PCE Working Group                                               D. Dhody
Internet-Draft                                                    Y. Lee
Intended status: Informational                       Huawei Technologies
Expires: May 02, 2017                                      D. Ceccarelli
                                                                Ericsson
                                                                 J. Shin
                                                              SK Telecom
                                                                 D. King
                                                    Lancaster University
                                                     O. Gonzalez de Dios
                                                          Telefonica I+D
                                                        October 29, 2016


         Hierarchical Stateful Path Computation Element (PCE).
                  draft-dhodylee-pce-stateful-hpce-02

Abstract

   A Stateful Path Computation Element (PCE) maintains information on
   the current network state, including: computed Label Switched Path
   (LSPs), reserved resources within the network, and pending path
   computation requests. This information may then be considered when
   computing new traffic engineered LSPs, and for associated
   and dependent LSPs, received from Path Computation Clients (PCCs).

   The Hierarchical Path Computation Element (H-PCE) architecture,
   provides an architecture to allow the optimum sequence of
   inter-connected domains to be selected, and network policy to be
   applied if applicable, via the use of a hierarchical relationship
   between PCEs.

   Combining the capabilities of Stateful PCE and the Hierarchical PCE
   would be advantageous. This document describes general considerations
   and use cases for the deployment of Stateful PCE(s) using the
   Hierarchical PCE architecture.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months



Dhody, et al.               Expires May 2017                    [Page 1]


Internet-Draft               STATEFUL-HPCE                  October 2016


   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Hierarchical Stateful PCE . . . . . . . . . . . . . . . . . .   4
     3.1.  Passive Operations  . . . . . . . . . . . . . . . . . . .   4
     3.2.  Active Operations . . . . . . . . . . . . . . . . . . . .   7
     3.3.  PCE Initiation Operation  . . . . . . . . . . . . . . . .   8
       3.3.1.  Per Domain Stitched LSP . . . . . . . . . . . . . . .   8
   4.  Other Considerations  . . . . . . . . . . . . . . . . . . . .  10
     4.1.  Applicability to Inter-Layer  . . . . . . . . . . . . . .  10
     4.2.  Applicability to ACTN . . . . . . . . . . . . . . . . . .  11
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  12
   6.  Manageability Considerations  . . . . . . . . . . . . . . . .  12
     6.1.  Control of Function and Policy  . . . . . . . . . . . . .  12
     6.2.  Information and Data Models . . . . . . . . . . . . . . .  12
     6.3.  Liveness Detection and Monitoring . . . . . . . . . . . .  12
     6.4.  Verify Correct Operations . . . . . . . . . . . . . . . .  12
     6.5.  Requirements On Other Protocols . . . . . . . . . . . . .  12
     6.6.  Impact On Network Operations  . . . . . . . . . . . . . .  12
   7.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  12
   8.  Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  12
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  12
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  12
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  13
   Appendix A.  Contributor Addresses  . . . . . . . . . . . . . . .  14
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  14




Dhody, et al.               Expires May 2017                    [Page 2]


Internet-Draft               STATEFUL-HPCE                  October 2016


1.  Introduction

   The Path Computation Element communication Protocol (PCEP) provides
   mechanisms for Path Computation Elements (PCEs) to perform path
   computations in response to Path Computation Clients' (PCCs)
   requests.

   A stateful PCE is capable of considering, for the purposes of
   path computation, not only the network state in terms of links and
   nodes (referred to as the Traffic Engineering Database or TED) but
   also the status of active services (previously computed paths,
   and currently reserved resources, stored in the Label Switched
   Paths Database (LSPDB).

   [I-D.ietf-pce-stateful-pce-app] describes general considerations for
   a stateful PCE deployment and examines its applicability and
   benefits, as well as its challenges and limitations through a number
   of use cases.

   [I-D.ietf-pce-stateful-pce] describes a set of extensions to PCEP to
   provide stateful control.  A stateful PCE has access to not only the
   information carried by the network's Interior Gateway Protocol (IGP),
   but also the set of active paths and their reserved resources for its
   computations.  The additional state allows the PCE to compute
   constrained paths while considering individual LSPs and their
   interactions.  [I-D.ietf-pce-pce-initiated-lsp] describes the setup,
   maintenance and teardown of PCE-initiated LSPs under the stateful PCE
   model.

