Network Working Group                                         A. Bierman
Internet-Draft                                                 YumaWorks
Intended status: Standards Track                            M. Bjorklund
Expires: April 21, 2016                                   Tail-f Systems
                                                                 J. Dong
                                                     Huawei Technologies
                                                            D. Romascanu
                                                                   Avaya
                                                        October 19, 2015


                 A YANG Data Model for Entity Managemet
                    draft-entitydt-netmod-entity-00

Abstract

   This document defines a YANG data model for the management of
   multiple physical entities managed by a single server.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 21, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of



Bierman, et al.          Expires April 21, 2016                 [Page 1]


Internet-Draft           YANG Entity Management             October 2015


   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   2
       1.1.1.  Tree Diagrams . . . . . . . . . . . . . . . . . . . .   2
   2.  Objectives  . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Entity Data Model . . . . . . . . . . . . . . . . . . . . . .   3
     3.1.  The Physical Entry Lists  . . . . . . . . . . . . . . . .   5
   4.  Relationship to ENTITY-MIB  . . . . . . . . . . . . . . . . .   5
   5.  Relationship to ENTITY-SENSOR-MIB . . . . . . . . . . . . . .   6
   6.  Relationship to ENTITY-STATE-MIB  . . . . . . . . . . . . . .   6
   7.  Entity YANG Module  . . . . . . . . . . . . . . . . . . . . .   6
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  34
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .  35
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  35
   11. Normative References  . . . . . . . . . . . . . . . . . . . .  35
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  35

1.  Introduction

   This document defines a YANG data model for the management of
   multiple physical entities managed by a single server.

   The data model includes configuration data and state data (status
   information and counters for the collection of statistics).

1.1.  Terminology

   The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14, [RFC2119].

1.1.1.  Tree Diagrams

   A simplified graphical representation of the data model is used in
   this document.  The meaning of the symbols in these diagrams is as
   follows:

   o  Brackets "[" and "]" enclose list keys.

   o  Abbreviations before data node names: "rw" means configuration
      data (read-write) and "ro" state data (read-only).





Bierman, et al.          Expires April 21, 2016                 [Page 2]


Internet-Draft           YANG Entity Management             October 2015


   o  Symbols after data node names: "?" means an optional node, "!"
      means a presence container, and "*" denotes a list and leaf-list.

   o  Parentheses enclose choice and case nodes, and case nodes are also
      marked with a colon (":").

   o  Ellipsis ("...") stands for contents of subtrees that are not
      shown.

2.  Objectives

   This section describes some of the design objectives for the entity
   model.

   o  There are many common properties used to identify the entities,
      which need to be supported in the entity data module.

   o  There are many important information and states about the
      entities, which needs to be collected from the devices which
      support the entity data model.

   o  The entity data model SHOULD be suitable for new implementations
      to use as is.

   o  The entity data model defined in this document can be implemented
      on a system that also implements ENTITY-MIB, thus the mapping
      between the entity data model and ENTITY-MIB SHOULD be clear.

3.  Entity Data Model

   This document defines the YANG module "ietf-entity", which has the
   following structure:

     module: ietf-entity
        +--ro entity-state
        |  +--ro last-change?       yang:date-and-time
        |  +--ro physical-entity* [name]
        |     +--ro name                  string
        |     +--ro class?                identityref
        |     +--ro physical-index?       int32 {entity-mib}?
        |     +--ro description?          string
        |     +--ro contained-in*         -> ../../physical-entity/name
        |     +--ro contains-child*       -> ../../physical-entity/name
        |     +--ro parent-rel-pos?       int32
        |     +--ro hardware-rev?         string
        |     +--ro firmware-rev?         string
        |     +--ro software-rev?         string
        |     +--ro serial-num?           string



Bierman, et al.          Expires April 21, 2016                 [Page 3]


Internet-Draft           YANG Entity Management             October 2015


        |     +--ro mfg-name?             string
        |     +--ro model-name?           string
        |     +--ro alias?                string
        |     +--ro asset-id?             string
        |     +--ro is-fru?               boolean
        |     +--ro mfg-date?             yang:date-and-time
        |     +--ro uri*                  inet:uri
        |     +--ro uuid?                 yang:uuid
        |     +--ro state {entity-state}?
        |     |  +--ro state-last-changed?     yang:date-and-time
        |     |  +--ro admin-state?            entity-admin-state
        |     |  +--ro oper-state?             entity-oper-state
        |     |  +--ro usage-state?            entity-usage-state
        |     |  +--ro alarm-status?           entity-alarm-status
        |     |  +--ro standby-status?         entity-standby-status
        |     +--ro sensor-data {entity-sensor}?
        |        +--ro data-type?              entity-sensor-data-type
        |        +--ro data-scale?             entity-sensor-data-scale
        |        +--ro precision?              entity-sensor-precision
        |        +--ro value?                  entity-sensor-value
        |        +--ro oper-status?            entity-sensor-status
        |        +--ro sensor-units-display?   string
        |        +--ro value-timestamp?        yang:date-and-time
        |        +--ro value-update-rate?      uint32
        +--rw entity {entity-config}?
           +--rw physical-entity* [name]
              +--rw name           string
              +--rw serial-num?    string
              +--rw alias?         string
              +--rw asset-id?      string
              +--rw uri*           inet:uri
              +--rw admin-state?   entity-admin-state {entity-state}?

     notifications:
        +---n ent-config-change
        +---n ent-state-oper-enabled {entity-state}?
        |  +--ro name?           -> /entity-state/physical-entity
                                    /name
        |  +--ro admin-state?    -> /entity-state/physical-entity
                                    /state/admin-state
        |  +--ro alarm-status?   -> /entity-state/physical-entity
                                    /state/alarm-status
        +---n ent-state-oper-disabled {entity-state}?
           +--ro name?           -> /entity-state/physical-entity
                                    /name
           +--ro admin-state?    -> /entity-state/physical-entity
                                    /state/admin-state
           +--ro alarm-status?   -> /entity-state/physical-entity



Bierman, et al.          Expires April 21, 2016                 [Page 4]


Internet-Draft           YANG Entity Management             October 2015


                                    /state/alarm-status

3.1.  The Physical Entry Lists

   The data model for physical entities presented in this document uses
   a flat list of entities.  Each entity in the list is identified by
   its name.  Furthermore, each entity has a mandatory "class" leaf.

