AAA Working Group Pat R. Calhoun
Internet-Draft Black Storm Networks
Category: Standards Track Glen Zorn
Cisco Systems, Inc.
David Spence
Interlink Networks, Inc.
David Mitton
Circular Logic
February 2003
Diameter Network Access Server Application
draft-ietf-aaa-diameter-nasreq-11.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft
Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This document is a product of the Authentication, Authorization and
Accounting (AAA) Working Group of the Internet Engineering Task Force
(IETF). Comments are welcome should be submitted to the mailing list
aaa-wg@merit.edu.
Copyright (C) The Internet Society 2003. All Rights Reserved.
Calhoun et al. Expires August 2003 [Page 1]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Abstract
This document describes Diameter applications that are used for
Authentication, Authorization and Accounting (AAA) in the Network
Access Server (NAS) environment. This application, combined with the
Diameter base protocol, Transport Profile, EAP and CMS Security
specifications, satisfies typical network access services
requirements.
Initial deployments of the Diameter protocol are expected to include
legacy systems. Therefore, this application was carefully designed to
ease the burden of protocol conversion between RADIUS and Diameter.
This is achieved by including the RADIUS attribute space, and
eliminating the need to perform many attribute translations.
Calhoun et al. Expires August 2003 [Page 2]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1. Requirements Language . . . . . . . . . . . . . . . . . . . . 6
1.2. Advertising Application Support . . . . . . . . . . . . . . . 6
2. NAS Calls, Ports, and Sessions . . . . . . . . . . . . . . . . . 6
2.1. Diameter Session Establishment . . . . . . . . . . . . . . . . 7
2.2. Diameter Session Re-Authentication or Re-Authorization . . . . 7
2.3. Diameter Session Termination . . . . . . . . . . . . . . . . . 8
3. NAS Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1. AA-Request (AAR) Command . . . . . . . . . . . . . . . . . . . 8
3.2. AA-Answer (AAA) Command . . . . . . . . . . . . . . . . . . . 10
4. NAS Session AVPs . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1. Call and Session Information . . . . . . . . . . . . . . . . . 12
4.2. NAS-Port AVP . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3. NAS-Port-Id AVP . . . . . . . . . . . . . . . . . . . . . . . 13
4.4. NAS-Port-Type AVP . . . . . . . . . . . . . . . . . . . . . . 14
4.5. Called-Station-Id AVP . . . . . . . . . . . . . . . . . . . . 14
4.6. Calling-Station-Id AVP . . . . . . . . . . . . . . . . . . . . 15
4.7. Connect-Info AVP . . . . . . . . . . . . . . . . . . . . . . . 15
4.8. Originating-Line-Info AVP . . . . . . . . . . . . . . . . . . 15
4.9. Reply-Message AVP . . . . . . . . . . . . . . . . . . . . . . 17
4.10. Termination-Action AVP . . . . . . . . . . . . . . . . . . . 17
5. NAS Authentication AVPs . . . . . . . . . . . . . . . . . . . . 18
5.1. User-Password AVP . . . . . . . . . . . . . . . . . . . . . . 19
5.2. Password-Retry AVP . . . . . . . . . . . . . . . . . . . . . . 19
5.3. Prompt AVP . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4. CHAP-Auth AVP . . . . . . . . . . . . . . . . . . . . . . . . 20
5.5. CHAP-Algorithm AVP . . . . . . . . . . . . . . . . . . . . . . 20
5.6. CHAP-Ident AVP . . . . . . . . . . . . . . . . . . . . . . . . 21
5.7. CHAP-Response AVP . . . . . . . . . . . . . . . . . . . . . . 21
5.8. CHAP-Challenge AVP . . . . . . . . . . . . . . . . . . . . . . 21
5.9. ARAP-Password AVP . . . . . . . . . . . . . . . . . . . . . . 21
5.10. ARAP-Challenge-Response AVP . . . . . . . . . . . . . . . . . 21
5.11. ARAP-Security AVP . . . . . . . . . . . . . . . . . . . . . . 21
5.12. ARAP-Security-Data AVP . . . . . . . . . . . . . . . . . . . 22
6. NAS Authorization AVPs . . . . . . . . . . . . . . . . . . . . . 22
6.1. Service-Type AVP . . . . . . . . . . . . . . . . . . . . . . . 23
6.2. Callback-Number AVP . . . . . . . . . . . . . . . . . . . . . 24
6.3. Callback-Id AVP . . . . . . . . . . . . . . . . . . . . . . . 25
6.4. Idle-Timeout AVP . . . . . . . . . . . . . . . . . . . . . . . 25
6.5. Port-Limit AVP . . . . . . . . . . . . . . . . . . . . . . . . 25
6.6. NAS-Filter-Rule AVP . . . . . . . . . . . . . . . . . . . . . 25
6.7. Filter-Id AVP . . . . . . . . . . . . . . . . . . . . . . . . 25
6.8. Configuration-Token AVP . . . . . . . . . . . . . . . . . . . 26
6.9. Framed Access Authorization AVPs . . . . . . . . . . . . . . . 26
6.9.1. Framed-Protocol AVP . . . . . . . . . . . . . . . . . . . . 26
Calhoun et al. Expires August 2003 [Page 3]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.9.2. Framed-Routing AVP . . . . . . . . . . . . . . . . . . . . . 26
6.9.3. Framed-MTU AVP . . . . . . . . . . . . . . . . . . . . . . . 27
6.9.4. Framed-Compression AVP . . . . . . . . . . . . . . . . . . . 27
6.10. IP Access . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.10.1. Framed-IP-Address AVP . . . . . . . . . . . . . . . . . . . 28
6.10.2. Framed-IP-Netmask AVP . . . . . . . . . . . . . . . . . . . 28
6.10.3. Framed-Route AVP . . . . . . . . . . . . . . . . . . . . . 28
6.10.4. Framed-Pool AVP . . . . . . . . . . . . . . . . . . . . . . 29
6.10.5. Framed-Interface-Id AVP . . . . . . . . . . . . . . . . . . 29
6.10.6. Framed-IPv6-Prefix AVP . . . . . . . . . . . . . . . . . . 29
6.10.7. Framed-IPv6-Route AVP . . . . . . . . . . . . . . . . . . . 29
6.10.8. Framed-IPv6-Pool AVP . . . . . . . . . . . . . . . . . . . 30
6.11. IPX Access . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.11.1. Framed-IPX-Network AVP . . . . . . . . . . . . . . . . . . 30
6.12. Appletalk Access . . . . . . . . . . . . . . . . . . . . . . 30
6.12.1. Framed-AppleTalk-Link AVP . . . . . . . . . . . . . . . . . 31
6.12.2. Framed-AppleTalk-Network AVP . . . . . . . . . . . . . . . 31
6.12.3. Framed-AppleTalk-Zone AVP . . . . . . . . . . . . . . . . . 31
6.13. ARAP Access . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.13.1. ARAP-Features AVP . . . . . . . . . . . . . . . . . . . . . 32
6.13.2. ARAP-Zone-Access AVP . . . . . . . . . . . . . . . . . . . 32
6.14. Non-Framed Access Authorization AVPs . . . . . . . . . . . . 32
6.14.1. Login-IP-Host AVP . . . . . . . . . . . . . . . . . . . . . 32
6.14.2. Login-IPv6-Host AVP . . . . . . . . . . . . . . . . . . . . 32
6.14.3. Login-Service AVP . . . . . . . . . . . . . . . . . . . . . 33
6.15. TCP Services . . . . . . . . . . . . . . . . . . . . . . . . 33
6.15.1. Login-TCP-Port AVP . . . . . . . . . . . . . . . . . . . . 33
6.15.2. LAT Services . . . . . . . . . . . . . . . . . . . . . . . 34
6.15.3. Login-LAT-Service AVP . . . . . . . . . . . . . . . . . . . 34
6.15.4. Login-LAT-Node AVP . . . . . . . . . . . . . . . . . . . . 34
6.15.5. Login-LAT-Group AVP . . . . . . . . . . . . . . . . . . . . 35
6.15.6. Login-LAT-Port AVP . . . . . . . . . . . . . . . . . . . . 35
7. Tunneling Group AVPs . . . . . . . . . . . . . . . . . . . . . . 36
7.1. Tunnel-Type AVP . . . . . . . . . . . . . . . . . . . . . . . 37
7.2. Tunnel-Medium-Type AVP . . . . . . . . . . . . . . . . . . . . 37
7.3. Tunnel-Client-Endpoint AVP . . . . . . . . . . . . . . . . . . 38
7.4. Tunnel-Server-Endpoint AVP . . . . . . . . . . . . . . . . . . 39
7.5. Tunnel-Password AVP . . . . . . . . . . . . . . . . . . . . . 39
7.6. Tunnel-Private-Group-Id AVP . . . . . . . . . . . . . . . . . 40
7.7. Tunnel-Assignment-Id AVP . . . . . . . . . . . . . . . . . . . 40
7.8. Tunnel-Preference AVP . . . . . . . . . . . . . . . . . . . . 41
7.9. Tunnel-Client-Auth-Id AVP . . . . . . . . . . . . . . . . . . 42
7.10. Tunnel-Server-Auth-Id AVP . . . . . . . . . . . . . . . . . . 42
8. NAS Accounting . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.1. Accounting-Input-Octets AVP . . . . . . . . . . . . . . . . . 43
8.2. Accounting-Output-Octets AVP . . . . . . . . . . . . . . . . . 44
8.3. Accounting-Input-Packets AVP . . . . . . . . . . . . . . . . . 44
8.4. Accounting-Output-Packets AVP . . . . . . . . . . . . . . . . 44
Calhoun et al. Expires August 2003 [Page 4]
INTERNET-DRAFT Diameter NAS Application Feb 2003
8.5. Acct-Session-Time AVP . . . . . . . . . . . . . . . . . . . . 44
8.6. Acct-Authentic AVP . . . . . . . . . . . . . . . . . . . . . . 44
8.7. Acct-Delay-Time . . . . . . . . . . . . . . . . . . . . . . . 45
8.8. Acct-Link-Count . . . . . . . . . . . . . . . . . . . . . . . 45
8.9. Acct-Tunnel-Connection AVP . . . . . . . . . . . . . . . . . . 46
8.10. Acct-Tunnel-Packets-Lost AVP . . . . . . . . . . . . . . . . 46
9. RADIUS/Diameter Protocol Interactions . . . . . . . . . . . . . 46
9.1. RADIUS Request Forwarded as Diameter Request . . . . . . . . . 47
9.1.1. Diameter Request Forwarded as RADIUS Request . . . . . . . . 50
9.2. AVPs Used Only for Compatibility . . . . . . . . . . . . . . . 51
9.2.1. NAS-Identifier AVP . . . . . . . . . . . . . . . . . . . . . 51
9.2.2. NAS-IP-Address AVP . . . . . . . . . . . . . . . . . . . . . 52
9.2.3. NAS-IPv6-Address AVP . . . . . . . . . . . . . . . . . . . . 52
9.2.4. State AVP . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.2.5. Termination-Cause AVP Code Values . . . . . . . . . . . . . 54
9.3. Prohibited RADIUS Attributes . . . . . . . . . . . . . . . . . 56
9.4. Translatable Diameter AVPs . . . . . . . . . . . . . . . . . . 56
9.5. RADIUS Vendor Specific Attributes . . . . . . . . . . . . . . 56
9.5.1. Forwarding a Diameter Vendor AVP as a RADIUS VSA . . . . . . 56
9.5.2. Forwarding a RADIUS VSA to a Diameter Vendor AVP . . . . . . 57
10. AVP Occurrence Tables . . . . . . . . . . . . . . . . . . . . . 57
10.1. AA-Request/Answer AVP Table . . . . . . . . . . . . . . . . . 58
10.2. Accounting AVP Tables . . . . . . . . . . . . . . . . . . . . 61
10.2.1. Accounting Framed Access AVP Table . . . . . . . . . . . . 61
10.2.2. Accounting Non-Framed Access AVP Table . . . . . . . . . . 62
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 64
11.1. Command Codes . . . . . . . . . . . . . . . . . . . . . . . . 64
11.2. AVP Codes . . . . . . . . . . . . . . . . . . . . . . . . . . 64
11.3. Application Identifier . . . . . . . . . . . . . . . . . . . 64
11.4. CHAP-Algorithm AVP Values . . . . . . . . . . . . . . . . . . 64
12. Security Considerations . . . . . . . . . . . . . . . . . . . . 65
13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.1. Normative References . . . . . . . . . . . . . . . . . . . . 65
13.2. Informative References . . . . . . . . . . . . . . . . . . . 66
14. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 68
15. Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 68
Intellectual Property Considerations . . . . . . . . . . . . . . . . 69
Full Copyright Statement . . . . . . . . . . . . . . . . . . . . . . 70
Calhoun et al. Expires August 2003 [Page 5]
INTERNET-DRAFT Diameter NAS Application Feb 2003
1. Introduction
This document describes Diameter applications that are used for AAA
in the Network Access Server (NAS) environment. The Diameter NAS
application, when combined with the Diameter base protocol [Base],
Transport Profile [DiamTrans] EAP [DiamEAP], and CMS Security
[DiamCMS] specifications, satisfies NAS-related requirements defined
in RFC2989 [AAACriteria] and RFC3169 [NASCriteria].
Initial deployments of the Diameter protocol are expected to include
legacy systems. Therefore, this application was carefully designed to
ease the burden of protocol conversion between RADIUS and Diameter.
This is achieved by including the RADIUS attribute space, and
eliminating the need to perform many attribute translations.
This document first describes the operation of a Diamter NAS
application. Then it defines the Diameter message Command-Codes.
The following sections enumerate the AVPs used in these messages
grouped by common usage. These are Session Identification,
Authentication, Authorization, and Accounting. The Authorization
AVPs are further broken down by service type. Interaction and
backwards compatibility issues with RADIUS are discussed in later
sections.
1.1. Requirements Language
In this document, the key words "MAY", "MUST", "MUST NOT",
"OPTIONAL", "RECOMMENDED", "SHOULD", and "SHOULD NOT", are to be
interpreted as described in [Keywords].
1.2. Advertising Application Support
Diameter nodes conforming to this specification MAY advertise support
by including the value of one (1) in the Auth-Application-Id or the
Acct-Application-Id AVP of the Capabilities-Exchange-Request and
Capabilities-Exchange-Answer commands [Base].
2. NAS Calls, Ports, and Sessions
The arrival of a new call or service connection at a port of a
Network Access Server (NAS) starts a Diameter NAS message exchange.
Information about the call, the identity of the user, and his
authentication information are packaged into a Diameter AA-Request
(AAR) message and sent to a server.
Calhoun et al. Expires August 2003 [Page 6]
INTERNET-DRAFT Diameter NAS Application Feb 2003
The server processes the information and responds with a Diameter AA-
Answer (AAA) message which contains authorization information for the
NAS, or a failure code (Result-Code AVP). If the value of Result-
Code is DIAMETER_MULTI_ROUND_AUTH, an additional authentication
exchange is indicated, and several AAR and AAA messages may be
exchanged until the transaction completes.
Unlike the RADIUS protocol [RADIUS], the Diameter protocol does not
require authentication information to be contained in a request from
the client. Therefore, it is possible to send a request for
authorization only. The type of service depends upon the Auth-
Request-Type AVP. This difference MAY cause operational issues in
environments that need RADIUS interoperability, and it MAY be
necessary that protocol conversion gateways add authentication
information when transmitting to a RADIUS server.
2.1. Diameter Session Establishment
When the authentication or authorization exchange completes
successfully, the NAS application SHOULD start a session context, and
MAY send an Accounting START_RECORD message [Base]. The failure to
start a session SHOULD cause an Accounting EVENT_RECORD message.
2.2. Diameter Session Re-Authentication or Re-Authorization
The Diameter protocol allows for users to be periodically re-
authenticated and/or re-authorized. In such instances, the Session-Id
AVP in the AAR message MUST be the same as the one present in the
original authentication/authorization message. A Diameter server
informs the NAS of the maximum time allowed before re-authentication
or re-authorization via the Authorization-Lifetime AVP [Base]. Note,
however, that the Authorization-Lifetime AVP SHOULD NOT be used if
the AAR message contained a NAS-IP-Address, NAS-IPv6-Address, or NAS-
Identifier AVP since this would mean that the NAS is using RADIUS
which does not support server-initiated re-authentication or re-
authorization.
A NAS MUST re-authenticate and/or authorize after the period provided
by the server. Furthermore, it is possible for Diameter servers to
issue an unsolicited re-authentication and/or re-authorization by
issuing an Re-Auth-Request message to the NAS. Upon receipt of such a
message, the NAS is instructed to issue a request to re-authenticate
and/or re-authorize the client.