   [I-D.ietf-pce-stateful-pce] also describes the active stateful PCE.
   The active PCE functionality allows a PCE to reroute an existing
   LSP or make changes to the attributes of an existing LSP, or delegate
   control of specific LSPs to a new PCE.

   The ability to compute shortest constrained TE LSPs in Multiprotocol
   Label Switching (MPLS) and Generalized MPLS (GMPLS) networks across
   multiple domains has been identified as a key motivation for PCE
   development.  [RFC6805] describes a Hierarchical PCE (H-PCE)
   architecture which can be used for computing end-to-end paths for
   inter-domain MPLS Traffic Engineering (TE) and GMPLS Label Switched
   Paths (LSPs).  Within the Hierarchical PCE (H-PCE) architecture
   [RFC6805], the Parent PCE (P-PCE) is used to compute a multi-domain
   path based on the domain connectivity information.  A Child PCE
   (C-PCE) may be responsible for a single domain or multiple domains,
   it is used to compute the intra-domain path based on its domain
   topology information.

   This document presents general considerations for stateful PCE(s) in



Dhody, et al.               Expires May 2017                    [Page 3]


Internet-Draft               STATEFUL-HPCE                  October 2016


   hierarchical PCE architecture.  In particular, the behavior changes
   and additions to the existing stateful PCE mechanisms (including PCE-
   initiated LSP setup and active PCE usage) in the context of networks
   using the H-PCE architecture.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2.  Terminology

   The terminology is as per [RFC4655], [RFC5440], [RFC6805], and
   [I-D.ietf-pce-stateful-pce].

3.  Hierarchical Stateful PCE

   As described in [RFC6805], in the hierarchical PCE architecture, a
   P-PCE maintains a domain topology map that contains the child domains
   (seen as vertices in the topology) and their interconnections (links
   in the topology).  The P-PCE has no information about the content of
   the child domains.  Each child domain has at least one PCE capable of
   computing paths across the domain.  These PCEs are known as C-PCEs
   and have a direct relationship with the P-PCE.  The P-PCE builds the
   domain topology map either via direct configuration (allowing network
   policy to also be applied) or from learned information received from
   each C-PCE.

   [I-D.ietf-pce-stateful-pce] specifies new functions to support a
   stateful PCE.  It also specifies that a function can be initiated
   either from a PCC towards a PCE (C-E) or from a PCE towards a PCC
   (E-C).

   This document extends these functions to support H-PCE Architecture
   from a C-PCE towards a P-PCE (CE-PE) or from a P-PCE
   towards a C-PCE (PE-CE).  All PCE types herein (i.e., PE or CE)
   are assumed to be 'stateful PCE'.

   A number of interactions are expected in the Hierarchical Stateful
   PCE architecture, these include:

   LSP State Report (CE-PE):  a child stateful PCE sends an LSP state
      report to a Parent Stateful PCE whenever the state of a LSP
      changes.

   LSP State Synchronization (CE-PE):  after the session between the
      Child and Parent stateful PCEs is initialized, the P-PCE must



Dhody, et al.               Expires May 2017                    [Page 4]


Internet-Draft               STATEFUL-HPCE                  October 2016


      learn the state of C-PCE's TE LSPs.

   LSP Control Delegation (CE-PE,PE-CE):  a C-PCE grants to the
      P-PCE the right to update LSP attributes on one or more LSPs;
      the C-PCE may withdraw the delegation or the P-PCE may
      give up the delegation at any time.

   LSP Update Request (PE-CE):  a stateful P-PCE requests
      modification of attributes on a C-PCE's TE LSP.

   PCE LSP Initiation Request (PE-CE):  a stateful P-PCE requests
      C-PCE to initiate a TE LSP.

   Note that this hierarchy is recursive and thus a LSR could delegate
   the control to a PCE, which may delegate to its parent, which may
   further delegate it to its parent (if it exist or needed). Similarly
   update operations could also be applied recursively.

