Internet Engineering Task Force G.Galimberti, Ed.
Internet-Draft Cisco
Intended status: Standards Track R.Kunze, Ed.
Expires: September 18, 2016 Deutsche Telekom
Kam Lam, Ed.
Alcatel-Lucent
D. Hiremagalur, Ed.
Juniper
L.Fang, Ed.
G.Ratterree, Ed.
Microsoft
March 17, 2016
An SNMP MIB extension to RFC3591 to manage optical interface parameters
of "G.698.2 single channel" in DWDM applications
draft-galikunze-ccamp-dwdm-if-snmp-mib-01
Abstract
This memo defines a module of the Management Information Base (MIB)
used by Simple Network Management Protocol (SNMP) in TCP/IP- based
internet. In particular, it defines objects for managing single
channel optical interface parameters of DWDM applications, using the
approach specified in G.698.2 [ITU.G698.2] . This interface,
described in ITU-T G.872, G.709 and G.798, is one type of OTN multi-
vendor Intra-Domain Interface (IaDI). This RFC is an extension of
RFC3591 to support the optical parameters specified in ITU-T G.698.2
and application identifiers specified in ITU-T G.874.1 [ITU.G874.1].
Note that G.874.1 encompasses vendor-specific codes, which if used
would make the interface a single vendor IaDI and could still be
managed.
The MIB module defined in this memo can be used for Optical
Parameters monitoring and/or configuration of the endpoints of the
multi-vendor IaDI based on the Black Link approach.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
G.Galimberti, et al. Expires September 18, 2016 [Page 1]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 18, 2016.
Copyright Notice
Copyright (c) 2016 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . 4
3. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1. Use Cases . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2. Optical Parameters Description . . . . . . . . . . . . . 6
4.2.1. Rs-Ss Configuration . . . . . . . . . . . . . . . . . 6
4.2.2. Table of Application Identifiers . . . . . . . . . . 7
4.3. Use of ifTable . . . . . . . . . . . . . . . . . . . . . 8
4.3.1. Use of ifTable for OPS Layer . . . . . . . . . . . . 10
4.3.2. Use of ifTable for OCh Layer . . . . . . . . . . . . 11
4.3.3. Use of ifStackTable . . . . . . . . . . . . . . . . . 11
5. Structure of the MIB Module . . . . . . . . . . . . . . . . . 12
6. Object Definitions . . . . . . . . . . . . . . . . . . . . . 12
7. Relationship to Other MIB Modules . . . . . . . . . . . . . . 19
7.1. Relationship to the [TEMPLATE TODO] MIB . . . . . . . . . 19
7.2. MIB modules required for IMPORTS . . . . . . . . . . . . 19
8. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 19
9. Security Considerations . . . . . . . . . . . . . . . . . . . 19
G.Galimberti, et al. Expires September 18, 2016 [Page 2]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20
11. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 20
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 21
12.1. Normative References . . . . . . . . . . . . . . . . . . 21
12.2. Informative References . . . . . . . . . . . . . . . . . 24
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 24
Appendix B. Open Issues . . . . . . . . . . . . . . . . . . . . 24
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 24
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
used by Simple Network Management Protocol (SNMP)in TCP/IP-based
internets. In particular, it defines objects for managing single
channel optical interface parameters of DWDM applications, using the
approach specified in G.698.2. This RFC is an extension of RFC3591
to support the optical parameters specified in ITU-T G.698.2
[ITU.G698.2] and application identifiers specified in ITU-T G.874.1
[ITU.G874.1] . Note that G.874.1 encompasses vendor-specific codes,
which if used would make the interface a single vendor IaDI and could
still be managed.
The Black Link approach allows supporting an optical transmitter/
receiver pair of one vendor to inject an optical tributary signal and
run it over an optical network composed of amplifiers, filters, add-
drop multiplexers from a different vendor. In the OTN architecture,
the 'black-link' represents a pre-certified network media channel
conforming to G.698.2 specifications at the S and R reference points.
