Internet Engineering Task Force . G.Galimberti, Ed.
Internet-Draft Cisco
Intended status: Standards Track . R.Kunze, Ed.
Expires: April 23, 2014 Deutsche Telekom
. Kam Lam, Ed.
Alcatel-Lucent
. D. Hiremagalur, Ed.
Juniper
October 20, 2013
An SNMP MIB extension to RFC3591 to manage optical interface parameters
of DWDM applications
draft-galikunze-ccamp-g-698-2-snmp-mib-04
Abstract
This memo defines a module of the Management Information Base (MIB)
used by Simple Network Management Protocol (SNMP) in TCP/IP- based
internet. In particular, it defines objects for managing Optical
parameters associated with Dense Wavelength Division Multiplexing
(DWDM) interfaces. This is an extension of the RFC3591 to support
the optical parameters described in ITU-T G.698.2. [ITU.G698.2]
The MIB module defined in this memo can be used for Optical
Parameters monitoring and/or configuration of the endpoints of Black
Links.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
G.Galimberti, et al. Expires April 23, 2014 [Page 1]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
This Internet-Draft will expire on April 23, 2014.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . 4
3. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.1. Optical Parameters Description . . . . . . . . . . . . . 5
4.1.1. Rs-Ss Configuration . . . . . . . . . . . . . . . . . 6
4.1.2. Table of Application Codes . . . . . . . . . . . . . 7
4.1.3. Table of Vendor Application Codes . . . . . . . . . . 7
4.2. Use of ifTable . . . . . . . . . . . . . . . . . . . . . 8
4.2.1. Use of ifTable for OPS Layer . . . . . . . . . . . . 10
4.2.2. Use of ifTable for OCh Layer . . . . . . . . . . . . 11
4.2.3. Use of ifStackTable . . . . . . . . . . . . . . . . . 11
5. Structure of the MIB Module . . . . . . . . . . . . . . . . . 12
6. Object Definitions . . . . . . . . . . . . . . . . . . . . . 12
7. Relationship to Other MIB Modules . . . . . . . . . . . . . . 19
7.1. Relationship to the [TEMPLATE TODO] MIB . . . . . . . . . 19
7.2. MIB modules required for IMPORTS . . . . . . . . . . . . 19
8. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 19
9. Security Considerations . . . . . . . . . . . . . . . . . . . 19
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20
11. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 21
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 22
12.1. Normative References . . . . . . . . . . . . . . . . . . 22
12.2. Informative References . . . . . . . . . . . . . . . . . 24
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 24
Appendix B. Open Issues . . . . . . . . . . . . . . . . . . . . 24
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 24
G.Galimberti, et al. Expires April 23, 2014 [Page 2]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
used by Simple Network Management Protocol (SNMP) in TCP/IP- based
internets. In particular, it defines objects for managing Optical
parameters associated with Wavelength Division Multiplexing (WDM)
systems in accordance with the optical interface defined in G.698.2
[ITU.G698.2]
Black Link approach allows supporting an optical transmitter/receiver
pair of one vendor to inject a DWDM channel and run it over an
optical network composed of amplifiers, filters, add-drop
multiplexers from a different vendor. From architectural point of
view, the "Black Link" is a set of pre-configured/qualified network
connections between the G.698.2 reference points S and R. The black
links will be managed at the edges (i.e. the transmitters and
receivers attached to the S and R reference points respectively) for
the relevant parameters specified in G.698.2 [ITU.G698.2], G.798
[ITU.G798], G.874 [ITU.G874], and the performance parameters
specified G.7710/Y.1701 [ITU-T G.7710] and and G.874.1 [ITU.G874.1].
The G.698.2 [ITU.G698.2] provides optical parameter values for
physical layer interfaces of Dense Wavelength Division Multiplexing
(DWDM) systems primarily intended for metro applications which
include optical amplifiers. Applications are defined in G.698.2
[ITU.G698.2] using optical interface parameters at the single-channel
connection points between optical transmitters and the optical
multiplexer, as well as between optical receivers and the optical
demultiplexer in the DWDM system. This Recommendation uses a
methodology which does not specify the details of the optical link,
e.g. the maximum fibre length, explicitly. The Recommendation
currently includes unidirectional DWDM applications at 2.5 and 10
Gbit/s (with 100 GHz and 50 GHz channel frequency spacing). Work is
still underway for 40 and 100 Gbit/s interfaces. There is
possibility for extensions to a lower channel frequency spacing.
