BESS WorkGroup                                                    D. Rao
Internet-Draft                                                S. Agrawal
Intended status: Informational                               C. Filsfils
Expires: August 13, 2021                                   K. Talaulikar
                                                           Cisco Systems
                                                        February 9, 2021


               BGP Color-Aware Routing Problem Statement
              draft-dskc-bess-bgp-car-problem-statement-01

Abstract

   This document explores the scope, use-cases and requirements for a
   BGP based routing solution to establish end-to-end intent-aware paths
   across a multi-domain service provider network environment.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on August 13, 2021.

Copyright Notice

   Copyright (c) 2021 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.



Rao, et al.              Expires August 13, 2021                [Page 1]


Internet-Draft          BGP CAR Problem Statement          February 2021


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Objective . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.2.  State-of-the-art  . . . . . . . . . . . . . . . . . . . .   4
       1.2.1.  Color . . . . . . . . . . . . . . . . . . . . . . . .   4
       1.2.2.  Colored vs Color-Aware  . . . . . . . . . . . . . . .   5
       1.2.3.  Per-Destination and Per-Flow Steering . . . . . . . .   5
     1.3.  Why a BGP-based alternative is needed . . . . . . . . . .   6
     1.4.  Color Domains . . . . . . . . . . . . . . . . . . . . . .   6
     1.5.  BGP Color-Aware Routing . . . . . . . . . . . . . . . . .   6
   2.  Intent bound to a Color . . . . . . . . . . . . . . . . . . .   6
   3.  BGP CAR Use-cases . . . . . . . . . . . . . . . . . . . . . .   7
     3.1.  BGP Transport CAR . . . . . . . . . . . . . . . . . . . .   7
       3.1.1.  Use-case of minimization of a cost metric vs a
               latency metric  . . . . . . . . . . . . . . . . . . .   8
       3.1.2.  Use-case of exclusion/inclusion of link affinity  . .  10
       3.1.3.  Use-case of exclusion/inclusion of domains  . . . . .  10
       3.1.4.  Use-case of virtual network function chains in local
               and core domains  . . . . . . . . . . . . . . . . . .  11
     3.2.  BGP VPN CAR . . . . . . . . . . . . . . . . . . . . . . .  12
       3.2.1.  Use-case of minimization of a cost metric vs a
               latency metric  . . . . . . . . . . . . . . . . . . .  15
       3.2.2.  Use-case of exclusion/inclusion of link affinity  . .  16
       3.2.3.  Use-case of virtual network function chains in local
               and core domains  . . . . . . . . . . . . . . . . . .  17
   4.  Deployment Requirements . . . . . . . . . . . . . . . . . . .  18
   5.  Scalability . . . . . . . . . . . . . . . . . . . . . . . . .  19
     5.1.  Scale Requirements  . . . . . . . . . . . . . . . . . . .  19
     5.2.  Scale Analysis  . . . . . . . . . . . . . . . . . . . . .  20
   6.  Network Availability  . . . . . . . . . . . . . . . . . . . .  22
   7.  BGP Protocol Requirements . . . . . . . . . . . . . . . . . .  23
   8.  Future Considerations . . . . . . . . . . . . . . . . . . . .  24
   9.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  24
   10. References  . . . . . . . . . . . . . . . . . . . . . . . . .  25
     10.1.  Normative References . . . . . . . . . . . . . . . . . .  25
     10.2.  Informative References . . . . . . . . . . . . . . . . .  28
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  29

1.  Introduction

1.1.  Objective

   This document explores the scope, use-cases and requirements for a
   BGP based routing solution to establish end-to-end intent-aware paths
   across a multi-domain service provider network environment.





Rao, et al.              Expires August 13, 2021                [Page 2]


Internet-Draft          BGP CAR Problem Statement          February 2021


   The targeted design outcome is to define the technology and protocol
   extensions that may be required in a manner that addresses the widest
   application.

   To introduce the problem space that the document focuses on, let us
   start with the BGP-based delivery of an intent across several SR-
   MPLS/MPLS domains.

          +-----+                +-----+     V/v via PE2  +-----+
   .......|S-RR1|<...............|S-RR2|<.................|S-RR3| <..
   :      +-----+                +-----+     Color C      +-----+   :
   :                                                                :
   :                                                                :
+--:----------+-------------+--------------+-------------+----------:--+
|  :          |             |              |             |          :  |
|  :          |             |              |             |          :  |
|  :        +---+         +---+          +---+         +---+        :  |
|  :        |121|         |231|          |341|         |451|        :  |
|  :        +---+         +---+          +---+         +---+        :  |
|----+        |             |              |             |        +----|
| PE1|        |             |              |             |        |PE2 |
|----+        |             |              |             |        +----|
|           +---+         +---+          +---+         +---+           |
|           |122|         |232|          |342|         |452|           |
|           +---+         +---+          +---+         +---+           |
|  Access     |   Metro     |   Core       |   Metro     |   Access    |
|  domain 1   |   domain 2  |   domain 3   |   domain 4  |   domain 5  |
+-------------+-------------+--------------+-------------+-------------+
iPE         iBRM          iBRC           eBRC           eBRM         ePE

       Figure 1: Reference large-scale multi-domain network topology

   The figure above shows a reference large-scale multi-domain network
   topology.  PE1 and PE2 are PEs; the other nodes are border routers
   (BR) between domains in different tiers of the network.  A VPN route
   is advertised via service RRs (S-RR) between an egress PE (PE2) and
   an ingress PE (PE1).

   BGP must provide reachability from PE1 to PE2 based on various
   intent.  For instance, BGP may provide reachability to PE2 using
   either low latency or best effort.

   A VPN route having a requirement of low latency routing will select
   the BGP reachability information to PE2 that is based on low latency.

   The problem space is then widened to include any intent (including
   NFV chains and their location), any dataplane and the application of




Rao, et al.              Expires August 13, 2021                [Page 3]


Internet-Draft          BGP CAR Problem Statement          February 2021


   the intent-based routing to the Service/VPN routes.  All of this is
   detailed in the rest of the document.