3.1.  Passive Operations

   Procedures as described in [RFC6805] are applied, where the ingress
   C-PCE sends a request to the P-PCE.  The P-PCE selects a set of
   candidate domain paths based on the domain topology and the state of
   the inter-domain links.  It then sends computation requests to the C-
   PCEs responsible for each of the domains on the candidate domain
   paths.  Each C-PCE computes a set of candidate path segments across
   its domain and sends the results to the P-PCE. The P-PCE uses this
   information to select path segments and concatenate them to derive
   the optimal end-to-end inter-domain path.  The end-to-end path is
   then sent to the C-PCE that received the initial path request, and
   this C-PCE passes the path on to the PCC that issued the original
   request.

   As per [I-D.ietf-pce-stateful-pce], PCC sends an LSP State Report
   carried on a PCRpt message to the C-PCE, indicating the LSP's status.
    The C-PCE MAY further propagate the State Report to the P-PCE.  A
   local policy at C-PCE MAY dictate which LSPs to be reported to the P-
   PCE.  The PCRpt message is sent from C-PCE to P-PCE.

   State synchronization mechanism as described in
   [I-D.ietf-pce-stateful-pce] and
   [I-D.ietf-pce-stateful-sync-optimizations] are applicable to PCEP
   session between C-PCE and P-PCE as well.

   Taking the sample hierarchical domain topology example from [RFC6805]
   as the reference topology for the entirety of this document.





Dhody, et al.               Expires May 2017                    [Page 5]


Internet-Draft               STATEFUL-HPCE                  October 2016


      -----------------------------------------------------------------
     |   Domain 5                                                      |
     |                              -----                              |
     |                             |PCE 5|                             |
     |                              -----                              |
     |                                                                 |
     |    ----------------     ----------------     ----------------   |
     |   | Domain 1       |   | Domain 2       |   | Domain 3       |  |
     |   |                |   |                |   |                |  |
     |   |        -----   |   |        -----   |   |        -----   |  |
     |   |       |PCE 1|  |   |       |PCE 2|  |   |       |PCE 3|  |  |
     |   |        -----   |   |        -----   |   |        -----   |  |
     |   |                |   |                |   |                |  |
     |   |            ----|   |----        ----|   |----            |  |
     |   |           |BN11+---+BN21|      |BN23+---+BN31|           |  |
     |   |   -        ----|   |----        ----|   |----        -   |  |
     |   |  |S|           |   |                |   |           |D|  |  |
     |   |   -        ----|   |----        ----|   |----        -   |  |
     |   |           |BN12+---+BN22|      |BN24+---+BN32|           |  |
     |   |            ----|   |----        ----|   |----            |  |
     |   |                |   |                |   |                |  |
     |   |         ----   |   |                |   |   ----         |  |
     |   |        |BN13|  |   |                |   |  |BN33|        |  |
     |    -----------+----     ----------------     ----+-----------   |
     |                \                                /               |
     |                 \       ----------------       /                |
     |                  \     |                |     /                 |
     |                   \    |----        ----|    /                  |
     |                    ----+BN41|      |BN42+----                   |
     |                        |----        ----|                       |
     |                        |                |                       |
     |                        |        -----   |                       |
     |                        |       |PCE 4|  |                       |
     |                        |        -----   |                       |
     |                        |                |                       |
     |                        | Domain 4       |                       |
     |                         ----------------                        |
     |                                                                 |
      -----------------------------------------------------------------

             Figure 1: Sample Hierarchical Domain Topology

   Steps 1 to 11 are exactly as described in section 4.6.2 (Hierarchical
   PCE End-to-End Path Computation Procedure) of [RFC6805], the
   following additional steps are added for stateful PCE:

   (1)  The Ingress LSR initiates the setup of the LSP as per the path
        and reports to the PCE1 the LSP status ("GOING-UP").



Dhody, et al.               Expires May 2017                    [Page 6]


Internet-Draft               STATEFUL-HPCE                  October 2016


   (2)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

   (3)  The Ingress LSR notifies the LSP state to PCE1 when the state is
        "UP".

