Internet Engineering Task Force . G.Galimberti, Ed.
Internet-Draft Cisco
Intended status: Standards Track . R.Kunze, Ed.
Expires: January 30, 2014 Deutsche Telekom
. Kam Lam, Ed.
Alcatel-Lucent
. D. Hiremagalur, Ed.
Juniper
July 29, 2013
An SNMP MIB extension to RFC3591 to manage optical parameters, alarms
and performance monitoring of DWDM applications
draft-galikunze-ccamp-opt-imp-snmp-mib-01
Abstract
This memo defines a module of the Management Information Base (MIB)
used by Simple Network Management Protocol (SNMP) in TCP/IP- based
internets. In particular, it defines objects for managing Optical
parameters associated with Dense Wavelength Division Multiplexing
(DWDM) interfaces or characterized by the Optical Transport Network
(OTN). This is an extension of the RFC3591 to support the optical
parameters mainly but not only described in recommendations like
ITU-T G.698.2. [ITU.G698.2]
The MIB module defined in this memo can be used for Optical
Parameters monitoring and/or configuration of the endpoints of Black
Links.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
G.Galimberti, et al. Expires January 30, 2014 [Page 1]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 30, 2014.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . 4
3. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1. Optical Parameters Description . . . . . . . . . . . . . 6
4.1.1. General . . . . . . . . . . . . . . . . . . . . . . . 6
4.1.2. Parameters at Ss . . . . . . . . . . . . . . . . . . 8
4.1.3. Optical path from point Ss to Rs . . . . . . . . . . 9
4.1.4. Interface at point Rs . . . . . . . . . . . . . . . . 11
4.1.5. Alarms and Threshold definition . . . . . . . . . . . 12
4.1.6. Performance Monitoring (PM) description . . . . . . . 13
4.1.7. Generic Parameter description . . . . . . . . . . . . 15
4.2. Use of ifTable . . . . . . . . . . . . . . . . . . . . . 15
4.2.1. Use of ifTable for OPS Layer . . . . . . . . . . . . 17
4.2.2. Use of ifTable for OCh Layer . . . . . . . . . . . . 18
4.2.3. Use of ifStackTable . . . . . . . . . . . . . . . . . 18
5. Structure of the MIB Module . . . . . . . . . . . . . . . . . 19
6. Object Definitions . . . . . . . . . . . . . . . . . . . . . 19
7. Relationship to Other MIB Modules . . . . . . . . . . . . . . 77
7.1. Relationship to the [TEMPLATE TODO] MIB . . . . . . . . . 77
7.2. MIB modules required for IMPORTS . . . . . . . . . . . . 77
8. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 77
9. Security Considerations . . . . . . . . . . . . . . . . . . . 77
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 78
G.Galimberti, et al. Expires January 30, 2014 [Page 2]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
11. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 78
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 79
12.1. Normative References . . . . . . . . . . . . . . . . . . 79
12.2. Informative References . . . . . . . . . . . . . . . . . 81
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 82
Appendix B. Open Issues . . . . . . . . . . . . . . . . . . . . 82
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 82
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
used by Simple Network Management Protocol (SNMP) in TCP/IP- based
internets. In particular, it defines objects for managing Optical
parameters associated with Wavelength Division Multiplexing (WDM)
systems or characterized by the Optical Transport Network (OTN) in
accordance with but not limited to the optical interface defined in
G.698.2 [ITU.G698.2]
This document further extend the draft-galikunze-ccamp-g-698-2-snmp-
mib-03 where the ITU-T G.698.2 "application-code" and few other
parameters described.
Black Link approach allows supporting an optical transmitter/receiver
pair of one vendor to inject a DWDM channel and run it over an
optical network composed of amplifiers, filters, add-drop
multiplexers from a different vendor. From architectural point of
view, the "Black Link" is a set of pre-configured/qualified network
connections between the G.698.2 reference points S and R. The black
links will be managed at the edges (i.e. the transmitters and
receivers attached to the S and R reference points respectively) for
the relevant parameters specified in G.698.2 [ITU.G698.2], G.798
[ITU.G798], G.874 [ITU.G874], and the performance parameters
specified G.7710/Y.1701 [ITU-T G.7710] and and G.874.1 [ITU.G874.1].
The G.698.2 [ITU.G698.2] provides optical parameter values for
physical layer interfaces of Dense Wavelength Division Multiplexing
(DWDM) systems primarily intended for metro applications which
include optical amplifiers. Applications are defined in G.698.2
[ITU.G698.2] using optical interface parameters at the single-channel
connection points between optical transmitters and the optical
multiplexer, as well as between optical receivers and the optical
demultiplexer in the DWDM system. This Recommendation uses a
methodology which does not specify the details of the optical link,
e.g. the maximum fibre length, explicitly. The Recommendation
currently includes unidirectional DWDM applications at 2.5 and 10
Gbit/s (with 100 GHz and 50 GHz channel frequency spacing). Work is
still underway for 40 and 100 Gbit/s interfaces. There is
possibility for extensions to a lower channel frequency spacing.
G.Galimberti, et al. Expires January 30, 2014 [Page 3]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
This draft refers and supports also the draft-kunze-g-698-2
-management-control-framework
The building of an SNMP MIB describing the optical parameters defined
in G.698.2 [ITU.G698.2] G.798 [ITU.G798], G.874 [ITU.G874],
parameters specified G.7710/Y.1701 [ITU-T G.7710] allows the
different vendors and operator to retrieve, provision and exchange
information related to Optical black links in a standardized way.
This facilitates interworking in case of using optical interfaces
from different vendors at the end of the link.
The MIB, reporting the Optical parameters and their values,
characterizes the features and the performances of the optical
components and allow a reliable black link design in case of
multivendor optical networks.
Although RFC 3591 [RFC3591] describes and defines the SNMP MIB of a
number of key optical parameters, alarms and Performance Monitoring,
a more complete description of optical parameters and processes can
be found in the ITU-T Recommendations. Appendix A of this document
provides an overview about the extensive ITU-T documentation in this
area. The same considerations can be applied to the RFC 4054
[RFC4054]
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
3. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119] In
the description of OIDs the convention: Set (S) Get (G) and Trap (T)
conventions will describe the action allowed by the paramenter.
G.Galimberti, et al. Expires January 30, 2014 [Page 4]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
4. Overview
In this document, the term OTN (Optical Transport Network) system is
used to describe devices that are compliant with the requirements
specified in the ITU-T Recommendations G.872 [ITU.G872], G.709
[ITU.G709] , G.798 [ITU.G798], G.874 [ITU.G874], and G.874.1
[ITU.G874.1] while refers to G.698.2 [ITU.G698.2] for the Black Link
and DWDM parameter description.
Figure 1 shows a set of reference points, for the linear "black link"
approach, for single-channel connection (Ss and Rs) between
transmitters (Tx) and receivers (Rx). Here the DWDM network elements
include an OM and an OD (which are used as a pair with the opposing
element), one or more optical amplifiers and may also include one or
more OADMs.
+-------------------------------------------------+
Ss | DWDM Network Elements | Rs
+---+ | | | \ / | || +---+
Tx L1----|->| \ +------+ +------+ / |--|->Rx L1
+---+ | | | | | +------+ | | | | | +---+
+---+ | | | | | | | | | | | | +---+
Tx L2----|->| OM |-->|------|->| OADM |--|------|->| OD |--|->Rx L2
+---+ | | | | | | | | | | | | +---+
+---+ | | | | | +------+ | | | | | +---+
Tx L3----|->| / | DWDM | | ^ | DWDM | \ |--|->Rx L3
+---+ | | / | Link +----|--|----+ Link | \ | | +---+
+-----------+ | | +----------+
+--+ +--+
| |
Rs v | Ss
+-----+ +-----+
|RxLx | |TxLx |
+-----+ +-----+
Ss = reference point at the DWDM network element tributary output
Rs = reference point at the DWDM network element tributary input
Lx = Lambda x
OM = Optical Mux
OD = Optical Demux
OADM = Optical Add Drop Mux
from Fig. 5.1/G.698.2
Figure 1: Linear Black Link
G.Galimberti, et al. Expires January 30, 2014 [Page 5]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
G.698.2 [ITU.G698.2] defines also Ring Black Link configurations
[Fig. 5.2/G.698.2] and Bidiractional Black Link configurations [Fig.
5.3/G.698.2]
4.1. Optical Parameters Description
The black links are managed at the edges, i.e. at the transmitters
(Tx) and receivers (Rx) attached to the S and R reference points
respectively. The parameters that could be managed at the black link
edges are specified in G.698.2 [ITU.G698.2] for the optical
interface, in G.798 [ITU.G798] for the equipment aspect, and in
G.7710/Y.1701 [ITU.G7710] and G.874 [ITU.G874] for fault management
and performance monitoring.
The definitions of the optical parameters are provided below to
increase the readability of the document, where the definition is
ended by (G) the parameter can be retrieve with a GET, when (S) it
can be provisioned by a SET, (G,S) can be either GET and SET.
To support the management of these parameters, the SNMP MIB in RFC
3591 [RFC3591] is extended with a new MIB module defined in section 6
of this document. This new MIB module includes the definition of new
configuration table of the OCh Layer for the parameters at Tx (S) and
Rx (R).
4.1.1. General
The following general parameters from G.698.2 [ITU.G698.2] and
G.694.1 [ITU.G694.1] provide general information at the optical
interface reference points.
Minimum channel spacing:
This is the minimum nominal difference in frequency (in GHz)
between two adjacent channels (G).
Bit rate/line coding of optical tributary signals:
Optical tributary signal class NRZ 2.5G (from nominally 622 Mbit/s
to nominally 2.67 Gbit/s) or NRZ 10G nominally 2.4 Gbit/s to
nominally 10.71 Gbit/s. (nominally 2.4 Gbit/s to nominally 10.71
Gbit/s). 40Gbit/s and 100Gbit/s are under study (G, S).
FEC Coding:
G.Galimberti, et al. Expires January 30, 2014 [Page 6]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
This parameter indicate what Forward Error Correction (FEC) code
is used at Ss and Rs (G, S) (not mentioned in G.698). EDITOR
NOTE: Need to check whether this parameter is to be put in "vendor
specific" parameter or can be a standard paramenter as defined in
G.698.2. Is this the various adaptations (FEC encoding types)
specified in G.798 clauses 12.3.1.1 (with FEC), 12.3.1.2 (without
FEC), and 12.3.1.5 (vendor-specific FEC) .
Maximum bit error ratio (BER):
This parameter indicate the maximum Bit error rate can be
supported by the application at the Receiver. In case of FEC
applications it is intended after the FEC correction (G) .
Fiber type:
Fiber type as per fibre types are chosen from those defined in
ITU-T Recs G.652, G.653, G.654 and G.655 (G,S) .
Wavelength Range (see G.694.1): [ITU.G694.1]
This parameter indicate minimum and maximum wavelength spectrum
(G) in a definite wavelength Band (L, C and S).
Wavelength Value (see G.694.1 Table 1):
This parameter indicates the wavelength value that Ss and Rs will
be set to work (in THz) se in particular Section 6/G.694.1 (G, S).
Vendor Transceiver Class:
Other than specifying all the Transceiver parameter, it might be
convenient for the vendors to summarize a set of parameters in a
single proprietary parameter: the Class of transceiver. The
Transceiver classification will be based on the Vendor Name and
the main TX and RX parameters (i.e. Trunk Mode, Framing, Bit rate,
Trunk Type, Channel Band, Channel Grid, Modulation Format, Channel
Modulation Format, FEC Coding, Electrical Signal Framing at Tx,
Minimum maximum Chromatic Disperion (CD) at Rx, Maximum
Polarization Mode Dispersion (PMD) at Rx, Maximum differential
group delay at Rx, Loopbacks, TDC, Pre-FEC BER, Q-factor,
Q-margin,etc.). If this parameter is used, the MIB parameters
specifying the Transceiver characteristics may not be significant
and the vendor will be responsible to specify the Class contents
and values. The Vendor can publish the parameters of its Classes
or declare to be compatible with published Classes.(G) Optional
for compliance. (not mentioned in G.698)
Single-channel application codes (see G.698.2):
This parameter indicates the transceiver application code at Ss
and Rs as defined in [ITU.G698.2] Chapter 5.4 - this parameter can
be called Optical Interface Identifier OII as per [draft-
martinelli-wson-interface-class] (G).
G.Galimberti, et al. Expires January 30, 2014 [Page 7]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
+------------------------------------+------------+-----------------+
| PARAMETERS | Get/Set | Reference |
+------------------------------------+------------+-----------------+
| Minimum channel spacing | G | G.698.2 S.7.1.1 |
| Bit rate/line coding of opt. trib. | G,S | G.698.2 S.7.1.2 |
| signals | | |
| FEC Coding | G,S | G.975 |
| Maximum bit error ratio (BER) | G | G.698.2 S.7.1.3 |
| Fiber type | G,S | G.698.2 S.7.1.4 |
| Wavelength Range | G | G.694.1 S.6 |
| Wavelength Value | G,S | G.694.1 S.6 |
| Vendor Transceiver Class | G | N.A. |
| Single-channel application codes | G | G.698.2 S.5.3 |
+------------------------------------+------------+-----------------+
Table 1: General parameters
4.1.2. Parameters at Ss
The following parameters for the interface at point S are defined in
G.698.2 [ITU.G698.2].
