6man Z. Ali
Internet-Draft C. Filsfils
Intended status: Standards Track Cisco Systems
Expires: October 1, 2020 S. Matsushima
Softbank
D. Voyer
Bell Canada
M. Chen
Huawei
March 30, 2020
Operations, Administration, and Maintenance (OAM) in Segment Routing
Networks with IPv6 Data plane (SRv6)
draft-ietf-6man-spring-srv6-oam-04
Abstract
This document defines building blocks for Operations, Administration,
and Maintenance (OAM) in Segment Routing Networks with IPv6 Dataplane
(SRv6). The document also describes some SRv6 OAM mechanisms.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 1, 2020.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Ali, et al. Expires October 1, 2020 [Page 1]
Internet-Draft SRv6 OAM March 2020
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 3
3. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Terminology and Reference Topology . . . . . . . . . . . . . 3
5. OAM Mechanisms . . . . . . . . . . . . . . . . . . . . . . . 5
5.1. O-flag in Segment Routing Header . . . . . . . . . . . . 5
5.1.1. O-flag Processing . . . . . . . . . . . . . . . . . . 5
5.2. OAM Segments . . . . . . . . . . . . . . . . . . . . . . 6
5.3. End.OP: OAM Endpoint with Punt . . . . . . . . . . . . . 6
6. Illustrations . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1. Ping in SRv6 Networks . . . . . . . . . . . . . . . . . . 7
6.1.1. Classic Ping . . . . . . . . . . . . . . . . . . . . 7
6.1.2. Pinging a SID . . . . . . . . . . . . . . . . . . . . 9
6.2. Traceroute . . . . . . . . . . . . . . . . . . . . . . . 9
6.2.1. Classic Traceroute . . . . . . . . . . . . . . . . . 10
6.2.2. Traceroute to a SID . . . . . . . . . . . . . . . . . 11
6.3. A Controller-Based Passive OAM Using O-flag . . . . . . . 13
6.4. Monitoring of SRv6 Paths . . . . . . . . . . . . . . . . 15
7. Implementation Status . . . . . . . . . . . . . . . . . . . . 16
8. Security Considerations . . . . . . . . . . . . . . . . . . . 16
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16
9.1. ICMPv6 type Numbers Registry . . . . . . . . . . . . . . 16
9.2. SRv6 OAM Endpoint Types . . . . . . . . . . . . . . . . . 17
9.3. Segment Routing Header Flags . . . . . . . . . . . . . . 17
10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 17
11. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 17
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 18
12.1. Normative References . . . . . . . . . . . . . . . . . . 18
12.2. Informative References . . . . . . . . . . . . . . . . . 19
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 20
1. Introduction
This document defines building blocks for Operations, Administration,
and Maintenance (OAM) in Segment Routing Networks with IPv6 Dataplane
(SRv6).
Ali, et al. Expires October 1, 2020 [Page 2]
Internet-Draft SRv6 OAM March 2020
2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119], [RFC8174].
3. Abbreviations
The following abbreviations are used in this document:
SID: Segment ID.
SL: Segments Left.
SR: Segment Routing.
SRH: Segment Routing Header.
SRv6: Segment Routing with IPv6 Data plane.
TC: Traffic Class.
ICMPv6: ICMPv6 Specification [RFC4443].
4. Terminology and Reference Topology
This document uses the terminology defined in [I-D.ietf- spring-srv6-
network-programming]. The readers are expected to be familiar with
the same.
Throughout the document, the following simple topology is used for
illustration.
+--------------------------| N100 |---------------------------------+
| |
| ====== link1====== link3------ link5====== link9------ ====== |
||N1||------||N2||------| N3 |------||N4||------| N5 |---||N7||
|| ||------|| ||------| |------|| ||------| |---|| ||
====== link2====== link4------ link6======link10------ ======
| | | |
---+-- | ------ | --+---
|CE 1| +-------| N6 |---------+ |CE 2|
------ link7 | | link8 ------
------
Figure 1 Reference Topology
Ali, et al. Expires October 1, 2020 [Page 3]
Internet-Draft SRv6 OAM March 2020
In the reference topology:
Node k has a classic IPv6 loopback address A:k::/128.
Nodes N1, N2, and N4 are SRv6 capable nodes.
Nodes N3, N5 and N6 are IPv6 nodes that are not SRv6 capable.
Such nodes are referred as classic IPv6 nodes.
A SID at node k with locator block B and function F is represented
by B:k:F::.
Node N100 is a controller.
The IPv6 address of the nth Link between node X and Y at the X
side is represented as 2001:DB8:X:Y:Xn::, e.g., the IPv6 address
of link6 (the 2nd link) between N3 and N4 at N3 in Figure 1 is
2001:DB8:3:4:32::. Similarly, the IPv6 address of link5 (the 1st
link between N3 and N4) at node 3 is 2001:DB8:3:4:31::.
