Internet Engineering Task Force R. Cole
Internet-Draft Johns Hopkins University
Intended status: Standards Track J. Macker
Expires: September 1, 2009 B. Adamson
Naval Research Laboratory
S. Harnedy
Booz Allen Hamilton
February 28, 2009
Definition of Managed Objects for the Manet Simplified Multicast
Framework Relay Set Process
draft-cole-manet-smf-mib-02
Status of This Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on September 1, 2009.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document.
Cole, et al. Expires September 1, 2009 [Page 1]
Internet-Draft The SMF MIB February 2009
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes objects for configuring aspects of the
Simplified Multicast Forwarding (SMF) process. The SMF MIB also
reports state information, performance metrics, and notifications.
In addition to configuration, this additional state and performance
information is useful to management stations troubleshooting
multicast forwarding problems.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . . 3
3. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1. SMF Management Model . . . . . . . . . . . . . . . . . . . 4
4.2. Terms . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. Structure of the MIB Module . . . . . . . . . . . . . . . . . 6
5.1. Textual Conventions . . . . . . . . . . . . . . . . . . . 6
5.2. The Capabilities Group . . . . . . . . . . . . . . . . . . 6
5.3. The Configuration Group . . . . . . . . . . . . . . . . . 7
5.4. The State Group . . . . . . . . . . . . . . . . . . . . . 7
5.5. The Performance Group . . . . . . . . . . . . . . . . . . 7
5.6. The Reports Group . . . . . . . . . . . . . . . . . . . . 8
5.7. The Notifications Group . . . . . . . . . . . . . . . . . 8
6. Relationship to Other MIB Modules . . . . . . . . . . . . . . 8
6.1. Relationship to the SNMPv2-MIB . . . . . . . . . . . . . . 9
6.2. Relationship to the IF-MIB . . . . . . . . . . . . . . . . 9
6.3. MIB modules required for IMPORTS . . . . . . . . . . . . . 9
7. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 9
8. Security Considerations . . . . . . . . . . . . . . . . . . . 51
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 53
10. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 54
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 54
12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 54
12.1. Normative References . . . . . . . . . . . . . . . . . . . 54
12.2. Informative References . . . . . . . . . . . . . . . . . . 55
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 55
Appendix B. Open Issues . . . . . . . . . . . . . . . . . . . . . 55
Appendix C. . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cole, et al. Expires September 1, 2009 [Page 2]
Internet-Draft The SMF MIB February 2009
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes objects for configuring aspects of a
process implementing Simplified Multicast Forwarding (SMF)
[I-D.ietf-manet-smf]. SMF provides multicast duplicate packet
detection (DPD) and supports algorithms for constructing an estimate
of a mobile ad hoc network (MANET) Minimum Connected Dominating Set
(MCDS) for efficient multicast forwarding. The SMF MIB also reports
state information, performance metrics, and notifications. In
addition to configuration, this additional state and performance
information is useful to management stations troubleshooting
multicast forwarding problems.
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
3. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
4. Overview
SMF provides methods for implementing DPD-based multicast forwarding
with the optional use of CDS-based relay sets. The MCDS is the
smallest set of MANET nodes (comprising a connected cluster) which
cover all the nodes in the cluster with their transmissions. As the
density of the MANET nodes increase, the fraction of nodes required
in an MCDS decreases. Using the MCDS as a multicast forwarding set
then becomes an efficient multicast mechanism for MANETs.
Various algorithms for the construction of estimates of the MCDS
exist. The Simplified Multicast Framework [I-D.ietf-manet-smf]
Cole, et al. Expires September 1, 2009 [Page 3]
Internet-Draft The SMF MIB February 2009
describes some of these. It further defines various operational
modes for a node which is participating in the collective creation of
the MCDS estimates. These modes depend upon the set of related MANET
routing and discovery protocols and mechanisms in operation in the
specific MANET node.
A SMF routers' MIB contains SMF process configuration parameters
(e.g. specific CDS algorithm), state information (e.g., current
membership in the CDS), performance counters (e.g., packet counters),
and notifications.
4.1. SMF Management Model
This section describes the management model for the SMF node process.
Figure 1 (reproduced from Figure 4 of [I-D.ietf-manet-smf]) shows the
relationship between the SMF Relay Set selection algorithm and the
related algorithms, processes and protocols running in the MANET
nodes. The Relay Set Selection Algorithm (RSSA) can rely upon
topology information gotten from the MANET Neighborhood Discovery
Protocol (NHDP), from the specific MANET routing protocol running on
the node, or from Layer 2 information passed up to the higher layer
protocol processes.
Cole, et al. Expires September 1, 2009 [Page 4]
Internet-Draft The SMF MIB February 2009
Possible L2 Trigger/Information
|
|
______________ ______|_____ __________________
| MANET | | | | |
| Neighborhood | | Relay Set | | Other Heuristics |
| Discovery |------------| Selection |-------| (Preference,etc) |
| Protocol | neighbor | Algorithm | | |
|______________| info |____________| |__________________|
\ /
\ /
neighbor\ / Dynamic Relay
info* \ ____________ / Set Status
\ | SMF | / (State, {neighbor info})
`---| Relay Set |---'
| State |
---|____________|
/
/
______________
| Coexistent |
| MANET |
| Unicast |
| Process |
|______________|
Figure 1: SMF Relay Set Control Options
4.2. Terms
The following definitions apply throughout this document:
o Configuration Objects - switches, tables, objects which are
initialized to default settings or set through the management
interface defined by this MIB.
o Tunable Configuration Objects - objects whose values affect timing
or attempt bounds on the SMF RS process.
o State Objects - automatically generated values which define the
current operating state of the SMF RS process in the router.
o Performance Objects - automatically generated values which help an
administrator or automated tool to assess the performance of the
CDS multicast process on the router and the overall multicasting
performance within the MANET routing domain.
Cole, et al. Expires September 1, 2009 [Page 5]
Internet-Draft The SMF MIB February 2009
5. Structure of the MIB Module
This section presents the structure of the SMF MIB module. The
objects are arranged into the following groups:
o smfMIBNotifications - defines the notifications associated with
the SMF MIB.
o smfMIBObjects - defines the objects forming the basis for the SMF
MIB. These objects are divided up by function into the following
groups:
o
* Capabilities Group - This group contains the SMF objects that
the device uses to advertise its local capabilities with
respect to, e.g., the supported RSSAs.
* Configuration Group - This group contains the SMF objects that
configure specific options that determine the overall operation
of the SMF RSSA and the resulting multicast performance.
* State Group - Contains information describing the current state
of the SMF RSSA process such as the Neighbor Table.
* Performance Group - Contains objects which help to characterize
the performance of the SMF RSSA process, typically statistics
counters.
* Reports Group - Contains objects which allow the device to
develop and locally store performance related reports. The
management application can then pull these locally stored
reports when it wishes.
o smfMIBConformance - defines minimal and full conformance of
implementations to this SMF MIB.
5.1. Textual Conventions
The textual conventions used in the SMF MIB are as follows. The
RowStatus textual convention is imported from RFC 2579 [RFC2579].
5.2. The Capabilities Group
The SMF device supports a set of capabilities. The list of
capabilities which the device can advertise are:
Cole, et al. Expires September 1, 2009 [Page 6]
Internet-Draft The SMF MIB February 2009
o Operational Mode - topology information from NHDP, CDS-aware
unicast routing or Cross-layer from Layer 2
o SMF RSSA - the specific RSSA operational on the device
5.3. The Configuration Group
The SMF device is configured with a set of controls. The list of
configuration controls for the SMF device follow.
o Operational Mode - topology information from NHDP, CDS-aware
unicast routing or Cross-layer from Layer 2
o SMF RSSA - the specific RSSA operational on the device
o Duplicate Packet detection for IPv4 - Identification-based or
Hash-based DPD
o Duplicate Packet detection for IPv6 - Identification-based or
Hash-based DPD
o NHDP RSSA Message TLV - if NHDP mode is selected, then is the RSSA
Message TLV included in the NHDP exchanges. (Question: Is this
and the following two TLVs optional and are they included as a
group or independently of one another?)
o NHDP RSSA Address Block TLV - if NHDP mode is selected, then is
the RSSA Address Block TLV included in the NHDP exchanges.
o Router Priority TLV - if NHDP mode is selected, then is the Router
Priority TLV included in the NHDP exchanges.
5.4. The State Group
The State Subtree reports current state information.
o Node RSS State - is the node currently in or out of the Relay Set.
o Neighbors Table - a table containing current neighbors and their
operational RSSA.
