Internet Engineering Task Force S. Combes
IPDVB WG P. Amundsen
M. Lambert
H-P. Lexow
Internet Draft SatLabs Group
Expires: January 2008 July 9, 2007
Category: Draft intended for INFORMATIONAL RFC
The DVB-RCS MIB
draft-combes-ipdvb-mib-rcs-01.doc
Status of this Memo
By submitting this Internet-Draft, each author represents that
any applicable patent or other IPR claims of which he or she is
aware have been or will be disclosed, and any of which he or she
becomes aware will be disclosed, in accordance with Section 6 of
BCP 79.
This document may not be modified, and derivative works of it may not
be created, except to publish it as an RFC and to translate it into
languages other than English, or to extract section 3 as-is for
separate use.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on January 9, .
Abstractf
This document describes the MIB module for the Digital Video
Broadcasting Return Channel via Satellite system (DVB-RCS). It
defines a set of new MIB entities to characterise the behaviour and
Combes Expires January 9, 2008 [Page 1]
Internet-Draft DVB-RCS MIB July 2007
performance of network layer entities deploying DVB-RCS.
Combes Expires January 9, 2008 [Page 2]
Internet-Draft DVB-RCS MIB July 2007
Table of Contents
1. Introduction...................................................3
2. Conventions used in this document..............................4
2.1. MIB Module................................................4
3. Definitions....................................................5
4. Security Considerations.......................................65
5. IANA Considerations...........................................65
6. Conclusions.........................Error! Bookmark not defined.
7. Acknowledgments...............................................65
8. References....................................................66
8.1. Normative References.....................................66
8.2. Informative References...................................66
9. Author's Addresses............................................67
Intellectual Property Statement..................................68
10. Disclaimer of Validity.......................................68
11. Copyright Statement..........................................69
1. Introduction
The SatLabs Group [SATLABS] is an international non-profit EEIG
(European Economic Interest Grouping) committed to large-scale
adoption and deployment of the Digital Video Broadcasting Return
Channel via Satellite (DVB-RCS) standard [ETSI-RCS]. SatLabs members
are service providers, satellite operators, system integrators,
terminal manufacturers and technology providers with an interest in
DVB-RCS.
Since its creation in 2001, the main goal of the SatLabs Group has
been to achieve interoperability between DVB-RCS terminals and
systems. Therefore, the Group has defined the SatLabs Qualification
Program which provides an independent certification process for DVB-
RCS Terminals based on System Recommendations defined by SatLabs. To
enhance products interoperability, beyond the physical and MAC layers
mechanisms defined in the DVB-RCS standard, SatLabs has expanded its
Recommendations in the field of DVB-RCS terminal management
[SATLABS]. As a part of this effort, SatLabs has specified a common
SNMP Management Information Base (MIB) for DVB-RCS terminals, which
is defined in this document.
Combes Expires January 9, 2008 [Page 3]
Internet-Draft DVB-RCS MIB July 2007
2. Conventions used in this document
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT"
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119. [RFC2119].
2.1. MIB Module
The MIB module in this document uses the following OBJECT IDENTIFIER values
assigned by IANA:
+------------+---------------------------+
| Descriptor | OBJECT IDENTIFIER value |
+------------+---------------------------+
|dvbrcsIfMib |{ mib-2 transmission 239 } |
+------------+---------------------------+
Table 1: Object Identifiers for the MIB
These values have been assigned for this MIB under the 'mib-2.transmission'
subtree.
Combes Expires January 9, 2008 [Page 4]
Internet-Draft DVB-RCS MIB July 2007
3. Definitions
DVBRCS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, transmission, NOTIFICATION-TYPE
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, DisplayString,
PhysAddress, RowStatus FROM SNMPv2-TC;
dvbrcsMIB MODULE-IDENTITY
LAST-UPDATED "200707061200Z"
ORGANIZATION "The SatLabs Group"
CONTACT-INFO
"The SatLabs Group
Web: www.satlabs.org
E-mail: info@satlabs.org "
DESCRIPTION
"DVB-RCS MIB subtree. Draft version B."
REVISION "200707061200Z"
DESCRIPTION
"Draft revision B of this MIB module."
::= { transmission 239 }
===================================================================
-- Textual Conventions
===================================================================
SatLabsOptionMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "This textual convention enumerates the declaration
of the SatLabs defined options.
(0) refers to the most significant bit."
REFERENCE "SatLabs System Recommendation version 2 available at
www.satlabs.org"
SYNTAX BITS {
mpegTrf(0),
coarseSync(1),
wideHop(2),
fastHop(3),
dynamicMfTdma(4),
routeId(5),
Combes Expires January 9, 2008 [Page 5]
Internet-Draft DVB-RCS MIB July 2007
contentionSync(6),
qpskLow(7),
mod16Apsk(8),
mod32Apsk(9),
normalFec(10),
multiTs(11),
gsTs(12),
enhQoS(13),
pep(14),
http(15),
ftp(16),
dhcp(17),
dns(18),
avbdcRep(19),
chIdStrict(20),
rcstPara(21),
nlid(22),
snmpAll(23),
installLog(24),
fwdLinkStatus(25),
enhClassifier(26),
spare1(27),
spare2(28),
spare3(29),
spare4(30),
spare5(31),
}
===================================================================
-- object type definitions
===================================================================
dvbrcsMIBObjects OBJECT IDENTIFIER ::= {dvbrcsMIB 1}
dvbrcsConformance OBJECT IDENTIFIER ::= {dvbrcsMIB 2}
rcst OBJECT IDENTIFIER ::= {dvbrcsMIBObjects 1}
fwdLink OBJECT IDENTIFIER ::= {dvbrcsMIBObjects 2}
rtnLink OBJECT IDENTIFIER ::= {dvbrcsMIBObjects 3}
rcstSystem OBJECT IDENTIFIER ::= {rcst 1}
rcstNetwork OBJECT IDENTIFIER ::= {rcst 2}
rcstInstall OBJECT IDENTIFIER ::= {rcst 3}
rcstQos OBJECT IDENTIFIER ::= {rcst 4}
rcstControl OBJECT IDENTIFIER ::= {rcst 5}
rcstState OBJECT IDENTIFIER ::= {rcst 6}
fwdConfig OBJECT IDENTIFIER ::= {fwdLink 1}
Combes Expires January 9, 2008 [Page 6]
Internet-Draft DVB-RCS MIB July 2007
fwdStatus OBJECT IDENTIFIER ::= {fwdLink 2}
rtnConfig OBJECT IDENTIFIER ::= {rtnLink 1}
rtnStatus OBJECT IDENTIFIER ::= {rtnLink 2}
===================================================================
-- rcstSystem sub-tree object types
===================================================================
systemMibRevision OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object allows the SNMP agent to report the implemented
MIB module revision.
The supported REVISION of this module is reported."
::= {rcstSystem 1}
===================================================================
-- options declared according to the textual conventions
===================================================================
systemSatlabsOptions OBJECT-TYPE
SYNTAX SatLabsOptionMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the options supported as defined in SatLabs system
recommendations version 2. A value of 1 indicates that the
respective option is supported. The mapping to the options is to be
understood as described here. (0) refers to the most significant
bit.
mpegTrf(0) -> MPEG_TRF
coarseSync(1) -> COARSE_SYNC
wideHop(2) -> WIDE_HOPP
fastHop(3) -> FAST_HOPP
dynamicMfTdma(4) -> Dynamic_MF_TDMA
routeId(5) -> ROUTE_ID
contentionSync(6) -> CONTENTION_SYNC
qpskLow(7) -> QPSKLOW
mod16Apsk(8) -> 16APSK
mod32Apsk(9) -> 32APSK
normalFec(10) -> NORMALFEC
Combes Expires January 9, 2008 [Page 7]
Internet-Draft DVB-RCS MIB July 2007
multiTs(11) -> MULTITS
gsTs(12) -> GSTS
enhQoS(13) -> ENHQOS
pep(14) -> PEP
http(15) -> HTTP
ftp(16) -> FTP
dhcp(17) -> DHCP
dns(18) -> DNS
avbdcRep(19) -> AVBDC_REP
chIdStrict(20) -> CHID_STRICT
rcstPara(21) -> RCST_PARA
nlid(22) -> NLID
snmpAll(23) -> SNMPALL
installLog(24) -> INSTALL_LOG
fwdLinkStatus(25) -> FWDLINKSTATUS
enhClassifier(26) -> ENHCLASSIFIER
The support of specific options mandates the support of specific
objects and access levels."