B:k:Cij:: is explicitly allocated as the END.X function at node k
towards neighbor node i via jth Link between node i and node k.
e.g., B:2:C31:: represents END.X at N2 towards N3 via link3 (the
1st link between N2 and N3). Similarly, B:4:C52:: represents the
END.X at N4 towards N5 via link10.
A SID list is represented as <S1, S2, S3> where S1 is the first
SID to visit, S2 is the second SID to visit and S3 is the last SID
to visit along the SR path.
(SA,DA) (S3, S2, S1; SL)(payload) represents an IPv6 packet with:
* IPv6 header with source address SA, destination addresses DA
and SRH as next-header
* SRH with SID list <S1, S2, S3> with SegmentsLeft = SL
* Note the difference between the < > and () symbols: <S1, S2,
S3> represents a SID list where S1 is the first SID and S3 is
the last SID to traverse. (S3, S2, S1; SL) represents the same
SID list but encoded in the SRH format where the rightmost SID
in the SRH is the first SID and the leftmost SID in the SRH is
the last SID. When referring to an SR policy in a high-level
use-case, it is simpler to use the <S1, S2, S3> notation. When
referring to an illustration of the detailed packet behavior,
the (S3, S2, S1; SL) notation is more convenient.
* (payload) represents the the payload of the packet.
Ali, et al. Expires October 1, 2020 [Page 4]
Internet-Draft SRv6 OAM March 2020
SRH[SL] represents the SID pointed by the SL field in the first
SRH. In our example SID list (S3, S2, S1; SL), SRH[2] represents
S1, SRH[1] represents S2 and SRH[0] represents S3.
5. OAM Mechanisms
As Segment Routing with IPv6 data plane (SRv6) simply adds a new type
of Routing Extension Header, existing IPv6 OAM mechanisms can be used
in an SRv6 network.
This section defines OAM enhancement for the SRv6 networks.
Specifically, it defines the O-flag for implementing a controller
based passive OAM mechanism and an OAM SID to more closely examine
the contents of packet at a segment endpoint for active OAM.
5.1. O-flag in Segment Routing Header
[] describes the Segment Routing
Header (SRH) and how SR capable nodes use it. The SRH contains an
8-bit "Flags" field. This document defines the following bit in the
SRH.Flags to carry the O-flag:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
| |O| |
+-+-+-+-+-+-+-+-+
Where:
O-flag: OAM flag. When set, it indicates that this packet is an
Operation Administration and Maintenance (OAM) packet. This
document defines the usage of the O-flag in the SRH.Flags.
The document does not define any other flag in the SRH.Flags and
meaning and processing of any other bit in SRH.Flags is outside of
the scope of this document.
5.1.1. O-flag Processing
The SRH.Flags.O-flag implements the "punt a timestamped copy of the
packet" behavior. This enables an SRv6 Endpoint node to send a
timestamped copy of the packets marked with o-flag to a local OAM
process. To prevent multiple evaluations of the datagram, the OAM
process MUST NOT process the packet or respond to any upper-layer
header (like ICMP, UDP, etc.) payload. However, the OAM process MAY
export the time-stamped copy of the packet to a controller using
e.g., IPFIX [RFC7011]. If data from the last node in the segment-
Ali, et al. Expires October 1, 2020 [Page 5]
Internet-Draft SRv6 OAM March 2020
list (Egress node) is desired, the ingress uses an Ultimate Segment
Pop (USP) SID advertised by the Egress node. To avoid hitting any
performance impact, the processing node SHOULD rate-limit the number
of packets punted to the OAM process. Specification of the OAM
process or the external controller operations are beyond the scope of
this document. Section 6 illustrates use of the SRH.Flags.O-flag for
implementing a controller-based passive OAM mechanism.
Implementation of the O-flag is OPTIONAL. If a node does not support
the O-flag, then upon reception it simply ignores it.
If a node supports the O-flag, it can optionally advertise its
potential via node capability advertisement in IGP [I-D.ietf-isis-
srv6- extensions] and BGP-LS [I-D.ietf-idr-bgpls-srv6-ext].
When N receives a packet whose IPv6 DA is S and S is a local SID, the
line S01 of the pseudo-code associated with the SID S, as defined in
section 4.3.1.1 of [I-D.ietf-6man-segment-routing-header], is
modified as follows for the O-flag processing.
S01.1. IF SRH.Flags.O-flag is set and local configuration permits
O-flag processing THEN
a. Make a copy of the packet.
b. Send the copied packet, along with a timestamp
to the OAM process. ;; Ref1
Ref1: An implementation SHOULD copy and record the timestamp as
soon as possible during packet processing. Timestamp is not
carried in the packet forwarded to the next hop.
