TICTOC S. Bryant
Internet-Draft Cisco Systems
Intended status: Informational Y(J). Stein
Expires: October 11, 2008 RAD Data Communications
April 9, 2008
TICTOC Problem Statement
draft-bryant-tictoc-probstat-02.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on October 11, 2008.
Copyright Notice
Copyright (C) The IETF Trust (2008).
Abstract
This Internet draft describes a number of applications that require
accurate time and/or frequency, and elucidates difficulties related
to the transfer of high quality time and frequency across an IP or
MPLS Packet Switched Network. This issue is not addressed by any
currently chartered IETF working group, and we therefore propose the
formation of a new working group to be called Transmitting Timing
over IP Connections and Transfer of Clock (TICTOC).
Bryant & Stein Expires October 11, 2008 [Page 1]
Internet-Draft TICTOC April 2008
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Applications . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Time Service Applications . . . . . . . . . . . . . . . . 3
2.2. Frequency Service Applications . . . . . . . . . . . . . . 4
3. Existing Time and Frequency Transfer Mechanisms . . . . . . . 7
3.1. Radio-based Timing Transfer Methods . . . . . . . . . . . 7
3.2. Dedicated Wire-based Timing Transfer Methods . . . . . . . 8
3.3. Transfer Using Packet Networks . . . . . . . . . . . . . . 9
3.3.1. The Packet Network Environment . . . . . . . . . . . . 11
4. Problems with Existing Solutions . . . . . . . . . . . . . . . 11
5. Other Forums Working in this Problem Space . . . . . . . . . . 12
6. Security Considerations . . . . . . . . . . . . . . . . . . . 13
7. Security Considerations . . . . . . . . . . . . . . . . . . . 13
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 14
10. Informative References . . . . . . . . . . . . . . . . . . . . 14
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 14
Intellectual Property and Copyright Statements . . . . . . . . . . 16
Bryant & Stein Expires October 11, 2008 [Page 2]
Internet-Draft TICTOC April 2008
1. Introduction
There is an emerging need to distribute highly accurate time and
frequency information over IP and over MPLS packet switched networks
(PSNs). In this problem statement we give several examples of
applications that require time and/or frequency information, and
explain why their needs can not be satisfied by time/frequency
transfer over PSNs using existing protocols. We review these
existing protocols and the work being carried out in the IETF and in
other forums. Finally, we list the objectives of a proposed Working
Group.
2. Applications
2.1. Time Service Applications
There are many applications that need to know the time with greater
precision than provided by available mechanisms, such as the current
version of NTP [RFC1305]. These applications span a range of
industries: telecommunications, financial, test and measurement,
government, industrial etc. Preliminary studies indicate that the
availability of high accuracy time as a commodity enables use of
techniques that were previously considered impossible. We can,
therefore, expect that the provision of high quality time through the
network infrastructure will generate a spiral of new innovative
applications that will in turn make greater demands on the quality of
time delivered to the end-user.
The best-known example of an application that requires high quality
time in the telecommunications sector is the need to measure one-way
packet delay. Current implementations of NTP have accuracy of the
order of 10 milliseconds. When NTP is used to characterize packet
delay and packet delay variation, such a time-base cannot resolve any
two party event with a resolution of better than 20 milliseconds.
Contrast this with the characteristics of a 10 Gb/s link, 1 kilometer
long. On such a link, a minimum sized packet takes 50 nanoseconds to
send, and it takes 6 microseconds to traverse the link. The
performance of current NTP implementations is orders of magnitude
worse than the duration of network forwarding events, and clearly
insufficient to characterize them.
Although the measurement of the characteristics of a packet network
is the best-known telecommunications example, there are other
operational needs, notably synchronization at the MAC layer. The
cable industry has recently defined a new intra-PoP time transmission
mechanism for just this purpose (DOCSYS Timing Interface), and WiMAX
is looking for relative time delivery to its transmitter sites.