5.5. The Performance Group
The Performance subtree reports primarily counters that relate to SMF
RSSA performance. The SMF performance counters consists of per node
and per interface objects: (Note: Need to have a discussion of the
important and measurable events related to SMF RSSA multicast
performance.) (Note: Do we need to break these out by type, i.e., v4
Cole, et al. Expires September 1, 2009 [Page 7]
Internet-Draft The SMF MIB February 2009
versus v6?)
o Total multicast packets received -
o Total multicast packets forwarded -
o Total duplicate multicast packets detected -
o Per interface statistics table with the following entries:
o
* Multicast packets received
* Multicast packets forwarded
* Duplicate multicast packets detected
5.6. The Reports Group
The SMF device supports a a capability to generate and store locally
a set of performance reports. The objects to control the generation
of these reports and to identify the information contained within
these reports are contained within this group. These objects
include:
o Report Control Objects - which specify the storage requirements,
the time and duration and the authorship of the reports.
o Report Objects - which identify the information, i.e., metrics,
contained within these reports. Currently, these objects
represent a sub-set of the objects found within the Performance
Group discussed above.
5.7. The Notifications Group
The Notifications Subtree contains the list of notifications
supported within the SMF-MIB and their intended purpose or utility.
This group is currently empty.
6. Relationship to Other MIB Modules
[TODO]: The text of this section specifies the relationship of the
MIB modules contained in this document to other standards,
particularly to standards containing other MIB modules. Definitions
imported from other MIB modules and other MIB modules that SHOULD be
implemented in conjunction with the MIB module contained within this
document are identified in this section.
Cole, et al. Expires September 1, 2009 [Page 8]
Internet-Draft The SMF MIB February 2009
6.1. Relationship to the SNMPv2-MIB
The 'system' group in the SNMPv2-MIB [RFC3418] is defined as being
mandatory for all systems, and the objects apply to the entity as a
whole. The 'system' group provides identification of the management
entity and certain other system-wide data. The SMF-MIB does not
duplicate those objects.
6.2. Relationship to the IF-MIB
[TODO] This section is included as an example; If the MIB module is
not an adjunct of the Interface MIB, then this section should be
removed.
6.3. MIB modules required for IMPORTS
[TODO]: Citations are not permitted within a MIB module, but any
module mentioned in an IMPORTS clause or document mentioned in a
REFERENCE clause is a Normative reference, and must be cited
someplace within the narrative sections. If there are imported items
in the MIB module, such as Textual Conventions, that are not already
cited, they can be cited in text here. Since relationships to other
MIB modules should be described in the narrative text, this section
is typically used to cite modules from which Textual Conventions are
imported.
The following SMF-MIB module IMPORTS objects from SNMPv2-SMI
[RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], and IF-MIB
[RFC2863]
7. Definitions
MANET-SMF-MIB DEFINITIONS ::= BEGIN
IMPORTS
ZeroBasedCounter32
FROM RMON2-MIB -- [RFC2021]
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Counter32, Unsigned32, Integer32, mib-2
FROM SNMPv2-SMI -- [RFC2578]
TEXTUAL-CONVENTION, RowStatus, TruthValue,
TimeStamp, StorageType
FROM SNMPv2-TC -- [RFC2579]
Cole, et al. Expires September 1, 2009 [Page 9]
Internet-Draft The SMF MIB February 2009
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]
OwnerString
FROM RMON-MIB -- [RFC2819]
InterfaceIndexOrZero
FROM IF-MIB -- [RFC2863]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
InetAddress, InetAddressType,
InetAddressPrefixLength
FROM INET-ADDRESS-MIB -- [RFC4001]
;
manetSmfMIB MODULE-IDENTITY
LAST-UPDATED "200902271300Z" -- February 27, 2009
ORGANIZATION "IETF MANET Working Group"
CONTACT-INFO
"WG E-Mail: manet@ietf.org
WG Chairs: ian.chakeres@gmail.com
jmacker@nrl.navy.mil
Editors: Robert G. Cole
Johns Hopkins University
Applied Physics Lab and
Department of Computer Science
11000 Johns Hopkins Road
Room 02-257
Laurel, MD 22014
USA
+1 443 778-6951
robert.cole@jhuapl.edu
Joseph Macker
Naval Research Laboratory
Washington, D.C. 20375
USA
macker@itd.nrl.navy.mil
Brian Adamson
Naval Research Laboratory
Washington, D.C. 20375
Cole, et al. Expires September 1, 2009 [Page 10]
Internet-Draft The SMF MIB February 2009
USA
adamson@itd.nrl.navy.mil
Sean Harnedy
Booz Allen Hamilton
333 City Boulevard West
Orange, CA 92868
USA
+1 714 938-3898
harnedy_sean@bah.com"
DESCRIPTION
"This MIB module contains managed object definitions for
the Manet SMF RSSA process defined in: Macker, J.(ed.),
Simplified Multicast Forwarding draft-ietf-manet-smf-08,
November 03, 2008.
Copyright (C) The IETF Trust (2008). This version
of this MIB module is part of RFC xxxx; see the RFC
itself for full legal notices."
-- Revision History
REVISION "200902271300Z" -- February 27, 2009
DESCRIPTION
"Updated draft of this MIB module published as
draft-cole-manet-smf-mib-02.txt. Fairly extensive
revisions and additions to this MIB were made
in this version. Specifically, the following
changes were made in development of this version:
- added a Capabilities Group within the Objects
Group to allow the device to report supported
capabilities, e.g., RSSAs supported.
- added administrative status objects for device
and interfaces
- added multicast address forwarding tables, both
for configured (within Configuration Group) and
discovered (within the State Group).
- added additional Performance counters related
to DPD functions.
- Split up the performance counters into IPv4
and IPv6, for both global and per interface
statistics.
- Split out the reports capability into a seperate
Reports Group under the Objects Group.
"
REVISION "200811031300Z" -- November 03, 2008
DESCRIPTION
"Updated draft of this MIB module published as
Cole, et al. Expires September 1, 2009 [Page 11]
Internet-Draft The SMF MIB February 2009
draft-cole-manet-smf-mib-01.txt. Added gateway filter
table and reports capabilities following rmon."
REVISION "200807071200Z" -- July 07, 2008
DESCRIPTION
"Initial draft of this MIB module published as
draft-cole-manet-smf-mib-00.txt."
-- RFC-Editor assigns XXXX
::= { mib-2 998 } -- to be assigned by IANA
--
-- TEXTUAL CONVENTIONs
--
Status ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An indication of the operability of a DYMO
function or feature. For example, the status
of an interface: 'enabled' indicates that
it is willing to communicate with other DYMO routers,
and 'disabled' indicates that it is not."
SYNTAX INTEGER {
enabled (1),
disabled (2)
}
SmfOpModeID ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"An index that identifies through reference to a specific
SMF operations mode ...
"
SYNTAX Unsigned32 (1..2147483647)
SmfRssaID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An index that identifies through reference to a specific
RSSA algorithms ...
"
SYNTAX INTEGER {
cF(1),
sMPR(2),
eCDS(3),
mprCDS(4)
Cole, et al. Expires September 1, 2009 [Page 12]
Internet-Draft The SMF MIB February 2009
-- future(5-127)
-- noStdAction(128-239)
-- experimental(240-255)
}
--
-- Top-Level Object Identifier Assignments
--
smfMIBNotifications OBJECT IDENTIFIER ::= { manetSmfMIB 0 }
smfMIBObjects OBJECT IDENTIFIER ::= { manetSmfMIB 1 }
smfMIBConformance OBJECT IDENTIFIER ::= { manetSmfMIB 2 }
--
-- smfMIBObjects Assignments:
-- smfCapabilitiesGroup - 1
-- smfConfigurationGroup - 2
-- smfStateGroup - 3
-- smfPerformanceGroup - 4
-- smfReportsGroup - 5
--
--
-- smfCapabilitiesGroup
--
-- This group contains the SMF objects that identify specific
-- capabilities within this device related to SMF functions.
--
smfCapabilitiesGroup OBJECT IDENTIFIER ::= { smfMIBObjects 1 }
--
-- SMF Operational Mode Capabilities Table
--
smfOpModeCapabilitiesTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfOpModeCapabilitiesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The smfOpModeCapabilitiesTable contains ...
"
::= { smfCapabilitiesGroup 1 }
Cole, et al. Expires September 1, 2009 [Page 13]
Internet-Draft The SMF MIB February 2009
smfOpModeCapabilitiesEntry OBJECT-TYPE
SYNTAX SmfOpModeCapabilitiesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a particular operational
mode.