1.2.  State-of-the-art

   The following solution is widely deployed -
   [I-D.ietf-spring-segment-routing-policy]:

   o  In reference figure above, an Egress PE PE2 advertises a BGP VPN
      route V/v with a BGP Color Extended Community C
      [I-D.ietf-idr-tunnel-encaps] to indicate the service intent that
      PE2 requests for the traffic bound to V/v.  Note: The Color
      Extended Community may be applied to any BGP service route.  For
      simplicity in this document, we will use a VPN route example.

   o  An ingress PE1 steers V-destined packets onto an SR Policy bound
      to (C, PE2).

   o  C may express any of the following requirements:

      *  Minimization of a cost metric vs a latency metric.

      *  Exclusion/Inclusion of SRLG and/or Link Affinity.

         +  In inter-domain context, exclusion/inclusion of entire
            domains.

      *  Inclusion of virtual network function chains
         [I-D.ietf-spring-sr-service-programming].

   o  An SR-PCE (or a set of them) computes the end-to-end path and
      installs it at PE1 as an SR Policy.  The end-to-end path may
      seamlessly cross multiple domains.

   The SR-PCE solution being defined at the IETF [RFC8664]and being
   widely deployed is reminded in this introduction as a useful "state-
   of-the-art" context to consider when defining the BGP-based
   alternative solution.

1.2.1.  Color

   The solution must reuse the Color concept defined in [I-D.ietf-
   spring-segment-routing-policy].  The color is a 32-bit numerical
   value that, today, associates an SR-policy with an intent (e.g., low
   latency).






Rao, et al.              Expires August 13, 2021                [Page 4]


Internet-Draft          BGP CAR Problem Statement          February 2021


1.2.2.  Colored vs Color-Aware

   The solution must support the ability to distinguish BGP routes that
   require the usage of a particular intent from BGP routes that are
   actually satisfying a particular intent.  Hence, this document
   defines the notion of colored and color-aware routes.

   o  Colored: Egress PE PE2 colored its BGP VPN route V/v to indicate
      the intent that it requests for the traffic bound to V/v.

   o  Color-Aware: A new BGP solution which signals multiple "ways" to
      reach a given destination (e.g.  PE2)

   o  Steering a colored VPN route to a color-aware route

      *  If PE2 signals a VPN route V/v with color C

      *  If PE1 installs that VPN route

      *  If PE1 learns about a BGP Color-Aware Route R/r to PE2 for
         color C

      *  Then PE1 steers packets destined to V/v via R/r

   o  Note the similarity with the state-of-the-art reference:

      *  The steering onto an SR Policy bound to (C, PE2) is replaced by
         the steering on a Color-Aware BGP route (C, PE2)

      *  The data model is the same "resolution via (C, PE2)"

      *  The difference is how the (C, PE2) path is obtained: BGP
         signaling vs SR-PCE signaling

1.2.3.  Per-Destination and Per-Flow Steering

   Ingress PE PE1 steers packets destined for a service (VPN) route V/v
   via BGP Color-Aware Route R/r to PE2

   o  Per-Destination Steering: Incoming packets on PE1 match BGP
      service route V/v to be steered based on the destination IP
      address of the packets.

   o  Per-Flow Steering: Incoming packets on PE1 match BGP service route
      V/v to be steered based on the combination of the destination IP
      address and additional elements in the packet header (i.e., IP
      flow).  Such a packet lookup may recurse on a forwarding array
      where some of the entries are BGP color-aware routes to PE2.  A



Rao, et al.              Expires August 13, 2021                [Page 5]


Internet-Draft          BGP CAR Problem Statement          February 2021


      given flow is mapped to a specific entry in this array i.e. via a
      specific BGP color-aware route to PE2.

1.3.  Why a BGP-based alternative is needed

   o  An operator with an existing Seamless-MPLS/BGP-LU deployment
      [I-D.ietf-mpls-seamless-mpls] may consider a BGP based extension
      as a more incremental approach.

   o  There may be an expectation that BGP would support a larger scale.

   o  Opacity of a remote domain due to trust boundaries within an
      inter-domain construction.

1.4.  Color Domains

   With the use of Color to represent intent, it is useful to describe
   the concept of a color domain distinct from a network domain.

   o  Domain: A domain (or network domain) refers to a unit of isolation
      or hierarchy in the network topology; for example, access, metro
      and or core domains.  From a routing perspective, a domain may
      have a distinct IGP area or instance; or a distinct BGP ASN.

   o  Color Domain: A color domain may represent a collection of one or
      more network domains with a single, consistent color/intent
      mapping.

   o  Color re-mapping may happen at color domain boundaries.

   o  Deployments under a single authority are expected to use the same
      color/intent mapping across all network domains.

   A solution must distinguish the actual protocol boundaries (IGP, ASN)
   from the color domain boundaries.

1.5.  BGP Color-Aware Routing

   A BGP solution that is solving this problem statement is called BGP
   Color-Aware Routing, and is referred to as BGP CAR in this document.

2.  Intent bound to a Color

   The BGP CAR solution must support the following intents bound to a
   color:

   o  Minimization of a cost metric vs a latency metric




Rao, et al.              Expires August 13, 2021                [Page 6]


Internet-Draft          BGP CAR Problem Statement          February 2021


      *  Minimization of different metric types, static and dynamic

   o  Exclusion/Inclusion of SRLG and/or Link Affinity and/or minimum
      MTU

   o  In the inter-domain context, exclusion/inclusion of entire domains

   o  Inclusion of one or several virtual network function chains

      *  Located in a regional domain and/or core domain, in a DC

   o  Localization of the virtual network function chains

      *  Some functions may be desired in the regional DC or vice versa

   o  Per-Destination and Per-Flow steering

3.  BGP CAR Use-cases

   The BGP CAR route may be a transport route or a service route (in
   this document, we use the term VPN instead of service for
   simplicity).