Bryant & Stein Expires October 11, 2008 [Page 3]
Internet-Draft TICTOC April 2008
In the test and measurement and industrial sector there is a desire
to move from special purpose communications infrastructure with
calibrated wiring run back to a centralize controller, to a
distributed system, in which instructions are distributed in advance
to be executed at a predetermined time, and in which measurements are
taken remotely and communicated back to a common point for later
correlation and analysis. Two examples of this tendency are
described below.
In the printing industry there is a need to control operations in
multi-stand printing machines. The paper travels through these
machines at a speed of nearly 100 km/h. At these speeds, co-
ordination error of 1 microsecond between operations taking place at
different positions in the machine produces a 0.03mm color offset,
which is visible to the naked eye and results in an unacceptable
degradation in quality.
In the electrical power industry there is a need to improve the
measurement of power flows in order to monitor and predict usage
patterns. One proposal is to extensively deploy synchro-phasors in
the power network and to correlate their output to determine demand.
These devices need to be able to determine the time of measurement
with an accuracy of 1 microsecond.
More generally, there is growing interest in clock synchronization in
massively parallel sensor networks. Advances in wireless
communications have enabled the development of low power miniature
sensors that collect and disseminate data from their immediate
environment. Although each sensor has limited processing power,
through distributed processing the network becomes capable of
performing various tasks of data fusion, but only assuming a common
time base can be established.
The examples cited above are a small illustration of a trend that
will continue to grow as designers realize that better scaling can be
achieved with action-in-the-future, measure-and-correlate-later
approaches to systems design.
Closer to the core interests and expertise of the IETF there is an
emerging opinion that the availability of time as a commodity may
simplify the protocols that we use in distributed systems.
2.2. Frequency Service Applications
There are applications that require time with a greater precision
than can easily be provided using available mechanisms. Cellular
base-stations require a highly accurate frequency reference from
which they derive transmission frequencies and operational timing.
Bryant & Stein Expires October 11, 2008 [Page 4]
Internet-Draft TICTOC April 2008
Conventionally GSM and WCDMA base stations obtain this reference
frequency by locking on to the E1/T1 that links them to the base
station controller. With the replacement of TDM links with Packet
Switched Networks (PSNs) such as Ethernet, IP or MPLS, this simple
method of providing a frequency reference is lost, and frequency
information must be made available in some other way.
Why must the frequency reference be so accurate? First and foremost
the requirement is derived from the need for the radio frequencies to
be accurate. Radio spectrum is a limited and valuable commodity that
needs to be used as efficiently as possible. In GSM, transmission
frequencies are allocated to a given cellular base station and its
neighbors in such fashion as to ensure that they do not interfere
with each other. If the radio network designer cannot rely on the
accuracy of these frequencies, the spacing between the frequencies
used by neighboring sites must be increased, with significant
economic consequences.
There is an additional requirement derived from the need for smooth
handover when a mobile station crosses from one cell to another. If
the radio system designer can not guarantee that the preparations
required for handover occur in a few milliseconds, then they must
allow the mobile station to consume frequency resources
simultaneously in both cells in order to avoid service disruption.
The preparations required involve agreement between the mobile and
base stations on the new frequencies and time offsets; these
agreements can be accomplished quickly when the two base stations'
frequency references are the same to a high degree of accuracy.
Another application requiring highly accurate frequency distribution
is TDM pseudowires. The PWE3 WG has produced three techniques for
emulating traditional low-rate (E1, T1, E3, T3) TDM services over
PSNs, namely SAToP [RFC4553], CESoPSN, and TDMoIP. The major
technical barrier to universal acceptance of TDM pseudowires is the
accuracy of its clock recovery.
TDM network standards for timing accuracy and stability are extremely
demanding. These requirements are not capriciously dictated by
standards bodies, rather they are critical to the proper functioning
of a high-speed TDM network. Consider a TDM receiver utilizing its
own clock when converting the physical signal back into a bit-stream.
