Network Working Group                                        B. Trammell
Internet-Draft                                             M. Kuehlewind
Intended status: Informational                                ETH Zurich
Expires: May 9, 2019                                   November 05, 2018


                  The Wire Image of a Network Protocol
                        draft-iab-wire-image-01

Abstract

   This document defines the wire image, an abstraction of the
   information available to an on-path non-participant in a networking
   protocol.  This abstraction is intended to shed light on the
   implications on increased encryption has for network functions that
   use the wire image.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on May 9, 2019.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.



Trammell & Kuehlewind      Expires May 9, 2019                  [Page 1]


Internet-Draft                 Wire Image                  November 2018


1.  Introduction

   A protocol specification defines a set of behaviors for each
   participant in the protocol: which lower-layer protocols are used for
   which services, how messages are formatted and protected, which
   participant sends which message when, how each participant should
   respond to each message, and so on.

   Implicit in a protocol specification is the information the protocol
   radiates toward nonparticipant observers of the messages sent among
   participants, often including participants in lower layer protocols.
   Any information that has a clear definition in the protocol's message
   format(s), or is implied by that definition, and is not
   cryptographically confidentiality-protected can be unambiguously
   interpreted by those observers.  This information comprises the
   protocol's wire image, which we define and discuss in this document.

   It is the wire image, not the protocol's specification, that
   determines how third parties on the network paths among protocol
   participants will interact with that protocol.

   The increasing deployment of transport-layer security [RFC8226] to
   protect application-layer headers and payload, as well as the
   definition and deployment of QUIC [QUIC], a transport protocol which
   encrypts most of its own control information, bring new relevance to
   this question.  QUIC is, in effect, the first IETF-defined transport
   protocol to take care of the minimization of its own wire image, to
   prevent ossification and improve end-to-end privacy by reducing
   information radiation.

   The flipside of this trend is the impact of a less visible wire image
   on various functions driven by third-party observation of the wire
   image.  In contrast to ongoing discussions about this tussle, this
   draft treats the wire image as a pure abstraction, with the hope that
   it can shed some light on these discussions.

2.  Definition

   The wire image of the set of protocols in use for a given
   communication is the view of that set of protocols as observed by an
   entity not participating in the communication.  It is the sequence of
   packets sent by each participant in the communication, including the
   content of those packets and metadata about the observation itself:
   the time at which each packet is observed, and the vantage point of
   the observer.






Trammell & Kuehlewind      Expires May 9, 2019                  [Page 2]


Internet-Draft                 Wire Image                  November 2018


3.  Discussion

   This definition illustrates some important properties of the wire
   image.

   Key is that the wire image is not limited to merely "the unencrypted
   bits in the header".  In particular, the metadata, such as sequences
   of interpacket timing and packet sizes, can also be used to infer
   other parameters of the behavior of the protocols in use, or to
   fingerprint protocols and/or specific implementations of those
   protocols; see Section 3.2.

   An important implication of this property is that a protocol which
   uses confidentiality protection for the headers it needs to operate
   can be deliberately designed to have a specified wire image that is
   separate from that machinery; see Section 4.  Note that this is a
   capability unique to encrypted protocols.  Parts of a wire image may
   also be made visible to devices on path, but immutable through end-
   to-end integrity protection; see Section 3.3.

   Portions of the wire image of a protocol stack that are neither
   confidentiality-protected nor integrity-protected are writable by
   devices on the path(s) between the endpoints using the protocols.  A
   protocol with a wire image that is largely writable operating over a
   path with devices that understand the semantics of the protocol's
   wire image can modify it, in order to induce behaviors at the
   protocol's participants.  TCP is one such protocol in the current
   Internet.

   The term "wire image" can be applied in different scopes: the wire
   image of a single packet refers to the information derivable from
   observing that one packet in isolation; the wire image of a single
   protocol refers to the information derivable from observing only the
   headers belonging to that protocol on a sequence of packets, in
   isolation from other protocols in use for a communication.  See
   Section 3.1 for more.