"
INDEX { smfOpModeCapabilitiesID }
::= { smfOpModeCapabilitiesTable 1 }
SmfOpModeCapabilitiesEntry ::= SEQUENCE {
smfOpModeCapabilitiesID SmfOpModeID,
smfOpModeCapabilitiesName SnmpAdminString,
smfOpModeCapabilitiesReference SnmpAdminString
}
smfOpModeCapabilitiesID OBJECT-TYPE
SYNTAX SmfOpModeID
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this entry. This object identifies
the particular operational mode for this device.
"
::= { smfOpModeCapabilitiesEntry 1 }
smfOpModeCapabilitiesName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual name of this operational
mode.
"
::= { smfOpModeCapabilitiesEntry 2 }
smfOpModeCapabilitiesReference OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a reference to the document that
defines this operational mode.
"
::= { smfOpModeCapabilitiesEntry 3 }
Cole, et al. Expires September 1, 2009 [Page 14]
Internet-Draft The SMF MIB February 2009
--
-- SMF RSSA Capabilities Table
--
smfRssaCapabilitiesTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfRssaCapabilitiesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The smfRssaCapabilitiesTable contains ...
"
::= { smfCapabilitiesGroup 2 }
smfRssaCapabilitiesEntry OBJECT-TYPE
SYNTAX SmfRssaCapabilitiesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a particular algorithm."
INDEX { smfRssaCapabilitiesID }
::= { smfRssaCapabilitiesTable 1 }
SmfRssaCapabilitiesEntry ::= SEQUENCE {
smfRssaCapabilitiesID SmfRssaID,
smfRssaCapabilitiesName SnmpAdminString,
smfRssaCapabilitiesReference SnmpAdminString
}
smfRssaCapabilitiesID OBJECT-TYPE
SYNTAX SmfRssaID
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this entry. This object identifies
the particular algorithm in this MIB module."
::= { smfRssaCapabilitiesEntry 1 }
smfRssaCapabilitiesName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual name of this algorithm.
"
::= { smfRssaCapabilitiesEntry 2 }
smfRssaCapabilitiesReference OBJECT-TYPE
SYNTAX SnmpAdminString
Cole, et al. Expires September 1, 2009 [Page 15]
Internet-Draft The SMF MIB February 2009
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a reference to the document that
defines this algorithm.
"
::= { smfRssaCapabilitiesEntry 3 }
--
-- smfConfigurationGroup
--
-- This group contains the SMF objects that configure specific
-- options that determine the overall performance and operation
-- of the multicast forwarding process for the router device
-- and its interfaces.
--
smfConfigurationGroup OBJECT IDENTIFIER ::= { smfMIBObjects 2 }
smfAdminStatus OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configured status of the SMF process
on this device. Enabled(1) means that
SMF is configured to run on this device.
Disabled(2) mean that the SMF process
is configured off."
::= { smfConfigurationGroup 1 }
smfConfiguredOpMode OBJECT-TYPE
SYNTAX INTEGER {
withNHDP(1),
cdsAwareRouting(2),
crossLayer(3),
other(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SMF RSS node operational mode.
Cole, et al. Expires September 1, 2009 [Page 16]
Internet-Draft The SMF MIB February 2009
The value withNHDP(1) indicates ...
The value cdsAwareRouting(2) indicates ...
The value crossLayer(3) indicates... ."
::= { smfConfigurationGroup 2 }
smfConfiguredRssa OBJECT-TYPE
SYNTAX SmfRssaID
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SMF RSS currently operational algorithm.
The value cf(1) indicates ...
The value experimental(240-255) indicates... ."
::= { smfConfigurationGroup 3 }
smfRssaMember OBJECT-TYPE
SYNTAX INTEGER {
potential(1),
always(2),
never(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The RSSA downselects a set of forwarders for
multicast forwarding. Sometimes it is useful
to force an agent to be included or excluded
from the resulting RSS. This object is a
switch to allow for this behavior.
The value potential(1) allows the selected
RSSA to determine if this agent is included
or excluded from the RSS.
The value always(1) forces the selected
RSSA include this agent in the RSS.
The value never(3) forces the selected
RSSA to exclude this agent from the RSS."
::= { smfConfigurationGroup 4 }
smfIpv4Dpd OBJECT-TYPE
SYNTAX INTEGER {
identificationBased(1),
hashBased(2)
Cole, et al. Expires September 1, 2009 [Page 17]
Internet-Draft The SMF MIB February 2009
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The current method for IPv4 duplicate packet
detection.
The value identificationBased(1)
indicates...
The value 'hashBased(2) indicates... ."
::= { smfConfigurationGroup 5 }
smfIpv6Dpd OBJECT-TYPE
SYNTAX INTEGER {
identificationBased(1),
hashBased(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The current method for IPv6 duplicate packet
detection.
The value identificationBased(1)
indicates...
The value 'hashBased(2) indicates... ."
::= { smfConfigurationGroup 6 }
smfMaxPktLifetime OBJECT-TYPE
SYNTAX Integer32 (0..65535)
UNITS "Seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The estimate of the network packet
traversal time.
"
DEFVAL { 60 }
::= { smfConfigurationGroup 7 }
smfDpdMaxMemorySize OBJECT-TYPE
SYNTAX Integer32 (0..65535)
UNITS "Kilo-Bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The locally reserved memory for storage
of cached DPD records for both IPv4 and
Cole, et al. Expires September 1, 2009 [Page 18]
Internet-Draft The SMF MIB February 2009
IPv6 methods.
"
DEFVAL { 1024 }
::= { smfConfigurationGroup 8 }
smfDpdEntryMaxLifetime OBJECT-TYPE
SYNTAX Integer32 (0..65525)
UNITS "Seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum lifetime of a cached DPD
record in the local device storage.
"
DEFVAL { 600 }
::= { smfConfigurationGroup 9 }
--
-- Configuration of messages to be included in
-- NHDP message exchanges in support of SMF
-- operations.
--
smfNhdpRssaMesgTLVIncluded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the associated NHDP messages
include the RSSA Message TLV, or not. This
is an optional SMF operational setting.
The value true(1) indicates that this TLV is
included; the value false(2) indicates that it
is not included."
::= { smfConfigurationGroup 10 }
smfNhdpRssaAddrBlockTLVIncluded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the associated NHDP messages
include the RSSA Address Block TLV, or not.
This is an optional SMF operational setting.
The value true(1) indicates that this TLV is
included; the value false(2) indicates that it
is not included."
Cole, et al. Expires September 1, 2009 [Page 19]
Internet-Draft The SMF MIB February 2009
::= { smfConfigurationGroup 11 }
smfNhdpRouterPriorityTLVIncluded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the associated NHDP messages
include the RSSA Router Priority TLV, or not.
This is an optional SMF operational setting.
The value true(1) indicates that this TLV is
included; the value false(2) indicates that it
is not included."
::= { smfConfigurationGroup 12 }
--
-- Table identifying configured multicast addresses to be forwarded.
--
smfConfiguredAddrForwardingTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfConfiguredAddrForwardingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing information on multicast
addresses which are to be forwarded by the SMF process.
Entries in this table are configured. As well, addresses
to be forwarded by the SMF device can be dynamically discovered
by other means. The corresponding state table,
smfDiscoveredAddrForwardingTable contains
these additional, dynamically discovered address for
forwarding.
Each row is associated with a range of multicast addresses,
and ranges for different rows must be disjoint.
"
::= { smfConfigurationGroup 13 }
smfConfiguredAddrForwardingEntry OBJECT-TYPE
SYNTAX SmfConfiguredAddrForwardingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) containing the information on a
particular multicast scope."
INDEX { smfConfiguredAddrForwardingAddrType,
Cole, et al. Expires September 1, 2009 [Page 20]
Internet-Draft The SMF MIB February 2009
smfConfiguredAddrForwardingFirstAddr }
::= { smfConfiguredAddrForwardingTable 1 }
SmfConfiguredAddrForwardingEntry ::= SEQUENCE {
smfConfiguredAddrForwardingAddrType InetAddressType,
smfConfiguredAddrForwardingFirstAddr InetAddress,
smfConfiguredAddrForwardingLastAddr InetAddress,
smfConfiguredAddrForwardingStatus RowStatus
}
smfConfiguredAddrForwardingAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the addresses in the multicast forwarding
range. Legal values correspond to the subset of
address families for which multicast address allocation
is supported."
::= { smfConfiguredAddrForwardingEntry 1 }
smfConfiguredAddrForwardingFirstAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(0..20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The first address in the multicast scope range. The type
of this address is determined by the value of the
smfConfiguredAddrForwardingAddrType object."
