Network Working Group M. Boucadair, Ed.
Internet-Draft P. Levis
Intended status: Informational France Telecom
Expires: January 4, 2010 G. Bajko
T. Savolainen
Nokia
July 3, 2009
IPv4 Connectivity Access in the Context of IPv4 Address Exhaustion: Port
Range based IP Architecture
draft-boucadair-port-range-02.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on January 4, 2010.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Boucadair, et al. Expires January 4, 2010 [Page 1]
Internet-Draft Port Range Architecture July 2009
Abstract
This memo proposes a solution, based on fractional addresses, to face
the IPv4 public address exhaustion. It details the solution and
presents a mock-up implementation, with the results of tests that
validate the concept. It also describes architectures and how
fractional addresses are used to overcome the IPv4 address shortage.
A comparison with the alternative Carrier-Grade NAT (CG-NAT)
solutions is also elaborated in the document. The IPv6 variant of
this solution is described in a companion draft.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Context . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2. Tentative Solutions: Overview and Limitations . . . . . . 4
1.3. Contribution of this draft . . . . . . . . . . . . . . . . 6
2. Conventions used in this document . . . . . . . . . . . . . . 6
3. Port Range Architecture: Overall Procedure . . . . . . . . . . 7
3.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . 7
3.2. Basic Principles . . . . . . . . . . . . . . . . . . . . . 8
3.3. Applicability Use Cases . . . . . . . . . . . . . . . . . 9
3.3.1. CPE . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3.2. End Host . . . . . . . . . . . . . . . . . . . . . . . 9
3.3.3. Point-to-Point Links . . . . . . . . . . . . . . . . . 10
3.3.4. Point-to-Point Tunneled Links . . . . . . . . . . . . 11
4. Retrieving IP Configuration Data . . . . . . . . . . . . . . . 12
4.1. Assumption . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2. Procedure . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.1. Overview . . . . . . . . . . . . . . . . . . . . . . . 12
4.3. An alternative to avoid DHCP Server modifications . . . . 13
5. Required Modifications . . . . . . . . . . . . . . . . . . . . 16
5.1. CPE . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2. End-user Terminals . . . . . . . . . . . . . . . . . . . . 17
5.3. Service Provider Infrastructure . . . . . . . . . . . . . 17
5.4. DHCP Server Implementations . . . . . . . . . . . . . . . 18
6. Port Range Router . . . . . . . . . . . . . . . . . . . . . . 18
6.1. Main Function . . . . . . . . . . . . . . . . . . . . . . 18
6.2. Routing Considerations: Focus on IGP . . . . . . . . . . . 19
6.3. Binding Table . . . . . . . . . . . . . . . . . . . . . . 20
6.4. Provisioning . . . . . . . . . . . . . . . . . . . . . . . 20
6.4.1. Needs . . . . . . . . . . . . . . . . . . . . . . . . 20
Boucadair, et al. Expires January 4, 2010 [Page 2]
Internet-Draft Port Range Architecture July 2009
6.4.2. Option 1: CPE-Provisioned PRR . . . . . . . . . . . . 20
6.4.3. Option 2: Provider-Provisioned PRR . . . . . . . . . . 21
7. Localization Inside a Service Provider's Domain . . . . . . . 21
8. Fragmentation . . . . . . . . . . . . . . . . . . . . . . . . 22
9. Multicast . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10. IGD 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
11. IPSec . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
12. ICMP and Other Portless Protocols . . . . . . . . . . . . . . 25
13. 6to4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
14. Protocols not supported by PRR . . . . . . . . . . . . . . . . 26
15. Comparison with CG-NAT/LSN . . . . . . . . . . . . . . . . . . 26
15.1. Generic Hurdles and Focus on Transparency to
applications which enclose IPv4 address in their
protocol messages . . . . . . . . . . . . . . . . . . . . 26
15.2. Focus on Legal Storage . . . . . . . . . . . . . . . . . . 27
15.3. Session Handling in CG-NAT . . . . . . . . . . . . . . . . 30
15.4. Peer-to-Peer applications . . . . . . . . . . . . . . . . 31
16. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 31
17. Security Considerations . . . . . . . . . . . . . . . . . . . 31
18. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 32
19. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 32
20. References . . . . . . . . . . . . . . . . . . . . . . . . . . 32
20.1. Normative References . . . . . . . . . . . . . . . . . . . 32
20.2. Informative References . . . . . . . . . . . . . . . . . . 33
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 34
Boucadair, et al. Expires January 4, 2010 [Page 3]
Internet-Draft Port Range Architecture July 2009
1. Introduction
1.1. Context
It is commonly agreed by the Internet community that the exhaustion
of public IPv4 addresses is an ineluctable fact. In this context,
the community was mobilized in the past to adopt a promising solution
(in particular with the definition of IPv6). Nevertheless, this
solution is not globally activated by Service Providers for both
financial and strategic reasons. In the meantime, these Service
Providers are not indifferent to the alarms recently emitted by the
IETF particularly by the reports presented within the GROW working
group (Global Routing Operations Working Group) meetings.
G. Huston introduced an extrapolation model to forecast the
exhaustion date of IPv4 addresses managed by IANA. This effort
indicates that if the current tendency of consumption continues at
the same pace, IPv4 addresses exhaustion of IANA's pool would occur
in 2011, while RIRs'pool would be exhausted in late 2012. The state
of the current consumption of public IPv4 addresses is daily updated
and is available at this URL:
http://www.potaroo.net/tools/ipv4/index.html.
1.2. Tentative Solutions: Overview and Limitations
In order to solve this depletion problem, Service Providers need to
investigate and enable means to ensure the deployment of their
service offerings and their delivery to end users. Two strands may
be followed:
(1) Migrate to IPv6:
IPv6 has been introduced for several years as the next version of the
IP protocol. This new version offers an abundance of IP addresses as
well as several enhancements compared to IPv4 especially with the
adoption of hierarchical routing (and therefore allows reducing the
routing tables size). IPv6 specifications are mature and current
work within the IETF is related to operational aspects.
Nevertheless, Service Providers have not largely activated IPv6 in
their networks yet.
However, even if a Service Provider activates IPv6, it will be
confronted with the problem to ensure a global connectivity towards
nowadays Internet v4. Mechanisms such as NAT-PT (Network Address
Translation Protocol Translation) were introduced to ensure the
interconnection between two heterogeneous realms (i.e., IPv4/IPv6)
and to ensure a continuity of IP communications (i.e., end-to-end).
It is out of scope of this document to analyze the hurdles of these
Boucadair, et al. Expires January 4, 2010 [Page 4]
Internet-Draft Port Range Architecture July 2009
solutions.
Despite the current IPv6 deployment situation, IPv6 is the viable
alternative to offer IP connectivity services to a large number of
customers. From this perspective, Service Providers should avoid
introducing new functions and nodes which may be problematic when
envisaging migrating to IPv6. This critical requirement should not
be taken into account only during the technical engineering phase,
but also when elaborating required CAPEX (Capital Expenditure)/OPEX
(Operational Expenditure) estimation of activating alternative
schemes to solve or to reduce the impact of the IPv4 address
exhaustion phenomenon.
Note that this requires deploying interconnection mechanisms with the
already existent IPv4 realms. This cost overhead should be
considered in transition scenarios.