[Editor's note: In G.698.2 this corresponds to the optical path from
point S to R; network media channel is also used and explained in
draft-ietf-ccamp-flexi-grid-fwk-02]
Management will be performed at the edges of the network media
channel (i.e., at the transmitters and receivers attached to the S
and R reference points respectively) for the relevant parameters
specified in G.698.2 [ITU.G698.2], G.798 [ITU.G798], G.874
[ITU.G874], and the performance parameters specified in G.7710/Y.1701
[ITU-T G.7710] and G.874.1 [ITU.G874.1].
G.698.2 [ITU.G698.2] is primarily intended for metro applications
that include optical amplifiers. Applications are defined in G.698.2
[ITU.G698.2] using optical interface parameters at the single-channel
connection points between optical transmitters and the optical
multiplexer, as well as between optical receivers and the optical
demultiplexer in the DWDM system. This Recommendation uses a
methodology which does not explicitly specify the details of the
optical network between reference point Ss and Rs, e.g., the passive
G.Galimberti, et al. Expires September 18, 2016 [Page 3]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
and active elements or details of the design. The Recommendation
currently includes unidirectional DWDM applications at 2.5 and 10
Gbit/s (with 100 GHz and 50 GHz channel frequency spacing). Work is
still under way for 40 and 100 Gbit/s interfaces. There is
possibility for extensions to a lower channel frequency spacing.
This document specifically refers to the "application code" defined
in the G.698.2 [ITU.G698.2] and included in the Application
Identifier defined in G.874.1 [ITU.G874.1] and G.872 [ITU.G872], plus
a few optical parameters not included in the G.698.2 application code
specification.
This draft refers and supports also the draft-kunze-g-698-2-
management-control-framework
The building of an SNMP MIB describing the optical parameters defined
in G.698.2 [ITU.G698.2], and reflected in G.874.1 [ITU.G874], allows
the different vendors and operator to retrieve, provision and
exchange information across the G.698.2 multi-vendor IaDI in a
standardized way.
The MIB, reporting the Optical parameters and their values,
characterizes the features and the performances of the optical
components and allow a reliable black link design in case of multi
vendor optical networks.
Although RFC 3591 [RFC3591] describes and defines the SNMP MIB of a
number of key optical parameters, alarms and Performance Monitoring,
as this RFC is over a decade old, it is primarily pre-OTN, and a more
complete and up-to-date description of optical parameters and
processes can be found in the relevant ITU-T Recommendations. The
same considerations can be applied to the RFC 4054 [RFC4054]
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
G.Galimberti, et al. Expires September 18, 2016 [Page 4]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
3. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119] In
the description of OIDs the convention: Set (S) Get (G) and Trap (T)
conventions will describe the action allowed by the parameter.
4. Overview
Figure 1 shows a set of reference points, for the linear "black link"
approach, for single-channel connection (Ss and Rs) between
transmitters (Tx) and receivers (Rx). Here the DWDM network elements
include an OM and an OD (which are used as a pair with the opposing
element), one or more optical amplifiers and may also include one or
more OADMs.
+-------------------------------------------------+
Ss | DWDM Network Elements | Rs
+---+ | | | \ / | | | +--+
Tx L1----|->| \ +------+ +------+ / |--|-->Rx L1
+---+ | | | | | +------+ | | | | | +--+
+---+ | | | | | | | | | | | | +--+
Tx L2----|->| OM |-->|------|->| OADM |--|------|->| OD |--|-->Rx L2
+---+ | | | | | | | | | | | | +--+
+---+ | | | | | +------+ | | | | | +--+
Tx L3----|->| / | DWDM | | ^ | DWDM | \ |--|-->Rx L3
+---+ | | / | Link +----|--|----+ Link | \ | | +--+
+-----------+ | | +----------+
+--+ +--+
| |
Rs v | Ss
+-----+ +-----+
|RxLx | |TxLx |
+-----+ +-----+
Ss = reference point at the DWDM network element tributary output
Rs = reference point at the DWDM network element tributary input
Lx = Lambda x
OM = Optical Mux
OD = Optical Demux
OADM = Optical Add Drop Mux
from Fig. 5.1/G.698.2
Figure 1: Linear Black Link approach
G.Galimberti, et al. Expires September 18, 2016 [Page 5]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
G.698.2 [ITU.G698.2] defines also Ring "Black Link" approach
configurations [Fig. 5.2/G.698.2] and Linear "black link" approach
for Bidirectional applications[Fig. 5.3/G.698.2]
4.1. Use Cases
The use cases are described in draft-kdkgall-ccamp-dwdm-if-mng-ctrl-
fwk
4.2. Optical Parameters Description
The G.698.2 pre-certified network media channels are managed at the
edges, i.e. at the transmitters (Tx) and receivers (Rx) attached to
the S and R reference points respectively. The set of parameters
that could be managed are specified in G.698.2 [ITU.G698.2] section
5.3 referring the "application code" notation
The definitions of the optical parameters are provided below to
increase the readability of the document, where the definition is
ended by (G) the parameter can be retrieve with a GET, when (S) it
can be provisioned by a SET, (G,S) can be either GET and SET.