Calhoun et al. Expires August 2003 [Page 7]
INTERNET-DRAFT Diameter NAS Application Feb 2003
2.3. Diameter Session Termination
When a NAS receives an indication that a user's session is being
disconnected (e.g. LCP Terminate is received), the NAS MUST issue a
Session-Termination-Request (STR) [Base] to its Diameter Server. This
will ensure that any resources maintained on the servers is freed
appropriately.
Further, a NAS that receives a Abort-Session-Request (ASR) [Base]
MUST issue an STR if the session requested is active, and disconnect
the PPP (or tunneling) session.
Termination of the session context, MUST cause the sending of an
Accounting STOP_RECORD message [Base], if accounting is active.
More information on Diameter Session Termination is in [Base] section
8.4.
3. NAS Messages
This section defines new Diameter message Command-Code [Base] values
that MUST be supported by all Diameter implementations that conform
to this specification. The Command Codes are:
Command-Name Abbrev. Code Reference
--------------------------------------------------------
AA-Request AAR 265 3.1
AA-Answer AAA 265 3.2
3.1. AA-Request (AAR) Command
The AA-Request message (AAR), indicated by the Command-Code field set
to 265 and the 'R' bit set in the Command Flags field, is used in
order to request authentication and/or authorization for a given NAS
user. The type of request is identified through the Auth-Request-Type
AVP, and the default mode is both authentication and authorization.
If Authentication is requested the User-Name attribute SHOULD be
present, as well as any additional authentication AVPs that would
carry the password information. A request for authorization only
SHOULD include the information from which the authorization will be
performed, such as the User-Name, Called-Station-Id, or Calling-
Station-Id AVPs. All requests SHOULD contain AVPs uniquely identifing
the source of the call, such as Origin-Host, and NAS-Port. Certain
networks MAY use different AVPs for authorization purposes. A request
Calhoun et al. Expires August 2003 [Page 8]
INTERNET-DRAFT Diameter NAS Application Feb 2003
for authorization will include some AVPs defined in section 6.
It is possible for a single session to be authorized first, then
followed by an authentication request.
This AA-Request message MAY be the result of a multi-round
authentication exchange, which occurs when the AA-Answer message is
received with the Result-Code AVP set to DIAMETER_MULTI_ROUND_AUTH. A
subsequent AAR message SHOULD be sent, with the User-Password AVP
that includes the user's response to the prompt, and MUST include any
State AVPs that were present in the AAA message.
Message Format
<AA-Request> ::= < Diameter Header: 265, REQ, PXY >
< Session-Id >
{ Auth-Application-Id }
{ Origin-Host }
{ Origin-Realm }
{ Destination-Realm }
{ Auth-Request-Type }
[ NAS-Port ]
[ NAS-Port-Id ]
[ Origin-State-Id ]
[ Destination-Host ]
[ NAS-Identifier ]
[ NAS-IP-Address ]
[ NAS-IPv6-Address ]
[ NAS-Port-Type ]
[ Port-Limit ]
[ User-Name ]
[ User-Password ]
[ Service-Type ]
[ Idle-Timeout ]
[ State ]
[ Authorization-Lifetime ]
[ Auth-Grace-Period ]
[ Auth-Session-State ]
[ Session-Timeout ]
[ Callback-Number ]
[ Called-Station-Id ]
[ Calling-Station-Id ]
* [ Class ]
[ Originating-Line-Info ]
[ Connect-Info ]
[ CHAP-Auth ]
[ CHAP-Challenge ]
* [ Framed-Compression ]
Calhoun et al. Expires August 2003 [Page 9]
INTERNET-DRAFT Diameter NAS Application Feb 2003
[ Framed-Interface-Id ]
[ Framed-IP-Address ]
* [ Framed-IPv6-Prefix ]
[ Framed-IP-Netmask ]
[ Framed-MTU ]
[ Framed-Protocol ]
[ ARAP-Password ]
[ ARAP-Security ]
* [ ARAP-Security-Data ]
* [ Login-IP-Host ]
* [ Login-IPv6-Host ]
[ Login-LAT-Group ]
[ Login-LAT-Node ]
[ Login-LAT-Port ]
[ Login-LAT-Service ]
* [ Tunneling ]
* [ Proxy-Info ]
* [ Route-Record ]
* [ AVP ]
3.2. AA-Answer (AAA) Command
The AA-Answer (AAA) message, is indicated by the Command-Code field
set to 265 and the 'R' bit cleared in the Command Flags field, is
sent in response to the AA-Request message. If authorization was
requested, a successful response will include the authorization AVPs
appropriate for the service being provided, as defined in section 6.
For authentication exchanges that require more than a single round
trip, the server MUST set the Result-Code AVP to
DIAMETER_MULTI_ROUND_AUTH. An AAA message with this result code MAY
include one or more Reply-Message and MAY include zero or one State
AVPs.
If the Reply-Message AVP was present, the access device SHOULD
display the text message to the user, and MUST prompt the user for a
response. If the access device is unable to prompt the user for a
new response, which could be achieved via PAP, it MUST treat this
answer as an error, and deny access.
Calhoun et al. Expires August 2003 [Page 10]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Message Format
<AA-Answer> ::= < Diameter Header: 265, PXY >
< Session-Id >
{ Auth-Application-Id }
{ Auth-Request-Type }
{ Result-Code }
{ Origin-Host }
{ Origin-Realm }
[ User-Name ]
[ Service-Type ]
* [ Class ]
* [ Configuration-Token ]
[ Acct-Interim-Interval ]
[ Error-Message ]
[ Error-Reporting-Host ]
[ Idle-Timeout ]
[ Authorization-Lifetime ]
[ Auth-Grace-Period ]
[ Auth-Session-State ]
[ Re-Auth-Request-Type ]
[ Session-Timeout ]
[ State ]
* [ Reply-Message ]
[ Termination-Action ]
[ Origin-State-Id ]
* [ Filter-Id ]
[ Password-Retry ]
[ Port-Limit ]
[ Prompt ]
[ ARAP-Challenge-Response ]
[ ARAP-Features ]
[ ARAP-Security ]
* [ ARAP-Security-Data ]
[ ARAP-Zone-Access ]
[ Callback-Id ]
[ Callback-Number ]
[ Framed-Appletalk-Link ]
* [ Framed-Appletalk-Network ]
[ Framed-Appletalk-Zone ]
* [ Framed-Compression ]
[ Framed-Interface-Id ]
[ Framed-IP-Address ]
* [ Framed-IPv6-Prefix ]
[ Framed-IPv6-Pool ]
* [ Framed-IPv6-Route ]
[ Framed-IP-Netmask ]
* [ Framed-Route ]
Calhoun et al. Expires August 2003 [Page 11]
INTERNET-DRAFT Diameter NAS Application Feb 2003
[ Framed-Pool ]
[ Framed-IPX-Network ]
[ Framed-MTU ]
[ Framed-Protocol ]
[ Framed-Routing ]
* [ Login-IP-Host ]
* [ Login-IPv6-Host ]
[ Login-LAT-Group ]
[ Login-LAT-Node ]
[ Login-LAT-Port ]
[ Login-LAT-Service ]
[ Login-Service ]
[ Login-TCP-Port ]
* [ NAS-Filter-Rule ]
* [ Tunneling ]
* [ Redirect-Host ]
[ Redirect-Host-Usage ]
[ Redirect-Max-Cache-Time ]
* [ Proxy-Info ]
* [ AVP ]
4. NAS Session AVPs
Diameter reserves the AVP Codes 0-255 for RADIUS functions that are
implemented in Diameter.
AVPs new to Diameter have code values 256 and greater. A Diameter
message that includes one of these AVPs MAY cause interoperability
issues should the request traverse a AAA node that only supports the
RADIUS protocol. However, the Diameter protocol should not be
hampered from future developments due to the existing installed base.
There are some RADIUS attributes that are not allowed or supported
directly in Diameter. See section 9 below for more information.
4.1. Call and Session Information
This section contains the NAS unique AVPs that are needed to identify
call and session context information, and allows the server to set
constraints on a session.
These AVPs are used in addition to the Base AVPs of:
Session-Id
Auth-Application-Id
Origin-Host
Origin-Realm
Calhoun et al. Expires August 2003 [Page 12]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Auth-Request-Type
Common session status AVPs are listed here too.
The following table describes the Session level AVPs, their AVP Code
values, types, possible flag values and whether the AVP MAY be
encrypted.
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
AVP Section | | |SHLD| MUST| |
Attribute Name Code Defined Value Type |MUST| MAY | NOT| NOT|Encr|
-----------------------------------------|----+-----+----+-----|----|
NAS-Port 5 4.2 Unsigned32 | M | P | | V | Y |
NAS-Port-Id 87 4.3 UTF8String | M | P | | V | Y |
NAS-Port-Type 61 4.4 Enumerated | M | P | | V | Y |
Called-Station-Id 30 4.5 UTF8String | M | P | | V | Y |
Calling-Station- 31 4.6 UTF8String | M | P | | V | Y |
Id | | | | | |
Connect-Info 77 4.7 UTF8String | M | P | | V | Y |
Originating-Line- 94 4.8 OctetString| | M,P | | V | Y |
Info | | | | | |
Reply-Message 18 4.9 UTF8String | M | P | | V | Y |
Termination- 29 4.10 Enumerated | M | P | | V | Y |
Action | | | | | |
-----------------------------------------|----+-----+----+-----|----|
4.2. NAS-Port AVP
The NAS-Port AVP (AVP Code 5) is of type Unsigned32 and contains the
physical or virtual port number of the NAS which is authenticating
the user. Note that this is using "port" in its sense of a service
connection on the NAS, not in the sense of an IP protocol identifier.
Either NAS-Port or NAS-Port-Id (AVP Code 87) SHOULD be present in AA-
Request commands if the NAS differentiates among its ports.
4.3. NAS-Port-Id AVP
The NAS-Port-Id AVP (AVP Code 87) is of type UTF8String and consists
of ASCII text that identifies the port of the NAS which is
authenticating the user. Note that this is using "port" in its sense
of a service connection on the NAS, not in the sense of an IP
protocol identifier.
Calhoun et al. Expires August 2003 [Page 13]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Either NAS-Port or NAS-Port-Id SHOULD be present in AA-Request
commands if the NAS differentiates among its ports. NAS-Port-Id is
intended for use by NASes which cannot conveniently number their
ports.
4.4. NAS-Port-Type AVP
The NAS-Port-Type AVP (AVP Code 61) is of type Enumerated and
contains the type of the port on which the NAS is authenticating the
user. This AVP SHOULD be present if the NAS uses the same NAS-Port
number ranges for different service types concurrently.
The supported values are defined in [RADIUSTypes]. The following list
is informational:
0 Async
1 Sync
2 ISDN Sync
3 ISDN Async V.120
4 ISDN Async V.110
5 Virtual
6 PIAFS
7 HDLC Clear Channel
8 X.25
9 X.75
10 G.3 Fax
11 SDSL - Symmetric DSL
12 ADSL-CAP - Asymmetric DSL, Carrierless Amplitude Phase
Modulation
13 ADSL-DMT - Asymmetric DSL, Discrete Multi-Tone
14 IDSL - ISDN Digital Subscriber Line
15 Ethernet
16 xDSL - Digital Subscriber Line of unknown type
17 Cable
18 Wireless - Other
19 Wireless - IEEE 802.11
4.5. Called-Station-Id AVP
The Called-Station-Id AVP (AVP Code 30) is of type UTF8String, and
allows the NAS to send in the request, the ASCII string of the phone
number that the user called, using Dialed Number Identification
(DNIS) or a similar technology. Note that this may be different from
the phone number the call comes in on. It SHOULD only be present in
Calhoun et al. Expires August 2003 [Page 14]
INTERNET-DRAFT Diameter NAS Application Feb 2003
authentication and/or authorization requests.
If the Auth-Request-Type AVP is set to authorization-only and the
User-Name AVP is absent, the Diameter Server MAY perform
authorization based on this field. This can be used by a NAS to
request whether a call should be answered based on the DNIS.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
4.6. Calling-Station-Id AVP
The Calling-Station-Id AVP (AVP Code 31) is of type UTF8String, and
allows the NAS to send in the request the the ASCII string of the
phone number that the call came from, using Automatic Number
Identification (ANI) or a similar technology. It SHOULD only be
present in authentication and/or authorization requests.
If the Auth-Request-Type AVP is set to authorization-only and the
User-Name AVP is absent, the Diameter Server MAY perform
authorization based on this field. This can be used by a NAS to
request whether a call should be answered based on the ANI.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
4.7. Connect-Info AVP
The Connect-Info AVP (AVP Code 77) is of type UTF8String and is sent
in the AA-Request message, and indicates the nature of the user's
connection. The connection speed SHOULD be included at the beginning
of the first Connect-Info AVP in the message. If the transmit and
receive connection speeds differ, they may both be included in the
first AVP with the transmit speed first (the speed the NAS modem
transmits at), a slash (/), the receive speed, then optionally other
information.
For example, "28800 V42BIS/LAPM" or "52000/31200 V90"
4.8. Originating-Line-Info AVP
The Originating-Line-Info AVP (AVP Code 94 is of type OctetString and
is sent by the NAS system to convey information about the origin of
Calhoun et al. Expires August 2003 [Page 15]
INTERNET-DRAFT Diameter NAS Application Feb 2003
the call from an SS7 system.
The originating line information (OLI) information element indicates
the nature and/or characteristics of the line from which a call
originated (e.g. payphone, hotel, cellular). Telephone companies are
starting to offer OLI to their customers as an option over Primary
Rate Interface (PRI). Internet Service Providers (ISPs) can use OLI
in addition to Called-Station-Id and Calling-Station-Id attributes to
differentiate customer calls and define different services
The Value field contains two octets (00-99). ANSI T1.113 and BELLCORE
394 can be used for additional information about those values and
their use. For more information on current assignment values see
[ANITypes].
Value Description
------------------------------------------------------------
00 Plain Old Telephone Service (POTS)
01 Multiparty line (more than 2)
02 ANI Failure
03 ANI Observed
04 ONI Observed
05 ANI Failure Observed
06 Station Level Rating
07 Special Operator Handling Required
08 InterLATA Restricted
10 Test Call
20 Automatic Identified Outward Dialing (AIOD)
23 Coin or Non-Coin
24 Toll Free Service (Non-Pay origination)
25 Toll Free Service (Pay origination)
27 Toll Free Service (Coin Control origination)
29 Prison/Inmate Service
30-32 Intercept
30 Intercept (blank)
31 Intercept (trouble)
32 Intercept (regular)
34 Telco Operator Handled Call
40-49 Unrestricted Use
52 Outward Wide Area Telecommunications Service (OUTWATS)
60 Telecommunications Relay Service (TRS)(Unrestricted)
61 Cellular/Wireless PCS (Type 1)
62 Cellular/Wireless PCS (Type 2)
63 Cellular/Wireless PCS (Roaming)
66 TRS (Hotel)
67 TRS (Restricted)
Calhoun et al. Expires August 2003 [Page 16]
INTERNET-DRAFT Diameter NAS Application Feb 2003
70 Pay Station, No coin control
93 Access for private virtual network service
4.9. Reply-Message AVP
The Reply-Message AVP (AVP Code 18) is of type UTF8String, and
contains text which MAY be displayed to the user. When used in an
AA-Answer message with a successful Result-Code AVP it indicates a
success message. When found in the same message with a Result-Code
other than Diameter-SUCCESS it contains a failure message.
The Reply-Message AVP MAY indicate a dialog message to prompt the
user before another AA-Request attempt. When used in an AA-Answer, it
MAY indicate a dialog message to prompt the user for a response.
Multiple Reply-Message's MAY be included and if any are displayed,
they MUST be displayed in the same order as they appear in the
message.
4.10. Termination-Action AVP
The Termination-Action AVP is of type Enumerated and indicates what
action the NAS should take when the specified service is completed.
This AVP SHOULD only be present in authorization responses. The
following values are supported as listed in [RADIUSTypes]:
DEFAULT 0
Upon termination of the authorized service the NAS MUST
terminate the current session.
AA-REQUEST 1
Upon termination of the authorized service the NAS MAY send a
new AA-Request (AAR) command. When the authorized service
terminates, the NAS SHOULD NOT terminate the session or
generate a Session-Termination-Request (STR) command. Instead,
it SHOULD generate a new AAR command which contains the same
value of the Session-Id AVP it sent in the previous AAR
command. It SHOULD also include the State AVP from the
previous AA-Answer (AAA) command if it contained one.
