6man Working Group A. Matsumoto
Internet-Draft T. Fujisaki
Intended status: Standards Track NTT
Expires: February 24, 2013 T. Chown
University of Southampton
August 23, 2012
Distributing Address Selection Policy using DHCPv6
draft-ietf-6man-addr-select-opt-05.txt
Abstract
RFC 3484 defines default address selection mechanisms for IPv6 that
allow nodes to select appropriate address when faced with multiple
source and/or destination addresses to choose between. The RFC 3484
allowed for the future definition of methods to administratively
configure the address selection policy information. This document
defines a new DHCPv6 option for such configuration, allowing a site
administrator to distribute address selection policy overriding the
default address selection parameters and policy table, and thus
control the address selection behavior of nodes in their site.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on February 24, 2013.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Matsumoto, et al. Expires February 24, 2013 [Page 1]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
1. Introduction
RFC 3484 [RFC3484] describes default algorithms for selecting an
address when a node has multiple destination and/or source addresses
to choose from by using an address selection policy. In Section 2 of
RFC 3484, it is suggested that the default policy table may be
administratively configured to suit the specific needs of a site.
This specification defines a new DHCPv6 option for such
configuration.
Some problems have been identified with the default RFC 3484 address
selection policy [RFC5220]. It is unlikely that any default policy
will suit all scenarios, and thus mechanisms to control the source
address selection policy will be necessary. Requirements for those
mechanisms are described in [RFC5221], while solutions are discussed
in [I-D.ietf-6man-addr-select-sol] and
[I-D.ietf-6man-addr-select-considerations]. Those documents have
helped shape the improvements in the default address selection
algorithm [I-D.ietf-6man-rfc3484bis] as well as the DHCPv6 option
defined in this specification.
1.1. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Matsumoto, et al. Expires February 24, 2013 [Page 2]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
1.2. Terminology
This document uses the terminology defined in [RFC2460] and the
DHCPv6 specification defined in [RFC3315]
2. Address Selection options
The Address Selection option provides the address selection policy
table, and some other configuration parameters.
A address selection option contains zero or more policy table
options. Multiple policy table options in a Policy Table option
constitute a single policy table.
The format of the Address Selection option is given below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_ADDRSEL | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |A|P| |
+-+-+-+-+-+-+-+-+ POLICY TABLE OPTIONS |
| (variable length) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Address Selection option format
option-code: OPTION_ADDRSEL (TBD).
option-len: The total length of the Reserved field, A, P flags, and
POLICY TABLE OPITONS in octets.
Reserved: Reserved field. Server MUST set this value to zero and
client MUST ignore its content.
A: Automatic Row Addition flag. This flag toggles the Automatic
Row Addition flag at client hosts, which is described in the
section 2.1 in RFC 3484 revision [I-D.ietf-6man-rfc3484bis]. If
this flag is set to 1, it does not change client host behavior,
that is, a client MAY automatically add additional site-specific
rows to the policy table. If set to 0, the Automatic Row
Addition flag is disabled, and a client MAY NOT automatically
add rows to the policy table.
Matsumoto, et al. Expires February 24, 2013 [Page 3]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
P: Privacy Preference flag. This flag toggles the Privacy
Preference flag at client hosts, which is described in the
section 5 in RFC 3484 revision [I-D.ietf-6man-rfc3484bis]. If
this flag is set to 1, it does not change client host behavior,
that is, a client SHOULD prefer temporary addresses. If set to
0, the Privacy Preference flag is disabled, and a client SHOULD
prefer public addresses.
POLICY TABLE OPTIONS: Zero or more Address Selection Policy Table
options described below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_ADDRSEL_TABLE | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| label | precedence | prefix-len | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| |
| prefix (variable length) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. Prefix Specific options .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Address Selection Policy Table option format
option-code: OPTION_ADDRSEL_TABLE (TBD).
option-len: The total length of the label field, precedence field,
prefix-len field, prefix field, and DASP options field in
octets.
label: An 8-bit unsigned integer; this value is used to make a
combination of source address prefixes and destination address
prefixes.
precedence: An 8-bit unsigned integer; this value is used for
sorting destination addresses.
Matsumoto, et al. Expires February 24, 2013 [Page 4]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
prefix-len: An 8-bit unsigned integer; the number of leading bits in
the prefix that are valid. The value ranges from 0 to 128.
prefix: A variable-length field containing an IP address or the
prefix of an IP address. An IPv4-mapped address [RFC4291] must
be used to represent an IPv4 address as a prefix value. The
Prefix should be truncated on the byte boundary. So the length
of this field should be between 0 and 16 bytes.