To support the management of these parameters, the SNMP MIB in RFC
3591 [RFC3591] is extended with a new MIB module defined in section 6
of this document. This new MIB module includes the definition of new
configuration table of the OCh Layer for the parameters at Tx (S) and
Rx (R).
4.2.1. Rs-Ss Configuration
The Rs-Ss configuration table allows configuration of Central
Frequency, Power and Application identifiers as described in
[ITU.G698.2] and G.694.1 [ITU.G694.1]
This parameter report the current Transceiver Output power, it can be
either a setting and measured value (G, S).
Central frequency (see G.694.1 Table 1):
This parameter indicates the central frequency value that Ss and
Rs will be set, to work (in THz), in particular Section 6/G.694.1
(G, S).
Single-channel application identifiers (see G.698.2):
This parameter indicates the transceiver application identifier at
Ss and Rs as defined in [ITU.G698.2] Chapter 5.4 - this parameter
can be called Optical Interface Identifier OII as per [draft-
martinelli-wson-interface-class] (G).
Number of Single-channel application identifiers Supported
G.Galimberti, et al. Expires September 18, 2016 [Page 6]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
This parameter indicates the number of Single-channel application
codes supported by this interface (G).
Current Laser Output power:
This parameter report the current Transceiver Output power, see
RFC3591.
Current Laser Input power:
This parameter report the current Transceiver Input power see
RFC3591.
+---------------------------------------------+---------+-----------+
| PARAMETERS | Get/Set | Reference |
+---------------------------------------------+---------+-----------+
| Central Frequency | G,S | G.694.1 |
| | | S.6 |
| Single-channel Application Identifier | G | G.874.1 |
| number in use | | |
| Single-channel Application Identifier Type | G | G.874.1 |
| in use | | |
| Single-channel Application Identifier in | G | G.874.1 |
| use | | |
| Number of Single-channel Application | G | N.A. |
| Identifiers Supported | | |
| Current Output Power | G,S | RFC3591 |
| Current Input Power | G | RFC3591 |
+---------------------------------------------+---------+-----------+
Table 1: Rs-Ss Configuration
4.2.2. Table of Application Identifiers
This table has a list of Application Identifiers supported by this
interface at point R are defined in G.698.2.
G.Galimberti, et al. Expires September 18, 2016 [Page 7]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Application Identifier Number:
The number that uniquely identifies the Application Identifier.
Application Identifier Type:
Type of application Identifier: STANDARD / PROPRIETARY in G.874.1
Note: if the A.I. type = PROPRIETARY, the first 6 Octets of the
Application Identifier (PrintableString) must contain the
Hexadecimal representation of an OUI (organizationally unique
identifier) assigned to the vendor whose implementation generated
the Application Identifier; the remaining octets of the
PrintableString are unspecified.
Application Identifier:
This is the application Identifier that is defined in G.874.1.
4.3. Use of ifTable
This section specifies how the MIB II interfaces group, as defined in
RFC 2863 [RFC2863], is used for the link ends of a black link. Only
the ifGeneralInformationGroup will be supported for the ifTable and
the ifStackTable to maintain the relationship between the OCh and OPS
layers. The OCh and OPS layers are managed in the ifTable using
IfEntries that correlate to the layers depicted in Figure 1.
For example, a device with TX and/or RX will have an Optical Physical
Section (OPS) layer, and an OCh layer. There is a one to n
relationship between the OPS and OCh layers.