If the receive clock runs at precisely the same rate as the source
clock, then the receiver need only determine the optimal sampling
phase. However, with any mismatch of clock rates, no matter how
small, bit slips will eventually occur. For example, if the receive
clock is slower than the source clock by one part per million (ppm),
then the receiver will output 999,999 bits for every 1,000,000 bits
sent, thus deleting one bit. Similarly, if the receive clock is
Bryant & Stein Expires October 11, 2008 [Page 5]
Internet-Draft TICTOC April 2008
faster than the source clock by one part per billion (ppb), the
receiver will insert a spurious bit every billion bits. One bit slip
every million bits may seem acceptable at first glance, but
translates to a catastrophic two errors per second for a 2 Mb/s E1
signal. ITU-T recommendations permit a few bit slips per day for a
low-rate 64 kb/s channel, but strive to prohibit bit slips entirely
for higher-rate TDM signals.
In certain cases, such as "toll-bypass" or "carrier's carrier" links,
the endpoints of the TDM PW are full TDM networks, and timing may
(indeed must) be derived from the respective network clocks. Since
each of these clocks is highly accurate, they necessarily agree to
high order. However, TDM PWs are expected to increasingly replace
native TDM links delivering services from core networks towards
users, and here there is no alternative to provision of accurate
frequency information.
In this context there are two types of frequency distribution being
studied. In the first type the frequency reference used by the TDM
source is distributed downstream, as in the native TDM service. In
the "common clock" scenario highly accurate frequency information is
distributed from a central server to both ends of the emulated TDM
link. By placing in the protocol overhead timestamps based on the
common clock, the receiver can accurately recover the TDM source
clock.
While it is true that services designed for PSN (e.g. VoIP)
transport are less dependent on frequency accuracy, there are still
cases where such services need accurate frequency distribution. For
example, when interconnecting tradition telephones via VoIP links,
users expect these links to support legacy services, such as
facsimile and dial-up data modems. The optimal technique for
supporting these services is by provision of relay functions, e.g.
T.38 fax-relay and V.150 modem-relay, that terminate the analog
transmissions on both sides and transfer data content over the PSN.
However, provision of relay services is computationally expensive,
often requires expensive DSP-capable media gateways, and can only
support known modem types. In many deployments old fax machines or
proprietary data modems or secure voice telephones are used, and the
modulations and handshake protocols are not recognized by the relays
provided. In such cases the solution is to carry these transmissions
over "clear channel" or Voice Band Data (VBD), i.e. to send raw
samples of the audio in packets over the PSN.
The problem with clear channel transfer of data over PSNs is that the
end points expect a non-intrusive analog channel between them, over
which they implicitly transfer timing information. The receiver can
thus continually lock onto the transmitter's frequency, and the
Bryant & Stein Expires October 11, 2008 [Page 6]
Internet-Draft TICTOC April 2008
transmission can continue for an unlimited period without
interruption. When employing clear channel, the frequency signal
seen by the receiver is influenced by the destination gateway's clock
used to convert the data samples back to analog form. If the source
and destination gateways' clocks do not agree to a high degree of
accuracy, the receiver does not properly lock onto the transmitter's
clock, leading to disruption of the data reception. In typical cases
a modem conversation transferred over clear channel may drop after
only several minutes, and fax reception may be interrupted after
several pages have been received.
3. Existing Time and Frequency Transfer Mechanisms
In this section we will discuss existing mechanisms for transfer of
time information, frequency information, or both. It should be noted
that a sufficiently accurate time transfer service may be used to
derive an accurate frequency transfer. Indeed, this is exactly what
happens in a GPS disciplined frequency standard. On the other hand,
an accurate frequency transfer service, while itself unable to
transfer absolute time, is usually used to support and improve the
performance of the time transfer service. Indeed, implementations of
NTP or IEEE 1588 clients can be considered to consist of two phases.
