Network Working Group H. Chen
Internet-Draft China Telecom
Intended status: Experimental Z. Hu
Expires: January 13, 2022 Huawei Technologies
H. Chen
Futurewei
X. Geng
Huawei Technologies
Y. Liu
China Mobile
July 12, 2021
SRv6 Midpoint Protection
draft-chen-rtgwg-srv6-midpoint-protection-05
Abstract
The current local repair mechanism, e.g., TI-LFA, allows local repair
actions on the direct neighbors of the failed node to temporarily
route traffic to the destination. This mechanism could not work
properly when the failure happens in the destination point or the
link connected to the destination. In SRv6 TE, the IPv6 destination
address in the outer IPv6 header could be the dedicated endpoint of
the TE path rather than the destination of the TE path. When the
endpoint fails, local repair couldn't work on the direct neighbor of
the failed endpoint either. This document defines midpoint
protection, which enables the direct neighbor of the failed endpoint
to do the function of the endpoint, replace the IPv6 destination
address to the other endpoint, and choose the next hop based on the
new destination address.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Chen, et al. Expires January 13, 2022 [Page 1]
Internet-Draft SRv6 Midpoint Protection July 2021
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 13, 2022.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. SRv6 Midpoint Protection Mechanism . . . . . . . . . . . . . 3
3. SRv6 Midpoint Protection Example . . . . . . . . . . . . . . 3
4. SRv6 Midpoint Protection Behavior . . . . . . . . . . . . . . 5
4.1. Transit Node as Repair Node . . . . . . . . . . . . . . . 5
4.2. Endpoint Node as Repair Node . . . . . . . . . . . . . . 6
4.3. Endpoint x Node as Repair Node . . . . . . . . . . . . . 6
5. Determining whether the Endpoint could Be Bypassed . . . . . 7
6. Security Considerations . . . . . . . . . . . . . . . . . . . 7
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 8
9.1. Normative References . . . . . . . . . . . . . . . . . . 8
9.2. Informative References . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9
1. Introduction
The current mechanism, e.g., TI-LFA
([I-D.ietf-rtgwg-segment-routing-ti-lfa]), allows local repair
actions on the direct neighbors of the failed node to temporarily
route traffic to the destination. This mechanism could not work
properly when the failure happens in the destination point or the
link connected to the destination. In SRv6 TE, the IPv6 destination
Chen, et al. Expires January 13, 2022 [Page 2]
Internet-Draft SRv6 Midpoint Protection July 2021
address in the outer IPv6 header could be the dedicated endpoint of
the TE path rather than the destination of the TE path ([RFC8986]).
When the endpoint fails, local repair couldn't work on the direct
neighbor of the failed endpoint either. This document defines
midpoint protection, which enables the direct neighbor of the failed
endpoint to do the function of the endpoint, replace the IPv6
destination address to the other endpoint, and choose the next hop
based on the new destination address.
2. SRv6 Midpoint Protection Mechanism
When an endpoint node fails, the packet needs to bypass the failed
endpoint node and be forwarded to the next endpoint node of the
failed endpoint. There are two stages or time periods after an
endpoint node fails. The first is the time period from the failure
until the IGP converges on the failure. The second is the time
period after the IGP converges on the failure.
During the first time period, the packet will be sent to the direct
neighbor of the failed endpoint node. After detecting the failure of
its interface to the failed endpoint node, the neighbor forwards the
packets around the failed endpoint node. It changes the IPv6
destination address with the IPv6 address of the next endpoint node
(or the last or other reasonable endpoint node) which could avoid
going through the failed endpoint.
During the second time period, the packet of a SRv6 TE path may not
be sent to the direct neighbor of the failed endpoint node. There is
no route to the failed endpoint node after the IGP converges. When a
previous hop node of the failed endpoint node finds out that there is
no route to the IPv6 destination address (of the failed endpoint
node), it changes the IPv6 destination address with the IPv6 address
of the next endpoint node. Note that the previous hop node may not
be the direct neighbor of the failed endpoint node.
3. SRv6 Midpoint Protection Example
The topology in Figure 1 illustrates an example of network topology
with SRv6 enabled on each node.
Chen, et al. Expires January 13, 2022 [Page 3]
Internet-Draft SRv6 Midpoint Protection July 2021
+-----+ +-----+
| N5 |-----------| N6 |--------------+
+-----+ +-----+ |
| | |
| | |
| | |
+-----+ +-----+ +-----+ +-----+
| N1 |-----------| N2 |-----------| N3 |-----------| N4 |
+-----+ +-----+ +-----+ +-----+
Figure 1: An example of network for midpoint protection
In this document, an end SID at node n with locator block B is
represented as B:n. An end.x SID at node n towards node k with
locator block B is represented as B:n:k. A SID list is represented
as <S1, S2, S3> where S1 is the first SID to visit, S2 is the second
SID to visit and S3 is the last SID to visit along the SRv6 TE path.
In the reference topology, suppose that Node N1 is an ingress node of
SRv6 TE path going through N3 and N4. Node N1 steers a packet into a
segment list < B:3, B:4>.