Maximum and minimum mean channel output power:
The mean launched power at Ss is the average power (in dBm) of a
pseudo-random data sequence coupled into the DWDM link. It is
defined as the rhange (Max and Min ) of the parameter (G, S)
Minimum and maximum central frequency:
The central frequency is the nominal single-channel frequency (in
THz) on which the digital coded information of the particular
optical channel is modulated by use of the NRZ line code. The
central frequencies of all channels within an application lie on
the frequency grid for the minimum channel spacing of the
application given in ITU-T Rec. G.694.1. This parameter give the
Maximum and minimum frequency interval the channel must be
modulated (G)
Maximum spectral excursion:
This is the maximum acceptable difference between the nominal
central frequency (in GHz) of the channel and the minus 15 dB
points of the transmitter spectrum furthest from the nominal
central frequency measured at point Ss. (G)
Maximum transmitter (residual) dispersion OSNR penalty (B.3/G.959.1)
[ITU.G959.1]
G.Galimberti, et al. Expires January 30, 2014 [Page 8]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Defines a reference receiver that this penalty is measured with.
Lowest OSNR at Ss with worst case (residual) dispersion minus the
Lowest OSNR at Ss with no dispersion. Lowest OSNR at Ss with no
dispersion (G)
Minimum side mode suppression ratio, Minimum channel extinction
ratio, Eye mask:
Although are defined in G.698.2 are not supported by this draft
(G).
Current Laser Output power:
This parameter report the current Transceiver Output power, it can
be either a setting and measured value (G, S) NEED TO DISCUSS ON
THIS.
+-------------------------------------+-----------+-----------------+
| PARAMETERS | Get/Set | Reference |
+-------------------------------------+-----------+-----------------+
| MAX and min mean channel output | G,S | G.698.2 S.7.2.1 |
| power | | |
| Min and MAX central frequency | G | G.698.2 S.7.2.2 |
| MAX spectral excursion | G | G.698.2 S.7.2.3 |
| MAX transmitter (residual) disper. | G | G.698.2 S.7.2.7 |
| OSNR penalty | | |
| MAX side mode suppression ratio, | G | G.698.2 S.7.2.6 |
| min channel extinction ratio, Eye | | |
| mask | | |
| Current Laser Output power | G,S | N.A. |
+-------------------------------------+-----------+-----------------+
Table 2: parameters at Ss
4.1.3. Optical path from point Ss to Rs
The following parameters for the optical path from point S and R are
defined in G.698.2 [ITU.G698.2].
Maximum and minimum (residual) chromatic dispersion:
These parameters define the maximum and minimum value of the
optical path "end to end chromatic dispersion" (in ps/nm) that the
system shall be able to tolerate. (G)
Minimum optical return loss at Ss:
These parameter defines minimum optical return loss (in dB) of the
cable plant at the source reference point (Ss), including any
connectors (G)
Maximum discrete reflectance between Ss and Rs:
G.Galimberti, et al. Expires January 30, 2014 [Page 9]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Optical reflectance is defined to be the ratio of the reflected
optical power present at a point, to the optical power incident to
that point. Control of reflections is discussed extensively in
ITU-T Rec. G.957 (G)
Maximum differential group delay:
Differential group delay (DGD) is the time difference between the
fractions of a pulse that are transmitted in the two principal
states of polarization of an optical signal. For distances
greater than several kilometres, and assuming random (strong)
polarization mode coupling, DGD in a fibre can be statistically
modelled as having a Maxwellian distribution. (G)
Maximum polarization dependent loss:
The polarization dependent loss (PDL) is the difference (in dB)
between the maximum and minimum values of the channel insertion
loss (or gain) of the black link from point SS to RS due to a
variation of the state of polarization (SOP) over all SOPs. (G)
Maximum inter-channel crosstalk:
Inter-channel crosstalk is defined as the ratio of total power in
all of the disturbing channels to that in the wanted channel,
where the wanted and disturbing channels are at different
wavelengths. The parameter specify the isolation of a link
conforming to the "black link" approach such that under the worst-
case operating conditions the inter-channel crosstalk at any
reference point RS is less than the maximum inter-channel
crosstalk value (G)
Maximum interferometric crosstalk:
This parameter places a requirement on the isolation of a link
conforming to the "black link" approach such that under the worst
case operating conditions the interferometric crosstalk at any
reference point RS is less than the maximum interferometric
crosstalk value. (G)
Maximum optical path OSNR penalty:
The optical path OSNR penalty is defined as the difference between
the Lowest OSNR at Rs and Lowest OSNR at Ss that meets the BER
requirement (G)
Maximum ripple:
Although is defined in G.698.2, this parameter is not supported by
this draft.
+-----------------------------------+-------------+-----------------+
| PARAMETERS | Get/Set | Reference |
+-----------------------------------+-------------+-----------------+
G.Galimberti, et al. Expires January 30, 2014 [Page 10]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
| MAX and min (residual) chromatic | G | G.698.2 S.7.3.2 |
| dispersion | | |
| Min optical return loss at Ss | G | G.698.2 S.7.3.3 |
| MAX discrete reflectance between | G | G.698.2 S.7.3.4 |
| Ss and Rs | | |
| MAX differential group delay | G | G.698.2 S.7.3.5 |
| MAX polarization dependent loss | G | G.698.2 S.7.3.6 |
| MAX inter-channel crosstalk | G | G.698.2 S.7.3.7 |
| MAX interferometric crosstalk | G | G.698.2 S.7.3.8 |
| MAX optical path OSNR penalty | G | G.698.2 S.7.3.9 |
| MAX ripple | G | G.698.2 S.7.3.1 |
+-----------------------------------+-------------+-----------------+
Table 3: parameters betweeen Ss and Rs
4.1.4. Interface at point Rs
The following parameters for the interface at point R are defined in
G.698.2.
4.1.4.1. Mandatory parameters
Maximum and minimum mean input power:
The maximum and minimum values of the average received power (in
dBm) at point Rs. (G)
Minimum optical signal-to-noise ratio (OSNR):
The minimum optical signal-to-noise ratio (OSNR) is the minimum
value of the ratio of the signal power in the wanted channel to
the highest noise power density in the range of the central
frequency plus and minus the maximum spectral excursion (G)
Receiver OSNR tolerance:
The receiver OSNR tolerance is defined as the minimum value of
OSNR at point Rs that can be tolerated while maintaining the
maximum BER of the application. (G)
Maximum reflectance at receiver:
Although is defined in G.698.2, this parameter is not supported by
this draft (G).
+-----------------------------------+-------------+-----------------+
| PARAMETERS | Get/Set | Reference |
+-----------------------------------+-------------+-----------------+
| MAX and min mean input power | G | G.698.2 S.7.4.1 |
| Min optical signal-to-noise ratio | G | G.698.2 S.7.4.2 |
| (OSNR) | | |
| Receiver OSNR tolerance | G | G.698.2 S.7.4.3 |
G.Galimberti, et al. Expires January 30, 2014 [Page 11]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
| MAX reflectance at receiver | G | G.698.2 S.7.4.4 |
+-----------------------------------+-------------+-----------------+
Table 4: mandatory parameters
4.1.4.2. Optional parameters
Current Chromatic Dispersion (CD):
Residual Chromatic Dispersion measuread at Rx Transceiver port
(G).
Current Optical Signal to Noise Ratio (OSNR):
Current Optical Signal to Noise Ratio (OSNR) estimated at Rx
Transceiver port (G).
Current Quality factor (Q):
"Q" factor estimated at Rx Transceiver port (G).
+-------------------------------------------+---------+-----------+
| PARAMETERS | Get/Set | Reference |
+-------------------------------------------+---------+-----------+
| Current Chromatic Dispersion (CD) | G | N.A. |
| Current Opt. Signal to Noise Ratio (OSNR) | G | N.A. |
| Current Quality factor (Q) | G | N.A. |
+-------------------------------------------+---------+-----------+
Table 5: optional parameters
4.1.5. Alarms and Threshold definition
This section describes the Alarms and the Thresholds at Ss and Rs
points according to ITU-T Recommendations G.798 [ITU.G798], G.874
[ITU.G874], and G.874.1 [ITU.G874.1].
OTN alarms defined in RFC3591:
Threshold Crossing Alert (TCA Alarm)
LOW-TXPOWER
HIGH-TXPOWER
LOW-RXPOWER
HIGH-RXPOWER
Loss of Signal (LOS)
G.Galimberti, et al. Expires January 30, 2014 [Page 12]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Loss of Frame (LOF)
Server Signal Failure-P (SSF-P)
Loss of Multiframe (LOM)
OTN Thresholds (for TCA) defined in RFC3591
LOW-TXPOWER
HIGH-TXPOWER
LOW-RXPOWER
HIGH-RXPOWER
As the above parameters/alarms are already defined in RFC3591, they
are out of scope of this document and the RFC3591 will continue to be
the only reference for them
The list below reports the new Alarms and Thresholds not managed in
RFC3591
4.1.6. Performance Monitoring (PM) description
This section describes the Performance Monitoring parameters and
their thresholds at Ss and Rs points (Near -End and Far-End)according
to ITU-T Recommendations G.826 [ITU.G826], G.8201 [ITU.G8201], G.709
[ITU.G709], G.798 [ITU.G798], G.874 [ITU.G874], and G.874.1
[ITU.G874.1].
BIP8 :
Number of BIP8's occurred in an observation periond (G). BIP-8
consists of a parity byte calculated bit-wise across a large
number of bytes in a transmission transport frame. BIP-8 bits are
set such that the overall data stream, including the BIP-8 byte,
has even parity.
Errored Second (es) :
It is a one-second period in which there is one or more errored
blocks or during which a defect (e.g. Loss of Signal (LOS)) is
detected. The number of errored seconds is summed over 15-minute
and 24-hour intervals. (G)
Severely Errored Seconds (ses) :
It is a one-second period in which the errored block ratio exceeds
a threshold or during which a defect is detected. See ITU-T
Recommendation G.8201 Table 7-1 for details. The number of
G.Galimberti, et al. Expires January 30, 2014 [Page 13]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
severely errored seconds is summed over 15-minute and 24-hour
intervals.(G)
Unavailable Seconds (uas) :
It is a one-second period in the unavailable time. A period of
unavailable time begins at the onset of ten consecutive SES
events. These ten seconds are considered to be part of
unavailable time. A new period of available time begins at the
onset of ten consecutive non-SES events. These ten seconds are
considered to be part of available time. (G)
Background Block Errors (bbe) :
An errored block not occurring as part of an SES(G)
Error Seconds Ratio (esr) :
The ratio of ES in available time to total seconds in available
time during a fixed measurement interval(G)
Severely Errored Seconds Ratio (sesr) :
The ratio of SES in available time to total seconds in available
time during a fixed measurement interval(G)
Background Block Errored Seconds Ratio (bber) :
The ratio of Background Block Errors (BBE) to total blocks in
available time during a fixed measurement interval. The count of
total blocks excludes all blocks during SESs.(G)
FEC corrected Bit Error (FECcorrErr):
The number of bits corrected by the FEC are counted over one
second (G)
FEC un-corrected Bit Error :
The number of bits un-corrected by the FEC are counted over one
second (G)
Pre-FEC Bit Error :
The number of Errored bits at receiving side before the FEC
function counted over one second (G)
OTN Valid Intervals :
The number of contiguous 15 minute intervals for which valid OTN
performance monitoring data is available for the particular
interface (G)
FEC Valid Intervals :
The number of contiguous 15 minute intervals for which valid FEC
PM data is available for the particular interface.(G)
G.Galimberti, et al. Expires January 30, 2014 [Page 14]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
4.1.7. Generic Parameter description
This section describes the Generic Parameters at Ss and Rs points
according to ITU-T Recommendations G.872 [ITU.G872], G.709
[ITU.G709], G.798 [ITU.G798], G.874 [ITU.G874], and G.874.1
[ITU.G874.1].
Interface Admin Status :
The Administrative Status of an Interface: Up/Down - In Service/
Out of Service (can be Automatic in Service) (G/S)
Interface Operational Status :
The Operational Status of an Interface: Up/Down - In Service/Out
of Service (G)
4.2. Use of ifTable
This section specifies how the MIB II interfaces group, as defined in
RFC 2863 [RFC2863], is used for the link ends of a black link. Only
the ifGeneralInformationGroup will be supported for the ifTable and
the ifStackTable to maintain the relationship between the OCh and OPS
layers. The OCh and OPS layers are managed in the ifTable using
IfEntries that correlate to the layers depicted in Figure 1.
For example, a device with TX and/or RX will have an Optical Physical
Section (OPS) layer, and an Optical Channel (OCh) layer. There is a
one to n relationship between the OPS and OCh layers.
EDITOR NOTE: Reason for changing from OChr to OCh: Work on revised
G.872 in the SG15 December 2011 meeting agreed to remove OChr from
the architecture and to update G.709 to account for this
architectural change. The meeting also agreed to consent the revised
text of G.872 and G.709 at the September 2012 SG15 meeting.
Figure 2 In the following figures, opticalChannel and
opticalPhysicalSection are abbreviated as och and ops respectively.
G.Galimberti, et al. Expires January 30, 2014 [Page 15]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
_____________________
\
Path Data Unit |\
(ODUk) | \
_____________________| \ ___________________
| | | >
Tandem Data Unit | | | |
(ODUkT) | | OCh Layer | > n och IfEntries
_____________________| | | |
| |___________________| >
Optical | /| | >
Transport Unit | / | | |
(OTUk) |/ | OPSn Layer | > m ops IfEntries
_____________________/ | | |
|___________________| >
Sub-layers in
the OCh Layer
Figure 2: OTN Layers for OPS and OCh
Each opticalChannel IfEntry is mapped to one of the m
opticalPhysicalSection IfEntries, where m is greater than or equal to
1. Conversely, each opticalTransPhysicalSection port entry is mapped
to one of the n opticalChannel IfEntries, where n is greater than or
equal to 1.