   (4)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

3.2.  Active Operations


   [I-D.ietf-pce-stateful-pce] describes the case of active stateful
   PCE. The active PCE functionality uses two specific PCEP messages:

   o Update Request (PCUpd)
   o State Report (PCRpt)

   The first is sent by the PCE to a Path Computation Client (PCC) for
   modifying LSP attributes. The PCC sends back a PCRpt to acknowledge
   the requested operation. PCRpt has the same structure of PCNtf
   message.

   As per [I-D.ietf-pce-stateful-pce], Delegation is an operation to
   grant a PCE, temporary rights to modify a subset of LSP parameters on
   one or more PCC's LSPs.  The C-PCE may further choose to delegate
   to P-PCE based on a local policy.  The PCRpt message with "D"
   (delegate) flag is sent from C-PCE to P-PCE.

   To update an LSP, a PCE send to the PCC, an LSP Update Request using
   a PCUpd message.  For LSP delegated to the P-PCE via the child
   PCE, the P-PCE can use the same PCUpd message to request change
   to the C-PCE (the Ingress domain PCE), the PCE further propagates
   the update request to the PCC.

   The P-PCE uses the same mechanism described in Section 3.1 to compute
   the end to end path using PCReq and PCRep messages.

   The following additional steps are also initially performed,
   for active operations, again using the reference architecture
   described in Figure 1 (Sample Hierarchical Domain Topology).

   (1)  The Ingress LSR delegates the LSP to the PCE1 via PCRpt message
        with D flag set.

   (2)  The PCE1 further delegates the LSP to the P-PCE (PCE5).

   Steps 4 to 10 of section 4.6.2 of [RFC6805] are executed to determine



Dhody, et al.               Expires May 2017                    [Page 7]


Internet-Draft               STATEFUL-HPCE                  October 2016


   the end to end path.

   (3)  The P-PCE (PCE5) sends the update request to the C-PCE
        (PCE1) via PCUpd message.

   (4)  The PCE1 further updates the LSP to the Ingress LSR (PCC).

   (5)  The Ingress LSR initiates the setup of the LSP as per the path
        and reports to the PCE1 the LSP status ("GOING-UP").

   (6)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

   (7)  The Ingress LSR notifies the LSP state to PCE1 when the state is
        "UP".

   (8)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

3.3.  PCE Initiation Operation

   [I-D.ietf-pce-pce-initiated-lsp] describes the setup, maintenance and
   teardown of PCE-initiated LSPs under the stateful PCE model, without
   the need for local configuration on the PCC, thus allowing for a
   dynamic network that is centrally controlled and deployed.  To
   instantiate or delete an LSP, the PCE sends the Path Computation LSP
   Initiate Request (PCInitiate) message to the PCC.  In case of inter-
   domain LSP in Hierarchical PCE architecture, the initiation
   operations can be carried out at the P-PCE.  In which case after
   P-PCE finishes the E2E path computation, it can send the
   PCInitiate message to the C-PCE (the Ingress domain PCE), the PCE
   further propagates the initiate request to the PCC.

   The following additional steps are also initially performed,
   for PCE initiated operations, again using the reference
   architecture described in Figure 1 (Sample Hierarchical Domain
   Topology):

   (1)  The P-PCE (PCE5) is requested to initiate a LSP.

   Steps 4 to 10 of section 4.6.2 of [RFC6805] are executed to determine
   the end to end path.

   (2)  The P-PCE (PCE5) sends the initiate request to the child
        PCE (PCE1) via PCInitiate message.

   (3)  The PCE1 further propagates the initiate message to the Ingress
        LSR (PCC).



Dhody, et al.               Expires May 2017                    [Page 8]


Internet-Draft               STATEFUL-HPCE                  October 2016


   (4)  The Ingress LSR initiates the setup of the LSP as per the path
        and reports to the PCE1 the LSP status ("GOING-UP").

   (5)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

   (6)  The Ingress LSR notifies the LSP state to PCE1 when the state is
        "UP".

