Network Working Group T. Hardie, Ed.
Internet-Draft May 02, 2017
Intended status: Informational
Expires: November 3, 2017
Path signals
draft-hardie-path-signals-01
Abstract
TCP's state mechanics uses a series of well-known messages that are
exchanged in the clear. Because these are visible to network
elements on the path between the two nodes setting up the transport
connection, they are often used as signals by those network elements.
In transports that do not exchange these messages in the clear, on-
path network elements lack those signals. This document discusses
the nature of the signals as they are seen by on-path elements and
reflects on best practices for transports which encrypt their state
mechanics.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 3, 2017.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Hardie Expires November 3, 2017 [Page 1]
Internet-Draft pathsignals May 2017
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
3. Signals Type Inferred . . . . . . . . . . . . . . . . . . . . 3
3.1. Session establishment . . . . . . . . . . . . . . . . . . 3
3.1.1. Session identity . . . . . . . . . . . . . . . . . . 3
3.1.2. Routability and Consent . . . . . . . . . . . . . . . 4
3.1.3. Resource Requirements . . . . . . . . . . . . . . . . 4
3.2. Network Measurement . . . . . . . . . . . . . . . . . . . 4
3.2.1. Path Latency . . . . . . . . . . . . . . . . . . . . 4
3.2.2. Path reliability and consistency . . . . . . . . . . 4
4. Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.1. Do not restore these signals . . . . . . . . . . . . . . 5
4.2. Replace these with network layer signals . . . . . . . . 5
4.3. Replace these with per-transport signals . . . . . . . . 5
4.4. Create a set of signals common to multiple transports . . 5
5. Recommendation . . . . . . . . . . . . . . . . . . . . . . . 6
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6
7. Security Considerations . . . . . . . . . . . . . . . . . . . 6
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 7
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
9.1. Normative References . . . . . . . . . . . . . . . . . . 7
9.2. Informative References . . . . . . . . . . . . . . . . . 7
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 8
1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Introduction
TCP [RFC0793] uses handshake messages to establish, maintain, and
close connections. While these are primarily intended to create
state between two communicating nodes, these handshake messages are
visible to network elements along the path between them. It has been
common over time for certain network elements to treat the exchanged
messages as signals which related to their own functions.
A firewall may, for example, create a rule that allows traffic from a
specific host and port to enter its network when the connection was
Hardie Expires November 3, 2017 [Page 2]
Internet-Draft pathsignals May 2017
initiated by a host already within the network. It may subsequently
remove that rule when the communication has ceased. In the context
of TCP handshake, it sets up the pinhole rule on seeing the initial
TCP SYN acknowledged and then removes it upon seeing a RST or FIN &
ACK exchange. Note that in this case it does nothing to re-write any
portion of the TCP packet; it simply enables a return path that would
otherwise have been blocked.
When a transport encrypts the headers it uses for state mechanics,
the signal path elements inferred from examination is no longer
available. Their behavior in its absence will depend on which signal
is not available, on the default behavior configured by the path
element administrator, and by the security posture of the network as
a whole.
3. Signals Type Inferred
The following list of signals which may be inferred from transport
state messages includes those which may be exchanged during sessions
establishment and those which derive from the ongoing flow. Some of
these signals are derived from the direct examination of packet
trains, such as using a sequence number gap pattern to infer network
reliability; others are derived from association, such as inferring
network latency by timing a flow's packet inter-arrival times. This
list is not exhaustive, and it is not the full set of effects due to
encrypting data and metadata in flight. Note as well that because
these are derived from inferenece, they do not include any path
signals which would not be relevant to the end point state machines;
indeed, an inference-based system cannot send such signals.
3.1. Session establishment
One of the most basic inferences made by examination of transport
state is that a packet will be part of an ongoing flow; that is, an
established session will continue until messages are received that
terminate it. Path elements may then make subsidiary inferences
related to the session.
3.1.1. Session identity
Path elements that track session establishment will typically create
a session identify for the flow, commonly using a tuple of the
visible information in the packet headers. This is then used to
associate other information with the
Hardie Expires November 3, 2017 [Page 3]
Internet-Draft pathsignals May 2017
3.1.2. Routability and Consent
A second common inference is that the session establishment provides
is that the communicating pair of hosts can each reach each other and
are interested in continuing communication. The firewall example
given above is a consequence of the inference of consent; because the
internal host initiates the connection, it is presumed to consent to
return traffic. That, in turn justifies the pinhole.
3.1.3. Resource Requirements
An additional common inference is that network resources will be
required for the session. These may be requirements within the
network element itself, such as table entry space for a firewall or
NAT; they may also be communicated by the network element to other
systems. For networks which use resource reservations, this might
result in reservation of radio air time, energy, or network capacity.
3.2. Network Measurement
Some network elements will also use transport messages to engage in
measurement of the paths which are used by flows on their network.
The list of measurements below is illustrative, not exhaustive.
3.2.1. Path Latency
There are several ways in which a network element may measure path
latency using transport messages, but two common ones are examining
exposed timestamps and associating sequence numbers with a local
timer. These measurements are necessarily limited to measuring only
the portion of the path between the system which assigned the
timestamp or sequence number and the network element.
3.2.2. Path reliability and consistency
A network element may also measure the reliability of a particular
path by examining sessions which expose sequence numbers;
retransmissions and gaps are then associated with the path segments
on which they might have occurred.
4. Options
The set of options below are alternatives which optimize very
different things. Though it comes to a preliminary conclusion, this
draft intends to foster a discussion of those tradeoffs and any
discussion of them must be understood as preliminary.