(2) Enhance current IPv4 architectures and optimize the assignment
of IPv4 addresses:
A first example of the implementation of this option is the
introduction of a second level of NAT, called Provider-NAT or Carrier
Grade NAT (CG-NAT). This node is located in the Service Provider
domain. In such option, only private addresses are assigned to end-
user home gateways, which still perform their own NAT. The CG-NAT is
responsible for translating IP packets issued with private addresses
to ones with publicly routable IPv4 addresses when exiting the domain
of the Service Provider.
The introduction of the CG-NAT will have an important impact on the
applications. Some services will only work in a degraded mode, some
will even not work at all (refer to Section 15 for more details about
encountered hurdles).
A variant of CG-NAT, called DS-lite, is proposed in
[I-D.ietf-softwire-dual-stack-lite]. In this mode, only one NAT
level is maintained but it is located in the service provider's
network. Unlike Provider-NAT, IPv6 is used to convey traffic isseud/
destined from/to customer's device.
Another example of this second option is the proposal that has been
made to release IPv4 class E addresses [I-D.fuller-240space]:
concretely to reclassify 240/4 as usable unicast address space. The
rationale of this proposal is that since the community has not
concluded whether the E block should be considered public or private,
and given the current consumption rate, it is clear that the block
should not be left unused. This proposal requires updating IP-
enabled equipment so as to treat correctly IPv4 addresses belonging
Boucadair, et al. Expires January 4, 2010 [Page 5]
Internet-Draft Port Range Architecture July 2009
to 240/4 blocks. These addresses should be routable and announced
for instance between adjacent Autonomous Systems (ASes) through BGP
(Border Gateway Protocol) for instance. An exhaustive study should
be undertaken to evaluate the economic and technical impact of such
new policy. Another alternative is to re-classify class E address as
private ones [I-D.savolainen-indicating-240-addresses].
1.3. Contribution of this draft
This memo specifies an alternative solution to the Double NAT
architecture which aims at solving the depletion problem as
encountered by current ISPs. The proposed solution, called Port
Range based architecture is session stateless and does not alter the
various offered services. The solution presented in this document
does not require severe modifications to current engineering
practices as adopted by major Service Providers. Furthermore, the
solution is scalable and can be deployed in several variants,
especially to prepare the migration towards IPv6.
This draft describes a lightweight architecture that may be deployed
by Service Providers to offer IP connectivity services to their
already subscribed customers or to new ones. This document provides
an implementation scenario. Service Providers are free to enforce
their own engineering rules based on their internal policies and
available technological means as activated in their IP
infrastructure. The solution is flexible enough to be accommodated
in various contexts.
The scalability of this solution is similar to current deployed IP
architectures. No session-related states are maintained in core
nodes operated by a given Service Provider.
This solution can be activated in an end host, CPE (Customer Premises
Equipment), or any other device able to constraint its source port
numbers.
An IPv6 variant of this solution is described in
[I-D.boucadair-behave-ipv6-portrange].
2. Conventions used in this document
The key words MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL in this document are to be
interpreted as described in RFC-2119 [RFC2119].
The following abbreviations are used within this document:
Boucadair, et al. Expires January 4, 2010 [Page 6]
Internet-Draft Port Range Architecture July 2009
- ASN GW: Access Service Network Gateway
- CGN: Carrier Grade Network Address Translator
- CPE: Consumer Premises Equipment, a device that resides between
Internet service provider's network and consumers' home network.
- GGSN :Gateway GPRS Support Node
- GPRS: General Packet Radio Service
- PDN GW: Packet Data Network Gateway
- PDSN: Packet Data Serving Node
- PRR: Port Range Router
3. Port Range Architecture: Overall Procedure
3.1. Introduction
As an alternative to the Double NAT solution, which suffers from
several drawbacks, a second alternative is proposed within this
document. The motivations for introducing this second alternative
are as follows:
- Not to alter current (IPv4-based) services delivery and to not
impact the introduction of future services;
- Avoid maintaining sessions states at the core network.
Stateless solutions are privileged;
- Ease management functions (including provisioning, configuration
operations, etc.);
- Optimise CAPEX and OPEX: As shown latter in this draft, the
functional requirements to implement the proposed procedure are
lightweight. Only slight modifications are required to be
brought. Furthermore, the offered services are not impacted.
Management practices would remain as today. For example, because
the solution described in this memo does not handle dynamic NAT
mappings (contrary to the CG-NAT), the planned maintenance
operations (replacement of involved network equipment) would not
impact the delivered services as a CG-NAT-based solution would do;
- Minor impact on routing and addressing architectures;
Boucadair, et al. Expires January 4, 2010 [Page 7]
Internet-Draft Port Range Architecture July 2009
- Transparent to end-users: The same practices as today's ones
will remain (e.g., Port forwarding on CPE still possible -provided
the port is within the allocated Port Range-);
- Usability easiness;
- Facilitate functional separation (Service and Network): For
instance, and unlike CG-NAT, the problem to run SIP-based services
above a third party IP infrastructure would not be encountered
with the proposed solution;
- Ease implementing legal requirements (optimize storage of legal
data);
- Ease migration to a long term solution such as IPv6;
This section focuses only on the IPv4 variant of the solution. Other
variants have been defined to integrate IPv6 and offer a global IP
connectivity services including towards IPv6 realms in a stateless
manner. Companion Internet Drafts will be submitted latter.
3.2. Basic Principles
The major idea is to assign the same IP address to several end-users'
devices (e.g., Home Gateways (HGW) embedding NAT, but that could be
other types of devices embedding NAT) and to constrain the (source)
port numbers to be used by each device. In addition to the assigned
IP address to access IP connectivity services, additional parameters
are also communicated with the customer's device. These additional
parameters indicate which Ports or Port Range(s) is/are assigned to
the customer's devices.
In the remaining part of this draft, the above mentioned public
address is denoted as Primary IP Address.
For outbound communications, a given HGW proceeds to its classical
operations except the constraint to control the source port number
assignment so as to be within the Port Range assigned by its IP
connectivity Service Provider. The traffic is then routed inside the
Service Provider's domain and delivered to its final destination
(within the service domain or to external domains).
For inbound communications (i.e., Towards customers attached to the
Service Provider which has activated the procedure detailed in this
memo), the traffic is trapped by a dedicated function called: Port
Range Router (PRR). This function may be embedded in current routers
or hosted by new nodes to be integrated in the IP infrastructure of
these Service Providers. Appropriate routing tuning policies are
Boucadair, et al. Expires January 4, 2010 [Page 8]
Internet-Draft Port Range Architecture July 2009
enforced so as to drive the inbound traffic to cross a PRR (see
Section 6 for more details). Particularly, each PRR correlate the
Primary IP Address and information about the allowed port values with
a specific identifier called: routing identifier (e.g., secondary
IPv4 address, IPv6 address, point-to-point link identifier, etc).
This routing identifier is used to route the packets to the suitable
device among all those owning the same IP address (See Section 6.1).
Note that for some reasons (e.g., Ease implementation of port-driven
RPF (Reverse Path Forwarding) checking, anti-spoofing techniques,
etc.), outbound traffic may be constrained to invoke the PRR
function. This feature for outbound packets is considered as an
engineering option. Service Providers are free to enforce it or not.
3.3. Applicability Use Cases
The following sub-sections provide a non exhaustive list of the port
range solution applicability use cases. Other scenarios may be
envisaged.
