SPRING S. Hegde
Internet-Draft S. Sangli
Intended status: Standards Track M. Srivastava
Expires: December 4, 2020 Juniper Networks Inc.
X. Xu
Alibaba Inc.
June 2, 2020
BGP-LS Extensions for Inter-AS TE using EPE based mechanisms
draft-hegde-idr-bgp-ls-epe-inter-as-03
Abstract
In certain network deployments, a single operator has multiple
Autonomous Systems(AS) to facilitate ease of management. A multiple
AS network design could also be a result of network mergers and
acquisitions. In such scenarios, a centralized Inter-domain TE
approach could provide most optimal allocation of resources and the
most controlled path placement. BGP-LS-EPE
[I-D.ietf-idr-bgpls-segment-routing-epe] describes an extension to
BGP Link State (BGP-LS) for the advertisement of BGP Peering Segments
along with their BGP peering node and inter-AS link information, so
that efficient BGP Egress Peer Engineering (EPE) policies and
strategies can be computed based on Segment Routing. This document
describes extensions to the BGP-LS EPE to enable it to be used for
inter-AS Traffic-Engineering (TE) purposes.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
Hegde, et al. Expires December 4, 2020 [Page 1]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
This Internet-Draft will expire on December 4, 2020.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Reference Topology . . . . . . . . . . . . . . . . . . . . . 3
3. Fast Reroute Label . . . . . . . . . . . . . . . . . . . . . 4
4. TE Link attributes of PeerNode SID . . . . . . . . . . . . . 5
5. TE Link attributes of PeerAdj SID . . . . . . . . . . . . . . 5
6. Link address TLV . . . . . . . . . . . . . . . . . . . . . . 6
7. Example Advertisements . . . . . . . . . . . . . . . . . . . 7
8. Backward Compatibility . . . . . . . . . . . . . . . . . . . 9
9. Security Considerations . . . . . . . . . . . . . . . . . . . 9
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 9
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 10
12.1. Normative References . . . . . . . . . . . . . . . . . . 10
12.2. Informative References . . . . . . . . . . . . . . . . . 10
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10
1. Introduction
Segment Routing (SR) leverages source routing. A node steers a
packet through a controlled set of instructions, called segments, by
prepending the packet with an SR header with segment identifiers
(SID). A SID can represent any instruction, topological or service-
based. SR segments allows to enforce a flow through any topological
path or service function while maintaining per-flow state only at the
ingress node of the SR domain.
As there is no per-path state in the network, the bandwidth
management for the paths is expected to be handled by a centralized
entity which has a complete view of:
Hegde, et al. Expires December 4, 2020 [Page 2]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
1. Up-to-date topology of the network
2. Resources, States and Attributes of links and nodes of the
network
3. Run-time utilization/availability of resources
The BGP Link-State extensions provide mechanisms whereby link-state
and TE information can be propagated n a network and a consumer of
such BGP LS updates may build topology, provide bandwidth calendering
and other traffic engineering services. The centralized entity can
be such a consumer (also referred to as controller). In the case of
multi-AS networks, the controller needs to learn the per-AS network
information and the inter-AS link information thus arriving at a
consolidated Traffic Engineering Database which can be used to
compute end-to-end Traffic Engineering Path. The controller can
learn the topology, link-state and TE information from each of the AS
networks either by participating in their IGPs or by listening to BGP
LS updates [RFC7752]. Similar information about the inter-AS links
can be learnt via BGP-LS EPE [I-D.ietf-idr-bgpls-segment-routing-epe]
along with extensions defined in this documet.
2. Reference Topology
The controller learns TE attributes of all the links, including the
inter-AS links and uses the attributes to compute constrained paths.
The controller should be able to correlate the inter-AS links for
bidirectional connectivity from both ASes.
Hegde, et al. Expires December 4, 2020 [Page 3]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
+----------+
|Controller|
+----------+
|
|----------|
+---------+ +------+
| | | |
| H B------D G
| | +---/| AS 2 |\ +------+
| |/ +------+ \ | |---L/8
A AS1 C---+ \| |
| |\\ \ +------+ /| AS 4 |---M/8
| | \\ +-E |/ +------+
| X | \\ | K
| | +===F AS 3 |
+---------+ +------+
Figure 1: Reference Diagram
The reference diagram from
[I-D.ietf-spring-segment-routing-central-epe] represents multiple
Autonomous Systems connected to each other. When the Multiple ASes
belong to same operator and are organised into separate domains for
operational purposes, it is advantageous to support Traffic-
Engineering across the ASes including the inter-AS links. The
controller has visibility of all of the ASes by means of IGP topology
exported via BGP-LS [RFC7752], or other means. In addition, the
inter-AS links and the labels associated with the inter-AS links are
exported via [I-D.ietf-idr-bgpls-segment-routing-epe]. The
controller needs to correlate the information acquired from all of
the ASes, including the inter-AS links in order to get a view of the
unified topology so that it can build end-to-end Traffic-Engineered
paths.