An exception to this rule applies, however, if the authorized
service terminates due to the expiry of the Session-Timeout
AVP. In this case, the NAS MUST terminate the expired session
and MAY generate a new AAR command with a new Session-Id.
Calhoun et al. Expires August 2003 [Page 17]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Note: The Termination-Action AVP is typically used for the login
service (Service-Type = 1 or "Login") or by 802.1X supplicants
[RAD802.1X] (e.g., NAS-Port-Type = 19 or "Wireless - IEEE 802.11").
When used for the login service, the service typically terminates
when the login host clears the connection. The NAS may prompt the
user for a new connection and issue a new AA-Request.
When used by 802.1X supplicants, the service typically terminates due
to the expiry of the Session-Timeout AVP. The access device may then
reauthenticate the user with a new AA-Request. The RECOMMENDED way
to do this in Diameter is to use the Authorization-Lifetime AVP
rather than the Termination-Action AVP. However, the Termination-
Action AVP MAY be used when copied from a RADIUS Access-Accept to a
Diameter AA-Answer by a Translation Agent.
5. NAS Authentication AVPs
This section defines the AVPs that are necessary to carry the
authentication information in the Diameter protocol. The
functionality defined here provides a RADIUS-like AAA service, over a
more reliable and secure transport, as defined in the base protocol
[Base].
The following table describes the AVPs, their AVP Code values, types,
possible flag values and whether the AVP MAY be encrypted.
Calhoun et al. Expires August 2003 [Page 18]
INTERNET-DRAFT Diameter NAS Application Feb 2003
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
AVP Section | | |SHLD| MUST| |
Attribute Name Code Defined Value Type |MUST| MAY | NOT| NOT|Encr|
-----------------------------------------|----+-----+----+-----|----|
User-Password 2 5.1 OctetString| M | P | | V | Y |
Password-Retry 75 5.2 Unsigned32 | M | P | | V | Y |
Prompt 76 5.3 Enumerated | M | P | | V | Y |
CHAP-Auth 402 5.4 Grouped | M | P | | V | Y |
CHAP-Algorithm 403 5.5 Enumerated | M | P | | V | Y |
CHAP-Ident 404 5.6 OctetString| M | P | | V | Y |
CHAP-Response 405 5.7 OctetString| M | P | | V | Y |
CHAP-Challenge 60 5.8 OctetString| M | P | | V | Y |
ARAP-Password 70 5.9 OctetString| M | P | | V | Y |
ARAP-Challenge- 84 5.10 OctetString| M | P | | V | Y |
Response | | | | | |
ARAP-Security 73 5.11 Unsigned32 | M | P | | V | Y |
ARAP-Security- 74 5.12 OctetString| M | P | | V | Y |
Data | | | | | |
-----------------------------------------|----+-----+----+-----|----|
5.1. User-Password AVP
The User-Password AVP (AVP Code 2) is of type OctetString and
contains the password of the user to be authenticated, or the user's
input in a multi-round authentication exchange.
The User-Password AVP contains a user password or one-time password
and therefore represents sensitive information. As required in
[Base], Diameter messages are encrypted using IPsec or TLS. Unless
this AVP is used for one-time passwords, the User- Password AVP
SHOULD NOT be used in untrusted proxy environments without encrypting
it using end-to-end security techniques, such as CMS Security
[DiamCMS].
The clear-text password (prior to encryption) MUST NOT be longer than
128 bytes in length.
5.2. Password-Retry AVP
The Password-Retry AVP (AVP Code 75) is of type Unsigned32 and MAY be
included in the AA-Answer if the Result-Code indicates an
authentication failure. The value of this AVP indicates how many
authentication attempts a user may be permitted before being
disconnected. This AVP is primarily intended for use when the Framed-
Calhoun et al. Expires August 2003 [Page 19]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Protocol AVP (see Section 6.9.1) is set to ARAP.
5.3. Prompt AVP
The Prompt AVP (AVP Code 76) is of type Enumerated, and MAY be
present in the AA-Answer message. When present, it is used by the NAS
to determine whether the user's response, when entered, should be
echoed.
The supported values are listed in [RADIUSTypes]. The following list
is informational:
0 No Echo
1 Echo
5.4. CHAP-Auth AVP
The CHAP-Auth AVP (AVP Code 402) is of type Grouped and contains the
information necessary to authenticate a user using the PPP Challenge-
Handshake Authentication Protocol (CHAP) [PPPCHAP]. If the CHAP-Auth
AVP is found in a message, the CHAP-Challenge AVP MUST be present as
well. The optional AVPs containing the CHAP response depend upon the
value of the CHAP-Algorithm AVP. The grouped AVP has the following
ABNF grammar:
CHAP-Auth ::= < AVP Header: 402 >
{ CHAP-Algorithm }
{ CHAP-Ident }
[ CHAP-Response ]
* [ AVP ]
5.5. CHAP-Algorithm AVP
The CHAP-Algorithm AVP (AVP Code 403) is of type Enumerated and
contains the algorithm identifier used in the computation of the CHAP
response [PPPCHAP]. The following values are currently supported:
CHAP with MD5 5
The CHAP response is computed using the procedure described in
[PPPCHAP]. This algorithm requires that CHAP-Response AVP MUST
be present in the CHAP-Auth AVP.
Calhoun et al. Expires August 2003 [Page 20]
INTERNET-DRAFT Diameter NAS Application Feb 2003
5.6. CHAP-Ident AVP
The CHAP-Ident AVP (AVP Code 404) is of type OctetString and contains
the one octet CHAP Identifier used in the computation of the CHAP
response [PPPCHAP].
5.7. CHAP-Response AVP
The CHAP-Response AVP (AVP Code 405) is of type OctetString and
contains the 16 octet authentication data provided by the user in
response to the CHAP challenge [PPPCHAP].
5.8. CHAP-Challenge AVP
The CHAP-Challenge AVP (AVP Code 60) is of type OctetString and
contains the CHAP Challenge sent by the NAS to the CHAP peer
[PPPCHAP].
5.9. ARAP-Password AVP
The ARAP-Password AVP (AVP Code 70) is of type OctetString and is
only present when the Framed-Protocol AVP (see Section 6.9.1) is
included in the message and is set to ARAP. This AVP MUST NOT be
present if either the User-Password or the CHAP-Auth AVP is present.
See [RADIUSExt] for more information on the contents of this AVP.
5.10. ARAP-Challenge-Response AVP
The ARAP-Challenge-Response AVP (AVP Code 84) is of type OctetString
and is only present when the Framed-Protocol AVP (see Section 6.9.1)
is included in the message and is set to ARAP. This AVP contains an 8
octet response to the dial-in client's challenge. The RADIUS server
calculates this value by taking the dial-in client's challenge from
the high order 8 octets of the ARAP-Password AVP and performing DES
encryption on this value with the authenticating user's password as
the key. If the user's password is less than 8 octets in length, the
password is padded at the end with NULL octets to a length of 8
before using it as a key.
5.11. ARAP-Security AVP
The ARAP-Security AVP (AVP Code 73) is of type Unsigned32, and MAY be
present in the AA-Answer message if the Framed-Protocol AVP (see
Calhoun et al. Expires August 2003 [Page 21]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Section 6.9.1) is set to the value of ARAP, and the Result-Code AVP
is set to DIAMETER_MULTI_ROUND_AUTH. See [RADIUSExt] for more
information on the format of this AVP.
5.12. ARAP-Security-Data AVP
The ARAP-Security AVP (AVP Code 74) is of type OctetString, and MAY
be present in the AA-Request or AA-Answer message if the Framed-
Protocol AVP is set to the value of ARAP, and the Result-Code AVP is
set to DIAMETER_MULTI_ROUND_AUTH. This AVP contains the security
module challenge or response associated with the ARAP Security Module
specified in ARAP-Security.
6. NAS Authorization AVPs
This section contains the authorization AVPs that are supported in
the NAS Application. The Service-Type AVP SHOULD be present in all
messages, and based on its value, additional AVPs defined in this
section and section 7 MAY be present.
Due to space constraints, the short form IPFiltrRule is used to
represent IPFilterRule.
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
AVP Section | | |SHLD| MUST| |
Attribute Name Code Defined Value Type |MUST| MAY | NOT| NOT|Encr|
-----------------------------------------|----+-----+----+-----|----|
Service-Type 6 6.1 Enumerated | M | P | | V | Y |
Callback-Number 19 6.2 UTF8String | M | P | | V | Y |
Callback-Id 20 6.3 UTF8String | M | P | | V | Y |
Idle-Timeout 28 6.4 Unsigned32 | M | P | | V | Y |
Port-Limit 62 6.5 Unsigned32 | M | P | | V | Y |
NAS-Filter-Rule 400 6.6 IPFiltrRule| M | P | | V | Y |
Filter-Id 11 6.7 UTF8String | M | P | | V | Y |
Configuration- 78 6.8 OctetString| M | | | P,V | |
Token | | | | | |
Framed-Protocol 7 6.9.1 Enumerated | M | P | | V | Y |
Framed-Routing 10 6.9.2 Enumerated | M | P | | V | Y |
Framed-MTU 12 6.9.3 Unsigned32 | M | P | | V | Y |
Framed- 13 6.9.4 Enumerated | M | P | | V | Y |
Compression | | | | | |
Framed-IP-Address 8 6.10.1 OctetString| M | P | | V | Y |
Framed-IP-Netmask 9 6.10.2 OctetString| M | P | | V | Y |
Framed-Route 22 6.10.3 UTF8String | M | P | | V | Y |
Framed-Pool 88 6.10.4 OctetString| M | P | | V | Y |
Calhoun et al. Expires August 2003 [Page 22]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Framed- 96 6.10.5 Unsigned64 | M | P | | V | Y |
Interface-Id | | | | | |
Framed-IPv6- 97 6.10.6 OctetString| M | P | | V | Y |
Prefix | | | | | |
Framed-IPv6- 99 6.10.7 UTF8String | M | P | | V | Y |
Route | | | | | |
Framed-IPv6-Pool 100 6.10.8 OctetString| M | P | | V | Y |
Framed-IPX- 23 6.11.1 UTF8String | M | P | | V | Y |
Network | | | | | |
Framed-Appletalk- 37 6.12.1 Unsigned32 | M | P | | V | Y |
Link | | | | | |
Framed-Appletalk- 38 6.12.2 Unsigned32 | M | P | | V | Y |
Network | | | | | |
Framed-Appletalk- 39 6.12.3 OctetString| M | P | | V | Y |
Zone | | | | | |
ARAP-Features 71 6.13.1 OctetString| M | P | | V | Y |
ARAP-Zone-Access 72 6.13.2 Enumerated | M | P | | V | Y |
Login-IP-Host 14 6.14.1 OctetString| M | P | | V | Y |
Login-IPv6-Host 98 6.14.2 OctetString| M | P | | V | Y |
Login-Service 15 6.14.3 Enumerated | M | P | | V | Y |
Login-TCP-Port 16 6.15.1 Unsigned32 | M | P | | V | Y |
Login-LAT-Service 34 6.16.1 OctetString| M | P | | V | Y |
Login-LAT-Node 35 6.16.2 OctetString| M | P | | V | Y |
Login-LAT-Group 36 6.16.3 OctetString| M | P | | V | Y |
Login-LAT-Port 63 6.16.4 OctetString| M | P | | V | Y |
-----------------------------------------|----+-----+----+-----|----|
6.1. Service-Type AVP
The Service-Type AVP (AVP Code 6) is of type Enumerated and contains
the type of service the user has requested, or the type of service to
be provided. One such AVP MAY be present in an authentication and/or
authorization request or response. A NAS is not required to implement
all of these service types, and MUST treat unknown or unsupported
Service-Types as though a response with a Result-Code other than
Diameter-SUCCESS had been received instead.
When used in a request, the Service-Type AVP SHOULD be considered to
be a hint to the server that the NAS has reason to believe the user
would prefer the kind of service indicated, but the server is not
required to honor the hint. The following values have been defined
for the Service-Type AVP:
The complete list of defined values can be found in [RADIUS] and
[RADIUSTypes]. The following list is informational:
Calhoun et al. Expires August 2003 [Page 23]
INTERNET-DRAFT Diameter NAS Application Feb 2003
1 Login
2 Framed
3 Callback Login
4 Callback Framed
5 Outbound
6 Administrative
7 NAS Prompt
8 Authenticate Only
9 Callback NAS Prompt
10 Call Check
11 Callback Administrative
12 Voice
13 Fax
14 Modem Relay
The following values are further qualified:
Login 1
The user should be connected to a host. The message MAY include
additional AVPs defined in sections 6.15 or 6.16.
Framed 2
A Framed Protocol should be started for the User, such as PPP
or SLIP. The message MAY include additional AVPs defined in
sections 6.9, or 7 for tunneling services.
Callback Login 3
The user should be disconnected and called back, then connected
to a host. The message MAY include additional AVPs defined in
this section.
Callback Framed 4
The user should be disconnected and called back, then a Framed
Protocol should be started for the User, such as PPP or SLIP.
The message MAY include additional AVPs defined in sections
6.9, or 7 for tunneling services.
6.2. Callback-Number AVP
The Callback-Number AVP (AVP Code 19) is of type UTF8String, and
contains a dialing string to be used for callback. It MAY be used in
an authentication and/or authorization request as a hint to the
server that a Callback service is desired, but the server is not
required to honor the hint in the corresponding response.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
Calhoun et al. Expires August 2003 [Page 24]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.3. Callback-Id AVP
The Callback-Id AVP (AVP Code 20) is of type UTF8String, and contains
the name of a place to be called, to be interpreted by the NAS. This
AVP MAY be present in an authentication and/or authorization
response.
This AVP is not roaming-friendly since it assumes that the Callback-
Id is configured on the NAS. It is therefore preferable to use the
Callback-Number AVP instead.
6.4. Idle-Timeout AVP
The Idle-Timeout AVP (AVP Code 28) is of type Unsigned32 and sets the
maximum number of consecutive seconds of idle connection allowed to
the user before termination of the session or prompt. It MAY be used
in an authentication and/or authorization request (or challenge) as a
hint to the server that an idle timeout is desired, but the server is
not required to honor the hint in the corresponding response.
6.5. Port-Limit AVP
The Port-Limit AVP (AVP Code 62) is of type Unsigned32 and sets the
maximum number of ports to be provided to the user by the NAS. It
MAY be used in an authentication and/or authorization request as a
hint to the server that multilink PPP [PPPMP] service is desired, but
the server is not required to honor the hint in the corresponding
response.
6.6. NAS-Filter-Rule AVP
The NAS-Filter-Rule AVP (AVP Code 400) is of type IPFilterRule, and
provides filter rules that need to be configured on the NAS for the
user. One or more such AVPs MAY be present in an authorization
response.
6.7. Filter-Id AVP
The Filter-Id AVP (AVP Code 11) is of type UTF8String, and contains
the name of the filter list for this user. Zero or more Filter-Id
AVPs MAY be sent in an authorization answer.
Identifying a filter list by name allows the filter to be used on
Calhoun et al. Expires August 2003 [Page 25]
INTERNET-DRAFT Diameter NAS Application Feb 2003
different NASes without regard to filter-list implementation details.
However, this AVP is not roaming friendly since filter naming differs
from one service provider to another.
In non-RADIUS environments, it is RECOMMENDED that the NAS-Filter-
Rule AVP be used instead.
6.8. Configuration-Token AVP
The Configuration-Token AVP (AVP Code 78) is of type OctetString and
is sent by a Diameter Server to a Diameter Proxy Agent or Translation
Agent in an AA-Answer command to indicate a type of user profile to
be used. It should not be sent to a Diameter Client (NAS).
The format of the Data field of this AVP is site specific.
6.9. Framed Access Authorization AVPs
This section contains the authorization AVPs that are necessary to
support framed access, such as PPP, SLIP, etc. AVPs defined in this
section MAY be present in a message if the Service-Type AVP was set
to "Framed" or "Callback Framed".
6.9.1. Framed-Protocol AVP
The Framed-Protocol AVP (AVP Code 7) is of type Enumerated and
contains the framing to be used for framed access. This AVP MAY be
present in both requests and responses. The supported values are
listed in [RADIUSTypes]. The following list is informational:
1 PPP
2 SLIP
3 AppleTalk Remote Access Protocol (ARAP)
4 Gandalf proprietary SingleLink/MultiLink protocol
5 Xylogics proprietary IPX/SLIP
6 X.75 Synchronous
6.9.2. Framed-Routing AVP
The Framed-Routing AVP (AVP Code 10) is of type Enumerated and
contains the routing method for the user, when the user is a router
to a network. This AVP SHOULD only be present in authorization
Calhoun et al. Expires August 2003 [Page 26]
INTERNET-DRAFT Diameter NAS Application Feb 2003
responses. The supported values are listed in [RADIUSTypes]. The
following list is informational:
0 None
1 Send routing packets
2 Listen for routing packets
3 Send and Listen
6.9.3. Framed-MTU AVP
The Framed-MTU AVP (AVP Code 12) is of type Unsigned32 and contains
the Maximum Transmission Unit to be configured for the user, when it
is not negotiated by some other means (such as PPP). This AVP SHOULD
only be present in authorization responses. The MTU value MUST be in
the range of 64 and 65535.