Prefix Specific options: Options specific to this particular Address
Selection Policy option. This includes, but not limited to,
zero or one Zone Index option that specify the zone index of the
prefix in this option.
The format of the Zone Index option is given below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_ADDRSEL_ZONE | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| zone-index |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Zone Index option format
option-code: OPTION_ADDRSEL_ZONE (TBD).
option-len: 4.
zone-index: The zone-index field is an 32-bit unsigned integer, and
used to specify the zone for scoped addresses. The zone-index
is defined in RFC 3493 [RFC3493] as 'scope ID'.
3. Appearance of the Address Selection options
The Address Selection options MUST NOT appear in any messages other
than the following ones: Solicit, Advertise, Request, Renew, Rebind,
Reconfigure, Information-Request, and Reply.
4. Processing the Policy Table option
This section describes how to process received Policy Table option at
Matsumoto, et al. Expires February 24, 2013 [Page 5]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
the DHCPv6 client.
This option's concept is to serve as a hint for a node about how to
behave in the network. So, basically, it should be up to the node's
administrator how to deal with the received policy information in the
way described below.
4.1. Handling of the local policy table
RFC 3484 defines the default policy table. Also, a user is usually
able to configure the policy table to satisfy his requirement.
The client implementation SHOULD provide the following choices to the
user:
a) It receives distributed policy table, and replaces the existing
policy tables with that.
b) It preserves the default policy table, or manually configured
policy.
4.2. Handling of the stale policy table
When the information from the DHCP server goes stale, the policy
received form the DHCP server should be removed and the default
policy should be restored.
The received information can be considered stale in several cases,
such as, when the interface goes down, the DHCP server does not
respond for a certain amount of time, and the Information Refresh
Time is expired.
4.3. Multi-interface situation
The policy table, and other parameters specified in this document are
node-global information by its nature. So, the node cannot use
multiple received policies at the same time. In other words, once
the received policy from one source is merged with one from another
source, the effect of both policy are more or less changed. The
policy table is defined as a whole, so the slightest addition/
deletion from the policy table brings a change in semantics of the
policy.
It also should be noted that absence of the distributed policy from a
certain network interface should not be treated as absence of policy
itself, because it may mean preference for the default address
selection policy.
Under the above assumptions, how to handle received policy is
Matsumoto, et al. Expires February 24, 2013 [Page 6]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
specified below.
A node MAY use Address Selection options by default in any of the
following two cases:
1: The host is single-homed, where the host belongs to one
administrative network domain exclusively usually through one
active network interface.
2: The host implements some advanced heuristics to deal with multiple
received policy, which is outside the scope of this document.
The above restrictions do not preclude implementations from providing
configuration options to enable this option on a certain network
interface.
5. Implementation Considerations
o The value 'label' is passed as an unsigned integer, but there is
no special meaning for the value, that is whether it is a large or
small number. It is used to select a preferred source address
prefix corresponding to a destination address prefix by matching
the same label value within the DHCP message. DHCPv6 clients need
to convert this label to a representation specified by each
implementation (e.g., string).
o Currently, the label and precedence values are defined as 8-bit
unsigned integers. In almost all cases, this value will be
enough.
o The maximum number of address selection rules that may be conveyed
in one DHCPv6 message depends on the prefix length of each rule
and the maximum DHCPv6 message size defined in RFC 3315. It is
possible to carry over 3,000 rules in one DHCPv6 message (maximum
UDP message size). However, it should not be expected that DHCP
clients, servers and relay agents can handle UDP fragmentation.
So, the number of the options and the total size of the options
should be taken care of.
o Since the number of selection rules could be large, an
administrator configuring the policy to be distributed should
consider the resulting DHCPv6 message size.
6. Security Considerations
A rogue DHCPv6 server could issue bogus address selection policies to
Matsumoto, et al. Expires February 24, 2013 [Page 7]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
a client. This might lead to incorrect address selection by the
client, and the affected packets might be blocked at an outgoing ISP
because of ingress filtering. Alternatively, an IPv6 transition
mechanism might be preferred over native IPv6, even if it is
available. To guard against such attacks, a legitimate DHCPv6 server
should be communicated through a secure, trusted channel, such as a
channel protected by IPsec, SEND and DHCP authentication, as
described in section 21 of RFC 3315,
Another threat is about privacy concern. As in the security
consideration section of RFC 3484, at least a part of, the address
selection policy stored in a host can be leaked by a packet from a
remote host. This issue will not be degraded regardless of the
introduction of this option, or regardless of whether the host is
multihomed or not.