Please note that the O-flag processing happens before execution of
regular processing of the local SID S.
5.2. OAM Segments
The presence of an OAM SID in the Destination address of the IPv6
header instructs the segment endpoint implementing the OAM SID that
the content of the packet is of interest.
The document defines OAM Endpoint with Punt action. Additional OAM
SIDs may be defined in future documents.
5.3. End.OP: OAM Endpoint with Punt
When N receives a packet destined to S and S is a local End.OP SID, N
does:
Ali, et al. Expires October 1, 2020 [Page 6]
Internet-Draft SRv6 OAM March 2020
S01. Send the packet to the OAM process
The local OAM process further processes the packet, this MAY involve
processing protocol layers above IPv6. For example, ping and
traceroute will require ICMP or UDP protocol processing. Once the
packet leaves the IPv6 layer the processing is considered host
processing and the upper layer protocols MUST be processed as such.
As END.OP SID terminates the forwarding of the probe packets for the
upper layer processing, it is used for the active OAM mechanisms.
For example, the END.OP SID SID is not designed for implementing In-
situ OAM mechanisms defined in [I.D-draft-ietf-ippm-ioam-data].
6. Illustrations
This section illustrates the use of existing IPv6 OAM mechanisms in
the SRv6 network. It also illustrates the use of the END.OP SID and
O-flag at segment endpoints.
The document does not propose any changes to the standard ICMPv6
[RFC4443], [RFC4884] or standard ICMPv4 [RFC792] or [RFC2151].
6.1. Ping in SRv6 Networks
The following subsections outline some use cases of the ICMP ping in
the SRv6 networks.
6.1.1. Classic Ping
The existing mechanism to query liveliness of a remote IP address,
along the shortest path, continues to work without any modification.
The initiator may be an SRv6 node or a classic IPv6 node. Similarly,
the egress or transit may be an SRv6 capable node or a classic IPv6
node.
If an SRv6 capable ingress node wants to ping an IPv6 prefix via an
arbitrary segment list <S1, S2, S3>, it needs to initiate ICMPv6 ping
with an SR header containing the SID list <S1, S2, S3>. This is
illustrated using the topology in Figure 1. Assume all the links
have IGP metric 10 except both links between node2 and node3, which
have IGP metric set to 100. User issues a ping from node N1 to a
loopback of node 5, via segment list <B:2:C31, B:4:C52>.
Figure 2 contains sample output for a ping request initiated at node
N1 to the loopback address of node N5 via a segment list <B:2:C31,
B:4:C52>.
Ali, et al. Expires October 1, 2020 [Page 7]
Internet-Draft SRv6 OAM March 2020
> ping A:5:: via segment-list B:2:C31, B:4:C52
Sending 5, 100-byte ICMP Echos to B5::, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0.625
/0.749/0.931 ms
Figure 2 A sample ping output at an SRv6 capable node
All transit nodes process the echo request message like any other
data packet carrying SR header and hence do not require any change.
Similarly, the egress node (IPv6 classic or SRv6 capable) does not
require any change to process the ICMPv6 echo request. Furthermore,
there is no difference in processing of the ICMPv6 echo request at an
IPv6 classic node or an SRv6 capable node. For example, in the ping
example of Figure 2:
o Node N1 initiates an ICMPv6 ping packet with SRH as follows
(A:1::, B:2:C31)(A:5::, B:4:C52, B:2:C31, SL=2, NH =
ICMPv6)(ICMPv6 Echo Request). If B:4:C52 is a PSP SID, the OAM
probes encodes the PSP SID in the packet (just mimicking data
packets). No special consideration is needed to handle PSP SIDs.
o Node N2, which is an SRv6 capable node, performs the standard SRH
processing. Specifically, it executes the END.X function
(B:2:C31) and forwards the packet on link3 to N3.
o Node N3, which is a classic IPv6 node, performs the standard IPv6
processing. Specifically, it forwards the echo request based on
the DA B:4:C52 in the IPv6 header.
o Node N4, which is an SRv6 capable node, performs the standard SRH
processing. Specifically, it observes the END.X function
(B:4:C52) and forwards the packet on link10 towards N5. If
B:4:C52 is a PSP SID, The penultimate node (Node N4) does not,
should no and cannot differentiate between the data packets and
OAM probes. Specifically, if B:4:C52 is a PSP SID, node N4
executes the SID like any other data packet with DA = B:4:C52 and
removes the SRH.
o The echo request packet at N5 arrives as an IPv6 packet with or
without an SRH. If N5 receives the packet with SRH, it skips SRH
processing. In either case, Node N5 performs the standard IPv6/
ICMPv6 processing on the echo request.
