Routing Area Working Group H. Gredler
Internet-Draft Juniper Networks, Inc.
Intended status: Standards Track February 20, 2013
Expires: August 24, 2013
Advertising MPLS labels in IGPs
draft-gredler-rtgwg-igp-label-advertisement-02
Abstract
Historically MPLS label distribution was driven by session oriented
protocols. In order to obtain a particular routers label binding for
a given destination FEC one needs to have first an established
session with that node.
This document describes a mechanism to distribute FEC/label mappings
trough flooding protocols. Flooding protocols publish their objects
for an unknown set of receivers, therefore one can efficiently scale
label distribution for use cases where the receiver of label
information is not directly connected.
Application of this technique are found in the field of backup (LFA)
computation, Label switched path stitching, traffic engineering and
egress ASBR link selection.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 24, 2013.
Gredler Expires August 24, 2013 [Page 1]
Internet-Draft Advertising MPLS labels in IGPs February 2013
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Motivation and Applicability . . . . . . . . . . . . . . . . . 3
2.1. Explicit One hop tunnels . . . . . . . . . . . . . . . . . 4
2.2. Egress ASBR Link Selection . . . . . . . . . . . . . . . . 5
2.3. Explicit Path Routing through Label Stacking . . . . . . . 6
2.4. Stitching MPLS Label Switched Path Segments . . . . . . . . 7
3. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 8
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 8
5. Security Considerations . . . . . . . . . . . . . . . . . . . . 8
6. References . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.1. Normative References . . . . . . . . . . . . . . . . . . . 9
6.2. Informative References . . . . . . . . . . . . . . . . . . 9
6.3. References . . . . . . . . . . . . . . . . . . . . . . . . 9
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gredler Expires August 24, 2013 [Page 2]
Internet-Draft Advertising MPLS labels in IGPs February 2013
1. Introduction
MPLS label allocations are predominantly distributed by using the LDP
[RFC5036], RSVP [RFC5151] or labeled BGP [RFC3107] protocol. All of
those protocols have in common that they are session oriented, which
means that in order to learn the Label Information database of a
particular router one needs to have a direct control-plane session
using the given protocol.
There are a couple of interesting use cases where the consumer of a
MPLS label allocation may not be adjacent to the router having
allocated the label. Bringing up an explicit session using existing
label distribution protocols between the non-adjacent label allocator
and the label consumer is the existing remedy for this dilemma.
For LDP protection routing LDP next next hop labels [NNHOP] have been
proposed to provide the 2 hop neighborhood labels. While the 2 hop
neighborhood provides good backup coverage for the typical network
operator topology it is inadequate for some sparse for example ring
like topologies.
Depending on the application, retrieval and setup of forwarding state
of such >1 hop label allocations may only be transient. As such
configuring and un-configuring the explicit session is an operational
burden and therefore should be avoided.
2. Motivation and Applicability
It may not be immediate obvious, however introduction of Remote LFA
[I-D.ietf-rtgwg-remote-lfa] technology has implied important changes
for an IGP implementation. Previously the IGP had a one-way
communication path with the LDP module. The IGP supplies tracking
routes and LDP selects the best neighbor based upon FEC to tracking
routes exact matching results. Remote LFA changes that relationship
such that there is a bi-directional communication path between the
IGP and LDP. Now the IGP needs to learn about if a label switched
path to a given destination prefix has been established and what the
ingress label for getting there is. The IGP needs to push that label
for the tracking routes of destinations beyond a remote LFA neighbor.
Since the IGP now creates forwarding state based on label information
it may make sense to distribute label by the IGP as well. This
section lists example applications of IGP distribution of MPLS
labels.
Gredler Expires August 24, 2013 [Page 3]
Internet-Draft Advertising MPLS labels in IGPs February 2013
2.1. Explicit One hop tunnels
Deployment of Loop free alternate backup technology RFC 5286
[RFC5286] results in backup graphs whose coverage is highly dependent
on the underlying Layer-3 topology. Typical network deployments
provide backup coverage less than 100 percent (see RFC 6571 Section
4.3 for Results [RFC6571]) for IGP destination prefixes.
By closer examining the coverage gaps from the referenced production
network topologies, it becomes obvious that most topologies lacking
backup coverage are close to ring shaped topologies (Figure 1).
Remote LFA [I-D.ietf-rtgwg-remote-lfa] has introduced the notion of a
"remote" LFA neighbor. This helper router which is both in P and Q
space could forward the traffic to the final destination. Router 'H'
is in P space, however due to the actual metric allocation router 'H'
is not in Q space.
+-----+
| D |
+-----+
/ \
/ M1 \ M4 >= (M1 + M2 + M3)
/ \
+-----+ +-----+
| PLR | | H |
+-----+ +-----+
\ /
\ M2 / M3
\ /
+-----+
| E |
+-----+
Figure 1: Coverage gap analysis
The protection router (PLR) evaluates for a primary path to
destination 'D' if {E -> H -> D} is a viable backup path. Because
the metric M4 {H -> D} is higher than the sum of the original primary
path and the path from router 'H' to the PLR, this particular path
would result in a loop and therefore is rejected.