When node N3 fails, the packet needs to bypass the failed endpoint
node and be forwarded to the next endpoint node after the failed
endpoint in the TE path. When outbound interface failure happens in
the Repair Node (which is not limited to the previous hop node of the
failed endpoint node), it performs the proxy forwarding as follows:
During the first time period (i.e., before the IGP converges), node
N2 (direct neighbor of N3) as a Repair Node forwards the packets
around the failed endpoint N3 after detecting the failure of the
outbound interface to the endpoint B:3. It changes the IPv6
destination address with the next sid B:4. N2 detects the failure of
outbound interface to B:4 in the current route, it could use the
normal Ti-LFA repair path to forward the packet, because it is not
directly connected to the node N4. N2 encapsulates the packet with
the segment list < B:5:6> as a repair path.
During the second time period (i.e., after the IGP converges), node
N1 does not have any route to the failed endpoint N3 in its FIB.
Node N1, as a Repair Node, forwards the packets around the failed
endpoint N3 to the next endpoint node (e.g., N4) directly. There is
no need to check whether the failed endpoint node is directly
connected to N1. N1 changes the IPv6 destination address with the
next sid B:4. Since IGP has completed convergence, it forwards
packets directly based on the IGP SPF path
Chen, et al. Expires January 13, 2022 [Page 4]
Internet-Draft SRv6 Midpoint Protection July 2021
4. SRv6 Midpoint Protection Behavior
A node N protecting the failure of an endpoint node on a SRv6 path
may be one of the following types:
o a transit node: the destination address (DA) of the packet
received by N is not N's local SID.
o an endpoint node: the destination address (DA) of the packet
received by N is a N's local END SID.
o an endpoint x node (i.e., an endpoint with cross-connect node):
the destination address (DA) of the packet received by N is a N's
local End.X SID with an array of layer 3 adjacencies.
This section describes the behavior of each of these nodes as a
repair node for the two time periods after the endpoint node fails.
4.1. Transit Node as Repair Node
When the Repair Node is a transit node, it provides fast protection
against the endpoint node failure as follows after looking up the
FIB.
IF the primary outbound interface used to forward the packet failed
IF NH = SRH && SL != 0 and
the failed endpoint is directly connected to Repair Node THEN
SL decreases*; update the IPv6 DA with SRH[SL];
FIB lookup on the updated DA;
forward the packet according to the matched entry;
ELSE
forward the packet according to the backup nexthop;
ELSE IF there is no FIB entry for forwarding the packet THEN
IF NH = SRH && SL != 0 THEN
SL decreases*; update the IPv6 DA with SRH[SL];
FIB lookup on the updated DA;
forward the packet according to the matched entry;
ELSE
drop the packet;
ELSE
forward accordingly to the matched entry;
*: SL could be decreased by any dedicated value from [1-N],
where N is the current value of SL.
Chen, et al. Expires January 13, 2022 [Page 5]
Internet-Draft SRv6 Midpoint Protection July 2021
4.2. Endpoint Node as Repair Node
When the Repair Node is an endpoint node, it provides fast
protections for the failure through executing the following procedure
after looking up the FIB for the updated DA.
IF the primary outbound interface used to forward the packet failed
IF NH = SRH && SL != 0 and
the failed endpoint is directly connected to Repair Node THEN
SL decreases; update the IPv6 DA with SRH[SL];
FIB lookup on the updated DA;
forward the packet according to the matched entry;
ELSE
forward the packet according to the backup nexthop;
ELSE IF there is no FIB entry for forwarding the packet THEN
IF NH = SRH && SL != 0 THEN
SL decreases; update the IPv6 DA with SRH[SL];
FIB lookup on the updated DA;
forward the packet according to the matched entry;
ELSE
drop the packet;
ELSE
forward accordingly to the matched entry;
4.3. Endpoint x Node as Repair Node
When the Repair Node is an endpoint x node, it provides fast
protections for the failure through executing the following procedure
after updating DA.
Chen, et al. Expires January 13, 2022 [Page 6]
Internet-Draft SRv6 Midpoint Protection July 2021
IF the layer-3 adjacency interface is down THEN
FIB lookup on the updated DA;
IF the primary interface used to forward the packet failed THEN
IF NH = SRH && SL != 0 and
the failed endpoint directly connected to Repair Node THEN
SL decreases; update the IPv6 DA with SRH[SL];
FIB lookup on the updated DA;
forward the packet according to the matched entry;
ELSE
forward the packet according to the backup nexthop;
ELSE IF there is no FIB entry for forwarding the packet THEN
IF NH = SRH && SL != 0 THEN
SL decreases; update the IPv6 DA with SRH[SL];
FIB lookup on the updated DA;
forward the packet according to the matched entry;
ELSE
drop the packet;
ELSE
forward accordingly to the matched entry;
5. Determining whether the Endpoint could Be Bypassed
SRv6 Midpoint Protection provides a mechanism to bypass a failed
endpoint. But in some scenarios, some important functions may be
implemented in the bypassed failed endpoints that should not be
bypassed, such as firewall functionality or In-situ Flow Information
Telemetry of a specified path. Therefore, a mechanism is needed to
indicate whether an endpoint can be bypassed or not.