First, a local oscillator is locked to the server's frequency using
incoming information from the incoming packets, and then the local
time set based on the server's time and the propagation latency. By
maintaining a local frequency source, the client requires relatively
infrequent updates, and can continue functioning during short periods
of network outage. Moreover, it can be shown that this method
results in significantly better time transfer accuracy than methods
that do not discipline a local clock.
Time transfer mechanisms can be divided into three classes. The
first class consists of mechanisms that use radio frequency
transport, while the second mechanism uses dedicated "wires" (which
for our purposes include optical fibers). The third, which will be
our main focus, exploits a Packet Switched Network for transfer of
timing information. Advantages and disadvantages of these three
methods are discussed in the following subsections.
3.1. Radio-based Timing Transfer Methods
The transfer of time by radio transmission is one of the oldest
methods available, and is still the most accurate wide area method.
In particular, there are two navigation in wide use that can be used
for time transfer, The LOng RAnge Navigation (LORAN) terrestrial
radio system, and the Global Navigation Satellite System (GNSS). In
both cases the user needs to be able to receive the transmitted
Bryant & Stein Expires October 11, 2008 [Page 7]
Internet-Draft TICTOC April 2008
signal, requiring access to a suitable antenna. In certain
situations, e.g. basement communications rooms and urban canyons, the
required signal may not be receivable.
Radio systems have high accuracy, far better than what we will later
see can be achieved by existing PSN technologies. However coverage
is limited; eLORAN for example only covers North America, and GPS
does not have good coverage near the poles.
Although civilian use is sanctioned, the GPS was developed and is
operated by the U.S. Department of Defense as a military system. For
this reason there are political concerns that rules out its use in
certain countries. The European Union is working on an alternative
system called Galileo, which will be run as a commercial enterprise.
In addition, GPS has some well-documented multi-hour outages, and is
considered vulnerable to jamming. One major PTT also reports that
they see a 2% per year failure rate for the antenna/receiver/
clock-out chain.
While a radio-based timing service may be acceptable for some sites,
it is frequently impractical to use on a per equipment basis. Hence,
some form of local timing distribution is usually also required.
3.2. Dedicated Wire-based Timing Transfer Methods
The use of dedicated networks in the wide area does not scale well.
Such services were available in the past, but for reasons of cost and
accuracy have been superseded by GPS based solutions.
In the local area, one new technique is emerging as a mechanism for
time transport, namely DOCSIS Timing Interface / Telecommunications
Timing Interface (DTI/TTI). DTI was designed by DOCSIS for the
distribution of time in a cable head-end in support of media access
control. Time transfer is packet-based over a multi-stage hub and
spoke dedicated network. It uses a single twisted-pair in half-
duplex to eliminate inaccuracies due to the length differences
between the pairs in a multi-pair cable. TTI is a development of DTI
designed to provide synchronization in a telephone local office.
Accuracy for DTI is better than 5 nanoseconds and range is 100 feet
for DTI. This increases to 600 feet for TTI at some reduction in
packet rate and hence time quality.
The DTI/TTI approach is applicable for special applications, but the
need for a dedicated network imposes significant drawbacks for the
general time transfer case.
Synchronous Ethernet is a technique that has recently been proposed
for providing frequency distribution over Ethernet links. Modern
Bryant & Stein Expires October 11, 2008 [Page 8]
Internet-Draft TICTOC April 2008
dedicated-media full-duplex Ethernet, in both copper and optical
physical layer variants, transmits continuously. One can thus elect
to derive the physical layer transmitter clock from a high quality
frequency reference, instead of the conventional 100 ppm crystal-
derived transmitter rate. The receiver at the other end of the link
automatically locks onto the physical layer clock of the received
signal, and thus itself gain access to a highly accurate and stable
frequency reference. Then, in TDM fashion, this receiver could lock
the transmission clock of its other ports to this frequency
reference.