3.3.1. CPE
For deployment considerations and reduction of impact on terminals,
the recommended scenario (in the context of DSL-type service
offerings) of the deployment of the solution is a Provider
provisioned CPE. This scenarios hides the connectivity solution and
its associated addressing architecture. Machines behind the CPE
continue to behave as today. No modification is required on end
hosts.
3.3.2. End Host
When a host, which is capable of an IP address and a port range, but
some of the applications on the host may have trouble using those
addresses (e.g., they require a specific port to operate), as an
implementation choice, the host may hide the port restricted nature
of the allocated address by implementing an internal NAT as
illustrated in the figure:
Boucadair, et al. Expires January 4, 2010 [Page 9]
Internet-Draft Port Range Architecture July 2009
Host
+---------------------+
+ Application +
+ | +
+ | IPv4p +-----+ + IPv4 address and a port range
+ |-------| NAT | +---------------------------------
+ +-----+ +
+ +
+---------------------+
Figure 1: Internal NAT in a host
3.3.3. Point-to-Point Links
In point-to-point links it can be assumed that there are only two
communicating parties on the link, and thus IP address collisions are
easy to avoid.
In wireless cellular networks host attached to an access router, such
as 3GPP PDN GW or WiMAX ASN GW , over a point-to-point link providing
layer 2 IPv4 transport capability.
In order to be able to allocate an IP address together with a port
range to a host, the access router needs to implement DHCP server or
at least act as a DHCP relay or DHCP proxy , while a DHCP server
exists in the backend. These setups are illustrated in the following
figure.
+--------+ |
3GPP ---Point to Point link--| 3GPP |------|
host <-IPv4 EPS bearer--> | PDN GW | |
+--------+ |
| IPv4 Internet
+--------+ |
WiMAX ---Point to Point link--| WiMAX |------|
host <-----IPv4 CS------> | ASN GW | |
+--------+ |
Figure 2: Point-to-point physical links
As each host is attaching to the access router with an individual
link, both modified and unmodified hosts can be supported
simultaneously. This enables incremental deployment of modified
hosts that are supporting public IPv4 address conservation by using
DHCP to assign IPv4 address and a port range, while continuing to
support the legacy hosts using DHCP as currently specified.
Boucadair, et al. Expires January 4, 2010 [Page 10]
Internet-Draft Port Range Architecture July 2009
In this scenario, IPv6 addresses can be used in parallel with any
IPv4 address, therefore no tunneling is necessary.
If PPP is used, port restricted IPv4 address can also be configured
in PPP IPCP option as described in
[I-D.boucadair-pppext-portrange-option].
3.3.4. Point-to-Point Tunneled Links
From DHCP point of view, tunneled link scenario does not differ very
much from L2 point-to-point links as described in the previous
section, although there are general concerns regarding tunnels (e.g.,
decreased MTU).
The tunnel is established between a host (or a CPE) and a tunnel
endpoint in the host Operator's network. In different scenarios, the
tunnel endpoint may be placed at different locations. The tunnel
endpoint can be at the first hop router such as 3GPP2 PDSN or 3GPP
PDN-GW, or farther off in the network. In one scenario, the tunnel
endpoint can be the CGN of DS-Lite
[I-D.ietf-softwire-dual-stack-lite].
These example setups are illustrated in the following figure.
Tunnel endpoints,
implementing DHCPv4
server/relay/proxy
+-------------+
Host ====IPv4 over IPv6==== | 3GPP2 | |
<---PPP & IPv6CP ----> | PDSN |------|
(point-to-point) +-------------+ |
|
+-------------+ |
Host ====IPv4 over IPv6==== | 3GPP |------| IPv4 Internet
<--IPv6 PDP context--> | GGSN | |
(point-to-point) +-------------+ |
|
+-------------+ |
Host ====IPv4 over IPv6==== | IETF |------|
<---- IPv6-only -----> | DS-Lite CGN | |
network +-------------+
Figure 3: Point-to-point links as IPv4 over IPv6 tunnels over three
different accesses
Having the tunnel endpoint at the first hop router can be beneficial
in setups where arrangement of native dual-stack transport for the
last mile is not feasible or cost-effective approach. This can be
Boucadair, et al. Expires January 4, 2010 [Page 11]
Internet-Draft Port Range Architecture July 2009
the case e.g., in 3GPP networks, prior 3GPP Release-8, where a PDP
context is capable of transporting only IPv4 or IPv6 packets, and for
dual-stack access two parallel PDP contexts are required.
For networks which use IP(v6)CP to configure IPv4 and IPv6 addresses
to the host, allocating an IPv4 address and a port range to the host
to prevent running out of available IPv4 addresses, can also be a
feasible solution. In these deployment scenarios, IPv6CP would be
used to configure an IPv6 address to the host. The host would then
set up the tunnel and use the DHCPv4 extensions defined in this
document to request an IPv4 address together with a port range.
Examples of such networks include 3GPP2 and BRAS.
4. Retrieving IP Configuration Data
4.1. Assumption
In the context of this section, it is assumed that DHCP (Dynamic Host
Configuration Protocol, [RFC2131]) is used to convey IP connectivity
information. Other alternatives, such as PPP (Point-to-Point
Protocol, [RFC1661] and [I-D.boucadair-pppext-portrange-option]), may
be used. The procedure described in this section is only an
illustration example. It may be adapted so as to be able to apply in
other technological contexts.
4.2. Procedure
4.2.1. Overview
At a bootstrapping phase, a given HGW issues a DHCP_DISCOVER message.
This message is sent in broadcast. This message can be relayed by a
DHCP Client Relay or be received directly by a DHCP Server. Once
this message is received by a DHCP Server, this latter answers the
requester by a dedicated DHCP_OFFER message containing a
configuration offer.
The exchange which intervenes is illustrated in the following figure:
Boucadair, et al. Expires January 4, 2010 [Page 12]
Internet-Draft Port Range Architecture July 2009
+-----+ +-------------+
| HGW | | DHCP Server |
+-----+ +-------------+
| |
| (1) DHCP DISCOVER |
|------------------------------>|
| |
| |
| (2) DHCP OFFER |
|<------------------------------|
| |
Figure 4: DHCP Call Flow
A DHCP OFFER message encloses a set of IP-related information so as
to access IP connectivity service. Particularly, it includes an IP
address together with a new DHCP option, see:
[I-D.bajko-pripaddrassign].
Additional information may be included in the DHCP offer.
The use of Port Mask DHCP sub-option (similar to subnet mask) makes
it possible to extend the notion of Port Range with non-continuous
values, for the sake of flexibility.
A Port Range is then a set of ports that all have in common a subset
of pre-positioned bits.
Once a Port Range information is received by a HGW, it constrains its
NAT operations to the provisioned range. The number of customers to
which an ISP can assign the same IP address depends on the number of
allowed port numbers per user. Thus, if N bits are used to build the
Port Mask, 2^N customers can be provided with the same IP address.
For example: If N == 3, then the Service Provider multiplies by 8 its
capacity in term of number of customers to which the connectivity
service may be delivered.
In the remaining part, Port Mask and Port Range are used
interchangeably.
4.3. An alternative to avoid DHCP Server modifications
To avoid alteration of already in place DHCP servers, this section
presents an alternative to implement Port Range assignment procedure.
This alternative relies on DHCP Relay Clients or DHCP proxies and not
on DHCP servers. These latter are kept unchanged. Their main
function is to assign an available IP address. This address is
assumed to be routed inside the Service Provider domain.