6.9.4. Framed-Compression AVP
The Framed-Compression AVP (AVP Code 13) is of type Enumerated and
contains the compression protocol to be used for the link. It MAY be
used in an authorization request as a hint to the server that a
specific compression type is desired, but the server is not required
to honor the hint in the corresponding response.
More than one compression protocol AVP MAY be sent. It is the
responsibility of the NAS to apply the proper compression protocol to
appropriate link traffic.
The supported values are listed in [RADIUSTypes]. The following list
is informational:
0 None
1 VJ TCP/IP header compression
2 IPX header compression
3 Stac-LZS compression
6.10. IP Access
The AVPs defined in this section are used when the user requests, or
is being granted, access to IP. They are only present if the Framed-
Protocol AVP (see Section 6.9.1) is set to PPP, SLIP, Gandalf
proprietarySingleLink/MultiLink protocol, or X.75 Synchronous.
Calhoun et al. Expires August 2003 [Page 27]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.10.1. Framed-IP-Address AVP
The Framed-IP-Address AVP (AVP Code 8) [RADIUS] is of type
OctetString and contains an IPv4 address, of the type specified in
the attribute value, to be configured for the user. It MAY be used in
an authorization request as a hint to the server that a specific
address is desired, but the server is not required to honor the hint
in the corresponding response.
Two IPv4 addresses have special significance; 0xFFFFFFFF and
0xFFFFFFFE. The value 0xFFFFFFFF indicates that the NAS should allow
the user to select an address (e.g. Negotiated). The value 0xFFFFFFFE
indicates that the NAS should select an address for the user (e.g.
Assigned from a pool of addresses kept by the NAS).
6.10.2. Framed-IP-Netmask AVP
The Framed-IP-Netmask AVP (AVP Code 9) is of type OctetString and
contains the four octets of the IPv4 netmask to be configured for the
user when the user is a router to a network. It MAY be used in an
authorization request as a hint to the server that a specific netmask
is desired, but the server is not required to honor the hint in the
corresponding response. This AVP MUST be present in a response if the
request included this AVP with a value of 0xFFFFFFFF.
6.10.3. Framed-Route AVP
The Framed-Route AVP (AVP Code 22) is of type UTF8String, and
contains the ASCII routing information to be configured for the user
on the NAS. Zero or more such AVPs MAY be present in an authorization
response.
The string MUST contain a destination prefix in dotted quad form
optionally followed by a slash and a decimal length specifier stating
how many high order bits of the prefix should be used. That is
followed by a space, a gateway address in dotted quad form, a space,
and one or more metrics separated by spaces. For example,
"192.168.1.0/24 192.168.1.1 1".
The length specifier may be omitted in which case it should default
to 8 bits for class A prefixes, 16 bits for class B prefixes, and 24
bits for class C prefixes. For example, "192.168.1.0 192.168.1.1 1".
Whenever the gateway address is specified as "0.0.0.0" the IP address
of the user SHOULD be used as the gateway address.
Calhoun et al. Expires August 2003 [Page 28]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.10.4. Framed-Pool AVP
The Framed-Pool AVP (AVP Code 88) is of type OctetString and contains
the name of an assigned address pool that SHOULD be used to assign an
address for the user. If a NAS does not support multiple address
pools, the NAS SHOULD ignore this AVP. Address pools are usually
used for IP addresses, but can be used for other protocols if the NAS
supports pools for those protocols.
Although specified as type OctetString for compatibility with RADIUS
[RADIUSExt], the encoding of the Data field SHOULD also conform to
the rules for the UTF8String Data Format.
6.10.5. Framed-Interface-Id AVP
The Framed-Interface-Id AVP (AVP Code 96) is of type Unsigned64 and
contains the IPv6 interface identifier to be configured for the user.
It MAY be used in authorization requests as a hint to the server that
a specific interface id is desired, but the server is not required to
honor the hint in the corresponding response.
6.10.6. Framed-IPv6-Prefix AVP
The Framed-IPv6-Prefix AVP (AVP Code 97) is of type OctetString and
contains the IPv6 prefix to be configured for the user. One or more
AVPs MAY be used in authorization requests as a hint to the server
that a specific IPv6 prefixes are desired, but the server is not
required to honor the hint in the corresponding response.
6.10.7. Framed-IPv6-Route AVP
The Framed-IPv6-Route AVP (AVP Code 99) is of type UTF8String, and
contains the ASCII routing information to be configured for the user
on the NAS. Zero or more such AVPs MAY be present in an authorization
response.
The string MUST contain an IPv6 address prefix followed by a slash
and a decimal length specifier stating how many high order bits of
the prefix should be used. That is followed by a space, a gateway
address in hexadecimal notation, a space, and one or more metrics
separated by spaces. For example:
"2000:0:0:106::/64 2000::106:a00:20ff:fe99:a998 1".
Whenever the gateway address is the IPv6 unspecified address the IP
address of the user SHOULD be used as the gateway address, such as:
Calhoun et al. Expires August 2003 [Page 29]
INTERNET-DRAFT Diameter NAS Application Feb 2003
"2000:0:0:106::/64 :: 1".
6.10.8. Framed-IPv6-Pool AVP
The Framed-IPv6-Pool AVP (AVP Code 100) is of type OctetString, and
contains the name of an assigned pool that SHOULD be used to assign
an IPv6 prefix for the user. If the access device does not support
multiple prefix pools, it MUST ignore this AVP.
Although specified as type OctetString for compatibility with RADIUS
[RADIUSIPv6], the encoding of the Data field SHOULD also conform to
the rules for the UTF8String Data Format.
6.11. IPX Access
The AVPs defined in this section are used when the user requests, or
is being granted, access to IPX. They are only present if the Framed-
Protocol AVP (see Section 6.9.1) is set to PPP, Xylogics proprietary
IPX/SLIP, Gandalf proprietarySingleLink/MultiLink protocol, or X.75
Synchronous.
6.11.1. Framed-IPX-Network AVP
The Framed-IPX-Network AVP (AVP Code 23) is of type UTF8String, and
contains the IPX Network number to be configured for the user. It MAY
be used in an authorization request as a hint to the server that a
specific address is desired, but the server is not required to honor
the hint in the corresponding response.
Two addresses have special significance; 0xFFFFFFFF and 0xFFFFFFFE.
The value 0xFFFFFFFF indicates that the NAS should allow the user to
select an address (e.g. Negotiated). The value 0xFFFFFFFE indicates
that the NAS should select an address for the user (e.g. assigned
from a pool of one or more IPX networks kept by the NAS).
6.12. Appletalk Access
The AVPs defined in this section are used when the user requests, or
is being granted, access to Appletalk. They are only present if the
Framed-Protocol AVP (see Section 6.9.1) is set to PPP, Gandalf
proprietary, SingleLink/MultiLink protocol, or X.75 Synchronous.
Calhoun et al. Expires August 2003 [Page 30]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.12.1. Framed-AppleTalk-Link AVP
The Framed-AppleTalk-Link AVP (AVP Code 37) is of type Unsigned32 and
contains the AppleTalk network number which should be used for the
serial link to the user, which is another AppleTalk router. This AVP
MUST only be present in an authorization response and is never used
when the user is not another router.
Despite the size of the field, values range from zero to 65535. The
special value of zero indicates that this is an unnumbered serial
link. A value of one to 65535 means that the serial line between the
NAS and the user should be assigned that value as an AppleTalk
network number.
6.12.2. Framed-AppleTalk-Network AVP
The Framed-AppleTalk-Network AVP (AVP Code 38) is of type Unsigned32
and contains the AppleTalk Network number which the NAS should probe
to allocate an AppleTalk node for the user. This AVP MUST only be
present in an authorization response and is never used when the user
is not another router. Multiple instances of this AVP indicate that
the NAS may probe using any of the network numbers specified.
Despite the size of the field, values range from zero to 65535. The
special value zero indicates that the NAS should assign a network for
the user, using its default cable range. A value between one and
65535 (inclusive) indicates the AppleTalk Network the NAS should
probe to find an address for the user.
6.12.3. Framed-AppleTalk-Zone AVP
The Framed-AppleTalk-Zone AVP (AVP Code 39) is of type OctetString
and contains the AppleTalk Default Zone to be used for this user.
This AVP MUST only be present in an authorization response. Multiple
instances of this AVP in the same message are not allowed.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
6.13. ARAP Access
The AVPs defined in this section are used when the user requests, or
is being granted, access to ARAP. They are only present if the
Framed-Protocol AVP (see Section 6.9.1) is set to AppleTalk Remote
Access Protocol (ARAP).
Calhoun et al. Expires August 2003 [Page 31]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.13.1. ARAP-Features AVP
The ARAP-Features AVP (AVP Code 71) is of type OctetString, and MAY
be present in the AA-Accept message if the Framed-Protocol AVP is set
to the value of ARAP. See [RADIUSExt] for more information of the
format of this AVP.
6.13.2. ARAP-Zone-Access AVP
The ARAP-Zone-Access AVP (AVP Code 72) is of type Enumerated, and MAY
be present in the AA-Accept message if the Framed-Protocol AVP is set
to the value of ARAP.
The supported values are listed in [RADIUSTypes], and are defined in
[RADIUSExt].
6.14. Non-Framed Access Authorization AVPs
This section contains the authorization AVPs that are needed to
support terminal server functionality. AVPs defined in this section
MAY be present in a message if the Service-Type AVP was set to
"Login" or "Callback Login".
6.14.1. Login-IP-Host AVP
The Login-IP-Host AVP (AVP Code 14) [RADIUS] is of type OctetString
and contains the IPv4 address of a host with which to connect the
user when the Login-Service AVP is included. It MAY be used in an
AA-Request command as a hint to the Diameter Server that a specific
host is desired, but the Diameter Server is not required to honor the
hint in the AA-Answer.
Two addresses have special significance: All ones and 0. The value
of all ones indicates that the NAS SHOULD allow the user to select an
address. The value 0 indicates that the NAS SHOULD select a host to
connect the user to.
6.14.2. Login-IPv6-Host AVP
The Login-IPv6-Host AVP (AVP Code 98) [RADIUSIPv6] is of type
OctetString and contains the IPv6 address of a host with which to
connect the user when the Login-Service AVP is included. It MAY be
used in an AA-Request command as a hint to the Diameter Server that a
specific host is desired, but the Diameter Server is not required to
Calhoun et al. Expires August 2003 [Page 32]
INTERNET-DRAFT Diameter NAS Application Feb 2003
honor the hint in the AA-Answer.
Two addresses have special significance:
0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF and 0. The value
0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF indicates that the NAS SHOULD
allow the user to select an address. The value 0 indicates that the
NAS SHOULD select a host to connect the user to.
6.14.3. Login-Service AVP
The Login-Service AVP (AVP Code 15) is of type Enumerated and
contains the service which should be used to connect the user to the
login host. This AVP SHOULD only be present in authorization
responses.
The supported values are listed in [RADIUSTypes]. The following list
is informational:
0 Telnet
1 Rlogin
2 TCP Clear
3 PortMaster (proprietary)
4 LAT
5 X25-PAD
6 X25-T3POS
8 TCP Clear Quiet (suppresses any NAS-generated connect
string)
6.15. TCP Services
The AVPs described in this section MAY be present if the Login-
Service AVP is set to Telnet, Rlogin, TCP Clear or TCP Clear Quiet.
6.15.1. Login-TCP-Port AVP
The Login-TCP-Port AVP (AVP Code 16) is of type Unsigned32 and
contains the TCP port with which the user is to be connected, when
the Login-Service AVP is also present. This AVP SHOULD only be
present in authorization responses. The value MUST NOT be greater
than 65535.
Calhoun et al. Expires August 2003 [Page 33]
INTERNET-DRAFT Diameter NAS Application Feb 2003
6.15.2. LAT Services
The AVP described in this section MAY be present if the Login-Service
AVP is set to LAT.
6.15.3. Login-LAT-Service AVP
The Login-LAT-Service AVP (AVP Code 34) is of type OctetString and
contains the system with which the user is to be connected by LAT. It
MAY be used in an authorization request as a hint to the server that
a specific service is desired, but the server is not required to
honor the hint in the corresponding response. This AVP MUST only be
present in the response if the Login-Service AVP states that LAT is
desired.
Administrators use the service attribute when dealing with clustered
systems, such as a VAX or Alpha cluster. In such an environment
several different time sharing hosts share the same resources (disks,
printers, etc.), and administrators often configure each to offer
access (service) to each of the shared resources. In this case, each
host in the cluster advertises its services through LAT broadcasts.
Sophisticated users often know which service providers (machines) are
faster and tend to use a node name when initiating a LAT connection.
Alternately, some administrators want particular users to use certain
machines as a primitive form of load balancing (although LAT knows
how to do load balancing itself).
The String field contains the identity of the LAT service to use.
The LAT Architecture allows this string to contain $ (dollar), -
(hyphen), . (period), _ (underscore), numerics, upper and lower case
alphabetics, and the ISO Latin-1 character set extension [ISOLatin].
All LAT string comparisons are case insensitive.
6.15.4. Login-LAT-Node AVP
The Login-LAT-Node AVP (AVP Code 35) is of type OctetString and
contains the Node with which the user is to be automatically
connected by LAT. It MAY be used in an authorization request as a
hint to the server that a specific LAT node is desired, but the
server is not required to honor the hint in the corresponding
response. This AVP MUST only be present in a response if the Service-
Type AVP is set to LAT.
The String field contains the identity of the LAT service to use.
The LAT Architecture allows this string to contain $ (dollar), -
Calhoun et al. Expires August 2003 [Page 34]
INTERNET-DRAFT Diameter NAS Application Feb 2003
(hyphen), . (period), _ (underscore), numerics, upper and lower case
alphabetics, and the ISO Latin-1 character set extension [ISOLatin].
All LAT string comparisons are case insensitive.
6.15.5. Login-LAT-Group AVP
The Login-LAT-Group AVP (AVP Code 36) is of type OctetString and
contains a string identifying the LAT group codes which this user is
authorized to use. It MAY be used in an authorization request as a
hint to the server that a specific group is desired, but the server
is not required to honor the hint in the corresponding response. This
AVP MUST only be present in a response if the Service-Type AVP is set
to LAT.
LAT supports 256 different group codes, which LAT uses as a form of
access rights. LAT encodes the group codes as a 256 bit bitmap.
Administrators can assign one or more of the group code bits at the
LAT service provider; it will only accept LAT connections that have
these group codes set in the bit map. The administrators assign a
bitmap of authorized group codes to each user; LAT gets these from
the operating system, and uses these in its requests to the service
providers.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
6.15.6. Login-LAT-Port AVP
The Login-LAT-Port AVP (AVP Code 63) is of type OctetString and
contains the Port with which the user is to be connected by LAT. It
MAY be used in an authorization request as a hint to the server that
a specific port is desired, but the server is not required to honor
the hint in the corresponding response. This AVP MUST only be present
in a response if the Service-Type AVP is set to LAT.
The String field contains the identity of the LAT service to use.
The LAT Architecture allows this string to contain $ (dollar), -
(hyphen), . (period), _ (underscore), numerics, upper and lower case
alphabetics, and the ISO Latin-1 character set extension [ISOLatin].
All LAT string comparisons are case insensitive.
