L H. Jie
Internet-Draft ZTE Corporation
Intended status: Standards Track November 15, 2020
Expires: May 15, 2021
An Enhanced Source Routing Header Based on RH3
draft-han-6man-enhanced-source-routing-header-01
Abstract
IPv6 Routing header type 3 (termed as RH3) is defined and used in
Low-Power and Lossy Networks (LLNs) that are typically constrained in
resources (limited communication data rate, processing power, energy
capacity, memory). Based on the mechanisms introduced by RH3, this
document specifies an new IPv6 Routing Header type that provides
encapsulation capability of segments with various lengths and can be
applied to more scenarios.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 16, 2021.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
Jie Expires May 16, 2021 [Page 1]
Internet-Draft Enhanced Source Routing Header November 2020
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 3
3. Format of the Source Routing Header . . . . . . . . . . . . . 3
4. Format of the Enhanced Source Routing Header . . . . . . . . 3
5. Generating E-SRH . . . . . . . . . . . . . . . . . . . . . . 7
6. Processing E-SRH . . . . . . . . . . . . . . . . . . . . . . 7
7. Deployment Considerations . . . . . . . . . . . . . . . . . . 8
7.1. Heterogeneous Segment List . . . . . . . . . . . . . . . 9
7.2. Independent Arguments in E-SRH . . . . . . . . . . . . . 9
7.3. ICMP Error Processing . . . . . . . . . . . . . . . . . . 9
7.4. Repair Path . . . . . . . . . . . . . . . . . . . . . . . 10
7.5. Binding to Outer Segment List . . . . . . . . . . . . . . 10
7.6. In-situ OAM . . . . . . . . . . . . . . . . . . . . . . . 10
7.7. NAT Service Funtion . . . . . . . . . . . . . . . . . . . 11
7.8. Operation and Maintenance . . . . . . . . . . . . . . . . 11
7.9. Upper-Layer Checksums . . . . . . . . . . . . . . . . . . 11
8. Security Considerations . . . . . . . . . . . . . . . . . . . 12
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12
10. Normative References . . . . . . . . . . . . . . . . . . . . 12
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 14
1. Introduction
Routing headers are defined in [RFC8200]. [RFC6554] specifies the
Source Routing Header (SRH), i.e., IPv6 Routing header type 3 (termed
as RH3), for use strictly between RPL routers in the Low-Power and
Lossy Networks (LLNs) [RFC6550], which are typically constrained in
resources (limited communication data rate, processing power, energy
capacity, memory). It introduces mechanisms to compact the source
route entries when all entries share the same prefix with the IPv6
Destination Address of a packet carrying an RH3, a typical scenario
in LLNs using source routing. The compaction mechanism reduces
consumption of scarce resources such as channel capacity. However,
it is challenging when all entries do not have the same prefix, for
example, only a part of entries share the same prefix, but still want
to encode all routries in a single routing header and reduce the
overhead.
This document specifies an enhanced Source Routing Header (termed as
E-SRH) to enhance the encapsulation capability of segments with
various lengths and different types, and attempt to apply to more
scenarios that using source routing mechanism.
Jie Expires May 16, 2021 [Page 2]
Internet-Draft Enhanced Source Routing Header November 2020
2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Format of the Source Routing Header
The Source Routing Header defined in [RFC6554] has the following
format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CmprI | CmprE | Pad | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .
. Addresses[1..n] .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Source Routing Header format
Where CmprI, CmprE, and Pad fields allow compaction of the
Address[1..n] vector when all entries share the same prefix as the
IPv6 Destination Address field of the packet carrying the RH3. The
CmprI and CmprE fields indicate the number of prefix octets that are
shared with the IPv6 Destination Address of the packet carrying the
RH3. The shared prefix octets are not carried within the Routing
header and each entry in Address[1..n-1] has size (16 - CmprI) octets
and Address[n] has size (16 - CmprE) octets.