Boucadair, et al. Expires January 4, 2010 [Page 13]
Internet-Draft Port Range Architecture July 2009
DHCP proxies, in cooperation with the PRR, maintains a set of pre-
assignments based on a pre-provisioned Service Provider policy
regarding how to build Port Ranges. As an example, if the
implemented policy is to assign the same IP address to 4 customers,
then 4 Port Ranges per IP address are statically built and then
assigned to customers upon request.
In this context, DHCP proxies do not relay any IP assignment request
until all available Port Ranges are allocated.
Figure 5 and Figure 6 provide an example of this option. In this
example, CPE-1 and CPE-2 are two CPEs of two distinct customers.
CPE-1 sends first its DHCP DISCOVER message. This message is
received by the DHCP proxy. Upon receipt, a lookup on available IP
address and Port Range is achieved by the DHCP proxy.
Since no IP address is available, a DHCP DISCOVER message is
forwarded to the DHCP Server. A DHCP OFFER is then sent back. This
offer is trapped by the DHCP proxy.
The assigned IP address is retrieved and a pre-allocation of a Port
Range is achieved. The offer is then updated with the Port Range
Information and then relayed to CPE-1.
The remaining operations are the same operations as current DHCP
exchanges.
Boucadair, et al. Expires January 4, 2010 [Page 14]
Internet-Draft Port Range Architecture July 2009
+-----+ +-----+ +--------+ +------+
|CPE-1| |DHCP | |Binding | |DHCP |
| | |proxy| |Table | |Server|
+-----+ +-----+ +--------+ +------+
| (1)DHCP DISCOVER | | |
|------------------->| | |
| |(2) Check if there| |
| | is an available | |
| | IP @ and a | |
| | Port Range | |
| |----------------->| |
| | | |
| |(3) No Available @| |
| | | |
| |<-----------------| |
| | | |
| | (4) DHCP DISCOVER| |
| |-------------------------------------->|
| | (5) DHCP OFFER(IP-Pub-1) |
| |<--------------------------------------|
| | (6) DHCP REQUEST (IP-Pub-1) |
| |-------------------------------------->|
| | (7) DHCP ACK(IP-Pub-1) |
| |<--------------------------------------|
| | | |
| |(8)Add IP-Pub-1 | |
| | to Ports Range | |
| | allocation, | |
| |and pre-assign a |
| | Port Range to CPE1 |
| |----------------->| |
|(9)DHCP OFFER(IP-Pub-1, PR1) | |
|<-------------------| | |
| | | |
|(10)DHCP REQUEST(IP-Pub-1, PR1) | |
|------------------->| | |
| |(11) Assign PR1 to| |
| | CPE1 | |
| |----------------->| |
|(10)DHCP ACK(IP-Pub-1, PR1) | |
|------------------->| | |
| | | |
Figure 5: First Example
If CPE-2 requests an IP address, it issues a DHCP DISCOVER message.
This message is not relayed to the DHCP Server. A lookup request is
executed by the DHCP proxy to check if an IP address and a Port Range
Boucadair, et al. Expires January 4, 2010 [Page 15]
Internet-Draft Port Range Architecture July 2009
are available to be assigned. In this example, a positive answer is
sent to the DHCP proxy. A DHCP Offer is then sent to CPE-2 as
illustrated in Figure 6.
+-----+ +-----+ +--------+ +------+
|CPE-2| |DHCP | |Binding | |DHCP |
| | |proxy| |Table | |Server|
+-----+ +-----+ +--------+ +------+
| (1)DHCP DISCOVER | | |
|------------------->| | |
| |(2) Check if there| |
| | is an available | |
| | IP @ and a | |
| | Port Range | |
| |----------------->| |
| | | |
| |(3) OK (IP1) | |
| | | |
| |<-----------------| |
| | | |
| | | |
| |(4) Allocate IP1 | |
| |and Pre-assign a | |
| |Port Range to CPE2 |
| |----------------->| |
|(9)DHCP OFFER(IP-Pub-1, PR2) | |
|<-------------------| | |
| | | |
|(10)DHCP REQUEST(IP-Pub-1, PR2) | |
|------------------->| | |
| |(11) Assign PR2 to| |
| | CPE2 | |
| |----------------->| |
|(10)DHCP ACK(IP-Pub-1, PR2) | |
|------------------->| | |
| | | |
Figure 6: Second Example
5. Required Modifications
5.1. CPE
Above, we have quoted the case of Home Gateway but the solution can
fit to any kind of Customer Premises Equipment (CPE).
In order to activate the aforementioned solution, slight
Boucadair, et al. Expires January 4, 2010 [Page 16]
Internet-Draft Port Range Architecture July 2009
modifications are required to be supported by CPEs. Concretely, CPEs
MUST be able to constrain their NAT operations and to use only source
port numbers within the allocated Port Range. If an IP packet is
received by a given Port Range-enabled CPE, with a destination port
number outside the assigned Port Range, the packet MUST be discarded.
Moreover, Port Range-enabled CPEs MUST be able to enforce
configuration data received from the Service Providers so as to
constrain its Port Range. More particularly, if DHCP is used to
convey configuration data, a particular DHCP option (to be assigned
by IANA) is to be supported by that CPE.
According to the enforced routing identifier mode, a de-encapsulation
function MAY be required to be supported.
5.2. End-user Terminals
In some deployment scenarios (e.g., mobile), end-hosts should be
updated. Concretely, end-hosts MUST be able to constrain their
source port numbers and to use only source port numbers within the
allocated Port Range. If an IP packet is received by a given Port
Range-enabled end-user terminal, with a destination port number
outside the assigned Port Range, the packet MUST be discarded.
Moreover, Port Range-enabled terminals MUST be able to enforce
configuration data received from the Service Providers so as to
constrain its Port Range.
According to the enforced routing identifier mode, a de-encapsulation
function MAY be required to be supported.
5.3. Service Provider Infrastructure
The IP infrastructure of a given IP Service Provider is maintained
slightly unchanged when deploying the Port Range architecture based
solution. Only, a new function is introduced. This new function is
denoted as PRR. This function is responsible for routing packets to
the appropriate end-user's device among those to which the same IP
address is assigned by the Service Provider. This operation is
denoted as Port-Driven Routing operation since the destination IP
address is not sufficient to handle routing operations and the
information related to destination port is also required.
Except the PRR, all classical operations and practices remain as
today's ones.
A PRR can be stand-alone server, or it can be hosted into other boxes
such existing routers, PDN GW, ASN GW, etc.
Boucadair, et al. Expires January 4, 2010 [Page 17]
Internet-Draft Port Range Architecture July 2009
5.4. DHCP Server Implementations
In case DHCP is used to convey IP connectivity information to
customers' devices, DHCP server implementations may be modified
accordingly. Indeed, DHCP server implementation should be modified
so as to be able to support additional options such as Port Range
DHCP option. The DHCP server assignment policy can be tuned by the
Service Provider. A given Service Provider can provision its DHCP
server with the Port Range to be allocated to end users' devices.
A second alternative to assign Port Ranges is described in
Section 4.3. This alternative does not require any modification of
the DHCP Server. Nevertheless, new changes are required to be
supported by DHCP proxies.
6. Port Range Router
6.1. Main Function
As stated above, the main function implemented by a PRR is a port-
driven routing. In order to implement the port-driven routing, the
following operations are achieved by a given PRR:
In order to implement the port-driven routing, the following
operations are achieved by a given PRR:
1. It retrieves both destination IP address and destination port
number.