Calhoun et al. Expires August 2003 [Page 35]
INTERNET-DRAFT Diameter NAS Application Feb 2003
7. Tunneling Group AVPs
The Tunneling AVP (AVP Code 401) is of type Grouped and contains the
following AVPs used to describe a compulsory tunnel service
[RADTunnels],[RADTunlAcct]. Its Data field has the following ABNF
grammar:
Tunneling ::= < AVP Header: 401 >
{ Tunnel-Type }
{ Tunnel-Medium-Type }
{ Tunnel-Client-Endpoint }
{ Tunnel-Server-Endpoint }
[ Tunnel-Preference ]
[ Tunnel-Client-Auth-Id ]
[ Tunnel-Server-Auth-Id ]
[ Tunnel-Assignment-Id ]
[ Tunnel-Password ]
[ Tunnel-Private-Group-Id ]
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
AVP Section | | |SHLD| MUST| |
Attribute Name Code Defined Value Type |MUST| MAY | NOT| NOT |Encr|
-----------------------------------------|----+-----+----+-----|----|
Tunneling 401 7.0 Grouped | M | P | | V | N |
Tunnel-Type 64 7.1 Enumerated | M | P | | V | Y |
Tunnel-Medium- 65 7.2 Enumerated | M | P | | V | Y |
Type | | | | | |
Tunnel-Client- 66 7.3 UTF8String | M | P | | V | Y |
Endpoint | | | | | |
Tunnel-Server- 67 7.4 UTF8String | M | P | | V | Y |
Endpoint | | | | | |
Tunnel-Password 69 7.5 OctetString| M | P | | V | Y |
Tunnel-Private- 81 7.6 UTF8String | M | P | | V | Y |
Group-Id | | | | | |
Tunnel- 82 7.7 OctetString| M | P | | V | Y |
Assignment-Id | | | | | |
Tunnel-Preference 83 7.8 Unsigned32 | M | P | | V | Y |
Tunnel-Client- 90 7.9 Unsigned32 | M | P | | V | Y |
Auth-Id | | | | | |
Tunnel-Server- 91 7.10 OctetString| M | P | | V | Y |
Auth-Id | | | | | |
-----------------------------------------|----+-----+----+-----|----|
Calhoun et al. Expires August 2003 [Page 36]
INTERNET-DRAFT Diameter NAS Application Feb 2003
7.1. Tunnel-Type AVP
The Tunnel-Type AVP (AVP Code 64) is of type Enumerated and contains
the tunneling protocol(s) to be used (in the case of a tunnel
initiator) or the tunneling protocol in use (in the case of a tunnel
terminator). It MAY be used in an authorization request as a hint to
the server that a specific tunnel type is desired, but the server is
not required to honor the hint in the corresponding response.
The Tunnel-Type AVP SHOULD also be included in Accounting-Request
messages.
A tunnel initiator is not required to implement any of these tunnel
types; if a tunnel initiator receives a response that contains only
unknown or unsupported Tunnel-Types, the tunnel initiator MUST behave
as though a response was received with the Result-Code indicating a
failure.
The supported values are listed in [RADIUSTypes]. The following list
is informational:
1 Point-to-Point Tunneling Protocol (PPTP)
2 Layer Two Forwarding (L2F)
3 Layer Two Tunneling Protocol (L2TP)
4 Ascend Tunnel Management Protocol (ATMP)
5 Virtual Tunneling Protocol (VTP)
6 IP Authentication Header in the Tunnel-mode (AH)
7 IP-in-IP Encapsulation (IP-IP)
8 Minimal IP-in-IP Encapsulation (MIN-IP-IP)
9 IP Encapsulating Security Payload in the Tunnel-mode (ESP)
10 Generic Route Encapsulation (GRE)
11 Bay Dial Virtual Services (DVS)
12 IP-in-IP Tunneling
13 Virtual LANs (VLAN)
7.2. Tunnel-Medium-Type AVP
The Tunnel-Medium-Type AVP (AVP Code 65) is of type Enumerated and
contains the transport medium to use when creating a tunnel for those
protocols (such as L2TP) that can operate over multiple transports.
It MAY be used in an authorization request as a hint to the server
that a specific medium is desired, but the server is not required to
honor the hint in the corresponding response.
The supported values are listed in [RADIUSTypes]. The following list
is informational:
Calhoun et al. Expires August 2003 [Page 37]
INTERNET-DRAFT Diameter NAS Application Feb 2003
1 IPv4 (IP version 4)
2 IPv6 (IP version 6)
3 NSAP
4 HDLC (8-bit multidrop)
5 BBN 1822
6 802 (includes all 802 media plus Ethernet "canonical
format")
7 E.163 (POTS)
8 E.164 (SMDS, Frame Relay, ATM)
9 F.69 (Telex)
10 X.121 (X.25, Frame Relay)
11 IPX
12 Appletalk
13 Decnet IV
14 Banyan Vines
15 E.164 with NSAP format subaddress
7.3. Tunnel-Client-Endpoint AVP
The Tunnel-Client-Endpoint AVP (AVP Code 66) is of type UTF8String,
and contains the address of the initiator end of the tunnel. It MAY
be used in an authorization request as a hint to the server that a
specific endpoint is desired, but the server is not required to honor
the hint in the corresponding response.
This AVP SHOULD be included in the corresponding Accounting-Request
messages, in which case it indicates the address from which the
tunnel was initiated. This AVP, along with the Tunnel-Server-Endpoint
and Session-Id AVP [Base], MAY be used to provide a globally unique
means to identify a tunnel for accounting and auditing purposes.
If Tunnel-Medium-Type is IPv4 (1), then this string is either the
fully qualified domain name (FQDN) of the tunnel client machine, or
it is a "dotted-decimal" IP address. Conformant implementations MUST
support the dotted-decimal format and SHOULD support the FQDN format
for IP addresses.
If Tunnel-Medium-Type is IPv6 (2), then this string is either the
FQDN of the tunnel client machine, or it is a text representation of
the address in either the preferred or alternate form [IPv6Addr].
Conformant implementations MUST support the preferred form and SHOULD
support both the alternate text form and the FQDN format for IPv6
addresses.
If Tunnel-Medium-Type is neither IPv4 nor IPv6, this string is a tag
referring to configuration data local to the Diameter client that
describes the interface and medium-specific address to use.
Calhoun et al. Expires August 2003 [Page 38]
INTERNET-DRAFT Diameter NAS Application Feb 2003
7.4. Tunnel-Server-Endpoint AVP
The Tunnel-Server-Endpoint AVP (AVP Code 67) is of UTF8String, and
contains the address of the server end of the tunnel. It MAY be used
in an authorization request as a hint to the server that a specific
endpoint is desired, but the server is not required to honor the hint
in the corresponding response.
This AVP SHOULD be included in the corresponding Accounting-Request
messages, in which case it indicates the address from which the
tunnel was initiated. This AVP, along with the Tunnel-Client-Endpoint
and Session-Id AVP [Base], MAY be used to provide a globally unique
means to identify a tunnel for accounting and auditing purposes.
If Tunnel-Medium-Type is IPv4 (1), then this string is either the
fully qualified domain name (FQDN) of the tunnel client machine, or
it is a "dotted-decimal" IP address. Conformant implementations MUST
support the dotted-decimal format and SHOULD support the FQDN format
for IP addresses.
If Tunnel-Medium-Type is IPv6 (2), then this string is either the
FQDN of the tunnel client machine, or it is a text representation of
the address in either the preferred or alternate form [IPv6Addr].
Conformant implementations MUST support the preferred form and SHOULD
support both the alternate text form and the FQDN format for IPv6
addresses.
If Tunnel-Medium-Type is not IPv4 or IPv6, this string is a tag
referring to configuration data local to the Diameter client that
describes the interface and medium-specific address to use.
7.5. Tunnel-Password AVP
The Tunnel-Password AVP (AVP Code 69) is of type OctetString and may
contain a password to be used to authenticate to a remote server.
The Tunnel-Password AVP contains sensitive information. This value is
not protected in the same manner as RADIUS [RADTunnels].
As required in [Base], Diameter messages are encrypted using IPsec or
TLS. The Tunnel-Password AVP SHOULD NOT be used in untrusted proxy
environments without encrypting it using end-to-end security
techniques, such as CMS Security [DiamCMS].
Calhoun et al. Expires August 2003 [Page 39]
INTERNET-DRAFT Diameter NAS Application Feb 2003
7.6. Tunnel-Private-Group-Id AVP
The Tunnel-Private-Group-Id AVP (AVP Code 81) is of type UTF8String,
and contains the group Id for a particular tunneled session. The
Tunnel-Private-Group-Id AVP MAY be included in an authorization
request if the tunnel initiator can pre-determine the group resulting
from a particular connection and SHOULD be included in the
authorization response if this tunnel session is to be treated as
belonging to a particular private group. Private groups may be used
to associate a tunneled session with a particular group of users.
For example, it MAY be used to facilitate routing of unregistered IP
addresses through a particular interface. This AVP SHOULD be
included in the Accounting-Request messages which pertain to the
tunneled session.
7.7. Tunnel-Assignment-Id AVP
The Tunnel-Assignment-Id AVP (AVP Code 82) is of type OctetString and
is used to indicate to the tunnel initiator the particular tunnel to
which a session is to be assigned. Some tunneling protocols, such as
[PPTP] and [L2TP], allow for sessions between the same two tunnel
endpoints to be multiplexed over the same tunnel and also for a given
session to utilize its own dedicated tunnel. This attribute provides
a mechanism for Diameter to be used to inform the tunnel initiator
(e.g. PAC, LAC) whether to assign the session to a multiplexed
tunnel or to a separate tunnel. Furthermore, it allows for sessions
sharing multiplexed tunnels to be assigned to different multiplexed
tunnels.
A particular tunneling implementation may assign differing
characteristics to particular tunnels. For example, different
tunnels may be assigned different QOS parameters. Such tunnels may
be used to carry either individual or multiple sessions. The Tunnel-
Assignment-Id attribute thus allows the Diameter server to indicate
that a particular session is to be assigned to a tunnel that provides
an appropriate level of service. It is expected that any QOS-related
Diameter tunneling attributes defined in the future that accompany
this attribute will be associated by the tunnel initiator with the Id
given by this attribute. In the meantime, any semantic given to a
particular Id string is a matter left to local configuration in the
tunnel initiator.
The Tunnel-Assignment-Id AVP is of significance only to Diameter and
the tunnel initiator. The Id it specifies is intended to be of only
local use to Diameter and the tunnel initiator. The Id assigned by
the tunnel initiator is not conveyed to the tunnel peer.
Calhoun et al. Expires August 2003 [Page 40]
INTERNET-DRAFT Diameter NAS Application Feb 2003
This attribute MAY be included in authorization responses. The tunnel
initiator receiving this attribute MAY choose to ignore it and assign
the session to an arbitrary multiplexed or non-multiplexed tunnel
between the desired endpoints. This AVP SHOULD also be included in
the Accounting-Request messages which pertain to the tunneled
session.
If a tunnel initiator supports the Tunnel-Assignment-Id AVP, then it
should assign a session to a tunnel in the following manner:
- If this AVP is present and a tunnel exists between the specified
endpoints with the specified Id, then the session should be
assigned to that tunnel.
- If this AVP is present and no tunnel exists between the
specified endpoints with the specified Id, then a new tunnel
should be established for the session and the specified Id
should be associated with the new tunnel.
- If this AVP is not present, then the session is assigned to an
unnamed tunnel. If an unnamed tunnel does not yet exist between
the specified endpoints then it is established and used for this
and subsequent sessions established without the Tunnel-
Assignment-Id attribute. A tunnel initiator MUST NOT assign a
session for which a Tunnel-Assignment-Id AVP was not specified
to a named tunnel (i.e. one that was initiated by a session
specifying this AVP).
Note that the same Id may be used to name different tunnels if such
tunnels are between different endpoints.
7.8. Tunnel-Preference AVP
The Tunnel-Preference AVP (AVP Code 83) is of type Unsigned32 and is
used to identify the relative preference assigned to each tunnel when
more than one set of tunneling AVPs is returned within separate
Grouped-AVP AVPs. It MAY be used in an authorization request as a
hint to the server that a specific preference is desired, but the
server is not required to honor the hint in the corresponding
response.
For example, suppose that AVPs describing two tunnels are returned by
the server, one with a Tunnel-Type of PPTP and the other with a
Tunnel-Type of L2TP. If the tunnel initiator supports only one of
the Tunnel-Types returned, it will initiate a tunnel of that type.
If, however, it supports both tunnel protocols, it SHOULD use the
value of the Tunnel-Preference AVP to decide which tunnel should be
started. The tunnel having the numerically lowest value in the Value
Calhoun et al. Expires August 2003 [Page 41]
INTERNET-DRAFT Diameter NAS Application Feb 2003
field of this AVP SHOULD be given the highest preference. The values
assigned to two or more instances of the Tunnel-Preference AVP within
a given authorization response MAY be identical. In this case, the
tunnel initiator SHOULD use locally configured metrics to decide
which set of AVPs to use.
7.9. Tunnel-Client-Auth-Id AVP
The Tunnel-Client-Auth-Id AVP (AVP Code 90) is of type Unsigned32 and
specifies the name used by the tunnel initiator during the
authentication phase of tunnel establishment. It MAY be used in an
authorization request as a hint to the server that a specific
preference is desired, but the server is not required to honor the
hint in the corresponding response. This AVP MUST be present in the
authorization response if an authentication name other than the
default is desired. This AVP SHOULD be included in the Accounting-
Request messages which pertain to the tunneled session.
7.10. Tunnel-Server-Auth-Id AVP
The Tunnel-Server-Auth-Id AVP (AVP Code 91) is of type OctetString
and specifies the name used by the tunnel terminator during the
authentication phase of tunnel establishment. It MAY be used in an
authorization request as a hint to the server that a specific
preference is desired, but the server is not required to honor the
hint in the corresponding response. This AVP MUST be present in the
authorization response if an authentication name other than the
default is desired. This AVP SHOULD be included in the the
Accounting-Request messages which pertain to the tunneled session.
8. NAS Accounting
Applications implementing this specification use Diameter Accounting
as defined in the Base [Base] with the addition of the AVPs in the
following section.
Accounting Request messages (ACR) SHOULD be sent after any
Authentication or Authorization transaction and at the end of a
Session. The Accounting-Record-Type value indicates the type of
event. All other AVPs identify the session and provide additional
information relevant to the event.
If Authentication and Authorization are contained in one message
(typical case), then one START_RECORD should be sent. If
Calhoun et al. Expires August 2003 [Page 42]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Authentication and Authorization occur in seperate transactions, the
first message should generate a START_RECORD, and the later, an
INTERIM_RECORD. For a given session, there should only be one set of
matching START and STOP records, with any number of INTERIM_RECORDS
in between, or one EVENT_RECORD.
The following table describes the AVPs, their AVP Code values, types,
possible flag values and whether the AVP MAY be encrypted.
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
AVP Section | | |SHLD| MUST| |
Attribute Name Code Defined Value Type |MUST| MAY | NOT| NOT|Encr|
-----------------------------------------|----+-----+----+-----|----|
Accounting- 363 8.1 Unsigned64 | M | P | | V | Y |
Input-Octets | | | | | |
Accounting- 364 8.2 Unsigned64 | M | P | | V | Y |
Output-Octets | | | | | |
Accounting- 365 8.3 Unsigned64 | M | P | | V | Y |
Input-Packets | | | | | |
Accounting- 366 8.4 Unsigned64 | M | P | | V | Y |
Output-Packets | | | | | |
Acct-Session-Time 46 8.5 Unsigned32 | M | P | | V | Y |
Acct-Authentic 45 8.6 Enumerated | M | P | | V | Y |
Acct-Delay-Time 41 8.7 Unsigned32 | M | P | | V | Y |
Acct-Link-Count 51 8.8 Unsigned32 | M | P | | V | Y |
Acct-Tunnel- 68 8.9 OctetString| M | P | | V | Y |
Connection | | | | | |
Acct-Tunnel- 86 8.10 Unsigned32 | M | P | | V | Y |
Packets-Lost | | | | | |
-----------------------------------------|----+-----+----+-----|----|
8.1. Accounting-Input-Octets AVP
The Accounting-Input-Octets AVP (AVP Code 363) is of type Unsigned64,
and contains the number of octets received from the user.
For NAS usage, this AVP indicates how many octets have been received
from the port in the course of this session and can only be present
in ACR messages with an Accounting-Record-Type of INTERIM_RECORD or
STOP_RECORD.
Calhoun et al. Expires August 2003 [Page 43]
INTERNET-DRAFT Diameter NAS Application Feb 2003
8.2. Accounting-Output-Octets AVP
The Accounting-Output-Octets AVP (AVP Code 364) is of type
Unsigned64, and contains the number of octets sent to the user.
For NAS usage, this AVP indicates how many octets have been sent to
the port in the course of this session and can only be present in ACR
messages with an Accounting-Record-Type of INTERIM_RECORD or
STOP_RECORD.
8.3. Accounting-Input-Packets AVP
The Accounting-Input-Packets (AVP Code 365) is of type Unsigned64,
and contains the number of packets received from the user.
For NAS usage, this AVP indicates how many packets have been received
from the port over the course of a session being provided to a Framed
User and can only be present in ACR messages with an Accounting-
Record-Type of INTERIM_RECORD or STOP_RECORD.