EDITOR NOTE: Reason for changing from OChr to OCh: Edition 3 of G.872
removed OChr from the architecture and G.709 was subsequently updated
to account for this architectural change.
G.Galimberti, et al. Expires September 18, 2016 [Page 8]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Figure 2 In the following figures, opticalPhysicalSection are
abbreviated as OPS.
_____________________
\
Path Data Unit |\
(ODUk) | \
_____________________| \ __________________
| | | >
Tandem Data Unit | | | |
(ODUkT) | | OCh Layer | > n och IfEntries
_____________________| | | |
| |__________________| >
Optical | /| | >
Transport Unit | / | | |
(OTUk) |/ | OPSn Layer | > m ops IfEntries
_____________________/ | | |
|__________________| >
Figure 2: OTN Layers for OPS and OCh
Each opticalChannel IfEntry is mapped to one of the m
opticalPhysicalSection IfEntries, where m is greater than or equal to
1. Conversely, each opticalTransPhysicalSection port entry is mapped
to one of the n opticalChannel IfEntries, where n is greater than or
equal to 1.
The design of the Optical Interface MIB provides the option to model
an interface either as a single bidirectional object containing both
sink and source functions or as a pair of unidirectional objects, one
containing sink functions and the other containing source functions.
If the sink and source for a given protocol layer are to be modelled
as separate objects, then there need to be two ifTable entries, one
that corresponds to the sink and one that corresponds to the source,
where the directionality information is provided in the configuration
tables for that layer via the associated Directionality objects. The
agent is expected to maintain consistent directionality values
between ifStackTable layers (e.g., a sink must not be stacked in a
1:1 manner on top of a source, or vice-versa), and all protocol
layers that are represented by a given ifTable entry are expected to
have the same directionality.
G.Galimberti, et al. Expires September 18, 2016 [Page 9]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
When separate ifTable entries are used for the source and sink
functions of a given physical interface, association between the two
uni-directional ifTable entries (one for the source function and the
other for the sink functions) should be provided. It is recommended
that identical ifName values are used for the two ifTable entries to
indicate such association. An implementation shall explicitly state
what mechanism is used to indicate the association, if ifName is not
used.
4.3.1. Use of ifTable for OPS Layer
Only the ifGeneralInformationGroup needs to be supported.
ifTable Object Use for OTN OPS Layer
==================================================================
ifIndex The interface index.
ifDescr Optical Transport Network (OTN) Optical
Physical Section (OPS)
ifType opticalPhysicalSection (xxx)
<<<Editor Note: Need new IANA registration value for xxx. >>>
ifSpeed Actual bandwidth of the interface in bits per
second. If the bandwidth of the interface is
greater than the maximum value of 4,294,967,295
then the maximum value is reported and
ifHighSpeed must be used to report the
interface's speed.
ifPhysAddress An octet string with zero length. (There is
no specific address associated with the
interface.)
ifAdminStatus The desired administrative state of the
interface. Supports read-only access.
ifOperStatus The operational state of the interface. The
value lowerLayerDown(7) is not used, since
there is no lower layer interface. This object
is set to notPresent(6) if a component is
missing, otherwise it is set to down(2) if
either of the objects optIfOPSnCurrentStatus
indicates that any defect is present.
G.Galimberti, et al. Expires September 18, 2016 [Page 10]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
ifLastChange The value of sysUpTime at the last change in
ifOperStatus.
ifName Enterprise-specific convention (e.g., TL-1 AID)
to identify the physical or data entity
associated with this interface or an
OCTET STRING of zero length. The
enterprise-specific convention is intended to
provide the means to reference one or more
enterprise-specific tables.
ifLinkUpDownTrapEnable Default value is enabled(1). Supports
read-only access.
ifHighSpeed Actual bandwidth of the interface in Mega-bits
per second. A value of n represents a range of
'n-0.5' to 'n+0.499999'.
ifConnectorPresent Set to true(1).
ifAlias The (non-volatile) alias name for this interface
as assigned by the network manager.