This document specifically refers to the "application code" defined
in the G.698.2 [ITU.G698.2] plus few optical paramenter not included
in the application code definition.
This draft refers and supports also the draft-kunze-g-698-2
-management-control-framework
G.Galimberti, et al. Expires April 23, 2014 [Page 3]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
The building of an SNMP MIB describing the optical parameters defined
in G.698.2 [ITU.G698.2] G.798 [ITU.G798], G.874 [ITU.G874],
parameters specified G.7710/Y.1701 [ITU-T G.7710] allows the
different vendors and operator to retrieve, provision and exchange
information related to Optical blak links in a standardized way.
This facilitates interworking in case of using optical interfaces
from different vendors at the end of the link.
The MIB, reporting the Optical parameters and their values,
characterizes the features and the performances of the optical
components and allow a reliable black link design in case of
multivendor optical networks.
Although RFC 3591 [RFC3591] describes and defines the SNMP MIB of a
number of key optical parameters, alarms and Performance Monitoring,
a more complete description of optical parameters and processes can
be found in the ITU-T Recommendations. Appendix A of this document
provides an overview about the extensive ITU-T documentation in this
area. The same considerations can be applied to the RFC 4054
[RFC4054]
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
3. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119] In
the description of OIDs the convention: Set (S) Get (G) and Trap (T)
conventions will describe the action allowed by the parameter.
4. Overview
Figure 1 shows a set of reference points, for the linear "black link"
approach, for single-channel connection (Ss and Rs) between
G.Galimberti, et al. Expires April 23, 2014 [Page 4]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
transmitters (Tx) and receivers (Rx). Here the DWDM network elements
include an OM and an OD (which are used as a pair with the opposing
element), one or more optical amplifiers and may also include one or
more OADMs.
+-------------------------------------------------+
Ss | DWDM Network Elements | Rs
+---+ | | | \ / | | | +--+
Tx L1----|->| \ +------+ +------+ / |--|-->Rx L1
+---+ | | | | | +------+ | | | | | +--+
+---+ | | | | | | | | | | | | +--+
Tx L2----|->| OM |-->|------|->| OADM |--|------|->| OD |--|-->Rx L2
+---+ | | | | | | | | | | | | +--+
+---+ | | | | | +------+ | | | | | +--+
Tx L3----|->| / | DWDM | | ^ | DWDM | \ |--|-->Rx L3
+---+ | | / | Link +----|--|----+ Link | \ | | +--+
+-----------+ | | +----------+
+--+ +--+
| |
Rs v | Ss
+-----+ +-----+
|RxLx | |TxLx |
+-----+ +-----+
Ss = reference point at the DWDM network element tributary output
Rs = reference point at the DWDM network element tributary input
Lx = Lambda x
OM = Optical Mux
OD = Optical Demux
OADM = Optical Add Drop Mux
from Fig. 5.1/G.698.2
Figure 1: Linear Black Link
G.698.2 [ITU.G698.2] defines also Ring Black Link configurations
[Fig. 5.2/G.698.2] and Bidirectional Black Link configurations [Fig.
5.3/G.698.2]
4.1. Optical Parameters Description
The black links are managed at the edges, i.e. at the transmitters
(Tx) and receivers (Rx) attached to the S and R reference points
respectively. The parameters that could be managed at the black link
edges are specified in G.698.2 [ITU.G698.2] section 5.3 referring the
"application code" notation
G.Galimberti, et al. Expires April 23, 2014 [Page 5]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
The definitions of the optical parameters are provided below to
increase the readability of the document, where the definition is
ended by (G) the parameter can be retrieve with a GET, when (S) it
can be provisioned by a SET, (G,S) can be either GET and SET.