3.1.  BGP Transport CAR

   o  Transport Intent

      *  Intent-aware routing between PEs connected across multiple
         transit domains

         +  Set up BGP based end-to-end paths stitching intent-aware
            intra-domain segments

   o  The network diagram below illustrates the reference network
      topology used in this section for Transport CAR:
















Rao, et al.              Expires August 13, 2021                [Page 7]


Internet-Draft          BGP CAR Problem Statement          February 2021


        +-----+                +-----+                  +-----+
   .....|S-RR1| <............. |S-RR2| <............... |S-RR3| <...
   :    +-----+                +-----+                  +-----+    :
   :                                                               :
   :                                                               :
   :                                                               :
+--:--------------+       +-----------------+       +--------------:--+
|  :              |       |                 |       |              :  |
|  :              |       |                 |       |              :  |
|  :          +---|  D=20 |---+         +---|  D=25 |---+          :  |
|  :          |121|-------|211|         |231|-------|321|          :  |
|  :          +---| \   / |---+         +---| \   / |---+          :  |
|----+            |  \ /  |                 |  \ /  |            +----|
|PE11|            |   V   |                 |   V   |            |PE31|
|----+            |  / \  |                 |  / \  |            +----|
|             +---| /   \ |---+         +---| /   \ |---+             |
|             |122|-------|212|         |232|-------|322|             |
|             +---|  D=15 |---+         +---|  D=10 |---+             |
|                 |       |                 |       |                 |
|    Domain 1     |       |    Domain 2     |       |    Domain 3     |
+-----------------+       +-----------------+       +------------------+

                Figure 2: Transport CAR Reference Topology

      The following network design assumptions apply to the reference
      topology above, as an example:

      *  Independent ISIS/OSPF SR instance in each domain.

      *  eBGP peering link between ASBRs (121-211, 121-212, 122-211,
         122-212, 231-321, 231-322, 232-321 and 232-322).

      *  Peering links have equal cost metric.

      *  Peering links have delay configured or measured as shown by
         "D".  D=50 for cross peering links.

      *  VPN service is running from PE31 to PE11 via service RRs (S-RRn
         in figure).

   o  The following sections illustrate a few examples of intent use-
      cases applicable to transport routes.

3.1.1.  Use-case of minimization of a cost metric vs a latency metric

   o  In the reference topology of Figure 2

         Each domain has Algo 0 and Flex Algo 128



Rao, et al.              Expires August 13, 2021                [Page 8]


Internet-Draft          BGP CAR Problem Statement          February 2021


         Algo 0 is for minimum cost metric(cost optimized).

         Flex Algo 128 definition is for minimum delay (low latency).

   o  Cost Optimized

      *  Color C1 - Minimum cost intent.  (Here, a BGP CAR route with
         Color C1 is being used, instead of BGP-LU.)

      *  On PE11, VPN routes colored with C1 are steered via (C1, PE31)
         BGP CAR route

         +  BGP CAR for C1 sets up path(s) between PEs for end-to-end
            minimum cost.

         +  (2) These paths traverse over intra-domain Algo 0 in each
            domain and account for the peering link cost between ASBRs.

         +  Example: PE11 learns (C1, PE31) CAR route via several equal
            paths:

            1.  One such path is through FA0 to node 121, links 121-211,
                FA0 to 231, link 231-321, FA0 to PE31

            2.  Another such path is through FA0 to node 122, link
                122-212, FA0 to 232, link 232-322, FA0 to PE31.

   o  Minimize latency

      *  Color C2 - Minimum latency intent.

      *  On PE11, VPN routes colored with C2 are steered via (C2, PE31)
         BGP CAR route.

         +  BGP CAR for C2 advertises paths between PEs for minimum end-
            to-end delay.

         +  (2) These paths traverse over intra-domain Flex Algo 128 in
            each domain and account for peering link delay between
            ASBRs.

         +  (3) Example: PE11 learns (C2, PE31) BGP CAR route and best
            path is through FA128 to node 122, link 122-212, FA128 to
            232, link 232-322, FA128 to PE31.







Rao, et al.              Expires August 13, 2021                [Page 9]


Internet-Draft          BGP CAR Problem Statement          February 2021


3.1.2.  Use-case of exclusion/inclusion of link affinity

   o  Color C3 - Intent to Minimize cost metric and avoid purple links

   o  In the reference topology of Figure 2

         Each domain has Flex Algo 129 and some links have purple
         affinity.

         Flex Algo 129 definition is set to minimum cost metric and
         avoid purple links (within domain).

         Peering cross links are colored purple by policy.

   o  On PE11, VPN routes colored with C3 are steered via (C3, PE31) BGP
      CAR route.

      *  BGP CAR for C3 sets up paths between PEs for minimum end-to-end
         cost and avoiding purple link affinity.

      *  These paths traverse over intra domain Flex Algo 129 in each
         domain and accounts for peering link cost between ASBR and
         avoiding purple links.

      *  Example: PE11 learns (C3, PE31) BGP CAR route via 2 paths.

         1.  First path is through FA 129 to node 121, link 121-211,
             FA129 to 231, link 231-321, FA129 to PE31.

         2.  Second path is through FA129 to node 122, link 122-212,
             FA129 to 232, link 232-322, FA129 to PE31.

3.1.3.  Use-case of exclusion/inclusion of domains


















Rao, et al.              Expires August 13, 2021               [Page 10]


Internet-Draft          BGP CAR Problem Statement          February 2021


         +-----+                +-----+                 +-----+
     ....|S-RR1| <............. |S-RR2| <.............. |S-RR3| <....
     :   +-----+                +-----+                 +-----+     :
     :                                                              :
     :                      +----------------+                      :
     :                      |                |                      :
  +--:--------------+       |---+        +---|       +--------------:--+
  |  :              |   |---|211|        |241|---|   |              :  |
  |  :              |   |   |---+        +---|   |   |              :  |
  |  :          +---|   |   |    Domain 2    |   |   |---+          :  |
  |  :          |121|---|   +----------------+   |---|421|          :  |
  |  :          +---|                                |---+          :  |
  |----+            |                                |            +----|
  |PE11|            |                                |            |PE41|
  |----+            |                                |            +----|
  |             +---|                                |---+             |
  |             |131|---|   +----------------+   |---|431|             |
  |             +---|   |   |                |   |   |---+             |
  |                 |   |   |---+        +---|   |   |                 |
  |    Domain 1     |   |---|311|        |341|---|   |      Domain 4   |
  +-----------------+       |---+        +---|       +-----------------+
                            |   Domain 3     |
                            +----------------+

                                 Figure 3

   Color C4 - Avoid sending selected traffic via Domain 3

   o  VPN routes advertised from PEs with Color C4

   o  BGP CAR for Color C4 should only set up paths between PE11 and
      PE41 that exclude Domain 3