8.4. Accounting-Output-Packets AVP
The Accounting-Output-Packets (AVP Code 366) is of type Unsigned64,
and contains the number of IP packets sent to the user.
For NAS usage, this AVP indicates how many packets have been sent to
the port over the course of a session being provided to a Framed User
and can only be present in ACR messages with an Accounting-Record-
Type of INTERIM_RECORD or STOP_RECORD.
8.5. Acct-Session-Time AVP
The Acct-Session-Time AVP (AVP Code 46) is of type Unsigned32, and
indicates the length of the current session in seconds. It can only
be present in ACR messages with an Accounting-Record-Type of
INTERIM_RECORD or STOP_RECORD.
8.6. Acct-Authentic AVP
The Acct-Authentic AVP (AVP Code 45) is of type Enumerated, and
specifies how the user was authenticated. The supported values are
listed in [RADIUSTypes]. The following list is informational:
1 RADIUS
Calhoun et al. Expires August 2003 [Page 44]
INTERNET-DRAFT Diameter NAS Application Feb 2003
2 Local
3 Remote
4 Diameter
8.7. Acct-Delay-Time
The Acct-Delay-Time AVP (AVP Code 41) is of type Unsigned32 and
indicates the number of seconds during which the Diameter client has
been trying to send the Accounting-Request (ACR) which contains it.
The accounting server may subtract this value from the time the ACR
arrives at the server to calculate the approximate time of the event
that caused the ACR to be generated.
This AVP is not used for retransmissions at the transport level (TCP
or SCTP). Rather, it may be used when an ACR command cannot be
transmitted because there is no appropriate peer to transmit it to or
was rejected because it could not be delivered to its destination.
In these cases, the command MAY be buffered and transmitted some time
later when an appropriate peer-connection is available or after
sufficient time has passed that the destination-host may be reachable
and operational. If the ACR is resent in this way the Acct-Delay-
Time AVP SHOULD be included. The value of this AVP indicates the
number of seconds that elapsed between the time of the first attempt
at transmission and the current attempt at transmission.
8.8. Acct-Link-Count
The Acct-Link-Count AVP (AVP Code 51) is of type Unsigned32 and
indicates the total number of links that have been active (current or
closed) in a given multilink session, at the time the accounting
record is generated. This AVP MAY be included in Accounting-Requests
for any session which may be part of a multilink service.
The Acct-Link-Count AVP may be used to make it easier for an
accounting server to know when it has all the records for a given
multilink service. When the number of Accounting-Requests received
with Accounting-Record-Type = STOP_RECORD and the same Acct-Multi-
Session-Id and unique Session-Id's equals the largest value of Acct-
Link-Count seen in those Accounting-Requests, all STOP_RECORD
Accounting-Requests for that multilink service have been received.
The following example showing eight Accounting-Requests illustrates
how the Acct-Link-Count AVP is used. In the table below, only the
relevant AVPs are shown although additional AVPs containing
accounting information will also be present in the Accounting-
Requests.
Calhoun et al. Expires August 2003 [Page 45]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Acct-Multi- Accounting- Acct-
Session-Id Session-Id Record-Type Link-Count
--------------------------------------------------------
"...10" "...10" START_RECORD 1
"...10" "...11" START_RECORD 2
"...10" "...11" STOP_RECORD 2
"...10" "...12" START_RECORD 3
"...10" "...13" START_RECORD 4
"...10" "...12" STOP_RECORD 4
"...10" "...13" STOP_RECORD 4
"...10" "...10" STOP_RECORD 4
8.9. Acct-Tunnel-Connection AVP
The Acct-Tunnel-Connection AVP (AVP Code 68) is of type OctetString,
and contains the identifier assigned to the tunnel session. This AVP,
along with the Tunnel-Client-Endpoint and Tunnel-Server-Endpoint
AVPs, may be used to provide a means to uniquely identify a tunnel
session for auditing purposes.
The format of the identifier in this AVP depends upon the value of
the Tunnel-Type AVP. For example, to fully identify an L2TP tunnel
connection, the L2TP Tunnel Id and Call Id might be encoded in this
field. The exact encoding of this field is implementation dependent.
8.10. Acct-Tunnel-Packets-Lost AVP
The Acct-Tunnel-Packets-Lost AVP (AVP Code 86) is of type Unsigned32
and contains the number of packets lost on a given link.
9. RADIUS/Diameter Protocol Interactions
This section describes some basic guidelines that may be used by
servers that act as AAA Translation Agents. A complete description of
all the differences between RADIUS and Diameter is beyond the scope
of this section and document. Note that this document does not
restrict implementations from creating additional methods, as long as
the translation function doesn't violate the RADIUS or the Diameter
protocols.
Calhoun et al. Expires August 2003 [Page 46]
INTERNET-DRAFT Diameter NAS Application Feb 2003
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
AVP Section | | |SHLD| MUST| |
Attribute Name Code Defined Value Type |MUST| MAY | NOT| NOT|Encr|
-----------------------------------------|----+-----+----+-----|----|
NAS-Identifier 32 9.2.1 UTF8String | M | P | | V | Y |
NAS-IP-Address 4 9.2.2 OctetString| M | P | | V | Y |
NAS-IPv6-Address 95 9.2.3 OctetString| M | P | | V | Y |
State 24 9.2.4 OctetString| M | P | | V | Y |
Termination- 295 9.2.5 Enumerated | M | P | | V | Y |
Cause | | | | | |
-----------------------------------------|----+-----+----+-----|----|
There are primarily two different situations that must be handled;
one where a RADIUS request is received that must be forwarded as a
Diameter request, and the inverse. RADIUS does not support a peer-
to-peer architecture and server initiated operations are generally
not supported. See [RADDynAuth] for an alternative.
Some RADIUS attributes are encrypted. RADIUS security and encryption
techniques are applied on a hop-per-hop basis. A Diameter agent will
have to decrypt RADIUS attribute data entering the Diameter system
and if that information is forwarded, MUST secure it using Diameter
specific techniques.
Note that this section uses the two terms; AVP and attribute in a
consise manner. The former is used to signify a Diameter AVP, while
the latter is used to signify a RADIUS attribute.
9.1. RADIUS Request Forwarded as Diameter Request
This section describes the actions that should be followed when a
Translation Agent receives a RADIUS message that is to be translated
to a Diameter message.
It is important to note that RADIUS servers are assumed to be
stateless, and this section maintains that assumption. It is also
quite possible for the RADIUS messages that comprise the session
(i.e. authentication and accounting messages) will be handled by
different Translation Agents in the proxy network. Therefore, a
RADIUS/Diameter Translation Agent SHOULD NOT assume to track session
state information.
When a Translation Agent receives a RADIUS message, the following
steps should be taken:
Calhoun et al. Expires August 2003 [Page 47]
INTERNET-DRAFT Diameter NAS Application Feb 2003
- If a Message-Authenticator attribute is present, it MUST be
checked and discarded. The gateway system SHOULD generate and
include a Message-Authenticator in return responses to this
system.
- The transport address of the sender MUST be checked against the
NAS identifying attributes. See the description of NAS-
Identifier and NAS-IP-Address below.
- The Diameter Origin-Host and Origin-Realm AVPs MUST be created
and added using the information from the NAS-Identifier
attribute, and/or the FQDN corresponding to the NAS-IP-Address
attribute. The AAA protocol specified in the identity would be
set to "RADIUS".
- The Proxy-Info group SHOULD be added with the local server's
identity being specified in the Proxy-Host AVP. This should
ensure that the response is returned to this system.
- The Destination-Realm AVP is created from the information found
in the RADIUS User-Name attribute.
- The Translation Agent must maintain transaction state
information relevant to the RADIUS request, such as the
Identifier field in the RADIUS header, any existing RADIUS
Proxy-State attribute as well as the source IP address and port
number of the UDP packet. These may be maintained locally in a
state table, or may be saved in a Proxy-Info AVP group.
- If the RADIUS request contained a State attribute, and the
prefix of the data is "Diameter/", the data following the prefix
contains the Diameter Session-Id. If no such attributes are
present, and the RADIUS command is an Access-Request, a new
Session-Id is created. The Session-Id is included in the
Session-Id AVP.
- If the RADIUS User-Password attribute is present, the password
must be unencrypted using the link's RADIUS shared secret. And
forwarded using Diameter security.
- If the RADIUS CHAP-Password attribute is present, the Ident and
Data portion of the attribute are used to create the CHAP-Auth
grouped AVP.
- If the RADIUS message contains an address attribute, (e.g.
Framed-IP-Address, Login-IP-Host, Login-IPv6-Host, NAS-IP-
Address, NAS-IPv6-Address) it MUST be converted to the
appropriate Diameter AVP and Address type.
- If the RADIUS message contains Tunnel information [RADTunnels],
the attributes or tagged groups should each be converted to a
Diameter Tunneling Grouped AVP set. If the tunnel information
contains a Tunnel-Password attribute, the RADIUS encryption must
be resolved, and the password forwarded using Diameter security
methods.
- If the RADIUS message received is an Accounting-Request, the
Acct-Status-Type attribute value must be converted to a
Accounting-Record-Type AVP value. If the Acct-Status-Type
Calhoun et al. Expires August 2003 [Page 48]
INTERNET-DRAFT Diameter NAS Application Feb 2003
attribute value is STOP, the local server MUST issue a Session-
Termination-Request message once the Diameter Accounting-Answer
message has been received.
- If the Accounting message contains a Acct-Termination-Cause
attribute, it should be translated to the equivalent
Termination-Cause AVP value. (see below)
- If the RADIUS message contains the Accounting-Input-Octets,
Accounting-Input-Packets, Accounting-Output-Octets or
Accounting-Output-Packets, these attributes must be converted to
the Diameter equivalent ones. Further, if the Acct-Input-
Gigawords or Acct-Output-Gigawords attributes are present, these
must be used to properly compute the Diameter accounting AVPs.
The corresponding Diameter response is always guaranteed to be
received by the same Translation Agent that translated the original
request, due to the contents of the Origin-Host AVP in the Diameter
request. The following steps are applied to the response message
during the Diameter to RADIUS translation:
- If the Diameter Command-Code is set to AA-Answer and the Result-
Code AVP is set to DIAMETER_MULTI_ROUND_AUTH, the gateway must
send a RADIUS Access-Challenge with the Diameter Session-Id and
the Origin-Host AVPs encapsulated in the RADIUS State attribute,
with the prefix "Diameter/". This is necessary in order to
ensure that the Translation Agent that will receive the
subsequent RADIUS Access-Request will have access to the Session
Identifier, and be able to set the Destination-Host to the
correct value. If the Multi-Round-Time-Out AVP is present, the
value of the AVP MUST be inserted in the RADIUS Session-Timeout
AVP.
- If the Command-Code is set to AA-Answer, the Diameter Session-Id
AVP is saved in a new RADIUS Class attribute, whose format
consists of the string "Diameter/" followed by the Diameter
Session Identifier. This will ensure that the subsequent
Accounting messages, which could be received by any Translation
Agent, would have access to the original Diameter Session
Identifier.
- If a Proxy-State attribute was present in the RADIUS request,
the same attribute is added in the response. This information
may be found in the Proxy-Info AVP group, or in a local state
table.
- If state information regarding the RADIUS request was saved in a
Proxy-Info AVP or local state table, the RADIUS Identifier and
UDP IP Address and port number are extracted and used in issuing
the RADIUS reply.
Calhoun et al. Expires August 2003 [Page 49]
INTERNET-DRAFT Diameter NAS Application Feb 2003
9.1.1. Diameter Request Forwarded as RADIUS Request
When a server receives a Diameter request that is to be forwarded to
a RADIUS entity, the following steps are an example of the steps that
may be followed:
- The Origin-Host AVP's value is inserted in the NAS-Identifier
attribute.
- The following information MUST be present in the corresponding
Diameter response, and therefore MUST be saved either in a local
state table, or it MAY be encoded in a RADIUS Proxy-State
attribute:
1. Origin-Host AVP
2. Session-Id AVP
3. Proxy-Info AVP
4. Route-Record AVPs (in the proper order)
5. Any other AVP that MUST be present in the response, and
has no corresponding RADIUS attribute.
- If the CHAP-Auth AVP is present, the grouped AVPs are used to
create the RADIUS CHAP-Password attribute data.
- If the User-Password AVP is present, the data should be
encrypted using RADIUS rules. Likewise for any other encrypted
attribute values.
- AVPs that are of the type Address, must be translated to the
corresponding RADIUS attribute.
- If the Accounting-Input-Octets, Accounting-Input-Packets,
Accounting-Output-Octets or Accounting-Output-Packets AVPs are
present, these must be translated to the corresponding RADIUS
attributes. Further, the value of the Diameter AVPs do not fit
within a 32-bit RADIUS attribute, the RADIUS Acct-Input-
Gigawords and Acct-Output-Gigawords must be used.
- If the RADIUS link supports the Message-Authenticator attribute
[RADIUSExt] it SHOULD be generated and added to the request.
When the corresponding response is received by the Translation Agent,
which is guaranteed in the RADIUS protocol, the following steps may
be followed:
- If the RADIUS code is set to Access-Challenge, a Diameter AA-
Answer message is created with the Result-Code set to
DIAMETER_MULTI_ROUND_AUTH. If the Session-Timeout AVP is present
in the RADIUS message, its value is inserted in the Multi-Round-
Time-Out AVP.
- If a Proxy-State attribute is present, extract the encoded
information, otherwise retrieve the original Proxy-Info AVP
group information from the local state table.
- The request's Origin-Host information is added to the
Calhoun et al. Expires August 2003 [Page 50]
INTERNET-DRAFT Diameter NAS Application Feb 2003
Destination-Host AVP.
- The Acct-Session-Id information is added to the Session-Id AVP.
- The Route-Record AVPs MUST be added to the Diameter message, in
the same order they were present in the request.
- If a Proxy-Info AVP was present in the request, the same AVP
MUST be added to the response.
- If the RADIUS State attributes are present, these attributes
must be present in the Diameter response.
- Any other AVPs that were saved, and MUST be present in the
response, are added to the message.
9.2. AVPs Used Only for Compatibility
The AVPs defined in this section SHOULD only used for backwards
compatibility when a Diameter/RADIUS translation function is invoked,
and are not typically originated by Diameter systems during normal
operations.
9.2.1. NAS-Identifier AVP
The NAS-Identifier AVP (AVP Code 32) [RADIUS] is of type UTF8String
and contains the identity of the NAS providing service to the user.
This AVP SHOULD only be added by a RADIUS/Diameter Translation Agent.
When this AVP is present, the Origin-Host AVP identifies the
RADIUS/Diameter Translation Agent rather than the NAS providing
service to the user.
In RADIUS it would be possible for a rogue NAS to forge the NAS-
Identifier attribute. Diameter/RADIUS translation agents SHOULD
attempt to check a received NAS-Identifier attribute against the
source address of the RADIUS packet, by doing an A/AAAA RR query. If
the NAS-Identifier attribute contains an FQDN, then such a query
would resolve to an IP address matching the source address. However,
the NAS-Identifier attribute is not required to contain an FQDN, so
such a query could fail. In this case, an error should be logged, but
no other action taken, other than doing a reverse lookup on the
source address and inserting the resulting FQDN into the Route-Record
AVP.
Diameter agents and servers SHOULD check whether a NAS-Identifier AVP
corresponds to an entry in the Record-Route AVP. If no match is
found, then an error is logged, but no other action is taken.
Calhoun et al. Expires August 2003 [Page 51]
INTERNET-DRAFT Diameter NAS Application Feb 2003
9.2.2. NAS-IP-Address AVP
The NAS-IP-Address AVP (AVP Code 4) [RADIUS] is of type OctetString,
and contains the IP Address of the NAS providing service to the user.
This AVP SHOULD only be added by a RADIUS/Diameter Translation Agent.
When this AVP is present, the Origin-Host AVP identifies the
RADIUS/Diameter Translation Agent rather than the NAS providing
service to the user.
In RADIUS it would be possible for a rogue NAS to forge the NAS-IP-
Address attribute value. Diameter/RADIUS translation agents MUST
check a received NAS-IP-Address or NAS-IPv6-Address attribute against
the source address of the RADIUS packet. If they do not match, and
the Diameter/RADIUS translation agent does not know whether the
packet was sent by a RADIUS proxy or NAS (e.g. no Proxy-State
attribute) then by default it is assumed that the source address
corresponds to a RADIUS proxy, and that the NAS Address is behind
that proxy, potentially with some additional RADIUS proxies in
between. The Diameter/RADIUS translation agent MUST insert entries
in the Route-Record AVP corresponding to the apparent route. This
implies doing a reverse lookup on the source address and NAS-IP-
Address, or NAS-IPv6-Address attributes in order to determine the
corresponding FQDNs.