Ali, et al. Expires October 1, 2020 [Page 8]
Internet-Draft SRv6 OAM March 2020
6.1.2. Pinging a SID
The following illustration uses END.OP SID for pinging a SID.
Consider the example where the user wants to ping a remote SID
function B:4:C52, via B:2:C31, from node N1. The ICMPv6 echo request
is processed at the individual nodes along the path as follows:
o To force a punt of the ICMPv6 echo request at the node N4, node N1
inserts the END.OP SID just before the target SID B:4:C52 in the
SRH. Specifically, Node N1 initiates an ICMPv6 ping packet with
SRH as follows (A:1::, B:2:C31)(B:4:C52, B:4:OP, B:2:C31; SL=2;
NH=ICMPv6)(ICMPv6 Echo Request).
o Node N2, which is an SRv6 capable node, performs the standard SRH
processing. Specifically, it executes the END.X function
(B:2:C31) on the echo request packet.
o Node N3 receives the packet as follows (A:1::, B:4:OP)(B:4:C52,
B:4:OP, B:2:C31 ; SL=1; NH=ICMPv6)(ICMPv6 Echo Request). Node N3,
which is a classic IPv6 node, performs the standard IPv6
processing. Specifically, it forwards the echo request based on
DA B:4:OP in the IPv6 header.
o When node N4 receives the packet (A:1::, B:4:OP)(B:4:C52, B:4:OP,
B:2:C31 ; SL=1; NH=ICMPv6)(ICMPv6 Echo Request), it processes the
END.OP SID, as described in the pseudocode in Section 3. The
packet gets punted to the OAM process for processing. The OAM
process checks if the next SID in SRH (the target SID B:4:C52) is
locally programmed.
o If the next SID is not locally programmed, the OAM process returns
an ICMPv6 error message type 4 (parameter problem) code 0
(erroneous header field encountered) with pointer set to the
target SID B:4:C52 and the packet is discarded.
o If the next SID is locally programmed, the node processes the
upper layer header, as a host. As part of the upper layer header
(ICMPv6) processing node N4 sends the ICMPv6 Echo Reply message
[RFC4443].
6.2. Traceroute
There is no hardware or software change required for traceroute
operation at the classic IPv6 nodes in an SRv6 network. That
includes the classic IPv6 node with ingress, egress or transit roles.
Furthermore, no protocol changes are required to the standard
Ali, et al. Expires October 1, 2020 [Page 9]
Internet-Draft SRv6 OAM March 2020
traceroute operations. In other words, existing traceroute
mechanisms work seamlessly in the SRv6 networks.
The following subsections outline some use cases of the traceroute in
the SRv6 networks.
6.2.1. Classic Traceroute
The existing mechanism to traceroute a remote IP prefix, along the
shortest path, continues to work without any modification. The
initiator may be an SRv6 node or a classic IPv6 node. Similarly, the
egress or transit may be an SRv6 node or a classic IPv6 node.
If an SRv6 capable ingress node wants to traceroute to IPv6 prefix
via an arbitrary segment list <S1, S2, S3>, it needs to initiate
traceroute probe with an SR header containing the SID list <S1, S2,
S3>. That is illustrated using the topology in Figure 1. Assume all
the links have IGP metric 10 except both links between node2 and
node3, which have IGP metric set to 100. User issues a traceroute
from node N1 to a loopback of node 5, via segment list <B:2:C31,
B:4:C52>. Figure 3 contains sample output for the traceroute
request.
> traceroute A:5:: via segment-list B:2:C31, B:4:C52
Tracing the route to A:5::
1 2001:DB8:1:2:21:: 0.512 msec 0.425 msec 0.374 msec
SRH: (A:5::, B:4:C52, B:2:C31, SL=2)
2 2001:DB8:2:3:31:: 0.721 msec 0.810 msec 0.795 msec
SRH: (A:5::, B:4:C52, B:2:C31, SL=1)
3 2001:DB8:3:4:41:: 0.921 msec 0.816 msec 0.759 msec
SRH: (A:5::, B:4:C52, B:2:C31, SL=1)
4 2001:DB8:4:5:52:: 0.879 msec 0.916 msec 1.024 msec
Figure 3 A sample traceroute output at an SRv6 capable node
Please note that if B:4:C52 is a PSP SID, the traceroute probe
encodes the PSP SID in the packet (just mimicking data packets).
Likewise, if B:4:C52 is a PSP SID, node N4 executes the SID like any
other data packet with DA = B:4:C52. I.e., no special consideration
is needed to handle PSP SIDs.