Now consider that router 'H' would advertise a label for FEC 'D',
which has the semantics that H will POP the label and forward to the
destination node 'D'. This is done irrespective of the underlying
IGP metric 'M4' it is a 'strict forwarding' label. The PLR router
can now construct a label stack where the outermost label provides
transport to router 'H'. The next label on the MPLS stack is the IGP
Gredler Expires August 24, 2013 [Page 4]
Internet-Draft Advertising MPLS labels in IGPs February 2013
learned 'strict forwarding label' label. Note that the label 'strict
forwarding' semantics are similar to a 1-hop ERO (Explicit route
object). The Remote 'LFA' calculation would ned to get changed, such
that even if a node is not in PQ space, but rather in P space, it may
get used as a backup neighbor if it advertises a strict forwarding
label to the final destination. A recursive version of the algorithm
is applicable as well as long a node in P space has some non looping
LSP path to the final destination. The PLR router can now program a
backup path irrespective of the undesirable underlying layer-3
topology.
Using exisiting tunnels for backup routing has been previously
described in [I-D.bryant-ipfrr-tunnels]. Section 5.2.3 'Directed
forwarding' describes an option to insert a single MPLS label between
the tunnel and the payload. Traffic may thereby be directed to a
particular neighbor. The mechanism described in this document, is an
MPLS specific manifestation of 'Directed forwarding'.
2.2. Egress ASBR Link Selection
In the topology described in Figure 2. router 'S' is facing a
dilemma. Router S receives a BGP route from all of its 4 upstream
routers. Using existing mechanism the provider owning AS1 can
control the loading of its direct links *to* its ASBR1 and ASBR2,
however it cannot control the load of the links beyond the ASBRs,
except manually tweaking the eBGP import policy and filtering out a
certain prefix. It would be be more desirable to have visibility of
all four BGP paths and be able to control the loading of those four
paths using Weighted ECMP. Note that the computation of the 'Weight'
percentage and the component doing this computation (Router embedded
or SDN) is outside the scope of this document.
If all the ASes would be under one common administrative control then
the network operator could deploy a forwarding hierarchy by using
[RFC3107] to learn about the remote-AS BGP nexthop addresses and
associated labels. An ingress router 'S' would then stack the
transport label to its local egress ASBR and the remote ASBR supplied
label. In reality it is hard to convince a peering AS to deploy
another protocol just in order to easier control the egress load on
the WAN links for the ingress AS.
A 'strict forwarding' paradigm would solve this problem: An Egress
ASBR (e.g. ASBR 1 and 2) allocates a strict forwarding label toward
all of its peering ASes and advertises it into its local IGP. The
forwarding state of all those labels is to POP off the label and
forward to the respective interface. The ingress router 'S' then
builds a MPLS label stack by combining its local transport label to
ASBR3 or ASBR4 with the IGP learned label pointing to the remote-AS
Gredler Expires August 24, 2013 [Page 5]
Internet-Draft Advertising MPLS labels in IGPs February 2013
ASBR.
-------------traffic-flow--------->
<-----------signaling-flow---------
:
: AS3
: +-------+
AS1 _:___+ ASBR3 |
/ : +-------+
+-------+ :
| ASBR1 | : AS4
+-------+ : +-------+
/ \_:___+ ASBR4 |
/ : +-------+
/ :
+-----+ :
| S | :
+-----+ : AS5
\ : +-------+
\ _:___+ ASBR5 |
\ / : +-------+
+-------+ :
| ASBR2 | : AS6
+-------+ : +-------+
\_:___+ ASBR6 |
: +-------+
:
Figure 2: Egress ASBR Link selection
2.3. Explicit Path Routing through Label Stacking
IGP advertised strict forwarding labels can be utilized for
constructing simple EROs via virtue of the MPLS label stack. In a
classical traffic engineering problem (Figure 3) is illustrated. The
best IGP path between {S,D} is {S, R3, R4, D}. Unfortunately this
path is congested. It turns out that the links {S, R1}, {R1, R4} and
{R2, R4} do have some spare capacity. In the past a C-SPF
calculation would have passed the ERO {S, R1, R4, R2, D} down to RSVP
for signaling. The conceptional problem with RSVP signaled paths is
that they cannot by shared with other nodes in the network. Hence
all potential ingress routers need to setup their "private" ERO path
and allocate network signaling resources and forwarding state.