The design of the Optical Interface MIB provides the option to model
an interface either as a single bidirectional object containing both
sink and source functions or as a pair of unidirectional objects, one
containing sink functions and the other containing source functions.
If the sink and source for a given protocol layer are to be modelled
as separate objects, then there need to be two ifTable entries, one
that corresponds to the sink and one that corresponds to the source,
where the directionality information is provided in the configuration
tables for that layer via the associated Directionality objects. The
agent is expected to maintain consistent directionality values
between ifStackTable layers (e.g., a sink must not be stacked in a
1:1 manner on top of a source, or vice-versa), and all protocol
layers that are represented by a given ifTable entry are expected to
have the same directionality.
When separate ifTable entries are used for the source and sink
functions of a given physical interface, association between the two
uni-directional ifTable entries (one for the source function and the
other for the sink functions) should be provided. It is recommended
G.Galimberti, et al. Expires January 30, 2014 [Page 16]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
that identical ifName values are used for the two ifTable entries to
indicate such association. An implementation shall explicitly state
what mechanism is used to indicate the association, if ifName is not
used.
4.2.1. Use of ifTable for OPS Layer
Only the ifGeneralInformationGroup needs to be supported.
ifTable Object Use for OTN OPS Layer
====================================================================
ifIndex The interface index.
ifDescr Optical Transport Network (OTN) Optical
Physical Section (OPS)
ifType opticalPhysicalSection (xxx)
<<<Editor Note: Need new IANA registration value for xxx. >>>
ifSpeed Actual bandwidth of the interface in bits per
second. If the bandwidth of the interface is
greater than the maximum value of 4,294,967,295,
then the maximum value is reported and
ifHighSpeed must be used to report the
interface's speed.
ifPhysAddress An octet string with zero length. (There is
no specific address associated with the
interface.)
ifAdminStatus The desired administrative state of the
interface. Supports read-only access.
ifOperStatus The operational state of the interface. The
value lowerLayerDown(7) is not used, since
there is no lower layer interface. This object
is set to notPresent(6) if a component is
missing, otherwise it is set to down(2) if
either of the objects optIfOPSnCurrentStatus
indicates that any defect is present.
ifLastChange The value of sysUpTime at the last change in
ifOperStatus.
ifName Enterprise-specific convention (e.g., TL-1 AID)
G.Galimberti, et al. Expires January 30, 2014 [Page 17]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
to identify the physical or data entity
associated with this interface or an
OCTET STRING of zero length. The
enterprise-specific convention is intended to
provide the means to reference one or more
enterprise-specific tables.
ifLinkUpDownTrapEnable Default value is enabled(1). Supports
read-only access.
ifHighSpeed Actual bandwidth of the interface in Mega-bits
per second. A value of n represents a range of
'n-0.5' to 'n+0.499999'.
ifConnectorPresent Set to true(1).
ifAlias The (non-volatile) alias name for this interface
as assigned by the network manager.
4.2.2. Use of ifTable for OCh Layer
Use of ifTable for OCh Layer See RFC 3591 [RFC3591] section 2.4
4.2.3. Use of ifStackTable
Use of the ifStackTable and ifInvStackTable to associate the
opticalPhysicalSection and opticalChannel interface entries is best
illustrated by the example shown in Figure 3. The example assumes an
ops interface with ifIndex i that carries two multiplexed och
interfaces with ifIndex values of j and k, respectively. The example
shows that j and k are stacked above (i.e., multiplexed into) i.
Furthermore, it shows that there is no layer lower than i and no
layer higher than j and/or k.
G.Galimberti, et al. Expires January 30, 2014 [Page 18]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Figure 3
HigherLayer LowerLayer
--------------------------
0 j
0 k
j i
k i
i 0
Figure 3: Use of ifStackTable for an OTN port
For the inverse stack table, it provides the same information as the
interface stack table, with the order of the Higher and Lower layer
interfaces reversed.
5. Structure of the MIB Module
EDITOR NOTE:text will be provided based on the MIB module in
Section 6
6. Object Definitions
EDITOR NOTE: Once the scope in Section 1 and the parameters in
Section 4 are finalized, a MIB module will be defined. It could be
an extension to the OPT-IF-MIB module of RFC 3591. >>>
PT-IF-EXT-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32,
Integer32,
Unsigned32,
Counter64,
transmission,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
RowPointer,
RowStatus,
TruthValue,
DisplayString,
DateAndTime
G.Galimberti, et al. Expires January 30, 2014 [Page 19]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
OptIfDirectionality,
optIfOChConfigEntry,
optIfOChSinkCurrentEntry,
optIfMibModule
FROM OPT-IF-MIB;
-
-- This is the MIB module for the optical parameters associated with
-- the black link end points
-- extension for Alarms and PM
optIfExtMibModule MODULE-IDENTITY
LAST-UPDATED "201307020000Z"
ORGANIZATION "IETF Ops/Camp MIB Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/
Mailing Lists:
Editor: Gabriele Galimberti
Email: ggalimbe@cisco.com"
DESCRIPTION
"The MIB module to describe Black Link extension to rfc3591.
Copyright (C) The Internet Society (2013). This version
of this MIB module is part of ; see the RFC
itself for full legal notices."
REVISION "201307020000Z"
DESCRIPTION
" Draft version 1.0
Mib has all transceiver capabititues as described in G.698,
alarm and PM's."
::={ optIfMibModule 3 }
G.Galimberti, et al. Expires January 30, 2014 [Page 20]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
OptIfChannelSpacing ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Channel spacing
1 - 100 Ghz
2 - 50GHz
3 - 25GHz
4 - 12.5GHz
5 - 6.25Ghz
"
SYNTAX INTEGER {
spacing100Ghz(1),
spacing50Ghz(2),
spacing25Ghz(3),
spacing12point5Ghz(4),
spacing6point25Ghz(5)
}
OptIfBitRateLineCoding ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Optical tributary signal class
1 - NRZ 2.5G from nominally 622 Mbit/s to nominal 2.67 Gbit/s)
2 - NRZ 10G nominally 2.4 Gbit/s to nominally 10.71 Gbit/s.
3 - 40Gbits/s
4 - 100Gbits/s
5 - 400Gbits/s
40Gbits/s and above are under study. "
SYNTAX INTEGER {
rate2point5G(1),
rate10G(2),
rate40G(3),
rate100G(4),
rate400G(5)
}
OptIfFiberTypeRecommendation ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
" Fiber Types - ITU-T Recs G.652, G.653, G.654 and G.655
One for recommendation and one for category.
G.652 A, B, C, D
G.653 A, B
G.654 A, B, C
G.655 C, D, E
G.656
G.657 A, B
G.Galimberti, et al. Expires January 30, 2014 [Page 21]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
"
SYNTAX INTEGER {
g652(1),
g653(2),
g654(3),
g655(4),
g656(5),
g657(6)
}
OptIfFiberTypeCategory ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
" Fiber Types - ITU-T Recs G.652, G.653, G.654 and G.655
G.652 A, B, C, D
G.653 A, B
G.654 A, B, C
G.655 C, D, E
G.656
G.657 A, B
Categories - A, B, C, D and E
"
SYNTAX INTEGER {
categoryA(1),
categoryB(2),
categoryC(3),
categoryD(4),
categoryE(5)
}
OptIfGridTypes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
" The types of Grid as defined by ITU-T
"
SYNTAX INTEGER {
gridReserved(0),
gridITUDWDM(1),
gridITUCWDM(2),
gridITUFlex(4)
}
OptIfDataType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"
This parameter indicates the parameters for the table are for
the Near End or Far End data.
G.Galimberti, et al. Expires January 30, 2014 [Page 22]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
1 - Near End
2 - Far End
"
SYNTAX INTEGER {
nearEnd(1),
farEnd(2)
}
OptIfOTNLayer ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"
This parameter indicates the parameters for the table are for
OTUk, ODUk, TCM performance data.
1 - OTUk
2 - ODUk
3 - TCM
The ODUk layer and TCM sublayer PM is not related to the black
link PM management, but since this could be a common PM model
for the ODUk layer and TCM sublayers, they are included here so
it may be used for simple scenarios where only lower order ODUk
or higher order ODUk is present. For scenarios where both lower
order ODUk and higher order ODUk are present, further extension
to the MIBmodel is required, in particular for the indexing for
these layers.
"
SYNTAX INTEGER {
optIfOTUkLayer(1),
optIfODUkLayer(2),
optIfTCMSubLayer(3)
}
optIfOTNAlarmSeverity ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
" Severity of the notification.
"
SYNTAX INTEGER {
optIfCritical(1),
optIfMajor(2),
optIfMinor(3),
optIfInfo(4)
}
--
-- Alarm for the OCh and OTUk layer
--
OptIfOTNOChAlarms ::= TEXTUAL-CONVENTION
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 23]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
" This is the possible alarms from the OCh and OTUk layer."
SYNTAX INTEGER {
-- OTN Loss of signal alarm
optIfOtnLosAlarm(1),
-- OTN Loss of Frame alarm
optIfOtnLofAlarm(2),
-- OTN Loss of Multi Frame alarm
optIfOtnLomAlarm(3),
-- OTN Server Signal Failure alarm
optIfOtnOtuSsfAlarm(4),
-- OTN OTU Backward Defect Indicator alarm
optIfOtnOtuBdiAlarm(5),
-- OTN OTU Trail Trace Identifier Mismatch alarm
optIfOtnOtuTimAlarm(6),
-- OTN OTU Degraded alarm,
optIfOtnOtuDegAlarm(7),
-- OTN OTU Fec Excessive Errors alarm
optIfOptIfOtnOtuFecExcessiveErrsAlarm(8),
-- OTN OTU BBE Thresholdalarm
optIf15MinThreshBBETCA(9),
-- OTN OTU ES Thresholdalarm
optIf15MinThreshESTCA(10),
-- OTN OTU SES Threshold alarm
optIf15MinThreshSESTCA(11),
-- OTN OTU UAS Threshold alarm
optIf15MinThreshUASTCA(12),
-- OTN OTU Bip8 Threshold alarm
optIf15MinThreshBip8TCA(13),
-- OTN FEC uncorrectedwords TCA
optIf15MinThreshFECUnCorrectedWordsTCA(14),
-- OTN Pre FEC BER TCA
optIf15MinThreshPreFECBERTCA(15)
}
OptIfOTNODUkTcmAlarms ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
" This is the alarms from the ODUk and TCM layer."
SYNTAX INTEGER {
-- OTN ODU/TCM Open Connection Indicator
optIfOTNOdukTcmOciAlarm(1),
-- OTN ODU/TCM LCK
optIfOTNOdukTcmLckAlarm(2),
-- OTN ODU/TCM Backward Defect Indicator
optIfOTNOdukTcmBdiAlarm(3),
-- OTN ODU/TCM Trail Trace Identifier Mismatch
optIfOTNOdukTcmTimAlarm(4),
G.Galimberti, et al. Expires January 30, 2014 [Page 24]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
-- OTN ODU/TCM Degraded
optIfOTNOdukTcmDegAlarm(5),
-- OTN ODU/TCM LTC Loss of Tandem connection
optIfOTNOdukTcmLtcAlarm(6),
-- OTN ODU/TCM CSF - Client Signal Failure
optIfOTNOdukTcmCSfAlarm(7),
-- OTN ODU/TCM Server Signal Failure
optIfOTNOdukTcmSSfAlarm(8),
-- OTN OTU BBE Threshold
optIfOTNOdukTcm15MinThreshBBETCA(9),
-- OTN OTU ES Threshold
optIfOTNOdukTcm15MinThreshESTCA(10),
-- OTN OTU SES Threshold
optIfOTNOdukTcm15MinThreshSESTCA(11),
-- OTN OTU UAS Threshold
optIfOTNOdukTcm15MinThreshUASTCA(12)
}
-- Addition to the RFC 3591 objects
optIfOTNNotifications OBJECT IDENTIFIER ::= { optIfExtMibModule 0 }
optIfOPSmEntry OBJECT IDENTIFIER ::= { optIfExtMibModule 1 }
optIfOChXcvrGroup OBJECT IDENTIFIER ::= { optIfExtMibModule 2 }
optIfOTNPMGroup OBJECT IDENTIFIER ::= { optIfExtMibModule 3 }
optIfOTNAlarm OBJECT IDENTIFIER ::= { optIfExtMibModule 4 }
-- OPS - Optical Phyical Section
optIfOPSmConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOPSmConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OPS General config parameters."
::= { optIfOPSmEntry 1 }
optIfOPSmConfigEntry OBJECT-TYPE
SYNTAX OptIfOPSmConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An conceptual row of OPS General config parameters."
INDEX { ifIndex }
::= { optIfOPSmConfigTable 1 }
OptIfOPSmConfigEntry ::=
G.Galimberti, et al. Expires January 30, 2014 [Page 25]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SEQUENCE {
optIfOPSmDirectionality
OptIfDirectionality,
optIfOPSmFiberTypeRecommendation
OptIfFiberTypeRecommendation,
optIfOPSmFiberTypeCategory
OptIfFiberTypeCategory
}
optIfOPSmDirectionality OBJECT-TYPE
SYNTAX OptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { optIfOPSmConfigEntry 1 }
optIfOPSmFiberTypeRecommendation OBJECT-TYPE
SYNTAX OptIfFiberTypeRecommendation
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Fiber type as per fibre types are chosen from those defined
in ITU-T Recs G.652, G.653, G.654, G.655, G.656 and G.657."