3.1.4.  Use-case of virtual network function chains in local and core
        domains
















Rao, et al.              Expires August 13, 2021               [Page 11]


Internet-Draft          BGP CAR Problem Statement          February 2021


          ____                      ____
         /    \                    /    \
        | NFV1 |                  | NFV2 |
         \    /                    \    /
  +---------------------+  +--------------------+  +-------------------+
  |      |E11|          |  |       |E21|        |  |                   |
  |      +---+          |  |       +---+        |  |                   |
  |                     |  |                    |  |                   |
  |                     |  |                    |  |                   |
  |----+              +------+                +------+            +----|
  |PE11|              | 121  |                | 231  |            |PE31|
  |----+              +------+                +------+            +----|
  |                     |  |                    |  |                   |
  |                     |  |                    |  |                   |
  |                     |  |                    |  |                   |
  |                     |  |                    |  |                   |
  |      Domain 1       |  |      Domain 2      |  |     Domain 3      |
  +---------------------+  +--------------------+  +-------------------+

                                 Figure 4

   o  Color intent

      *  C5 - Routing via min-cost paths

      *  C6 - Routing via a local NFV service chain situated at E11

      *  C7 - Routing via a centrally located NFV service chain situated
         at E21

   o  Forwarding of packets from PE11 towards PE31:

      *  (C5, PE31) mapped packets are sent via nodes 121, 231 to PE31

      *  (C6, PE31) mapped packets are sent to E11 and then post-service
         chain, via 121, 231 to PE31

      *  (C7, PE31) mapped packets are sent via 121 to E21 and then
         post-service chain, via 231 to PE31

3.2.  BGP VPN CAR

   o  VPN (Service layer) intent

      *  Extend the signaling of intent awareness end-to-end: CE site to
         CE site across provider networks





Rao, et al.              Expires August 13, 2021               [Page 12]


Internet-Draft          BGP CAR Problem Statement          February 2021


         +  Provide ability for a CE to select paths through specific
            PEs for a given intent

            -  Example-1: Certain intent in transport not available via
               specific PEs

            -  Example-2: Certain CE-PE connection does not support
               specific intent

            -  Example-3: Site access via certain CE does not support
               specific intent.  For instance, link connecting a
               specific CE to a DC hosting loss-sensitive service may
               have better quality than a link from another CE

         +  Provide ability for a CE to send traffic indicating a
            specific intent (via suitable encapsulation) to the PE for
            optimal steering.

      *  Intent aware routing support for multiple service (VPN)
         interworking models

         +  Beyond options such as iBGP or Inter-AS Option C that
            inherently extend from PE to PE

            1.  Inter-AS Option A

            2.  Inter-AS Option B

            3.  GW based interworking(L3VPN, EVPN)

         +  Interworking with existing L3VPN deployments, both PEs and
            CEs

   o  The network diagram below illustrates the reference network
      topology used in this section for VPN CAR.
















Rao, et al.              Expires August 13, 2021               [Page 13]


Internet-Draft          BGP CAR Problem Statement          February 2021


        +-------------------+           +-------------------+
        |   ....|S-RR|....  |           |  ....|S-RR|.....  |
        |   :   +----+   :  |           |  :   +----+    :  |
        |   :    :  :    :  |           |  :    :  :     :  |
        |----+   :  :   +---|   D=20    |---+   :  :   +----|
       /|PE11|   :  :   |121|-----------|211|   :  :   |PE21|\
 D=25/  |----+   :  :   +---| X       X |---+   :  :   +----|  \ D=25
   /    |        :  :       |   X   X   |       :  :        |    \   V/24
CE1     |        :  :       |     X D=50|       :  :        |     CE2<---
   X    |        :  :       |   X   X   |       :  :        |    X
D=15 X  |----+   :  :   +---| X       X |---+   :  :   +----|  X D=10
       X|PE12|...:  :...|212|-----------|232|...:  :...|PE22|X
        |----+          +---|   D=10    |---+          +----|
        |                   |           |                   |
        |     AS 1          |           |     AS 2          |
        +-------------------+           +-------------------+



                   Figure 5: VPN CAR reference topology

      The following network design assumptions apply to the reference
      topology above, as an example:

      *  Independent ISIS/OSPF SR instance in each AS.

      *  eBGP peering link between VPN ASBRs 121-211, 121-212, 122-211,
         122-212.

      *  VPN service is running between PEs via service RRs in each AS
         to local ASBRs.  Between ASBRs, its Option-B i.e. next hop self
         for VPN SAFI.

      *  CE1 is dual homed to PE11 and PE12.  Similarly, CE2 is dual
         homed to PE21 and PE22.

      *  Peering links have equal cost metric

      *  Peering links have delay configured or measured as shown by
         "D".

      *  CE2 advertises prefix V/24 to CE1.  It is advertised as RD:V/24
         between PEs, including color-awareness

   o  The following sections illustrate a few examples of intent use-
      cases applicable to VPN (service) routes.





Rao, et al.              Expires August 13, 2021               [Page 14]


Internet-Draft          BGP CAR Problem Statement          February 2021


3.2.1.  Use-case of minimization of a cost metric vs a latency metric

   o  In the reference topology of Figure 5

         Each AS has Flex Algo 0 and 128.

         Flex Algo 0 is for minimum cost metric(cost optimized).

         Flex Algo 128 definition is for minimum delay (low latency).

   o  Cost Optimized

      *  Color C1 - Minimum cost intent.

      *  On CE1, flows requiring cost optimized paths to V/24 are
         steered over (C1, V/24) route.

         +  BGP CAR for C1 sets up paths between CEs for minimum end-to-
            end cost.

         +  This advertisement needs BGP CAR between PE-CE for V/24
            prefix and color C1 awareness.

         +  It also needs BGP VPN CAR between PEs and ASBRs for RD:V/24
            prefix and color C1 awareness (C1, RD:V/24).

         +  Paths traverse over PE-CE links, intra-domain Flex Algo 0 in
            each AS and peering links between ASBRs, minimizing cost for
            VPN.