REFERENCE "SatLabs System Recommendation version 2 available at
www.satlabs.org"
::= {rcstSystem 2}
systemLocation OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The string shall have 31 characters in the following
format:
<xxxx.xxx>,<a>,<yyyyy.yyy>,<b>,<zzzz.z>,M
where x, y and z represents digits,
a=N or S,
b=E or W,
Reading the digits from left to right:
'x' - - 7 latitude digits;
x digits 1-2 contain the degrees,
x digits 3-7 contain the minutes in decimal;
'y' - - 8 longitude digits;
y digits 1-3 contain the degrees,
y digits 4-8 contain the minutes in decimal;
'z' 5 altitude digits; meters above sea level in decimal;
Combes Expires January 9, 2008 [Page 8]
Internet-Draft DVB-RCS MIB July 2007
'.' is the decimal point;
',' is the field separator;
'M' is the indicator for altitude meters.
This format is a modified subset of the NMEA 0183 format
for Global Positioning System Fix Data."
::= {rcstSystem 3}
systemOduAntennaSize OBJECT-TYPE
SYNTAX DisplayString
UNITS "cm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object gives the diameter of the antenna. This value
shall be given in centimeters. It is defined at
installation. The
object can be used in conjunction with environmental
requirements."
::= {rcstSystem 4}
systemOduAntennaGain OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBi"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This field describes the antenna peak gain of the ODU and
shall be defined by the installer. The gain shall be given
in tenth of dBi for more flexibility, i.e. 46.5 dBi will be
represented by 465. Defined at installation."
::= {rcstSystem 5}
systemOduSspa OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 W"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This field describes the SSPA installed in the ODU and
shall be defined by the installer. The power shall be given
in tenth of Watt for more flexibility, i.e. 0,5 W will be
represented by 5, 1 W by 10 and 2 W by 20.
Defined at installation."
Combes Expires January 9, 2008 [Page 9]
Internet-Draft DVB-RCS MIB July 2007
::= {rcstSystem 6}
systemOduTxType OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Describes the type of transmitter installed in the ODU."
::= {rcstSystem 7}
systemOduRxType OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Describes the type of LNB installed in the ODU, with
information such as vendor type, ouput type (single, twin,
quad,
), etc.. "
::= {rcstSystem 8}
systemOduRxBand OBJECT-TYPE
SYNTAX INTEGER {
oduHighRxBand (0),
oduLowRxBand (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Describes whether High Band or Low Band is selected in
the LNB. Specifying High Band results in activation of a
18-26 kHz tone with 0.4-0.8 Vpp in the Rx IFL cable:
(0) - High Band
(1) - Low Band "
::= {rcstSystem 9}
systemOduRxLO OBJECT-TYPE
SYNTAX Integer32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Combes Expires January 9, 2008 [Page 10]
Internet-Draft DVB-RCS MIB July 2007
" Frequency of LNB Local Oscillator (in 100 Hz)"
::= {rcstSystem 10}
systemOduTxLO OBJECT-TYPE
SYNTAX Integer32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of BUC Local Oscillator (in 100 Hz) "
::= {rcstSystem 11}
===================================================================
-- rcstInstall sub-tree object types
===================================================================
installAntennaAlignmentState OBJECT-TYPE
SYNTAX INTEGER {
antennaAlignmentStart (1),
antennaAlignmentDeny (2),
antennaAlignmentContinue (3),
antennaAlignmentStop (4),
antennaAlignmentSuccess (5),
antennaAlignmentFail (6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" Indicates the state:
(1)-Start;
(2)-Deny;
(3)-Continue;
(4)-Stop;
(5)-Success;
(6)-Fail"
::= {rcstInstall 1}
installCwFrequency OBJECT-TYPE
SYNTAX Integer32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
Combes Expires January 9, 2008 [Page 11]
Internet-Draft DVB-RCS MIB July 2007
DESCRIPTION
"Frequency at which the carrier is put up (in 100 Hz).
Minimum required precision is 1 kHz."
::= {rcstInstall 2}
installCwMaxDuration OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time after which the carrier must be put down (in seconds)"
::= {rcstInstall 3}
installCwPower OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specified in tenth of dBm. This parameter allows for fine
(manual) tuning of the power setup. Minimum required precision
is 1 dBm. It must be configurable while CW signal is on. Once
the power has been properly adjusted, the power setup is stored
in rtnConfigDefIfLevel."
::= {rcstInstall 4}
installCoPolReading OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Co-Pol measured value (in 0.1 dB)"
::= {rcstInstall 5}
installXPolReading OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Cross-Pol measured value (in 0.1 dB)"
::= {rcstInstall 6}
Combes Expires January 9, 2008 [Page 12]
Internet-Draft DVB-RCS MIB July 2007
installCoPolTarget OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Co-Pol target (in 0.1 dB) "
::= {rcstInstall 7}
installXPolTarget OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Cross-Pol target (in 0.1 dB)"
::= {rcstInstall 8}
installStandByDurationOBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time to wait in stand-by mode (in seconds)"
::= {rcstInstall 9}
installTargetEsNoOBJECT-TYPE
SYNTAX Integer32(0..315)
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This value describes the wanted Es/N0 value that enables
operation of the return link with the required error
performance. The values shall be given in tenth of dB and
the initial value shall be equal to 7 dB. The range shall be
from 0 dBm to 31.5 dBm with a precision of 0.1 dB."
DEFVAL { 70 }
::= {rcstInstall 10}
===================================================================
Combes Expires January 9, 2008 [Page 13]
Internet-Draft DVB-RCS MIB July 2007
-- rcstNetwork sub-tree object types
===================================================================
networkOamIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"OAM IP Address of the RCST. This object used with both ip and
interfaces MIB-II subgroups determines uniquely the interface
through which OAM traffic is passing through.
Note that the OAM IP address may be statically or dynamically
assigned. It is system dependent whether the OAM IP address
and the Traffic IP address are the same address."
::= {rcstNetwork 1}
networkOamIpNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Network Mask for the OAM IP Address."
::= {rcstNetwork 2}
networkOamIpAddrAssign OBJECT-TYPE
SYNTAX INTEGER {
oamIpAddressStatic (1),
oamIpAddressDynamic (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Identifies whether the OAM IP address is statically
('static' - 1) or dynamically ('dynamic' - 2) assigned."
::= {rcstNetwork 3}
networkLanIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the LAN interface"
::= {rcstNetwork 4}
networkLanIpMask OBJECT-TYPE
Combes Expires January 9, 2008 [Page 14]
Internet-Draft DVB-RCS MIB July 2007
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Mask for the LAN interface"
::= {rcstNetwork 5}
networkAirInterfaceDefaultGateway OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Default Gateway for the air interface"
::= {rcstNetwork 6}
networkDnsServerIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the DNS server in the NCC."
::= {rcstNetwork 7}
networkNccMgtIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the management server in the NCC."
::= {rcstNetwork 8}
networkConfigFileDownloadUrl OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path name for the configuration file download.
It includes the protocol type (tftp or ftp) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST."
::= {rcstNetwork 9}
networkInstallLogFileDownloadUrl OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Combes Expires January 9, 2008 [Page 15]
Internet-Draft DVB-RCS MIB July 2007
"Full path of the installation log file to download.
It includes the protocol type (tftp or ftp) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST. The installation
log file can be created on the installer's computer
and downloaded to the RCST."
::= {rcstNetwork 10}
networkConfigFileUploadUrl OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path name for the configuration file upload.
It includes the protocol type (tftp or ftp) and the
associated server IP address or hostname.Hostname can
only be used if DNS is supported by the RCST."
::= {rcstNetwork 11}
networkLogFileUploadUrl OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the event log file. It includes the protocol
type (tftp or ftp) and the associated server IP address
or hostname. Hostname can only be used if DNS is supported
by the RCST."
::= {rcstNetwork 12}
networkInstallLogFileUploadUrl OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the installation log file. It includes the
protocol type (tftp or ftp) and the associated server
IP address or hostname. Hostname can only be used if DNS is
supported by the RCST. The installation log file can be
retrieved from the RCST by the NCC or by the installer
via the LAN."