::= { smfConfiguredAddrForwardingEntry 2 }
smfConfiguredAddrForwardingLastAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(0..20))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The last address in the multicast scope range.
The type of this address is determined by the
value of the smfConfiguredAddrForwardingAddrType
object."
::= { smfConfiguredAddrForwardingEntry 3 }
smfConfiguredAddrForwardingStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
Cole, et al. Expires September 1, 2009 [Page 21]
Internet-Draft The SMF MIB February 2009
created, or old entries deleted from this table. If write
access is supported, the other writable objects in this
table may be modified even while the status is `active'."
::= { smfConfiguredAddrForwardingEntry 4 }
--
-- SMF Interfaces Configuration Table
--
smfInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF Interface Table describes the SMF
interfaces that are participating in the
SMF packet forwarding process. The ifIndex is
from the interfaces group defined in the
Interfaces Group MIB.
"
REFERENCE
"RFC 2863 - The Interfaces Group MIB, McCloghrie,
K., and F. Kastenholtz, June 2000."
::= { smfConfigurationGroup 14 }
smfInterfaceEntry OBJECT-TYPE
SYNTAX SmfInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF interface entry describes one SMF
interface as indexed by its ifIndex."
INDEX { smfIfIndex }
::= { smfInterfaceTable 1 }
SmfInterfaceEntry ::=
SEQUENCE {
smfIfIndex InterfaceIndexOrZero,
smfIfAdminStatus Status,
smfIfRowStatus RowStatus
}
smfIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
Cole, et al. Expires September 1, 2009 [Page 22]
Internet-Draft The SMF MIB February 2009
DESCRIPTION
"The ifIndex for this SMF interface."
::= { smfInterfaceEntry 1 }
smfIfAdminStatus OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SMF interface's administrative status.
The value 'enabled' denotes that the interface
is running the SMF forwarding process.
The value 'disabled' denotes that the interface is
external to the SMF forwarding process.
"
::= { smfInterfaceEntry 2 }
smfIfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table
by facilitating actions such as row creation,
construction, and destruction. The value of
this object has no effect on whether other
objects in this conceptual row can be
modified."
::= { smfInterfaceEntry 3 }
--
-- SMF Gateway Filter Table
-- (Note: Not sure at this point what to do with this
-- table. Most likely want to move to a seperate MIB.)
--
smfGatewayFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfGatewayFilterEntry
MAX-ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"The SMF Gateway can be configured to filter
multicast packets into and outof the SMF
MANET domain. This table defines the filter
rules which define packet matching and
related actions. The rules are in order ..."
Cole, et al. Expires September 1, 2009 [Page 23]
Internet-Draft The SMF MIB February 2009
REFERENCE
"The SMF draft."
::= { smfConfigurationGroup 15 }
smfGatewayFilterEntry OBJECT-TYPE
SYNTAX SmfGatewayFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single entry in the smfGatewayFilterTable."
REFERENCE
"The SMF draft."
INDEX { smfGatewayFilterIndex }
::= { smfGatewayFilterTable 1 }
SmfGatewayFilterEntry ::=
SEQUENCE {
smfGatewayFilterIndex InterfaceIndexOrZero,
smfGatewayFilterIf InterfaceIndexOrZero,
smfGatewayFilterIfDirection INTEGER,
smfGatewayFilterRuleRank Integer32,
smfGatewayFilterDestAddrType InetAddressType,
smfGatewayFilterDestAddr InetAddress,
smfGatewayFilterDestAddrPrefixLen InetAddressPrefixLength,
smfGatewayFilterSrcAddrType InetAddressType,
smfGatewayFilterSrcAddr InetAddress,
smfGatewayFilterSrcAddrPrefixLen InetAddressPrefixLength,
smfGatewayFilterProtocolNumber Integer32,
smfGatewayFilterDestPortNumber Integer32,
smfGatewayFilterAction INTEGER,
smfGatewayFilterRowStatus RowStatus
}
smfGatewayFilterIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Index for this filter rule.
"
::= { smfGatewayFilterEntry 1 }
smfGatewayFilterIf OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The ifIndex for this node interface
Cole, et al. Expires September 1, 2009 [Page 24]
Internet-Draft The SMF MIB February 2009
that is filtering this rule."
::= { smfGatewayFilterEntry 2 }
smfGatewayFilterIfDirection OBJECT-TYPE
SYNTAX INTEGER {
in(1),
out(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The ifIndex direction for this interface
filtering rule."
::= { smfGatewayFilterEntry 3 }
smfGatewayFilterRuleRank OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The rank of the rule specified in
this entry. This rank is specified by
the management application. The rules applied
on this device are rank ordered by this
rank, from smallest (applied first) to
largest (applied last). The rule ranks do not
have to be contiguous, but they must be unique.
When a management application changes this rank
and the new rank is identical to the rank of another
entry, then that entry's rank and all other entries
with a rank greater than this rank must be incremented
by one.
"
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 4 }
smfGatewayFilterDestAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the DestAddr, as defined
in the InetAddress MIB [RFC 4001]."
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 5 }
Cole, et al. Expires September 1, 2009 [Page 25]
Internet-Draft The SMF MIB February 2009
smfGatewayFilterDestAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination IP address of this rule. The type
of this address is determined by the value of the
smfGatewayFilterDestAddrType object."
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 6 }
smfGatewayFilterDestAddrPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
smfGatewayFilterDestAddr field."
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 7 }
smfGatewayFilterSrcAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the SrcAddr, as defined
in the InetAddress MIB [RFC 4001]."
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 8 }
smfGatewayFilterSrcAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source IP address of this rule. The type
of this address is determined by the value of the
smfGatewayFilterSrcAddrType object."
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 9 }
Cole, et al. Expires September 1, 2009 [Page 26]
Internet-Draft The SMF MIB February 2009
smfGatewayFilterSrcAddrPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
smfGatewayFilterSrcAddr field."
REFERENCE
"The SMF draft."
::= { smfGatewayFilterEntry 10 }
-- Note: check out the necessary range for protocol
-- and port numbers.
smfGatewayFilterProtocolNumber OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Protocol Number defined in RFC 5237."
::= { smfGatewayFilterEntry 11 }
smfGatewayFilterDestPortNumber OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination Port Number defined in
RFC XXXX."
::= { smfGatewayFilterEntry 12 }
smfGatewayFilterAction OBJECT-TYPE
SYNTAX INTEGER {
drop(1),
pass(2),
other(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The action to be taken if the rule is
matched."
::= { smfGatewayFilterEntry 13 }
smfGatewayFilterRowStatus OBJECT-TYPE
SYNTAX RowStatus
Cole, et al. Expires September 1, 2009 [Page 27]
Internet-Draft The SMF MIB February 2009
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table
by facilitating actions such as row creation,
construction, and destruction. The value of
this object has no effect on whether other
objects in this conceptual row can be
modified."
::= { smfGatewayFilterEntry 14 }
--
-- smfStateGroup
--
-- Contains information describing the current state of the SMF
-- process such as the current inclusion in the RS or not.
--
smfStateGroup OBJECT IDENTIFIER ::= { smfMIBObjects 3 }
smfNodeRsStatusIncluded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current status of the SMF node in the context of
the MANETs relay set. A value of true(1) indicates
that the node is currently part of the MANET Relay
Set. A value of false(2) indicates that the node
is currently not part of the MANET Relay Set."
::= { smfStateGroup 1 }
smfDpdMemoryOverflow OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the memory for caching
records for DPD overran and records had to be flushed.
The number of records to be flushed upon a buffer
overflow is an implementation specific decision.
"
::= { smfStateGroup 2 }
Cole, et al. Expires September 1, 2009 [Page 28]
Internet-Draft The SMF MIB February 2009
--
-- Dynamically Discovered Multicast Addr Table
--
smfDiscoveredAddrForwardingTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfDiscoveredAddrForwardingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing information on multicast
addresses which are to be forwarded by the SMF process.
Entries in this table are configured. As well, addresses
to be forwarded by the SMF device can be dynamically discovered
by other means. The corresponding state table,
smfDiscoveredAddrForwardingTable contains
these additional, dynamically discovered address for
forwarding.
Each row is associated with a range of multicast addresses,
and ranges for different rows must be disjoint.
"
::= { smfStateGroup 3 }
smfDiscoveredAddrForwardingEntry OBJECT-TYPE
SYNTAX SmfDiscoveredAddrForwardingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) containing the information on a
particular multicast scope."