         +  Example: CE1 learns (C1, V/24) CAR route through several
            equal cost paths:

            1.  One path is through link CE1-PE11, FA0 to 121, link
                121-211, FA0 to PE21 and link PE21-CE2.

            2.  Another such path is through CE1-PE12, FA0 to node 122,
                link 122-212, FA0 to PE22, link PE22-CE2.

   o  Minimize latency

      *  Color C2 - Minimum latency intent

      *  On CE1, flows requiring low latency paths to prefix V/24 are
         steered over (C2, V/24) CAR route.

         +  BGP CAR for C2 sets up paths between CEs for minimum end-to-
            end delay.



Rao, et al.              Expires August 13, 2021               [Page 15]


Internet-Draft          BGP CAR Problem Statement          February 2021


         +  This advertisement needs BGP CAR between PE-CE for V/24
            prefix and color C2 awareness.

         +  It also needs BGP VPN CAR between PEs and ASBR for RD:V/24
            prefix and color C2 awareness (C2, RD:V/24).

         +  Paths traverse over intra-domain Flex Algo 128 in each AS
            and accounts for inter ASBR link delays and PE-CE link
            delays for the VPN.

         +  Example: CE1 learns (C2, V/24) CAR best route through link
            CE1-PE12, FA128 to 122, link 122-212, FA128 to PE22 and link
            PE22-CE2.

3.2.2.  Use-case of exclusion/inclusion of link affinity

   o  Color C3 - Intent to Minimize cost metric and avoid purple links

   o  In the reference topology of Figure 5

         Each AS has Flex Algo 129 and some links have purple affinity.

         Flex Algo 129 definition is set to minimum cost metric and
         avoid purple links (within AS).

         ASBR cross links are colored purple by policy.  Bottom PE-CE
         links are colored purple as well by policy

   o  On CE1, flows requiring minimum cost path avoiding purple links to
      V/24 are steered over (C3, V/24) BGP CAR route.

      *  BGP CAR for C3 setup paths between CEs for minimum end-to-end
         cost and avoiding purple link affinity.

      *  This advertisement needs BGP CAR between PE-CE for V/24 prefix
         and color C3 awareness

      *  It also needs BGP VPN CAR between PEs and ASBRs for RD:V/24
         prefix and color C3 awareness (C3, RD:V/24).

      *  The path avoids purple PE-CE links, traverses over intra-domain
         Flex Algo 129 in each AS and avoids purple links between VPN
         ASBRs.

      *  Example: CE1 learns (C3, V/24) CAR route through link CE1-PE11,
         FA129 to 121, link 121-211, FA129 to PE21 and link PE21-CE2.





Rao, et al.              Expires August 13, 2021               [Page 16]


Internet-Draft          BGP CAR Problem Statement          February 2021


3.2.3.  Use-case of virtual network function chains in local and core
        domains

                               +-----+
       ........................|S-RR | <.................
       :                       +-----+ <...........     :
       :                                           :    :
       :                                           :    :
       :  ___     ___           ___                :    :
       : /   \   /   \         /   \               :    :
       :| S1  | | S2  |       | S3  |              :    :
       : \   /   \   /         \   /               :    :
     +-:---------------+  +--------------+  +------:----:--+
     | :  |E11|  |E12| |  |    |E21|     |  |      :    :  |
     | :  +---+  +---+ |  |    +---+     |  |      :  +----|<-(V1/24,C1)
     | :               |  |              |  |      :  |PE31|--CE2
     | V               |  |              |  |      :  +----|
     |----+          +------+            +------+  :       |
CE1--|PE11|          | 121  |            | 231  |  :       |
     |----+          +------+            +------+  :  +----|<-(V2/24/C2)
     |                 |  |              |  |      :..|PE32|--CE3
     |                 |  |              |  |         +----|
     |                 |  |              |  |              |
     |                 |  |              |  |              |
     |    Domain 1     |  |   Domain 2   |  |   Domain 3   |
     +-----------------+  +--------------+  +--------------+



                                 Figure 6

   o  Color intent

      *  C1 - Routing via NFV service chain comprising of [S1, S2]
         attached to E11 and E12

      *  C2 - Routing via NFV service [S3] attached to E21

   o  CE1, CE2, CE3 are sites of VPN1.

   o  Prefix V1/24 colored with C1 from CE2, and advertised as RD:V1/24
      with C1 by PE31 to PE11 via S-RR

   o  Prefix V2/24 colored with C2 from CE3, and advertised as RD:V2/24
      with C2 by PE32 to PE11 via SS-RR

   o  From PE11:




Rao, et al.              Expires August 13, 2021               [Page 17]


Internet-Draft          BGP CAR Problem Statement          February 2021


      *  [V1/24, C1] mapped packets are sent via S1, S2 and then routed
         to PE31, CE2

      *  [V2/24, C2] mapped packets are sent via S3 and then routed to
         PE32, CE3

4.  Deployment Requirements

   o  Co-existence, compatibility and interworking with currently
      deployed SR-PCE based multi-domain color-aware solution

   o  Support different multi-domain deployment designs

      *  Multiple IGP domains within a single AS (Seamless MPLS)

         +  Inter-connect at node level (ABR)

      *  Multiple BGP AS domains

         +  Inter-connect via peering links (ASBR)

   o  Support end-to-end path crossing transport domains with different
      technologies and encapsulations

      *  LDP-MPLS

      *  RSVP-TE-MPLS

      *  SR-MPLS

      *  SRv6

      *  IPv4/IPv6

   o  Support interworking between domains with different encapsulations
      (e.g, SR-MPLS and SRv6)

   o  Support multiple transport encapsulations within a domain for co-
      existence and migration

   o  Provide a BGP-based control-plane solution for the use-case
      illustrated in [RFC8604] together with deployment design
      guidelines for the leverage of anycast and binding SIDs.








Rao, et al.              Expires August 13, 2021               [Page 18]


Internet-Draft          BGP CAR Problem Statement          February 2021


5.  Scalability

5.1.  Scale Requirements

   o  Support for massive scaled transport network

      *  Number of Remote PE's: >= 300k

      *  Number of Colors C: >= 5

   o  Scalable MPLS dataplane solution

      *  With one label per (C, Remote PE), the 1M MPLS dataplane does
         not work.

      *  A notion of hierarchy or segment list is required.