Please note that information for hop2 is returned by N3, which is a
classic IPv6 node. Nonetheless, the ingress node is able to display
SR header contents as the packet travels through the IPv6 classic
node. This is because the "Time Exceeded Message" ICMPv6 message can
contain as much of the invoking packet as possible without the ICMPv6
packet exceeding the minimum IPv6 MTU [RFC4443]. The SR header is
Ali, et al. Expires October 1, 2020 [Page 10]
Internet-Draft SRv6 OAM March 2020
also included in these ICMPv6 messages initiated by the classic IPv6
transit nodes that are not running SRv6 software. Specifically, a
node generating ICMPv6 message containing a copy of the invoking
packet does not need to understand the extension header(s) in the
invoking packet.
The segment list information returned for hop1 is returned by N2,
which is an SRv6 capable node. Just like for hop2, the ingress node
is able to display SR header contents for hop1.
There is no difference in processing of the traceroute probe at an
IPv6 classic node and an SRv6 capable node. Similarly, both IPv6
classic and SRv6 capable nodes may use the address of the interface
on which probe was received as the source address in the ICMPv6
response. ICMP extensions defined in [RFC5837] can be used to also
display information about the IP interface through which the datagram
would have been forwarded had it been forwardable, and the IP next
hop to which the datagram would have been forwarded, the IP interface
upon which a datagram arrived, the sub-IP component of an IP
interface upon which a datagram arrived.
The information about the IP address of the incoming interface on
which the traceroute probe was received by the reporting node is very
useful. This information can also be used to verify if SID functions
B:2:C31 and B:4:C52 are executed correctly by N2 and N4,
respectively. Specifically, the information displayed for hop2
contains the incoming interface address 2001:DB8:2:3:31:: at N3.
This matches with the expected interface bound to END.X function
B:2:C31 (link3). Similarly, the information displayed for hop5
contains the incoming interface address 2001:DB8:4:5:52:: at N5.
This matches with the expected interface bound to the END.X function
B:4:C52 (link10).
6.2.2. Traceroute to a SID
The following illustration uses END.OP SID for trace-routing a SID.
The illustration assumes traceroute probe is UDP encoded but the
procedure is equally applicable to other encoding types.
Consider the example where the user wants to traceroute to a remote
SID function B:4:C52, via B:2:C31, from node N1. The traceroute
probe is processed at the individual nodes along the path as follows:
o To force a punt of the traceroute probe at the node N4, node N1
inserts the END.OP SID just before the target SID B:4:C52 in the
SRH. Specifically, Node N1 initiates a traceroute probe packet
with a monotonically increasing value of hop-count and SRH as
Ali, et al. Expires October 1, 2020 [Page 11]
Internet-Draft SRv6 OAM March 2020
follows (A:1::, B:2:C31)(B:4:C52, B:4:OP, B:2:C31; SL=2;
NH=UDP)(Traceroute probe).
o When node N2 receives the packet with hop-count = 1, it processes
the hop-limit expiry. Specifically, the node N2 responses with
the ICMPv6 message (Type: "Time Exceeded", Code: "Time to Live
exceeded in Transit").
o When Node N2 receives the packet with hop-count > 1, it performs
the standard SRv6 SID and SRH processing. Specifically, it
executes the END.X function (B:2:C31) on the traceroute probe.
o When node N3, which is a classic IPv6 node, receives the packet
(A:1::, B:4:OP)(B:4:C52, B:4:OP, B:2:C31 ; HC=1, SL=1;
NH=UDP)(Traceroute probe) with hop-count = 1, it processes the
hop-limit expiry. Specifically, the node N3 responses with the
ICMPv6 message (Type: "Time Exceeded", Code: "Time to Live
exceeded in Transit").
o When node N3, which is a classic IPv6 node, receives the packet
with hop-count > 1, it performs the standard IPv6 processing.
Specifically, it forwards the traceroute probe based on DA B:4:OP
in the IPv6 header.
o When node N4 receives the packet (A:1::, B:4:OP)(B:4:C52, B:4:OP,
B:2:C31 ; SL=1; HC=1, NH=UDP)(Traceroute probe), it processes the
END.OP SID, as described in the pseudocode in Section 3, before
hop-limit processing. The packet gets punted to the OAM process
for processing. The OAM process checks if the next SID in SRH
(the target SID B:4:C52) is locally programmed.
o If the next SID is not locally programmed, the OAM process returns
an ICMPv6 error message type 4 (parameter problem) code 0
(erroneous header field encountered) with pointer set to the
target SID B:4:C52 and the packet is discarded.
o If the next SID is locally programmed, the node processes the
upper layer header. As part of the upper layer header processing
node N4 responses with the ICMPv6 message (Type: Destination
unreachable, Code: Port Unreachable).
Figure 4 displays a sample traceroute output for this example.