[I-D.li-rtgwg-enhanced-ti-lfa] provides method to determine whether
enbale SRv6 midpoint protection or not by defining a "no bypass" flag
for the SIDs in IGP.
6. Security Considerations
This section reviews security considerations related to SRv6 Midpoint
protection processing discussed in this document.To ensure that the
Repair node does not modify the SRH header Encapsulated by nodes
outside the SRv6 Domain.Only the segment within the SRH is same
domain as the repair node. So it is necessary to check the skipped
segment have same block as repair node.
7. IANA Considerations
This document makes no request of IANA.
Note to RFC Editor: this section may be removed on publication as an
RFC.
Chen, et al. Expires January 13, 2022 [Page 7]
Internet-Draft SRv6 Midpoint Protection July 2021
8. Acknowledgements
9. References
9.1. Normative References
[I-D.ietf-lsr-isis-srv6-extensions]
Psenak, P., Filsfils, C., Bashandy, A., Decraene, B., and
Z. Hu, "IS-IS Extension to Support Segment Routing over
IPv6 Dataplane", draft-ietf-lsr-isis-srv6-extensions-14
(work in progress), April 2021.
[I-D.ietf-lsr-ospfv3-srv6-extensions]
Li, Z., Hu, Z., Cheng, D., Talaulikar, K., and P. Psenak,
"OSPFv3 Extensions for SRv6", draft-ietf-lsr-
ospfv3-srv6-extensions-02 (work in progress), February
2021.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7356] Ginsberg, L., Previdi, S., and Y. Yang, "IS-IS Flooding
Scope Link State PDUs (LSPs)", RFC 7356,
DOI 10.17487/RFC7356, September 2014,
<https://www.rfc-editor.org/info/rfc7356>.
[RFC8986] Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer,
D., Matsushima, S., and Z. Li, "Segment Routing over IPv6
(SRv6) Network Programming", RFC 8986,
DOI 10.17487/RFC8986, February 2021,
<https://www.rfc-editor.org/info/rfc8986>.
9.2. Informative References
[I-D.hegde-spring-node-protection-for-sr-te-paths]
Hegde, S., Bowers, C., Litkowski, S., Xu, X., and F. Xu,
"Node Protection for SR-TE Paths", draft-hegde-spring-
node-protection-for-sr-te-paths-07 (work in progress),
July 2020.
[I-D.hu-spring-segment-routing-proxy-forwarding]
Hu, Z., Chen, H., Yao, J., Bowers, C., Yongqing, and
Yisong, "SR-TE Path Midpoint Restoration", draft-hu-
spring-segment-routing-proxy-forwarding-14 (work in
progress), April 2021.
Chen, et al. Expires January 13, 2022 [Page 8]
Internet-Draft SRv6 Midpoint Protection July 2021
[I-D.ietf-rtgwg-segment-routing-ti-lfa]
Litkowski, S., Bashandy, A., Filsfils, C., Francois, P.,
Decraene, B., and D. Voyer, "Topology Independent Fast
Reroute using Segment Routing", draft-ietf-rtgwg-segment-
routing-ti-lfa-06 (work in progress), February 2021.
[I-D.ietf-spring-segment-routing-policy]
Filsfils, C., Talaulikar, K., Voyer, D., Bogdanov, A., and
P. Mattes, "Segment Routing Policy Architecture", draft-
ietf-spring-segment-routing-policy-11 (work in progress),
April 2021.
[I-D.li-rtgwg-enhanced-ti-lfa]
Li, C., Hu, Z., Zhu, Y., and S. Hegde, "Enhanced Topology
Independent Loop-free Alternate Fast Re-route", draft-li-
rtgwg-enhanced-ti-lfa-03 (work in progress), October 2020.
[I-D.sivabalan-pce-binding-label-sid]
Sivabalan, S., Filsfils, C., Tantsura, J., Hardwick, J.,
Previdi, S., and C. Li, "Carrying Binding Label/Segment-ID
in PCE-based Networks.", draft-sivabalan-pce-binding-
label-sid-07 (work in progress), July 2019.
[RFC5462] Andersson, L. and R. Asati, "Multiprotocol Label Switching
(MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic
Class" Field", RFC 5462, DOI 10.17487/RFC5462, February
2009, <https://www.rfc-editor.org/info/rfc5462>.
Authors' Addresses
Huanan Chen
China Telecom
109, West Zhongshan Road, Tianhe District
Guangzhou 510000
China
Email: chenhuan6@chinatelecom.cn
Zhibo Hu
Huawei Technologies
Huawei Bld., No.156 Beiqing Rd.
Beijing 100095
China
Email: huzhibo@huawei.com
Chen, et al. Expires January 13, 2022 [Page 9]
Internet-Draft SRv6 Midpoint Protection July 2021
Huaimo Chen
Futurewei
Boston, MA
USA
Email: Huaimo.chen@futurewei.com
Xuesong Geng
Huawei Technologies
Email: gengxuesong@huawei.com
Yisong Liu
China Mobile
Email: liuyisong@chinamobile.com
Chen, et al. Expires January 13, 2022 [Page 10]