To support the management of these parameters, the SNMP MIB in RFC
3591 [RFC3591] is extended with a new MIB module defined in section 6
of this document. This new MIB module includes the definition of new
configuration table of the OCh Layer for the parameters at Tx (S) and
Rx (R).
4.1.1. Rs-Ss Configuration
The Rs-Ss configuration table allows configuration of Wavelength,
Power and Application codes as described in [ITU.G698.2] and G.694.1
[ITU.G694.1]
This parameter report the current Transceiver Output power, it can be
either a setting and measured value (G, S) NEED TO DISCUSS ON THIS.
Wavelength Value (see G.694.1 Table 1):
This parameter indicates the wavelength value that Ss and Rs will
be set to work (in THz) se in particular Section 6/G.694.1 (G, S).
Number of Vendor Transceiver Class Supported
This parameter indicates the number of Vendor Transceiver codes
supported by this interface (G).
Single-channel application codes (see G.698.2):
This parameter indicates the transceiver application code at Ss
and Rs as defined in [ITU.G698.2] Chapter 5.4 - this parameter can
be called Optical Interface Identifier OII as per [draft-
martinelli-wson-interface-class] (G).
Number of Single-channel application codes Supported
This parameter indicates the number of Single-channel application
codes supported by this interface (G).
Current Laser Output power:
This parameter report the current Transceiver Output power, it can
be either a setting and measured value (G, S).
Minimum Laser Output power:
This parameter report the minimum Transceiver Output power
supported by this interface (G).
Maximum Laser Output power:
This parameter report the maximum Transceiver Output power
supported by this interface (G).
G.Galimberti, et al. Expires April 23, 2014 [Page 6]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
Current Laser Input power:
This parameter report the current Transceiver Input power (G).
Minimum Laser Intput power:
This parameter report the minimum Transceiver Input power
supported by this interface (G).
Maximum Laser Intput power:
This parameter report the maximum Transceiver Input power
supported by this interface (G).
+--------------------------------------+-----------+----------------+
| PARAMETERS | Get/Set | Reference |
+--------------------------------------+-----------+----------------+
| Wavelength Value | G,S | G.694.1 S.6 |
| Vendor Transceiver Class | G | N.A. |
| Number of Vendor Transceiver Class | G | N.A. |
| Supported | | |
| Single-channel application codes | G | G.698.2 S.5.3 |
| Number of Single-channel application | G | N.A. |
| codes Supported | | |
| Current Output Power | G,S | N.A. |
| Minimum Output Power | G | N.A. |
| Maximum Output Power | G | N.A. |
| Current Input Power | G | N.A. |
| Minimum Input Power | G | N.A. |
| Maximum Input Power | G | N.A. |
+--------------------------------------+-----------+----------------+
Table 1: Rs-Ss Configuration
4.1.2. Table of Application Codes
This table has a list of Application codes supported by this
interface at point R are defined in G.698.2.
Application code Identifier:
The Identifier for the Application code.
Application code:
This is the application code that is defined in G.698.2.
4.1.3. Table of Vendor Application Codes
This table has a list of Application codes supported by this
interface at point R are defined in G.698.2.
G.Galimberti, et al. Expires April 23, 2014 [Page 7]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
Vendor Transceiver Class::
The Identifier for the vendor transceiver class.
Vendor Transceiver Class:
Other than specifying all the Transceiver parameter, it might be
convenient for the vendors to summarize a set of parameters in a
single proprietary parameter: the Class of transceiver. The
Transceiver classification will be based on the Vendor Name and
the main TX and RX parameters (i.e. Trunk Mode, Framing, Bit rate,
Trunk Type, Channel Band, Channel Grid, Modulation Format, Channel
Modulation Format, FEC Coding, Electrical Signal Framing at Tx,
Minimum maximum Chromatic Disperion (CD) at Rx, Maximum
Polarization Mode Dispersion (PMD) at Rx, Maximum differential
group delay at Rx, Loopbacks, TDC, Pre-FEC BER, Q-factor,
Q-margin,etc.). If this parameter is used, the MIB parameters
specifying the Transceiver characteristics may not be significant
and the vendor will be responsible to specify the Class contents
and values. The Vendor can publish the parameters of its Classes
or declare to be compatible with published Classes.(G) Optional
for compliance. (not mentioned in G.698)
4.2. Use of ifTable
This section specifies how the MIB II interfaces group, as defined in
RFC 2863 [RFC2863], is used for the link ends of a black link. Only
the ifGeneralInformationGroup will be supported for the ifTable and
the ifStackTable to maintain the relationship between the OCh and OPS
layers. The OCh and OPS layers are managed in the ifTable using
IfEntries that correlate to the layers depicted in Figure 1.