::= { optIfOPSmConfigEntry 2 }
optIfOPSmFiberTypeCategory OBJECT-TYPE
SYNTAX OptIfFiberTypeCategory
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Fiber type as per fibre types are chosen from those defined
in ITU-T Recs G.652, G.653, and G.655.
The categories are A, B, C, D and E."
::= { optIfOPSmConfigEntry 3 }
-- Tranceiver general parameters table
-- General parameters for the Black Link Ss-Rs
optIfXcvrTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Och General config extension parameters"
::= { optIfOChXcvrGroup 1 }
G.Galimberti, et al. Expires January 30, 2014 [Page 26]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfXcvrEntry OBJECT-TYPE
SYNTAX OptIfXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh configuration extension
information of an interface."
AUGMENTS { optIfOChConfigEntry }
::= { optIfXcvrTable 1 }
OptIfXcvrEntry ::=
SEQUENCE {
optIfOChMiminumChannelSpacing OptIfChannelSpacing,
optIfOChBitRateLineCoding OptIfBitRateLineCoding,
optIfOChFEC Unsigned32,
optIfOChSinkMaximumBERMantissa Unsigned32,
optIfOChSinkMaximumBERExponent Unsigned32,
optIfOChMinWavelength Unsigned32,
optIfOChMaxWavelength Unsigned32
}
optIfOChMiminumChannelSpacing OBJECT-TYPE
SYNTAX OptIfChannelSpacing
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A minimum nominal difference in frequency (GHz) between two
adjacent channels."
::= { optIfXcvrEntry 1 }
optIfOChBitRateLineCoding OBJECT-TYPE
SYNTAX OptIfBitRateLineCoding
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Optical tributary signal class
NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67
Gbit/s) NRZ 10G (nominally 2.4 Gbit/s to nominally 10.71
Gbit/s) "
::= { optIfXcvrEntry 2 }
optIfOChFEC OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter indicates what Forward Error Correction
G.Galimberti, et al. Expires January 30, 2014 [Page 27]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
(FEC) code is used at Source and Sink.
GFEC (from G709) and the I.x EFEC's
(G.975 - Table I.1 super FEC).
1 - No FEC
2 - GFEC
3 - I.2 EFEC
4 - I.3 EFEC
5 - I.4 EFEC
6 - I.5 EFEC
7 - I.6 EFEC
8 - I.7 EFEC
9 - I.8 EFEC
10 - I.9 EFEC
11 - 100G FEC (for new applications)
12 - 100G EFEC (for new applications)
99 - Vendor Specific "
::= { optIfXcvrEntry 3 }
optIfOChSinkMaximumBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This parameter indicate the maximum Bit(mantissa) error
rate can be supported by the application at the Receiver.
In case of FEC applications it is intended after the FEC
correction."
::= { optIfXcvrEntry 4 }
optIfOChSinkMaximumBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This parameter indicate the maximum Bit(exponent) error
rate can be supported by the application at the Receiver.
In case of FEC applications it is intended after the FEC
correction."
::= { optIfXcvrEntry 5 }
optIfOChMinWavelength OBJECT-TYPE
SYNTAX Unsigned32
UNITS "0.01 nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This parameter indicate minimum wavelength spectrum in a
definite wavelength Band (L, C and S) "
G.Galimberti, et al. Expires January 30, 2014 [Page 28]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
::= { optIfXcvrEntry 6 }
optIfOChMaxWavelength OBJECT-TYPE
SYNTAX Unsigned32
UNITS "0.01 nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This parameter indicate maximum wavelength spectrum in a
definite wavelength Band (L, C and S) "
::= { optIfXcvrEntry 7 }
-- Tranceiver (xcvr) Parameters at OCh Src (Ss)
-- OptIfOChSrcXcvrEntry
optIfOChSrcXcvrTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSrcXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A configuration table of OCh Src (Ss) parameters."
::= { optIfOChXcvrGroup 2 }
optIfOChSrcXcvrEntry OBJECT-TYPE
SYNTAX OptIfOChSrcXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the Src (Ss) configuration
parameters for a given interface."
INDEX { ifIndex }
::= { optIfOChSrcXcvrTable 1 }
OptIfOChSrcXcvrEntry ::=
SEQUENCE {
optIfOChMinimumMeanChannelOutputPower Integer32,
optIfOChMaximumMeanChannelOutputPower Integer32,
optIfOChMinimumCentralFrequency Unsigned32,
optIfOChMaximumCentralFrequency Unsigned32,
optIfOChMaximumSpectralExcursion Unsigned32,
optIfOChMaximumTxDispersionOSNRPenalty Integer32
}
optIfOChMinimumMeanChannelOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 29]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"The minimum mean launched power at Ss is the average power
(in dbm) of a pseudo-random data sequence coupled into the
DWDM link."
::= { optIfOChSrcXcvrEntry 1}
optIfOChMaximumMeanChannelOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum mean launched power at Ss is the average power
(in dbm) of a pseudo-random data sequence coupled into the
DWDM link."
::= { optIfOChSrcXcvrEntry 2}
optIfOChMinimumCentralFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "0.01 THz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum central frequency is the nominal single-channel
frequency (in THz) on which the digital coded information of
the particular optical channel is modulated by use of the
NRZ line code. Eg 191.5THz will be represented as 19150 "
::= { optIfOChSrcXcvrEntry 3}
optIfOChMaximumCentralFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "0.01 THz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum central frequency is the nominal single-channel
frequency(in THz) on which the digital coded information of
the particular optical channel is modulated by use of the
NRZ line code. Eg 191.5THz will be represented as 19150 "
::= { optIfOChSrcXcvrEntry 4}
optIfOChMaximumSpectralExcursion OBJECT-TYPE
SYNTAX Unsigned32
UNITS "0.1 GHz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the maximum acceptable difference between the
G.Galimberti, et al. Expires January 30, 2014 [Page 30]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
nominal central frequency (in GHz) of the channel and the
minus 15 dB points of the transmitter spectrum furthest
from the nominal central frequency measured at point Ss."
::= { optIfOChSrcXcvrEntry 5}
optIfOChMaximumTxDispersionOSNRPenalty OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines a reference receiver that this penalty is measured
with. Lowest OSNR at Ss with worst case (residual)
dispersion minus the lowest OSNR at Ss with no dispersion.
Lowest OSNR at Ss with no dispersion. "
::= { optIfOChSrcXcvrEntry 6}
-- Optical Path from Point Src (Ss) to Sink (Rs)
-- Alternatively this can be optIfOChSsRsTable
optIfOChSrcSinkXcvrTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSrcSinkXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of paramters for the optical path from Src to Sink
(Ss to Rs)."
::= { optIfOChXcvrGroup 3 }
optIfOChSrcSinkXcvrEntry OBJECT-TYPE
SYNTAX OptIfOChSrcSinkXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the optical path Src-Sink
(Ss-Rs) configuration parameters for a given interface."
INDEX { ifIndex }
::= { optIfOChSrcSinkXcvrTable 1 }
OptIfOChSrcSinkXcvrEntry ::=
SEQUENCE {
optIfOChSrcSinkMinimumChromaticDispersion
Integer32,
optIfOChSrcSinkMaximumChromaticDispersion
Integer32,
optIfOChSrcSinkMinimumSrcOpticalReturnLoss
Integer32,
optIfOChSrcSinkMaximumDiscreteReflectanceSrcToSink
G.Galimberti, et al. Expires January 30, 2014 [Page 31]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Integer32,
optIfOChSrcSinkMaximumDifferentialGroupDelay
Integer32,
optIfOChSrcSinkMaximumPolarisationDependentLoss
Integer32,
optIfOChSrcSinkMaximumInterChannelCrosstalk
Integer32,
optIfOChSrcSinkInterFerometricCrosstalk
Integer32,
optIfOChSrcSinkOpticalPathOSNRPenalty
Integer32
}
optIfOChSrcSinkMinimumChromaticDispersion OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"These parameters define the minimum value of the
optical path 'end to end chromatic dispersion' (in ps/nm)
that the system shall be able to tolerate."
::= { optIfOChSrcSinkXcvrEntry 1}
optIfOChSrcSinkMaximumChromaticDispersion OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"These parameters define the maximum value of the
optical path 'end to end chromatic dispersion' (in ps/nm)
that the system shall be able to tolerate."
::= { optIfOChSrcSinkXcvrEntry 2 }
optIfOChSrcSinkMinimumSrcOpticalReturnLoss OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"These parameter defines minimum optical return loss (in dB)
of the cable plant at the source reference point (Src/Ss),
including any connectors."
::= { optIfOChSrcSinkXcvrEntry 3 }
optIfOChSrcSinkMaximumDiscreteReflectanceSrcToSink OBJECT-TYPE
SYNTAX Integer32
G.Galimberti, et al. Expires January 30, 2014 [Page 32]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Optical reflectance is defined to be the ratio of the
reflected optical power pre.sent at a point, to the optical
power incident to that point. Control of reflections is
discussed extensively in ITU-T Rec. G.957."
::= { optIfOChSrcSinkXcvrEntry 4}
optIfOChSrcSinkMaximumDifferentialGroupDelay OBJECT-TYPE
SYNTAX Integer32
UNITS "ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Differential group delay (DGD) is the time difference
between the fractions of a pulse that are transmitted in
the two principal states of polarization of an optical
signal. For distances greater than several kilometres,
and assuming random (strong) polarization mode coupling,
DGD in a fibre can be statistically modelled as having a
Maxwellian distribution."
::= { optIfOChSrcSinkXcvrEntry 5}
optIfOChSrcSinkMaximumPolarisationDependentLoss OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The polarisation dependent loss (PDL) is the difference
(in dB) between the maximum and minimum values of the
channel insertion loss (or gain) of the black-link from
point SS to RS due to a variation of the state of
polarization (SOP) over all SOPs."
::= { optIfOChSrcSinkXcvrEntry 6}
optIfOChSrcSinkMaximumInterChannelCrosstalk OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Inter-channel crosstalk is defined as the ratio of total
power in all of the disturbing channels to that in the
wanted channel, where the wanted and disturbing channels
are at different wavelengths. The parameter specify the
G.Galimberti, et al. Expires January 30, 2014 [Page 33]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
isolation of a link conforming to the 'black-link' approach
such that under the worst-case operating conditions the
inter-channel crosstalk at any reference point RS is less
than the maximum inter-channel crosstalk value."
::= { optIfOChSrcSinkXcvrEntry 7}
optIfOChSrcSinkInterFerometricCrosstalk OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This parameter places a requirement on the isolation of a
link conforming to the 'black-link' approach such that
under the worst case operating conditions the
interferometric crosstalk at any reference point RS is less
than the maximum interferometric crosstalk value.."
::= { optIfOChSrcSinkXcvrEntry 8}
optIfOChSrcSinkOpticalPathOSNRPenalty OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical path OSNR penalty is defined as the difference
between the Lowest OSNR at Rs and Lowest OSNR at Ss that
meets the BER requirement."
::= { optIfOChSrcSinkXcvrEntry 9}
-- Parameters at Sink (Rs)
-- optIfOChSinkXcvrTable
optIfOChSinkXcvrTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSinkXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh Sink (Rs) configuration parameters."
::= { optIfOChXcvrGroup 4 }
optIfOChSinkXcvrEntry OBJECT-TYPE
SYNTAX OptIfOChSinkXcvrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the Sink (Rs) configuration
parameters for a given interface."
INDEX { ifIndex }
G.Galimberti, et al. Expires January 30, 2014 [Page 34]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
::= { optIfOChSinkXcvrTable 1 }
OptIfOChSinkXcvrEntry ::=
SEQUENCE {
optIfOChSinkMinimumMeanIntputPower Integer32,
optIfOChSinkMaximumMeanIntputPower Integer32,
optIfOChSinkMinimumOSNR Integer32,
optIfOChSinkOSNRTolerance Integer32
}
optIfOChSinkMinimumMeanIntputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The minimum values of the average received power (in dbm
at point the Sink (Rs)."
::= { optIfOChSinkXcvrEntry 1}
optIfOChSinkMaximumMeanIntputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum values of the average received power (in dbm)
at point the Sink (Rs)."
::= { optIfOChSinkXcvrEntry 2}
optIfOChSinkMinimumOSNR OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum optical signal-to-noise ratio (OSNR) is the
minimum value of the ratio of the signal power in the wanted
channel to the highest noise power density in the range of
the central frequency plus and minus the maximum spectral
excursion."
::= { optIfOChSinkXcvrEntry 3}
optIfOChSinkOSNRTolerance OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 35]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"The receiver OSNR tolerance is defined as the minimum value
of OSNR at point Sink (Rs) that can be tolerated while
maintaining the maximum BER of the application. Sink (Rs)."
::= { optIfOChSinkXcvrEntry 4}
-- The OptIfOChSinkCurrentExtEntry table is an extension to the
-- optIfOChSinkCurrentExtEntry
-- following optional parameters for current status
-- OptIfOChSinkCurrentExtEntry
optIfOChSinkCurrentExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOChSinkCurrentExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh sink etxension to the performance monitoring
information for the current 15-minute interval."