::= {rcstNetwork 13}
===================================================================
-- rtnConfig sub-tree object types
===================================================================
Combes Expires January 9, 2008 [Page 16]
Internet-Draft DVB-RCS MIB July 2007
rtnconfigMaxEirp OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum allowed EIRP in tenth of dBm on the return link."
::= {rtnConfig 1}
rtnconfigDefIfLevel OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Default transmitted IF power level, specified in tenth of dBm,
out of the IDU for sending a CSC burst at RCST reboot or
power on. Applies to all signals transmitted by RCST
(CW and traffic) immediately."
::= {rtnConfig 2}
===================================================================
-- rtnStatus sub-tree object types
===================================================================
rtnstatusEbN0 OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The EbN0 value reported for the return link, referenced to the
regular SYNC burst transmission."
::= {rtnStatus 1}
rtnstatusSFduration OBJECT-TYPE
SYNTAX Integer32 (250..7500)
UNITS "0.1 ms"
MAX-ACCESS read-only
Combes Expires January 9, 2008 [Page 17]
Internet-Draft DVB-RCS MIB July 2007
STATUS current
DESCRIPTION
"The duration of the currently applied return link super-frame
structure, in tenths of milliseconds."
::= {rtnStatus 2}
rtnstatusPayloadUnit OBJECT-TYPE
SYNTAX INTEGER {
unitATM (0),
unitMPEG (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if the payload unit used for the return link is ATM
or MPEG."
::= {rtnStatus 3}
===================================================================
-- fwdConfig sub-tree object types
===================================================================
fwdStartTable OBJECT-TYPE
SYNTAX SEQUENCE OF FwdStartEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Lists Forward Links attachment points (e.g. different for
installation and operation). The table describes the forward link
parameters used for the start-up stream with the NCC."
::={fwdConfig 1}
fwdStartEntry OBJECT-TYPE
SYNTAX FwdStartEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Forward Link StartConfig table."
INDEX { fwdStartIndex, fwdStartPopId }
Combes Expires January 9, 2008 [Page 18]
Internet-Draft DVB-RCS MIB July 2007
::= { fwdStartTable 1 }
FwdStartEntry ::= SEQUENCE {
fwdStartIndex Integer32,
fwdStartPopId Integer32,
fwdStartFrequency Integer32,
fwdStartPolar INTEGER,
fwdStartFormat INTEGER,
fwdStartRolloff INTEGER,
fwdStartSymbolRate Integer32,
fwdStartInnerFec INTEGER,
fwdStartRowStatus RowStatus
}
fwdStartIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Table index."
::={fwdStartEntry 1}
fwdStartPopId OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Population identifier associated with the start-up
forward link:
-1: any (auto)
0-65535: specific StartPopId
If 'any' is set, the RCST will assume membership of any annonced
population ID and will
commence with logon in accordance with this assumption."
::={fwdStartEntry 2}
fwdStartFrequency OBJECT-TYPE
SYNTAX Integer32
UNITS "100 kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Frequency of the start transponder carrying a
Combes Expires January 9, 2008 [Page 19]
Internet-Draft DVB-RCS MIB July 2007
Network Information Table to which any RCST shall
trigger to acquire forward link. ts value shall be given
in multiple of 100 kHz."
::={fwdStartEntry 3}
fwdStartPolar OBJECT-TYPE
SYNTAX INTEGER {
linearHorizontal (0),
linearVertical (1),
circularLeft (2),
circularRight (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"2-bit field giving the polarization of the start transponder
carrying an Network Information Table to which any RCST shall
trigger to acquire forward link:
00: linear and horizontal
01: linear and vertical
10: circular left
11: circular right"
::={fwdStartEntry 4}
fwdStartFormat OBJECT-TYPE
SYNTAX INTEGER {
auto (-1),
dvbs (0),
dvbs2 (1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the transmission format standard applied for the
start
transport stream. The start transport stream carries a
Network Information Table that the RCST uses for acquiring
the forward link signaling. Supported values are:
-1: unspecified (automatic format acquisition is assumed)
0: DVB-S (mandatory if DVBS support is claimed)
1: DVB-S2 CCM (mandatory if CCM support is claimed)
2: DVB-S2 ACM (mandatory if ACM support is claimed)
This allows the RCST to discriminate between CCM and ACM when
selecting FL.
Combes Expires January 9, 2008 [Page 20]
Internet-Draft DVB-RCS MIB July 2007
The support of automatic format selection is optional. One or
several of the other
format selections must be supported, according to the claimed
SatLabs profile support."
::={fwdStartEntry 5}
fwdStartRolloff OBJECT-TYPE
SYNTAX INTEGER {
autoRolloff (0),
rolloff020 (1),
rolloff025 (2),
rolloff035 (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the roll-off applied on the start transponder.
The start transponder carries a Network Information Table
that the RCST uses for acquiring the forward link signaling.
Supported values are:
0: any (auto)
1: 0.20
2: 0.25
3: 0.35
4-n: reserved"
::={fwdStartEntry 6}
fwdStartSymbolRate OBJECT-TYPE
SYNTAX Integer32
UNITS "100 symbols/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the symbol rate on the start transponder
carrying a Network Information Table to which any RCST
shall trigger to acquire forward link. Its value shall be
given in multiple of 100 symbols/s."
::={fwdStartEntry 7}
fwdStartInnerFec OBJECT-TYPE
SYNTAX INTEGER {
autoFec (-1),
fecRate1/2 (0),
Combes Expires January 9, 2008 [Page 21]
Internet-Draft DVB-RCS MIB July 2007
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (12),
fecRate1/3 (13),
fecRate1/4 (14),
noInnerCode (15) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the inner Forward Error Correction used on the
start transponder carrying a NIT to which any RCST shall
trigger to acquire forward link.
Supported values are:
autoFec (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (12),
fecRate1/3 (13),
fecRate1/4 (14),
noInnerCode (15)
The support of autoFec is optional."
::={fwdStartEntry 8}
fwdStartRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Standard SNMP row status"
DEFVAL { active }
Combes Expires January 9, 2008 [Page 22]
Internet-Draft DVB-RCS MIB July 2007
::={fwdStartEntry 9}
===================================================================
-- fwdStatus sub-tree object types
===================================================================
fwdStatusPopId OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Population identifier applied at log-on:
0-65535: specific StartPopId
If the RCST was allowed to logon any population, the RCST will
report the base number of the announced
population ID indicated by the RMT linkage descriptor used at
logon."
::={fwdStatus 1}
fwdStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF FwdStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the current status of Forward Link
interfaces."
::={fwdStatus 2}
fwdStatusEntry OBJECT-TYPE
SYNTAX FwdStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Forward Link Status table. Each entry is
associated with a physical interface. A RCST SHALL support at least
one entry."
INDEX { fwdStatusIndex, fwdStatusIfReference }
::= { fwdStatusTable 1 }
FwdStatusEntry ::= SEQUENCE {
fwdStatusIndex Integer32,
fwdStatusIfReference Integer32,
Combes Expires January 9, 2008 [Page 23]
Internet-Draft DVB-RCS MIB July 2007
fwdStatusNetId Integer32,
fwdStatusNetName DisplayString,
fwdStatusFormat INTEGER,
fwdStatusFrequency Integer32,
fwdStatusPolar INTEGER,
fwdStatusInnerFec INTEGER,
fwdStatusSymbolRate Integer32,
fwdStatusRolloff INTEGER,
fwdStatusModulation INTEGER,
fwdStatusFecFrame INTEGER,
fwdStatusPilot INTEGER,
fwdStatusBer Integer32,
fwdStatusCnr Integer32,
fwdStatusRxPower Integer32,
fwdStatusRowStatus RowStatus
}
fwdStatusIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Table index."
::={fwdStatusEntry 1}
fwdStatusIfReference OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cross reference to the interface table"
::={fwdStatusEntry 2}
fwdStatusNetId OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interactive network identifier of the forward
link (from RMT)"
::={fwdStatusEntry 3}
fwdStatusNetName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Combes Expires January 9, 2008 [Page 24]
Internet-Draft DVB-RCS MIB July 2007
"The name of the interactive network of the forward
link (from RMT)"
::={fwdStatusEntry 4}
fwdStatusFormat OBJECT-TYPE
SYNTAX INTEGER {
dvbs (0),
dvbs2ccm (1),
dvbs2acm (2),
reservedFormat (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the transmission format applied on the forward link.