Gredler Expires August 24, 2013 [Page 6]
Internet-Draft Advertising MPLS labels in IGPs February 2013
+----+ +----+
| R1 +---------+ R2 |
+----+ 2 +----+
/ \ | \
/ 2 \ | \ 2
/ \ | \
+-----+ \ | +-----+
| S | \ 5 | 5 | D |
+-----+ \ | +-----+
\ \ | /
\ 1 \ | / 1
\ \ | /
+----+ +----+
| R3 +---------+ R4 |
+----+ 1 +----+
Figure 3: Explicit Routing using Label stacking
Consider now every router along the path does advertise a strict
forwarding label for its direct neighbor. Router S could now
construct a couple of paths for avoiding the hot links without
explicitly signaling them.
o {S, R1, R2, D}
o {S, R1, R4, D}
o {S, R1, R4, R2, D}
Note that not every hop in the ERO needs to be unique label in the
label stack. This is undesired as existing forwarding hardware
technology has got upper limits how much labels can get pushed on the
label stack. In fact an existing tunnel (for example LDP tunnel {S,
R1, R2} can be reused for certain path segments.
2.4. Stitching MPLS Label Switched Path Segments
One of the shortcomings of existing traffic-engineering solutions is
that existing label switched paths cannot get advertised and shared
by many ingress routers in the network. In the example network
(Figure 4) a LSP with an ERO of {R4, R2, R6} has been established in
order to utilize two unused north / south links. The only way to
attract traffic to that LSP is to advertise the LSP as a forwarding
adjacency. This causes loss of the original path information which
might be interesting for a potential router which might wants to use
this LSP for backup purposes. A computing router would need to have
all underlying fate-sharing and bandwidth utilization information.
Gredler Expires August 24, 2013 [Page 7]
Internet-Draft Advertising MPLS labels in IGPs February 2013
+----+ +----+ +----+
| R1 +---------+ R2 +---------+ R5 |
+----+ 2 +----+ 2 +----+
/ \ | \ \
/ 2 \ | \ \ 2
/ \ | \ \
+----+ \ | \ +----+
| S | \ 5 | 5 \ 5 | D |
-----+ \ | \ +----+
\ \ | \ /
\ 1 \ | \ / 1
\ \ | \ /
+----+ +----+ +----+
| R3 +---------+ R4 |---------+ R6 |
+----+ 1 +----+ 1 +----+
Figure 4: Advertising path segments
The IGP on R4 can now advertise the LSP segment by advertising its
ingress label and optionally pass the original ERO, such that any
upstream router can do their fate-sharing computations. Potential
ingress routers now can use this LSP as a segment of the overall LSP.
Furthermore ingress routers can combine label advertisements from
different routers along the path. For example router S could stacks
its LDP path to R2 {S, R1, R2} plus the IGP learned RSVP LSP {R4, R5,
R6} plus a strict forwarding label {R6, D}.
3. Acknowledgements
Many thanks to Yakov Rehkter, Ina Minei, Stephane Likowski and Bruno
Decraene for their useful comments.
4. IANA Considerations
This memo includes no request to IANA.
5. Security Considerations
This document does not introduce any change in terms of IGP security.
It simply proposes to flood existing information gathered from other
protocols via the IGP.
6. References
Gredler Expires August 24, 2013 [Page 8]
Internet-Draft Advertising MPLS labels in IGPs February 2013
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3107] Rekhter, Y. and E. Rosen, "Carrying Label Information in
BGP-4", RFC 3107, May 2001.
[RFC5036] Andersson, L., Minei, I., and B. Thomas, "LDP
Specification", RFC 5036, October 2007.
[RFC5151] Farrel, A., Ayyangar, A., and JP. Vasseur, "Inter-Domain
MPLS and GMPLS Traffic Engineering -- Resource Reservation
Protocol-Traffic Engineering (RSVP-TE) Extensions",
RFC 5151, February 2008.
[RFC5286] Atlas, A. and A. Zinin, "Basic Specification for IP Fast
Reroute: Loop-Free Alternates", RFC 5286, September 2008.
[RFC6571] Filsfils, C., Francois, P., Shand, M., Decraene, B.,
Uttaro, J., Leymann, N., and M. Horneffer, "Loop-Free
Alternate (LFA) Applicability in Service Provider (SP)
Networks", RFC 6571, June 2012.
6.2. Informative References
[I-D.bryant-ipfrr-tunnels]
Bryant, S., Filsfils, C., Previdi, S., and M. Shand, "IP
Fast Reroute using tunnels", draft-bryant-ipfrr-tunnels-03
(work in progress), November 2007.
[I-D.ietf-rtgwg-remote-lfa]
Bryant, S., Filsfils, C., Previdi, S., Shand, M., and S.
Ning, "Remote LFA FRR", draft-ietf-rtgwg-remote-lfa-01
(work in progress), December 2012.
6.3. References
[NNHOP] Chen, E., Shen, N., and A. Tian, "Discovering LDP Next-
Nexthop Labels", November 2005, <http://tools.ietf.org/
html/draft-shen-mpls-ldp-nnhop-label-02>.
Gredler Expires August 24, 2013 [Page 9]
Internet-Draft Advertising MPLS labels in IGPs February 2013
Author's Address
Hannes Gredler
Juniper Networks, Inc.
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: hannes@juniper.net
Gredler Expires August 24, 2013 [Page 10]