Ali, et al. Expires October 1, 2020 [Page 12]
Internet-Draft SRv6 OAM March 2020
> traceroute srv6 B:4:C52 via segment-list B:2:C31
Tracing the route to SID function B:4:C52
1 2001:DB8:1:2:21:: 0.512 msec 0.425 msec 0.374 msec
SRH: (B:4:C52, B:4:OP, B:2:C31; SL=2)
2 2001:DB8:2:3:31:: 0.721 msec 0.810 msec 0.795 msec
SRH: (B:4:C52, B:4:OP, B:2:C31; SL=1)
3 2001:DB8:3:4:41:: 0.921 msec 0.816 msec 0.759 msec
SRH: (B:4:C52, B:4:OP, B:2:C31; SL=1)
Figure 4 A sample output for traceroute to a SID
6.3. A Controller-Based Passive OAM Using O-flag
This section illustrates a controller-based passive OAM mechanism
using the SRH.Flags.O-flag.
The mechanism is different than the passive In-situ OAM defined in
[I.D-draft-ietf-ippm-ioam-data]. This is because In-situ OAM records
operational and telemetry information in the packet as the packet
traverses a path between two points in the network [I.D-draft-ietf-
ippm-ioam-data]. The controller-based OAM mechanism using O-flag
described in this section does not require the recording of OAM data
in the packet. Instead, a copy of the packet with the SRH.O-flag set
is sent to a local OAM process. The OAM process adds the required
metadata to the packet and sends the packet to a controller for
further processing. Specification of how the OAM process computes
the metadata and how the controller correlates and processes the copy
of the packets from different segment endpoints is beyond the scope
of this document.
Consider the example where the user wants to monitor sampled IPv4 VPN
100 traffic going from CE1 to CE2 via a low latency SR policy P
installed at Node N1. To exercise a low latency path, the SR Policy
P forces the packet via segments B:2:C31 and B:4:C52. The VPN SID at
N7 associated with VPN100 is B:7:DT100. B:7:DT100 is a USP SID. N1,
N4, and N7 are capable of processing SRH.Flags.O-flag but N2 is not
capable of processing SRH.Flags.O-flag. N100 is the centralized
controller capable of processing and correlating the copy of the
packets sent from nodes N1, N4, and N7. N100 is aware of
SRH.Flags.O-flag processing capabilities. Controller N100 with the
help from nodes N1, N4, N7 and implements a passive OAM mechanism
using the SRH.Flags.O-flag as follows:
o A packet P1:(IPv4 header)(payload) is sent from CE1 to Node N1.
o Node N1 steers the packet P1 through the Policy P. Based on a
local configuration, Node N1 also implements logic to sample
traffic steered through policy P for passive OAM purposes.
Ali, et al. Expires October 1, 2020 [Page 13]
Internet-Draft SRv6 OAM March 2020
Specification for the sampling logic is beyond the scope of this
document. Consider the case where packet P1 is classified as a
packet to be monitored via the passive OAM. Node N1 sets
SRH.Flags.O-flag during encapsulation required by policy P. As
part of setting the SRH.Flags.O-flag, node N1 also send a
timestamped copy of the packet P1: (A:1::, B:2:C31)(B:7:DT100,
B:4:C52, B:2:C31; SL=2; O-flag=1; NH=IPv4)(IPv4 header)(payload)
to a local OAM process. The local OAM process sends a full or
partial copy of the packet P1 to the controller N100. The OAM
process includes the recorded timestamp, additional OAM
information like incoming and outgoing interface, etc. along with
any applicable metadata. Node N1 forwards the original packet
towards the next segment B:2:C31.
o When node N2 receives the packet with SRH.Flags.O-flag set, it
ignores the SRH.Flags.O-flag. This is because node N2 is not
capable of processing the O-flag. Node N2 performs the standard
SRv6 SID and SRH processing. Specifically, it executes the END.X
function (B:2:C31) and forwards the packet P1 (A:1::,
B:4:C52)(B:7:DT100, B:4:C52, B:2:C31; SL=1; O-flag=1;
NH=IPv4)(IPv4 header)(payload) over link 3 towards Node N3.
o When node N3, which is a classic IPv6 node, receives the packet P1
, it performs the standard IPv6 processing. Specifically, it
forwards the packet P1 based on DA B:4:C52 in the IPv6 header.
o When node N4 receives the packet P1 (A:1::, B:4:C52)(B:7:DT100,
B:4:C52, B:2:C31; SL=1; O-flag=1; NH=IPv4)(IPv4 header)(payload),
it processes the SRH.Flags.O-flag. As part of processing the
O-flag, it sends a timestamped copy of the packet to a local OAM
process. The local OAM process sends a full or partial copy of
the packet P1 to the controller N100. The OAM process includes
the recorded timestamp, additional OAM information like incoming
and outgoing interface, etc. along with any applicable metadata.