Supported values are (from RMT):
0: DVB-S
1: DVB-S2 using CCM
2: DVB-S2 using ACM
3: reserved"
::={fwdStatusEntry 5}
fwdStatusFrequency OBJECT-TYPE
SYNTAX Integer32
UNITS "100 kHz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the frequency of the forward link. Its value
shall
be given in multiple of 100 kHz."
::={fwdStatusEntry 6}
fwdStatusPolar OBJECT-TYPE
SYNTAX INTEGER {
linearHorizontal (0),
linearVertical (1),
circularLeft (2),
circularRight (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"2-bit field giving the polarization of the forward link
(from RMT):
00: linear and horizontal
Combes Expires January 9, 2008 [Page 25]
Internet-Draft DVB-RCS MIB July 2007
01: linear and vertical
10: circular left
11: circular right"
::={fwdStatusEntry 7}
fwdStatusInnerFec OBJECT-TYPE
SYNTAX INTEGER {
unknown (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (12),
fecRate1/3 (13),
fecRate1/4 (14),
noInnerCode (15) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the inner Forward Error Correction used on the
forward link for transmission to the RCST.
Supported values are:
unknown (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (12),
fecRate1/3 (13),
fecRate1/4 (14),
noInnerCode (15)
The RCST will report a value that has been used for transmission
to the RCST within the most recent 60 seconds.
If this is not relevant, the RCST will report 'unkown'."
Combes Expires January 9, 2008 [Page 26]
Internet-Draft DVB-RCS MIB July 2007
::={fwdStatusEntry 8}
fwdStatusSymbolRate OBJECT-TYPE
SYNTAX Integer32
UNITS "100 symbols/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the symbol rate of the forward link.
Its value shall be given in multiple of 100 symbol/s."
::={fwdStatusEntry 9}
fwdStatusRolloff OBJECT-TYPE
SYNTAX INTEGER {
undefRolloff (0),
r020 (1),
r025 (2),
r035 (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the roll-off applied on the forward link.
Supported values are:
0: undefined
1: 0.20
2: 0.25
3: 0.35
4-15: reserved"
::={fwdStatusEntry 10}
fwdStatusModulation OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
mBPSK (1),
mQPSK (2),
m8PSK (3),
m16APSK (4),
m32APSK (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Combes Expires January 9, 2008 [Page 27]
Internet-Draft DVB-RCS MIB July 2007
"Indicates the modulation on the forward link used for
transmission to the RCST.
0: unknown
1: BPSK
2: QPSK
3: 8PSK
4: 16APSK
5: 32APSK
The RCST will report a value that has been used for transmission
to the RCST within the most recent 60 seconds.
If this is not relevant, the RCST will report 'unkown'."
::={fwdStatusEntry 11}
fwdStatusFecFrame OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
shortframe (1),
longframe (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the frame length used on the forward link for
transmission to the RCST.
Supported values are:
0: Unknown
1: Normal frame
2: Short frame
The RCST will report a value that has been used for transmission
to the RCST within the most recent 60 seconds.
If this is not relevant, the RCST will report 'unkown'."
::={fwdStatusEntry 12}
fwdStatusPilot OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
pilotNotused(1),
pilotUsed (2)
Combes Expires January 9, 2008 [Page 28]
Internet-Draft DVB-RCS MIB July 2007
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether pilots are used on the forward link for
transmission to the RCST.
Supported values are:
0: Unknown
1: Pilots are not used
2: Pilot not used
The RCST will report a value that has been used for transmission
to the RCST within the most recent 60 seconds.
If this is not relevant, the RCST will report 'unkown'."
::={fwdStatusEntry 13}
fwdStatusBer OBJECT-TYPE
SYNTAX Integer32
UNITS "exponent of 10"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the RCST BER on the Forward Link in log10 units."
::={fwdStatusEntry 14}
fwdStatusCnr OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the RCST CNR on the Forward Link in 0.1 dB units."
::={fwdStatusEntry 15}
fwdStatusRxPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the power level of the Forward Link as received at the
IDU, in 0.1 dBm units."
DEFVAL { -500 }
::={fwdStatusEntry 16}
Combes Expires January 9, 2008 [Page 29]
Internet-Draft DVB-RCS MIB July 2007
fwdStatusRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Standard SNMP row status"
DEFVAL { active }
::={fwdStatusEntry 17}
===================================================================
-- rcstQos sub-tree object types
===================================================================
pktClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF PktClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the packet classification used in the
DVB-RCS terminal. The number of entries is specified by
PktClassIndex. "
::={rcstQos 1}
pktClassEntry OBJECT-TYPE
SYNTAX PktClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the packet classification table. One object type
of each entry may have a value in the active range
(a non-default value).The other object types are then assumed set
to 'inactive'. The entry with the lowest index
value takes precedence when classifying a packet."
INDEX { pktClassIndex }
::= { pktClassTable 1 }
PktClassEntry ::= SEQUENCE {
pktClassIndex INTEGER,
pktClassDscpLow Integer32,
pktClassDscpHigh Integer32,
pktClassDscpMarkValue Integer32,
pktClassIPProtocol Integer32,
pktClassIPSrcAddr IpAddress,
pktClassIPSrcAddrMask IpAddress,
Combes Expires January 9, 2008 [Page 30]
Internet-Draft DVB-RCS MIB July 2007
pktClassIPDstAddr IpAddress,
pktClassIPDstAddrMask IpAddress,
pktClassSrcPortLow Integer32,
pktClassSrcPortHigh Integer32,
pktClassDstPortLow Integer32,
pktClassDstPortHigh Integer32,
pktClassVlanUserPri Integer32,
pktClassPhbAssociation Integer32,
pktClassRowStatus RowStatus
}
pktClassIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index automatically incremented by one at row creation."
::={pktClassEntry 1}
pktClassDscpLow OBJECT-TYPE
SYNTAX Integer32 (0..63)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low value of a range
of DSCP values to which a packet is compared. A value of 0
is used to inactivate."
DEFVAL { 0 }
::={pktClassEntry 2}
pktClassDscpHigh OBJECT-TYPE
SYNTAX Integer32 (0..63)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high value of a range of
DSCP values to which a packet is compared. A value of 63 is
used to inactivate."
DEFVAL { 63 }
::={pktClassEntry 3}
pktClassDscpMarkValue OBJECT-TYPE
SYNTAX Integer32 (-1..63)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Combes Expires January 9, 2008 [Page 31]
Internet-Draft DVB-RCS MIB July 2007
"This object is the DSCP value used to mark the packet,
64 indicates no DSCP marking, possible DSCP marks values
are (0..63)"
DEFVAL { -1 }
::={pktClassEntry 4}
pktClassIPProtocol OBJECT-TYPE
SYNTAX Integer32 (-1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP protocol to which a
packet is compared. A value of 255 indicates inactive."
DEFVAL { -1 }
::={pktClassEntry 5}
pktClassIPSrcAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP source address to which a
packet is compared."
::={pktClassEntry 6}
pktClassIPSrcAddrMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies which bits of the IP source
address will be matched. A mask of all zeros inidcates that
the selectivity is inactive."
DEFVAL { 0 }
::={pktClassEntry 7}
pktClassIPDstAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP destination address to which a
packet is compared."
::={pktClassEntry 8}
pktClassIPDstAddrMask OBJECT-TYPE
Combes Expires January 9, 2008 [Page 32]
Internet-Draft DVB-RCS MIB July 2007
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies which bits of the IP destination
address will be matched. A mask of all zeros indicates that
the selectivity is inactive."
DEFVAL { 0 }
::={pktClassEntry 9}
pktClassSrcPortLow OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low range of the source
port to which a packet is compared. A value of -1 indicates
that the selectivity is inactive."
DEFVAL { -1 }
::={pktClassEntry 10}
pktClassSrcPortHigh OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high range of the source
port to which a packet is compared. A value of -1 indicates
that the selectivity is inactive."
DEFVAL { -1 }
::={pktClassEntry 11}
pktClassDstPortLow OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low range of the destination
port to which a packet is compared. A value of -1 indicates
that the selectivity is inactive."