4. Format of the Enhanced Source Routing Header
To provide the encapsulation capability of segments with various
lengths, this section defines the Enhanced Source Routing Header
(E-SRH). The basic idea is to place the CmprI or CmprE information
with each segment element. The E-SRH has the following format:
Jie Expires May 16, 2021 [Page 3]
Internet-Draft Enhanced Source Routing Header November 2020
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| List Len | Offset | Flags | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Cmpr | Segment 1 //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// Type | Cmpr | Segment 2 //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// ... ... //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// Type | Cmpr | Segment N //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// //
// Optional Type Length Value objects (variable) //
// //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Enhanced Source Routing Header format
where:
Next Header: Defined in [RFC8200], Section 4.4. It identifies the
type of header immediately following the Routing header.
Hdr Ext Len: Defined in [RFC8200], Section 4.4. It represents the
length of the Routing header in 8-octet units, not including the
first 8 octets.
Routing Type: TBA.
Segments Left: Defined in [RFC8200], Section 4.4. It represents the
number of route segments remaining, i.e., number of explicitly listed
intermediate nodes still to be visited before reaching the final
destination. Note that it represents the count of intermediate
nodes, instead of the count of segments always in constant 128-bit
units in the routing header. Both this document and [RFC6554] may
take segments less than 128 bits, for example, 32 bits, in the
routing header.
List Len: 8-bit unsigned integer. It represents the length of the
Segment List field in 8-octet units. Note that the size of the
entire Segment List must be aligned to 8 bytes. For this purpose, it
Jie Expires May 16, 2021 [Page 4]
Internet-Draft Enhanced Source Routing Header November 2020
may be necessary to pad meaningless zeros after the last segment
(i.e., segment N). List Len field must be less than Hdr Ext Len, or
equal to Hdr Ext Len when E-SRH does not contain optional TLVs.
Offset: 12-bit unsigned integer. It represents the index of
currently active segment in segment list, when the segment list
contained in E-SRH is regarded as an array in bytes. When an element
in a segment list array is accessed according to Offset field, its
access range must not exceed the range represented by List Len * 8.
Flags: 4 bits of flags. No flags are defined currently.
Reserved: This field is unused. It MUST be initialized to zero by
the sender and MUST be ignored by the receiver.
Each <Type, Cmpr, Segment> tuple provide the information of each
segment element in the segment list, and it has variable length.
Type: 4 bits. It represents the type of the segment. The following
types are defined:
0: Indicates that the corresponding Segment field is a complete
IPv6 address. Note that the corresponding Segment field does not
necessarily occupy 16 bytes, and its length is given by Cmpr
field. This is because the low-order position of many IPv6
addresses is 0, and it is not necessary to store the entire 16
bytes in the Segment field. The IPv6 address may be a normal
address that identify node or interface, or an SRv6 SID
([RFC8402]) that has further functions.
1: Indicates that the corresponding Segment field is 1-octet of
IPv6 address fragment. Similar with [RFC6554], the value of
Segment field can be stiched with the prefix contained in the IPv6
Destination Address to form a complete IPv6 address. The Cmpr
field indicates the number of prefix octets that are shared with
the IPv6 Destination Address. For the stiched IPv6 address, the
high-order position is the prefix, immediately following the value
of the Segment field, and the low-order position is filled with
zeros.
2: Indicates that the corresponding Segment field is 2-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
3: Indicates that the corresponding Segment field is 3-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
4: Indicates that the corresponding Segment field is 4-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
Jie Expires May 16, 2021 [Page 5]
Internet-Draft Enhanced Source Routing Header November 2020
5: Indicates that the corresponding Segment field is 5-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
6: Indicates that the corresponding Segment field is 6-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
7: Indicates that the corresponding Segment field is 7-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
8: Indicates that the corresponding Segment field is 8-octet of
IPv6 address fragment. The stiching method is the same as Type-1.
9: Indicates that the corresponding Segment field is 3-octet of
MPLS Label. The MPLS Label can be mapped to a complete IPv6
address.
10: Indicates that the corresponding Segment field is 4 bytes of
SR-MPLS SID index([RFC8402]). The index can be mapped to a
complete IPv6 address.