   The "iana-entity" module defines YANG identities for the hardware
   types in the IANA-maintained "IANA-ENTITY-MIB" registry.

   The "class" leaf is a YANG identity that describes the type of the
   hardware.  Vendors are encouraged to either directly use one of the
   common IANA-defined identities, or derive a more specific identity
   from one of them.

   There is one optional list of configured physical entities ("/entity/
   physical-entity"), and a separate list for the operational state of
   all physical entities ("/entity-state/physical-entity").

4.  Relationship to ENTITY-MIB

   If the device implements the ENTITY-MIB [RFC6933], each entry in the
   /entity-state/physical-entity list is mapped to one EntPhysicalEntry.
   Objects that are writable in the MIB are mapped to nodes in the
   /entity/physical-entity list.

   The "physical-index" leaf MUST contain the value of the corresponding
   entPhysicalEntry's entPhysicalIndex.

   The "class" leaf is mapped to both entPhysicalClass and
   entPhysicalVendorType.  If the value of the "class" leaf is an
   identity that is either derived from or is one of the identities in
   the "iana-entity" module, then entPhysicalClass contains the
   corresponding IANAPhysicalClass enumeration value.  Otherwise,
   entPhysicalClass contains the IANAPhysicalClass value "other(1)".
   Vendors are encouraged to define an identity (derived from an
   identity in "iana-entity" if possible) for each enterprise-specific
   registration identifier used for entPhysicalVendorType, and use that
   identity for the "class" leaf.

   The following tables list the YANG data nodes with corresponding
   objects in the ENTITY-MIB.








Bierman, et al.          Expires April 21, 2016                 [Page 5]


Internet-Draft           YANG Entity Management             October 2015


   +------------------------------------+------------------------------+
   | YANG data node in /entity-state    | ENTITY-MIB object            |
   | /physical-entity                   |                              |
   +------------------------------------+------------------------------+
   | name                               | entPhysicalName              |
   | class                              | entPhysicalClass             |
   |                                    | entPhysicalVendorType        |
   | physical-index                     | entPhysicalIndex             |
   | description                        | entPhysicalDescr             |
   | contained-in                       | entPhysicalContainedIn       |
   | contains-child                     | entPhysicalChildIndex        |
   | parent-rel-pos                     | entPhysicalParentRelPos      |
   | hardware-rev                       | entPhysicalHardwareRev       |
   | firmware-rev                       | entPhysicalFirmwareRev       |
   | software-rev                       | entPhysicalSoftwareRev       |
   | serial-num                         | entPhysicalSerialNum         |
   | mfg-name                           | entPhysicalMfgName           |
   | model-name                         | entPhysicalModelName         |
   | alias                              | entPhysicalAlias             |
   | asset-id                           | entPhysicalAssetID           |
   | is-fru                             | entPhysicalIsFRU             |
   | mfg-date                           | entPhysicalMfgDate           |
   | uri                                | entPhysicalUris              |
   | uuid                               | entPhysicalUUID              |
   +------------------------------------+------------------------------+

              YANG data nodes and related ENTITY-MIB objects

5.  Relationship to ENTITY-SENSOR-MIB

   TBD relationship to [RFC3433].

6.  Relationship to ENTITY-STATE-MIB

   TBD relationship to [RFC4268].

7.  Entity YANG Module

   <CODE BEGINS> file "ietf-entity@2015-10-19.yang"

module ietf-entity {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-entity";
  prefix ent;

  import ietf-inet-types {
    prefix inet;
  }



Bierman, et al.          Expires April 21, 2016                 [Page 6]


Internet-Draft           YANG Entity Management             October 2015


  import ietf-yang-types {
    prefix yang;
  }

  organization
    "IETF NETMOD (NETCONF Data Modeling Language) Working Group";

  contact
    "WG Web:   <http://tools.ietf.org/wg/netmod/>
     WG List:  <mailto:netmod@ietf.org>

     WG Chair: Thomas Nadeau
               <mailto:tnadeau@lucidvision.com>

     WG Chair: Juergen Schoenwaelder
               <mailto:j.schoenwaelder@jacobs-university.de>

     WG Chair: Kent Watsen
               <mailto:kwatsen@juniper.net>

     Editor:   Andy Bierman
               <mailto:andy@yumaworks.com>

     Editor:   Martin Bjorklund
               <mailto:mbj@tail-f.com>

     Editor:   ";

  // RFC Ed.: replace XXXX with actual RFC number and remove this
  // note.

  description
    "This module contains a collection of YANG definitions for
     managing physical entities.