For example, a device with TX and/or RX will have an Optical Physical
Section (OPS) layer, and an Optical Channel (OCh) layer. There is a
one to n relationship between the OPS and OCh layers.
EDITOR NOTE: Reason for changing from OChr to OCh: Work on revised
G.872 in the SG15 December 2011 meeting agreed to remove OChr from
the architecture and to update G.709 to account for this
architectural change. The meeting also agreed to consent the revised
text of G.872 and G.709 at the September 2012 SG15 meeting.
Figure 2 In the following figures, opticalChannel and
opticalPhysicalSection are abbreviated as och and ops respectively.
G.Galimberti, et al. Expires April 23, 2014 [Page 8]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
_____________________
\
Path Data Unit |\
(ODUk) | \
_____________________| \ __________________
| | | >
Tandem Data Unit | | | |
(ODUkT) | | OCh Layer | > n och IfEntries
_____________________| | | |
| |__________________| >
Optical | /| | >
Transport Unit | / | | |
(OTUk) |/ | OPSn Layer | > m ops IfEntries
_____________________/ | | |
|__________________| >
Sub-layers in
the OCh Layer
Figure 2: OTN Layers for OPS and OCh
Each opticalChannel IfEntry is mapped to one of the m
opticalPhysicalSection IfEntries, where m is greater than or equal to
1. Conversely, each opticalTransPhysicalSection port entry is mapped
to one of the n opticalChannel IfEntries, where n is greater than or
equal to 1.
The design of the Optical Interface MIB provides the option to model
an interface either as a single bidirectional object containing both
sink and source functions or as a pair of unidirectional objects, one
containing sink functions and the other containing source functions.
If the sink and source for a given protocol layer are to be modelled
as separate objects, then there need to be two ifTable entries, one
that corresponds to the sink and one that corresponds to the source,
where the directionality information is provided in the configuration
tables for that layer via the associated Directionality objects. The
agent is expected to maintain consistent directionality values
between ifStackTable layers (e.g., a sink must not be stacked in a
1:1 manner on top of a source, or vice-versa), and all protocol
layers that are represented by a given ifTable entry are expected to
have the same directionality.
When separate ifTable entries are used for the source and sink
functions of a given physical interface, association between the two
uni-directional ifTable entries (one for the source function and the
other for the sink functions) should be provided. It is recommended
G.Galimberti, et al. Expires April 23, 2014 [Page 9]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
that identical ifName values are used for the two ifTable entries to
indicate such association. An implementation shall explicitly state
what mechanism is used to indicate the association, if ifName is not
used.
4.2.1. Use of ifTable for OPS Layer
Only the ifGeneralInformationGroup needs to be supported.
ifTable Object Use for OTN OPS Layer
=====================================================================
ifIndex The interface index.
ifDescr Optical Transport Network (OTN) Optical
Physical Section (OPS)
ifType opticalPhysicalSection (xxx)
<<<Editor Note: Need new IANA registration value for xxx. >>>
ifSpeed Actual bandwidth of the interface in bits per
second. If the bandwidth of the interface is
greater than the maximum value of 4,294,967,295,
then the maximum value is reported and
ifHighSpeed must be used to report the
interface's speed.
ifPhysAddress An octet string with zero length. (There is
no specific address associated with the
interface.)
ifAdminStatus The desired administrative state of the
interface. Supports read-only access.
ifOperStatus The operational state of the interface. The
value lowerLayerDown(7) is not used, since
there is no lower layer interface. This object
is set to notPresent(6) if a component is
missing, otherwise it is set to down(2) if
either of the objects optIfOPSnCurrentStatus
indicates that any defect is present.