DEFVAL { -1 }
::={pktClassEntry 12}
pktClassDstPortHigh OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-create
STATUS current
Combes Expires January 9, 2008 [Page 33]
Internet-Draft DVB-RCS MIB July 2007
DESCRIPTION
"This object specifies the high range of the destination
port to which a packet is compared. A value of -1 indicates
that the selectivity is inactive."
DEFVAL { -1 }
::={pktClassEntry 13}
pktClassVlanUserPri OBJECT-TYPE
SYNTAX Integer32 (-1..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the VLAN User Priority
to which a packet is compared. A value of -1 indicates that
the selectivity is inactive."
DEFVAL { -1 }
::={pktClassEntry 14}
pktClassPhbAssociation OBJECT-TYPE
SYNTAX Integer32 (0..63)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Associate the filter entry to a specific PHB (refer to
phbIdentifier)."
::={pktClassEntry 15}
pktClassRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Standard SNMP row status"
::={pktClassEntry 16}
===================================================================
-- PhbMappingTable
===================================================================
phbMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhbMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a list of PHB MIB entries. It describes the
PHB mapping to the Request Class."
::={rcstQos 2}
Combes Expires January 9, 2008 [Page 34]
Internet-Draft DVB-RCS MIB July 2007
phbMappingEntry OBJECT-TYPE
SYNTAX PhbMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the PHB mapping table."
INDEX { phbIdentifier }
::= { phbMappingTable 1 }
PhbMappingEntry ::= SEQUENCE {
phbIdentifier Integer32,
phbName DisplayString,
phbRequestClassAssociation Integer32,
phbMappingRowStatus RowStatus
}
phbIdentifier OBJECT-TYPE
SYNTAX Integer32 (0..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identification of the PHB (0..63)."
::={phbMappingEntry 1}
phbName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name of the PHB."
::={phbMappingEntry 2}
phbRequestClassAssociation OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is an association of this PHB
to a Request class (by reference to a Request Class index)."
::={phbMappingEntry 3}
phbMappingRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Combes Expires January 9, 2008 [Page 35]
Internet-Draft DVB-RCS MIB July 2007
"Standard SNMP row status"
DEFVAL { active }
::={phbMappingEntry 4}
===================================================================
-- RequestClassTable
===================================================================
requestClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF RequestClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a list of Request class entries. This class
describes the layer 2 QoS objects."
::={rcstQos 3}
requestClassEntry OBJECT-TYPE
SYNTAX RequestClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Request class table."
INDEX { requestClassIndex }
::= { requestClassTable 1 }
RequestClassEntry ::= SEQUENCE {
requestClassIndex Integer32,
requestClassName DisplayString,
requestClassChanId Integer32,
requestClassVccVpi Integer32,
requestClassVccVci Integer32,
requestClassPidPoolReference Integer32,
requestClassCra INTEGER,
requestClassRbdcMax INTEGER,
requestClassRbdcTimeout INTEGER,
requestClassVbdcMax INTEGER,
requestClassVbdcTimeout INTEGER,
requestClassVbdcMaxBackLog INTEGER,
requestClassAvbdcRepTime INTEGER,
requestClassRowStatus RowStatus
}
requestClassIndex OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-only
Combes Expires January 9, 2008 [Page 36]
Internet-Draft DVB-RCS MIB July 2007
STATUS current
DESCRIPTION
"Index of the Request Class table. A total of 16 entries is
supported."
::={requestClassEntry 1}
requestClassName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Name of the Request class."
::={requestClassEntry 2}
requestClassChanId OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Channel id of the Request class."
::={requestClassEntry 3}
requestClassVccVpi OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Defines VPI used for the Request class (ATM profile)."
::={requestClassEntry 4}
requestClassVccVci OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Defines VCI used for the Request class (ATM profile)."
::={requestClassEntry 5}
requestClassPidPoolReference OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Reference to the PID pool applicable for the request class."
::={requestClassEntry 6}
requestClassCra OBJECT-TYPE
Combes Expires January 9, 2008 [Page 37]
Internet-Draft DVB-RCS MIB July 2007
SYNTAX INTEGER
UNITS "bits/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Define CRA level for the Request class in bit per second
(b/s)."
::={requestClassEntry 7}
requestClassRbdcMax OBJECT-TYPE
SYNTAX INTEGER
UNITS "2 kbits/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" Max RBDC that can be requested for the Request class, in
number of 2 Kb/s"
::={requestClassEntry 8}
requestClassRbdcTimeout OBJECT-TYPE
SYNTAX INTEGER
UNITS "superframes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Persistence of the RBDC request, expressed in superframes"
::={requestClassEntry 9}
requestClassVbdcMax OBJECT-TYPE
SYNTAX INTEGER
UNITS "ATM cells/MPEG packets"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Max VBDC that can be requested for the Request class,
in payload units (one ATM cell or one MPEG packet) per
superframe"
::={requestClassEntry 10}
requestClassVbdcTimeout OBJECT-TYPE
SYNTAX INTEGER
UNITS "superframes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time after which the RCST considers that the pending requests
are lost.
Combes Expires January 9, 2008 [Page 38]
Internet-Draft DVB-RCS MIB July 2007
The RCST may issue new request for that traffic. VBDC Timeout is
expressed in superframes."
::={requestClassEntry 11}
requestClassVbdcMaxBackLog OBJECT-TYPE
SYNTAX INTEGER
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"VBDC back Log per Request class. (expressed in bytes)"
::={requestClassEntry 12}
requestClassAvbdcRepTime OBJECT-TYPE
SYNTAX INTEGER
UNITS "superframes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Optional parameter. AVBDC requests can be sent periodically,
according to the value of that parameter.
AVBDCRepTime is expressed in superframes."
::={requestClassEntry 13}
requestClassRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Standard SNMP row status"
DEFVAL { active }
::={requestClassEntry 14}
===================================================================
-- the table of PID pools
===================================================================
pidPoolTable OBJECT-TYPE
SYNTAX SEQUENCE OF PidPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the PID pools. A PID value may occur in
more than one PID pool. Each PID value can effectively
Combes Expires January 9, 2008 [Page 39]
Internet-Draft DVB-RCS MIB July 2007
occur only once in each pool. Only one Pid per PID pool is
required for short term QoS support."
::={rcstQos 4}
pidPoolEntry OBJECT-TYPE
SYNTAX PidPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the PID list table."
INDEX { pidPoolIndex, pidIndex }
::= { pidPoolTable 1 }
PidPoolEntry ::= SEQUENCE {
pidPoolIndex Integer32,
pidIndex Integer32,
pidValue Integer32,
pidPoolRowStatus RowStatus
}
pidPoolIndex OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index of the Pid pool in the PID pool table."
::={pidPoolEntry 1}
pidIndex OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index of the PID entry within the PID pool."
::={pidPoolEntry 2}
pidValue OBJECT-TYPE
SYNTAX Integer32 (0..8191)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Define one of the PIDs to be used in a PID pool of
pidPoolIndex."
::={pidPoolEntry 3}
pidPoolRowStatus OBJECT-TYPE
SYNTAX RowStatus
Combes Expires January 9, 2008 [Page 40]
Internet-Draft DVB-RCS MIB July 2007
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Standard SNMP row status"
DEFVAL { active }
::={pidPoolEntry 4}
qosGlobalRbdcMax OBJECT-TYPE
SYNTAX INTEGER
UNITS "2 kbits/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The global RBDC max is for information only and it is
optional.
(expressed in number of 2 kb/s)"
::={rcstQos 5}
qosGlobalVbdcMax OBJECT-TYPE
SYNTAX INTEGER
UNITS "ATM cells/MPEG packets"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The global VBDC max is for information only and it is
optional.(expressed in payload units/superframe)"
::={rcstQos 6}
qosGlobalVbdcMaxBackLog OBJECT-TYPE
SYNTAX INTEGER
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The global VBDC back log is used only if the VBDC back log
is not
configured in the Request class. (expressed in bytes)"
::={rcstQos 7}
qosGlobalAvbdcRepTime OBJECT-TYPE
SYNTAX INTEGER
UNITS "superframes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The global AVBDC rep time is optional (expressed in
superframes)."