Node N4 performs the standard SRv6 SID and SRH processing on the
original packet P1. Specifically, it executes the END.X function
(B:4:C52) and forwards the packet P1 (A:1::, B:7:DT100)(B:7:DT100,
B:4:C52, B:2:C31; SL=0; O-flag=1; NH=IPv4)(IPv4 header)(payload)
over link 10 towards Node N5.
o When node N5, which is a classic IPv6 node, receives the packet
P1, it performs the standard IPv6 processing. Specifically, it
forwards the packet based on DA B:7:DT100 in the IPv6 header.
o When node N7 receives the packet P1 (A:1::, B:7:DT100)(B:7:DT100,
B:4:C52, B:2:C31; SL=0; O-flag=1; NH=IPv4)(IPv4 header)(payload),
it processes the SRH.Flags.O-flag. As part of processing the
O-flag, it sends a timestamped copy of the packet to a local OAM
Ali, et al. Expires October 1, 2020 [Page 14]
Internet-Draft SRv6 OAM March 2020
process. The local OAM process sends a full or partial copy of
the packet P1 to the controller N100. The OAM process includes
the recorded timestamp, additional OAM information like incoming
and outgoing interface, etc. along with any applicable metadata.
Node N4 performs the standard SRv6 SID and SRH processing on the
original packet P1. Specifically, it executes the VPN SID
(B:7:DT100) and based on lookup in table 100 forwards the packet
P1 (IPv4 header)(payload) towards CE 2.
o The controller N100 processes and correlates the copy of the
packets sent from nodes N1, N4 and N7 to find segment-by-segment
delays and provide other passive OAM information related to packet
P1.
o The process continues for any other sampled packets.
6.4. Monitoring of SRv6 Paths
In the recent past, network operators are interested in performing
network OAM functions in a centralized manner. Various data models
like YANG are available to collect data from the network and manage
it from a centralized entity.
SR technology enables a centralized OAM entity to perform path
monitoring from centralized OAM entity without control plane
intervention on monitored nodes. [RFC 8403] describes such a
centralized OAM mechanism. Specifically, the draft describes a
procedure that can be used to perform path continuity check between
any nodes within an SR domain from a centralized monitoring system,
with minimal or no control plane intervene on the nodes. However,
the draft focuses on SR networks with MPLS data plane. The same
concept applies to the SRv6 networks. This document describes how
the concept can be used to perform path monitoring in an SRv6
network. This document describes how the concept can be used to
perform path monitoring in an SRv6 network as follows.
In the above reference topology, N100 is the centralized monitoring
system implementing an END function B:100:1::. In order to verify a
segment list <B:2:C31, B:4:C52>, N100 generates a probe packet with
SRH set to (B:100:1::, B:4:C52, B:2:C31, SL=2). The controller
routes the probe packet towards the first segment, which is B:2:C31.
N2 performs the standard SRv6 SID and SRH processing and forward it
over link3 with the DA of IPv6 packet set to B:4:C52. N4 also
performs the normal SRH processing and forward it over link10 with
the DA of IPv6 packet set to B:100:1::. This makes the probe loops
back to the centralized monitoring system.
Ali, et al. Expires October 1, 2020 [Page 15]
Internet-Draft SRv6 OAM March 2020
In the reference topology in Figure 1, N100 uses an IGP protocol like
OSPF or ISIS to get the topology view within the IGP domain. N100
can also use BGP-LS to get the complete view of an inter-domain
topology. In other words, the controller leverages the visibility of
the topology to monitor the paths between the various endpoints
without control plane intervention required at the monitored nodes.
7. Implementation Status
This section is to be removed prior to publishing as an RFC.
See [I-D.matsushima-spring-srv6-deployment-status] for updated
deployment and interoperability reports.
8. Security Considerations
This document does not define any new protocol extensions and relies
on existing procedures defined for ICMP. This document does not
impose any additional security challenges to be considered beyond
security considerations described in RFC4884, RFC4443, RFC792, RFCs
that updates these RFCs, [I-D.ietf-6man-segment-routing-header] and
[I-D.ietf-spring-srv6-network-programming].
9. IANA Considerations
9.1. ICMPv6 type Numbers Registry
This document defines one ICMPv6 type Number in the "ICMPv6 'type'
Numbers" registry of [RFC4443]. Specifically, the document requests
to add the following ICMPv6 type Number to the "ICMPv6 Type Numbers"
registry:
TBA (suggested value: 162) SRv6 OAM Message.