Hardie Expires November 3, 2017 [Page 4]
Internet-Draft pathsignals May 2017
4.1. Do not restore these signals
It is possible, of course, to do nothing. The transport messages
were not necessarily intended for consumption by on-path network
elements and encrypting them so they are not visible may be taken by
some as a benefit. Each network element would then treat packets
without these visible elements according to its own defaults. While
our experience of that is not extensive, one consequence has been
that state tables for flows of this type are generally not kept as
long as those for which sessions are identifiable. The result is
that heartbeat traffic must be maintained to keep any bindings (e.g.
NAT or firewall) from early expiry. When those bindings are not
kept, methods like QUIC's connection-id [I-D.ietf-quic-transport] may
be necessary to allow load blancers or other systems to continue to
maintain a flow's path to the appropriate peer.
4.2. Replace these with network layer signals
It would be possible to replace these implicit signals with explicit
signals at the network layer. Though IPv4 has relatively few
facilities for this, IPv6 hop-by-hop headers [RFC7045] might suit
this purpose. Further examination of the deployability of these
headers may be required.
4.3. Replace these with per-transport signals
It is possible to replace these implicit signals with signals that
are tailored to specific transports, just as the initial signals are
derived primarily from TCP. There is a risk here that the first
transport which develops these will be reused for many purposes
outside its stated purpose, simply because it traverses NATs and
firewalls better than other traffic. If done with an explicit intent
to re-use the elements of the solution in other transports, the risk
of ossification might be slightly lower.
4.4. Create a set of signals common to multiple transports
Several proposals use UDP[RFC0768] as a demux layer, onto which new
transport semantics are layered. For those transports, it may be
possible to build a common signalling mechanism and set of signals,
such as that proposed in "Transport-Independent Path Layer State
Management" [I-D.trammell-plus-statefulness].
This may be taken as a variant of the re-use of common elements
mentioned in the section above, but it has a greater chance of
avoiding the ossification of the solution into the first moving
protocol.
Hardie Expires November 3, 2017 [Page 5]
Internet-Draft pathsignals May 2017
5. Recommendation
Fundamentally, this paper recommends that implicit signals should be
replaced with explicit signals, but that a signal should be exposed
to the path only when the signal's originator intends that it be used
by the network elements on the path. For many flows, that may result
in signal being absent, but it allows them to be present when needed.
Discussion of the appropriate mechanism(s) for these signals is
continuing but, at minimum, any method should meet the principles set
out in the security considerations below.
6. IANA Considerations
This document contains no requests for IANA.
7. Security Considerations
Addition of visible signals to the path allows network elements along
the path to act. If the network element is controlled by an
attacker, those actions can include dropping, delaying, or
mishandling the constituent packets of a flow.
Note that actions that do not benefit the flow or the network may be
perceived as an attack even if they are conducted by a responsible
network element. Designing a system that minimizes the ability to
act on signals at all by removing as many signals as possible may
reduce this possibility. This approach also comes with risks,
principally that the actions will continue to take place on an
arbitrary set of flows.
Addition of visible signals to the path also increases the
information available to an observer and may, when the information
can be linked to a node or user, reduce the privacy of the user.
This document recommends three basic principles:
o Cryptographic contexts should be available on any flow, derived
from ubiquitous end-system cryptographic capabilities.
o Anything exposed to the path should be done with the intent that
it be used by the network elements on the path.
o Intermediate path elements should not add visible signals which
identify the user, origin node, or origin network
[I-D.hardie-privsec-metadata-insertion].
Hardie Expires November 3, 2017 [Page 6]
Internet-Draft pathsignals May 2017
8. Acknowledgements
In addition to the editor listed above, this document incorporates
contributions from Brian Trammel, Mirja Kuehlwind, and Joe
Hildebrand. These ideas were also discussed at the PLUS BoF,
sponsored by Spencer Dawkins. The ideas around the use of IPv6 hop-
by-hop headers as a network layer signal benefited from discussions
with Tom Herbert. The description of UDP as a demuxing protocol
comes from Stuart Cheshire.
All errors are those of the editor.
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
9.2. Informative References
[I-D.hardie-privsec-metadata-insertion]
Hardie, T., "Design considerations for Metadata
Insertion", draft-hardie-privsec-metadata-insertion-08
(work in progress), March 2017.
[I-D.ietf-quic-transport]
Iyengar, J. and M. Thomson, "QUIC: A UDP-Based Multiplexed
and Secure Transport", draft-ietf-quic-transport-02 (work
in progress), March 2017.
[I-D.trammell-plus-statefulness]
Kuehlewind, M., Trammell, B., and J. Hildebrand,
"Transport-Independent Path Layer State Management",
draft-trammell-plus-statefulness-03 (work in progress),
March 2017.
[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
DOI 10.17487/RFC0768, August 1980,
<http://www.rfc-editor.org/info/rfc768>.
[RFC0793] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, DOI 10.17487/RFC0793, September 1981,
<http://www.rfc-editor.org/info/rfc793>.
Hardie Expires November 3, 2017 [Page 7]
Internet-Draft pathsignals May 2017
[RFC7045] Carpenter, B. and S. Jiang, "Transmission and Processing
of IPv6 Extension Headers", RFC 7045,
DOI 10.17487/RFC7045, December 2013,
<http://www.rfc-editor.org/info/rfc7045>.
Author's Address
Ted Hardie (editor)
Email: ted.ietf@gmail.com
Hardie Expires November 3, 2017 [Page 8]