     Copyright (c) 2015 IETF Trust and the persons identified as
     authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (http://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC XXXX; see
     the RFC itself for full legal notices.";




Bierman, et al.          Expires April 21, 2016                 [Page 7]


Internet-Draft           YANG Entity Management             October 2015


  // RFC Ed.: update the date below with the date of RFC publication
  // and remove this note.
  revision 2015-10-19 {
    description
      "Initial revision.";
    reference
      "RFC XXXX: A YANG Data Model for Entity Managemet";
  }

  /*
   * Features
   */

  feature entity-mib {
    description
      "This feature indicates that the device implements
       the ENTITY-MIB.";
    reference "RFC 6933: Entity MIB (Version 4)";
  }

  feature entity-config {
    description
      "Indicates that the server supports configuration of
       physical entities.";
  }

  feature entity-state {
    description
      "Indicates the ENTITY-STATE-MIB objects are supported";
    reference "RFC 4268: Entity State MIB";
  }

  feature entity-sensor {
    description
      "Indicates the ENTITY-SENSOR-MIB objects are supported";
    reference "RFC 3433: Entity Sensor MIB";
  }

  /*
   * Typedefs
   */

  typedef entity-admin-state {
    type enumeration {
      enum unknown {
        value 1;
        description
          "The resource is unable to report administrative state.";



Bierman, et al.          Expires April 21, 2016                 [Page 8]


Internet-Draft           YANG Entity Management             October 2015


      }
      enum locked {
        value 2;
        description
          "The resource is administratively prohibited from use.";
      }
      enum shutting-down {
        value 3;
        description
          "The resource usage is administratively limited to current
           instances of use.";
      }
      enum unlocked {
        value 4;
        description
          "The resource is not administratively prohibited from use.";
      }
    }
    description
      "Represents the various possible administrative states.";
    reference "RFC 4268: EntityAdminState";
  }

  typedef entity-oper-state {
    type enumeration {
      enum unknown {
        value 1;
        description
          "The resource is unable to report operational state.";
      }
      enum disabled {
        value 2;
        description
          "The resource is totally inoperable.";
      }
      enum enabled {
        value 3;
        description
          "The resource is partially or fully operable.";
      }
      enum testing {
        value 4;
        description
          "The resource is currently being tested and cannot
           therefore report whether it is operational or not.";
      }
    }
    description



Bierman, et al.          Expires April 21, 2016                 [Page 9]


Internet-Draft           YANG Entity Management             October 2015


      "Represents the possible values of operational states.";
    reference "RFC 4268: EntityOperState";
  }

  typedef entity-usage-state {
    type enumeration {
      enum unknown {
        value 1;
        description
          "The resource is unable to report usage state.";
      }
      enum idle {
        value 2;
        description
          "The resource is servicing no users.";
      }
      enum active {
        value 3;
        description
          "The resource is currently in use and it has sufficient
           spare capacity to provide for additional users.";
      }
      enum busy {
        value 4;
        description
          "The resource is currently in use, but it currently has
           no spare capacity to provide for additional users.";
      }
    }
    description
      "Represents the possible values of usage states.";
    reference "RFC 4268, EntityUsageState";
  }

  typedef entity-alarm-status {
    type bits {
      bit unknown {
        position 0;
        description
          "The resource is unable to report alarm state.";
      }
      bit under-repair {
        position 1;
        description
          "The resource is currently being repaired, which, depending
           on the implementation, may make the other values in this
           bit string not meaningful.";
      }



Bierman, et al.          Expires April 21, 2016                [Page 10]


Internet-Draft           YANG Entity Management             October 2015


      bit critical {
        position 2;
        description
          "One or more critical alarms are active against the
           resource.";
      }
      bit major {
        position 3;
        description
          "One or more major alarms are active against the resource.";
      }
      bit minor {
        position 4;
        description
          "One or more minor alarms are active against the resource.";
      }
      bit warning {
        position 5;
        description
          "One or more warning alarms are active against the resource.
           This alarm status is not defined in X.733.";
      }
      bit indeterminate {
        position 6;
        description
          "One or more alarms of whose perceived severity cannot be
           determined are active against this resource.
           This alarm status is not defined in X.733.";
      }
    }
    description
      "Represents the possible values of alarm status.
       An Alarm [RFC3877] is a persistent indication of an error or
       warning condition.

       When no bits of this attribute are set, then no active
       alarms are known against this entity and it is not under
       repair.";
    reference "RFC 4268: EntityAlarmStatus";
  }

  typedef entity-standby-status {
    type enumeration {
      enum unknown {
        value 1;
        description
          "The resource is unable to report standby state.";
      }



Bierman, et al.          Expires April 21, 2016                [Page 11]


Internet-Draft           YANG Entity Management             October 2015


      enum hot-standby {
        value 2;
        description
          "The resource is not providing service, but it will be
           immediately able to take over the role of the resource
           to be backed up, without the need for initialization
           activity, and will contain the same information as the
           resource to be backed up.";
      }
      enum cold-standby {
        value 3;
        description
          "The resource is to back up another resource, but will not
           be immediately able to take over the role of a resource
           to be backed up, and will require some initialization
           activity.";
      }
      enum providing-service {
        value 4;
        description
          "The resource is providing service.";
      }
    }
    description
      "Represents the possible values of standby status.";
    reference "RFC 4268: EntityStandbyStatus";
  }

  typedef entity-sensor-data-type {
    type enumeration {
      enum other {
        value 1;
        description
          "A measure other than those listed below.";
      }
      enum unknown {
        value 2;
        description
          "An unknown measurement, or arbitrary, relative numbers";
      }
      enum volts-AC {
        value 3;
        description
          "A measure of electric potential (alternating current).";
      }
      enum volts-DC {
        value 4;
        description



Bierman, et al.          Expires April 21, 2016                [Page 12]


Internet-Draft           YANG Entity Management             October 2015


          "A measure of electric potential (direct current).";
      }
      enum amperes {
        value 5;
        description
          "A measure of electric current.";
      }
      enum watts {
        value 6;
        description
          "A measure of power.";
      }
      enum hertz {
        value 7;
        description
          "A measure of frequency.";
      }
      enum celsius {
        value 8;
        description
          "A measure of temperature.";
      }
      enum percent-RH {
        value 9;
        description
          "A measure of percent relative humidity.";
      }
      enum rpm {
        value 10;
        description
          "A measure of shaft revolutions per minute.";
      }
      enum cmm {
        value 11;
        description
          "A measure of cubic meters per minute (airflow).";
      }
      enum truth-value {
        value 12;
        description
          "Value is one of 1 (true) or 2 (false)";
      }
    }
    description
      "An node using this data type represents the Entity Sensor
       measurement data type associated with a physical sensor
       value. The actual data units are determined by examining an
       node of this type together with the associated



Bierman, et al.          Expires April 21, 2016                [Page 13]


Internet-Draft           YANG Entity Management             October 2015


       entity-sensor-data-scale node.