Combes Expires January 9, 2008 [Page 41]
Internet-Draft DVB-RCS MIB July 2007
::={rcstQos 8}
qosChannelIdStrictDispatching OBJECT-TYPE
SYNTAX INTEGER {
not_strict (0),
strict (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the RCST will strictly follow RC
association when
signaled through Channel_ID in the TBTP:
No strict association (0)
Strict association (1)"
::={rcstQos 9}
===================================================================
-- rcstState sub-tree object types
===================================================================
rcstMode OBJECT-TYPE
SYNTAX INTEGER {
installation (0),
operational (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allows to identify in which mode the RCST is and to return it
to the installation mode when needed. Values for the RCST mode are:
Installation (0)
Operational (1)"
::={rcstState 1}
rcstFaultStatus OBJECT-TYPE
SYNTAX INTEGER {
nofault (0),
fault (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provide the fault status of the terminal. The fault status
management is vendor specific. Values for the Fault Status are:
no fault (0)
Combes Expires January 9, 2008 [Page 42]
Internet-Draft DVB-RCS MIB July 2007
fault (1)"
::={rcstState 2}
rcstFwdLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
notAcquired (0),
acquired (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the status of the RCST Forward Link. Values for the
Forward Link Status are:
Not acquired (0)
Acquired (1)"
::={rcstState 3}
rcstRtnLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
loggedOff (0),
loggedOn (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the status of the RCST Return Link. Values for the
Return Link Status are:
Logged-off (0)
Logged-on (1)"
::={rcstState 4}
rcstLogUpdated OBJECT-TYPE
SYNTAX INTEGER {
noUpdate (0),
logfileUpdated (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the existence of an updated log file:
No update (0)
Log file updated (1)
The RCST should remove the Log file updated indication
as the log file is fetched by the NCC."
::={rcstState 5}
rcstCurrentSoftwareVersion OBJECT-TYPE
Combes Expires January 9, 2008 [Page 43]
Internet-Draft DVB-RCS MIB July 2007
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current RCST software version."
::={rcstState 6}
rcstAlternateSoftwareVersion OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Alternate (backup/new) RCST software version."
::={rcstState 7}
rcstActivatedConfigFileVersion OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the most recently activated configuration file.
Version is vendor specific."
::={rcstState 8}
rcstDownloadedConfigFileVersion
OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the most recently downloaded configuration file.
Version is vendor specific. If the
value is different from rcstActivatedConfigFileVersion, it is
pending for activation."
::={rcstState 9}
===================================================================
-- rcstControl sub-tree object types
====================================================================
ctrlRebootCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
normal (2),
alternate (3)
}
MAX-ACCESS read-write
Combes Expires January 9, 2008 [Page 44]
Internet-Draft DVB-RCS MIB July 2007
STATUS current
DESCRIPTION
"This variable shall force the RCST to reboot
(1)- idle
(2)- normal reboot (from current software load)
(3)- reboot from alternate load (swap to alternate load
before reboot)"
DEFVAL {1}
::={rcstControl 1}
ctrlRcstTxDisableOBJECT-TYPE
SYNTAX INTEGER {
idle (1),
disable (2),
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall force the RCST to stop transmission
(transmit disabled as defined in [1]):
(1)- idle
(2)- initiate Tx Disabled"
DEFVAL {1}
::={rcstControl 2}
ctrlUserTrafficDisableOBJECT-TYPE
SYNTAX INTEGER {
idle (1),
disable (2),
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall disable user traffic (only RCST
management traffic can be transmitted)
(1)- idle
(2)- disable user traffic"
DEFVAL {1}
::={rcstControl 3}
ctrlCwEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2),
Combes Expires January 9, 2008 [Page 45]
Internet-Draft DVB-RCS MIB July 2007
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will force the RCST to start transmission of CW,
if the RCST is first set to the installation state, and is properly
configured for CW transmission:
(1)- off
(2)- on"
DEFVAL {1}
::={rcstControl 4}
ctrlOduTxReferenceEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2),
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of 10 MHz reference
clock in the Tx IFL cable:
(1) off
(2) on"
DEFVAL {2}
::={rcstControl 5}
ctrlOduTxDCEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2),
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of DC in the Tx IFL
cable:
(1) off
(2) on"
DEFVAL {2}
::={rcstControl 6}
ctrlOduRxDCEnable OBJECT-TYPE
Combes Expires January 9, 2008 [Page 46]
Internet-Draft DVB-RCS MIB July 2007
SYNTAX INTEGER {
off (1),
on (2),
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of DC in the Rx IFL
cable:
(1) off
(2) on"
DEFVAL {2}
::={rcstControl 7}
ctrlDownloadFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
config (2),
installationLog (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall initiate a RCST configuration file download
process
(1) idle
(2) download RCST configuration file from TFTP/FTP server
(3) download RCST installation log file from TFTP/FTP server
(INSTALL_LOG OPTION)"
DEFVAL {1}
::={rcstControl 8}
ctrlUploadFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
config (2),
eventAlarm (3),
installationLog (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall initiate a RCST upload process
(1) idle
Combes Expires January 9, 2008 [Page 47]
Internet-Draft DVB-RCS MIB July 2007
(2) upload RCST configuration file to TFTP/FTP server
(3) upload RCST event/alarm log file to TFTP/FTP server
(4) upload RCST installation log file to TFTP/FTP server
(INSTALL_LOG OPTION)"
DEFVAL {1}
::={rcstControl 9}
ctrlActivateConfigFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
activate (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Triggers the RCST to use the configuration file and update
its parameters accordingly. Some RCST implementation may
require
a reboot for the parameters to take effect (vendor specific).
(1) Idle
(2) activate"
DEFVAL {1}
::={rcstControl 10}
ctrlRcstLogonCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
logon (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall initiate a RCST logon
(1) idle
(2) initiate RCST logon"
DEFVAL {1}
::={rcstControl 11}
ctrlRcstLogoffCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
logoff (2)
}
MAX-ACCESS read-write
Combes Expires January 9, 2008 [Page 48]
Internet-Draft DVB-RCS MIB July 2007
STATUS current
DESCRIPTION
"This variable shall initiate a RCST logoff
(1) idle
(2) initiate RCST logoff"
DEFVAL {1}
::={rcstControl 12}
===================================================================
-- conformance information
====================================================================
rcstGroups OBJECT IDENTIFIER ::= {dvbrcsConformance 1}
rcstCompliances OBJECT IDENTIFIER ::= {dvbrcsConformance 2}
===================================================================
-- conformance statements
===================================================================
rcstCompliance1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for DVB-RCS
terminals that are compliant with SatLabs system
recommendations version 2."
MODULE -- this module
MANDATORY-GROUPS {rcstSystemGroup, rcstInstallGroup,
rcstNetworkGroup, rtnConfigGroup, fwdConfigGroup, fwdStatusGroup,
rcstQosGroup, rcstStateGroup, rcstControlGroup}
GROUP rcstExtSystemGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the SNMPALL option."
GROUP rcstExtNetworkGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the SNMPALL option."
Combes Expires January 9, 2008 [Page 49]
Internet-Draft DVB-RCS MIB July 2007
GROUP rcstExtInstallGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the INSTALL_LOG option."
GROUP rcstDnsGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the DNS option."
GROUP rtnExtConfigGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the SNMPALL option."
GROUP fwdExtStatusGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the FWDLINKSTATUS option."
GROUP rcstEnhancedClassifierGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the ENHCLASSIFIER option."
GROUP rcstMpegQosGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the MPEG option."
GROUP rcstAvbdcRepQosGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the AVBDC_REP option."
GROUP rcstGlobalQosGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the RCST_PARA option."
Combes Expires January 9, 2008 [Page 50]
Internet-Draft DVB-RCS MIB July 2007
GROUP rcstGlobalAvbdcRepQosGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support both the RCST_PARA option and the
AVBDC_REP option."
GROUP rcstStrictQosGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the CHID_STRICT option."
GROUP rtnStatusGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the SNMPALL option."
GROUP rcstExtControlGroup
DESCRIPTION "This group is mandatory for an RCST that
claims to support the SNMPALL option."
OBJECT systemOduTxType
MIN-ACCESS read-only
DESCRIPTION "Write access required if the RCST
doesn't provide the information."
OBJECT systemOduRxType
MIN-ACCESS read-only
DESCRIPTION "Write access required if the RCST
doesn't provide the information."