11: Indicates that the corresponding Segment field is 4 bytes of
BIER index([RFC8279]). The index can be mapped to a complete IPv6
address.
15: Indicates that the corresponding Segment field is an argument
that is used by the previous Segment element in E-SRH. The
segment's length is given by Cmpr field. Note that Segment with
argument types is not counted in the count represented by the
segment left field.
Cmpr: 4 bits. It represents the length of the prefix in octet units
for Type-1 to Type-8. For Type-0, it represents the actual length of
the Segment field, For Type-9, Type-10 and Type-11, it has no meaning
and can be set to 0.
Segment: Represents the nth segment in the Segment List. Similar
with [RFC6554], the Segment List is encoded in E-SRH in positive
order. The Segment field has variable length.
Padding: Optional padding field immediately following Segment N
field. It is used to pad the Segment List to a multiple of 8 octets.
If the Segment List is already 8-byte aligned, there is no need to
have a Padding field.
Optional TLVs: To be defined in future.
Jie Expires May 16, 2021 [Page 6]
Internet-Draft Enhanced Source Routing Header November 2020
5. Generating E-SRH
For a segment list <S1, S2, S3,..., Sn>, the headend can encode it in
E-SRH. S1 is placed to DA field of IPv6 header, and S1 to Sn can be
also placed in the Segment 1 to Segment N fields respectively.
Because S1 is also placed in the Segment 1 field, Offset field needs
to be set to the value that point to <Type, Cmpr, Segment 2> tuple,
i.e., Offset = sizeof <Type, Cmpr, Segment 1>. In addition, Segment
Left field is set to n-1, which means there are n-1 Segments left to
be processed in the Segment List.
For the above segment list <S1, S2, S3,..., Sn>, the headend may not
place S1 in E-SRH again, then E-SRH only needs to contain n-1
segments. In this case, S2 to Sn will be placed in the Segment 1 to
Segment N-1 fields respectively. Offset needs to be set to the value
that point to <Type, Cmpr, Segment 1>, i.e., Offset = 0. In
addition, Segment Left field is still set to n-1, which means there
are n-1 segments left to be processed in the Segment List.
6. Processing E-SRH
E-SRH is examined and processed when the IPv6 packet reaches the node
identified in the Destination Address field of the IPv6 header. In
that node, dispatching on the Next Header field of the immediately
preceding header causes the Routing header module to be invoked.
The following describes the algorithm performed when processing an
E-SRH:
If next argument item is needed in the current segment processing {
Read the next <Type, Cmpr, Segment> tuple which is pointed by
current Offset field:
Type 15(Arg), Segment's length is determined by Cmpr field;
If Type is not 15 {
Send an ICMP Parameter Problem, Code 0, message to the Source
Address, pointing to the Offset field, and discard the packet;
}
Offset += sizeof (next <Type, Cmpr, Segment>);
if Offset > List Len * 8 {
Send an ICMP Parameter Problem, Code 0, message to the Source
Address, pointing to the Offset field, and discard the packet;
}
Continues the remaining processing of the current element with
additional aruguments (note: long argument if necessary, instead
of using multiple arguments);
Jie Expires May 16, 2021 [Page 7]
Internet-Draft Enhanced Source Routing Header November 2020
}
if Segments Left = 0 {
proceed to process the next header in the packet, whose type is
identified by the Next Header field in the Routing header;
}
else {
Read the next <Type, Cmpr, Segment> tuple which is pointed by
current Offset field, in detailed:
For Type 0, Segment's length is determined by Cmpr field;
For Type 1-8, Segment's length is 1-8 bytes respectively;
For Type 9(MPLS), Segment's length is 3 bytes;
For Type 10-11(index), Segment's length is 4 bytes;
If Type is 15 or unknown {
Send an ICMP Parameter Problem, Code 0, message to the Source
Address, pointing to the Offset field, and discard the packet;
}
Offset += sizeof (next <Type, Cmpr, Segment>);
if Offset > List Len * 8 {
Send an ICMP Parameter Problem, Code 0, message to the Source
Address, pointing to the Offset field, and discard the packet;
}
decrement Segments Left by 1;
Copy the stiched/mapped IPv6 address to the destination address
of the IPv6 header;
if the IPv6 Hop Limit is less than or equal to 1 {
send an ICMP Time Exceeded -- Hop Limit Exceeded in Transit
message to the Source Address and discard the packet;
}
else {
decrement the IPv6 Hop Limit by 1;
resubmit the packet to the IPv6 module for transmission to the
new destination;
}
}
7. Deployment Considerations
This section analyzes some deployment considerations faced by E-SRH.