The document also requests the creation of a new IANA registry to the
"ICMPv6 'Code' Fields" against the "ICMPv6 Type Numbers TBA - SRv6
OAM Message" with the following codes:
Code Name Reference
--------------------------------------------------------
0 No Error This document
1 SID is not locally implemented This document
Ali, et al. Expires October 1, 2020 [Page 16]
Internet-Draft SRv6 OAM March 2020
9.2. SRv6 OAM Endpoint Types
This I-D requests to IANA to allocate, within the "SRv6 Endpoint
Behaviors Registry" sub-registry belonging to the top-level "Segment-
routing with IPv6 data plane (SRv6) Parameters" registry [I-D.ietf-
spring- srv6-network-programming], the following allocations:
+------------------+-------------------+-----------+
| Value (Suggested | Endpoint Behavior | Reference |
| Value) | | |
+------------------+-------------------+-----------+
| TBA (40) | End.OP | [This.ID] |
+------------------+-------------------+-----------+
9.3. Segment Routing Header Flags
This I-D requests to IANA to allocate bit position 2, within the
"Segment Routing Header Flags" registry defined in [I-D.draft-ietf-
6man-segment-routing-header].
10. Acknowledgements
The authors would like to thank Gaurav Naik for his review comments.
11. Contributors
The following people have contributed to this document:
Robert Raszuk
Bloomberg LP
Email: robert@raszuk.net
John Leddy
Individual
Email: john@leddy.net
Gaurav Dawra
LinkedIn
Email: gdawra.ietf@gmail.com
Bart Peirens
Proximus
Email: bart.peirens@proximus.com
Ali, et al. Expires October 1, 2020 [Page 17]
Internet-Draft SRv6 OAM March 2020
Nagendra Kumar
Cisco Systems, Inc.
Email: naikumar@cisco.com
Carlos Pignataro
Cisco Systems, Inc.
Email: cpignata@cisco.com
Rakesh Gandhi
Cisco Systems, Inc.
Canada
Email: rgandhi@cisco.com
Frank Brockners
Cisco Systems, Inc.
Germany
Email: fbrockne@cisco.com
Darren Dukes
Cisco Systems, Inc.
Email: ddukes@cisco.com
Cheng Li
Huawei
Email: chengli13@huawei.com
Faisal Iqbal
Individual
Email: faisal.ietf@gmail.com
12. References
12.1. Normative References
[]
Filsfils, C., Dukes, D., Previdi, S., Leddy, J.,
Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header
(SRH)", draft-ietf-6man-segment-routing-header-26 (work in
progress), October 2019.
Ali, et al. Expires October 1, 2020 [Page 18]
Internet-Draft SRv6 OAM March 2020
[I-D.ietf-spring-srv6-network-programming]
Filsfils, C., Camarillo, P., Leddy, J., Voyer, D.,
Matsushima, S., and Z. Li, "SRv6 Network Programming",
draft-ietf-spring-srv6-network-programming-15 (work in
progress), March 2020.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
12.2. Informative References
[I-D.matsushima-spring-srv6-deployment-status]
Matsushima, S., Filsfils, C., Ali, Z., and Z. Li, "SRv6
Implementation and Deployment Status", draft-matsushima-
spring-srv6-deployment-status-06 (work in progress), March
2020.
[RFC0792] Postel, J., "Internet Control Message Protocol", STD 5,
RFC 792, DOI 10.17487/RFC0792, September 1981,
<https://www.rfc-editor.org/info/rfc792>.
[RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", STD 89,
RFC 4443, DOI 10.17487/RFC4443, March 2006,
<https://www.rfc-editor.org/info/rfc4443>.
[RFC4884] Bonica, R., Gan, D., Tappan, D., and C. Pignataro,
"Extended ICMP to Support Multi-Part Messages", RFC 4884,
DOI 10.17487/RFC4884, April 2007,
<https://www.rfc-editor.org/info/rfc4884>.
[RFC5837] Atlas, A., Ed., Bonica, R., Ed., Pignataro, C., Ed., Shen,
N., and JR. Rivers, "Extending ICMP for Interface and
Next-Hop Identification", RFC 5837, DOI 10.17487/RFC5837,
April 2010, <https://www.rfc-editor.org/info/rfc5837>.
[RFC8403] Geib, R., Ed., Filsfils, C., Pignataro, C., Ed., and N.
Kumar, "A Scalable and Topology-Aware MPLS Data-Plane
Monitoring System", RFC 8403, DOI 10.17487/RFC8403, July
2018, <https://www.rfc-editor.org/info/rfc8403>.
Ali, et al. Expires October 1, 2020 [Page 19]
Internet-Draft SRv6 OAM March 2020
Authors' Addresses
Zafar Ali
Cisco Systems
Email: zali@cisco.com
Clarence Filsfils
Cisco Systems
Email: cfilsfil@cisco.com
Satoru Matsushima
Softbank
Email: satoru.matsushima@g.softbank.co.jp
Daniel Voyer
Bell Canada
Email: daniel.voyer@bell.ca
Mach Chen
Huawei
Email: mach.chen@huawei.com
Ali, et al. Expires October 1, 2020 [Page 20]