3. Fast Reroute Label
[I-D.ietf-spring-segment-routing-central-epe] section 3.6 describes
mechanisms to provide Fast Reroute (FRR) protection for the EPE
Labels. The BGP-LS EPE [I-D.ietf-idr-bgpls-segment-routing-epe]
describes "B" bit to indicate that a PeerNodeSID or PeerAdjSID is
eligible for backup. However, it does not specify what is the
behaviour when the failure kicks-in. The controller needs to know
which links are used for protection so that admission control and
failure simulation can be done effectively and appropriate inter-AS
links used for path construction.
Hegde, et al. Expires December 4, 2020 [Page 4]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
This document defines a new flag "F" in the Peering SIDs TLV to
indicate a SID as an FRR SID. With the "F" flag set, the protection
for any peering SID can be specified using another PeerAdjSID,
PeerNodeSID or PeerSetSID to the controller. If the protection is
achieved by fallback to local IP lookup, FRR SID SHOULD not be
advertised. The link(s) represented by the FRR SID will carry the
traffic when there is a failure. These SIDs are included as an FRR
SIDs in the peerAdjSID, PeerNodeSID and PeerSetSID advertisements.
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|V|L|B|P|F|Rsvd |
+-+-+-+-+-+-+-+-+
Figure 2: Peering SID TLV Flags Format
* F-Flag: FRR Label Flag: If set, the peer SID where the FRR Label
appears is using backup links represented by FRR Label.
4. TE Link attributes of PeerNode SID
In any eBGP deployment, the peering session can be either single-hop
of multi-hop. For single-hop eBGP sessions, the peering address is
that of the directly attached interface to which the session is
pinned down. For multi-hop eBGP session, the peering adress is
reachable over more than one interface and that the peering session
is not pinned down to any of the directly attached interfaces.
A Peer Node Segment is a segment describing a peer, including the SID
(PeerNodeSID) allocated to it. The link descriptors for the
PeerNodeSID include the addresses used by the BGP session encoded
using TLVs as defined in [RFC7752]. Since the eBGP session can be
either single-hop or multi-hop, the IP address used by BGP session as
local/neigbour is not sufficient to identify the underlaying
interface(s). Also, the controller needs to know the links
associated with the PeerNodeSID, to be able derive TE link
attributes. This can be achieved by including the interface local
and remote addresses in the Link attributes in PeerNodeSID NLRI.
This document defines a new link attribute TLV name Interface Address
TLV. PeerNodeSID NLRI MAY optionally include Interface Address TLV.
5. TE Link attributes of PeerAdj SID
PeerAdjSID MUST be advertised for each inter-AS link for the purposes
of inter-AS TE. The PeerAdjSID should contain link TE attributes
such as bandwidth, admin-group etc. The PeerAdjSID should also
Hegde, et al. Expires December 4, 2020 [Page 5]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
contain the local and remote interface IPv4/IPv6 addresses which is
used for correlating the links. PeerNodeSID SHOULD contain the
additional attribute of link local address which is used by the
controller to find corresponding PeerAdjSID and hence the
corresponding link TE attributes.
A peerAdj segment carries mandatory link descriptors as local and
remote link id. Remote link id of the neighboring ASBR is not
readily available. [I-D.ietf-idr-bgpls-segment-routing-epe] suggests
to carry the value '0' for the remote link id. The Controller needs
to associate the links in both directions to effectively handle
failure notifications and for this purpose a unque remote link is
necessary. The remote link ID cannot be manually configured on the
router as the link-ids generally change over router reboot etc and
hence manual configuration is operationally very difficult to manage.
This document mandates advertisement of local and remote iterface
addresses for the inetr-AS TE purposes.
The Unnumbered interface is not in the scope of this document.