Jie Expires May 16, 2021 [Page 8]
Internet-Draft Enhanced Source Routing Header November 2020
7.1. Heterogeneous Segment List
E-SRH can support a combination of various type of segments in a
single Segment List to reduce encapsulation size. This can be used
in scenarios that an E2E Segment List may across multiple domains and
each domain has different segment encapsulation style.
It is important for the border node that connected multiple domains
to use Segment sharing the same prefix with each domain as much as
possible, otherwise, a Segment that is 128 bit of IPv6 address may be
inserted in the Segment List, to provide new prefix information for
the next domain.
7.2. Independent Arguments in E-SRH
E-SRH can store independent elements as argument that has local
meaning and is used by the the immediately preceding segment.
Because the argument type of segment has only local meaning, it does
not consume the global address resources. This is very helpful for
supporting a large number of services in some networks with limited
address space.
Note that in E-SRH a Segment can also directly contain the argument
with it, i.e, in the same field. How to distinguish where the
argument exist depends on the behavior of the Segment.
7.3. ICMP Error Processing
The invoking packet in the ICMP error message may contain an E-SRH.
Since the destination address of a packet with an E-SRH changes as
each segment is processed, it may not be the destination used by the
socket or application that generated the invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
If routing header is type E-SRH
Walk to the Segment List[N] (should not be an argument or
index) which may be used as the destination address of the
invoking packet.
Jie Expires May 16, 2021 [Page 9]
Internet-Draft Enhanced Source Routing Header November 2020
7.4. Repair Path
The mechanism defined in [I-D.ietf-rtgwg-segment-routing-ti-lfa] can
be used to provide protection of nodes and links within an IGP area.
The repair path can be representd as a Segment List which can be
encoded in a separate E-SRH. The Point of Local Repair (PLR) maybe
the headend or midpoint of the original path. According to
[RFC8200], E-SRH must also not be processed, inserted, or deleted by
any node along a packet's delivery path, until the packet reaches the
node identified in the Destination Address field of the IPv6 header.
Thus, for midpoint an outer IPv6 header with its own E-SRH need to be
added to the received IPv6 packet, when the packet is delivered along
a repair path. However, it is possible for headend to encode
multiple E-SRHs within a single IPv6 header when it initiates a
packet that is delivered along a repair pat. In any case, when the
outer E-SRH is finished, the inner E-SRH is continued to be
processed. Whether it's the inner E-SRH or the outer E-SRH, in order
to achieve better compression efficiency, the first Segment (similar
to RH3) is compressed as much as possible.
[I-D.ietf-rtgwg-segment-routing-ti-lfa] also described in some cases
when the failure node or link is just the active segment, and the
method is to ignore the active segment and continue to get next
segment to keep as much as possible the traffic on the pre-failure
path. E-SRH can do this easily by simply reading the next <Type,
Cmpr, Segment> tuple from the list.
7.5. Binding to Outer Segment List
Any nodes (headend or midpoint) along the original Segment List may
also bind the packets to an outer Segment List based on local policy.
For example, the headend may steer packets along an outer Segment
List to the first Segment, and multiple E-SRHs may be encoded within
a single IPv6 header in the initated packets. A midpoint may also
steer packets along an outer Segment List to the next Segment, and an
outer IPv6 header with its own E-SRH need to be added to the received
IPv6 packet. In any case, when the outer E-SRH is finished, the
inner E-SRH is continued to be processed.