   For a given packet observed at a given point in the network, the wire
   image contains information from the entire stack of protocols in use
   at that observation point.  This implies that the wire image depends
   on the observer as well: each observer may see a slightly different
   image of the same communication.

   In this document, we assume that only information at the transport
   layer and above is delivered end-to-end, and focus on the "Internet"
   wire image: that portion of the wire image at the network layer and
   above.  While confidentiality and integrity protection may be added
   at multiple layers in the stack, MAC-layer integrity and



Trammell & Kuehlewind      Expires May 9, 2019                  [Page 3]


Internet-Draft                 Wire Image                  November 2018


   confidentiality protection do not prevent modification by the devices
   terminating those security associations, or by devices on different
   segments of the path.

3.1.  The Extent of the Wire Image

   While we begin this definition as the properties of a sequence of
   packets in isolation, this is not how wire images are typically used
   by passive observers.  A passive observer will generally consider the
   union of all the information in the wire image in all the packets
   generated by a given conversation.

   Similarly, the wire image of a single protocol is rarely seen in
   isolation.  The dynamics of the application and network stacks on
   each endpoint use multiple protocols for any higher level task.  Most
   protocols involving user content, for example, are often seen on the
   wire together with DNS traffic; the information from the wire image
   from each protocol in use for a given communication can be correlated
   to infer information about the dynamics of the overlying application.

   Information from protocol wire images is also not generally used on
   its own, but is rather additionally correlated with other context
   information available to the observer: e.g. information about other
   communications engaged in by each endpoint, information about the
   implementations of the protocols at each endpoint, information about
   the network and internetwork topology near those endpoints, and so
   on.  This context can be used together with information from the wire
   image to reach more detailed inferences about endpoint and end-user
   behavior.

   Note also that the wire image is multidimensional.  This implies that
   the name "image" is not merely metaphorical, and that general image
   recognition techniques may be applicable to extracting patterns and
   information from it.

3.2.  Obscuring timing and sizing information

   Cryptography can protect the confidentiality of a protocol's headers,
   to the extent that forwarding devices do not need the
   confidentiality-protected information for basic forwarding
   operations.  Ciphersuites and other transmission techniques designed
   to prevent timing analysis can also be applied at the sender to
   reduce the information content of the metadata portion of the wire
   image.  However, there are limits to these techniques.  Packets
   cannot be made smaller than their information content, sent faster
   than processing time requirements at the sender allow, or transmitted
   through the network faster than a factor less than one of the speed
   of light.  Since these techniques operate at the expense of bandwidth



Trammell & Kuehlewind      Expires May 9, 2019                  [Page 4]


Internet-Draft                 Wire Image                  November 2018


   efficiency and latency, they are also limited to the application's
   tolerance for latency and bandwidth inefficiency.

3.3.  Integrity Protection of the Wire Image

   Adding end-to-end integrity protection to portions of the wire image
   makes it impossible for on-path devices to modify them without
   detection by the endpoints, which can then take action in response to
   those modifications, making these portions of the wire image
   effectively immutable.  However, they can still be observed by
   devices on path.  This allows the creation of signals intended by the
   endpoints solely for the consumption of these on-path devices.

   Integrity protection can only practically be applied to the sequence
   of bits in each packet, which implies that a protocol's visible wire
   image cannot be made completely immutable in a packet-switched
   network.  Interarrival timings, for instance, cannot be easily
   protected, as the observable delay sequence is modified as packets
   move through the network and experience different delays on different
   links.  Message sequences are also not practically protectable, as
   packets may be dropped or reordered at any point in the network, as a
   consequence of the network's operation.  Intermediate systems with
   knowledge of the protocol semantics in the readable portion of the
   wire image can also purposely delay or drop packets in order to
   affect the protocol's operation.