::= { optIfOTNPMGroup 1 }
optIfOChSinkCurrentExtEntry OBJECT-TYPE
SYNTAX OptIfOChSinkCurrentExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh sink performance
monitoring information for an interface for the current
15-minute interval."
AUGMENTS { optIfOChSinkCurrentEntry }
::= { optIfOChSinkCurrentExtTable 1 }
OptIfOChSinkCurrentExtEntry ::=
SEQUENCE {
optIfOChSinkCurrentChromaticDispersion Integer32,
optIfOChSinkCurrentOSNR Integer32,
optIfOChSinkCurrentQ Integer32
}
optIfOChSinkCurrentChromaticDispersion OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Residual Chromatic Dispersion measured at Rx Transceiver
port."
G.Galimberti, et al. Expires January 30, 2014 [Page 36]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
::= { optIfOChSinkCurrentExtEntry 1}
optIfOChSinkCurrentOSNR OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current Optical Signal to Noise Ratio (OSNR) estimated at
Rx Transceiver port ."
::= { optIfOChSinkCurrentExtEntry 2}
optIfOChSinkCurrentQ OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"'Q' factor estimated at Rx Transceiver port."
::= { optIfOChSinkCurrentExtEntry 3}
-- Performance Monitoring
-- OTN PM Config Table
--
optIfOTNPMConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of performance monitoring configuration for the type
'optIfOTNPMConfigLayer' layer."
::= { optIfOTNPMGroup 2 }
optIfOTNPMConfigEntry OBJECT-TYPE
SYNTAX OptIfOTNPMConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the performance monitoring
configuration for the type 'optIfOTNPMConfigLayer'
layer."
INDEX { ifIndex, optIfOTNPMConfigType, optIfOTNPMConfigLayer,
optIfOTNPMConfigTCMLevel }
::= { optIfOTNPMConfigTable 1 }
OptIfOTNPMConfigEntry ::=
SEQUENCE {
G.Galimberti, et al. Expires January 30, 2014 [Page 37]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMConfigType OptIfOTNType,
optIfOTNPMConfigLayer OptIfOTNLayer,
optIfOTNPMConfigTCMLevel Unsigned32,
optIfOTNPMESRInterval Unsigned32,
optIfOTNPMSESRInterval Unsigned32,
optIfOTNPMValidIntervals Unsigned32,
optIfOTNPM15MinBip8Threshold Unsigned32,
optIfOTNPM15MinESsThreshold Unsigned32,
optIfOTNPM15MinSESsThreshold Unsigned32,
optIfOTNPM15MinUASsThreshold Unsigned32,
optIfOTNPM15MinBBEsThreshold Unsigned32,
optIfOTNPM24HourBip8Threshold Unsigned32,
optIfOTNPM24HourESsThreshold Unsigned32,
optIfOTNPM24HourSESsThreshold Unsigned32,
optIfOTNPM24HourUASsThreshold Unsigned32,
optIfOTNPM24HourBBEsThreshold Unsigned32
}
optIfOTNPMConfigType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMConfigEntry 1}
optIfOTNPMConfigLayer OBJECT-TYPE
SYNTAX OptIfOTNLayer
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for OTUk, ODUk, TCMn performance data.
1 - OTUk
2 - ODUk
3 - TCM
The ODUk/TCM sublayer PM is not related to the black link PM
management, but since this is a common PM model for the
ODU/TCM layer, we may include it here."
::= { optIfOTNPMConfigEntry 2}
optIfOTNPMConfigTCMLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..6)
MAX-ACCESS not-accessible
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 38]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"This parameter indicates the TCM level (1-6)
if the PM is of the type TCM. This will be 0 for OTUK/ODUK."
::= { optIfOTNPMConfigEntry 3}
optIfOTNPMESRInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter indicates the measurement interval
for error seconds ratio."
::= {optIfOTNPMConfigEntry 4}
optIfOTNPMSESRInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter indicates the measurement interval
for severely error seconds ratio."
::= {optIfOTNPMConfigEntry 5}
optIfOTNPMValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of contiguous 15 minute intervals for which valid
PM data is available for the particular interface."
::= { optIfOTNPMConfigEntry 6 }
optIfOTNPM15MinBip8Threshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of Bip8 encountered by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshBip8TCA. One
notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 7 }
optIfOTNPM15MinESsThreshold OBJECT-TYPE
SYNTAX Unsigned32
G.Galimberti, et al. Expires January 30, 2014 [Page 39]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of ES encountered by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshEsTCA. One
notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 8 }
optIfOTNPM15MinSESsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of SES encountered by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshSESTCA. One
notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 9 }
optIfOTNPM15MinUASsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of UAS encountered by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshUASTCA. One
notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 10 }
optIfOTNPM15MinBBEsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of UAS encountered by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshBBETCA. One
notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 11 }
optIfOTNPM24HourBip8Threshold OBJECT-TYPE
G.Galimberti, et al. Expires January 30, 2014 [Page 40]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of Bip8 encountered by the interface within any
given 24 Hour performance data collection period, which
causes the SNMP agent to send optIf15MinThreshBip8TCA. One
notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 12 }
optIfOTNPM24HourESsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of ES encountered by the interface within any
given 24 hour performance data collection period, which
causes the SNMP agent to send optIf24HourThreshEsTCA. One
notification will be sent per 24 hour per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 13 }
optIfOTNPM24HourSESsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of SES encountered by the interface within any
given 24 hour performance data collection period, which
causes the SNMP agent to send optIf24HourThreshSESsTCA. One
notification will be sent per 24 hour per interface. A value
of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 14 }
optIfOTNPM24HourUASsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of SES encountered by the interface within any
given 24 hour performance data collection period, which
causes the SNMP agent to send optIf24HourThreshUASsTCA. One
notification will be sent per 24 hour per interface. A value
of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 15 }
optIfOTNPM24HourBBEsThreshold OBJECT-TYPE
G.Galimberti, et al. Expires January 30, 2014 [Page 41]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of BBE encountered by the interface within any
given 24 hour performance data collection period, which
causes the SNMP agent to send optIf24HourThreshBBEsTCA. One
notification will be sent per 24 hour per interface. A
value of `0' will disable the notification."
::= { optIfOTNPMConfigEntry 16 }
--
-- PM Current Entry at either the OTU/ODUk/TCM
--
optIfOTNPMCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table for the Performance monitoring Current Table."
::= {optIfOTNPMGroup 3}
optIfOTNPMCurrentEntry OBJECT-TYPE
SYNTAX OptIfOTNPMCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring Current table for the type
'optIfOTNPMCurrentLayer' layer."
INDEX { ifIndex, optIfOTNPMCurrentType ,
optIfOTNPMCurrentLayer, optIfOTNPMCurrentTCMLevel }
::= { optIfOTNPMCurrentTable 1 }
OptIfOTNPMCurrentEntry ::=
SEQUENCE {
optIfOTNPMCurrentType OptIfOTNType,
optIfOTNPMCurrentLayer OptIfOTNLayer,
optIfOTNPMCurrentTCMLevel Unsigned32,
optIfOTNPMCurrentSuspectedFlag TruthValue,
optIfOTNPMCurrentBip8 Unsigned32,
optIfOTNPMCurrentESs Unsigned32,
optIfOTNPMCurrentSESs Unsigned32,
optIfOTNPMCurrentUASs Unsigned32,
optIfOTNPMCurrentBBEs Unsigned32,
optIfOTNPMCurrentESR Unsigned32,
optIfOTNPMCurrentSESR Unsigned32,
optIfOTNPMCurrentBBER Unsigned32,
G.Galimberti, et al. Expires January 30, 2014 [Page 42]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMCurrentBIP8 Unsigned32,
optIfOTNPMCurrentElapsedTime Unsigned32
}
optIfOTNPMCurrentType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMCurrentEntry 1}
optIfOTNPMCurrentLayer OBJECT-TYPE
SYNTAX OptIfOTNLayer
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for OTUk, ODUk, TCMn performance data.
1 - OTUk (OCh which is used for the black link)
2 - ODUk
3 - TCM
The ODUk/TCM sublayer PM is not related to the black link PM
management, but since this is a common PM model for the
ODU/TCM layer, we may include it here."
::= { optIfOTNPMCurrentEntry 2}
optIfOTNPMCurrentTCMLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the TCM level (1-6)
if the PM is of the type TCM. This will be 0 for OTUK/ODUK."
::= { optIfOTNPMCurrentEntry 3}
optIfOTNPMCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMCurrentEntry 4}
G.Galimberti, et al. Expires January 30, 2014 [Page 43]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMCurrentBip8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Failures occurred in an observation period."
::= { optIfOTNPMCurrentEntry 5}
optIfOTNPMCurrentESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the number of seconds in which one or more bits are
in error or during which Loss of Signal (LOS) or Alarm
Indication Signal (AIS) is detected."
::= { optIfOTNPMCurrentEntry 6}
optIfOTNPMCurrentSESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds which have a severe error.
This is the number of seconds in which the bit-error ratio =
1x10Eminus3 or during which Loss of Signal (LOS) or Alarm
Indication Signal (AIS) is detected."
::= { optIfOTNPMCurrentEntry 7}
optIfOTNPMCurrentUASs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is the number of unavailable seconds.
A period of unavailable time begins at the onset of ten
consecutive SES events. These ten seconds are considered
to be part of unavailable time. A new period of available
time begins at the onset of ten consecutive non-SES events.
These ten seconds are considered to be part of available
time."
::= { optIfOTNPMCurrentEntry 8}
optIfOTNPMCurrentBBEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
G.Galimberti, et al. Expires January 30, 2014 [Page 44]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
"An errored block not occurring as part of an SES."
::= { optIfOTNPMCurrentEntry 9}
optIfOTNPMCurrentESR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of ES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMCurrentEntry 10}
optIfOTNPMCurrentSESR OBJECT-TYPE
SYNTAX Unsigned32
UNITS ".001"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of SES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMCurrentEntry 11}
optIfOTNPMCurrentBBER OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of BER in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMCurrentEntry 12 }
optIfOTNPMCurrentBIP8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The BIP8 count for this period."
::= { optIfOTNPMCurrentEntry 13 }
optIfOTNPMCurrentElapsedTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time elapsed for this 15 minute interval"
G.Galimberti, et al. Expires January 30, 2014 [Page 45]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
::= { optIfOTNPMCurrentEntry 14 }
--
-- OTN PM Interval Table
-- Upto 96 15-minute intervals
--
optIfOTNPMIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring Interval Table."
::= { optIfOTNPMGroup 4 }
optIfOTNPMIntervalEntry OBJECT-TYPE
SYNTAX OptIfOTNPMIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring Interval table for the type
'optIfOTNPMIntervalLayer' layer."
INDEX { ifIndex, optIfOTNPMIntervalType,
optIfOTNPMIntervalLayer, optIfOTNPMIntervalTCMLevel,
optIfOTNPMIntervalNumber }
::= { optIfOTNPMIntervalTable 1 }
OptIfOTNPMIntervalEntry ::=
SEQUENCE {
optIfOTNPMIntervalType OptIfOTNType,
optIfOTNPMIntervalLayer OptIfOTNLayer,
optIfOTNPMIntervalTCMLevel Unsigned32,
optIfOTNPMIntervalNumber Unsigned32,
optIfOTNPMIntervalSuspectedFlag TruthValue,
optIfOTNPMIntervalBip8 Unsigned32,
optIfOTNPMIntervalESs Unsigned32,
optIfOTNPMIntervalSESs Unsigned32,
optIfOTNPMIntervalUASs Unsigned32,
optIfOTNPMIntervalBBEs Unsigned32,
optIfOTNPMIntervalESR Unsigned32,
optIfOTNPMIntervalSESR Unsigned32,
optIfOTNPMIntervalBBER Unsigned32,
optIfOTNPMIntervalBIP8 Unsigned32,
optIfOTNPMIntervalTimeStamp DateAndTime
}
optIfOTNPMIntervalType OBJECT-TYPE
SYNTAX OptIfOTNType
G.Galimberti, et al. Expires January 30, 2014 [Page 46]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMIntervalEntry 1}
optIfOTNPMIntervalLayer OBJECT-TYPE
SYNTAX OptIfOTNLayer
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for OTUk, ODUk, TCMn performance data.
1 - OTUk
2 - ODUk
3 - TCM
The ODUk/TCM sublayer PM is not related to the black link PM
management, but since this is a common PM model for the
ODU/TCM layer, we may include it here."
::= { optIfOTNPMIntervalEntry 2}
optIfOTNPMIntervalTCMLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the TCM level (1-6)
if the PM is of the type TCM. This will be 0 for OTUK/ODUK."
::= { optIfOTNPMIntervalEntry 3}
optIfOTNPMIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1."
::= { optIfOTNPMIntervalEntry 4}
optIfOTNPMIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 47]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMIntervalEntry 5}
optIfOTNPMIntervalBip8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Failures occurred in an observation period."
::= { optIfOTNPMIntervalEntry 6}
optIfOTNPMIntervalESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is a one-second period in which one or more bits are in
error or during which Loss of Signal (LOS) or Alarm
Indication Signal (AIS) is detected."
::= { optIfOTNPMIntervalEntry 7}
optIfOTNPMIntervalSESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds which have a severe error.
It is a one-second period which has a bit-error ratio =
1x10Eminus3 or during which Loss of Signal (LOS) or Alarm
Indication Signal (AIS) is detected."