7.6. In-situ OAM
OAM and PM information from the segment endpoints can be piggybacked
in the data packet. The OAM and PM information piggybacking in the
data packets is also known as In-situ OAM (IOAM). IOAM records
operational and telemetry information in the data packet while the
packet traverses a path between two points in the network.
[I-D.ietf-ippm-ioam-data] defines the IOAM data, and
[I-D.ietf-ippm-ioam-ipv6-options] defines how to carry IOAM data in
Jie Expires May 16, 2021 [Page 10]
Internet-Draft Enhanced Source Routing Header November 2020
"option data" fields using two types of extension headers in IPv6
packets - either Hop-by-Hop Options header or Destination options
header. Next version of this document will define how IOAM data
fields are transported as part of E-SRH.
E-SRH complies with [RFC8200], and the Segment Left field strictly
represents the number of explicitly listed intermediate nodes still
to be visited before reaching the final destination. Thus, Segment
Left can be used as local index at which it is expected to record
endpoint's data in the IOAM data space.
7.7. NAT Service Funtion
A NAT service funtion SR-MPLS or SRv6 SID can be encoded in the
Segment List field of the E-SRH. The related NAT Service entity may
modify the destination address in the packets they process. At the
endpoint that associated with NAT service entity, the updated
Destination Address need to be copied back into the Segment List[N]
(i.e, the final destination) of the E-SRH. Although E-SRH contains
compressed Segments, it can walk to the last <Type, Cmpr, Segment>
tuple and write the updated address. Note that in this case the type
of last Segment must not be an argument or index, and must share
prefix with the updated address.
7.8. Operation and Maintenance
To be convenient for operation and maintenance, E-SRH provide
necessary information to enable offline tools to parse the IPv6
header and analysis Segment List, without the help of states of the
control plane. No matter how the state of the control plane vibrates
and changes, for example, the purpose of a Segment may be changed
from service A to service B, but the parsing of the packet itself is
stable and not affected. This is very convenient for network
debugging, operators can clearly know the specific Segment List
information encapsulated in E-SRH, check problems and locate them.
7.9. Upper-Layer Checksums
[RFC8200] specifies that any transport or other upper-layer protocol
that includes the addresses from the IP header in its checksum
computation must be modified for use over IPv6, to include the
128-bit IPv6 addresses. If the IPv6 packet contains a Routing
header, the Destination Address used in the pseudo-header is that of
the final destination. At the originating node, that address will be
in the last element of the Routing header; at the recipient(s), that
address will be in the Destination Address field of the IPv6 header.
Jie Expires May 16, 2021 [Page 11]
Internet-Draft Enhanced Source Routing Header November 2020
For E-SRH, at the headend, the Destination Address used in the
pseudo-header is the final destination that is before uncompression.
8. Security Considerations
The E-SRH domain is treated as a trusted domain, and the nodes
outside the E-SRH domain are not trusted. This is enforced by two
levels of access control lists:
On the ingress of E-SRH domain, any packet entering the E-SRH
domain and destined to an IPv6 address within the E-SRH domain, is
dropped.
On the transit or egress of E-SRH domain, any packet with a
destination address within the E-SRH domain but the source address
not within, is dropped.
It will block the attacks documented in [RFC5095] from outside the
E-SRH domain, including bypassing filtering devices, reaching
otherwise-unreachable Internet systems, network topology discovery,
bandwidth exhaustion, and defeating anycast.
Additionally, domains deny traffic with spoofed addresses by
implementing the recommendations in BCP 84 [RFC3704].
[RFC6554] requires RPL routers to check for loops in the SRH and drop
datagrams that contain such loops. However, for the flexibility of
Segment List programming for any scenario, E-SRH doesn't do this
check, but relevant security mechanisms to avoid tampering with
Segment List should be adopted, such as HMAC mechanism introduced in
[RFC8754].