       An node of this type SHOULD be defined together with nodes
       of type entity-sensor-data-scale and
       entity-sensor-precision. These three types are used to identify
       the semantics of an node of type entity-sensor-value.";
    reference "RFC 3433: EntitySensorDataType";
  }

  typedef entity-sensor-data-scale {
    type enumeration {
      enum yocto {
        value 1;
        description
          "Data scaling factor of 10^-24.";
      }
      enum zepto {
        value 2;
        description
          "Data scaling factor of 10^-21.";
      }
      enum atto {
        value 3;
        description
          "Data scaling factor of 10^-18.";
      }
      enum femto {
        value 4;
        description
          "Data scaling factor of 10^-15.";
      }
      enum pico {
        value 5;
        description
          "Data scaling factor of 10^-12.";
      }
      enum nano {
        value 6;
        description
          "Data scaling factor of 10^-9.";
      }
      enum micro {
        value 7;
        description
          "Data scaling factor of 10^-6.";
      }
      enum milli {
        value 8;



Bierman, et al.          Expires April 21, 2016                [Page 14]


Internet-Draft           YANG Entity Management             October 2015


        description
          "Data scaling factor of 10^-3.";
      }
      enum units {
        value 9;
        description
          "Data scaling factor of 10^0.";
      }
      enum kilo {
        value 10;
        description
          "Data scaling factor of 10^3.";
      }
      enum mega {
        value 11;
        description
          "Data scaling factor of 10^6.";
      }
      enum giga {
        value 12;
        description
          "Data scaling factor of 10^9.";
      }
      enum tera {
        value 13;
        description
          "Data scaling factor of 10^12.";
      }
      enum exa {
        value 14;
        description
          "Data scaling factor of 10^15.";
      }
      enum peta {
        value 15;
        description
          "Data scaling factor of 10^18.";
      }
      enum zetta {
        value 16;
        description
          "Data scaling factor of 10^21.";
      }
      enum yotta {
        value 17;
        description
          "Data scaling factor of 10^24.";
      }



Bierman, et al.          Expires April 21, 2016                [Page 15]


Internet-Draft           YANG Entity Management             October 2015


    }
    description
      "An node using this data type represents a data scaling
       factor, represented with an International System of Units (SI)
       prefix.  The actual data units are determined by examining an
       node of this type together with the associated
       entity-sensor-data-type.

       An node of this type SHOULD be defined together with nodes
       of type entity-sensor-data-type and entity-sensor-precision.
       Together, associated nodes of these three types are used to
       identify the semantics of an node of type
       entity-sensor-value.";
    reference "RFC 3433: EntitySensorDataScale";
  }

  typedef entity-sensor-precision {
    type int32 {
      range "-8 .. 9";
    }
    description
      "An node using this data type represents a sensor
       precision range.

       An node of this type SHOULD be defined together with nodes
       of type entity-sensor-data-type and entity-sensor-data-scale.
       Together, associated nodes of these three types are used to
       identify the semantics of an node of type
       entity-sensor-value.

       If an node of this type contains a value in the range 1 to 9,
       it represents the number of decimal places in the fractional
       part of an associated entity-sensor-value fixed- point number.

       If an node of this type contains a value in the range -8 to
       -1, it represents the number of accurate digits in the
       associated entity-sensor-value fixed-point number.

       The value zero indicates the associated entity-sensor-value
       node is not a fixed-point number.

       Server implementors must choose a value for the associated
       entity-sensor-precision node so that the precision and
       accuracy of the associated entity-sensor-value node is
       correctly indicated.

       For example, a physical entity representing a temperature
       sensor that can measure 0 degrees to 100 degrees C in 0.1



Bierman, et al.          Expires April 21, 2016                [Page 16]


Internet-Draft           YANG Entity Management             October 2015


       degree increments, +/- 0.05 degrees, would have an
       entity-sensor-precision value of '1', an
       entity-sensor-data-scale value of 'units', and an
       entity-sensor-value ranging from '0' to '1000'.  The
       entity-sensor-value would be interpreted as 'degrees C * 10'.";
    reference "RFC 3433: EntitySensorPrecision";
  }

  typedef entity-sensor-value {
    type int32 {
      range "-1000000000 .. 1000000000";
    }
    description
     "An node using this data type represents an Entity Sensor
      value.

      An node of this type SHOULD be defined together with nodes
      of type entity-sensor-data-type, entity-sensor-data-scale, and
      entity-sensor-precision.  Together, associated nodes of those
      three types are used to identify the semantics of an node of
      this data type.

      The semantics of an node using this data type are determined
      by the value of the associated entity-sensor-data-type node.

      If the associated entity-sensor-data-type node is equal to
      'voltsAC', 'voltsDC', 'amperes', 'watts', 'hertz',
      'celsius', or 'cmm', then an node of this type MUST
      contain a fixed point number ranging from -999,999,999 to
      +999,999,999.  The value -1000000000 indicates an underflow
      error. The value +1000000000 indicates an overflow error.  The
      entity-sensor-precision indicates how many fractional digits are
      represented in the associated entity-sensor-value node.

      If the associated entity-sensor-data-type node is equal to
      'percentRH', then an node of this type MUST contain a
      number ranging from 0 to 100.

      If the associated entity-sensor-data-type node is equal to
      'rpm', then an node of this type MUST contain a number
      ranging from -999,999,999 to +999,999,999.