INDEX { smfDiscoveredAddrForwardingAddrType,
smfDiscoveredAddrForwardingFirstAddr }
::= { smfDiscoveredAddrForwardingTable 1 }
SmfDiscoveredAddrForwardingEntry ::= SEQUENCE {
smfDiscoveredAddrForwardingAddrType InetAddressType,
smfDiscoveredAddrForwardingFirstAddr InetAddress,
smfDiscoveredAddrForwardingLastAddr InetAddress,
smfDiscoveredAddrForwardingStatus RowStatus
}
smfDiscoveredAddrForwardingAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the addresses in the multicast forwarding
Cole, et al. Expires September 1, 2009 [Page 29]
Internet-Draft The SMF MIB February 2009
range. Legal values correspond to the subset of
address families for which multicast address allocation
is supported."
::= { smfDiscoveredAddrForwardingEntry 1 }
smfDiscoveredAddrForwardingFirstAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(0..20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The first address in the multicast scope range. The type
of this address is determined by the value of the
smfConfiguredAddrForwardingAddrType object."
::= { smfDiscoveredAddrForwardingEntry 2 }
smfDiscoveredAddrForwardingLastAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(0..20))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The last address in the multicast scope range.
The type of this address is determined by the
value of the smfConfiguredAddrForwardingAddrType
object."
::= { smfDiscoveredAddrForwardingEntry 3 }
smfDiscoveredAddrForwardingStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table. If write
access is supported, the other writable objects in this
table may be modified even while the status is `active'."
::= { smfDiscoveredAddrForwardingEntry 4 }
--
-- SMF Neighbor Table
--
smfNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Cole, et al. Expires September 1, 2009 [Page 30]
Internet-Draft The SMF MIB February 2009
"The SMF NeighborTable describes the
current neighbor nodes, their address
and SMF RSSA and the interface on which
they can be reached."
REFERENCE
"Simplified Multicast Forwarding for MANET
(SMF), Macker, J., February 2008.
Section 7: SMF Neighborhood Discovery
Requirements."
::= { smfStateGroup 4 }
smfNeighborEntry OBJECT-TYPE
SYNTAX SmfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF Neighbor Table contains the
set of one-hop neighbors, the interface
they are reachable on and the SMF RSSA
they are currently running."
INDEX { smfNeighborIpAddrType,
smfNeighborIpAddr,
smfNeighborPrefixLen }
::= { smfNeighborTable 1 }
SmfNeighborEntry ::=
SEQUENCE {
smfNeighborIpAddrType InetAddressType,
smfNeighborIpAddr InetAddress,
smfNeighborPrefixLen InetAddressPrefixLength,
smfNeighborRSSA SmfRssaID,
smfNeighborNextHopInterface InterfaceIndexOrZero
}
smfNeighborIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The neighbor IP address type."
::= { smfNeighborEntry 1 }
smfNeighborIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The neighbor Inet IPv4 or IPv6 address."
Cole, et al. Expires September 1, 2009 [Page 31]
Internet-Draft The SMF MIB February 2009
::= { smfNeighborEntry 2 }
smfNeighborPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The prefix length. This is a decimal value that
indicates the number of contiguous, higher-order
bits of the address that make up the network
portion of the address."
::= { smfNeighborEntry 3 }
smfNeighborRSSA OBJECT-TYPE
SYNTAX SmfRssaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current RSSA running on the neighbor.
The list is identical to that described
above for the smfRssa object."
::= { smfNeighborEntry 4 }
smfNeighborNextHopInterface OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interface ifIndex over which the
neighbor is reachable in one-hop."
::= { smfNeighborEntry 5 }
--
-- SMF Performance Group
--
-- Contains objects which help to characterize the
-- performance of the SMF RSSA process, such as statistics
-- counters. There are two types of SMF RSSA statistics:
-- global counters and per interface counters.
--
smfPerformanceGroup OBJECT IDENTIFIER ::= { smfMIBObjects 4 }
smfGlobalPerfGroup OBJECT IDENTIFIER ::= { smfPerformanceGroup 1 }
Cole, et al. Expires September 1, 2009 [Page 32]
Internet-Draft The SMF MIB February 2009
--
-- IPv4 packet counters
--
smfIpv4MultiPktsRecvTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of
multicast IPv4 packets received by the
device."
::= { smfGlobalPerfGroup 1 }
smfIpv4MultiPktsForwardedTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of
multicast IPv4 packets forwarded by the
device."
::= { smfGlobalPerfGroup 2 }
smfIpv4DuplMultiPktsDetectedTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of duplicate
multicast IPv4 packets detected by the
device."
::= { smfGlobalPerfGroup 3 }
smfIpv4DroppedMultiPktsTTLExceededTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of dropped
multicast IPv4 packets by the
device due to TTL exceeded."
::= { smfGlobalPerfGroup 4 }
smfIpv4TTLLargerThanPreviousTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Cole, et al. Expires September 1, 2009 [Page 33]
Internet-Draft The SMF MIB February 2009
DESCRIPTION
"A counter of the total number of IPv4 packets
recieved which have a TTL larger than that
of a previously recived identical packet.
"
::= { smfGlobalPerfGroup 5 }
--
-- IPv6 packet counters
--
smfIpv6MultiPktsRecvTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of
multicast IPv6 packets received by the
device."
::= { smfGlobalPerfGroup 6 }
smfIpv6MultiPktsForwardedTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of
multicast IPv6 packets forwarded by the
device."
::= { smfGlobalPerfGroup 7 }
smfIpv6DuplMultiPktsDetectedTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of duplicate
multicast IPv6 packets detected by the
device."
::= { smfGlobalPerfGroup 8 }
smfIpv6DroppedMultiPktsTTLExceededTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of dropped
multicast IPv6 packets by the
Cole, et al. Expires September 1, 2009 [Page 34]
Internet-Draft The SMF MIB February 2009
device due to TTL exceeded."
::= { smfGlobalPerfGroup 9 }
smfIpv6TTLLargerThanPreviousTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv6 packets
recieved which have a TTL larger than that
of a previously recived identical packet.
"
::= { smfGlobalPerfGroup 10 }
smfIpv6HAVAssistsReqdTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv6 packets
recieved which required the HAV assist for DPD.
"
::= { smfGlobalPerfGroup 11 }
smfIpv6DpdHeaderInsertionsTotal OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv6 packets
recieved which the device inserted the
DPD header option.
"
::= { smfGlobalPerfGroup 12 }
--
-- Per SMF Interface Performance Table
--
smfInterfacePerfGroup OBJECT IDENTIFIER ::= { smfPerformanceGroup 2 }
smfIpv4InterfacePerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfIpv4InterfacePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF Interface Performance Table
Cole, et al. Expires September 1, 2009 [Page 35]
Internet-Draft The SMF MIB February 2009
describes the SMF statistics per
interface."
::= { smfInterfacePerfGroup 1 }
smfIpv4InterfacePerfEntry OBJECT-TYPE
SYNTAX SmfIpv4InterfacePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF Interface Performance entry
describes the statistics for a particular
node interface."
INDEX { smfIpv4IfPerfIfIndex }
::= { smfIpv4InterfacePerfTable 1 }
SmfIpv4InterfacePerfEntry ::=
SEQUENCE {
smfIpv4IfPerfIfIndex InterfaceIndexOrZero,
smfIpv4MultiPktsRecvPerIf Counter32,
smfIpv4MultiPktsForwardedPerIf Counter32,
smfIpv4DuplMultiPktsDetectedPerIf Counter32,
smfIpv4DroppedMultiPktsTTLExceededPerIf Counter32,
smfIpv4TTLLargerThanPreviousPerIf Counter32
}
smfIpv4IfPerfIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex for this node interface
that is collecting this set of
performance management statistics."
::= { smfIpv4InterfacePerfEntry 1 }
smfIpv4MultiPktsRecvPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the number of
multicast IP packets received by the
device on this interface."
::= { smfIpv4InterfacePerfEntry 2 }
smfIpv4MultiPktsForwardedPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Cole, et al. Expires September 1, 2009 [Page 36]
Internet-Draft The SMF MIB February 2009
STATUS current
DESCRIPTION
"A counter of the number of
multicast IP packets forwarded by the
device on this interface."
::= { smfIpv4InterfacePerfEntry 3 }
smfIpv4DuplMultiPktsDetectedPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the number of duplicate
multicast IP packets detected by the
device on this interface."
::= { smfIpv4InterfacePerfEntry 4 }
smfIpv4DroppedMultiPktsTTLExceededPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of dropped
multicast IPv4 packets by the
device due to TTL exceeded."
::= { smfIpv4InterfacePerfEntry 5 }
smfIpv4TTLLargerThanPreviousPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv4 packets
recieved which have a TTL larger than that
of a previously recived identical packet.