   (7)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

3.3.1.  Per Domain Stitched LSP

   The hierarchical PCE architecture as per [RFC6805] is primarily used
   for E2E LSP.  With PCE-Initiated capability, another mode of
   operation is possible, where multiple intra-domain LSPs are initiated
   in each domain which are further stitched to form an E2E LSP.  The
   P-PCE sends PCInitiate message to each C-PCE separately to
   initiate individual LSP segments along the domain path.  These
   individual per domain LSP are stitched together by some mechanism,
   which is out of scope of this document. The P-PCE may also send
   the PCInitiate message to the ingress C-PCE to initiate the E2E
   LSP separately.

   The following additional steps are also initially performed,
   for the Per Domain stiched LSP operation, again using the reference
   architecture described in Figure 1 (Sample Hierarchical Domain
   Topology):

   (1)  The P-PCE (PCE5) is requested to initiate a LSP.

   Steps 4 to 10 of section 4.6.2 of [RFC6805] are executed to determine
   the end to end path, which are broken into per-domain LSPs say -

   o  S-BN41

   o  BN41-BN33

   o  BN33-D

   It should be noted that the P-PCE MAY use other mechanisms to
   determine the suitable per-domain LSPs (apart from [RFC6805]).

   For LSP (BN33-D)

   (2)  The P-PCE (PCE5) sends the initiate request to the child
        PCE (PCE3) via PCInitiate message for LSP (BN33-D).



Dhody, et al.               Expires May 2017                    [Page 9]


Internet-Draft               STATEFUL-HPCE                  October 2016


   (3)  The PCE3 further propagates the initiate message to BN33.

   (4)  BN33 initiates the setup of the LSP as per the path and reports
        to the PCE3 the LSP status ("GOING-UP").

   (5)  The PCE3 further reports the status of the LSP to the P-PCE
        (PCE5).

   (6)  The node BN33 notifies the LSP state to PCE3 when the state is
        "UP".

   (7)  The PCE3 further reports the status of the LSP to the P-PCE
        (PCE5).

   For LSP (BN41-BN33)

   (8)  The P-PCE (PCE5) sends the initiate request to the child PCE
        (PCE4) via PCInitiate message for LSP (BN41-BN33).

   (9)  The PCE4 further propagates the initiate message to BN41.

   (10) BN41 initiates the setup of the LSP as per the path and reports
        to the PCE4 the LSP status ("GOING-UP").

   (11) The PCE4 further reports the status of the LSP to the P-PCE
        (PCE5).

   (l2) The node BN41 notifies the LSP state to PCE4 when the state is
        "UP".

   (13) The PCE4 further reports the status of the LSP to the P-PCE
        (PCE5).

   For LSP (S-BN41)

   (14)  The P-PCE (PCE5) sends the initiate request to the child
        PCE (PCE1) via PCInitiate message for LSP (S-BN41).

   (15)  The PCE1 further propagates the initiate message to node S.

   (16)  S initiates the setup of the LSP as per the path and reports to
        the PCE1 the LSP status ("GOING-UP").

   (17)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

   (18)  The node S notifies the LSP state to PCE1 when the state is
        "UP".



Dhody, et al.               Expires May 2017                   [Page 10]


Internet-Draft               STATEFUL-HPCE                  October 2016


   (19)  The PCE1 further reports the status of the LSP to the P-PCE
        (PCE5).

   Additionally:

   (20) Once P-PCE receives report of each per-domain LSP, it
        should use some stitching mechanism, which is out of scope of
        this document. In this step, P-PCE (PCE5) could also initiate
        an E2E LSP (S-D) by sending the PCInitiate message to Ingress
        C-PCE (PCE1).


4.  Other Considerations

4.1.  Applicability to Inter-Layer

   [RFC5623] describes a framework for applying the PCE-based
   architecture to inter-layer (G)MPLS traffic engineering.  The H-PCE
   Stateful architecture with stateful P-PCE coordinating with the
   stateful C-PCEs of higher and lower layer is shown in the figure
   below.