4.3.2. Use of ifTable for OCh Layer
Use of ifTable for OCh Layer See RFC 3591 [RFC3591] section 2.4
4.3.3. Use of ifStackTable
Use of the ifStackTable and ifInvStackTable to associate the
opticalPhysicalSection and opticalChannel interface entries is best
illustrated by the example shown in Figure 3. The example assumes an
ops interface with ifIndex i that carries two multiplexed OCh
interfaces with ifIndex values of j and k, respectively. The example
shows that j and k are stacked above (i.e., multiplexed into) i.
Furthermore, it shows that there is no layer lower than i and no
layer higher than j and/or k.
G.Galimberti, et al. Expires September 18, 2016 [Page 11]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Figure 3
HigherLayer LowerLayer
--------------------------
0 j
0 k
j i
k i
i 0
Figure 3: Use of ifStackTable for an OTN port
For the inverse stack table, it provides the same information as the
interface stack table, with the order of the Higher and Lower layer
interfaces reversed.
5. Structure of the MIB Module
EDITOR NOTE:text will be provided based on the MIB module in
Section 6
6. Object Definitions
EDITOR NOTE: Once the scope in Section 1 and the parameters in
Section 4 are finalized, a MIB module will be defined. It could be
an extension to the OPT-IF-MIB module of RFC 3591. >>>
G.Galimberti, et al. Expires September 18, 2016 [Page 12]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
OPT-IF-698-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32,
Integer32,
Unsigned32,
Counter64,
transmission,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
RowPointer,
RowStatus,
TruthValue,
DisplayString,
DateAndTime
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
optIfMibModule
FROM OPT-IF-MIB;
-- This is the MIB module for the optical parameters -
-- Application codes associated with the black link end points.
optIfXcvrMibModule MODULE-IDENTITY
LAST-UPDATED "201401270000Z"
ORGANIZATION "IETF Ops/Camp MIB Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/
Mailing Lists:
Editor: Gabriele Galimberti
Email: ggalimbe@cisco.com"
DESCRIPTION
"The MIB module to describe Black Link tranceiver
characteristics to rfc3591.
G.Galimberti, et al. Expires September 18, 2016 [Page 13]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Copyright (C) The Internet Society (2014). This version
of this MIB module is an extension to rfc3591; see the RFC
itself for full legal notices."
REVISION "201305050000Z"
DESCRIPTION
"Draft version 1.0"
REVISION "201305050000Z"
DESCRIPTION
"Draft version 2.0"
REVISION "201302270000Z"
DESCRIPTION
"Draft version 3.0"
REVISION "201307020000Z"
DESCRIPTION
"Draft version 4.0
Changed the draft to include only the G.698 parameters."
REVISION "201311020000Z"
DESCRIPTION
"Draft version 5.0
Mib has a table of application code/vendor
transcievercode G.698"
REVISION "201401270000Z"
DESCRIPTION
"Draft version 6.0"
REVISION "201407220000Z"
DESCRIPTION
"Draft version 8.0
Removed Vendor transceiver code"
REVISION "201502220000Z"
DESCRIPTION
"Draft version 11.0
Added reference to OUI in the first 6 Octets of a
proprietary Application code
Added a Length field for the Application code
Changed some names"
REVISION "201507060000Z"
DESCRIPTION
"Draft version 12.0
Added Power Measurement Use Cases
and ITU description" "
::= { optIfMibModule 4 }
::= { optIfMibModule 4 }
-- Addition to the RFC 3591 objects
optIfOChSsRsGroup OBJECT IDENTIFIER ::= { optIfXcvrMibModule 1 }
G.Galimberti, et al. Expires September 18, 2016 [Page 14]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
-- OCh Ss/Rs config table
-- The application code/vendor tranceiver class for the Black Link
-- Ss-Rs will be added to the OchConfigTable
optIfOChSsRsConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSsRsConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Och General config extension parameters"
::= { optIfOChSsRsGroup 1 }
optIfOChSsRsConfigEntry OBJECT-TYPE
SYNTAX OptIfOChSsRsConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains G.698 parameters for an
interface."