"
::= { smfIpv4InterfacePerfEntry 6 }
smfIpv6InterfacePerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfIpv6InterfacePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF Interface Performance Table
describes the SMF statistics per
interface."
::= { smfInterfacePerfGroup 2 }
Cole, et al. Expires September 1, 2009 [Page 37]
Internet-Draft The SMF MIB February 2009
smfIpv6InterfacePerfEntry OBJECT-TYPE
SYNTAX SmfIpv6InterfacePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SMF Interface Performance entry
describes the statistics for a particular
node interface."
INDEX { smfIpv6IfPerfIfIndex }
::= { smfIpv6InterfacePerfTable 1 }
SmfIpv6InterfacePerfEntry ::=
SEQUENCE {
smfIpv6IfPerfIfIndex InterfaceIndexOrZero,
smfIpv6MultiPktsRecvPerIf Counter32,
smfIpv6MultiPktsForwardedPerIf Counter32,
smfIpv6DuplMultiPktsDetectedPerIf Counter32,
smfIpv6DroppedMultiPktsTTLExceededPerIf Counter32,
smfIpv6TTLLargerThanPreviousPerIf Counter32,
smfIpv6HAVAssistsReqdPerIf Counter32,
smfIpv6DpdHeaderInsertionsPerIf Counter32
}
smfIpv6IfPerfIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex for this node interface
that is collecting this set of
performance management statistics.
For packets generated locally at
this node, performance counters
are assigned to the loopback
interface.
"
::= { smfIpv6InterfacePerfEntry 1 }
smfIpv6MultiPktsRecvPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the number of
multicast IP packets received by the
device on this interface."
::= { smfIpv6InterfacePerfEntry 2 }
Cole, et al. Expires September 1, 2009 [Page 38]
Internet-Draft The SMF MIB February 2009
smfIpv6MultiPktsForwardedPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the number of
multicast IP packets forwarded by the
device on this interface."
::= { smfIpv6InterfacePerfEntry 3 }
smfIpv6DuplMultiPktsDetectedPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the number of duplicate
multicast IP packets detected by the
device on this interface."
::= { smfIpv6InterfacePerfEntry 4 }
smfIpv6DroppedMultiPktsTTLExceededPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the number of dropped
multicast IP packets by the
device on this interface due to TTL
exceeded."
::= { smfIpv6InterfacePerfEntry 5 }
smfIpv6TTLLargerThanPreviousPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv6 packets
recieved which have a TTL larger than that
of a previously recived identical packet.
"
::= { smfIpv6InterfacePerfEntry 6 }
smfIpv6HAVAssistsReqdPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv6 packets
Cole, et al. Expires September 1, 2009 [Page 39]
Internet-Draft The SMF MIB February 2009
recieved which required the HAV assist for DPD.
"
::= { smfIpv6InterfacePerfEntry 7 }
smfIpv6DpdHeaderInsertionsPerIf OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A counter of the total number of IPv6 packets
recieved which the device inserted the
DPD header option.
"
::= { smfIpv6InterfacePerfEntry 8 }
--
-- Reports Control
-- This and the following tables are modeled
-- after the report control and collection
-- capabilities found in RMON II, RFC XXXX
--
-- Note: Starting down this road only for general performance
-- measures first. If desireable, then will add reports for
-- IF specific measurements.
--
smfReportsGroup OBJECT IDENTIFIER ::= { smfMIBObjects 5 }
smfGenReportCntrlTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfGenReportCntrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The smfGenReportCntrlTable is the controlling entry
that manages the population of studies in the
Report for selected time intervals.
Note that this is not like the typical RMON
controlTable and dataTable in which each entry creates
its own data table. Each entry in this table enables the
creation of multiple data tables on a study basis. For each
interval, the study is updated in place, and the current
data content of the table becomes invalid.
The control table entries are persistent across
system reboots."
::= { smfReportsGroup 1 }
Cole, et al. Expires September 1, 2009 [Page 40]
Internet-Draft The SMF MIB February 2009
smfGenReportCntrlEntry OBJECT-TYPE
SYNTAX SmfGenReportCntrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the smfGenReportCntrlTable.
An example of the indexing of this entry is
smfGenReportCntrInterval.1"
INDEX { smfGenReportCntrlIndex }
::= { smfGenReportCntrlTable 1 }
SmfGenReportCntrlEntry ::= SEQUENCE {
smfGenReportCntrlIndex Unsigned32,
smfGenReportCntrlInterval Unsigned32,
smfGenReportCntrlReqSize Unsigned32,
smfGenReportCntrlGrantedSize Unsigned32,
smfGenReportCntrlReqReports Unsigned32,
smfGenReportCntrlGrantedReports Unsigned32,
smfGenReportCntrlStartTime TimeStamp,
smfGenReportCntrlReportNumber Unsigned32,
smfGenReportCntrlInsertsDenied Counter32,
smfGenReportCntrlOwner OwnerString,
smfGenReportCntrlStorageType StorageType,
smfGenReportCntrlStatus RowStatus
}
smfGenReportCntrlIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
smfGenReportCntrlTable. Each such entry defines a unique
report whose results are placed in the smfGenReportTable on
behalf of this smfGenReportCntrlEntry."
::= { smfGenReportCntrlEntry 1 }
smfGenReportCntrlInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The interval in seconds over which data is accumulated before
being aggregated into a report in the smfGenReportTable.
All reports with the same smfGenReportCntrlIndex will be
Cole, et al. Expires September 1, 2009 [Page 41]
Internet-Draft The SMF MIB February 2009
based on the same interval.
This object may not be modified if the associated
smfGenReportCntrlStatus object is equal to active(1)."
DEFVAL { 3600 }
::= { smfGenReportCntrlEntry 2 }
smfGenReportCntrlReqSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of Client and Server combination
entries requested for this report.
When this object is created or modified, the probe
should set smfGenReportCntrlGrantedSize as closely to this
object as is possible for the particular probe
implementation and available resources.
It is important to note that this value is the number of
requested entries in the smfGenReportTable only.
This object may not be modified if the associated
smfGenReportCntrlStatus object is equal to active(1)."
::= { smfGenReportCntrlEntry 3 }
smfGenReportCntrlGrantedSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of performance entries in this report.
When the associated smfGenReportCntrlReqSize object is
created or modified, the probe should set this
object as closely to the requested value as is
possible for the particular implementation and
available resources. The probe must not lower this
value except as a result of a set to the associated
smfGenReportCntrlReqSize object.
It is an implementation-specific matter as to whether
zero-valued entries are available."
::= { smfGenReportCntrlEntry 4 }
smfGenReportCntrlReqReports OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
Cole, et al. Expires September 1, 2009 [Page 42]
Internet-Draft The SMF MIB February 2009
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of saved reports requested to be allocated on
behalf of this entry.
This object may not be modified if the associated
smfGenReportCntrlStatus object is equal to active(1)."
::= { smfGenReportCntrlEntry 5 }
smfGenReportCntrlGrantedReports OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of saved reports the agent has allocated based
on the requested amount in smfGenReportCntrlReqReports.
Because each report can have many entries, the total number
of entries allocated will be this number multiplied by the
value of smfGenReportCntrlGrantedSize, or by 1 if that
object doesn't exist.
When the associated smfGenReportCntrlReqReports object is
created or modified, the agent should set this object as
closely to the requested value as is possible for the
particular implementation and available resources. When
considering available resources, the agent must consider its
ability to allocate this many reports, each with the number
of entries represented by smfGenReportCntrlGrantedSize, or
by 1 if that object doesn't exist.
Note that although the storage required for each report may
fluctuate due to changing conditions, the agent must continue
to have storage available to satisfy the full report size for
all reports, when necessary. Further, the agent must not
lower this value except as a result of a set to the
associated smfGenReportCntrlReqSize object."
::= { smfGenReportCntrlEntry 6 }
smfGenReportCntrlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when the system began processing the
report in progress. Note that the report in progress is not
available.
Cole, et al. Expires September 1, 2009 [Page 43]
Internet-Draft The SMF MIB February 2009
This object may be used by the management station to figure
out the start time for all previous reports saved for this
smfGenReportCntrlEntry, as reports are started at fixed
intervals."
::= { smfGenReportCntrlEntry 7 }
smfGenReportCntrlReportNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of the report in progress. When an
smfGenReportCntrlEntry is activated, the first report will
be numbered zero."
::= { smfGenReportCntrlEntry 8 }
smfGenReportCntrlInsertsDenied OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of attempts to add an entry to reports for
this SmfGenReportCntrlEntry that failed because the number
of entries would have exceeded smfGenReportCntrlGrantedSize.