ifLastChange The value of sysUpTime at the last change in
ifOperStatus.
ifName Enterprise-specific convention (e.g., TL-1 AID)
G.Galimberti, et al. Expires April 23, 2014 [Page 10]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
to identify the physical or data entity
associated with this interface or an
OCTET STRING of zero length. The
enterprise-specific convention is intended to
provide the means to reference one or more
enterprise-specific tables.
ifLinkUpDownTrapEnable Default value is enabled(1). Supports
read-only access.
ifHighSpeed Actual bandwidth of the interface in Mega-bits
per second. A value of n represents a range of
'n-0.5' to 'n+0.499999'.
ifConnectorPresent Set to true(1).
ifAlias The (non-volatile) alias name for this interface
as assigned by the network manager.
4.2.2. Use of ifTable for OCh Layer
Use of ifTable for OCh Layer See RFC 3591 [RFC3591] section 2.4
4.2.3. Use of ifStackTable
Use of the ifStackTable and ifInvStackTable to associate the
opticalPhysicalSection and opticalChannel interface entries is best
illustrated by the example shown in Figure 3. The example assumes an
ops interface with ifIndex i that carries two multiplexed OCh
interfaces with ifIndex values of j and k, respectively. The example
shows that j and k are stacked above (i.e., multiplexed into) i.
Furthermore, it shows that there is no layer lower than i and no
layer higher than j and/or k.
G.Galimberti, et al. Expires April 23, 2014 [Page 11]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
Figure 3
HigherLayer LowerLayer
--------------------------
0 j
0 k
j i
k i
i 0
Figure 3: Use of ifStackTable for an OTN port
For the inverse stack table, it provides the same information as the
interface stack table, with the order of the Higher and Lower layer
interfaces reversed.
5. Structure of the MIB Module
EDITOR NOTE:text will be provided based on the MIB module in
Section 6
6. Object Definitions
EDITOR NOTE: Once the scope in Section 1 and the parameters in
Section 4 are finalized, a MIB module will be defined. It could be
an extension to the OPT-IF-MIB module of RFC 3591. >>>
OPT-IF-698-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32,
Integer32,
Unsigned32,
Counter64,
transmission,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
RowPointer,
RowStatus,
TruthValue,
DisplayString,
DateAndTime
G.Galimberti, et al. Expires April 23, 2014 [Page 12]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
optIfMibModule
FROM OPT-IF-MIB;
-- This is the MIB module for the optical parameters -
-- Application codes associated with the black link end points.
optIfXcvrMibModule MODULE-IDENTITY
LAST-UPDATED "201204250000Z"
ORGANIZATION "IETF Ops/Camp MIB Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/
Mailing Lists:
Editor: Gabriele Galimberti
Email: ggalimbe@cisco.com"
DESCRIPTION
"The MIB module to describe Black Link tranceiver
characteristics to rfc3591.
Copyright (C) The Internet Society (2012). This version
of this MIB module is part of ; see the RFC
itself for full legal notices."
REVISION "201305050000Z"
DESCRIPTION
"Draft version 1.0"
REVISION "201305050000Z"
DESCRIPTION
"Draft version 2.0"
REVISION "201302270000Z"
DESCRIPTION
"Draft version 3.0"
REVISION "201307020000Z"
DESCRIPTION
"Mib has in application code/vendor transcievercode G.698."
::= { optIfMibModule 4 }
G.Galimberti, et al. Expires April 23, 2014 [Page 13]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
-- Addition to the RFC 3591 objects
optIfOChSsRsGroup OBJECT IDENTIFIER ::= { optIfXcvrMibModule 1 }
-- OCh Ss/Rs config table
-- The application code/vendor tranceiver class for the Black Link
-- Ss-Rs will be added to the OchConfigTable
optIfOChSsRsConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSsRsConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Och General config extension parameters"
::= { optIfOChSsRsGroup 1 }
optIfOChSsRsConfigEntry OBJECT-TYPE
SYNTAX OptIfOChSsRsConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains G.698 parameters for an
interface."