INDEX { ifIndex }
::= { optIfOChSsRsConfigTable 1 }
OptIfOChSsRsConfigEntry ::=
SEQUENCE {
optIfOChCentralFrequency Unsigned32,
optIfOChCfgApplicationIdentifierNumber Unsigned32,
optIfOChCfgApplicationIdentifierType Unsigned32,
optIfOChCfgApplicationIdentifierLength Unsigned32,
optIfOChCfgApplicationIdentifier DisplayString,
optIfOChNumberApplicationCodesSupported Unsigned32
}
optIfOChCentralFrequency OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
UNITS "THz"
STATUS current
DESCRIPTION
" This parameter indicates the frequency of this interface.
"
::= { optIfOChSsRsConfigEntry 1 }
optIfOChCfgApplicationIdentifierNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter uniquely indicates the transceiver
G.Galimberti, et al. Expires September 18, 2016 [Page 15]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
application code at Ss and Rs as defined in [ITU.G874.1],
that is used by this interface.
The optIfOChSrcApplicationIdentifierTable has all the
application codes supported by this interface. "
::= { optIfOChSsRsConfigEntry 2 }
optIfOChCfgApplicationIdentifierType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter indicates the transceiver type of
application code at Ss and Rs as defined in [ITU.G874.1],
that is used by this interface.
The optIfOChSrcApplicationIdentifierTable has all the
application codes supported by this interface
Standard = 0, PROPRIETARY = 1. "
::= { optIfOChSsRsConfigEntry 3 }
optIfOChCfgApplicationIdentifierLenght OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter indicates the number of octets in the
Application Identifier.
"
::= { optIfOChSsRsConfigEntry 4 }
optIfOChCfgApplicationIdentifier OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter indicates the transceiver application code
at Ss and Rs as defined in [ITU.G698.2] Chapter 5.3, that
is used by this interface. The
optIfOChSrcApplicationCodeTable has all the application
codes supported by this interface.
If the optIfOChCfgApplicationIdentifierType is 1
(Proprietary), then the first 6 octets of the printable
string will be the OUI (organizationally unique identifier)
assigned to the vendor whose implementation generated the
Application Identifier."
::= { optIfOChSsRsConfigEntry 5 }
optIfOChNumberApplicationIdentifiersSupported OBJECT-TYPE
G.Galimberti, et al. Expires September 18, 2016 [Page 16]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Number of Application codes supported by this interface."
::= { optIfOChSsRsConfigEntry 6 }
-- Table of Application codes supported by the interface
-- OptIfOChSrcApplicationCodeEntry
optIfOChSrcApplicationIdentifierTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSrcApplicationIdentifierEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Table of Application codes supported by this interface."
::= { optIfOChSsRsGroup 2 }
optIfOChSrcApplicationIdentifierEntry OBJECT-TYPE
SYNTAX OptIfOChSrcApplicationIdentifierEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the Application code for
this interface."
INDEX { ifIndex, optIfOChApplicationIdentiferNumber }
::= { optIfOChSrcApplicationIdentifierTable 1 }
OptIfOChSrcApplicationIdentifierEntry ::=
SEQUENCE {
optIfOChApplicationIdentiferNumber Integer32,
optIfOChApplicationIdentiferType Integer32,
optIfOChApplicationIdentiferLength Integer32,
optIfOChApplicationIdentifier DisplayString
}
optIfOChApplicationIdentiferNumber OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" The number/identifier of the application code supported at
this interface. The interface can support more than one
application codes.
"
::= { optIfOChSrcApplicationIdentifierEntry 1}
G.Galimberti, et al. Expires September 18, 2016 [Page 17]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
optIfOChApplicationIdentiferType OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The type of identifier of the application code supported at
this interface. The interface can support more than one
application codes.
Standard = 0, PROPRIETARY = 1
"
::= { optIfOChSrcApplicationIdentifierEntry 2}
optIfOChApplicationIdentiferLength OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" This parameter indicates the number of octets in the
Application Identifier.
"
::= { optIfOChSrcApplicationIdentifierEntry 3}
optIfOChApplicationIdentifier OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The application code supported by this interface DWDM
link.
If the optIfOChApplicationIdentiferType is 1 (Proprietary),
then the first 6 octets of the printable string will be
the OUI (organizationally unique identifier) assigned to
the vendor whose implementation generated the Application
Identifier."