                                                     +----------+
                                                    /| Parent   |
                                                  /  | PCE      |
                                                /    +----------+
                                              /        / Stateful
                                             /       /
                                           /        /
                                          /       /
                          Stateful +---+/        /
                          Child   + PCE +      /
                          PCE Hi  + Hi  +     /
                                   +---+    /
          +---+    +---+                   /      +---+    +---+
         + LSR +--+ LSR +........................+ LSR +--+ LSR +
         + H1  +  + H2  +                 /      + H3  +  + H4  +
          +---+    +---+\          +---+/        /+---+    +---+
                         \        + PCE +       /
                          \       + Lo  +      /
                Stateful   \       +---+      /
                C-PCE   \                /
                Lo           \+---+    +---+/
                             + LSR +--+ LSR +
                             + L1  +  + L2  +
                              +---+    +---+

                 Figure 2: Sample Inter-Layer Topology



Dhody, et al.               Expires May 2017                   [Page 11]


Internet-Draft               STATEFUL-HPCE                  October 2016


   All procedures described in Section 3 are applicable to inter-layer
   path setup as well.

4.2.  Applicability to ACTN

   [I-D.ietf-teas-actn-framework] describes framework for
   Abstraction and Control of TE Networks (ACTN), where each Physical
   Network Controller (PNC) is equivalent to C-PCE and P-PCE is
   the Multi-Domain Service Coordinator (MDSC).  The Per domain stitched
   LSP as per the Hierarchical PCE architecture described in
   Section 3.3.1 and Section 4.1 is well suited for ACTN.

   [I-D.dhody-pce-applicability-actn] examines the applicability of PCE
   to the ACTN framework. To support the function of multi domain
   coordination via hierarchy, the stateful hierarchy of PCEs plays a
   crucial role.

   In ACTN framework, Customer Network Controller (CNC) can request the
   MDSC to check if there is a possibility to meet Virtual Network (VN)
   requirements (before requesting for VN provision).  The H-PCE
   architecture as described in [RFC6805] can supports via the use of
   PCReq and PCRep messages between the P-PCE and C-PCEs.

5.  Scalability Considerations

   It should be noted that if all the C-PCEs would report all the LSPs
   in their domain, it could lead to scalability issues for the P-PCE.
   Thus it is recommended to only report the LSPs which are involved in
   H-PCE, i.e. the LSPs which are either delegated to the P-PCE or
   initiated by the P-PCE.

6.  Security Considerations

   TBD.

7.  Manageability Considerations

7.1.  Control of Function and Policy

   TBD.

7.2.  Information and Data Models

   TBD.

7.3.  Liveness Detection and Monitoring

   TBD.



Dhody, et al.               Expires May 2017                   [Page 12]


Internet-Draft               STATEFUL-HPCE                  October 2016


7.4.  Verify Correct Operations

   TBD.

7.5.  Requirements On Other Protocols

   TBD.

7.6.  Impact On Network Operations

   TBD.

8.  IANA Considerations

   There are no IANA considerations.

9.  Acknowledgments

   Thanks to Manuela Scarella, Haomian Zheng, Sergio Marmo, Stefano
   Parodi, Giacomo Agostini, Jeff Tantsura and Rajan Rao for
   suggestions.

10.  References

10.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC5440]  Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
              Element (PCE) Communication Protocol (PCEP)", RFC 5440,
              DOI 10.17487/RFC5440, March 2009,
              <http://www.rfc-editor.org/info/rfc5440>.


   [RFC6805]  King, D., Ed. and A. Farrel, Ed., "The Application of the
              Path Computation Element Architecture to the Determination
              of a Sequence of Domains in MPLS and GMPLS", RFC 6805, DOI
              10.17487/RFC6805, November 2012,
              <http://www.rfc-editor.org/info/rfc6805>.

   [I-D.ietf-pce-stateful-pce]
              Crabbe, E., Minei, I., Medved, J., and R. Varga, "PCEP
              Extensions for Stateful PCE", draft-ietf-pce-stateful-
              pce-16 (work in progress), September 2016.