6. Link address TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Type = TBD | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| No.of IPV4 interface pairs |No. of IPv6 interface Pairs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Local Interface address1 (4/16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Remote Interface address1 (4/16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Local Interface address2 (4/16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Link Address TLV carried as attribute
Type : TBD
Length : variable based on ipv4/ipv6 interface address
Hegde, et al. Expires December 4, 2020 [Page 6]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
Number of IPv4 interface pairs:
Number of IPv6 interface pairs:
There may be a number of parallel interfaces and few or all of them
may be used for the PeerNodeSID. These interfaces may have both IPV4
and IPV6 address or some interfaces may be IPv4 only and some IPv6
only. The total number of IPv4 and IPv6 interface address count is
carried seperately in above fields.
Local Interface Address :
The interface local address ipv4/ipv6 which corresponds to the
PeerNodeSID MUST be specified. For IPv4,this field is 4 octets; for
IPv6, this field is 16 octets.
Remote Interface Address :
The interface remote address ipv4/ipv6 which corresponds to the
PeerNodeSID MUST be specified. For IPv4,this field is 4 octets; for
IPv6, this field is 16 octets.
There can be multiple Layer 3 interfaces on which a peerNodeSId
loadbalances the traffic. All such interfaces local/remote address
MUST be included when a Link address TLV is added.When a single Layer
3 interface consists of multiple addresses or when a link has both
IPv4 and IPv6 addresses configured, It is sufficient to include one
such pair (either IPV4 or IPv6)address for the PeerNodeSID
advertisement. When a PeerNodeSID load-balances over few interfaces
with IPv4 only address and few interfaces with IPv6 address then the
Link address TLV should list all IPv4 address pairs together followed
by IPv6 address pairs.
7. Example Advertisements
The below diagram represents two ASBR routers and inter-AS links
between them. The inter-AS links could be connected via switches L1
and L2 as shown in the diagram or via Point-to-point links A2->B2,
A3->B3 as shown in the diagram below. In the below example, lets
assume peerNodeSID 1 is configured to use peerAdjSID 10002 then
PeerNodeSID 1 will have the B bit set which means the PeerNodeSID 1
is eligible for backup. Label 10002 is added to the PeerNodeSID with
a "F" bit set, which means 10002 is a backup for PeerNodeSID 1.
+------------------------------------------------------------------+
| PeerNodeSID PeerAdjSID |
| |
Hegde, et al. Expires December 4, 2020 [Page 7]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
|+-+----------------------------+ +-+-----------------------------+|
||N|Loc Node Descr: AS1:A | |N|Loc Node Descr: AS1:A||
||L|Rmt Node Descr: AS2:B | |L|Rmt Node Descr: AS2:B||
||R|Link Descr: lo1:lo1 | |R|Link Descr LinkLocRmtID: 1:0 ||
||I| | |I|Link IP (mandatory): A1:B1||
|+-+----------------------------+ +-+-----------------------------+|
||A|Intf Adress(new): A1:B1 | |A|PeerAdjSID: 10001 ||
||T| A2:B2 | |T|SRLG ||
||T|PeerNodeSID: 1 | |T|affinity group ||
||R|PeerSetSID (optional) | |R|MaxB/W ||
|+-+----------------------------+ +-+-----------------------------+|
|+-+----------------------------+ +-+-----------------------------+|
||N|Loc Node Descr: AS1:A | |N|Loc Node Descr: AS1:A||
||L|Rmt Node Descr: AS2:B | |L|Rmt Node Descr: AS2:B||
||R|Link Descr: lo2:lo2 | |R|Link Descr LinkLocRmtID: 2:0 ||
||I| | |I|Link IP (mandatory): A2:B2||
|+-+----------------------------+ +-+-----------------------------+|
||A|Intf addr (new): A1:B1 | |A|PeerAdjSID: 10002 ||
||T| : A3:B3 | |T|SRLG ||
||T|PeerNodeSID: 2 | |T|affinity group ||
||R|PeerSetSID (optional) | |R|MaxB/W ||
|| | | | |Unused B/W ||
|+-+----------------------------+ +-+-----------------------------+|
|+-+----------------------------+ +-+-----------------------------+|