This number is valuable in determining if enough entries have
been allocated for reports in light of fluctuating network
usage. Note that an entry that is denied will often be
attempted again, so this number will not predict the exact
number of additional entries needed, but it can be used to
understand the relative magnitude of the problem.
Also note that there is no ordering specified for the entries
in the report; thus, there are no rules for which entries
will be omitted when not enough entries are available. As a
consequence, the agent is not required to delete 'least
valuable' entries first."
::= { smfGenReportCntrlEntry 9 }
smfGenReportCntrlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is
therefore using the resources assigned to it.
This object may not be modified if the associated
Cole, et al. Expires September 1, 2009 [Page 44]
Internet-Draft The SMF MIB February 2009
smfGenReportCntrlStatus object is equal to active(1)."
::= { smfGenReportCntrlEntry 10 }
smfGenReportCntrlStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type of this smfGenReportCntrlEntry. If the
value of this object is 'permanent', no objects in this row
need to be writable."
::= { smfGenReportCntrlEntry 11 }
smfGenReportCntrlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this performance control entry.
An entry may not exist in the active state unless each
object in the entry has an appropriate value.
Once this object is set to active(1), no objects in the
smfGenReportCntrlTable can be changed.
If this object is not equal to active(1), all associated
entries in the smfGenReportTable shall be deleted."
::= { smfGenReportCntrlEntry 12 }
--
-- Reports
-- (Note: This represents a rather conservative list
-- of objects for inclusion within offline report
-- generation. As discussions evolve, more objects
-- may be added to the below set.
--
-- Also, it is typical to use this construct to define
-- objects representing statistical information and not
-- counter associated information. We need to define a set
-- of statistical objects for these remote reports and
-- replace this place-holder set prior to finalizing this MIB.)
--
smfGenReportTable OBJECT-TYPE
SYNTAX SEQUENCE OF SmfGenReportEntry
MAX-ACCESS not-accessible
Cole, et al. Expires September 1, 2009 [Page 45]
Internet-Draft The SMF MIB February 2009
STATUS current
DESCRIPTION
"This table contains
studies for each of the control table entries in
smfGenReportCntrlTable. These studies are
provided based on the selections and parameters
found for the entry in the
smfGenReportCntrlTable.
The performance counter are the same as those
specified in the smfPerformanceGroup."
::= { smfReportsGroup 2 }
smfGenReportEntry OBJECT-TYPE
SYNTAX SmfGenReportEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the smfGenReportTable.
The smfGenReportCntrlIndex value in the index identifies the
smfGenReportCntrlEntry on whose behalf this entry was
created.
The smfGenReportIndex value in the index identifies which
report (in the series of reports) this entry is a part of.
An example of the indexing of this entry is
smfGenReportMultiPktsForwarded.3.15"
INDEX { smfGenReportCntrlIndex,
smfGenReportIndex
}
::= { smfGenReportTable 1 }
SmfGenReportEntry ::= SEQUENCE {
smfGenReportIndex Unsigned32,
smfGenReportIpv4MultiPktsRecvTot ZeroBasedCounter32,
smfGenReportIpv4MultiPktsForwardedTot ZeroBasedCounter32,
smfGenReportIpv4DuplMultiPktsDetectedTot ZeroBasedCounter32,
smfGenReportIpv4DroppedMultiPktsTTLExceededTot ZeroBasedCounter32
}
smfGenReportIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of smfGenReportCntrlNumber for the report to
Cole, et al. Expires September 1, 2009 [Page 46]
Internet-Draft The SMF MIB February 2009
which this entry belongs."
::= { smfGenReportEntry 1 }
smfGenReportIpv4MultiPktsRecvTot OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of the total number of ...."
::= { smfGenReportEntry 2 }
smfGenReportIpv4MultiPktsForwardedTot OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of the total number of ...."
::= { smfGenReportEntry 3 }
smfGenReportIpv4DuplMultiPktsDetectedTot OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of the total number of ...."
::= { smfGenReportEntry 4 }
smfGenReportIpv4DroppedMultiPktsTTLExceededTot OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of the total number of ...."
::= { smfGenReportEntry 5 }
--
-- Notifications
--
-- Note: What notifications do we want for this MIB?
--
-- Compliance Statements
--
Cole, et al. Expires September 1, 2009 [Page 47]
Internet-Draft The SMF MIB February 2009
-- Note: need to update the Compliance section once the mib
-- objects stablize.
smfCompliances OBJECT IDENTIFIER ::= { smfMIBConformance 1 }
smfMIBGroups OBJECT IDENTIFIER ::= { smfMIBConformance 2 }
smfBasicCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The basic implementation requirements for
managed network entities that implement
the SMF RSSA process."
MODULE -- this module
MANDATORY-GROUPS { smfCapabObjectsGroup,
smfConfigObjectsGroup }
::= { smfCompliances 1 }
smfFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The full implementation requirements for
managed network entities that implement
the SMF RSSA process."
MODULE -- this module
MANDATORY-GROUPS { smfCapabObjectsGroup,
smfConfigObjectsGroup,
smfStateObjectsGroup,
smfPerfObjectsGroup,
smfRepObjectsGroup }
::= { smfCompliances 2 }
--
-- Units of Conformance
--
smfCapabObjectsGroup OBJECT-GROUP
OBJECTS {
smfOpModeCapabilitiesName,
smfOpModeCapabilitiesReference,
smfRssaCapabilitiesName,
smfRssaCapabilitiesReference
}
STATUS current
DESCRIPTION
"Set of SMF configuration objects implemented
in this module."
::= { smfMIBGroups 1 }
Cole, et al. Expires September 1, 2009 [Page 48]
Internet-Draft The SMF MIB February 2009
smfConfigObjectsGroup OBJECT-GROUP
OBJECTS {
smfAdminStatus,
smfConfiguredOpMode,
smfConfiguredRssa,
smfRssaMember,
smfIpv4Dpd,
smfIpv6Dpd,
smfMaxPktLifetime,
smfDpdMaxMemorySize,
smfDpdEntryMaxLifetime,
smfNhdpRssaMesgTLVIncluded,
smfNhdpRssaAddrBlockTLVIncluded,
smfNhdpRouterPriorityTLVIncluded,
smfConfiguredAddrForwardingLastAddr,
smfConfiguredAddrForwardingStatus,
smfIfAdminStatus,
smfIfRowStatus,
smfGatewayFilterIf,
smfGatewayFilterIfDirection,
smfGatewayFilterRuleRank,
smfGatewayFilterDestAddrType,
smfGatewayFilterDestAddr,
smfGatewayFilterDestAddrPrefixLen,
smfGatewayFilterSrcAddrType,
smfGatewayFilterSrcAddr,
smfGatewayFilterSrcAddrPrefixLen,
smfGatewayFilterProtocolNumber,
smfGatewayFilterDestPortNumber,
smfGatewayFilterAction,
smfGatewayFilterRowStatus
}
STATUS current
DESCRIPTION
"Set of SMF configuration objects implemented
in this module."
::= { smfMIBGroups 2 }
smfStateObjectsGroup OBJECT-GROUP
OBJECTS {
smfNodeRsStatusIncluded,
smfDpdMemoryOverflow,
smfDiscoveredAddrForwardingLastAddr,
smfDiscoveredAddrForwardingStatus,
Cole, et al. Expires September 1, 2009 [Page 49]
Internet-Draft The SMF MIB February 2009
smfNeighborRSSA,
smfNeighborNextHopInterface
}
STATUS current
DESCRIPTION
"Set of SMF state objects implemented
in this module."
::= { smfMIBGroups 3 }
smfPerfObjectsGroup OBJECT-GROUP
OBJECTS {
smfIpv4MultiPktsRecvTotal,
smfIpv4MultiPktsForwardedTotal,
smfIpv4DuplMultiPktsDetectedTotal,
smfIpv4DroppedMultiPktsTTLExceededTotal,
smfIpv4TTLLargerThanPreviousTotal,
smfIpv6MultiPktsRecvTotal,
smfIpv6MultiPktsForwardedTotal,
smfIpv6DuplMultiPktsDetectedTotal,
smfIpv6DroppedMultiPktsTTLExceededTotal,
smfIpv6TTLLargerThanPreviousTotal,
smfIpv6HAVAssistsReqdTotal,
smfIpv6DpdHeaderInsertionsTotal,
smfIpv4MultiPktsRecvPerIf,
smfIpv4MultiPktsForwardedPerIf,
smfIpv4DuplMultiPktsDetectedPerIf,
smfIpv4DroppedMultiPktsTTLExceededPerIf,
smfIpv4TTLLargerThanPreviousPerIf,
smfIpv6MultiPktsRecvPerIf,
smfIpv6MultiPktsForwardedPerIf,
smfIpv6DuplMultiPktsDetectedPerIf,
smfIpv6DroppedMultiPktsTTLExceededPerIf,
smfIpv6TTLLargerThanPreviousPerIf,
smfIpv6HAVAssistsReqdPerIf,
smfIpv6DpdHeaderInsertionsPerIf
}
STATUS current
DESCRIPTION
"Set of SMF performance objects implemented
in this module by total and per interface."