2. Based on this couple, the PRR consults its binding table and
retrieves the routing identifier.
Several modes may be envisaged to assign a routing identifier to be
used as a deterministic discriminator to unambiguously identify a
device among all those having the same IP address.
Hereafter are provided some implementation alternatives:
1. If a Secondary-IP address is used as the routing identifier: the
PRR consults its binding table and retrieves the corresponding
Secondary-IP address associated with a (Destination IP, Port
Mask). Once retrieved, the PRR encapsulates the original packets
in an IPv4 one with a destination IP address equal to
Secondary-IP. This packet is then routed according to
instantiated IGP (Interior Gateway Protocol) routes. Once
received by the CPE, a de-encapsulation operation is achieved.
The original packets is then treated and handled locally. If
Boucadair, et al. Expires January 4, 2010 [Page 18]
Internet-Draft Port Range Architecture July 2009
destination port of that packet is within the Port Range of that
CPE, and depending on the local NAT implementation, the packet
may be accepted and then proceed to classical NAT operation.
Otherwise, the packet is dropped. Note that:
A. The scope of the secondary address is limited to the access
segment
B. The secondary IP address may be an IPv6 address
2. Instead of encapsulation, and if source routing is supported, an
explicit route is forced. A loose route is indicated in the
packets. This loose route contains at least Secondary-IP. The
routing of the resulting packet will be based on that address and
not the destination one. The packet will be then received by the
CPE with that Secondary-IP address. Then, the CPE will route the
packet based on the final destination IP address. Since that
address is also an IP address of that CPE, the packet is handled
locally. The remaining operations are similar to the ones
implemented by current CPEs.
3. If disjoint routes have been pre-installed so as to unambiguously
identify the targeted device among all those having the same IP
address, the PRR consults its binding tables and retrieves the
index of the route corresponding to that (Destination IP, Port
Mask) pair. The original packet is then sent over that route.
Since the routes are disjoint, the packet will be received by the
targeted CPE. A example is the case where the PRR and the CPEs
are directly linked by Ethernet, the route is then identified by
the Ethernet MAC address of the CPE.
4. The routing identifier can also be the identifier of the L2
point-to-point link
As for inbound, a new operation is introduced in the path, this
operation is a port-driven operation with no modification of the
original packet. Further evaluation should be undertaken so as to
assess the impact of this operation.
The performance experienced by outbound packets is not impacted since
no alteration of the issued packets is to be enforced in the path.
The experienced QoS (Quality of Service) is then the same as the
currently deployed one.
6.2. Routing Considerations: Focus on IGP
A PRR is inserted in the inbound path in order to execute a port-
driven routing. This constraint is translated into an IGP one.
Boucadair, et al. Expires January 4, 2010 [Page 19]
Internet-Draft Port Range Architecture July 2009
Indeed, a given PRR MUST advertise in IGP the primary IP addresses it
handles. Doing so, all inbound packets will cross that PRR.
In case IPv4 Secondary-IP addresses are used to uniquely identify a
CPE among all those having the same Primary-IP address, IPv4
Secondary-IP addresses MUST NOT be routable addresses inside core
network. These addresses MUST NOT be reachable from the Internet.
An example of the scope of those addresses is up to the frontier of
an IP access POP (Point of Presence).
6.3. Binding Table
In order to implement port-driven routing operations, a PRR maintains
a binding table which is a collection of entries correlating (IP
address, Port Mask) with a routing identifier.
This table should not be confused with the NAT table as maintained by
a CG-NAT.
6.4. Provisioning
6.4.1. Needs
In order to be able to treat received packets and then to proceed to
port-driven routing, a PRR MUST be provisioned appropriately.
Concretely, and as stated above, a given PRR needs to maintain a
binding table which correlates a destination IP address and a Port
Mask with a routing identifier (such as a secondary IPv4 address,
IPv6 address, routing index, MAC address, PPP session identifier,
etc.). This binding table can be provisioned either by the Service
Provider (owing to an internal interface) or by the CPE itself once
IP connectivity information has been received from the service
platform.
These two options are described hereafter. Service Providers are
free to implement the option which meets its internal engineering
policies.
6.4.2. Option 1: CPE-Provisioned PRR
Once its IP connectivity configuration is retrieved owing to a
dedicated means such as DHCP, a given CPE enforces this new
configuration. Particularly, the new received information may
contain the following information:
{Primary-IP, Port Mask, Default_PRR, Routing Identifier}
In case the adopted method for the routing identifier (mentioned in
Boucadair, et al. Expires January 4, 2010 [Page 20]
Internet-Draft Port Range Architecture July 2009
Section 6.1) is a Secondary-IP address, a message is issued by the
CPE towards its Default PRR. This message notifies that PRR about
the new association: i.e., (Primary-IP, Port Mask) with Secondary-IP.
This notification is achieved owing to a new message denoted as BIND.
Once received by the PRR, an ACK message must be sent as response.
If no ACK message is received, the CPE re-transmits its BIND message.
The procedure is sketched in the following figure:
+-----+ +-----+
| HGW | | PRR |
+-----+ +-----+
| |
| (1) BIND |
|------------------------------>|
| |
| |
| (2) ACK |
|<------------------------------|
| |
Figure 7: Example of CPE-provisioned PRR
Authentication means may be required to prevent creating hostile
bindings.
6.4.3. Option 2: Provider-Provisioned PRR
Here, the provisioning of PRR binding table is undertaken by the
Service Provider owing to the activation of appropriate management
interfaces. These interfaces are internal to Service Provider's
domain and are not visible to end-users. Exchanges between the PRR
and the management realms are operated by the Service Provider. An
implementation scenario of this option, is that once the DHCP server
has assigned an IP address together with a Port Range a dedicated
message is issued towards a PRR so as to instantiate a new entry in
the binding table of that PRR. The entry can be refreshed or dropped
once required.
In both options, the structure of the binding tables and the state
machine of the PRR are identical.
7. Localization Inside a Service Provider's Domain
Each service Provider is free to adopt its internal policies for the
deployment of PRRs. Nevertheless, we recommend deploying those nodes
Boucadair, et al. Expires January 4, 2010 [Page 21]
Internet-Draft Port Range Architecture July 2009
at access segment in order not to significantly impact end-to-end
routing optimization. A PRR function can be embedded in an access
router, a DSLAM, etc.
Several engineering options may be enforced:
o A given IP address is shared between several customers located in
the same access POP: In this scenario, only access routers should
be updated to support a PRR function. Doing so, communication
(more precisely IGP routes) between the customers located in the
same POP are optimised.
o Re-use the same IP address in several access POP and assign the
same port range to all customers of the same POP: In this
configuration, a given IP address is assigned to a single customer
per POP. For intra-domain communications, and for optimisation
purposes, all access routers should enable a PRR function. A far
head router in the network should be activated to route inter POP
traffic.
8. Fragmentation
In order to deliver a fragmented IP packet to its final destination
(among those having the same IP address), the PRR should activated a
dedicated procedure which described hereafter:
1. Check if the received packet is a fragment: ((MF == 1 && Fragment
Offset == 0) || (Fragment Offset != 0)), else apply the classical
PRR routing procedure;
2. Check if this fragment is the first one (MF == 1 && Fragment
Offset == 0)
2.1. In addition to the information retrieved to enforce port
range routing, retrieve the source IP address and packet
identifier. A fragmentation entry is instantiated. A timer
(referred to as fragmentation timer) is associated with this
entry. A clean up procedure is achieved when the timer
expires.