INDEX { ifIndex }
::= { optIfOChSsRsConfigTable 1 }
OptIfOChSsRsConfigEntry ::=
SEQUENCE {
optIfOChWavelengthn Unsigned32,
optIfOChInterfaceVendorTransceiverClass DisplayString,
optIfOChNumberVendorClassesSupported Unsigned32,
optIfOChInterfaceApplicationCode DisplayString,
optIfOChNumberApplicationCodesSupported Unsigned32,
optIfOChOutputPower Integer32,
optIfOChMinOutputPower Integer32,
optIfOChMaxOutputPower Integer32,
optIfOChInputPower Integer32,
optIfOChMinInputPower Integer32,
optIfOChMaxInputPower Integer32
G.Galimberti, et al. Expires April 23, 2014 [Page 14]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
}
optIfOChWavelengthn OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" This parameter indicate minimum wavelength spectrum - n, in
a definite wavelength Band (L, C and S) as represented in
[RFC6205] by the formula -
Wavelength (nm ) = 1471nm + n* optIfOChMiminumChannelSpacing
(converted to nm)
Eg - optIfOChMiminumChannelSpacing in nm
'Wavelength (nm ) = 1471nm + n* 20nm (20nm is the spacing
for CWDM)'
"
::= { optIfOChSsRsConfigEntry 1 }
optIfOChInterfaceVendorTransceiverClass OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"As defined in G.698
Vendors can summarize a set of parameters in a
single proprietary parameter: the Class of transceiver. The
Transceiver classification will be based on the Vendor Name
and the main TX and RX parameters (i.e. Trunk Mode, Framing,
Bit rate, Trunk Type etc).
This defines the tranceiver class that is/should be used by
this interface. The optIfOChSrcVendorTranscieverClassTable
has all the vendor classes supported by this interface."
::= { optIfOChSsRsConfigEntry 2 }
optIfOChNumberVendorClassesSupported OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Number of Vedor classes supported by this interface."
::= { optIfOChSsRsConfigEntry 3 }
optIfOChInterfaceApplicationCode OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
G.Galimberti, et al. Expires April 23, 2014 [Page 15]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
"This parameter indicates the transceiver application code at
Ss and Rs as defined in [ITU.G698.2] Chapter 5.3, that
is/should be used by this interface. The
optIfOChSrcApplicationCodeTable has all the application
codes supported by this interface. "
::= { optIfOChSsRsConfigEntry 4 }
optIfOChNumberApplicationCodesSupported OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Number of Application codes supported by this interface."
::= { optIfOChSsRsConfigEntry 5 }
optIfOChOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The output power for this interface in .01 dbm "
::= { optIfOChSsRsConfigEntry 6 }
optIfOChMinOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The minimum output power for this interface in .01 dbm "
::= { optIfOChSsRsConfigEntry 7 }
optIfOChInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The input power for this interface in .01 dbm "
::= { optIfOChSsRsConfigEntry 8 }
optIfOChMinInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
G.Galimberti, et al. Expires April 23, 2014 [Page 16]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
" The minimum input power for this interface in .01 dbm "
::= { optIfOChSsRsConfigEntry 9 }
optIfOChMaxInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The maximum input power for this interface in .01 dbm "
::= { optIfOChSsRsConfigEntry 10 }
-- Table of Application codes supported by the interface
-- OptIfOChSrcApplicationCodeEntry
optIfOChSrcApplicationCodeTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSrcApplicationCodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Table of Application codes supported by this interface."
::= { optIfOChSsRsGroup 2 }
optIfOChSrcApplicationCodeEntry OBJECT-TYPE
SYNTAX OptIfOChSrcApplicationCodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the Application code for this
interface."
INDEX { ifIndex, optIfOChApplicationCodeNumber }
::= { optIfOChSrcApplicationCodeTable 1 }
OptIfOChSrcApplicationCodeEntry ::=
SEQUENCE {
optIfOChApplicationCodeNumber Integer32,
optIfOChApplicationCode DisplayString
}
optIfOChApplicationCodeNumber OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" The number of the application code supported at this
interface. The interface can support more than one
application codes.
