rtgwg Working Group W. Cheng
Internet-Draft W. Jiang
Intended status: Standards Track China Mobile
Expires: October 26, 2022 C. Lin
Y. Qiu
New H3C Technologies
April 27, 2022
SRv6 Egress Protection in Multi-home scenario
draft-cheng-rtgwg-srv6-multihome-egress-protection-00
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on October 26, 2021.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Cheng, et al. Expire October, 2022 [Page 1]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Abstract
This document describes a SRv6 egress node protection mechanism in
multi-home scenarios.
Table of Contents
1. Introduction ................................................. 2
2. Terminology .................................................. 3
3. Multi-home SRv6 Egress Protection Mechanism .................. 3
3.1. B-flag in Segment Routing Header ........................ 3
3.2. Procedure of Multi-home Egress Protection on SRv6 TE Path 3
3.2.1. Procedure on the Ingress Endpoint .................. 4
3.2.2. Procedure on the Penultimate Endpoint .............. 6
3.3. Procedure of Multi-home Egress Protection on SRv6 BE Path 7
4. Multi-home SRv6 Egress Protection Example .................... 8
5. IANA Considerations ......................................... 10
6. Security Considerations ..................................... 10
7. References .................................................. 11
7.1. Normative References ................................... 11
7.2. Informative References ................................. 12
8. Acknowledgments ............................................. 12
Authors' Addresses ............................................. 12
1. Introduction
The fast protection of a transit node of a Segment Routing (SR) path
or tunnel is described in [I-D.ietf-rtgwg-segment-routing-ti-lfa]
and [I-D.hu-spring-segment-routing-proxy-forwarding]. [RFC8400]
specifies the fast protection of egress node(s) of an MPLS TE LSP
tunnel including P2P TE LSP tunnel and P2MP TE LSP tunnel in details.
However, these documents do not discuss the fast protection of the
egress node of a Segment Routing for IPv6 (SRv6) path or tunnel.
[I-D.ietf-rtgwg-srv6-egress-protection] proposes mirror protection
mechanism and presents protocol extensions for the fast protection
of the egress node of a SRv6 path or tunnel. However, the mechanism
provided in this document is relatively complex. It is necessary to
configure the Mirror SID for the protected egress node on the backup
egress node. The mirror relationship is distributed through IGP and
BGP protocols to automatically create mapping entries.
Cheng, et al. Expires October, 2022 [Page 2]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
This document introduces a simplified protection mechanism of the
egress node of a SRv6 path. Only expanding the data plane can
perform fast path switching in case of egress node failure.
2. Terminology
The following terminologies are used in this document.
SR: Segment Routing
SRv6: SR for IPv6
SRH: Segment Routing Header
SID: Segment Identifier
CE: Customer Edge
PE: Provider Edge
VPN: Virtual Private Network
3. Multi-home SRv6 Egress Protection Mechanism
This section describes the mechanism of SRv6 path egress protection
in multi-home scenarios and the extension of SRH extension header.
3.1. B-flag in Segment Routing Header
[RFC8754] describes the Segment Routing Header (SRH) and how SR
capable nodes use it. The SRH contains an 8-bit "Flags" field.
This document defines the following bit in the SRH Flags field to
carry the B-flag:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
| |B| |
+-+-+-+-+-+-+-+-+
Where:
- B-flag: The marking bit of carrying backup SID in segment list. If
the B-flag is set to 1, a backup SID is carried in the segment list.
3.2. Procedure of Multi-home Egress Protection on SRv6 TE Path
The Figure 1 is used to explain the multi-home egress node
protection mechanism.
Cheng, et al. Expires October, 2022 [Page 3]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
Locator: A3:1::/64
VPN SID: A3:1::B100
+---+ *** +---+ *** +---+ *** +---+ +---+
|PE1|-----| P1|-----| P2|-----|PE3|---|CE2|
+---+ +---+ +---+ +---+ +---+
/ | | | | \ /
+---+/ | | | | \ /
|CE1| | | | | X
+---+\ | | | | / \
\ | | | | / \
+---+ +---+ +---+ +---+ +---+
|PE2|-----| P3|-----| P4|-----|PE4|---|CE3|
+---+ +---+ +---+ +---+ +---+
Locator: A4:1::/64
VPN SID: A4:1::B100
PE3 Egress
PE4 Backup Egress
CEx Customer Edge
Px Non-Provider Edge
*** SR Path
Figure 1
3.2.1. Procedure on the Ingress Endpoint
In the multi-home or dual-home scenario, after the ingress node
learns the multi-home or dual-home route through routing protocol,
it determines the optimal path and suboptimal path according to the
route optimization strategy. The egress node on the optimal path is
an primary egress, and the SID of the primary egress node is used as
the primary SID The egress node on the suboptimal path is an backup
egress,and the SID of the backup egress node is used as the backup
SID.