The ITU-T is presently working on a specification for synchronous
Ethernet. Apart from some necessary higher layer packet based
configuration and OAM operations, the solution is entirely physical
layer, and has no impact on higher layers.
At first sight it would seem that the only application of synchronous
Ethernet was in frequency transfer (it has no intrinsic time transfer
mechanism). However, the quality of packet-based time transfer
mechanism can be considerably enhanced if used in conjunction with
synchronous Ethernet as a frequency reference.
3.3. Transfer Using Packet Networks
When using a PSN to transfer timing, a server sends timing
information in the form of packets to one or multiple clients. When
there are multiple clients, the timing packets may be multicast.
Software in the client recovers the frequency and/or time of the
server based on the packet arrival time and the packet contents.
There are two well-known protocols capable of running over a general-
purpose packet network, NTP [RFC1305], and IEEE 1588 [1588]. NTP is
the product of the IETF, and is currently undergoing revision to
version 4. IEEE 1588 (a product of the IEEE Test and Measurement
community) is specified in a limited first version, and the second
version (1588v2)is in the detailed design stage.
NTP is widely deployed, but existing implementations deliver accuracy
on the order of 10 milliseconds. This accuracy is not adequate for
the applications described above. NTP suffers from the fact that it
was designed to operate over the Internet, and the routers and
switches used in the best effort Internet make no special concessions
to NTP for preservation of time transfer accuracy. Furthermore,
typical update rates are low and can not be significantly increased
due to scalability issues in the server. In addition most NTP time
servers and time receivers have a relatively unsophisticated
implementation that further degrades the final time quality.
Bryant & Stein Expires October 11, 2008 [Page 9]
Internet-Draft TICTOC April 2008
IEEE 1588v1 was a time transfer protocol that exclusively used a
fairly crude multicast technique. It is widely anticipated that wide
scale deployment of IEEE1588 will be based on 1588v2. The
information exchange component of IEEE 1588 is a protocol known as
Precision Time Protocol (PTP).
IEEE 1588v2 can be considered to consist of several components:
1. A configuration and control protocol
2. A time transfer protocol
3. A time correction protocol
4. Physical mapping
The configuration and control protocol is based on the multicast
approach of IEEE 1588v1 (multicast IP with recommended TTL=1, UDP,
IEEE1588 payload with equipment identifier in the payload). The
rationale for this approach was that the equipment needed to be "plug
and play" (no configuration), was required to map to physical media
other than Ethernet, and had to have a very low memory and processor
footprint.
The time transfer protocol is a standard two-way time transfer
approach used in other packet-based approaches. Like all such
approaches it is subject to inaccuracies due to variable store and
forward delays in the packet switches, and due to the assumption of
symmetric propagation delays. The time transfer packets (in both
directions) may be operated in a multicast or unicast mode.
The time correction protocol is used to correct for propagation,
store and forward delays in the packet switches. This again may be
operated multicast or unicast. This mechanism requires some level of
hop-by-hop hardware support. This mechanism may also be considered a
concept in its own right and may be adapted to enhance other packet
time transfer protocols such as NTP.
The base 1588 specification describes how the PTP operates over the
Ethernet/IP/UDP protocol stack. Annexes are planned that describe
PTP operation over pure layer 2 Ethernet, over IP without UDP, over
MPLS, and over a number of specialist media.
The mappings of interest for telecommunications are PTP over UDP/IP,
PTP over MPLS , and perhaps PTP over Ethernet, all in unicast mode
only. Issues of a suitable control management and OAM environment
for these applications are largely in abeyance, as are considerations
about the exact nature of the network environment.
Bryant & Stein Expires October 11, 2008 [Page 10]
Internet-Draft TICTOC April 2008
It is also worth noting the existence of a second IEEE effort, IEEE
802.1AS. This group is specifying the protocol and procedures to
ensure synchronization across Bridged and Virtual Bridged Local Area
Networks for time sensitive applications such as audio and video.