::= { optIfOTNPMIntervalEntry 8}
optIfOTNPMIntervalUASs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is the number of unavailable seconds in this 15 minute
interval. A period of unavailable time begins at the onset
of ten consecutive SES events. These ten seconds are
considered to be part of unavailable time. A new period of
available time begins at the onset of ten consecutive
non-SES events. These ten seconds are considered to be part
of available time."
::= { optIfOTNPMIntervalEntry 9}
G.Galimberti, et al. Expires January 30, 2014 [Page 48]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMIntervalBBEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An errored block not occurring as part of an SES."
::= { optIfOTNPMIntervalEntry 10}
optIfOTNPMIntervalESR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of ES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMIntervalEntry 11}
optIfOTNPMIntervalSESR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of SES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMIntervalEntry 12}
optIfOTNPMIntervalBBER OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of BBE in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMIntervalEntry 13}
optIfOTNPMIntervalBIP8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"BIP8 for this period."
::= { optIfOTNPMIntervalEntry 14}
optIfOTNPMIntervalTimeStamp OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
G.Galimberti, et al. Expires January 30, 2014 [Page 49]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
"Time stamp of this interval."
::= { optIfOTNPMIntervalEntry 15}
--
-- PM Current Day Entry
--
optIfOTNPMCurrentDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMCurrentDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring Current Day Table."
::= { optIfOTNPMGroup 5 }
optIfOTNPMCurrentDayEntry OBJECT-TYPE
SYNTAX OptIfOTNPMCurrentDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring Current day table for the type
'optIfOTNPMCurrentDayLayer' layer."
INDEX { ifIndex, optIfOTNPMCurrentDayType,
optIfOTNPMCurrentDayLayer,
optIfOTNPMCurrentDayTCMLevel }
::= { optIfOTNPMCurrentDayTable 1 }
OptIfOTNPMCurrentDayEntry ::=
SEQUENCE {
optIfOTNPMCurrentDayType OptIfOTNType,
optIfOTNPMCurrentDayLayer OptIfOTNLayer,
optIfOTNPMCurrentDayTCMLevel Unsigned32,
optIfOTNPMCurrentDaySuspectedFlag TruthValue,
optIfOTNPMCurrentDayBip8 Unsigned32,
optIfOTNPMCurrentDayESs Unsigned32,
optIfOTNPMCurrentDaySESs Unsigned32,
optIfOTNPMCurrentDayUASs Unsigned32,
optIfOTNPMCurrentDayBBEs Unsigned32,
optIfOTNPMCurrentDayESR Unsigned32,
optIfOTNPMCurrentDaySESR Unsigned32,
optIfOTNPMCurrentDayBBER Unsigned32,
optIfOTNPMCurrentDayBIP8 Unsigned32,
optIfOTNPMCurrentDayElapsedTime Unsigned32
}
optIfOTNPMCurrentDayType OBJECT-TYPE
SYNTAX OptIfOTNType
G.Galimberti, et al. Expires January 30, 2014 [Page 50]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMCurrentDayEntry 1}
optIfOTNPMCurrentDayLayer OBJECT-TYPE
SYNTAX OptIfOTNLayer
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for OTUk, ODUk, TCMn performance data.
1 - OTUk
2 - ODUk
3 - TCM
The ODUk/TCM sublayer PM is not related to the black link PM
management, but since this is a common PM model for the
ODU/TCM layer, we may include it here."
::= { optIfOTNPMCurrentDayEntry 2}
optIfOTNPMCurrentDayTCMLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the TCM level (1-6)
if the PM is of the type TCM. This will be 0 for OTUK/ODUK."
::= { optIfOTNPMCurrentDayEntry 3}
optIfOTNPMCurrentDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMCurrentDayEntry 4}
optIfOTNPMCurrentDayBip8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Failures occurred in an observation period."
G.Galimberti, et al. Expires January 30, 2014 [Page 51]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
::= { optIfOTNPMCurrentDayEntry 5}
optIfOTNPMCurrentDayESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds which have an error.
It is a one-second period in which one or more bits are in
error or during which Loss of Signal (LOS) or Alarm
Indication Signal (AIS) is detected."
::= { optIfOTNPMCurrentDayEntry 6}
optIfOTNPMCurrentDaySESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds which have a severe error.
It is a one-second period which has a bit-error ratio =
1x10Eminus3 or during which Loss of Signal (LOS) or Alarm
Indication Signal (AIS) is detected."
::= { optIfOTNPMCurrentDayEntry 7}
optIfOTNPMCurrentDayUASs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is the number of unavailable seconds in the cunrrent day.
A period of unavailable time begins at the onset of ten
consecutive SES events. These ten seconds are considered to
be part of unavailable time. A new period of available time
begins at the onset of ten consecutive non-SES events. These
ten seconds are considered to be part of available time."
::= { optIfOTNPMCurrentDayEntry 8}
optIfOTNPMCurrentDayBBEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An errored block not occurring as part of an SES."
::= { optIfOTNPMCurrentDayEntry 9}
optIfOTNPMCurrentDayESR OBJECT-TYPE
G.Galimberti, et al. Expires January 30, 2014 [Page 52]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SYNTAX Unsigned32
UNITS ".001"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of ES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMCurrentDayEntry 10}
optIfOTNPMCurrentDaySESR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of SES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMCurrentDayEntry 11}
optIfOTNPMCurrentDayBBER OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of BBE in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMCurrentDayEntry 12}
optIfOTNPMCurrentDayBIP8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"BIP8 for this period."
::= { optIfOTNPMCurrentDayEntry 13}
optIfOTNPMCurrentDayElapsedTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time elapsed for current day"
::= { optIfOTNPMCurrentDayEntry 14 }
--
-- PM Prev Day Entry
--
optIfOTNPMPrevDayTable OBJECT-TYPE
G.Galimberti, et al. Expires January 30, 2014 [Page 53]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SYNTAX SEQUENCE OF OptIfOTNPMPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring Previous Day Table."
::= { optIfOTNPMGroup 6 }
optIfOTNPMPrevDayEntry OBJECT-TYPE
SYNTAX OptIfOTNPMPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring previous day table for the type
'optIfOTNPMPrevDayLayer' layer."
INDEX { ifIndex, optIfOTNPMPrevDayType ,
optIfOTNPMPrevDayLayer, optIfOTNPMPrevDayTCMLevel }
::= { optIfOTNPMPrevDayTable 1 }
OptIfOTNPMPrevDayEntry ::=
SEQUENCE {
optIfOTNPMPrevDayType OptIfOTNType,
optIfOTNPMPrevDayLayer OptIfOTNLayer,
optIfOTNPMPrevDayTCMLevel Unsigned32,
optIfOTNPMPrevDaySuspectedFlag TruthValue,
optIfOTNPMPrevDayBip8 Unsigned32,
optIfOTNPMPrevDayESs Unsigned32,
optIfOTNPMPrevDaySESs Unsigned32,
optIfOTNPMPrevDayUASs Unsigned32,
optIfOTNPMPrevDayBBEs Unsigned32,
optIfOTNPMPrevDayESR Unsigned32,
optIfOTNPMPrevDaySESR Unsigned32,
optIfOTNPMPrevDayBBER Unsigned32,
optIfOTNPMPrevDayBIP8 Unsigned32,
optIfOTNPMPrevDayTimeStamp DateAndTime
}
optIfOTNPMPrevDayType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMPrevDayEntry 1}
G.Galimberti, et al. Expires January 30, 2014 [Page 54]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMPrevDayLayer OBJECT-TYPE
SYNTAX OptIfOTNLayer
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for OTUk, ODUk, TCMn performance data.
1 - OTUk
2 - ODUk
3 - TCM
The ODUk/TCM sublayer PM is not related to the black link PM
ODU/TCM management, but since this is a common PM model for
the layer, we may include it here."
::= { optIfOTNPMPrevDayEntry 2}
optIfOTNPMPrevDayTCMLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the TCM level (1-6)
if the PM is of the type TCM."
::= { optIfOTNPMPrevDayEntry 3}
optIfOTNPMPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMPrevDayEntry 4}
optIfOTNPMPrevDayBip8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of pre FEC failures occurred in an observation
period."
::= { optIfOTNPMPrevDayEntry 5}
optIfOTNPMPrevDayESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds which have an error.
G.Galimberti, et al. Expires January 30, 2014 [Page 55]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
It is a one-second period in which one or more bits are in
error or during which Loss of Signal (LOS) or Alarm
Indication Signal(AIS) is detected."
::= { optIfOTNPMPrevDayEntry 6}
optIfOTNPMPrevDaySESs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds which have a severe error.
A severely errored second, is a one-second period which has
a bit-error ratio = 1x10Eminus3 or during which Loss of
Signal (LOS) or Alarm Indication Signal (AIS) is detected."
::= { optIfOTNPMPrevDayEntry 7}
optIfOTNPMPrevDayUASs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"It is the number of unavailable seconds in the previous day.
A period of unavailable time begins at the onset of ten
consecutive SES events. These ten seconds are considered to
be part of unavailable time. A new period of available time
begins at the onset of ten consecutive non-SES events.
These ten seconds are considered to be part of available
time."
::= { optIfOTNPMPrevDayEntry 8}
optIfOTNPMPrevDayBBEs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An errored block not occurring as part of an SES."
::= { optIfOTNPMPrevDayEntry 9}
optIfOTNPMPrevDayESR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of ES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMPrevDayEntry 10}
optIfOTNPMPrevDaySESR OBJECT-TYPE
G.Galimberti, et al. Expires January 30, 2014 [Page 56]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of SES in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMPrevDayEntry 11}
optIfOTNPMPrevDayBBER OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ratio of BBE in available time to total seconds in
available time during a fixed measurement interval."
::= { optIfOTNPMPrevDayEntry 12}
optIfOTNPMPrevDayBIP8 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"BIP8 for this period."
::= { optIfOTNPMPrevDayEntry 13}
optIfOTNPMPrevDayTimeStamp OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time stamp of this interval."
::= { optIfOTNPMPrevDayEntry 14}
--
-- OTN FEC PM Config Table
--
optIfOTNPMFECConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMFECConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of performance monitoring FEC configuration."
::= { optIfOTNPMGroup 7 }
optIfOTNPMFECConfigEntry OBJECT-TYPE
SYNTAX OptIfOTNPMFECConfigEntry
MAX-ACCESS not-accessible
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 57]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"A conceptual entry in the performance monitoring FEC
configuration layer."
INDEX { ifIndex, optIfOTNPMFECConfigType }
::= { optIfOTNPMFECConfigTable 1 }
OptIfOTNPMFECConfigEntry ::=
SEQUENCE {
optIfOTNPMFECConfigType OptIfOTNType,
optIfOTNPMFECValidIntervals Unsigned32,
optIfOTNPM15MinFECUnCorrectedWordsThreshold Unsigned32,
optIfOTNPM15MinPreFECBERMantissaThreshold Unsigned32,
optIfOTNPM15MinPreFECBERExponentThreshold Unsigned32
}
optIfOTNPMFECConfigType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMFECConfigEntry 1}
optIfOTNPMFECValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of contiguous 15 minute intervals for which valid
FEC PM data is available for the particular interface."
::= {optIfOTNPMFECConfigEntry 2}
optIfOTNPM15MinFECUnCorrectedWordsThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Uncorrected words encountered by the interface
within any given 15 minutes performance data collection
period, which causes the SNMP agent to send
optIf15MinThreshFECUnCorrectedWordsTCA. One notification
will be sent per interval per interface. A value of `0'
will disable the notification."
::= {optIfOTNPMFECConfigEntry 3}
G.Galimberti, et al. Expires January 30, 2014 [Page 58]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPM15MinPreFECBERMantissaThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"BER (mantissa) by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshPreFECBERTCA.
One notification will be sent per interval per interface.
A value of `0' will disable the notification."
::= {optIfOTNPMFECConfigEntry 4}
optIfOTNPM15MinPreFECBERExponentThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Pre FEC BER (exponent) by the interface within any
given 15 minutes performance data collection period, which
causes the SNMP agent to send optIf15MinThreshPreFECBERTCA.
One notification will be sent per interval per interface. A
value of `0' will disable the notification."
::= {optIfOTNPMFECConfigEntry 5}
--
-- FEC PM Table
--
optIfOTNPMFECCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMFECCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring FEC Current Table."
::= { optIfOTNPMGroup 8 }
optIfOTNPMFECCurrentEntry OBJECT-TYPE
SYNTAX OptIfOTNPMFECCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring FEC current table."
INDEX { ifIndex, optIfOTNPMFECCurrentType}
::= { optIfOTNPMFECCurrentTable 1 }
OptIfOTNPMFECCurrentEntry ::=
SEQUENCE {
G.Galimberti, et al. Expires January 30, 2014 [Page 59]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMFECCurrentType OptIfOTNType,
optIfOTNPMFECCurrentSuspectedFlag TruthValue,
optIfOTNPMCurrentFECCorrectedErr Counter64,
optIfOTNPMCurrentFECUncorrectedWords Counter64,
optIfOTNPMCurrentFECBERMantissa Unsigned32,
optIfOTNPMCurrentFECBERExponent Unsigned32,
optIfOTNPMCurrentFECMinBERMantissa Unsigned32,
optIfOTNPMCurrentFECMinBERExponent Unsigned32,
optIfOTNPMCurrentFECMaxBERMantissa Unsigned32,
optIfOTNPMCurrentFECMaxBERExponent Unsigned32,
optIfOTNPMCurrentFECAvgBERMantissa Unsigned32,
optIfOTNPMCurrentFECAvgBERExponent Unsigned32,
optIfOTNPMCurrentFECElapsedTime Unsigned32
}
optIfOTNPMFECCurrentType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMFECCurrentEntry 1}
optIfOTNPMFECCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMFECCurrentEntry 2}
optIfOTNPMCurrentFECCorrectedErr OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits corrected by the FEC are counted in the
interval."