::= { optIfOChSrcApplicationIdentifierEntry 4}
-- Notifications
-- Central Frequency Change Notification
optIfOChCentralFrequencyChange NOTIFICATION-TYPE
OBJECTS { optIfOChCentralFrequency }
STATUS current
DESCRIPTION
"Notification of a change in the central frequency."
G.Galimberti, et al. Expires September 18, 2016 [Page 18]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
::= { optIfXcvrMibModule 1 }
END
7. Relationship to Other MIB Modules
7.1. Relationship to the [TEMPLATE TODO] MIB
7.2. MIB modules required for IMPORTS
8. Definitions
[TEMPLATE TODO]: put your valid MIB module here.
A list of tools that can help automate the process of
checking MIB definitions can be found at
http://www.ops.ietf.org/mib-review-tools.html
9. Security Considerations
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
G.Galimberti, et al. Expires September 18, 2016 [Page 19]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
10. IANA Considerations
Option #1:
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
sampleMIB { mib-2 XXX }
Option #2:
Editor's Note (to be removed prior to publication): the IANA is
requested to assign a value for "XXX" under the 'mib-2' subtree and
to record the assignment in the SMI Numbers registry. When the
assignment has been made, the RFC Editor is asked to replace "XXX"
(here and in the MIB module) with the assigned value and to remove
this note.
Note well: prior to official assignment by the IANA, an internet
draft MUST use place holders (such as "XXX" above) rather than actual
numbers. See RFC4181 Section 4.5 for an example of how this is done
in an internet draft MIB module.
Option #3:
This memo includes no request to IANA.
11. Contributors
G.Galimberti, et al. Expires September 18, 2016 [Page 20]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Arnold Mattheus
Deutsche Telekom
Darmstadt
Germany
email a.mattheus@telekom.de
Manuel Paul
Deutsche Telekom
Berlin
Germany
email Manuel.Paul@telekom.de
Frank Luennemann
Deutsche Telekom
Munster
Germany
email Frank.Luennemann@telekom.de
Scott Mansfield
Ericsson Inc.
email scott.mansfield@ericsson.com
Najam Saquib
Cisco
Ludwig-Erhard-Strasse 3
ESCHBORN, HESSEN 65760
GERMANY
email nasaquib@cisco.com
Walid Wakim
Cisco
9501 Technology Blvd
ROSEMONT, ILLINOIS 60018
UNITED STATES
email wwakim@cisco.com
Ori Gerstel
Sedona System
ISRAEL
email orig@sedonasys.com
12. References
12.1. Normative References
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000,
<http://www.rfc-editor.org/info/rfc2863>.
G.Galimberti, et al. Expires September 18, 2016 [Page 21]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578,
DOI 10.17487/RFC2578, April 1999,
<http://www.rfc-editor.org/info/rfc2578>.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, DOI 10.17487/RFC2579, April 1999,
<http://www.rfc-editor.org/info/rfc2579>.
[RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Conformance Statements for SMIv2",
STD 58, RFC 2580, DOI 10.17487/RFC2580, April 1999,
<http://www.rfc-editor.org/info/rfc2580>.
[RFC3591] Lam, H-K., Stewart, M., and A. Huynh, "Definitions of
Managed Objects for the Optical Interface Type", RFC 3591,
DOI 10.17487/RFC3591, September 2003,
<http://www.rfc-editor.org/info/rfc3591>.
[RFC6205] Otani, T., Ed. and D. Li, Ed., "Generalized Labels for
Lambda-Switch-Capable (LSC) Label Switching Routers",
RFC 6205, DOI 10.17487/RFC6205, March 2011,
<http://www.rfc-editor.org/info/rfc6205>.
[I-D.kdkgall-ccamp-dwdm-if-mng-ctrl-fwk]
Kunze, R., Grammel, G., Beller, D., and G. Galimberti, "A
framework for Management and Control of G.698.2 optical
interface parameters", draft-kdkgall-ccamp-dwdm-if-mng-
ctrl-fwk-00 (work in progress), October 2015.
[ITU.G698.2]
International Telecommunications Union, "Amplified
multichannel dense wavelength division multiplexing
applications with single channel optical interfaces",
ITU-T Recommendation G.698.2, November 2009.