The generation of ICMPv6 error messages may be used to attempt
denial-of-service attacks by sending an error-causing E-SRH in back-
to-back datagrams. An implementation that correctly follows
Section 2.4 of [RFC4443] would be protected by the ICMPv6 rate-
limiting mechanism.
9. Acknowledgements
TBD
10. Normative References
[I-D.ietf-ippm-ioam-data]
Brockners, F., Bhandari, S., and T. Mizrahi, "Data Fields
for In-situ OAM", draft-ietf-ippm-ioam-data-10 (work in
progress), July 2020.
Jie Expires May 16, 2021 [Page 12]
Internet-Draft Enhanced Source Routing Header November 2020
[I-D.ietf-ippm-ioam-ipv6-options]
Bhandari, S., Brockners, F., Pignataro, C., Gredler, H.,
Leddy, J., Youell, S., Mizrahi, T., Kfir, A., Gafni, B.,
Lapukhov, P., Spiegel, M., Krishnan, S., Asati, R., and M.
Smith, "In-situ OAM IPv6 Options", draft-ietf-ippm-ioam-
ipv6-options-04 (work in progress), November 2020.
[I-D.ietf-lsr-flex-algo]
Psenak, P., Hegde, S., Filsfils, C., Talaulikar, K., and
A. Gulko, "IGP Flexible Algorithm", draft-ietf-lsr-flex-
algo-13 (work in progress), October 2020.
[I-D.ietf-rtgwg-segment-routing-ti-lfa]
Litkowski, S., Bashandy, A., Filsfils, C., Decraene, B.,
Francois, P., Voyer, D., Clad, F., and P. Camarillo,
"Topology Independent Fast Reroute using Segment Routing",
draft-ietf-rtgwg-segment-routing-ti-lfa-04 (work in
progress), August 2020.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC3704] Baker, F. and P. Savola, "Ingress Filtering for Multihomed
Networks", BCP 84, RFC 3704, DOI 10.17487/RFC3704, March
2004, <https://www.rfc-editor.org/info/rfc3704>.
[RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", STD 89,
RFC 4443, DOI 10.17487/RFC4443, March 2006,
<https://www.rfc-editor.org/info/rfc4443>.
[RFC5095] Abley, J., Savola, P., and G. Neville-Neil, "Deprecation
of Type 0 Routing Headers in IPv6", RFC 5095,
DOI 10.17487/RFC5095, December 2007,
<https://www.rfc-editor.org/info/rfc5095>.
[RFC6550] Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
Low-Power and Lossy Networks", RFC 6550,
DOI 10.17487/RFC6550, March 2012,
<https://www.rfc-editor.org/info/rfc6550>.
Jie Expires May 16, 2021 [Page 13]
Internet-Draft Enhanced Source Routing Header November 2020
[RFC6554] Hui, J., Vasseur, JP., Culler, D., and V. Manral, "An IPv6
Routing Header for Source Routes with the Routing Protocol
for Low-Power and Lossy Networks (RPL)", RFC 6554,
DOI 10.17487/RFC6554, March 2012,
<https://www.rfc-editor.org/info/rfc6554>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", STD 86, RFC 8200,
DOI 10.17487/RFC8200, July 2017,
<https://www.rfc-editor.org/info/rfc8200>.
[RFC8279] Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
Przygienda, T., and S. Aldrin, "Multicast Using Bit Index
Explicit Replication (BIER)", RFC 8279,
DOI 10.17487/RFC8279, November 2017,
<https://www.rfc-editor.org/info/rfc8279>.
[RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
Decraene, B., Litkowski, S., and R. Shakir, "Segment
Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
July 2018, <https://www.rfc-editor.org/info/rfc8402>.
[RFC8754] Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J.,
Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header
(SRH)", RFC 8754, DOI 10.17487/RFC8754, March 2020,
<https://www.rfc-editor.org/info/rfc8754>.
Author's Address
Han Jie
ZTE Corporation
China
Email: han.jie1@zte.com.cn
Jie Expires May 16, 2021 [Page 14]