         +  E.g. the SR-PCE builds the end-to-end path as a list of
            segments such that no single node needs to support a data-
            plane scaling in the order of (Remote PE * C)

         +  The solution is thus not a direct extension of BGP-LU

      *  Additionally, PE and transit nodes (ABRs) may be devices with
         limited forwarding table space

      *  Devices may have constraints on packet processing (e.g., label
         operations, number of labels pushed) and performance

   o  Ability to abstract the topology from remote domains - for scale,
      stability and faster convergence

      *  Abstracting PE and/or ABR related state and network events

   o  Support for an Emulated-PULL model for the BGP signaling

      *  The SR-PCE solution natively supports a PULL model: when PE1
         installs a VPN route V/v via (C, PE2), PE1 requests its serving
         SR-PCE to compute the SR Policy to (C, PE2).  I.e.  PE1 does
         not learn unneeded SR policies.

      *  BGP Signaling is natively a PUSH model.

      *  Emulated-PULL refers to the ability for a BGP CAR node PE1 to
         "subscribe" to (C, PE2) route such that only the related paths
         are signaled to PE1.





Rao, et al.              Expires August 13, 2021               [Page 19]


Internet-Draft          BGP CAR Problem Statement          February 2021


      *  The subscription and related filtering solution must apply to
         any BGP CAR node

         +  Transport CAR routes

            1.  Ability for a node (PE/ABR/RR) to signal interest for
                routes of specific colors.

            2.  PEs only learn routes that they need - remote VPN
                endpoints (PEs/ASBRs) or transit nodes (ABRs, ASBRs).

            3.  ABRs also only learn and propagate routes they need
                locally in domain

         +  Service/VPN CAR routes

            1.  Ability for a node (PE) to signal interest for a
                specific (Egress PE, Color) transport route

            2.  CEs learn routes that they need - interested colors

            3.  PEs learn routes that they need - interested VPNs,
                colors

         +  Automation of the subscription/filter route

            1.  Similar to the SR-PCE solution, when an ingress PE1
                installs VPN V/v via (C, PE2), PE1 originates its
                subscription/filter route for (C, PE2).

         +  Efficient propagation and processing of subscription/filter
            routes.

         +  Ability to perform aggregation and suppression of
            subscription/filter routes at nodes in the route propagation
            path to reduce explosion and churn in propagation of the
            filter routes themselves.

         +  The solution may be optional for networks that do not have
            the large scaling requirements

5.2.  Scale Analysis

   It is useful to analyze the multiple scaling requirements and
   specifically the data plane constraints in the context of a few
   common reference designs and use-cases.

   A couple of example scenarios are listed below for reference.



Rao, et al.              Expires August 13, 2021               [Page 20]


Internet-Draft          BGP CAR Problem Statement          February 2021


   o  Seamless-MPLS design, with IGP Flex-Algo in each domain

                                    +-----+
     .............................. |S-RR | <........................
     :                              +-----+                         :
     :                                                              :
     :                                                              :
  +--:-----------------+  +--------------------+  +-----------------:--+
  |  :                 |  |                    |  |                 :  |
  |  :                 |  |                    |  |                 :  |
  |  :               +------+                +------+               :  |
  |  :               | 121  |                | 231  |               :  |
  |  V               +------+                +------+               :  |
  |----+               |  |                    |  |               +----|
  |PE11|               |  |                    |  |               |PE31|
  |----+               |  |                    |  |               +----|
  |                  +------+                +------+                  |
  |                  | 122  |                | 232  |                  |
  |                  +------+                +------+                  |
  |                    |  |                    |  |                    |
  |      Domain 1      |  |      Domain 2      |  |     Domain 3       |
  +--------------------+  +--------------------+  +--------------------+



                                 Figure 7

   o  Inter-AS Option C VPN design, with IGP Flex-Algo in each domain,
      and eBGP peering between domains






















Rao, et al.              Expires August 13, 2021               [Page 21]


Internet-Draft          BGP CAR Problem Statement          February 2021


        +-----+                +-----+                  +-----+
    ....|S-RR1| <............. |S-RR2| <............... |S-RR3| <...
    :   +-----+                +-----+                  +-----+     :
    :                                                               :
    :                                                               :
    :                                                               :
 +--:---------------+      +------------------+      +--------------:--+
 |  :               |      |                  |      |              :  |
 |  :               |      |                  |      |              :  |
 |  :           +---|      |---+          +---|      |---+          :  |
 |  :           |121|------|211|          |231|------|321|          :  |
 |  :           +---|      |---+          +---|      |---+          :  |
 |----+             |      |                  |      |            +----|
 |PE11|             |      |                  |      |            |PE31|
 |----+             |      |                  |      |            +----|
 |              +---|      |---+          +---|      |---+             |
 |              |122|------|212|          |232|------|322|             |
 |              +---|      |---+          +---|      |---+             |
 |                  |      |                  |      |                 |
 |    Domain 1      |      |    Domain 2      |      |    Domain 3     |
 +------------------+      +------------------+      +-----------------+



                                 Figure 8

6.  Network Availability

   o  The BGP CAR solution should provide high network availability for
      typical deployment topologies, with minimum loss of connectivity
      in different network failure scenarios.

   o  The network failure scenarios, applicable technologies and design
      options described in [I-D.ietf-mpls-seamless-mpls] should be used
      as a reference.

   o  In the Seamless-MPLS reference topology in previous section:

      *  Failure of intra-domain links should limit loss of connectivity
         (LoC) to < 50ms.  E.g., PE11 to a P node (not shown), 121 to a
         P node in Domain1 or Domain2)

      *  Failure of an intra-domain node (P node in any domain) should
         limit LoC to < 50ms

      *  Failure of an ABR node (e.g., 121, 231) should limit LoC to <
         1sec




Rao, et al.              Expires August 13, 2021               [Page 22]


Internet-Draft          BGP CAR Problem Statement          February 2021


      *  Failure of a remote PE node (e.g., PE3) should limit LoC to <
         1sec

   o  In the Inter-AS Option C VPN reference topology in previous
      section:

      *  Failure of intra-domain links should limit LoC to < 50ms.
         E.g., PE11 to a P node (not shown), 121 to a P node in Domain1
         or Domain2)

      *  Failure of an intra-domain node (P node in any domain) should
         limit LoC to < 50ms

      *  Failure of an ASBR node (e.g., 121, 211) should limit LoC to <
         1sec

      *  Failure of a remote PE node (e.g., PE3) should limit LoC to <
         1sec

      *  Failure of an external link (e.g., 121-211) should limit LoC to
         < 1sec

   o  The solution should explore and describe additional techniques and
      design options that are applicable to further improve handling of
      the failure cases listed above.