On the path forwarded based on SRv6 TE policy, when the ingress node
encapsulates the SRH extension header, judge whether the primary VPN
SID of the egress node (PE1) has a backup SID. If yes, insert the
backup SID into the position of SRH[Last Entry], and set B-flag to 1
to identify that the backup SID has been carried in the last
Cheng, et al. Expires October, 2022 [Page 4]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
position of the segment list, then the value of SL is set to n-1. The
format of SRH extension header filling is shown in the following
figure 2.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | SL = n-1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Last Entry=n |Flags(B-flag=1)| Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Active SID (Segment List[0], 128 bits IPv6 address) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Segment List[n-1] (128 bits IPv6 address) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Backup SID (Segment List[n],128 bits IPv6 value) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// Optional Type Length Value objects (variable) //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2
Cheng, et al. Expires October, 2022 [Page 5]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
3.2.2. Procedure on the Penultimate Endpoint
Normally, the traffic is forwarded along the path P1->P2->PE3->CE2.
When primary egress node (PE3) fails, P2 finds out that the PE3's
SID is unreachable and the B-flag value is set. Then P2 modifies the
destination address of the packet to SRH[Last Entry] which is the
backup SID, and sends the modified packet to backup egress node
(PE4). Through this method P2 can provide fast protection for the
egress failure.
The detailed processing can be described in two cases according to
the endpoint behavior of the destination address of the packet
received by P2.
The behavior of the local endpoint is END.X
When receiving a packet destined to a local End.X SID whose
outgoing interface is down, the penultimate endpoint acting as a
Repair Node can provide fast protection for the failure of
directly connected egress nodes after SL decreasing through
executing the following procedures.
IF B-flag = 1 THEN
IF SL = 0 and the failed egress node is directly connected to
Repair Node THEN
Update the IPv6 DA with SRH[Last Entry];
FIB lookup on the updated DA;
Forward the packet according to the matched entry;
ELSE IF SL = 1 and SRH[1] and SRH[0] are the SIDs of the
failed egress node directly connected to Repair Node THEN
Update the IPv6 DA with SRH[Last Entry];
FIB lookup on the updated DA;
Forward the packet according to the matched entry;
The behavior of the local endpoint is END
After looking up the FIB for the updated DA with Segment
List[Segments Left] and SL decreasing, in the following two cases,
the penultimate endpoint acting as a Repair Node can provide fast
protections for the failure of directly connected egress nodes
through executing the following procedure.
Cheng, et al. Expires October, 2022 [Page 6]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
Case 1: For the packet whose Next Header is SRH and Segments Left
is equal to 1, perform the following processing:
IF B-flag = 1 and SRH[1] and SRH[0] are the SIDs of the failed
egress node directly connected to Repair Node THEN
Update the IPv6 DA with SRH[Last Entry];
FIB lookup on the updated DA;
Forward the packet according to the matched entry;
Case 2: For the packet whose Next Header is SRH and Segments Left
is equal to 0, perform the following processing:
IF B-flag = 1 and the failed egress endpoint is directly
connected to Repair Node THEN
Update the IPv6 DA with SRH[Last Entry];
FIB lookup on the updated DA;
Forward the packet according to the matched entry;
When the packet arrives at PE4, PE4 removes the outer IPv6 header,
and forwards the exposed inner packet.
After the route convergence is completed, the ingress node (PE1)
will reselect the forwarding path for the traffic to VPN, and switch
the path P1->P3->P4->PE4->CE2 to the CE to the egress node (PE4).
After that, P2 no longer needs to forward the packet with the
destination address of PE3.
Considering that the egress node may check the consistency between
the segment list and the destination address, for the packet with B-
flag 1, as long as the destination address is the same as any one of
SRH[0] or SRH[Last Entry], it is considered to be consistent.
In addition, when a penultimate endpoint using non-PSP-flavored SID
receives a packet with B-flag of 1, it is recommended to directly
remove the SRH extension header after replacing the destination
address with SRH[Last Entry].