2.2. Retrieve the binding entry to be used to route this
first fragment. A pointer to this entry is added to the
fragmentation entry. A fragmentation entry includes:
destination IP address, source IP address, Identifier, binding
entry identifier and timer.
Boucadair, et al. Expires January 4, 2010 [Page 22]
Internet-Draft Port Range Architecture July 2009
3. Check if this fragment is not the first one (Fragment Offset !=
0)
3.1. Retrieve the source IP address, destination IP address
and Identifier;
3.2 Check if an entry having the same source IP address,
destination IP address and Identifier is instantiated in the
fragmentation table
3.2.1 If yes, retrieve the binding entry pointer from the
fragmentation table. Use the corresponding entry to route
the fragment.
3.2.1 If not (fragments are not received in the order),
launch a timer (which value is small than the fragmentation
timer). This timer is referred to as fragmentation order
timer. Upon expire of this timer, go to Step 3.2. This
step is repeated two or three times. If it fails, the
fragment is dropped.
Note that it is recommended to use a PMTUD path discovery mechanism
(e.g., [RFC1191]).
Security issues related to fragmentation are out of scope of this
document. For more details, refer to [RFC1858]
9. Multicast
In the previous sections, only unicast considerations have been
elaborated. This section focuses on the impacts on multicast
mechanisms and services when a Port Range based solution is
activated.
Since the proposed solution does not require any modification on the
core network of a given service provider / IP network provider,
protocols to build and maintain multicast trees (e.g., PIM-SM
[RFC4601], M-OSPF [RFC1584]) can be activated without any
modification. Concretely, current multicast configurations on core
routers and nodes can be applied without any adaptation.
As far as multicast group membership is concerned, classical
procedures, e.g., IGMPv2 [RFC2236], or IGMPv3 [RFC3376], may be
impacted.
Boucadair, et al. Expires January 4, 2010 [Page 23]
Internet-Draft Port Range Architecture July 2009
Concretely:
1. If a secondary IP address (see Section 6.1) is used, the
subscription to a multicast group can be done using this address.
Thus, IGMP operations to receive traffic (i.e., IGMP requests)
are not impacted and multicast traffic can be forwarded to the
subscribed hosts;
2. If the shared IP address is used to issue IGMP requests,
A. If distinct public IP addresses are assigned to each customer
which device is attached to the same multicast router:
classical IGMP operations are valid. No adaptation is to be
enforced. Multicast traffic can be forwarded to each
subscribed users without ambiguity.
B. If a same public IP address is assigned to several customers
which devices are attached to the same multicast router: the
attached multicast router should correlate the request source
with the binding table to unambiguously forward the multicast
traffic to the appropriate subscribed user. More precisely,
IGMP states should be updated to include the routing
identifier to be used to forward traffic to the subscribed
host. Appropriate means to uniquely distinguish the source
of IGMP request among those having the same IP address should
be implemented.
+ To avoid the modification of IGMP, several virtual router
instances can be instantiated into the same physical node.
Each virtual router manages only distinct IP addresses.
This configuration is similar to the bullet a.
In addition to these considerations, a hurdle can be encountered when
using IGMPv3. Indeed, IGMPv3 messages can specify specific sources
to be used to be excluded. If a shared IP address is assigned to
those sources, traffic issued by other sources having the same IP
address can be impacted. This scenario is not viable in current
multicast deployments since the source of multicast traffic is under
control of a service provider (e.g., head ends in the context of IP
TV service offering) and a not shared IP address would be assigned to
head ends.
10. IGD 2.0
Version 2.0 of IGP specification recommends the usage of a new method
called AddAnyPortMapping() instead of AddPortMapping(). This new
specification will ease the deployment of shared IP addresses.
Boucadair, et al. Expires January 4, 2010 [Page 24]
Internet-Draft Port Range Architecture July 2009
11. IPSec
Even if IPSec is not deployed for mass market, impacts of solutions
based on shared IP addresses should be evaluated and assessed.
[RFC3947] proposes a solution to solve complications issues
documented in [RFC3715]. Below is described an analysis of the
applicability of [RFC3947] in the context of this solution.
Indeed,[RFC3947] (Section 4, Changing to New Ports), specifies that
if an IKE peer responder is behind a port translating NAT, the
initiator is allowed to use a different port than 4500 to contact it.
The initiator will have to determine which ports to use by contacting
another server or by out of band procedure . Once the initiator
knows which ports to use to traverse the NAT, generally something
like UDP (4500, Z), it initiates using these ports.
In the case both IKE initiator and responder peers are behind a Port
translating NAT, the changing port can be summarized as follows:
Init addr CPE Pub1. addr PRR_CPE Pub. addr Resp. addr
v v v v PRR v
Initiator ---------->CPE-----------------> PRR ---------->CPE----------->Responder
^ NAT ^ ^ NAT ^
| | | |
Init addr, PRR_CPE.Pub addr UDP(4500,Z) | | CPE Pub1 addr, Resp.addr (1234,4500)
| |
CPE Pub1 addr, PRR_CPE.Pub addr UDP(1234,Z)
12. ICMP and Other Portless Protocols
The multiplexing of IP flows in PRR is based on the port numbers used
by transport layer protocols such as TCP, UDP, SCTP, and DCCP.
However, the protocols not containing port numbers need special
handling in order to be multiplexed correctly.
As for ICMP messages, identifier field may be used as port number.
The value of this field should be selected from the assigned port
range value. This approach has a limit when both the source and
destination are assigned with a shared IP address.
13. 6to4
A host utilizing 6to4 [RFC3056] with port restricted IPv4 addresses
must pick the 16-bit "SLA ID" value for the 6to4 prefix(es)
construction from the pool of allocated port values. The
Boucadair, et al. Expires January 4, 2010 [Page 25]
Internet-Draft Port Range Architecture July 2009
multiplexing gateway must then multiplex 6to4 traffic based on "SLA
ID" value as it would multiplex plain IPv4 traffic based on port
values. i.e., for incoming packets the gateway shall look at the
destination IPv4 address and the "SLA ID"-field from tunneled IPv6
packet's destination IPv6 address, and then select the right route as
it would have picked the port number from a transport layer header.
14. Protocols not supported by PRR
The case where Port Range Router is not able to multiplex a protocol
is similar to a case where middle box, such as firewall or NAT,
blocks traffic it is not able or willing to pass trough. The
application is recommended to fallback to UDP encapsulation often
used for NAT traversal, for which gateway is able to perform
multiplexing.
15. Comparison with CG-NAT/LSN
15.1. Generic Hurdles and Focus on Transparency to applications which
enclose IPv4 address in their protocol messages
When deploying a Double NAT scenario, several hurdles will be
encountered by Service Providers. Examples of these hurdles are as
follows:
o End-users won't be able to configure their own port forwarding
policies anymore, whilst with the Port Range solution, the user
can still configure port forwarding (provided the port is within
the allowed range).
o Need to activate a second ALG (Application Level Gateway) at the
core network for some applications (e.g., SIP (Session Initiation
Protocol, [RFC3261]);
o Problems to run servers behind middleboxes with private addresses;
o Complication to enable inbound access;
o Performance issues (e.g., maintaining NAT entries by frequent
(every 30s for instance) keep-alive messages is a real killer for
battery powered devices);
o Interference between the service and network layers: The delivery
of some services (e.g., SIP, DNS (Domain Name Service, [RFC1034]),
and FTP (File Transfer Protocol, [RFC3659])) will require the
knowledge of the underlying network engineering characteristics
Boucadair, et al. Expires January 4, 2010 [Page 26]
Internet-Draft Port Range Architecture July 2009
(i.e., Presence of intermediate CG-NAT boxes). If distinct
administrative entities are managing the high-level services and
the underlying IP infrastructure, critical problems for the
current Internet business model will be raised.