7.  BGP Protocol Requirements

   o  Support signaling and distribution of different Color-Aware routes
      to reach a participating node, e.g., a PE.  Intent should be
      indicated by the notion of a Color as defined in SR Policy
      Architecture.

      *  Signal different instances of a prefix distinguished by color

      *  Signal intent associated with a given route

   o  Support for a flexible NLRI definition to accommodate both
      efficiency of processing (e.g., packing) and future extensibility

      *  Avoid limitations associated with existing SAFI NLRI
         definitions.  For example, 24-bit label.

   o  Support for validation of paths

      *  Reachability of next-hop in control plane

      *  Availability and programming of encapsulation in data plane



Rao, et al.              Expires August 13, 2021               [Page 23]


Internet-Draft          BGP CAR Problem Statement          February 2021


      *  Validation of intent

   o  Next-hop resolution for Color-Aware route

      *  Flexibility to use different intra-domain and inter-domain
         mechanisms - IGP-FA, SR-TE, RSVP-TE, IGP, BGP-LU etc.

      *  Recursive resolution over BGP Color-Aware routes

      *  Ability to carry end-to-end cumulative metric for a given color

      *  Support setting up an end-to-end Color-Aware path using a
         different/less preferred or best-effort paths in domains where
         a particular intent is not available

   o  Separation of transport and VPN service semantics.

      *  Allow for different route distribution planes for service vs
         transport routes.

   o  Support signaling of different transport encapsulations

   o  Support for signaling multiple encapsulations for co-existence and
      migration

   o  Generation of BGP Color-Aware routes sourced from IGP-FA, SR-TE
      policies and BGP-LU from a domain

   o  Support signaling across domains with different color mappings for
      a given intent.

8.  Future Considerations

   Multicast service intent

9.  Acknowledgements

   Many people contributed to this document.

   The authors would especially like to thank Jim Uttaro for his
   guidance on the work and feedback on many aspects of the problem
   statement.  We would also like to thank Daniel Voyer, Luay Jalil and
   Robert Raszuk for their review and valuable suggestions.

   We also express our appreciation to Bruno Decreane, Keyur Patel, Jim
   Guichard, Alex Bogdanov, Dirk Steinberg, Hannes Gredler and Xiaohu Hu
   for discussions on several topics that have helped provide input to
   the document.



Rao, et al.              Expires August 13, 2021               [Page 24]


Internet-Draft          BGP CAR Problem Statement          February 2021


   The authors would like to thank Stephane Litkowski for his detailed
   review and for making valuable suggestions to improve the quality of
   the document.  We would also like to thank Kamran Raza and Kris
   Michelson for their review and comments on the document and to Simon
   Spraggs, Jose Liste and Jiri Chaloupka for their early inputs on the
   problem statement.

10.  References

10.1.  Normative References

   [I-D.agrawal-spring-srv6-mpls-interworking]
              Agrawal, S., Ali, Z., Filsfils, C., Voyer, D., and Z. Li,
              "SRv6 and MPLS interworking", draft-agrawal-spring-srv6-
              mpls-interworking-03 (work in progress), August 2020.

   [I-D.ietf-bess-srv6-services]
              Dawra, G., Filsfils, C., Talaulikar, K., Raszuk, R.,
              Decraene, B., Zhuang, S., and J. Rabadan, "SRv6 BGP based
              Overlay services", draft-ietf-bess-srv6-services-05 (work
              in progress), November 2020.

   [I-D.ietf-idr-bgp-ipv6-rt-constrain]
              Patel, K., Raszuk, R., Djernaes, M., Dong, J., and M.
              Chen, "IPv6 Extensions for Route Target Distribution",
              draft-ietf-idr-bgp-ipv6-rt-constrain-12 (work in
              progress), April 2018.

   [I-D.ietf-idr-tunnel-encaps]
              Patel, K., Velde, G., Sangli, S., and J. Scudder, "The BGP
              Tunnel Encapsulation Attribute", draft-ietf-idr-tunnel-
              encaps-21 (work in progress), January 2021.

   [I-D.ietf-lsr-flex-algo]
              Psenak, P., Hegde, S., Filsfils, C., Talaulikar, K., and
              A. Gulko, "IGP Flexible Algorithm", draft-ietf-lsr-flex-
              algo-13 (work in progress), October 2020.

   [I-D.ietf-spring-segment-routing-policy]
              Filsfils, C., Talaulikar, K., Voyer, D., Bogdanov, A., and
              P. Mattes, "Segment Routing Policy Architecture", draft-
              ietf-spring-segment-routing-policy-09 (work in progress),
              November 2020.








Rao, et al.              Expires August 13, 2021               [Page 25]


Internet-Draft          BGP CAR Problem Statement          February 2021


   [I-D.ietf-spring-sr-service-programming]
              Clad, F., Xu, X., Filsfils, C., daniel.bernier@bell.ca,
              d., Li, C., Decraene, B., Ma, S., Yadlapalli, C.,
              Henderickx, W., and S. Salsano, "Service Programming with
              Segment Routing", draft-ietf-spring-sr-service-
              programming-03 (work in progress), September 2020.

   [I-D.ietf-spring-srv6-network-programming]
              Filsfils, C., Camarillo, P., Leddy, J., Voyer, D.,
              Matsushima, S., and Z. Li, "SRv6 Network Programming",
              draft-ietf-spring-srv6-network-programming-28 (work in
              progress), December 2020.

   [I-D.voyer-pim-sr-p2mp-policy]
              Voyer, D., Filsfils, C., Parekh, R., Bidgoli, H., and Z.
              Zhang, "Segment Routing Point-to-Multipoint Policy",
              draft-voyer-pim-sr-p2mp-policy-02 (work in progress), July
              2020.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC4360]  Sangli, S., Tappan, D., and Y. Rekhter, "BGP Extended
              Communities Attribute", RFC 4360, DOI 10.17487/RFC4360,
              February 2006, <https://www.rfc-editor.org/info/rfc4360>.