OBJECT networkLanIpAddress
MIN-ACCESS read-only
Combes Expires January 9, 2008 [Page 51]
Internet-Draft DVB-RCS MIB July 2007
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT networkLanIpMask
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT pktClassDscpLow
MIN-ACCESS read-only
DESCRIPTION "Create access only required if
ENHCLASSIFIER support is claimed."
OBJECT pktClassDscpHigh
MIN-ACCESS read-only
DESCRIPTION "Create access only required if
ENHCLASSIFIER support is claimed."
OBJECT pktClassDscpMarkValue
MIN-ACCESS read-only
DESCRIPTION "Create access only required if
ENHCLASSIFIER support is claimed."
OBJECT phbIdentifier
MIN-ACCESS read-only
DESCRIPTION "Create access only required if SNMPALL
support is claimed."
OBJECT phbName
Combes Expires January 9, 2008 [Page 52]
Internet-Draft DVB-RCS MIB July 2007
MIN-ACCESS read-only
DESCRIPTION "Create access only required if SNMPALL
support is claimed."
OBJECT phbRequestClassAssociation
MIN-ACCESS read-only
DESCRIPTION "Create access only required if SNMPALL
support is claimed."
OBJECT phbMappingRowStatus
MIN-ACCESS read-only
DESCRIPTION "Create access only required if SNMPALL
support is claimed."
OBJECT requestClassName
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassChanId
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassVccVpi
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassVccVci
Combes Expires January 9, 2008 [Page 53]
Internet-Draft DVB-RCS MIB July 2007
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassPidPoolReference
MIN-ACCESS not-accessible
DESCRIPTION "Read-only access required if MPEG option
is claimed. Write access
only required if also SNMPALL support is claimed."
OBJECT requestClassCra
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassRbdcMax
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassRbdcTimeout
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassVbdcMax
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
Combes Expires January 9, 2008 [Page 54]
Internet-Draft DVB-RCS MIB July 2007
OBJECT requestClassVbdcTimeout
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassVbdcMaxBacklog
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT requestClassRowStatus
MIN-ACCESS read-only
DESCRIPTION "Write access only required if SNMPALL
support is claimed."
OBJECT pidPoolIndex
MIN-ACCESS not-accessible
DESCRIPTION "Read-only access required if MPEG option
is claimed."
OBJECT pidIndex
MIN-ACCESS not-accessible
DESCRIPTION "Read-only access required if MPEG option
is claimed."
OBJECT pidValue
MIN-ACCESS not-accessible
DESCRIPTION "Read-only access required if MPEG option
is claimed. Write access
Combes Expires January 9, 2008 [Page 55]
Internet-Draft DVB-RCS MIB July 2007
only required if also SNMPALL support is claimed."
OBJECT pidPoolRowStatus
MIN-ACCESS not-accessible
DESCRIPTION "Read-only access required if MPEG option
is claimed. Write access
only required if also SNMPALL support is claimed."
::= { rcstCompliances 1 }
===================================================================
-- units of conformance
====================================================================
===================================================================
-- object groups for rcst system
===================================================================
rcstSystemGroup OBJECT-GROUP
OBJECTS {
systemMibVersion,
systemLocation,
systemOduTxType,
systemOduRxType,
systemSatlabsOptions
}
STATUS current
DESCRIPTION "A collection of objects providing information
applicable for basic device management support."
::= { rcstGroups 1 }
rcstExtSystemGroup OBJECT-GROUP
OBJECTS {
systemOduAntennaSize,
systemOduAntennaGain,
systemOduSspa,
Combes Expires January 9, 2008 [Page 56]
Internet-Draft DVB-RCS MIB July 2007
systemOduRxBand,
systemOduRxLO,
systemOduTxLO,
installCwPower
}
STATUS current
DESCRIPTION "A collection of objects providing information
applicable for extended device management support."
::= { rcstGroups 2 }
===================================================================
-- object groups for rcst installation
===================================================================
rcstInstallGroup OBJECT-GROUP
OBJECTS {
installAntennaAlignmentState,
installCwFrequency,
installCwMaxDuration,
installCoPolReading,
installXPolReading,
installCoPolTarget,
installXPolTarget,
installStandByDuration,
installTargetEsNo,
}
STATUS current
DESCRIPTION "A collection of objects providing information
applicable for basic installation support."
::= { rcstGroups 3 }
rcstExtInstallGroup OBJECT-GROUP
OBJECTS {
networkInstallLogFileDownloadUrl,
networkInstallLogFileUploadUrl
}
STATUS current
DESCRIPTION "A collection of objects providing extended device
installation support."
::= { rcstGroups 4 }
===================================================================
Combes Expires January 9, 2008 [Page 57]
Internet-Draft DVB-RCS MIB July 2007
-- object groups for rcst networking
===================================================================
rcstNetworkGroup OBJECT-GROUP
OBJECTS {
networkOamIpAddr,
networkOamIpNetworkMask,
networkLanIpAddress,
networkLanIpMask,
networkConfigFileDownloadUrl,
networkConfigFileUploadUrl,
networkLogFileUploadUrl
}
STATUS current
DESCRIPTION "A collection of objects providing basic networking
management support."
::= { rcstGroups 5 }
rcstExtNetworkGroup OBJECT-GROUP
OBJECTS {
networkOamIpAddrAssign,
networkAirInterfaceDefaultGW,
networkNccMgtIpAddress
}
STATUS current
DESCRIPTION "A collection of objects providing extended
networking management support."
::= { rcstGroups 6 }
rcstDnsGroup OBJECT-GROUP
OBJECTS {
networkDnsServerIpAddress
}
STATUS current
DESCRIPTION "IP address of the DNS server to be used to resolve
URL's as needed."
::= { rcstGroups 7 }
===================================================================
Combes Expires January 9, 2008 [Page 58]
Internet-Draft DVB-RCS MIB July 2007
-- object groups for return link
===================================================================
rtnConfigGroup OBJECT-GROUP
OBJECTS {
rtnconfDefIfLevel
}
STATUS current
DESCRIPTION "A collection of objects providing basic return
link configuration support."
::= { rcstGroups 8 }
rtnExtConfigGroup OBJECT-GROUP
OBJECTS {
rtnconfMaxEirp
}
STATUS current
DESCRIPTION "A collection of objects providing extended return
link configuration support."
::= { rcstGroups 9 }
rtnStatusGroup OBJECT-GROUP
OBJECTS {
rcstRtnLinkStatus,
rtnstatusEbN0,
rtnstatusSFduration,
rtnstatusPayloadUnit
}
STATUS current
DESCRIPTION "A collection of objects allowing access to RTN
link status."
::= { rcstGroups 10 }
===================================================================
-- object groups for forward link
===================================================================
fwdConfigGroup OBJECT-GROUP
Combes Expires January 9, 2008 [Page 59]
Internet-Draft DVB-RCS MIB July 2007
OBJECTS {
fwdStartIndex,
fwdStartPopId,
fwdStartFrequency,
fwdStartPolar,
fwdStartFormat,
fwdStartModulation,
fwdStartRolloff,
fwdStartSymbolRate,
fwdStartInnerFec,
fwdStartRowStatus
}
STATUS current
DESCRIPTION "A collection of objects providing basic start
forward link configuration support."
::= { rcstGroups 11 }
fwdStatusGroup OBJECT-GROUP
OBJECTS {
fwdStatusIfIndex,
fwdStatusNetId,
fwdStatusCnr,
fwdStatusRowStatus
}
STATUS current
DESCRIPTION "A collection of objects providing basic forward
link status."
::= { rcstGroups 12 }
fwdExtStatusGroup OBJECT-GROUP
OBJECTS {
fwdStatusFormat,
fwdStatusFrequency,
fwdStatusPolar,
fwdStatusInnerFec,
fwdStatusSymbolRate,
fwdStatusRollOff,
fwdStatusModulation,
fwdStatusFecFrame,
fwdStatusPilot,
Combes Expires January 9, 2008 [Page 60]
Internet-Draft DVB-RCS MIB July 2007
fwdStatusBer,
fwdStatusRxPower,
rcstFwdLinkStatus
}
STATUS current
DESCRIPTION "A collection of objects providing extended forward
link status."