[ITU.G709]
International Telecommunications Union, "Interface for the
Optical Transport Network (OTN)", ITU-T Recommendation
G.709, February 2012.
G.Galimberti, et al. Expires September 18, 2016 [Page 22]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
[ITU.G872]
International Telecommunications Union, "Architecture of
optical transport networks", ITU-T Recommendation G.872
and Amd.1, October 2012.
[ITU.G798]
International Telecommunications Union, "Characteristics
of optical transport network hierarchy equipment
functional blocks", ITU-T Recommendation G.798 and Amd.1,
December 2012.
[ITU.G874]
International Telecommunications Union, "Management
aspects of optical transport network elements",
ITU-T Recommendation G.874, August 2013.
[ITU.G874.1]
International Telecommunications Union, "Optical transport
network (OTN): Protocol-neutral management information
model for the network element view", ITU-T Recommendation
G.874.1, October 2012.
[ITU.G959.1]
International Telecommunications Union, "Optical transport
network physical layer interfaces", ITU-T Recommendation
G.959.1, November 2009.
[ITU.G826]
International Telecommunications Union, "End-to-end error
performance parameters and objectives for international,
constant bit-rate digital paths and connections",
ITU-T Recommendation G.826, November 2009.
[ITU.G8201]
International Telecommunications Union, "Error performance
parameters and objectives for multi-operator international
paths within the Optical Transport Network (OTN)",
ITU-T Recommendation G.8201, April 2011.
[ITU.G694.1]
International Telecommunications Union, "Spectral grids
for WDM applications: DWDM frequency grid",
ITU-T Recommendation G.694.1, February 2012.
[ITU.G7710]
International Telecommunications Union, "Common equipment
management function requirements", ITU-T Recommendation
G.7710, February 2012.
G.Galimberti, et al. Expires September 18, 2016 [Page 23]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
12.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410,
DOI 10.17487/RFC3410, December 2002,
<http://www.rfc-editor.org/info/rfc3410>.
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
DOI 10.17487/RFC2629, June 1999,
<http://www.rfc-editor.org/info/rfc2629>.
[RFC4181] Heard, C., Ed., "Guidelines for Authors and Reviewers of
MIB Documents", BCP 111, RFC 4181, DOI 10.17487/RFC4181,
September 2005, <http://www.rfc-editor.org/info/rfc4181>.
[RFC4054] Strand, J., Ed. and A. Chiu, Ed., "Impairments and Other
Constraints on Optical Layer Routing", RFC 4054,
DOI 10.17487/RFC4054, May 2005,
<http://www.rfc-editor.org/info/rfc4054>.
Appendix A. Change Log
This optional section should be removed before the internet draft is
submitted to the IESG for publication as an RFC.
Note to RFC Editor: please remove this appendix before publication as
an RFC.
Appendix B. Open Issues
Note to RFC Editor: please remove this appendix before publication as
an RFC.
Authors' Addresses
Gabriele Galimberti (editor)
Cisco
Via Santa Maria Molgora, 48 c
20871 - Vimercate
Italy
Phone: +390392091462
Email: ggalimbe@cisco.com
G.Galimberti, et al. Expires September 18, 2016 [Page 24]
Internet-Draft draft-galikunze-ccamp-dwdm-if-snmp-mib-01 March 2016
Ruediger Kunze (editor)
Deutsche Telekom
Dddd, xx
Berlin
Germany
Phone: +49xxxxxxxxxx
Email: RKunze@telekom.de
Hing-Kam Lam (editor)
Alcatel-Lucent
600-700 Mountain Avenue, Murray Hill
New Jersey, 07974
USA
Phone: +17323313476
Email: kam.lam@alcatel-lucent.com
Dharini Hiremagalur (editor)
Juniper
1194 N Mathilda Avenue
Sunnyvale - 94089 California
USA
Phone: +1408
Email: dharinih@juniper.net
Luyuan Fang (editor)
Microsoft
5600 148th Ave NE
Redmond, WA 98502
USA
Email: lufang@microsoft.com
Gary Ratterree (editor)
Microsoft
5600 148th Ave NE
Redmond, WA 98502
USA
Email: gratt@microsoft.com
G.Galimberti, et al. Expires September 18, 2016 [Page 25]