3.3. Procedure of Multi-home Egress Protection on SRv6 BE Path
The multi-home egress node protection processing on the SRv6 BE path
is consistent with that on the SRv6 TE path, except that the ingress
Cheng, et al. Expires October, 2022 [Page 7]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
node is required to add an SRH extension header with the active SID,
backup SID and B-flag when encapsulating the outer IPv6 packet
header.
In the multi-home scenario egress node scenario, the ingress node
determines the active SID (PE3's SID) and the backup SID (PE4's SID)
of the egress node through the optimization strategy of the routing
protocol.
When the traffic from PE1 to CE2 is forwarded through the SRv6 BE
path, in order to realize the fast protection of egress node failure,
when the ingress node adds an outer IPv6 packet header to the
forwarded packet, it must encapsulate the SRH extension header at
the same time. The contents filled in the SRH extension header are
the same as Figure 2 in Section 3.2.1, in which the segment list
only fills in the active SID and backup SID, the SL is set to 0, the
last entry is set to 1, and the B-flag is set to 1. The active SID
is used as the destination address of the outer IP packet header.
Normally, because the destination address of the packet is the
active SID (PE3's SID), P1 and P2 will forward the packet to PE3
according to the destination address.
Once PE3 fails, the processing of the penultimate endpoint is the
same as that on the SRv6 TE path. When P2 finds out that the route
to the directly connected egress node PE3 is unreachable, if the B-
flag is 1, modify the destination address to the backup SID in
SRH[1], and send the packet to the updated destination address.
4. Multi-home SRv6 Egress Protection Example
Figure 3 shows an example of protecting egress PE3 of a SRv6 TE path,
which is from ingress PE1 to egress PE3.
Cheng, et al. Expires October, 2022 [Page 8]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
Locator: A3:1::/64
Locator:A0:1::/64 VPN SID: A3:1::B100
+---+ *** +---+ *** +---+ *** +---+ +---+
|PE1|-----| P1|-----| P2|-----|PE3|---|CE2|
+---+ +---+ +---+ +---+ +---+
/ | | |& | \ /
+---+/ | | |& | \ /
|CE1| | | |& | X
+---+\ | | |& | / \
\ | | |& | / \
+---+ +---+ +---+ &&& +---+ +---+
|PE2|-----| P3|-----| P4|-----|PE4|---|CE3|
+---+ +---+ +---+ +---+ +---+
Locator: A4:1::/64
VPN SID: A4:1::B100
PE3 Egress
PE4 Backup Egress
CEx Customer Edge
Px Non-Provider Edge
*** SR Path
&&& backup Path
Figure 3
In this document, a SID list is represented as <S1, S2, S3> where S1
is the first SID to visit, S2 is the second SID to visit and S3 is
the last SID to visit along the SRv6 path.
In Figure 3, Both CE2 and CE3 are dual home to PE3 and PE4. PE1 has
a locator A0:1::/64. P1 has a locator A1:1::/64. P2 has a locator
A2:1::/64 and END.X SID A2:1::A100. PE3 has a locator A3:1::/64 and
a VPN SID A3:1::B100. PE4 has a locator A4:1::/64 and VPN SID
A4:1::B100. The traffic from CE1 to CE2 is forwarded along the path
PE1->P1->P2->PE3. After the configuration, PE1 determines that PE3's
backup SID is PE4's VPN SID through the routing optimization
strategy of BGP.
In normal operations, after receiving a packet with destination PE3,
P2 forwards the packet to PE3 according to its FIB. When PE3
receives the packet, it sends the packet to CE2.
When PE1 receives the packet from CE1 to CE2, PE1 encapsulates the
packet with IPv6 header. The segment list in SRH is designed as
<A0:1::1, A1:1::1, A2:1::A100, A3:1::B100, A4:1::B100>. The SL is
set to 3, the Last Entry is set to 4, and B-flag is set to 1.
When P2 receives a packet destined to END.X SID A2:1::A100, in
normal operations, it forwards the packet with source A0:1::1 and
Cheng, et al. Expires October, 2022 [Page 9]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
destination PE3's VPN SID A3:1::B100 from the link between P2 and
PE3 according to END.X SID.
When PE3 fails, P2 receives the packet to be sent to PE3's VPN SID
A3:1::B100. P2 finds that the outgoing interface is down. If the B-
flag is 1, P2 changes the destination address of the packet with the
backup SID of SRH[4], removes SRH extension header and sends the
modified packet to A4:1::B100.