For these LAN media the transmission delays are assumed to be fixed
and symmetrical. IEEE 802.1AS specifies the use of IEEE 1588
specifications where applicable in the context of IEEE Standards
802.1D and 802.1Q. Synchronization to an externally provided timing
signal (e.g., a recognized timing standard such as UTC or TAI) is not
part of this standard but is not precluded. IEEE 802.1AS will
specify how stations attached to bridged LANs to meet the respective
jitter, wander, and time synchronization requirements for time-
sensitive applications.
3.3.1. The Packet Network Environment
Packet delay variation, propagation asymmetry, and maximum
permissible packet rate all have a significant bearing on the
accuracy with which the client is able to determine absolute time.
Thus the network environment has a large bearing on the quality of
time that can be delivered.
Packet delay variation can to some extent be addressed by traffic
engineering, thus time transfer with a service provider network in
which suitable traffic engineering techniques had been applied might
reasonably be expected to deliver a higher quality time service than
can be achieved between two arbitrary hosts connected to the
Internet. Greater gains can probably be obtained by deploying
equipment that incorporates IEEE 1588 style on-the-fly packet
timestamp correction, or follow-up message mechanisms that report the
packet storage and forward delays to the client. However one can
only be sure that such techniques are available along the entire path
in a well-controlled environment.
The packet rate between the time-server and its client also has a
bearing on the quality of the time transfer, because at a higher rate
the smart filter has a better chance of extracting the "good"
packets. In a controlled environment it is possible to ensure that
there is adequate bandwidth, and that the server is not overloaded.
In such an environment the onus moves from protecting the server from
overload, to ensuring that the server can satisfy the needs of all of
the clients.
4. Problems with Existing Solutions
An obvious candidate for clock distribution is NTP or some upgrade
thereof. While the time resolution provided by NTP is extremely
Bryant & Stein Expires October 11, 2008 [Page 11]
Internet-Draft TICTOC April 2008
good, the accuracy attainable by existing NTP implementations does
not satisfy the needs of the most demanding of the applications,
mainly due to update rate and the particular client/server method
employed.
The new IEEE 1588v2 protocol also addresses these needs, but has been
largely designed around a well-controlled LAN environment. A 1588
server in unicast mode needs to save state information for each
client, a solution that does not scale well to deployment sizes
envisioned. In addition, 1588 specifies hardware upgrades in order
to perform well in an IP network.
Synchronous Ethernet only satisfies the need for frequency
distribution, and even then only over one physical Ethernet link at a
time. In order to use synchronous Ethernet in a network, all network
elements must be upgraded to support synchronous operation at the
physical layer. Even when hardware can be upgraded, only frequency
is delivered, and there is still a need to develop a time transfer
protocol.
5. Other Forums Working in this Problem Space
The NTP WG is the IETF group working on time distribution, but is
presently only documenting NTPv4 and is not working on new algorithms
or protocols. It is expected that many participants of the NTP WG
will participate in the TICTOC effort.
The PWE3 WG has discussed frequency distribution for the TDM PW
application, however it is not chartered to develop protocols for
this purpose. It is expected that participants of the PWE3 WG who
were active in the TDM PW discussions will participate in the TICTOC
effort.
The work that is underway outside the IETF is either complementary to
this proposal, or less general than the proposal proposed by the
TICTOC work proposal.
The IEEE 1588 task force is working on a new version of their
protocol that will run over more types of PSNs, and is planning to
conclude its development work in the near future. The protocol to be
specified contains elements that will be of use in an IETF
environment, but is unlikely to be regarded as being a complete,
robust solution in such an environment. If the IEEE 1588 structure
is deemed to be a suitable platform, then the IETF could contribute
an Internet profile, including a complete distributed systems
environment suitable for our purposes. Alternatively, the IETF could
perhaps borrow some of the delay correction mechanisms and
Bryant & Stein Expires October 11, 2008 [Page 12]
Internet-Draft TICTOC April 2008
incorporate them into a development of a new version of NTP.