4.  Engineering the Wire Image

   Understanding the nature of a protocol's wire image allows it to be
   engineered.  The general principle at work here, observed through
   experience with deployability and non-deployability of protocols at
   the network and transport layers in the Internet, is that all
   observable parts of a protocol's wire image will eventually be used
   by devices on path; consequently, changes or future extensions that
   affect the observable part of the wire image become difficult or
   impossible to deploy.

   A network function which serves a purpose useful to its deployer will
   use the information it needs from the wire image, and will tend to
   get that information from the wire image in the simplest way
   possible.

   For example, consider the case of the ubiquitous TCP [RFC0793]
   transport protocol.  As described in [PATH-SIGNALS], several key in-
   network functions have evolved to take advantage of implicit signals
   in TCP's wire image, which, as TCP provides neither integrity or
   confidentiality protection for its headers, is inseparable from its
   internal operation.  Some of these include:



Trammell & Kuehlewind      Expires May 9, 2019                  [Page 5]


Internet-Draft                 Wire Image                  November 2018


   o  Determining return routability and consent: For example, TCP's
      wire image contains both an implicit indication that the sender of
      a packet is at least on the path toward its source address (in the
      acknowledgement number during the handshake), as well as an
      implicit indication that a receiving device consents to continue
      communication.  These are used by stateful network firewalls.

   o  Measuring loss and latency: For example, examining the sequence of
      TCP's sequence and acknowledgement numbers, as well as the ECN
      [RFC3168] control bits allows the inference of congestion, loss
      and retransmission along the path.  The sequence and
      acknowledgement numbers together with the timestamp option
      [RFC7323] allow the measurement of application-experienced
      latency.

   During the design of a protocol, the utility of features such as
   these should be considered.  The protocol's wire image can be
   designed to explicitly expose information to those network functions
   deemed important by the designers.  The wire image should expose as
   little other information as possible.

   However, even when information is explicitly provided to the network,
   any information that is exposed by the wire image, even that
   information not intended to be consumed by an observer, must be
   designed carefully, as deployed network functions using that
   information may render it immutable for future versions of the
   protocol.  For example, information needed to support decryption by
   the receiving endpoint (cryptographic handshakes, sequence numbers,
   and so on) may be used by devices along the path for their own
   purposes.

4.1.  Declaring Protocol Invariants

   One potential approach to reduce the extent of the wire image that
   will be used by devices on the path is to define a set of invariants
   for a protocol during its development.  Declaring a protocol's
   invariants represents a promise made by the protocol's developers
   that certain bits in the wire image, and behaviors observable in the
   wire image, will be preserved through the specification of all future
   versions of the protocol.  QUIC's invariants [QUIC-INVARIANTS] are an
   initial attempt to apply this approach to QUIC.

   While static aspects of the wire image - bits with simple semantics
   at fixed positions in protocol headers - can easily be made
   invariant, different aspects of the wire image may be more or less
   appropriate to define as invariants.  For a protocol with a version
   and/or extension negotiation mechanism, the bits in the header and
   behaviors tied to those bits which implement version negotiation



Trammell & Kuehlewind      Expires May 9, 2019                  [Page 6]


Internet-Draft                 Wire Image                  November 2018


   should be made invariant.  More fluid aspects of the wire image and
   behaviors which are not necessary for interoperability are not
   appropriate as invariants.

   Parts of a protocol's wire image not declared invariant but intended
   to be visible to devices on path should be protected against
   "accidental invariance": the deployment of on-path devices over time
   that make simplifying assumptions about the behavior of those parts
   of the wire image, making new behaviors not meeting those assumptions
   difficult to deploy.  Integrity protection of the wire image may
   itself help protect against accidental invariance, because read-only
   wire images invite less meddling than path-writable wire images.  The
   techniques discussed in [USE-IT] may also be useful in further
   preventing accidental invariance and ossification.