::= { rcstGroups 13 }
====================================================================
-- object groups for QOS
====================================================================
rcstQosGroup OBJECT-GROUP
OBJECTS {
pktClassIndex,
pktClassPhbAssociation,
phbIdentifier,
phbName,
phbRequestClassAssociation,
requestClassIndex,
requestClassName,
requestClassChanId,
requestClassVccVpi,
requestClassVccVci,
requestClassCra,
requestClassRbdcMax,
requestClassRbdcTimeout,
requestClassVbdcMax,
requestClassVbdcTimeout,
requestClassVBDCMaxBacklog
}
STATUS current
DESCRIPTION "A collection of objects providing basic access to
QOS configuration data."
::= { rcstGroups 14 }
rcstEnhancedClassifierGroup OBJECT-GROUP
OBJECTS {
pktClassIpProtocol,
pktClassIpScrAddr,
pktClassIpScrAddrMask,
Combes Expires January 9, 2008 [Page 61]
Internet-Draft DVB-RCS MIB July 2007
pktClassIpDstAddr,
pktClassIpDstAddrMask,
pktClassSrcPortLow,
pktClassSrcPortHigh,
pktClassDstPortLow,
pktClassDstPortHigh
}
STATUS current
DESCRIPTION "A collection of objects providing support for
management of the enhanced classifier."
::= { rcstGroups 15 }
rcstMpegQosGroup OBJECT-GROUP
OBJECTS {
requestClassPidPoolReference,
pidPoolIndex,
pidIndex,
pidValue,
pidPoolRowStatus
}
STATUS current
DESCRIPTION "A collection of objects providing access to MPEG
related link QOS configuration data."
::= { rcstGroups 16 }
rcstAvbdcRepQosGroup OBJECT-GROUP
OBJECTS {
requestClassAvbdcRepTime
}
STATUS current
DESCRIPTION "A collection of objects providing access to AVDBC
repeat related QOS configuration data."
::= { rcstGroups 17 }
rcstGlobalQosGroup OBJECT-GROUP
OBJECTS {
qosGlobalRbdcMax,
qosGlobalVBDCMax,
Combes Expires January 9, 2008 [Page 62]
Internet-Draft DVB-RCS MIB July 2007
qosGlobalVBDCMaxBacklog
}
STATUS current
DESCRIPTION "A collection of objects providing access to global
RCST QOS configuration data."
::= { rcstGroups 18 }
rcstGlobalAvbdcRepQosGroup OBJECT-GROUP
OBJECTS {
qosGlobalAvbdcRepTime
}
STATUS current
DESCRIPTION "A collection of objects providing access to global
AVDBC repeat related QOS configuration data."
::= { rcstGroups 19 }
rcstStrictQosGroup OBJECT-GROUP
OBJECTS {
qosChannelIdStrictDispatching
}
STATUS current
DESCRIPTION "A collection of objects allowing management of
strict channel ID dispatching."
::= { rcstGroups 20 }
===================================================================
-- object groups for rcst state
===================================================================
rcstStateGroup OBJECT-GROUP
OBJECTS {
rcstMode,
rcstFaultStatus,
rcstLogUpdated,
rcstSwDownloadStatus,
rcstCurrentSoftwareVersion,
rcstAlternateSoftwareVersion,
rcstActivatedConfigFileVersion,
rcstDownloadedConfigFileVersion
}
Combes Expires January 9, 2008 [Page 63]
Internet-Draft DVB-RCS MIB July 2007
STATUS current
DESCRIPTION "A collection of objects allowing access to RCST
state."
::= { rcstGroups 21 }
===================================================================
-- object groups for rcst control
===================================================================
rcstControlGroup OBJECT-GROUP
OBJECTS {
ctrlRebootCommand,
ctrlUserTrafficDisable,
ctrlCWEnable,
ctrlDownloadFileCommand,
ctrlUploadFileCommand,
ctrlActivateConfigFileCommand
}
STATUS current
DESCRIPTION "A collection of objects allowing basic RCST
control."
::= { rcstGroups 22 }
rcstExtControlGroup OBJECT-GROUP
OBJECTS {
ctrlRcstTxDisable,
ctrlOduTxReferenceEnable,
ctrlOduTxDCEnable,
ctrlOduRxDCEnable,
ctrlRcstLogonCommand,
ctrlRcstLogoffCommand
}
STATUS current
DESCRIPTION "A collection of objects allowing extended RCST
control."
::= { rcstGroups 23 }
END=
Combes Expires January 9, 2008 [Page 64]
Internet-Draft DVB-RCS MIB July 2007
4. Security Considerations
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments.
SNMP versions prior to SNMPv3 did not include adequate security. Even
if the network itself is secure (for example by using IPsec), even
then, there is no control as to who on the secure network is allowed
to access and GET/SET (read/change/create/delete) the objects in this
MIB module.
It is RECOMMENDED that implementers consider the security features
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
5. IANA Considerations
No action from IANA is needed.
6. Acknowledgments
The authors thank Gorry Fairhurst for advice in the preparation of
this document.
The authors recognize this document is a collective effort of the
SatLabs Group (www.satlabs.org).
Combes Expires January 9, 2008 [Page 65]
Internet-Draft DVB-RCS MIB July 2007
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997 (BEST
CURRENT PRACTICE).
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information,
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580, April
1999.
7.2. Informative References
[ISO-MPEG] ISO/IEC DIS 13818-1:2000, "Information Technology;
Generic Coding of Moving Pictures and Associated Audio
Information Systems", International Standardisation
Organisation (ISO).
[ETSI-DAT] EN 301 192, "Digital Video Broadcasting (DVB); DVB
Specifications for Data Broadcasting", European
Telecommunications Standards Institute (ETSI).
[ETSI-DVBS] EN 301 421 "Digital Video Broadcasting (DVB); Modulation
and Coding for DBS satellite systems at 11/12 GHz",
European Telecommunications Standards Institute (ETSI).
[ETSI-RCS] ETSI 301 791 "Digital Video Broadcasting (DVB);
Interaction Channel for Satellite Distribution Systems",
European Telecommunications Standards Institute (ETSI).
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
Combes Expires January 9, 2008 [Page 66]
Internet-Draft DVB-RCS MIB July 2007
[RFC4259] Montpetit, M.-J., Fairhurst, G., Clausen, H., Collini-
Nocker, B., and H. Linder, "A Framework for Transmission of
IP Datagrams over MPEG-2 Networks", RFC 4259, November
2005.
[SATLABS] SatLabs System Recommendations, version 2, December 2006.
Available at www.satlabs.org.
8. Authors' Addresses
Stephane Combes
ESTEC
European Space Agency
Keplerlaan 1 - - P.O. Box 299
2200 AG Noordwijk ZH
The Netherlands
Email: stephane.combes@esa.int
URL: telecom.esa.int
Petter Chr. Amundsen
VeriSat AS
P.O Box 1
1330 Fornebu
Norway
Email: pca@verisat.no
URL: www.verisat.no
Micheline Lambert
Advantech Satellite Networks
2341 boul. Alfred-Nobel
Saint-Laurent (Montreal,)H4S 2A9
Quebec, Canada
Email: micheline.lambert@advantechamt.com
URL: www.advantechsatnet.com
Combes Expires January 9, 2008 [Page 67]
Internet-Draft DVB-RCS MIB July 2007
Hans-Peter Lexow
STM Norway
Vollsveien 21
1366 Lysaker
Norway
Email: hlexow@stmi.com
URL: www.stmi.com
9. Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
10. Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Combes Expires January 9, 2008 [Page 68]
Internet-Draft DVB-RCS MIB July 2007
11. Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
Combes Expires January 9, 2008 [Page 69]
Internet-Draft DVB-RCS MIB July 2007
<<< RFC Ed Note: please remove the text below, prior to publications
>>>
Change Log.
Rev -00
- First draft, for comment by the community.
Rev -01
- Second draft, for comment by the community.
The MIB module is renamed DVBRCS-MIB to reflect that it covers more
than solely interface issues.
The MIB has been updated with
o a conformance section that captures the options
o structural changes and corrections to achieve this
o SYNTAX refinements where applicable
o UNITS declarations where applicable
Document reformatted to conform to I-D format conventions.
<<<End of RFC Ed Note >>
Combes Expires January 9, 2008 [Page 70]