In addition, IEEE 802.1AS is working on Timing and Synchronization
for Time-Sensitive Applications in Bridged Local Area Networks,
basing itself on the IEEE 1588 standard.
ITU-T SG15 Question 13 has produced Recommendation G.8261 "Timing and
synchronization aspects in packet networks" [G8261]. This
Recommendation defines requirements for various scenarios, outlines
the functionality of frequency distribution elements, and provides
measurement guidelines. It does not specify algorithms to be used
for attaining the performance needed. It does define requirements
for status synchronization messages, but does not otherwise define a
protocol (although work is in progress). To date the ITU-T has
focused on Ethernet infrastructure, but this is likely to extend to
an MPLS environment. Two new work items, G.paclock and G.pacmod
extend the work, and in particular, G.pacmod intends to introduce
time transfer. This is an area where the IETF, with its expertise in
IP and MPLS networks, may co-operate with the ITU.
6. Security Considerations
Time and frequency services are a significant element of network
infrastructure, and are critical for certain emerging applications.
Hence time and frequency transfer services MUST be protected from
being compromised. The most significant threat is a false time or
frequency server being accepted instead of a true one, thus enabling
a hacker to bring down critical services.
Any protection mechanism must be designed in such a way that it does
not degrade the quality of the time transfer. Such a mechanism
SHOULD also be relatively lightweight, as client restrictions often
dictate a low processing and memory footprint, and because the server
may have extensive fan-out.
7. Security Considerations
Timing distribution is highly sensitive to packet delay, and can thus
can deteriorate under congestion conditions. Furthermore the
disciplining of the client's oscillator (the sole component of
frequency transfer, and a critical component of time transfer) is a
function that should not be disrupted. When the service is disrupted
the client needs to go into "holdover" mode, and its accuracy will
consequently be degraded. Depending on the relative quality of the
client's clock and the required quality after disciplining, a
relatively high packet rate may be required.
Bryant & Stein Expires October 11, 2008 [Page 13]
Internet-Draft TICTOC April 2008
Timing tranfer packets should always be sent using the highest class
of service, and when possible should be sent over a traffic
engineered path.
When the network goes into congestion it should try to avoid
discarding time transfer packets until the situation is critical.
Work performed by the IETF PWE3 WG on congestion would seem to be
applicable to this problem area.
8. IANA Considerations
No IANA actions are required as a result of the publication of this
document.
9. Acknowledgements
The authors wish to thank Laurent Montini for valuable comments.
10. Informative References
[1588] IEEE, "1588-2002 Standard for A Precision Clock
Synchronization Protocol for Networked Measurement and
Control Systems".
[G8261] ITU-T, "Recommendation G.8261/Y.1361 - Timing and
synchronization aspects in packet networks", May 2006.
[RFC1305] Mills, D., "Network Time Protocol (Version 3)
Specification, Implementation", RFC 1305, March 1992.
[RFC4553] Vainshtein, A. and YJ. Stein, "Structure-Agnostic Time
Division Multiplexing (TDM) over Packet (SAToP)",
RFC 4553, June 2006.
Authors' Addresses
Stewart Bryant
Cisco Systems
250 Longwater Ave., Green Park
Reading RG2 6GB
United Kingdom
Email: stbryant@cisco.com
Bryant & Stein Expires October 11, 2008 [Page 14]
Internet-Draft TICTOC April 2008
Yaakov (Jonathan) Stein
RAD Data Communications
24 Raoul Wallenberg St., Bldg C
Tel Aviv 69719
ISRAEL
Phone: +972 3 645-5389
Email: yaakov_s@rad.com
Bryant & Stein Expires October 11, 2008 [Page 15]
Internet-Draft TICTOC April 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Bryant & Stein Expires October 11, 2008 [Page 16]