7. IANA Considerations
IANA is requested to assign option codes to OPTION_ADDRSEL ,
OPTION_ADDRSEL_TABLE, and OPTION_ADDRSEL_ZONE from the option-code
space as defined in section "DHCPv6 Options" of RFC 3315.
8. References
8.1. Normative References
[I-D.ietf-6man-rfc3484bis]
Thaler, D., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol version 6
(IPv6)", draft-ietf-6man-rfc3484bis-06 (work in progress),
June 2012.
[I-D.ietf-6man-stable-privacy-addresses]
Gont, F., "A method for Generating Stable Privacy-Enhanced
Addresses with IPv6 Stateless Address Autoconfiguration
(SLAAC)", draft-ietf-6man-stable-privacy-addresses-00
(work in progress), May 2012.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3484] Draves, R., "Default Address Selection for Internet
Matsumoto, et al. Expires February 24, 2013 [Page 8]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
Protocol version 6 (IPv6)", RFC 3484, February 2003.
8.2. Informative References
[I-D.ietf-6man-addr-select-considerations]
Chown, T. and A. Matsumoto, "Considerations for IPv6
Address Selection Policy Changes",
draft-ietf-6man-addr-select-considerations-04 (work in
progress), October 2011.
[I-D.ietf-6man-addr-select-sol]
Matsumoto, A., Fujisaki, T., and R. Hiromi, "Solution
approaches for address-selection problems",
draft-ietf-6man-addr-select-sol-03 (work in progress),
March 2010.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC3493] Gilligan, R., Thomson, S., Bound, J., McCann, J., and W.
Stevens, "Basic Socket Interface Extensions for IPv6",
RFC 3493, February 2003.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy
Extensions for Stateless Address Autoconfiguration in
IPv6", RFC 4941, September 2007.
[RFC5220] Matsumoto, A., Fujisaki, T., Hiromi, R., and K. Kanayama,
"Problem Statement for Default Address Selection in Multi-
Prefix Environments: Operational Issues of RFC 3484
Default Rules", RFC 5220, July 2008.
[RFC5221] Matsumoto, A., Fujisaki, T., Hiromi, R., and K. Kanayama,
"Requirements for Address Selection Mechanisms", RFC 5221,
July 2008.
Appendix A. Past Discussion
o The 'zone index' value is used to specify a particular zone for
scoped addresses. This can be used effectively to control address
selection in the site scope (e.g., to tell a node to use a
specified source address corresponding to a site-scoped multicast
address). However, in some cases such as a link-local scope
address, the value specifying one zone is only meaningful locally
Matsumoto, et al. Expires February 24, 2013 [Page 9]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
within that node. There might be some cases where the
administrator knows which clients are on the network and wants
specific interfaces to be used though. However, in general case,
it is hard to use this value.
o Since we got a comment that some implementations use 32-bit
integers for zone index value, we extended the bit length of the
'zone index' field. However, as described above, there might be
few cases to specify 'zone index' in policy distribution, we
defined this field as optional, controlled by a flag.
o There may be some demands to control the use of special address
types such as the temporary addresses described in RFC4941
[RFC4941], address assigned by DHCPv6 and so on. (e.g., informing
not to use a temporary address when it communicate within the an
organization's network). It is possible to indicate the type of
addresses using reserved field value.
Authors' Addresses
Arifumi Matsumoto
NTT NT Lab
3-9-11 Midori-Cho
Musashino-shi, Tokyo 180-8585
Japan
Phone: +81 422 59 3334
Email: arifumi@nttv6.net
Tomohiro Fujisaki
NTT NT Lab
3-9-11 Midori-Cho
Musashino-shi, Tokyo 180-8585
Japan
Phone: +81 422 59 7351
Email: fujisaki@nttv6.net
Matsumoto, et al. Expires February 24, 2013 [Page 10]
Internet-Draft DHCPv6 Address Selection Policy Opt August 2012
Tim Chown
University of Southampton
Southampton, Hampshire SO17 1BJ
United Kingdom
Email: tjc@ecs.soton.ac.uk
Matsumoto, et al. Expires February 24, 2013 [Page 11]