Besides these generic hurdles, let's consider the ones that may arise
when delivering SIP-based calls in the presence of CG-NAT boxes.
Concretely, the following constraints should be followed:
o The SIP-based Service Provider should be aware about the
underlying IP infrastructure so as to implement appropriate ALGs
(Application Level Gateway). At least two modifications of SIP
messages should be applied: The first one at the Home NAT and the
second one at the CG-NAT. If no such ALG is enabled, no
communication may be established. This constraint is heavy since
it assumes that the same administrative entity administers both
service and network infrastructures.
o NAT mapping entries at the CG-NAT should be maintained by keep-
alive packets so as to be able to deliver incoming messages to
customers' devices located behind the CG-NAT.
o Media flows may encounter some problems to be delivered since RTP
(Real Time Transport Protocol, [RFC1889]) ports may not be opened.
The introduction of CG-NAT nodes may impact heavily the delivery of
SIP-based services.
With a Port Range approach, nothing is changed with regard to the
behavior of a today CPE with NAT: a SIP ALG can be quite easily
implemented to take care of swapping the embedded IP address and port
number in the messages to reflect the outbound IPv4 address and port
of the CPE. On the contrary, running a SIP ALG instance inside the
Carrier-Grade NAT for each SIP client may turn out to be very
complex. Therefore, with the Port Range approach, SIP-based services
are not altered compared to current practices when a CG-NAT is
present in the path. The same mechanisms as today have to be
deployed without any additional constraint nor impact.
Consequently, SIP-based services are not altered and complexity not
increased.
15.2. Focus on Legal Storage
Most National Regulatory Authorities (NRA) require that ISPs provide
the identity of a customer upon request of the authorities. This
requirement is usually denoted as Legal Storage. In order to
implement this requirement, Service Providers have deployed
Boucadair, et al. Expires January 4, 2010 [Page 27]
Internet-Draft Port Range Architecture July 2009
appropriate infrastructures including memory storage and interface to
their Information Systems. Due to the continuous increase of traffic
exchanged between end users, the amount of data stored by Service
Providers would be also impacted if data relevant to all the sessions
were to be stored. This is considered as a critical issue by Service
Providers.
When deploying a new IP architecture or when modifying the currently
deployed ones, Service Providers should be able to assess its impact
on their Legal Storage infrastructures. Concretely, and because of
the presence of NAPT function the knowledge of the source port number
(simply referred to as port number), along with the source public IP
address (simply referred to as public IP address), is mandatory to be
able to retrieve the appropriate customer (or user) which is
concerned by a given flow. This implies that all NAT mapping
information is to be stored by a given ISP during the whole legal
duration (one year in many countries).
Concretely, and because of the presence of NAPT function (in the CG-
NAT), the knowledge of the source port number (simply referred to as
port number), along with the source public IP address (simply
referred to as public IP address), is mandatory to be able to
retrieve the appropriate customer (or user) which is concerned by a
given flow. This implies that all NAT mapping information is to be
stored by a given ISP during the whole legal duration (one year in
many countries).
When a CG-NAT is deployed, a given Service Provider must store legal
information of the mapped addresses in form of the following tuple:
{Public IP address - Public Port - Private IP address - Private port
- protocol - date and hour of the beginning of address/port
allocation - duration of this allocation (or date and hour of the
allocation end)}.
Note that to actually find the identity of the appropriate customer
which is concerned by a given IP flow, a given ISP must also store
the mapping between the private IP address and the customer
identification.
As for the Port Range based approach, the required information to be
stored is the following tuple (called in the remaining part tuple
with Port Range):
{Public IP address - Port Range - protocol - customer identification
- date and hour of the beginning of the Public IP address and Port
Range allocation - duration of this allocation (or date and hour of
the allocation end)}.
Boucadair, et al. Expires January 4, 2010 [Page 28]
Internet-Draft Port Range Architecture July 2009
The length of this tuple with Port Range is about:
4 + 3 (2 for the Port Range pattern + 1 for the length) + 20
(customer identification) + 8 (date/time begin) + 8 (date/time end) =
43 bytes.
The Port Range is expected to be allocated for the same duration as
the IP address, namely for a reasonable term (e.g., more than 24
hours conforming to current practices of IP address assignment).
Thus, with regard to the nowadays situation, the additive information
to be stored is only the Port Range.
The allocation of Public IP address and Port Range is expected to be
made for a reasonable term (e.g., more than 24 hours) as the current
practices for the assignment of IP addresses.
In order to illustrate the volume of required data to be stored by
Service Providers,let's consider the following figures:
o 1000 CPEs
o 100 new sessions per 10 minutes per CPE (optimistic, it may be
more)
o each CPE traffics during 6 hour a day
o the public address and Ports Range change each day (changing these
parameters may be even less frequent)
The amount of data to be stored per month when the Port Range
approach is enabled (i.e., use of a Port Range) is around 1,3 Mbytes.
The one for CG-NAT is around 3,1 Gbytes (Gbytes and not Mbytes) per
month.
- Port Range based architecture:
Amount for 1000 CPEs per month = 1000 (CPEs) * 43 (bytes for the
tuple with Port Range) * 30 (days in a month) = 1,3 Mbytes
-CG-NAT:
{Public IP address - Public Port - Private IP address - Private port
- protocol - date and hour of the beginning of address/port
allocation - duration of this allocation (or date and hour of the
allocation end)}
= 4 + 2 + + 4 + 2 + 1 + 8 + 8
Boucadair, et al. Expires January 4, 2010 [Page 29]
Internet-Draft Port Range Architecture July 2009
= 29 bytes.
Note : Storing the customer identification attached to the private
address is considered negligible in the calculation.
Amount for 1000 CPEs per month
= 1000 (CPEs) * 100 (number of new sessions in 10 mn) * 36 (number of
10 mn durations in 6 h) * 29 (number of bytes per session) * 30 (days
in a month)
= 3,1 Gbytes
Based on this data, a factor of more than 1000 is to be observed
between the two solutions (in favor of the Port Range approach).
This factor (i.e., ratio of 1000) is important to be taken into
account since CAPEX and OPEX would be impacted drastically for the
implementation of this legal requirement. Indeed, a large investment
must be forecast(ed) for deploying a suitable infrastructure (e.g.,
physical nodes and storage capacity). Service Providers should
carefully consider this impact on their legal storage
infrastructures.
This factor may be optimized if a port ranges are assigned to
customers on the CG-NAT device.
Moreover, as the deployment of the FTTH (Fiber To The Home) will
progress it is expected that the number of sessions per user will be
growing which will further increase the amount of data to be stored
in CG-NAT but not in the Port Range approach.
15.3. Session Handling in CG-NAT
The complexity of the real-time processing is related to the number
of operations to handle the TCP and UDP sessions and associated
complexity.