::= { optIfOTNPMFECCurrentEntry 3}
optIfOTNPMCurrentFECUncorrectedWords OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 60]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"The number of un-corrected words by the FEC are counted over
the interval."
::= { optIfOTNPMFECCurrentEntry 4}
optIfOTNPMCurrentFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Errored bits at receiving side before the FEC
function counted over one second .. mantissa."
::= { optIfOTNPMFECCurrentEntry 5}
optIfOTNPMCurrentFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Errored bits at receiving side before the FEC
function counted over one second .. exponent."
::= { optIfOTNPMFECCurrentEntry 6}
optIfOTNPMCurrentFECMinBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum number of Errored bits at receiving side before
the FEC function counted over one second .. mantissa."
::= { optIfOTNPMFECCurrentEntry 7}
optIfOTNPMCurrentFECMinBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum number of Errored bits at receiving side before
the FEC function counted over one second.. exponent."
::= { optIfOTNPMFECCurrentEntry 8}
optIfOTNPMCurrentFECMaxBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of Errored bits at receiving side before
the FECfunction counted over one second .. mantissa."
G.Galimberti, et al. Expires January 30, 2014 [Page 61]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
::= { optIfOTNPMFECCurrentEntry 9}
optIfOTNPMCurrentFECMaxBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of Errored bits at receiving side before
the FEC function counted over one second .. exponent."
::= { optIfOTNPMFECCurrentEntry 10}
optIfOTNPMCurrentFECAvgBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Errored bits at receiving side before
the FEC function counted over one second .. mantissa."
::= { optIfOTNPMFECCurrentEntry 11}
optIfOTNPMCurrentFECAvgBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Errored bits at receiving side before
the FEC function counted over one second .. exponent."
::= { optIfOTNPMFECCurrentEntry 12}
optIfOTNPMCurrentFECElapsedTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time elapsed for this 15 minute interval."
::= { optIfOTNPMFECCurrentEntry 13 }
--
-- FEC PM Interval Table
--
optIfOTNPMFECIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMFECIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring FEC Interval Table."
::= { optIfOTNPMGroup 9 }
G.Galimberti, et al. Expires January 30, 2014 [Page 62]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMFECIntervalEntry OBJECT-TYPE
SYNTAX OptIfOTNPMFECIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring FEC interval table."
INDEX { ifIndex, optIfOTNPMFECIntervalType,
optIfOTNPMFECIntervalNumber }
::= { optIfOTNPMFECIntervalTable 1 }
OptIfOTNPMFECIntervalEntry ::=
SEQUENCE {
optIfOTNPMFECIntervalType OptIfOTNType,
optIfOTNPMFECIntervalNumber Unsigned32,
optIfOTNPMFECIntervalSuspectedFlag TruthValue,
optIfOTNPMIntervalFECCorrectedErr Counter64,
optIfOTNPMIntervalFECUncorrectedWords Counter64,
optIfOTNPMIntervalMinFECBERMantissa Unsigned32,
optIfOTNPMIntervalMinFECBERExponent Unsigned32,
optIfOTNPMIntervalMaxFECBERMantissa Unsigned32,
optIfOTNPMIntervalMaxFECBERExponent Unsigned32,
optIfOTNPMIntervalAvgFECBERMantissa Unsigned32,
optIfOTNPMIntervalAvgFECBERExponent Unsigned32,
optIfOTNPMFECIntervalTimeStamp DateAndTime
}
optIfOTNPMFECIntervalType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMFECIntervalEntry 1}
optIfOTNPMFECIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1."
::= { optIfOTNPMFECIntervalEntry 2}
G.Galimberti, et al. Expires January 30, 2014 [Page 63]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMFECIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMFECIntervalEntry 3}
optIfOTNPMIntervalFECCorrectedErr OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits corrected by the FEC are counted in the
interval."
::= { optIfOTNPMFECIntervalEntry 4}
optIfOTNPMIntervalFECUncorrectedWords OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of words un-corrected words by the FEC are
counted over the interval."
::= { optIfOTNPMFECIntervalEntry 5}
optIfOTNPMIntervalMinFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimun bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
minimum Pre FEC BER in the current 24hour period."
::= { optIfOTNPMFECIntervalEntry 6}
optIfOTNPMIntervalMinFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimun bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
minimum Pre FEC BER in the current 24hour period."
::= { optIfOTNPMFECIntervalEntry 7}
optIfOTNPMIntervalMaxFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
G.Galimberti, et al. Expires January 30, 2014 [Page 64]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
maximum Pre FEC BER in the current 24hour period."
::= { optIfOTNPMFECIntervalEntry 8}
optIfOTNPMIntervalMaxFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
maximum Pre FEC BER in the current 24hour period."
::= { optIfOTNPMFECIntervalEntry 9}
optIfOTNPMIntervalAvgFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
average Pre FEC BER in the current 24hour period."
::= { optIfOTNPMFECIntervalEntry 10}
optIfOTNPMIntervalAvgFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
average Pre FEC BER in the current 24hour period."
::= { optIfOTNPMFECIntervalEntry 11}
optIfOTNPMFECIntervalTimeStamp OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time stamp of this interval."
::= { optIfOTNPMFECIntervalEntry 12 }
--
-- FEC PM Current Day day Table
G.Galimberti, et al. Expires January 30, 2014 [Page 65]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
--
optIfOTNPMFECCurrentDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMFECCurrentDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring FEC current day table."
::= { optIfOTNPMGroup 10 }
optIfOTNPMFECCurrentDayEntry OBJECT-TYPE
SYNTAX OptIfOTNPMFECCurrentDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring FEC current day table."
INDEX { ifIndex, optIfOTNPMFECCurrentDayType }
::= { optIfOTNPMFECCurrentDayTable 1 }
OptIfOTNPMFECCurrentDayEntry ::=
SEQUENCE {
optIfOTNPMFECCurrentDayType OptIfOTNType,
optIfOTNPMFECCurrentDaySuspectedFlag TruthValue,
optIfOTNPMCurrentDayFECCorrectedErr Counter64,
optIfOTNPMCurrentDayFECUncorrectedWords Counter64,
optIfOTNPMCurrentDayMinFECBERMantissa Unsigned32,
optIfOTNPMCurrentDayMinFECBERExponent Unsigned32,
optIfOTNPMCurrentDayMaxFECBERMantissa Unsigned32,
optIfOTNPMCurrentDayMaxFECBERExponent Unsigned32,
optIfOTNPMCurrentDayAvgFECBERMantissa Unsigned32,
optIfOTNPMCurrentDayAvgFECBERExponent Unsigned32,
optIfOTNPMFECCurrentDayElapsedTime Unsigned32
}
optIfOTNPMFECCurrentDayType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMFECCurrentDayEntry 1}
optIfOTNPMFECCurrentDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
G.Galimberti, et al. Expires January 30, 2014 [Page 66]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMFECCurrentDayEntry 2}
optIfOTNPMCurrentDayFECCorrectedErr OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits corrected by the FEC are counted in the
interval."
::= { optIfOTNPMFECCurrentDayEntry 3}
optIfOTNPMCurrentDayFECUncorrectedWords OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of words un-corrected by the FEC are counted over
the Day."
::= { optIfOTNPMFECCurrentDayEntry 4}
optIfOTNPMCurrentDayMinFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimun bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
minimum PreFEC BER in the current 24hour period."
::= { optIfOTNPMFECCurrentDayEntry 5}
optIfOTNPMCurrentDayMinFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimun bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
minimum PreFEC BER in the current 24hour period."
::= { optIfOTNPMFECCurrentDayEntry 6}
optIfOTNPMCurrentDayMaxFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
G.Galimberti, et al. Expires January 30, 2014 [Page 67]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
DESCRIPTION
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
maximum PreFEC BER in the current 24hour period."
::= { optIfOTNPMFECCurrentDayEntry 7}
optIfOTNPMCurrentDayMaxFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
maximum PreFEC BER in the current 24hour period."
::= { optIfOTNPMFECCurrentDayEntry 8}
optIfOTNPMCurrentDayAvgFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
average PreFEC BER in the current 24hour period."
::= { optIfOTNPMFECCurrentDayEntry 9}
optIfOTNPMCurrentDayAvgFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
average PreFEC BER in the current 24hour period."
::= { optIfOTNPMFECCurrentDayEntry 10}
optIfOTNPMFECCurrentDayElapsedTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time elapsed for current day."
::= { optIfOTNPMFECCurrentDayEntry 11}
--
-- FEC PM Prev day Table
--
G.Galimberti, et al. Expires January 30, 2014 [Page 68]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNPMFECPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNPMFECPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Performance monitoring FEC previous day table."
::= { optIfOTNPMGroup 11 }
optIfOTNPMFECPrevDayEntry OBJECT-TYPE
SYNTAX OptIfOTNPMFECPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the Near end or Far End performance
monitoring FEC previous day table."
INDEX { ifIndex, optIfOTNPMFECPrevDayType }
::= { optIfOTNPMFECPrevDayTable 1 }
OptIfOTNPMFECPrevDayEntry ::=
SEQUENCE {
optIfOTNPMFECPrevDayType OptIfOTNType,
optIfOTNPMFECPrevDaySuspectedFlag TruthValue,
optIfOTNPMPrevDayFECCorrectedErr Counter64,
optIfOTNPMPrevDayFECUncorrectedWords Counter64,
optIfOTNPMPrevDayMinFECBERMantissa Unsigned32,
optIfOTNPMPrevDayMinFECBERExponent Unsigned32,
optIfOTNPMPrevDayMaxFECBERMantissa Unsigned32,
optIfOTNPMPrevDayMaxFECBERExponent Unsigned32,
optIfOTNPMPrevDayAvgFECBERMantissa Unsigned32,
optIfOTNPMPrevDayAvgFECBERExponent Unsigned32,
optIfOTNPMFECPrevDayTimeStamp DateAndTime
}
optIfOTNPMFECPrevDayType OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This parameter indicates the parameters for the table are
for the Near End or Far End performance data.
1 - Near End
2 - Far End "
::= { optIfOTNPMFECPrevDayEntry 1}
optIfOTNPMFECPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
G.Galimberti, et al. Expires January 30, 2014 [Page 69]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { optIfOTNPMFECPrevDayEntry 2}
optIfOTNPMPrevDayFECCorrectedErr OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits corrected by the FEC are counted in the
previous day."
::= { optIfOTNPMFECPrevDayEntry 3}
optIfOTNPMPrevDayFECUncorrectedWords OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of un-corrected words by the FEC are counted
over the previous Day."
::= { optIfOTNPMFECPrevDayEntry 4}
optIfOTNPMPrevDayMinFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
maximum Pre FEC BER in the previous 24hour period."
::= { optIfOTNPMFECPrevDayEntry 5}
optIfOTNPMPrevDayMinFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimun bit error rate at receiving side before the FEC
function counted over one second .. exponent. This is the
maximum Pre FEC BER in the previous 24hour period."
::= { optIfOTNPMFECPrevDayEntry 6}
optIfOTNPMPrevDayMaxFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
G.Galimberti, et al. Expires January 30, 2014 [Page 70]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
maximum Pre FEC BER in the previous 24hour
period (mantissa)."
::= { optIfOTNPMFECPrevDayEntry 7}
optIfOTNPMPrevDayMaxFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximun bit error rate at receiving side before the FEC
function counted over one second .. exponent (eg -3).
This is the maximum Pre FEC BER in the previous 24hour
period."
::= { optIfOTNPMFECPrevDayEntry 8}
optIfOTNPMPrevDayAvgFECBERMantissa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average bit error rate at receiving side before the FEC
function counted over one second .. mantissa. This is the
average Pre FEC BER during the previous 24hour
period (mantissa)."
::= { optIfOTNPMFECPrevDayEntry 9}
optIfOTNPMPrevDayAvgFECBERExponent OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average bit error rate at receiving side before the FEC
function counted over one second .. exponent (eg -3).
This is the average Pre FEC BER during the previous 24hour
period."
::= { optIfOTNPMFECPrevDayEntry 10}
optIfOTNPMFECPrevDayTimeStamp OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time stamp for the Prev day."
::= { optIfOTNPMFECPrevDayEntry 11}
--
G.Galimberti, et al. Expires January 30, 2014 [Page 71]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
-- OTN OTUk Alarm Table
--
optIfOTNOChOTUkAlarmTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNOChOTUkAlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh/OTUk alarm entries."
::= { optIfOTNAlarm 1 }
optIfOTNOChOTUkAlarmEntry OBJECT-TYPE
SYNTAX OptIfOTNOChOTUkAlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual entry in the OCh/OTUk alarm table."