G.Galimberti, et al. Expires April 23, 2014 [Page 17]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
"
::= { optIfOChSrcApplicationCodeEntry 1}
optIfOChApplicationCode OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The application code supported by this interface DWDM
link."
::= { optIfOChSrcApplicationCodeEntry 2}
-- Table of Vendor Transceiver class supported by the interface
-- OptIfOChSrcVendorTranscieverClassEntry
optIfOChSrcVendorTranscieverClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSrcVendorTranscieverClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh Src (Ss) tranceiver classes supported by
this interface."
::= { optIfOChSsRsGroup 3 }
optIfOChSrcVendorTranscieverClassEntry OBJECT-TYPE
SYNTAX OptIfOChSrcVendorTranscieverClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the tranceiver classes
supported by this interface."
INDEX { ifIndex, optIfOChTranscieverClassNumber }
::= { optIfOChSrcVendorTranscieverClassTable 1 }
OptIfOChSrcVendorTranscieverClassEntry ::=
SEQUENCE {
optIfOChTranscieverClassNumber Integer32,
optIfOChTranscieverClass DisplayString
}
optIfOChTranscieverClassNumber OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" The number of the application code supported at this
interface. The interface can support more than one
application codes.
G.Galimberti, et al. Expires April 23, 2014 [Page 18]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
"
::= { optIfOChSrcVendorTranscieverClassEntry 1}
optIfOChTranscieverClass OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Vendor tranceiver class supported by this interface."
::= { optIfOChSrcVendorTranscieverClassEntry 2}
-- Notifications
-- Wavelength Change Notification
optIfOChWavelengthChange NOTIFICATION-TYPE
OBJECTS { optIfOChWavelengthn }
STATUS current
DESCRIPTION
"Notification of a change in the wavelength."
::= { optIfXcvrMibModule 1 }
END
7. Relationship to Other MIB Modules
7.1. Relationship to the [TEMPLATE TODO] MIB
7.2. MIB modules required for IMPORTS
8. Definitions
[TEMPLATE TODO]: put your valid MIB module here.
A list of tools that can help automate the process of
checking MIB definitions can be found at
http://www.ops.ietf.org/mib-review-tools.html
9. Security Considerations
G.Galimberti, et al. Expires April 23, 2014 [Page 19]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
10. IANA Considerations
Option #1:
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
sampleMIB { mib-2 XXX }
Option #2:
G.Galimberti, et al. Expires April 23, 2014 [Page 20]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
Editor's Note (to be removed prior to publication): the IANA is
requested to assign a value for "XXX" under the 'mib-2' subtree and
to record the assignment in the SMI Numbers registry. When the
assignment has been made, the RFC Editor is asked to replace "XXX"
(here and in the MIB module) with the assigned value and to remove
this note.
Note well: prior to official assignment by the IANA, an internet
draft MUST use placeholders (such as "XXX" above) rather than actual
numbers. See RFC4181 Section 4.5 for an example of how this is done
in an internet draft MIB module.
Option #3:
This memo includes no request to IANA.
11. Contributors
Arnold Mattheus
Deutsche Telekom
Darmstadt
Germany
email a.mattheus@telekom.de
Manuel Paul
Deutsche Telekom
Berlin
Germany
email Manuel.Paul@telekom.de
Frank Luennemann
Deutsche Telekom
Munster
Germany
email Frank.Luennemann@telekom.de
Scott Mansfield
Ericsson Inc.
email scott.mansfield@ericsson.com
Najam Saquib
Cisco
Ludwig-Erhard-Strasse 3
ESCHBORN, HESSEN 65760
GERMANY
email nasaquib@cisco.com
Walid Wakim
G.Galimberti, et al. Expires April 23, 2014 [Page 21]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
Cisco
9501 Technology Blvd
ROSEMONT, ILLINOIS 60018
UNITED STATES
email wwakim@cisco.com
Ori Gerstel
Cisco
32 HaMelacha St., (HaSharon Bldg)
SOUTH NETANYA, HAMERKAZ 42504
ISRAEL
email ogerstel@cisco.com
12. References
12.1. Normative References
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD
58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC3591] Lam, H-K., Stewart, M., and A. Huynh, "Definitions of
Managed Objects for the Optical Interface Type", RFC 3591,
September 2003.