      If the associated entity-sensor-data-type node is equal to
      'truthvalue', then an node of this type MUST contain
      either the value 1 (true) or the value 2 (false)'.

      If the associated entity-sensor-data-type node is equal to
      'other' or unknown', then an node of this type MUST



Bierman, et al.          Expires April 21, 2016                [Page 17]


Internet-Draft           YANG Entity Management             October 2015


      contain a number ranging from -1000000000 to 1000000000.";
    reference "RFC 3433: EntitySensorValue";
  }

  typedef entity-sensor-status {
    type enumeration {
      enum ok {
        value 1;
        description
          "Indicates that the server can obtain the sensor value.";
      }
      enum unavailable {
        value 2;
        description
          "Indicates that the server presently cannot obtain the
           sensor value.";
      }
      enum nonoperational {
        value 3;
        description
          "Indicates that the server believes the sensor is broken.
           The sensor could have a hard failure (disconnected wire),
           or a soft failure such as out-of-range, jittery, or wildly
           fluctuating readings.";
      }
    }
    description
      "An node using this data type represents the operational
       status of a physical sensor.";
    reference "RFC 3433: EntitySensorStatus";
  }

  /*
   * Identities
   */

  identity entity-physical-class {
    description
      "This identity is the base for all physical entity class
       identifiers.";
  }


  /*
   * Operational state data nodes
   */

  container entity-state {



Bierman, et al.          Expires April 21, 2016                [Page 18]


Internet-Draft           YANG Entity Management             October 2015


    config false;
    description
      "Data nodes for the operational state of physical entities.";

    leaf last-change {
      type yang:date-and-time;
      description
        "The time the '/entity-state/physical-entity' list changed.";
    }

    list physical-entity {
      key name;
      description
        "List of physical entities";
      reference "RFC 6933: entPhysicalEntry";

      leaf name {
        type string;
        description
          "Administrative name assigned to this physical entity.
           No restrictions apply. Not required to be the same as
           entPhysicalName.";
      }

      leaf class {
        type identityref {
          base entity-physical-class;
        }
        mandatory true;
        description
          "An indication of the general hardware type
           of the physical entity.";
        reference "RFC 6933: entPhysicalClass";
      }

      leaf physical-index {
        if-feature entity-mib;
        type int32 {
          range "1..2147483647";
        }
        description
          "The entPhysicalIndex for the entPhysicalEntry represented
           by this list entry.";
        reference "RFC 6933: entPhysicalIndex";
      }

      leaf description {
        type string;



Bierman, et al.          Expires April 21, 2016                [Page 19]


Internet-Draft           YANG Entity Management             October 2015


        description
          "A textual description of physical entity.  This node
           should contain a string that identifies the manufacturer's
           name for the physical entity and should be set to a
           distinct value for each version or model of the physical
           entity.";
        reference "RFC 6933: entPhysicalDescr";
      }

      leaf-list contained-in {
        type leafref {
          path "../../physical-entity/name";
        }
        description
          "The name of the physical entity that 'contains'
           this physical entity.";
        reference "RFC 6933: entPhysicalContainedIn";
      }

      leaf-list contains-child {
        type leafref {
          path "../../physical-entity/name";
        }
        description
          "The name of the contained physical entity.";
        reference "RFC 6933: entPhysicalChildIndex";
      }

      leaf parent-rel-pos {
        type int32 {
          range "0 .. 2147483647";
        }
        description
          "An indication of the relative position of this child
           component among all its sibling components.  Sibling
           components are defined as physical entities that share the
           same instance values of each of the contained-in
           and class elements.";
        reference "RFC 6933: entPhysicalParentRelPos";
      }

      leaf hardware-rev {
        type string;
        description
          "The vendor-specific hardware revision string for the
           physical entity.  The preferred value is the hardware
           revision identifier actually printed on the component
           itself (if present).";



Bierman, et al.          Expires April 21, 2016                [Page 20]


Internet-Draft           YANG Entity Management             October 2015


        reference "RFC 6933: entPhysicalHardwareRev";
      }

      leaf firmware-rev {
        type string;
        description
          "The vendor-specific firmware revision string for the
           physical entity.";
        reference "RFC 6933: entPhysicalFirmwareRev";
      }

      leaf software-rev {
        type string;
        description
          "The vendor-specific software revision string for the
           physical entity.";
        reference "RFC 6933: entPhysicalSoftwareRev";
      }

      leaf serial-num {
        type string;
        description
          "The vendor-specific serial number string for the physical
           entity.  The preferred value is the serial number string
           actually printed on the component itself (if present).

           If a serial number has been configured for this entity in
           /entity/physical-entity/serial-num, this node contains the
           configured value.";
        reference "RFC 6933: entPhysicalSerialNum";
      }

      leaf mfg-name {
        type string;
        description
          "The name of the manufacturer of this physical component.
           The preferred value is the manufacturer name string
           actually printed on the component itself (if present).

           Note that comparisons between instances of the model-name,
           firmware-rev, software-rev, and the serial-num nodes are
           only meaningful amongst physical entities with the same
           value of mfg-name.

           If the manufacturer name string associated with the
           physical component is unknown to the server, then this
           node will contain a zero-length string.";
        reference "RFC 6933: entPhysicalMfgName";



Bierman, et al.          Expires April 21, 2016                [Page 21]


Internet-Draft           YANG Entity Management             October 2015


      }

      leaf model-name {
        type string;
        description
          "The vendor-specific model name identifier string associated
           with this physical component.  The preferred value is the
           customer-visible part number, which may be printed on the
           component itself.

           If the model name string associated with the physical
           component is unknown to the server, then this node will
           contain a zero-length string.";
        reference "RFC 6933: entPhysicalModelName";
      }

      leaf alias {
        type string {
          length "0 .. 32";
        }
        description
          "An 'alias' name for the physical entity, as specified by
           a network manager, and provides a non-volatile 'handle'
           for the physical entity.