If the source address and the NAS-IP-Address, or NAS-IPv6-Address do
not match, and the Diameter/RADIUS translation agent knows that it is
talking directly to the NAS (e.g. no RADIUS proxies between it and
the NAS), then the error should be logged, and the packet MUST be
discarded.
Diameter agents and servers MUST check whether the NAS-IP-Address AVP
corresponds to an entry in the Record-Route AVP. This is done by
doing a reverse lookup (PTR RR) for the NAS-IP-Address to retrieve
the corresponding FQDN, and checking for a match with the Record-
Route AVP. If no match is found, then an error is logged, but no
other action is taken.
9.2.3. NAS-IPv6-Address AVP
The NAS-IPv6-Address AVP (AVP Code 95) [RADIUSIPv6] is of type
OctetString, and contains the IPv6 Address of the NAS providing
service to the user. This AVP SHOULD only be added by a
RADIUS/Diameter Translation Agent. When this AVP is present, the
Origin-Host AVP identifies the RADIUS/Diameter Translation Agent
rather than the NAS providing service to the user.
In RADIUS it would be possible for a rogue NAS to forge the NAS-
Calhoun et al. Expires August 2003 [Page 52]
INTERNET-DRAFT Diameter NAS Application Feb 2003
IPv6-Address attribute. Diameter/RADIUS translation agents MUST check
a received NAS-IPv6-Address attribute against the source address of
the RADIUS packet. If they do not match, and the Diameter/RADIUS
translation agent does not know whether the packet was sent by a
RADIUS proxy or NAS (e.g. no Proxy-State attribute) then by default
it is assumed that the source address corresponds to a RADIUS proxy,
and that the NAS-IPv6-Address is behind that proxy, potentially with
some additional RADIUS proxies in between. The Diameter/RADIUS
translation agent MUST insert entries in the Route-Record AVP
corresponding to the apparent route. This implies doing a reverse
lookup on the source address and NAS-IP-Address attributes in order
to determine the corresponding FQDNs.
If the source address and the NAS-IPv6-Address do not match, and the
Diameter/RADIUS translation agent knows that it is talking directly
to the NAS (e.g. no RADIUS proxies between it and the NAS), then the
error should be logged, and the packet MUST be discarded.
Diameter agents and servers MUST check whether the NAS-IPv6-Address
AVP corresponds to an entry in the Record-Route AVP. This is done by
doing a reverse lookup (PTR RR) for the NAS-IPv6-Address to retrieve
the corresponding FQDN, and checking for a match with the Record-
Route AVP. If no match is found, then an error is logged, but no
9.2.4. State AVP
The State AVP (AVP Code 24) [RADIUS] is of type OctetString and has
two uses in the Diameter NAS application.
The State AVP MAY be sent by a Diameter Server to a NAS in an AA-
Response command that contains a Result-Code of
DIAMETER_MULTI_ROUND_AUTH. If so, the NAS MUST return it unmodified
in the subsquent AA-Request command.
The State AVP MAY also be sent by a Diameter Server to a NAS in an
AA-Response command that also includes a Termination-Action AVP with
the value of AA-REQUEST. If the NAS performs the Termination-Action
by sending a new AA-Request command upon termination of the current
service, it MUST return the State AVP unmodified in the new request
command.
In either usage the NAS MUST NOT interpret the AVP locally. Usage of
the State AVP is implementation dependent.
Calhoun et al. Expires August 2003 [Page 53]
INTERNET-DRAFT Diameter NAS Application Feb 2003
9.2.5. Termination-Cause AVP Code Values
This section defines a mapping between Termination-Cause AVP code
values and RADIUS Acct-Terminate-Cause attribute code values from RFC
2866 [RADIUSAcct] and [RADIUSTypes], thereby allowing a
RADIUS/Diameter Translation Agent to convert between the attribute
and AVP values. This section thus extends the definitions in the
"Termination-Cause AVP" section of the Base Diameter specification.
The table in this section defines the mapping between Termination-
Cause AVP and RADIUS Acct-Terminate-Cause causes.
+-----------------------+
| Value |
+-----------+-----------+
Cause Value Name | RADIUS | Diameter |
------------------------------|-----------+-----------+
User Request | 1 | 11 |
Lost Carrier | 2 | 12 |
Lost Service | 3 | 13 |
Idle Timeout | 4 | 14 |
Session Timeout | 5 | 15 |
Admin Reset | 6 | 16 |
Admin Reboot | 7 | 17 |
Port Error | 8 | 18 |
NAS Error | 9 | 19 |
NAS Request | 10 | 20 |
NAS Reboot | 11 | 21 |
Port Unneeded | 12 | 22 |
Port Preempted | 13 | 23 |
Port Suspended | 14 | 24 |
Service Unavailable | 15 | 25 |
Callback | 16 | 26 |
User Error | 17 | 27 |
Host Request | 18 | 28 |
Supplicant Restart | 19 | 29 | [RAD802.1X]
Reauthentication Failure | 20 | 30 | [RAD802.1X]
Port Reinit | 21 | 31 | [RAD802.1X]
Port Disabled | 22 | 32 | [RAD802.1X]
------------------------------|-----------+-----------+
From RFC 2866, the termination causes are as follows:
User Request User requested termination of service, for
example with LCP Terminate or by logging out.
Lost Carrier DCD was dropped on the port.
Lost Service Service can no longer be provided; for
Calhoun et al. Expires August 2003 [Page 54]
INTERNET-DRAFT Diameter NAS Application Feb 2003
example, user's connection to a host was
interrupted.
Idle Timeout Idle timer expired.
Session Timeout Maximum session length timer expired.
Admin Reset Administrator reset the port or session.
Admin Reboot Administrator is ending service on the NAS,
for example prior to rebooting the NAS.
Port Error NAS detected an error on the port which
required ending the session.
NAS Error NAS detected some error (other than on the
port) which required ending the session.
NAS Request NAS ended session for a non-error reason not
otherwise listed here.
NAS Reboot The NAS ended the session in order to reboot
non-administratively ("crash").
Port Unneeded NAS ended session because resource usage fell
below low-water mark (for example, if a
bandwidth-on-demand algorithm decided that
the port was no longer needed).
Port Preempted NAS ended session in order to allocate the
port to a higher priority use.
Port Suspended NAS ended session to suspend a virtual
session.
Service Unavailable NAS was unable to provide requested service.
Callback NAS is terminating current session in order
to perform callback for a new session.
User Error Input from user is in error, causing
termination of session.
Host Request Login Host terminated session normally.
Calhoun et al. Expires August 2003 [Page 55]
INTERNET-DRAFT Diameter NAS Application Feb 2003
9.3. Prohibited RADIUS Attributes
The following RADIUS attributes MUST NOT be transfered to a Diameter
message. Many of these are discussed in section 9.1.
Attribute Description Defined Nearest Diameter AVP
-----------------------------------------------------------------
3 CHAP-Password RFC 2865 CHAP-Auth Group
26 Vendor-Specific RFC 2865 Vendor Specific AVP
40 Acct-Status-Type RFC 2866 Accounting-Record-Type
42 Acct-Input-Octets RFC 2866 Accounting-Input-Octets
43 Acct-Output-Octets RFC 2866 Accounting-Output-Octets
47 Acct-Input-Packets RFC 2866 Accounting-Input-Packets
48 Acct-Output-Packets RFC 2866 Accounting-Output-Packets
49 Acct-Terminate-Cause RFC 2866 Termination-Cause
52 Acct-Input-Gigawords RFC 2869 Accounting-Input-Octets
53 Acct-Output-Gigawords RFC 2869 Accounting-Output-Octets
80 Message-Authenticator RFC 2869 none - check and discard
9.4. Translatable Diameter AVPs
In general, Diameter AVPs that are not RADIUS compatible have code
values greater than 255. The table in the section above shows the
AVPs that can be converted into RADIUS attributes.
Another problem may occur with Diameter AVP values that may be more
than 253 octets in length (eg: Reply-Message). Some RADIUS
attributes allow concatenation of multiple instances to overcome this
limitation. If this is not possible, an attribute error should be
returned.
9.5. RADIUS Vendor Specific Attributes
RADIUS supports the inclusion of Vendor Specific Attributes (VSAs)
through the use of attribute 26. The recommended format [RADIUS] of
the attribute data field includes a 4 octet vendor code followed by a
one octet vendor type field and a one octet length field. The last
two fields MAY be repeated.
9.5.1. Forwarding a Diameter Vendor AVP as a RADIUS VSA
The RADIUS VSA attribute should consist of the following fields;
RADIUS Type = 26, Vendor Specific Attribute
RADIUS Length = total length of attribute (header + data)
Calhoun et al. Expires August 2003 [Page 56]
INTERNET-DRAFT Diameter NAS Application Feb 2003
RADIUS Vendor code = Diameter Vendor code
RADIUS Vendor type code = low order byte of Diameter AVP code
RADIUS Vendor data length = length of Diameter data
(not including padding)
If the Diameter AVP code is greater than 255, then the RADIUS
speaking code may use a Vendor specific field coding, if it knows one
for that vendor. Otherwise, the AVP will be ignored. Unless it is
flagged as Mandatory, in which case an "DIAMETER_AVP_UNSUPPORTED"
error will be returned, and the message will not be sent.
9.5.2. Forwarding a RADIUS VSA to a Diameter Vendor AVP
The Diameter AVP will consist of the following fields;
Diameter Flags: V=1, M=0, P=0
Diameter Vendor code = RADIUS VSA Vendor code
Diameter AVP code = RADIUS VSA Vendor type code
Diameter AVP length = length of AVP (header + data + padding)
Diameter Data = RADIUS VSA vendor data
If the RADIUS receiving code knows of vendor specific fields
interpretations for the specific vendor, it may employ them to parse
an extended AVP code or data length, Otherwise the recommended
standard fields will be used.
Nested Multiple vendor data fields MUST be expanded into multiple
Diameter AVPs.
10. AVP Occurrence Tables
The following tables present the AVPs defined in this document, and
specify in which Diameter messages they MAY, or MAY NOT be present.
Note that AVPs that can only be present within a Grouped AVP are not
represented in this table.
The table uses the following symbols:
0 The AVP MUST NOT be present in the message.
0+ Zero or more instances of the AVP MAY be present in the
message.
0-1 Zero or one instance of the AVP MAY be present in the
message.
1 One instance of the AVP MUST be present in the message.
Calhoun et al. Expires August 2003 [Page 57]
INTERNET-DRAFT Diameter NAS Application Feb 2003
10.1. AA-Request/Answer AVP Table
The table in this section is limited to the Command Codes defined in
this specification.
Calhoun et al. Expires August 2003 [Page 58]
INTERNET-DRAFT Diameter NAS Application Feb 2003
+-----------+
| Command |
|-----+-----+
Attribute Name | AAR | AAA |
------------------------------|-----+-----+
Acct-Interim-Interval | 0 | 0-1 |
ARAP-Challenge-Response | 0 | 0-1 |
ARAP-Features | 0 | 0-1 |
ARAP-Password | 0-1 | 0 |
ARAP-Security | 0-1 | 0-1 |
ARAP-Security-Data | 0+ | 0+ |
ARAP-Zone-Access | 0 | 0-1 |
Auth-Application-Id | 1 | 1 |
Auth-Grace-Period | 0-1 | 0-1 |
Auth-Request-Type | 1 | 1 |
Auth-Session-State | 0-1 | 0-1 |
Authorization-Lifetime | 0-1 | 0-1 |
Callback-Id | 0 | 0-1 |
Callback-Number | 0-1 | 0-1 |
Called-Station-Id | 0-1 | 0 |
Calling-Station-Id | 0-1 | 0 |
CHAP-Auth | 0-1 | 0 |
CHAP-Challenge | 0-1 | 0 |
Class | 0+ | 0+ |
Configuration-Token | 0 | 0+ |
Connect-Info | 0-1 | 0 |
Destination-Host | 0-1 | 0 |
Destination-Realm | 1 | 0 |
Error-Message | 0 | 0-1 |
Error-Reporting-Host | 0 | 0-1 |
Failed-AVP | 0+ | 0+ |
Filter-Id | 0 | 0+ |
Framed-Appletalk-Link | 0 | 0-1 |
Framed-Appletalk-Network | 0 | 0+ |
Framed-Appletalk-Zone | 0 | 0-1 |
Framed-Compression | 0+ | 0+ |
Framed-Interface-Id | 0-1 | 0-1 |
Framed-IP-Address | 0-1 | 0-1 |
Framed-IP-Netmask | 0-1 | 0-1 |
Framed-IPv6-Prefix | 0+ | 0+ |
Framed-IPv6-Pool | 0 | 0-1 |
Framed-IPv6-Route | 0 | 0+ |
Framed-IPX-Network | 0 | 0-1 |
Framed-MTU | 0-1 | 0-1 |
Framed-Pool | 0 | 0-1 |
Framed-Protocol | 0-1 | 0-1 |
Framed-Route | 0 | 0+ |
------------------------------|-----+-----+
Calhoun et al. Expires August 2003 [Page 59]
INTERNET-DRAFT Diameter NAS Application Feb 2003
+-----------+
| Command |
|-----+-----+
Attribute Name | AAR | AAA |
------------------------------|-----+-----+
Framed-Routing | 0 | 0-1 |
Idle-Timeout | 0-1 | 0-1 |
Login-IP-Host | 0+ | 0+ |
Login-IPv6-Host | 0+ | 0+ |
Login-LAT-Group | 0-1 | 0-1 |
Login-LAT-Node | 0-1 | 0-1 |
Login-LAT-Port | 0-1 | 0-1 |
Login-LAT-Service | 0-1 | 0-1 |
Login-Service | 0 | 0-1 |
Login-TCP-Port | 0 | 0-1 |
Multi-Round-Time-Out | 0 | 0-1 |
NAS-Filter-Rule | 0 | 0+ |
NAS-Identifier | 0-1 | 0 |
NAS-IP-Address | 0-1 | 0 |
NAS-IPv6-Address | 0-1 | 0 |
NAS-Port | 0-1 | 0 |
NAS-Port-Id | 0-1 | 0 |
NAS-Port-Type | 0-1 | 0 |
Originating-Line-Info | 0-1 | 0 |
Origin-Host | 1 | 1 |
Origin-Realm | 1 | 1 |
Origin-State-Id | 0-1 | 0-1 |
Password-Retry | 0 | 0-1 |
Port-Limit | 0-1 | 0-1 |
Prompt | 0 | 0-1 |
Proxy-Info | 0+ | 0+ |
Re-Auth-Request-Type | 0 | 0-1 |
Redirect-Host | 0 | 0+ |
Redirect-Host-Usage | 0 | 0-1 |
Redirect-Max-Cache-Time | 0 | 0-1 |
Reply-Message | 0 | 0+ |
Result-Code | 0 | 1 |
Route-Record | 0+ | 0 |
Service-Type | 0-1 | 0-1 |
Session-Id | 1 | 1 |
Session-Timeout | 0-1 | 0-1 |
State | 0-1 | 0-1 |
Termination-Action | 0 | 0-1 |
Termination-Cause | 0 | 0-1 |
Tunneling | 0+ | 0+ |
User-Name | 0-1 | 0-1 |
User-Password | 0-1 | 0 |
------------------------------|-----+-----+
Calhoun et al. Expires August 2003 [Page 60]
INTERNET-DRAFT Diameter NAS Application Feb 2003
10.2. Accounting AVP Tables
The tables in this section are used to represent which AVPs defined
in this document are to be present in the Accounting messages,
defined in [Base] and [RADIUSAcct].
10.2.1. Accounting Framed Access AVP Table
The table in this section is used when the Service-Type specifies
Framed Access.