   [RFC4684]  Marques, P., Bonica, R., Fang, L., Martini, L., Raszuk,
              R., Patel, K., and J. Guichard, "Constrained Route
              Distribution for Border Gateway Protocol/MultiProtocol
              Label Switching (BGP/MPLS) Internet Protocol (IP) Virtual
              Private Networks (VPNs)", RFC 4684, DOI 10.17487/RFC4684,
              November 2006, <https://www.rfc-editor.org/info/rfc4684>.

   [RFC4760]  Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
              "Multiprotocol Extensions for BGP-4", RFC 4760,
              DOI 10.17487/RFC4760, January 2007,
              <https://www.rfc-editor.org/info/rfc4760>.

   [RFC5512]  Mohapatra, P. and E. Rosen, "The BGP Encapsulation
              Subsequent Address Family Identifier (SAFI) and the BGP
              Tunnel Encapsulation Attribute", RFC 5512,
              DOI 10.17487/RFC5512, April 2009,
              <https://www.rfc-editor.org/info/rfc5512>.






Rao, et al.              Expires August 13, 2021               [Page 26]


Internet-Draft          BGP CAR Problem Statement          February 2021


   [RFC5701]  Rekhter, Y., "IPv6 Address Specific BGP Extended Community
              Attribute", RFC 5701, DOI 10.17487/RFC5701, November 2009,
              <https://www.rfc-editor.org/info/rfc5701>.

   [RFC7311]  Mohapatra, P., Fernando, R., Rosen, E., and J. Uttaro,
              "The Accumulated IGP Metric Attribute for BGP", RFC 7311,
              DOI 10.17487/RFC7311, August 2014,
              <https://www.rfc-editor.org/info/rfc7311>.

   [RFC7606]  Chen, E., Ed., Scudder, J., Ed., Mohapatra, P., and K.
              Patel, "Revised Error Handling for BGP UPDATE Messages",
              RFC 7606, DOI 10.17487/RFC7606, August 2015,
              <https://www.rfc-editor.org/info/rfc7606>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8277]  Rosen, E., "Using BGP to Bind MPLS Labels to Address
              Prefixes", RFC 8277, DOI 10.17487/RFC8277, October 2017,
              <https://www.rfc-editor.org/info/rfc8277>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

   [RFC8664]  Sivabalan, S., Filsfils, C., Tantsura, J., Henderickx, W.,
              and J. Hardwick, "Path Computation Element Communication
              Protocol (PCEP) Extensions for Segment Routing", RFC 8664,
              DOI 10.17487/RFC8664, December 2019,
              <https://www.rfc-editor.org/info/rfc8664>.

   [RFC8669]  Previdi, S., Filsfils, C., Lindem, A., Ed., Sreekantiah,
              A., and H. Gredler, "Segment Routing Prefix Segment
              Identifier Extensions for BGP", RFC 8669,
              DOI 10.17487/RFC8669, December 2019,
              <https://www.rfc-editor.org/info/rfc8669>.








Rao, et al.              Expires August 13, 2021               [Page 27]


Internet-Draft          BGP CAR Problem Statement          February 2021


10.2.  Informative References

   [I-D.filsfils-spring-sr-policy-considerations]
              Filsfils, C., Talaulikar, K., Krol, P., Horneffer, M., and
              P. Mattes, "SR Policy Implementation and Deployment
              Considerations", draft-filsfils-spring-sr-policy-
              considerations-06 (work in progress), October 2020.

   [I-D.ietf-idr-performance-routing]
              Xu, X., Hegde, S., Talaulikar, K., Boucadair, M., and C.
              Jacquenet, "Performance-based BGP Routing Mechanism",
              draft-ietf-idr-performance-routing-03 (work in progress),
              December 2020.

   [I-D.ietf-mpls-seamless-mpls]
              Leymann, N., Decraene, B., Filsfils, C., Konstantynowicz,
              M., and D. Steinberg, "Seamless MPLS Architecture", draft-
              ietf-mpls-seamless-mpls-07 (work in progress), June 2014.

   [RFC3906]  Shen, N. and H. Smit, "Calculating Interior Gateway
              Protocol (IGP) Routes Over Traffic Engineering Tunnels",
              RFC 3906, DOI 10.17487/RFC3906, October 2004,
              <https://www.rfc-editor.org/info/rfc3906>.

   [RFC4271]  Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
              Border Gateway Protocol 4 (BGP-4)", RFC 4271,
              DOI 10.17487/RFC4271, January 2006,
              <https://www.rfc-editor.org/info/rfc4271>.

   [RFC4272]  Murphy, S., "BGP Security Vulnerabilities Analysis",
              RFC 4272, DOI 10.17487/RFC4272, January 2006,
              <https://www.rfc-editor.org/info/rfc4272>.

   [RFC4364]  Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
              Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
              2006, <https://www.rfc-editor.org/info/rfc4364>.

   [RFC6952]  Jethanandani, M., Patel, K., and L. Zheng, "Analysis of
              BGP, LDP, PCEP, and MSDP Issues According to the Keying
              and Authentication for Routing Protocols (KARP) Design
              Guide", RFC 6952, DOI 10.17487/RFC6952, May 2013,
              <https://www.rfc-editor.org/info/rfc6952>.

   [RFC7911]  Walton, D., Retana, A., Chen, E., and J. Scudder,
              "Advertisement of Multiple Paths in BGP", RFC 7911,
              DOI 10.17487/RFC7911, July 2016,
              <https://www.rfc-editor.org/info/rfc7911>.




Rao, et al.              Expires August 13, 2021               [Page 28]


Internet-Draft          BGP CAR Problem Statement          February 2021


Authors' Addresses

   Dhananjaya Rao
   Cisco Systems
   USA

   Email: dhrao@cisco.com


   Swadesh Agrawal
   Cisco Systems
   USA

   Email: swaagraw@cisco.com


   Clarence Filsfils
   Cisco Systems
   Belgium

   Email: cfilsfil@cisco.com


   Ketan Talaulikar
   Cisco Systems
   India

   Email: ketant@cisco.com























Rao, et al.              Expires August 13, 2021               [Page 29]