           If an alias has been configured for this entity in
           /entity/physical-entity/alias, this node contains the
           configured value.  If no such alias has been configured,
           the server may set the value of this node to a locally
           unique value.";
        reference "RFC 6933: entPhysicalAlias";
      }

      leaf asset-id {
        type string {
          length "0 .. 32";
        }
        description
          "This node is a user-assigned asset tracking identifier
           (as specified by a network manager) for the physical entity
           and provides non-volatile storage of this information.

           If an asset tracking identifier has been configured for
           this entity in /entity/physical-entity/addet-id, this node
           contains the configured value.";
        reference "RFC 6933: entPhysicalAssetID";
      }




Bierman, et al.          Expires April 21, 2016                [Page 22]


Internet-Draft           YANG Entity Management             October 2015


      leaf is-fru {
        type boolean;
        description
          "This node indicates whether or not this physical entity
           is considered a 'field replaceable unit' by the vendor.  If
           this node contains the value 'true', then this
           physical entity identifies a field replaceable unit.  For
           all physical entities that represent components permanently
           contained within a field replaceable unit, the value
           'false' should be returned for this node.";
        reference "RFC 6933: entPhysicalIsFRU";
      }

      leaf mfg-date {
        type yang:date-and-time;
        description
          "The date of manufacturing of the managed entity.";
        reference "RFC 6933: entPhysicalMfgDate";
      }

      leaf-list uri {
        type inet:uri;
        description
          "This node contains identification information about the
           physical entity.

           If uris have been configured for this entity in
           /entity/physical-entity/uri, this node contains the
           configured values.";
        reference "RFC 6933: entPhysicalUris";
      }

      leaf uuid {
        type yang:uuid;
        description
          "A Universally Unique Identifier of the physical entity.";
        reference "RFC 6933: entPhysicalUUID";
      }

      container state {
        if-feature entity-state;
        description
          "State-related nodes";
        reference "RFC 4268: Entity State MIB";

        leaf state-last-changed {
          type yang:date-and-time;
          description



Bierman, et al.          Expires April 21, 2016                [Page 23]


Internet-Draft           YANG Entity Management             October 2015


            "The date and time when the value of any of the
             admin-state, oper-state, usage-state, alarm-status, or
             standby-status changed for this entity.

             If there has been no change since the last
             re-initialization of the local system, this node contains
             the date and time of local system initialization.  If there
             has been no change since the entity was added to the local
             system, this node contains the date and time of the
             insertion.";
          reference "RFC 4268: entStateLastChanged";
        }

        leaf admin-state {
          type entity-admin-state;
          description
            "The administrative state for this entity.

             This node refers to an entities administrative permission
             to service both other entities within its containment
             hierarchy as well other users of its services defined by
             means outside the scope of this module.

             Some physical entities exhibit only a subset of the
             remaining administrative state values.  Some entities
             cannot be locked, and hence this node exhibits only the
             'unlocked' state.  Other entities cannot be shutdown
             gracefully, and hence this node does not exhibit the
             'shutting-down' state.";
          reference "RFC 4268: entStateAdmin";
        }

        leaf oper-state {
          type entity-oper-state;
          description
            "The operational state for this entity.

             Note that this node does not follow the administrative
             state.  An administrative state of down does not predict an
             operational state of disabled.

             Note that some implementations may not be able to
             accurately report oper-state while the admin-state node
             has a value other than 'unlocked'.  In these cases, this
             node MUST have a value of 'unknown'.";
          reference "RFC 4268: entStateOper";
        }




Bierman, et al.          Expires April 21, 2016                [Page 24]


Internet-Draft           YANG Entity Management             October 2015


        leaf usage-state {
          type entity-usage-state;
          description
            "The usage state for this entity.

             This node refers to an entity's ability to service more
             physical entities in a containment hierarchy.

             Some entities will exhibit only a subset of the usage state
             values.  Entities that are unable to ever service any
             entities within a containment hierarchy will always have a
             usage state of 'busy'.  Some entities will only ever be
             able to support one entity within its containment hierarchy
             and will therefore only exhibit values of 'idle' and
             'busy'.";
          reference "RFC 4268, entStateUsage";
        }

        leaf alarm-status {
          type entity-alarm-status;
          description
            "The alarm status for this entity.  It does not include
             the alarms raised on child components within its
             containment hierarchy.";
          reference "RFC 4268: entStateAlarm";
        }

        leaf standby-status {
          type entity-standby-status;
          description
            "The standby status for this entity.

             Some entities will exhibit only a subset of the
             remaining standby state values.  If this entity
             cannot operate in a standby role, the value of this
             node will always be 'providing-service'.";
          reference "RFC 4268: entStateStandby";
        }
      }

      container sensor-data {
        when 'derived-from-or-self(../class,
                                   "iana-entity", "sensor")' {
          description
            "Sensor data nodes present for any entity of type 'sensor'";
        }
        if-feature entity-sensor;
        description



Bierman, et al.          Expires April 21, 2016                [Page 25]


Internet-Draft           YANG Entity Management             October 2015


          "Sensor-related nodes.";
        reference "RFC 3433: Entity Sensor MIB";

        leaf data-type {
          type entity-sensor-data-type;
          description
            "The type of data units associated with the
             sensor value";
          reference "RFC 3433: entPhySensorType";
        }

        leaf data-scale {
          type entity-sensor-data-scale;
          description
            "The (power of 10) scaling factor associated
             with the sensor value";
          reference "RFC 3433: entPhySensorScale";
        }

        leaf precision {
          type entity-sensor-precision;
          description
            "The number of decimal places of precision
             associated with the sensor value";
          reference "RFC 3433: entPhySensorPrecision";
        }

        leaf value {
          type entity-sensor-value;
          description
            "The most recent measurement obtained by the server
             for this sensor.";
          reference "RFC 3433: entPhySensorValue";
        }

        leaf oper-status {
          type entity-sensor-status;
          description
            "The operational status of the sensor.";
          reference "RFC 3433: entPhySensorOperStatus";
        }

        leaf sensor-units-display {
          type string;
          description
            "A textual description of the data units that should be
             used in the display of the sensor value.";
          reference "RFC 3433: entPhySensorUnitsDisplay";