CG-NAT is a NAT and therefore has to monitor dynamically all the
sessions in order to identify if a public port number is still in-use
or can be released. For this purpose, a CG-NAT needs in particular
to handle timeouts and to scrutinize all TCP session states. In
addition the entries enclosed in the NAT table maintained by a given
CG-NAT is of a much greater complexity than the table in the PRR.
The CG-NAT needs to keep all the mappings [Public IP address - Public
Port - protocol - Private IP address - Private Port] for each session
(UDP or TCP) whilst the PRR has to keep only one entry [Public IP
address - Port Range - route to the CPE] per CPE.
Boucadair, et al. Expires January 4, 2010 [Page 30]
Internet-Draft Port Range Architecture July 2009
For example, if the CPE handles 100 active sessions, the factor is
100 between a CG-NAT and a PRR. For a CPE with 1000 active sessions
(which may not be so rare for clients making high use of peer to peer
applications) the factor raises to 1000. Again, this is not simply a
matter of factor; with CG-NAT, handling a session is complex as
already indicated (e.g., timeouts, scrutinizing of session states,
NAT entries real time maintenance, etc.).
As for the PRR, it does not handle sessions but simply routes packets
(routing based on both IP address and Port Range).
CG-NAT can either be used in a context where the CPE keeps its NAT
(yielding a double NAT configuration) or in a configuration where the
CPE is a mere router (or bridge) without any NAT. In the first case
(i.e., CPE without NAT) there is only one level of NAT in the path
(at the CG-NAT level). All the complexity, today distributed among
the CPEs, becomes concentrated into CG-NAT equipment. The cost of
the CG-NAT is not balanced by a relative simplification of the CPEs
(no NAT embedded). In a double NAT configuration the relative
simplification of the CPE (no NAT embedded) is not even attained.
15.4. Peer-to-Peer applications
P2P applications can not work at full capabilities when a CG-NAT is
in the path. This is because the peers can not initiate
communications toward a peer behind a CG-NAT. Consequently the
communications must pass through a server which greatly reduces the
throughput capabilities of the system. A palliative could be for P2P
applications to use a STUN server so that they can know the public
address and port allocated by the CG-NAT and to keep alive the port
(by periodical short messages).
There is no such problem with the Port Range approach where the user
can still as today set manually the port forwarding policies onto his
CPE (e.g., Through WEB page, provided the choice of the port were
restricted to the allocated Port Range, etc.).
16. IANA Considerations
TBC.
17. Security Considerations
This section will be completed in the next version of this draft.
Boucadair, et al. Expires January 4, 2010 [Page 31]
Internet-Draft Port Range Architecture July 2009
18. Contributors
These authors have contributed to this memo:
o Jean-Luc Grimault (France Telecom,
jeanluc.grimault@orange-ftgroup.com)
o Alain Villefranque (France Telecom,
alain.villefranque@orange-ftgroup.com )
19. Acknowledgements
The authors would like to thank Dave THALER and Yoann NOISETTE, for
their extensive review and technical input, and Mohammed KASSI LAHLOU
for his suggestion regarding the involvement of the DHCP client
relay. We would also like to thank Pierrick MORAND and Mohammed
ACHEMLAL for their support and suggestions.
6to4 text has been proposed by D. THALER.
20. References
20.1. Normative References
[RFC1034] Mockapetris, P., "Domain names - concepts and facilities",
STD 13, RFC 1034, November 1987.
[RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
November 1990.
[RFC1584] Moy, J., "Multicast Extensions to OSPF", RFC 1584,
March 1994.
[RFC1661] Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51,
RFC 1661, July 1994.
[RFC1858] Ziemba, G., Reed, D., and P. Traina, "Security
Considerations for IP Fragment Filtering", RFC 1858,
October 1995.
[RFC1889] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", RFC 1889, January 1996.
[RFC2026] Bradner, S., "The Internet Standards Process -- Revision
3", BCP 9, RFC 2026, October 1996.
Boucadair, et al. Expires January 4, 2010 [Page 32]
Internet-Draft Port Range Architecture July 2009
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol",
RFC 2131, March 1997.
[RFC3376] Cain, B., Deering, S., Kouvelas, I., Fenner, B., and A.
Thyagarajan, "Internet Group Management Protocol, Version
3", RFC 3376, October 2002.
20.2. Informative References
[I-D.bajko-pripaddrassign]
Bajko, G., Savolainen, T., Boucadair, M., and P. Levis,
"Port Restricted IP Address Assignment",
draft-bajko-pripaddrassign-01 (work in progress),
March 2009.
[I-D.boucadair-behave-ipv6-portrange]
Boucadair, M., Levis, P., Grimault, J., Villefranque, A.,
and M. Kassi-Lahlou, "Flexible IPv6 Migration Scenarios in
the Context of IPv4 Address Shortage",
draft-boucadair-behave-ipv6-portrange-01 (work in
progress), March 2009.
[I-D.boucadair-pppext-portrange-option]
Boucadair, M., Levis, P., Grimault, J., and A.
Villefranque, "Port Range Configuration Options for PPP
IPCP", draft-boucadair-pppext-portrange-option-00 (work in
progress), February 2009.
[I-D.fuller-240space]
Fuller, V., "Reclassifying 240/4 as usable unicast address
space", draft-fuller-240space-02 (work in progress),
March 2008.
[I-D.ietf-softwire-dual-stack-lite]
Durand, A., Droms, R., Haberman, B., and J. Woodyatt,
"Dual-stack lite broadband deployments post IPv4
exhaustion", draft-ietf-softwire-dual-stack-lite-00 (work
in progress), March 2009.
[I-D.savolainen-indicating-240-addresses]
Savolainen, T., "A way for a host to indicate support for
240.0.0.0/4 addresses",
draft-savolainen-indicating-240-addresses-01 (work in
progress), February 2009.
Boucadair, et al. Expires January 4, 2010 [Page 33]
Internet-Draft Port Range Architecture July 2009
[RFC2236] Fenner, W., "Internet Group Management Protocol, Version
2", RFC 2236, November 1997.
[RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains
via IPv4 Clouds", RFC 3056, February 2001.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC3659] Hethmon, P., "Extensions to FTP", RFC 3659, March 2007.
[RFC3715] Aboba, B. and W. Dixon, "IPsec-Network Address Translation
(NAT) Compatibility Requirements", RFC 3715, March 2004.
[RFC3947] Kivinen, T., Swander, B., Huttunen, A., and V. Volpe,
"Negotiation of NAT-Traversal in the IKE", RFC 3947,
January 2005.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)", RFC 4601, August 2006.
Authors' Addresses
Mohamed Boucadair (editor)
France Telecom
3, Av Francois Chateau
Rennes 35000
France
Email: mohamed.boucadair@orange-ftgroup.com
Pierre Levis
France Telecom
42 rue des Coutures
BP 6243
Caen Cedex 4 14066
France
Email: pierre.levis@orange-ftgroup.com
Boucadair, et al. Expires January 4, 2010 [Page 34]
Internet-Draft Port Range Architecture July 2009
Gabor Bajko
Nokia
Email: gabor.bajko@nokia.com
Teemu Savolainen
Nokia
Hermiankatu 12 D
FI-33720 TAMPERE
Finland
Email: teemu.Savolainen@nokia.com
Boucadair, et al. Expires January 4, 2010 [Page 35]