[RFC6205] Otani, T. and D. Li, "Generalized Labels for Lambda-
Switch-Capable (LSC) Label Switching Routers", RFC 6205,
March 2011.
[ITU.G698.2]
G.Galimberti, et al. Expires April 23, 2014 [Page 22]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
International Telecommunications Union, "Amplified
multichannel dense wavelength division multiplexing
applications with single channel optical interfaces ",
ITU-T Recommendation G.698.2, November 2009.
[ITU.G709]
International Telecommunications Union, "Interface for the
Optical Transport Network (OTN) ", ITU-T Recommendation
G.709, March 2003.
[ITU.G872]
International Telecommunications Union, "Architecture of
optical transport networks ", ITU-T Recommendation G.872,
November 2001.
[ITU.G798]
International Telecommunications Union, "Characteristics
of optical transport network hierarchy equipment
functional blocks ", ITU-T Recommendation G.798, October
2010.
[ITU.G874]
International Telecommunications Union, "Management
aspects of optical transport network elements ", ITU-T
Recommendation G.874, July 2010.
[ITU.G874.1]
International Telecommunications Union, "Optical transport
network (OTN): Protocol-neutral management information
model for the network element view ", ITU-T Recommendation
G.874.1, January 2002.
[ITU.G959.1]
International Telecommunications Union, "Optical transport
network physical layer interfaces ", ITU-T Recommendation
G.959.1, November 2009.
[ITU.G826]
International Telecommunications Union, "End-to-end error
performance parameters and objectives for international,
constant bit-rate digital paths and connections ", ITU-T
Recommendation G.826, November 2009.
[ITU.G8201]
International Telecommunications Union, "Error performance
parameters and objectives for multi-operator international
paths within the Optical Transport Network (OTN) ", ITU-T
Recommendation G.8201, April 2011.
G.Galimberti, et al. Expires April 23, 2014 [Page 23]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
[ITU.G694.1]
International Telecommunications Union, "Spectral grids
for WDM applications: DWDM frequency grid ", ITU-T
Recommendation G.694.1, June 2002.
[ITU.G7710]
International Telecommunications Union, "Common equipment
management function requirements ", ITU-T Recommendation
G.7710, May 2008.
12.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999.
[RFC4181] Heard, C., "Guidelines for Authors and Reviewers of MIB
Documents", BCP 111, RFC 4181, September 2005.
[I-D.kunze-g-698-2-management-control-framework]
Kunze, R., "A framework for Management and Control of
optical interfaces supporting G.698.2", draft-
kunze-g-698-2-management-control-framework-00 (work in
progress), July 2011.
[RFC4054] Strand, J. and A. Chiu, "Impairments and Other Constraints
on Optical Layer Routing", RFC 4054, May 2005.
Appendix A. Change Log
This optional section should be removed before the internet draft is
submitted to the IESG for publication as an RFC.
Note to RFC Editor: please remove this appendix before publication as
an RFC.
Appendix B. Open Issues
Note to RFC Editor: please remove this appendix before publication as
an RFC.
Authors' Addresses
G.Galimberti, et al. Expires April 23, 2014 [Page 24]
Internet-Draft draft-galikunze-ccamp-g-698-2-snmp-mib-04 October 2013
Gabriele Galimberti (editor)
Cisco
Via Philips,12
20052 - Monza
Italy
Phone: +390392091462
Email: ggalimbe@cisco.com
Ruediger Kunze (editor)
Deutsche Telekom
Dddd, xx
Berlin
Germany
Phone: +49xxxxxxxxxx
Email: RKunze@telekom.de
Hing-Kam Lam (editor)
Alcatel-Lucent
600-700 Mountain Avenue, Murray Hill
New Jersey, 07974
USA
Phone: +17323313476
Email: kam.lam@alcatel-lucent.com
Dharini Hiremagalur (editor)
Juniper
1194 N Mathilda Avenue
Sunnyvale - 94089 California
USA
Phone: +1408
Email: dharinih@juniper.net
G.Galimberti, et al. Expires April 23, 2014 [Page 25]