Bierman, et al.          Expires April 21, 2016                [Page 26]


Internet-Draft           YANG Entity Management             October 2015


        }

        leaf value-timestamp {
          type yang:date-and-time;
          description
            "The time the status and/or value of this sensor was
             last obtained by the server.";
          reference "RFC 3433: entPhySensorValueTimeStamp";
        }

        leaf value-update-rate {
          type uint32;
          units "milliseconds";
          description
            "An indication of the frequency that the server updates
             the associated 'value' node, representing in
             milliseconds.  The value zero indicates:

              - the sensor value is updated on demand (e.g.,
                when polled by the server for a get-request),
              - the sensor value is updated when the sensor
                value changes (event-driven),
              - the server does not know the update rate.";
          reference "RFC 3433: entPhySensorValueUpdateRate";
        }
      }
    }
  }

  /*
   * Configuration data nodes
   */

  container entity {
    if-feature entity-config;
    description
      "Configuration parameters for physical entities.";

    list physical-entity {
      key name;
      description
        "List of configuration data for physical entities.";

      leaf name {
        type string;
        description
          "Administrative name assigned to this physical entity.
           No restrictions apply.";



Bierman, et al.          Expires April 21, 2016                [Page 27]


Internet-Draft           YANG Entity Management             October 2015


      }

      leaf serial-num {
        type string;
        description
          "The vendor-specific serial number string for the physical
           entity.  The preferred value is the serial number string
           actually printed on the component itself (if present).

           This node is indented to be used for physical entities
           for which the server cannot determine the serial number.";
        reference "RFC 6933: entPhysicalSerialNum";
      }

      leaf alias {
        type string {
          length "0 .. 32";
        }
        description
          "This node is an 'alias' name for the physical entity, as
           specified by a network manager, and provides a non-volatile
           'handle' for the physical entity.";
        reference "RFC 6933: entPhysicalAlias";
      }

      leaf asset-id {
        type string {
          length "0 .. 32";
        }
        description
          "This node is a user-assigned asset tracking identifier
           (as specified by a network manager) for the physical entity";
        reference "RFC 6933: entPhysicalAssetID";
      }

      leaf-list uri {
        type inet:uri;
        description
          "This node contains identification information about the
           physical entity.";
        reference "RFC 6933: entPhysicalUris";
      }

      leaf admin-state {
        if-feature entity-state;
        type entity-admin-state;
        description
          "The administrative state for this entity.



Bierman, et al.          Expires April 21, 2016                [Page 28]


Internet-Draft           YANG Entity Management             October 2015


           This node refers to an entity's administrative
           permission to service both other entities within
           its containment hierarchy as well other users of
           its services defined by means outside the scope
           of this module.

           Some physical entities exhibit only a subset of the
           remaining administrative state values.  Some entities
           cannot be locked, and hence this node exhibits only
           the 'unlocked' state.  Other entities cannot be shutdown
           gracefully, and hence this node does not exhibit the
           'shutting-down' state.";
        reference "RFC 4268, entStateAdmin";
      }
    }
  }

  /*
   * Notifications
   */

  notification ent-config-change {
    description
      "An ent-config-change notification is generated when the value
       of /entity-state/last-change changes.";
    reference "RFC 6933, entConfigChange";
  }

  notification ent-state-oper-enabled {
    if-feature entity-state;
    description
      "An ent-state-oper-enabled notification signifies that
       an entity has transitioned into the 'enabled' state.";

    leaf name {
      type leafref {
        path "/entity-state/physical-entity/name";
      }
      description
        "The name of the entity that has transitioned into the
         'enabled' state.";
    }
    leaf admin-state {
      type leafref {
        path "/entity-state/physical-entity/state/admin-state";
      }
      description
        "The administrative state for the entity.";



Bierman, et al.          Expires April 21, 2016                [Page 29]


Internet-Draft           YANG Entity Management             October 2015


    }
    leaf alarm-status {
      type leafref {
        path "/entity-state/physical-entity/state/alarm-status";
      }
      description
        "The alarm status for the entity.";
    }
    reference "RFC 4268, entStateOperEnabled";
  }

  notification ent-state-oper-disabled {
    if-feature entity-state;
    description
      "An ent-state-oper-disabled notification signifies that
       an entity has transitioned into the 'disabled' state.";

    leaf name {
      type leafref {
        path "/entity-state/physical-entity/name";
      }
      description
        "The name of the entity that has transitioned into the
         'disabled' state.";
    }
    leaf admin-state {
      type leafref {
        path "/entity-state/physical-entity/state/admin-state";
      }
      description
        "The administrative state for the entity.";
    }
    leaf alarm-status {
      type leafref {
        path "/entity-state/physical-entity/state/alarm-status";
      }
      description
        "The alarm status for the entity.";
    }
    reference "RFC 4268, entStateOperDisabled";
  }

}

   <CODE ENDS>

   Move this to a separate document?:




Bierman, et al.          Expires April 21, 2016                [Page 30]


Internet-Draft           YANG Entity Management             October 2015


   <CODE BEGINS> file "iana-entity@2015-10-19.yang"

  module iana-entity {
    namespace "urn:ietf:params:xml:ns:yang:iana-entity";
    prefix ianaent;

    import ietf-entity {
      prefix ent;
    }

    organization "IANA";
    contact
      "        Internet Assigned Numbers Authority

       Postal: ICANN
               4676 Admiralty Way, Suite 330
               Marina del Rey, CA 90292

       Tel:    +1 310 823 9358
       <mailto:iana@iana.org>";


    description
      "IANA defined identities for physical class.";
    reference
      "https://www.iana.org/assignments/ianaentity-mib/ianaentity-mib";

    // RFC Ed.: replace XXXX with actual RFC number and remove this
    // note.

