, "Multimedia Internet KEYing
              (MIKEY) General Extension Payload for Open Mobile Alliance
              BCAST 1.0", RFC 5410, January 2009.

   [RFC6043]  Mattsson, J. and T. Tian, "MIKEY-TICKET: Ticket-Based
              Modes of Key Distribution in Multimedia Internet KEYing
              (MIKEY)", RFC 6043, March 2011.

   [RFC6267]  Cakulev, V. and G. Sundaram, "MIKEY-IBAKE: Identity-Based



Alexander & Tsao         Expires January 8, 2012               [Page 27]


Internet-Draft           MIKEY Extension for LLN               July 2011


              Authenticated Key Exchange (IBAKE) Mode of", RFC 6267,
              June 2011.


Authors' Addresses

   Roger K. Alexander
   Cooper Power Systems
   20201 Century Blvd. Suite 250
   Germantown, Maryland  20874
   USA

   Email: roger.alexander@cooperindustries.com


   Tzeta Tsao
   Cooper Power Systems
   20201 Century Blvd. Suite 250
   Germantown, Maryland  20874
   USA

   Email: tzeta.tsao@cooperindustries.com





























Alexander & Tsao         Expires January 8, 2012               [Page 28]