::= { smfMIBGroups 4 }
smfRepObjectsGroup OBJECT-GROUP
OBJECTS {
smfGenReportCntrlInterval,
Cole, et al. Expires September 1, 2009 [Page 50]
Internet-Draft The SMF MIB February 2009
smfGenReportCntrlReqSize,
smfGenReportCntrlGrantedSize,
smfGenReportCntrlReqReports,
smfGenReportCntrlGrantedReports,
smfGenReportCntrlStartTime,
smfGenReportCntrlReportNumber,
smfGenReportCntrlInsertsDenied,
smfGenReportCntrlOwner,
smfGenReportCntrlStorageType,
smfGenReportCntrlStatus,
smfGenReportIpv4MultiPktsRecvTot,
smfGenReportIpv4MultiPktsForwardedTot,
smfGenReportIpv4DuplMultiPktsDetectedTot,
smfGenReportIpv4DroppedMultiPktsTTLExceededTot
}
STATUS current
DESCRIPTION
"Set of SMF reports objects implemented
in this module."
::= { smfMIBGroups 5 }
END
8. Security Considerations
[TODO] Each specification that defines one or more MIB modules MUST
contain a section that discusses security considerations relevant to
those modules. This section MUST be patterned after the latest
approved template (available at
http://www.ops.ietf.org/mib-security.html). Remember that the
objective is not to blindly copy text from the template, but rather
to think and evaluate the risks/vulnerabilities and then state/
document the result of this evaluation.
[TODO] if you have any read-write and/or read-create objects, please
include the following boilerplate paragraph.
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
Cole, et al. Expires September 1, 2009 [Page 51]
Internet-Draft The SMF MIB February 2009
o [TODO] writable MIB objects that could be especially disruptive if
abused MUST be explicitly listed by name and the associated
security risks MUST be spelled out; RFC 2669 has a very good
example.
o [TODO] list the writable tables and objects and state why they are
sensitive.
[TODO] else if there are no read-write objects in your MIB module,
use the following boilerplate paragraph.
There are no management objects defined in this MIB module that have
a MAX-ACCESS clause of read-write and/or read-create. So, if this
MIB module is implemented correctly, then there is no risk that an
intruder can alter or create any management objects of this MIB
module via direct SNMP SET operations.
[TODO] if you have any sensitive readable objects, please include the
following boilerplate paragraph.
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o [TODO] you must explicitly list by name any readable objects that
are sensitive or vulnerable and the associated security risks MUST
be spelled out (for instance, if they might reveal customer
information or violate personal privacy laws such as those of the
European Union if exposed to unauthorized parties)
o [TODO] list the tables and objects and state why they are
sensitive.
[TODO] discuss what security the protocol used to carry the
information should have. The following three boilerplate paragraphs
should not be changed without very good reason. Changes will almost
certainly require justification during IESG review.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
Cole, et al. Expires September 1, 2009 [Page 52]
Internet-Draft The SMF MIB February 2009
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
9. IANA Considerations
[TODO] In order to comply with IESG policy as set forth in
http://www.ietf.org/ID-Checklist.html, every Internet-Draft that is
submitted to the IESG for publication MUST contain an IANA
Considerations section. The requirements for this section vary
depending what actions are required of the IANA. see RFC4181 section
3.5 for more information on writing an IANA clause for a MIB module
document.
[TODO] select an option and provide the necessary details.
Option #1:
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
sampleMIB { mib-2 XXX }
Option #2:
Editor's Note (to be removed prior to publication): the IANA is
requested to assign a value for "XXX" under the 'mib-2' subtree and
to record the assignment in the SMI Numbers registry. When the
assignment has been made, the RFC Editor is asked to replace "XXX"
(here and in the MIB module) with the assigned value and to remove
this note.
Note well: prior to official assignment by the IANA, a draft document
MUST use placeholders (such as "XXX" above) rather than actual
numbers. See RFC4181 Section 4.5 for an example of how this is done
Cole, et al. Expires September 1, 2009 [Page 53]
Internet-Draft The SMF MIB February 2009
in a draft MIB module.
Option #3:
This memo includes no request to IANA.
10. Contributors
This MIB document uses the template authored by D. Harrington which
is based on contributions from the MIB Doctors, especially Juergen
Schoenwaelder, Dave Perkins, C.M.Heard and Randy Presuhn.
11. Acknowledgements
12. References
12.1. Normative References
[RFC2863] McCloghrie, K. and F. Kastenholz, "The
Interfaces Group MIB", RFC 2863, June 2000.
[RFC3418] Presuhn, R., "Management Information Base (MIB)
for the Simple Network Management Protocol
(SNMP)", STD 62, RFC 3418, December 2002.
[RFC2119] Bradner, S., "Key words for use in RFCs to
Indicate Requirement Levels", BCP 14, RFC 2119,
March 1997.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management
Information Version 2 (SMIv2)", STD 58,
RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J.
Schoenwaelder, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[I-D.ietf-manet-smf] Macker, J. and S. Team, "Simplified Multicast
Forwarding for MANET", draft-ietf-manet-smf-08
(work in progress), November 2008.
Cole, et al. Expires September 1, 2009 [Page 54]
Internet-Draft The SMF MIB February 2009
12.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B.
Stewart, "Introduction and Applicability
Statements for Internet-Standard Management
Framework", RFC 3410, December 2002.
Appendix A. Change Log
Not applicable to draft 00
1.
Appendix B. Open Issues
This section contains the set of open issues related to the
development and design of the SMF-MIB. This section will not be
present in the final version of the MIB and will be removed once all
the open issues have been resolved.
1. Clarify handling of the NHDP TLV message inclusions?
2. Can we develop a capabilities table for the supported RSSA
algorithms? And, if so, can each supported RSSA have a
different set of configuration parameters?
3. Is the Gateway Filter table appropriate for this MIB or should
it be handled in a separate MIB worked elsewhere? How should
this table be indexed and how should it represent the ordering
of the rules (or chains)? Should this be greatly simplified?
How do we handle null values in the rules?
4. Is it useful to track the effectiveness of the coverage of the
current RSSA? Is it possible to track this?
5. Complete notification group.
6. Complete conformance group.
7. Work on the relationship to other MIBs, IF-MIB, NHDP-MIB.
8. Update the text of the document to reflect the final state of
the MIB.
9. Identify all objects requiring non-volatile storage in their
DESCRIPTION clauses.
Cole, et al. Expires September 1, 2009 [Page 55]
Internet-Draft The SMF MIB February 2009
10. Incorporate parameter relationship conditions into their
DESCRIPTION clauses.
11. Complete the security analysis and section.
12. Cleanup all the [TODOs] from the MIB template.
Appendix C.
***************************************************************
* Note to the RFC Editor (to be removed prior to publication) *
* *
* 1) The reference to RFCXXXX within the DESCRIPTION clauses *
* of the MIB module point to this draft and are to be *
* assigned by the RFC Editor. *
* *
* 2) The reference to RFCXXX2 throughout this document point *
* to the current draft-ietf-manet-smf-xx.txt. This *
* need to be replaced with the XXX RFC number. *
* *
***************************************************************
Authors' Addresses
Robert G. Cole
Johns Hopkins University
11100 Johns Hopkins Road, Room 257
Laurel, Maryland 21073
USA
Phone: +1 443 778 6951
EMail: robert.cole@jhuapl.edu
URI: http://www.cs.jhu.edu/~rgcole/
Joseph Macker
Naval Research Laboratory
Washington, D.C. 20375
USA
EMail: macker@itd.nrl.navy.mil
Cole, et al. Expires September 1, 2009 [Page 56]
Internet-Draft The SMF MIB February 2009
Brian Adamson
Naval Research Laboratory
Washington, D.C. 20375
USA
EMail: adamson@itd.nrl.navy.mil
Sean Harnedy
Booz Allen Hamilton
333 City Boulevard West
Orange, CA 92868
USA
EMail: harnedy_sean@bah.com
Cole, et al. Expires September 1, 2009 [Page 57]