    // RFC Ed.: update the date below with the date of RFC publication
    // and remove this note.
    revision 2015-10-19 {
      description
        "Initial revision.";
      reference
        "RFC XXXX: A YANG Data Model for Entity Managemet";
    }

    identity unknown {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is unknown to the server.";
    }

    identity chassis {
      base ent:entity-physical-class;



Bierman, et al.          Expires April 21, 2016                [Page 31]


Internet-Draft           YANG Entity Management             October 2015


      description
        "This identity is applicable if the physical entity class
         is an overall container for networking equipment.  Any class of
         physical entity, except a stack, may be contained within a
         chassis; a chassis may only be contained within a stack.";
    }

    identity backplane {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of device for aggregating and forwarding
         networking traffic, such as a shared backplane in a modular
         ethernet switch.  Note that an implementation may model a
         backplane as a single physical entity, which is actually
         implemented as multiple discrete physical components (within a
         chassis or stack).";
    }

    identity container {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is capable of containing one or more removable physical
         entities, possibly of different types.  For example, each
         (empty or full) slot in a chassis will be modeled as a
         container.  Note that all removable physical entities should be
         modeled within a container entity, such as field-replaceable
         modules, fans, or power supplies.  Note that all known
         containers should be modeled by the agent, including empty
         containers.";
    }

    identity power-supply {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is a power-supplying component.";
    }

    identity fan {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is a fan or other heat-reduction component.";
    }

    identity sensor {



Bierman, et al.          Expires April 21, 2016                [Page 32]


Internet-Draft           YANG Entity Management             October 2015


      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of sensor, such as a temperature sensor within a
         router chassis.";
    }

    identity module {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of self-contained sub-system.  If a 'module'
         entity is removable, then it should be modeled within a
         container entity; otherwise, it should be modeled directly
         within another physical entity (e.g., a chassis or another
         module).";
    }

    identity port {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of networking port, capable of receiving and/or
         transmitting networking traffic.";
    }

    identity stack {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of super-container (possibly virtual) intended to
         group together multiple chassis entities.  A stack may be
         realized by a 'virtual' cable, a real interconnect cable
         attached to multiple chassis, or multiple interconnect cables.
         A stack should not be modeled within any other physical
         entities, but a stack may be contained within another stack.
         Only chassis entities should be contained within a stack.";
    }

    identity cpu {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of central processing unit.";
    }

    identity energy-object {
      base ent:entity-physical-class;



Bierman, et al.          Expires April 21, 2016                [Page 33]


Internet-Draft           YANG Entity Management             October 2015


      description
        "This identity is applicable if the physical entity class
         is some sort of energy object, i.e., a piece of equipment that
         is part of or attached to a communications network that is
         monitored, controlled, or aids in the management of another
         device for Energy Management.";
    }

    identity battery {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of battery.";
    }

    identity storage-drive {
      base ent:entity-physical-class;
      description
        "This identity is applicable if the physical entity class
         is some sort of entity with data storage capability as main
         functionality, e.g., disk drive (HDD), solid state device
         (SSD), hybrid (SSHD), object storage (OSD) or other.";
    }
  }


   <CODE ENDS>

8.  IANA Considerations

   This document registers a URI in the IETF XML registry [RFC3688].
   Following the format in RFC 3688, the following registration is
   requested to be made.

        URI: TBD

        Registrant Contact: The IESG.

        XML: N/A, the requested URI is an XML namespace.

   This document registers a YANG module in the YANG Module Names
   registry [RFC6020].

     name:         ietf-entity
     namespace:    TBD
     prefix:       ent
     reference:    RFC XXXX




Bierman, et al.          Expires April 21, 2016                [Page 34]


Internet-Draft           YANG Entity Management             October 2015


9.  Security Considerations

   TBD

10.  Acknowledgements

   TBD

11.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3433]  Bierman, A., Romascanu, D., and K. Norseth, "Entity Sensor
              Management Information Base", RFC 3433, DOI 10.17487/
              RFC3433, December 2002,
              <http://www.rfc-editor.org/info/rfc3433>.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              January 2004.

   [RFC4268]  Chisholm, S. and D. Perkins, "Entity State MIB", RFC 4268,
              DOI 10.17487/RFC4268, November 2005,
              <http://www.rfc-editor.org/info/rfc4268>.

   [RFC6020]  Bjorklund, M., "YANG - A Data Modeling Language for the
              Network Configuration Protocol (NETCONF)", RFC 6020,
              October 2010.

   [RFC6933]  Bierman, A., Romascanu, D., Quittek, J., and M.
              Chandramouli, "Entity MIB (Version 4)", RFC 6933, DOI
              10.17487/RFC6933, May 2013,
              <http://www.rfc-editor.org/info/rfc6933>.

Authors' Addresses

   Andy Bierman
   YumaWorks

   Email: andy@yumaworks.com


   Martin Bjorklund
   Tail-f Systems

   Email: mbj@tail-f.com





Bierman, et al.          Expires April 21, 2016                [Page 35]


Internet-Draft           YANG Entity Management             October 2015


   Jie Dong
   Huawei Technologies

   Email: jie.dong@huawei.com


   Dan Romascanu
   Avaya

   Email: dromasca@avaya.com









































Bierman, et al.          Expires April 21, 2016                [Page 36]