||N|Loc Node Descr: AS1:A | |N|Loc Node Descr: AS1:A||
||L|Rmt Node Descr: AS2:B | |L|Rmt Node Descr: AS2:B||
||R|Link Descr: A3:B3 | |R|Link Descr LinkLocRmtID: 2:0 ||
||I| | |I|Link IP (mandatory): A3:B3||
|+-+----------------------------+ +-+-----------------------------+|
|| |PeerNodeSID: 3 | |A|PeerAdjSID: 10103 ||
||A|SRLG | |T|SRLG ||
||T|affinity group | |T|affinity group ||
||T|MaxB/W | |R|MaxB/W ||
||R|Unused B/W | | |Unused B/W ||
|| |... | | | ||
|+-+----------------------------+ +-+-----------------------------+|
+------------------------------------------------------------------+
^
BGP-LS EPE |
+----------> w/ InerDomain -------+
| extensions
|
| +---------------------------------mh-eBGP--------------------+
| | |
| | +-----------------------------mh-eBGP----------------+ |
| | | | |
+--+---+-----+ static lo1 --> +-----+ +-----+ +-----+---+--+
| v v | static lo2 --> | L2 | | L2 | | v v |
Hegde, et al. Expires December 4, 2020 [Page 8]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
| lo1 lo2 A1*------------------| swt |--->| swt |----*B1 lo2 lo1 |
| | +-----+ +-----+ | |
| | | |
| | | |
| RtR A | static lo1 --> | RtR B |
| A2*----------------------------------------*B2 |
| | | |
| | static lo2 --> | |
| A3*----------------------------------------*B3 |
| | | |
+-----------+^ ^+-----------+
| |
| |
+-------------------eBGP-----------------+
Figure 4: Example Advertisements
8. Backward Compatibility
The extension proposed in this document is backward compatible with
procedures described in [I-D.ietf-idr-bgpls-segment-routing-epe] and
[I-D.ietf-spring-segment-routing-central-epe]
9. Security Considerations
TBD
10. IANA Considerations
New attribute TLV in BGP-LS Node Descriptor, Link Descriptor, Prefix
Descriptor, and Attribute TLVs registry
+-----------+-----------------------+--------------+------------------+
| TLV Code | Description | IS-IS TLV | Reference |
| Point | | /Sub-TLV | (RFC/Section) |
+-----------+-----------------------+--------------+------------------+
| TBD | Link address TLV | NA | This draft |
+---------------------------------------------------------------------+
Figure 5: IANA code point
11. Acknowledgements
Thanks to Julian Lucek and Rafal Jan Szarecki for careful review and
suggestions.
Hegde, et al. Expires December 4, 2020 [Page 9]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
12. References
12.1. Normative References
[I-D.ietf-idr-bgpls-segment-routing-epe]
Previdi, S., Talaulikar, K., Filsfils, C., Patel, K., Ray,
S., and J. Dong, "BGP-LS extensions for Segment Routing
BGP Egress Peer Engineering", draft-ietf-idr-bgpls-
segment-routing-epe-19 (work in progress), May 2019.
[I-D.ietf-spring-segment-routing-central-epe]
Filsfils, C., Previdi, S., Dawra, G., Aries, E., and D.
Afanasiev, "Segment Routing Centralized BGP Egress Peer
Engineering", draft-ietf-spring-segment-routing-central-
epe-10 (work in progress), December 2017.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7752] Gredler, H., Ed., Medved, J., Previdi, S., Farrel, A., and
S. Ray, "North-Bound Distribution of Link-State and
Traffic Engineering (TE) Information Using BGP", RFC 7752,
DOI 10.17487/RFC7752, March 2016,
<https://www.rfc-editor.org/info/rfc7752>.
12.2. Informative References
[RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
Decraene, B., Litkowski, S., and R. Shakir, "Segment
Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
July 2018, <https://www.rfc-editor.org/info/rfc8402>.
Authors' Addresses
Shraddha Hegde
Juniper Networks Inc.
Exora Business Park
Bangalore, KA 560103
India
Email: shraddha@juniper.net
Hegde, et al. Expires December 4, 2020 [Page 10]
Internet-Draft BGP-LS extensions for Inter-AS TE using EPE June 2020
Srihari Sangli
Juniper Networks Inc.
Exora Business Park
Bangalore, KA 560103
India
Email: ssangli@juniper.net
Mukul Srivastava
Juniper Networks Inc.
Email: msri@juniper.net
Xiaohu Xu
Alibaba Inc.
Beijing
China
Email: xiaohu.xxh@alibaba-inc.com
Hegde, et al. Expires December 4, 2020 [Page 11]