INDEX { ifIndex }
::= { optIfOTNOChOTUkAlarmTable 1 }
OptIfOTNOChOTUkAlarmEntry ::= SEQUENCE {
optIfOTNOChOTUkAlarmLocation OptIfOTNType,
optIfOTNOChOTUkAlarmDirection OptIfDirectionality,
optIfOTNOChOTUkAlarmLayer OptIfOTNLayer,
optIfOTNOChOTUkAlarmType OptIfOTNOChAlarms,
optIfOTNOChOTUkAlarmSeverity OptIfOTNAlarmSeverity,
optIfOTNOChOTUkAlarmDate DateAndTime
}
optIfOTNOChOTUkAlarmLocation OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The object identifies indicates if this entry was for
Near end/Far end."
::= { optIfOTNOChOTUkAlarmEntry 1 }
optIfOTNOChOTUkAlarmDirection OBJECT-TYPE
SYNTAX OptIfDirectionality
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The object identifies indicates if this entry was for
for the Tx/Rx or both."
::= { optIfOTNOChOTUkAlarmEntry 2 }
optIfOTNOChOTUkAlarmLayer OBJECT-TYPE
G.Galimberti, et al. Expires January 30, 2014 [Page 72]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
SYNTAX OptIfOTNLayer
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This specifies which sublayer this alarm is for."
::= { optIfOTNOChOTUkAlarmEntry 3 }
optIfOTNOChOTUkAlarmType OBJECT-TYPE
SYNTAX OptIfOTNOChAlarms
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This specifies the type of alarm of the sublayer
'optIfOTNAlarmLayer' ."
::= { optIfOTNOChOTUkAlarmEntry 4 }
optIfOTNOChOTUkAlarmSeverity OBJECT-TYPE
SYNTAX OptIfOTNAlarmSeverity
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The object identifies the severity of the last alarm/alert
that most recently was set or cleared."
::= { optIfOTNOChOTUkAlarmEntry 5 }
optIfOTNOChOTUkAlarmDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This specifies the date and time when this alarm occurred."
::= { optIfOTNOChOTUkAlarmEntry 6 }
--
-- OTN ODUkTcm Alarm Table
--
optIfOTNODUkTcmAlarmTable OBJECT-TYPE
SYNTAX SEQUENCE OF OptIfOTNODUkTcmAlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUk/Tcm alarm entries."
::= { optIfOTNAlarm 2 }
optIfOTNODUkTcmAlarmEntry OBJECT-TYPE
SYNTAX OptIfOTNODUkTcmAlarmEntry
MAX-ACCESS not-accessible
G.Galimberti, et al. Expires January 30, 2014 [Page 73]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
STATUS current
DESCRIPTION
"A conceptual entry in the ODUk/Tcm alarm table."
INDEX { ifIndex }
::= { optIfOTNODUkTcmAlarmTable 1 }
OptIfOTNODUkTcmAlarmEntry ::= SEQUENCE {
optIfOTNODUkTcmAlarmLocation OptIfOTNType,
optIfOTNODUkTcmAlarmDirection OptIfDirectionality,
optIfOTNODUkTcmAlarmLayer OptIfOTNLayer,
optIfOTNODUkTcmAlarmTCMLevel Unsigned32,
optIfOTNODUkTcmAlarmType OptIfOTNODUkTcmAlarms,
optIfOTNODUkTcmAlarmSeverity OptIfOTNAlarmSeverity,
optIfOTNODUkTcmAlarmDate DateAndTime
}
optIfOTNODUkTcmAlarmLocation OBJECT-TYPE
SYNTAX OptIfOTNType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The object identifies indicates if this entry was for
Near end/Far end."
::= { optIfOTNODUkTcmAlarmEntry 1 }
optIfOTNODUkTcmAlarmDirection OBJECT-TYPE
SYNTAX OptIfDirectionality
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The object identifies indicates if this entry was for
for the Tx/Rx or both."
::= { optIfOTNODUkTcmAlarmEntry 2 }
optIfOTNODUkTcmAlarmLayer OBJECT-TYPE
SYNTAX OptIfOTNLayer
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This specifies which sublayer this alarm is for ODUk/TCM."
::= { optIfOTNODUkTcmAlarmEntry 3 }
optIfOTNODUkTcmAlarmTCMLevel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"TCM level 1-6 of the alarm. It will be 0 if alarm sublayer
G.Galimberti, et al. Expires January 30, 2014 [Page 74]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
is ODUk."
::= { optIfOTNODUkTcmAlarmEntry 4 }
optIfOTNODUkTcmAlarmType OBJECT-TYPE
SYNTAX OptIfOTNODUkTcmAlarms
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This specifies the type of alarm 'optIfOTNDUkTcmAlarms'
of the sublayer ."
::= { optIfOTNODUkTcmAlarmEntry 5 }
optIfOTNODUkTcmAlarmSeverity OBJECT-TYPE
SYNTAX OptIfOTNAlarmSeverity
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The object identifies the severity of the last alarm/alert
that most recently was set or cleared."
::= { optIfOTNODUkTcmAlarmEntry 6 }
optIfOTNODUkTcmAlarmDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This specifies the date and time when this alarm occurred."
::= { optIfOTNODUkTcmAlarmEntry 7 }
--
-- OTN Notifications
--
optIfOTNOChOTUkAlarmSet NOTIFICATION-TYPE
OBJECTS { optIfOTNOChOTUkAlarmLocation,
optIfOTNOChOTUkAlarmDirection,
optIfOTNOChOTUkAlarmLayer,
optIfOTNOChOTUkAlarmType,
optIfOTNOChOTUkAlarmSeverity,
optIfOTNOChOTUkAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently set OTN alarm of OCh/OTUk Layer."
::= { optIfOTNNotifications 1 }
optIfOTNOChOTUkAlarmClear NOTIFICATION-TYPE
OBJECTS { optIfOTNOChOTUkAlarmLocation,
G.Galimberti, et al. Expires January 30, 2014 [Page 75]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
optIfOTNOChOTUkAlarmDirection,
optIfOTNOChOTUkAlarmLayer,
optIfOTNOChOTUkAlarmType,
optIfOTNOChOTUkAlarmSeverity,
optIfOTNOChOTUkAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently clear OTN alarm of OCh/OTUk
Layer. "
::= { optIfOTNNotifications 2 }
optIfOTNODUkTcmAlarmSet NOTIFICATION-TYPE
OBJECTS { optIfOTNODUkTcmAlarmLocation,
optIfOTNODUkTcmAlarmDirection,
optIfOTNODUkTcmAlarmLayer,
optIfOTNODUkTcmAlarmTCMLevel,
optIfOTNODUkTcmAlarmType,
optIfOTNODUkTcmAlarmSeverity,
optIfOTNODUkTcmAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently set OTN alarm of OTUk/Tcm
Layer. "
::= { optIfOTNNotifications 3 }
optIfOTNODUkTcmAlarmClear NOTIFICATION-TYPE
OBJECTS { optIfOTNODUkTcmAlarmLocation,
optIfOTNODUkTcmAlarmDirection,
optIfOTNODUkTcmAlarmLayer,
optIfOTNODUkTcmAlarmTCMLevel,
optIfOTNODUkTcmAlarmType,
optIfOTNODUkTcmAlarmSeverity,
optIfOTNODUkTcmAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently cleared OTN alarm of OTUk/Tcm
Layer. "
::= { optIfOTNNotifications 4 }
END
G.Galimberti, et al. Expires January 30, 2014 [Page 76]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
7. Relationship to Other MIB Modules
7.1. Relationship to the [TEMPLATE TODO] MIB
7.2. MIB modules required for IMPORTS
8. Definitions
[TEMPLATE TODO]: put your valid MIB module here.
A list of tools that can help automate the process of
checking MIB definitions can be found at
http://www.ops.ietf.org/mib-review-tools.html
9. Security Considerations
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
G.Galimberti, et al. Expires January 30, 2014 [Page 77]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
10. IANA Considerations
Option #1:
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
sampleMIB { mib-2 XXX }
Option #2:
Editor's Note (to be removed prior to publication): the IANA is
requested to assign a value for "XXX" under the 'mib-2' subtree and
to record the assignment in the SMI Numbers registry. When the
assignment has been made, the RFC Editor is asked to replace "XXX"
(here and in the MIB module) with the assigned value and to remove
this note.
Note well: prior to official assignment by the IANA, an internet
draft MUST use placeholders (such as "XXX" above) rather than actual
numbers. See RFC4181 Section 4.5 for an example of how this is done
in an internet draft MIB module.
Option #3:
This memo includes no request to IANA.
11. Contributors
Arnold Mattheus
Deutsche Telekom
Darmstadt
Germany
email a.mattheus@telekom.de
Manuel Paul
G.Galimberti, et al. Expires January 30, 2014 [Page 78]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Deutsche Telekom
Berlin
Germany
email Manuel.Paul@telekom.de
Frank Luennemann
Deutsche Telekom
Munster
Germany
email Frank.Luennemann@telekom.de
Scott Mansfield
Ericsson Inc.
email scott.mansfield@ericsson.com
Najam Saquib
Cisco
Ludwig-Erhard-Strasse 3
ESCHBORN, HESSEN 65760
GERMANY
email nasaquib@cisco.com
Walid Wakim
Cisco
9501 Technology Blvd
ROSEMONT, ILLINOIS 60018
UNITED STATES
email wwakim@cisco.com
Ori Gerstel
Cisco
32 HaMelacha St., (HaSharon Bldg)
SOUTH NETANYA, HAMERKAZ 42504
ISRAEL
email ogerstel@cisco.com
12. References
12.1. Normative References
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
G.Galimberti, et al. Expires January 30, 2014 [Page 79]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD
58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC3591] Lam, H-K., Stewart, M., and A. Huynh, "Definitions of
Managed Objects for the Optical Interface Type", RFC 3591,
September 2003.
[RFC6205] Otani, T. and D. Li, "Generalized Labels for Lambda-
Switch-Capable (LSC) Label Switching Routers", RFC 6205,
March 2011.
[ITU.G698.2]
International Telecommunications Union, "Amplified
multichannel dense wavelength division multiplexing
applications with single channel optical interfaces ",
ITU-T Recommendation G.698.2, November 2009.
[ITU.G709]
International Telecommunications Union, "Interface for the
Optical Transport Network (OTN) ", ITU-T Recommendation
G.709, March 2003.
[ITU.G872]
International Telecommunications Union, "Architecture of
optical transport networks ", ITU-T Recommendation G.872,
November 2001.
[ITU.G798]
International Telecommunications Union, "Characteristics
of optical transport network hierarchy equipment
functional blocks ", ITU-T Recommendation G.798, October
2010.
[ITU.G874]
International Telecommunications Union, "Management
aspects of optical transport network elements ", ITU-T
Recommendation G.874, July 2010.
[ITU.G874.1]
G.Galimberti, et al. Expires January 30, 2014 [Page 80]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
International Telecommunications Union, "Optical transport
network (OTN): Protocol-neutral management information
model for the network element view ", ITU-T Recommendation
G.874.1, January 2002.
[ITU.G959.1]
International Telecommunications Union, "Optical transport
network physical layer interfaces ", ITU-T Recommendation
G.959.1, November 2009.
[ITU.G826]
International Telecommunications Union, "End-to-end error
performance parameters and objectives for international,
constant bit-rate digital paths and connections ", ITU-T
Recommendation G.826, November 2009.
[ITU.G8201]
International Telecommunications Union, "Error performance
parameters and objectives for multi-operator international
paths within the Optical Transport Network (OTN) ", ITU-T
Recommendation G.8201, April 2011.
[ITU.G694.1]
International Telecommunications Union, "Spectral grids
for WDM applications: DWDM frequency grid ", ITU-T
Recommendation G.694.1, June 2002.
[ITU.G7710]
International Telecommunications Union, "Common equipment
management function requirements ", ITU-T Recommendation
G.7710, May 2008.
12.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999.
[RFC4181] Heard, C., "Guidelines for Authors and Reviewers of MIB
Documents", BCP 111, RFC 4181, September 2005.
[I-D.kunze-g-698-2-management-control-framework]
G.Galimberti, et al. Expires January 30, 2014 [Page 81]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Kunze, R., "A framework for Management and Control of
optical interfaces supporting G.698.2", draft-
kunze-g-698-2-management-control-framework-00 (work in
progress), July 2011.
[RFC4054] Strand, J. and A. Chiu, "Impairments and Other Constraints
on Optical Layer Routing", RFC 4054, May 2005.
Appendix A. Change Log
This optional section should be removed before the internet draft is
submitted to the IESG for publication as an RFC.
Note to RFC Editor: please remove this appendix before publication as
an RFC.
Appendix B. Open Issues
Note to RFC Editor: please remove this appendix before publication as
an RFC.
Authors' Addresses
Gabriele Galimberti (editor)
Cisco
Via Philips,12
20052 - Monza
Italy
Phone: +390392091462
Email: ggalimbe@cisco.com
Ruediger Kunze (editor)
Deutsche Telekom
Dddd, xx
Berlin
Germany
Phone: +49xxxxxxxxxx
Email: RKunze@telekom.de
G.Galimberti, et al. Expires January 30, 2014 [Page 82]
Internet-Draft draft-galikunze-ccamp-opt-imp-snmp-mib-01 July 2013
Hing-Kam Lam (editor)
Alcatel-Lucent
600-700 Mountain Avenue, Murray Hill
New Jersey, 07974
USA
Phone: +17323313476
Email: kam.lam@alcatel-lucent.com
Dharini Hiremagalur (editor)
Juniper
1194 N Mathilda Avenue
Sunnyvale - 94089 California
USA
Phone: +1408
Email: dharinih@juniper.net
G.Galimberti, et al. Expires January 30, 2014 [Page 83]