+-----------+
| Command |
|-----+-----+
Attribute Name | ACR | ACA |
---------------------------------------|-----+-----+
Accounting-Application-Id | 0-1 | 0-1 |
Accounting-Input-Octets | 1 | 0 |
Accounting-Input-Packets | 1 | 0 |
Accounting-Output-Octets | 1 | 0 |
Accounting-Output-Packets | 1 | 0 |
Accounting-Record-Type | 1 | 1 |
Accounting-Record-Number | 0-1 | 0-1 |
Accounting-Realtime-Required | 0-1 | 0 |
Accounting-Sub-Session-Id | 0-1 | 0-1 |
Acct-Application-Id | 0-1 | 0-1 |
Acct-Session-Id | 0-1 | 0-1 |
Acct-Multi-Session-Id | 0-1 | 0-1 |
Acct-Authentic | 1 | 0 |
Acct-Delay-Time | 0-1 | 0 |
Acct-Interim-Interval | 0-1 | 0 |
Acct-Link-Count | 0-1 | 0 |
Acct-Session-Time | 1 | 0 |
Acct-Tunnel-Connection | 0-1 | 0 |
Acct-Tunnel-Packets-Lost | 0-1 | 0 |
Event-Timestamp | 0-1 | 0-1 |
Error-Reporting-Host | 0 | 0-1 |
Framed-AppleTalk-Link | 0-1 | 0 |
Framed-AppleTalk-Network | 0-1 | 0 |
Framed-AppleTalk-Zone | 0-1 | 0 |
Framed-Compression | 0-1 | 0 |
---------------------------------------|-----+-----+
Calhoun et al. Expires August 2003 [Page 61]
INTERNET-DRAFT Diameter NAS Application Feb 2003
+-----------+
| Command |
|-----+-----+
Attribute Name | ACR | ACA |
---------------------------------------|-----+-----+
Framed-IP-Address | 0-1 | 0 |
Framed-IP-Netmask | 0-1 | 0 |
Framed-IPv6-Pool | 0-1 | 0 |
Framed-IPX-Network | 0-1 | 0 |
Framed-MTU | 0-1 | 0 |
Framed-Pool | 0-1 | 0 |
Framed-Protocol | 0-1 | 0 |
Framed-Route | 0-1 | 0 |
Framed-Routing | 0-1 | 0 |
NAS-Filter-Rule | 0-1 | 0 |
NAS-Identifier | 0-1 | 0-1 |
NAS-IP-Address | 0-1 | 0-1 |
NAS-IPv6-Address | 0-1 | 0-1 |
NAS-Port | 0-1 | 0-1 |
NAS-Port-Id | 0-1 | 0-1 |
NAS-Port-Type | 0-1 | 0-1 |
Origin-Host | 1 | 1 |
Origin-Realm | 1 | 1 |
Origin-State-Id | 0-1 | 0-1 |
Proxy-Info | 0+ | 0+ |
Route-Record | 0+ | 0+ |
Service-Type | 0-1 | 0-1 |
Termination-Cause | 0-1 | 0-1 |
Tunnel-Assignment-Id | 0-1 | 0 |
Tunnel-Client-Endpoint | 0-1 | 0 |
Tunnel-Medium-Type | 0-1 | 0 |
Tunnel-Private-Group-Id | 0-1 | 0 |
Tunnel-Server-Endpoint | 0-1 | 0 |
Tunnel-Type | 0-1 | 0 |
User-Name | 0-1 | 0-1 |
Vendor-Specific-Application-Id | 0-1 | 0-1 |
---------------------------------------|-----+-----+
10.2.2. Accounting Non-Framed Access AVP Table
The table in this section is used when the Service-Type specifies
Non-Framed Access.
Calhoun et al. Expires August 2003 [Page 62]
INTERNET-DRAFT Diameter NAS Application Feb 2003
+-----------+
| Command |
|-----+-----+
Attribute Name | ACR | ACA |
---------------------------------------|-----+-----+
Accounting-Application-Id | 0-1 | 0-1 |
Accounting-Input-Octets | 1 | 0 |
Accounting-Output-Octets | 1 | 0 |
Accounting-Record-Type | 1 | 1 |
Accounting-Record-Number | 0-1 | 0-1 |
Accounting-Realtime-Required | 0-1 | 0 |
Accounting-Sub-Session-Id | 0-1 | 0-1 |
Acct-Application-Id | 0-1 | 0-1 |
Acct-Session-Id | 0-1 | 0-1 |
Acct-Multi-Session-Id | 0-1 | 0-1 |
Acct-Authentic | 1 | 0 |
Acct-Delay-Time | 0-1 | 0 |
Acct-Interim-Interval | 0-1 | 0 |
Acct-Link-Count | 0-1 | 0 |
Acct-Session-Time | 1 | 0 |
Event-Timestamp | 0-1 | 0-1 |
Error-Reporting-Host | 0 | 0-1 |
Login-IP-Host | 0+ | 0 |
Login-IPv6-Host | 0+ | 0 |
Login-LAT-Service | 0-1 | 0 |
Login-LAT-Node | 0-1 | 0 |
Login-LAT-Group | 0-1 | 0 |
Login-LAT-Port | 0-1 | 0 |
Login-Service | 0-1 | 0 |
Login-TCP-Port | 0-1 | 0 |
NAS-Identifier | 0-1 | 0-1 |
NAS-IP-Address | 0-1 | 0-1 |
NAS-IPv6-Address | 0-1 | 0-1 |
NAS-Port | 0-1 | 0-1 |
NAS-Port-Id | 0-1 | 0-1 |
NAS-Port-Type | 0-1 | 0-1 |
Origin-Host | 1 | 1 |
Origin-Realm | 1 | 1 |
Origin-State-Id | 0-1 | 0-1 |
Proxy-Info | 0+ | 0+ |
Route-Record | 0+ | 0+ |
Service-Type | 0-1 | 0-1 |
Termination-Cause | 0-1 | 0-1 |
User-Name | 0-1 | 0-1 |
Vendor-Specific-Application-Id | 0-1 | 0-1 |
---------------------------------------|-----+-----+
Calhoun et al. Expires August 2003 [Page 63]
INTERNET-DRAFT Diameter NAS Application Feb 2003
11. IANA Considerations
This section provides guidance to the Internet Assigned Numbers
Authority (IANA) regarding registration of values related to the
Diameter protocol, in accordance with BCP 26 [IANAConsid].
This document defines values in the namespaces that have created and
defined in the Diameter Base [Base]. The IANA Considerations section
of that document details the assignment criteria. Values assigned in
this document, or by future IANA action, must be coordinated within
this shared namespace.
11.1. Command Codes
This specification assigns the values 265 and 268 from the Command
Code namespace defined in [Base]. See sections 3.1 and 3.2 for the
assignment of the namespace in this specification.
11.2. AVP Codes
This specification assigns the values 363-366 and 400-405 from the
AVP Code namespace defined in [Base]. See sections 4, and 5 for the
assignment of the namespace in this specification. Note that the
values 363-366 are jointly, but consistently, assigned in [DiamMIP].
This specification also specifies the use of AVPs in the 0-255 range,
which are defined in [RADIUSTypes]. These values are assigned by the
policy in RFC 2865 Section 6. [RADIUS]
11.3. Application Identifier
This specification uses the value one (1) in the Application
Identifier namespace as assigned in [Base]. See section 1.2 above
for more information.
11.4. CHAP-Algorithm AVP Values
As defined in Section 5.5, the CHAP-Algorithm AVP (AVP Code 403) uses
the values of the "PPP AUTHENTICATION ALGORITHMS" namespace defined
in [PPPCHAP].
Calhoun et al. Expires August 2003 [Page 64]
INTERNET-DRAFT Diameter NAS Application Feb 2003
12. Security Considerations
The security considerations of the Diameter protocol itself have
been discussed in [Base].
This document does not contain a security protocol, but does discuss
how PPP authentication protocols can be carried within the Diameter
protocol. The PPP authentication protocols that are described are PAP
and CHAP.
The use of PAP SHOULD be discouraged, since it exposes user's
passwords to possibly non-trusted entities. However, PAP is also
frequently used for use with One-Time Passwords (OTP), which do not
expose a security risk.
This document also describes how CHAP can be carried within the
Diameter protocol, which is required for RADIUS backward
compatibility. The CHAP protocol, as used in a RADIUS environment,
facilitates authentication replay attacks.
13. References
13.1. Normative References
[Base] P. Calhoun, et.al, "Diameter Base Protocol", draft-ietf-
aaa-diameter-17.txt, IETF work in progress, December 2002.
[AAATrans] B. Aboba, J. Wood. "Authentication, Authorization and
Accounting (AAA) Transport Profile", draft-ietf-aaa-
transport-08, IETF work in progress, April 2002
[RADIUS] C. Rigney, A. Rubens, W. Simpson, S. Willens, "Remote
Authentication Dial In User Service (RADIUS)", RFC 2865,
June 2000.
[RADIUSTypes] IANA, "RADIUS Types", URL:
<http://www.iana.org/assignments/radius-types>
[RADIUSIPv6] B. Aboba, G. Zorn, D. Mitton, "RADIUS and IPv6", RFC 3162,
August 2001.
[IPv6Addr] Hinden, R., Deering, S., "IP Version 6 Addressing
Architecture", RFC 2373, July 1998
Calhoun et al. Expires August 2003 [Page 65]
INTERNET-DRAFT Diameter NAS Application Feb 2003
[PPPCHAP] W. Simpson, "PPP Challenge Handshake Authentication
Protocol (CHAP)", RFC 1994, August 1996.
[IANAConsid] Narten, Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs", BCP 26, RFC 2434, October
1998
[IANA] IANA Assigned Numbers Database, URL:
<http://www.iana.org/numbers.html>
[Keywords] S. Bradner, "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[ISOLatin] ISO 8859. International Standard -- Information Processing
-- 8-bit Single-Byte Coded Graphic Character Sets -- Part
1: Latin Alphabet No. 1, ISO 8859-1:1987. URL:
<http://www.iso.ch/cate/d16338.html>
[ANITypes] NANPA Number Resource Info, ANI Assignments, URL:
<http://www.nanpa.com/number_resource_info/
ani_ii_assignments.html>
13.2. Informative References
[NAI] B. Aboba, M. Beadles, "The Network Access Identifier." RFC
2486. January 1999.
[RADIUSAcct] C. Rigney, "RADIUS Accounting", RFC 2866, June 2000.
[RADIUSExt] C. Rigney, W. Willats, P. Calhoun, "RADIUS Extensions",
RFC 2869, June 2000.
[RADTunnels] G. Zorn, D. Leifer, A. Rubens, J. Shriver, M. Holdrege, I.
Goyret, "RADIUS Attributes for Tunnel Protocol Support",
RFC 2868, June 2000.
[RADTunlAcct] G. Zorn, B. Aboba, D. Mitton, "RADIUS Accounting
Modifications for Tunnel Protocol Support", RFC 2867, June
2000.
[RADDynAuth] M. Chiba, M Dommety, M. Eklund, D. Mitton, B. Aboba,
draft-chiba-radius-dynamic-authorization-06.txt", Work in
Progress, Jan 2003
[] D. Mitton, "Network Access Servers Requirements: Extended
RADIUS Practices", RFC 2882, July 2000.
Calhoun et al. Expires August 2003 [Page 66]
INTERNET-DRAFT Diameter NAS Application Feb 2003
[NASModel] D. Mitton, M. Beadles, "Network Access Server Requirements
Next Generation (NASREQNG) NAS Model", RFC 2881, July
2000.
[NASCriteria] M. Beadles, D. Mitton, "Criteria for Evaluating Network
Access Server Protocols", RFC 3169, September 2001.
[AAACriteria] Aboba, et al., "Criteria for Evaluating AAA Protocols for
Network Access", RFC 2989, Nov 2000.
[DiamEAP] G. Zorn, "Diameter EAP Application", draft-ietf-aaa-
eap-01.txt, IETF work in progress, August 2002.
[DiamCMS] P. Calhoun, W. Bulley, S. Farrell, "Diameter CMS Security
Application", draft-ietf-aaa-diameter-cms-sec-04.txt, IETF
work in progress, March 2002.
[DiamMIP] P. Calhoun, C. Perkins, T. Johansson, "Diameter Mobile IP
Application", draft-ietf-aaa-diameter-mobileip-13.txt,
IETF work in progress, October 2002.
[RAD802.1X] P. Congdon, et.al "IEEE 802.1X RADIUS Usage Guidelines",
draft-congdon-8021x-RADIUS-20.txt, IETF work in progress,
June 2002.
[802.1X] IEEE Standard for Local and metropolitan networks - Port-
Based Network Access Control, IEEE Std 802.1X-2001, June
2001
[CDMA2000] 3GPP2 "P.S0001-B", Wireless IP Network Standard, October
2002.
http://www.3gpp2.com/Public_html/specs/P.S0001-B_v1.0.pdf
[TCPCompress] Jacobson, "Compressing TCP/IP headers for low-speed serial
links", RFC 1144, February 1990.
[PPPMP] Sklower, Lloyd, McGregor, Carr, "The PPP Multilink
Protocol (MP)", RFC 1717, November 1994.
[PPTP] Hamzeh, K., Pall, G., Verthein, W., Taarud, J., Little,
W., Zorn, G., "Point-to-Point Tunneling Protocol (PPTP)",
RFC 2637, July 1999
[L2F] Valencia, A., Littlewood, M., Kolar, T., "Cisco Layer Two
Forwarding (Protocol) 'L2F'", RFC 2341, May 1998
[L2TP] Townsley, W. M., Valencia, A., Rubens, A., Pall, G. S.,
Zorn, G., Palter, B., "Layer Two Tunneling Protocol
Calhoun et al. Expires August 2003 [Page 67]
INTERNET-DRAFT Diameter NAS Application Feb 2003
(L2TP)", RFC 2661, August 1999
[ATMP] Hamzeh, K., "Ascend Tunnel Management Protocol - ATMP",
RFC 2107, February 1997
[MSMPPE] G. Pall, G. Zorn, "Microsoft Point-To-Point Encryption
(MPPE) Protocol", RFC 3078, March 2001.
[UTF-8] F. Yergeau, "UTF-8, a transformation format of ISO 10646",
RFC 2279, January 1998.
[STD51] W. Simpson, Editor, "The Point-to-Point Protocol (PPP)",
STD 51, RFC 1661, July 1994
14. Acknowledgements
The authors would like to thank Carl Rigney, Allan C. Rubens, William
Allen Simpson, and Steve Willens for their work on the original
RADIUS [RADIUS], from which many of the concepts in this
specification were derived. Thanks, also, to: Carl Rigney for
[RADIUSAcct] and [RADIUSExt]; Ward Willats for [RADIUSExt]; Glen
Zorn, Bernard Aboba and Dave Mitton for [RADTunlAcct] and [RADIPV6];
Dory Leifer, John Shriver, Matt Holdrege and Ignacio Goyret for their
work on [RADTunnels]. This document stole text and concepts from both
[RADTunnels] and [RADIUSExt]. Thanks go to Carl Williams for
providing IPv6 specific text.
The authors would also like to acknowledge the following people for
their contributions in the development of the Diameter protocol:
Bernard Aboba, Jari Arkko, William Bulley, Kuntal Chowdhury, Daniel
C. Fox, Lol Grant, Nancy Greene, Jeff Hagg, Peter Heitman, Paul
Krumviede, Fergal Ladley, Ryan Moats, Victor Muslin, Kenneth Peirce,
Sumit Vakil, John R. Vollbrecht and Jeff Weisberg.
Finally, Pat Calhoun would like to thank Sun Microsystems since most
of the effort put into this document was done while he was in their
employ.
15. Authors' Addresses
Questions about this memo can be directed to:
Pat R. Calhoun
Black Storm Networks
Calhoun et al. Expires August 2003 [Page 68]
INTERNET-DRAFT Diameter NAS Application Feb 2003
250 Cambridge Avenue, Suite 200
Palo Alto, California, 94306
USA
Phone: 1 650-617-2932
Fax: 1 650-786-6445
E-mail: pcalhoun@diameter.org
Glen Zorn
Cisco Systems, Inc.
500 108th Avenue N.E., Suite 500
Bellevue, WA 98004
USA
Phone: 1 425-471-4861
E-Mail: gwz@cisco.com
David Spence
Interlink Networks, Inc.
775 Technology Drive, Suite 200
Ann Arbor, MI 48108
USA
Phone: 1 734-821-1203
Fax: 1 734-821-1235
EMail: dspence@interlinknetworks.com
David Mitton
Circular Logic Unlimited
733 Turnpike St #154
North Andover, MA 01845
Email: david@mitton.com
Intellectual Property Considerations
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to per-
tain to the implementation or use of the technology described in this
document or the extent to which any license under such rights might
or might not be available; neither does it represent that it has made
any effort to identify any such rights. Information on the IETF's
procedures with respect to rights in standards-track and standards-
related documentation can be found in BCP-11. Copies of claims of
Calhoun et al. Expires August 2003 [Page 69]
INTERNET-DRAFT Diameter NAS Application Feb 2003
rights made available for publication and any assurances of licenses
to be made available, or the result of an attempt made to obtain a
general license or permission for the use of such proprietary rights
by implementers or users of this specification can be obtained from
the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English. The limited permissions granted above are perpetual and will
not be revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Calhoun et al. Expires August 2003 [Page 70]