   Likewise, parts of a protocol's wire image not declared invariant and
   not intended to be visible to the path should be encrypted to protect
   their confidentiality.  When confidentiality protection is either not
   possible or not practical, then, as above, the approaches discussed
   in [USE-IT] may be useful in ossification prevention.

4.2.  Trustworthiness of Engineered Signals

   Since they are separate from the signals that drive an encrypted
   protocol's mechanisms, the accuracy of integrity-protected signals in
   an engineered wire image intended for consumption by the path may not
   be verifiable by on-path devices; see [PATH-SIGNALS].  Indeed, any
   two endpoints with a secret channel between them (in this case, the
   encrypted protocol itself) may collude to change the semantics and
   information content of these signals.  This is an unavoidable
   consequence of the separation of the wire image from the protocol's
   operation afforded by confidentiality protection of the protocol's
   headers.

5.  Acknowledgments

   Thanks to Martin Thomson, Stephen Farrell, Thomas Fossati, Ted
   Hardie, Mark Nottingham, Tommy Pauly, and the membership of the IAB
   Stack Evolution Program, for text, feedback, and discussions that
   have improved this document.

   This work is partially supported by the European Commission under
   Horizon 2020 grant agreement no. 688421 Measurement and Architecture
   for a Middleboxed Internet (MAMI), and by the Swiss State Secretariat
   for Education, Research, and Innovation under contract no. 15.0268.
   This support does not imply endorsement.





Trammell & Kuehlewind      Expires May 9, 2019                  [Page 7]


Internet-Draft                 Wire Image                  November 2018


6.  Informative References

   [PATH-SIGNALS]
              Hardie, T., "Path Signals", draft-hardie-path-signals-03
              (work in progress), April 2018.

   [QUIC]     Iyengar, J. and M. Thomson, "QUIC: A UDP-Based Multiplexed
              and Secure Transport", draft-ietf-quic-transport-16 (work
              in progress), October 2018.

   [QUIC-INVARIANTS]
              Thomson, M., "Version-Independent Properties of QUIC",
              draft-ietf-quic-invariants-03 (work in progress), October
              2018.

   [RFC0793]  Postel, J., "Transmission Control Protocol", STD 7,
              RFC 793, DOI 10.17487/RFC0793, September 1981,
              <https://www.rfc-editor.org/info/rfc793>.

   [RFC3168]  Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
              of Explicit Congestion Notification (ECN) to IP",
              RFC 3168, DOI 10.17487/RFC3168, September 2001,
              <https://www.rfc-editor.org/info/rfc3168>.

   [RFC7323]  Borman, D., Braden, B., Jacobson, V., and R.
              Scheffenegger, Ed., "TCP Extensions for High Performance",
              RFC 7323, DOI 10.17487/RFC7323, September 2014,
              <https://www.rfc-editor.org/info/rfc7323>.

   [RFC8226]  Peterson, J. and S. Turner, "Secure Telephone Identity
              Credentials: Certificates", RFC 8226,
              DOI 10.17487/RFC8226, February 2018,
              <https://www.rfc-editor.org/info/rfc8226>.

   [USE-IT]   Thomson, M., "Long-term Viability of Protocol Extension
              Mechanisms", draft-thomson-use-it-or-lose-it-02 (work in
              progress), June 2018.

Authors' Addresses

   Brian Trammell
   ETH Zurich
   Gloriastrasse 35
   8092 Zurich
   Switzerland

   Email: ietf@trammell.ch




Trammell & Kuehlewind      Expires May 9, 2019                  [Page 8]


Internet-Draft                 Wire Image                  November 2018


   Mirja Kuehlewind
   ETH Zurich
   Gloriastrasse 35
   8092 Zurich
   Switzerland

   Email: mirja.kuehlewind@tik.ee.ethz.ch












































Trammell & Kuehlewind      Expires May 9, 2019                  [Page 9]