When PE4 receives the modified packet, it decapsulates the packet
and forwards the decapsulated packet by executing End.DT6 behavior
for an End.DT6 SID instance.
5. IANA Considerations
This document requests that IANA allocate the following registration
in the "Segment Routing Header Flags" sub-registry for the "Internet
Protocol Version 6 (IPv6) Parameters" registry maintained by IANA:
+-------+------------------------------+---------------+
| Bit | Description | Reference |
+=======+==============================+===============+
| 4 | B-flag | This document |
+-------+------------------------------+---------------+
6. Security Considerations
[RFC8754] defines the notion of an SR domain and use of SRH within
the SR domain. The use of egress protection mechanism described in
this document is restricted to an SR domain. For example, similar
to the SID manipulation, B-flag manipulation is not considered as a
threat within the SR domain. Procedures for securing an SR domain
are defined the section 5.1 and section 7 of [RFC8754].
This document does not impose any additional security challenges to
be considered beyond security threats described in [RFC8754],
[RFC8679] and [RFC8986].
Cheng, et al. Expires October, 2022 [Page 10]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
7. References
7.1. Normative References
[I-D.ietf-rtgwg-segment-routing-ti-lfa] Litkowski, S., Bashandy, A.,
Filsfils, C., Francois, P., Decraene, B., and D. Voyer,
"Topology Independent Fast Reroute using Segment Routing",
Work in Progress, Internet-Draft, draft-ietf-rtgwg-
segment-routing-ti-lfa-08, 21 January 2022,
<https://www.ietf.org/archive/id/draft-ietf-rtgwg-segment-
routing-ti-lfa-07.txt>.
[I-D.hu-spring-segment-routing-proxy-forwarding] Hu, Z., Chen, H.,
Yao, J., Bowers, C., Yongqing, and Yisong, "SR-TE Path
Midpoint Restoration", Work in Progress, Internet-Draft,
draft-hu-spring-segment-routing-proxy-forwarding-18, 1
September 2022, <https://www.ietf.org/archive/id/draft-hu-
spring-segment-routing-proxy-forwarding-18.txt>.
[I-D.ietf-rtgwg-srv6-egress-protection] Hu, Z., Chen, H., Chen, H.,
Wu, P., Toy, M., Cao, C., He T., Liu, L., Liu, X., "SRv6
Path Egress Protection", Work in Progress, Internet-Draft,
draft-ietf-rtgwg-srv6-egress-protection-04, 17 October
2021, < https://www.ietf.org/archive/id/draft-ietf-rtgwg-
srv6-egress-protection-04.txt >
[RFC8400] Chen, H., Liu, A., Saad, T., Xu, F., and L. Huang,
"Extensions to RSVP-TE for Label Switched Path (LSP)
Egress Protection", RFC 8400, DOI 10.17487/RFC8400, June
2018, <https://www.rfc-editor.org/info/rfc8400>.
[RFC8679] Shen, Y., Jeganathan, M., Decraene, B., Gredler, H.,
Michel, C., and H. Chen, "MPLS Egress Protection
Framework", RFC 8679, DOI 10.17487/RFC8679, December 2019,
<https://www.rfc-editor.org/info/rfc8679>.
[RFC8754] Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J.,
Matsushima, S., and D. Voyer, "IPv6 Segment Routing
Header(SRH)", RFC 8754, DOI 10.17487/RFC8754, March 2020,
<https://www.rfc-editor.org/info/rfc8754>.
[RFC8986] Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer,
D., Matsushima, S., and Z. Li, "Segment Routing over IPv6
(SRv6) Network Programming", RFC 8986, DOI
10.17487/RFC8986, February 2021, <https://www.rfc-
editor.org/info/rfc8986>.
Cheng, et al. Expires October, 2022 [Page 11]
Internet-Draft Multi-home SRv6 Egress Protection April 2022
7.2. Informative References
TBD
8. Acknowledgments
The authors would like to thank the following for their valuable
contributions of this document:
Yisong Liu
China Mobile
Authors' Addresses
Weiqiang Cheng
China Mobile
Email: chengweiqiang@chinamobile.com
Wenying Jiang
China Mobile
Email: jiangwenying@chinamobile.com
Changwang Lin
New H3C Technologies
Email: linchangwang.04414@h3c.com
Yuanxiang Qiu
New H3C Technologies
Email: qiuyuanxiang@h3c.com
Cheng, et al. Expires October, 2022 [Page 12]