Dhody, et al.               Expires May 2017                   [Page 13]


Internet-Draft               STATEFUL-HPCE                  October 2016


   [I-D.ietf-pce-pce-initiated-lsp]
              Crabbe, E., Minei, I., Sivabalan, S., and R. Varga, "PCEP
              Extensions for PCE-initiated LSP Setup in a Stateful PCE
              Model", draft-ietf-pce-pce-initiated-lsp-07 (work in
              progress), July 2016.

10.2.  Informative References

   [RFC4655]  Farrel, A., Vasseur, J., and J. Ash, "A Path Computation
              Element (PCE)-Based Architecture", RFC 4655,
              DOI 10.17487/RFC4655, August 2006,
              <http://www.rfc-editor.org/info/rfc4655>.

   [RFC5623]  Oki, E., Takeda, T., Le Roux, JL., and A. Farrel,
              "Framework for PCE-Based Inter-Layer MPLS and GMPLS
              Traffic Engineering", RFC 5623, DOI 10.17487/RFC5623,
              September 2009, <http://www.rfc-editor.org/info/rfc5623>.

   [I-D.ietf-pce-stateful-pce-app]
              Zhang, X. and I. Minei, "Applicability of a Stateful Path
              Computation Element (PCE)", draft-ietf-pce-stateful-pce-
              app-07 (work in progress), September 2016.

   [I-D.ietf-pce-stateful-sync-optimizations]
              Crabbe, E., Minei, I., Medved, J., Varga, R., Zhang, X.,
              and D. Dhody, "Optimizations of Label Switched Path State
              Synchronization Procedures for a Stateful PCE", draft-
              ietf-pce-stateful-sync-optimizations-06 (work in
              progress), October 2016.

   [I-D.ietf-teas-actn-framework]
              Ceccarelli D. and Y. Lee, "Framework for Abstraction and
              Control of Transport Networks", draft-ietf-teas-
              actn-framework-01 (work in progress), October 2016.

   [I-D.dhody-pce-applicability-actn]
              Dhody, D., Lee, Y., and D. Ceccarelli, "Applicability of
              Path Computation Element (PCE) for Abstraction and
              Control of TE Networks (ACTN)",  draft-dhody-pce-
              applicability-actn-01 (work in progress), October 2016.











Dhody, et al.               Expires May 2017                   [Page 14]


Internet-Draft               STATEFUL-HPCE                  October 2016


Appendix A.  Contributor Addresses

   Avantika
   Huawei Technologies
   Divyashree Techno Park, Whitefield
   Bangalore, Karnataka  560066
   India

   EMail: avantika.sushilkumar@huawei.com

   Xian Zhang
   Huawei Technologies
   Bantian, Longgang District
   Shenzhen, Guangdong  518129
   P.R.China

   EMail: zhang.xian@huawei.com

   Udayasree Palle
   Huawei Technologies
   Divyashree Techno Park, Whitefield
   Bangalore, Karnataka  560066
   India

   EMail: udayasree.palle@huawei.com

Authors' Addresses

   Dhruv Dhody
   Huawei Technologies
   Divyashree Techno Park, Whitefield
   Bangalore, Karnataka  560066
   India

   EMail: dhruv.ietf@gmail.com


   Young Lee
   Huawei Technologies
   5340 Legacy Drive, Building 3
   Plano, TX  75023
   USA

   EMail: leeyoung@huawei.com


   Daniele Ceccarelli
   Ericsson



Dhody, et al.               Expires May 2017                   [Page 15]


Internet-Draft               STATEFUL-HPCE                  October 2016


   Torshamnsgatan,48
   Stockholm
   Sweden

   EMail: daniele.ceccarelli@ericsson.com

   Jongyoon Shin
   SK Telecom
   6 Hwangsaeul-ro, 258 beon-gil, Bundang-gu, Seongnam-si,
   Gyeonggi-do  463-784
   Republic of Korea

   EMail: jongyoon.shin@sk.com


   Dan King
   Lancaster University
   UK

   EMail: d.king@lancaster.ac.uk

   Oscar Gonzalez de Dios
   Telefonica I+D
   Don Ramon de la Cruz 82-84
   Madrid,   28045
   Spain

   Phone: +34913128832
   Email: ogondio@tid.es






















Dhody, et al.               Expires May 2017                   [Page 16]